Sun OS 5.8 Panic machine keeps rebooting

After shutdown I am not able to boot the machine.
Displays:
Warning: missing name/number? on line 1 of /etc/name_to_major
... same for all subsequent lines
Panic[cpu0] /thread=10408000: couldn't find major number for 'rootnex' .....
I am able to boot it with the Sun OS Cdrom via:
ok>boot cdrom -s and
#fsck /dev/rdsk/c0t0d0s0
#mount /dev/dsk/c0t0d0s0 /mnt
#umount /mnt
#reboot
The file /etc/name_to_major looks just fine.
How can I reboot normally again ?
Does anyone know if there are Sun patches for this ?

Boot cdrom and make sure there is a line in name_to_major that reads
rootnex 1
And that the permission on name_to_major are -rw-r--r-- owned by root:sys.

Similar Messages

Solaris 10 on Dual Athlon MP, can't install, keeps rebooting

Hi All,
I've been trying to install Solaris 10 onto my machine:
Tyan Thunder K7X (AMD 760MP Chipset)
2x AMD Athlon 2400+
2,5 GB Memory
Adaptec 2100S Raid Controllers
When the installation CD boots, you see a couple of dots appearing, then some text shows which quickly disappeared while the machine was rebooting. It was to fast for me to read, so I thought I might be a little more lucky by attaching a serial console to my pc. This captured the following information:
==========================================================
SunOS Release 5.10 Version Generic_118855-33 32-bit
Copyright 1983-2006 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
WARNING: Machine-Check Exception in kernel mode
WARNING: 0 STAT 0xf620a00000000833 ADDR 0x00000000000e4000
SUNW-MSG-ID: SUNOS-8000-0G, TYPE: Error, VER: 1, SEVERITY: Major
EVENT-TIME: 0x0.0x0 (0x0)
PLATFORM: i86pc, CSN: -, HOSTNAME:
SOURCE: SunOS, REV: 5.10 Generic_118855-33
DESC: Errors have been detected that require a reboot to ensure system
integrity. See http://www.sun.com/msg/SUNOS-8000-0G for more information.
AUTO-RESPONSE: Solaris will attempt to save and diagnose the error telemetry
IMPACT: The system will sync files, save a crash dump if needed, and reboot
REC-ACTION: Save the error summary below in case telemetry cannot be saved
panic[cpu0]/thread=fec1f4e0: Unrecoverable Machine-Check Exception
fec35720 unix:cmi_mca_trap+54 (fec3572c)
fec3572c unix:mcetrap+59 (fec301b0, fe810000,)
fec3577c acpica:AcpiUtTrackStackPtr+24 (cea4b010, fec357a0,)
fec35788 acpica:AcpiTbValidateRsdp+9 (cea4b010)
fec357a0 acpica:AcpiTbScanMemoryForRsdp+33 (cea47000, 20000)
fec357c8 acpica:AcpiTbFindRsdp+1d7 (fec357e0, 8)
fec35808 acpica:AcpiFindRootPointer+34 (8, fec35834, fec358)
fec35818 acpica:AcpiOsGetRootPointer+e (8, fec35834)
fec35850 acpica:AcpiGetFirmwareTable+57 (fec942d0, 1, 8, fec)
fec3586c acpica:acpica_metro_old_bios+18 (fec35904, 1, d59b1c)
fec35888 acpica:acpica_process_user_options+f9 (fec35904, 1, d59b1c)
fec3589c acpica:acpica_init+b (d59b1c68, fffffffe,)
fec358b0 acpica:acpi_isa_device_enum+9f (d59b1c68)
fec35920 isa:isa_alloc_nodes+e1 (d59b1c68)
fec35934 isa:isa_attach+2b (d59b1c68, 0)
fec35968 genunix:devi_attach+6f (d59b1c68, 0)
fec35984 genunix:attach_node+78 (d59b1c68)
fec3599c genunix:i_ndi_config_node+82 (d59b1c68, 6, 0)
fec359b4 genunix:i_ddi_attachchild+32 (d59b1c68)
fec359cc genunix:i_ddi_attach_node_hierarchy+60 (d59b1c68)
fec359e8 genunix:attach_driver_nodes+49 (78)
fec359f8 genunix:i_ddi_attach_pseudo_node+1c (fec071ac)
fec35a04 unix:configure+60 (fec35a14, fe818a2a,)
fec35a0c unix:startup_end+74 (fec35a24, fe8e3829,)
fec35a14 unix:startup+32 (fe800000, 100fed8, )
fec35a24 genunix:main+1b ()
skipping system dump - no dump device configured
rebooting...
==========================================================
Well I see some ACPI things there, so I tried to circumvent ACPI by one disabling ACPI in the BIOS, two, passing the user-acpi-options=0x2 to the kernel at boot time (tried also with just 2, 4 and 8, whatever they do :P).
The thing is, I kept getting exactly the same results, what's going on here? Is ACPI not disabled, is it not ACPI but something else? I've also tried it with less than 2GB RAM, since I read somebody had trouble installing with over 2GB RAM, but this wouldn't help either. Any help/tips/suggestions are greatly appreciated
My appologies if this thread seems similar I've posted the same question on an other place on the forum (before I found this place), but I think this is the place I should have posted this issue in the first place...

SOLVED:
Disabled ECC in the bios (though Windows and Gentoo Linux show now trouble whatsoever with my ECC memory, solaris doesn't like it)

Machine automatically reboots

I noticed my machine rebooted itself 3 days ago. Tonight it did the same and this is what I found in panic.log:
Sun Oct 30 19:52:28 2005panic(cpu 1 caller 0x0015E090): tcp_unlock: so=a306760 usecount=ffffffffLatest stack backtrace for cpu 1: Backtrace: 0x00095544 0x00095A5C 0x0002683C 0x0015E090 0x0028FF64 0x0028CEDC 0x0027F9D8 0x0025C034 0x0025C238 0x0025A330 0x0025A090 0x002A7A94 0x000ABCB0 0xDC2D8818 Proceeding back via exception chain: Exception state (sv=0x5EA75C80) PC=0x900138AC; MSR=0x0200F030; DAR=0x0037F88C; DSISR=0x40000000; LR=0x00453E74; R1=0xBFFFBF60; XCP=0x00000030 (0xC00 - System call)Kernel version:Darwin Kernel Version 8.2.0: Fri Jun 24 17:46:54 PDT 2005; root:xnu-792.2.4.obj~3/RELEASE_PPC*******
Does anyone know how to decipher this or where I should go from here? I have no idea why the machine is rebooting. I have a 3.5TB Xserve RAID connected to it and this machine is running as a webserver.

I had a CRS reboot issue on Solaris not too long ago. It ended up being an NTP issue. There are many reasons CRS could cause a node reboot. Possibly there is a timeout talking to the voting disks or OCR.
MetaLink Note:220970.1 is a good place to start for RAC questions. It has a section on Node reboots.
I also check out the CRS alert log and ocssd logs which can all be found in the CRS_HOME/log directory.

Desktop/Finder keeps rebooting after upgraded to Maverick (mac mini hooked up to a home theater system)

My desktop keeps rebooting ever since I upgraded to Mavericks.
Current setup, Mac Mini hooked up to home theater (Panasonic SC-HTB20) that is then hooked up to my Panasonic Plasma TV.
I usually leave my Mac Mini on running and at least once a day when I turn on the TV I can see that my desktop was rebooted. Firefox and Chrome will say that it wasn't shut down properly and if I want to restore my previous session. Also some times when I switched the input to watch TV and switch back, all my windows will be scattered out of place. For example Chrome will be in the top left hand corner to the point that it's almost minimized and I wouldn't be able to move it as well. Only thing I can do is close out these applications and relaunch them. It doesn't appear that the OS actually crashed, but more like the desktop/finder itself crashed. Cause once in a while I will switch back or turn on the TV and the screen will stay black for a few minutes then I'll see the cursor in the top right hand corner. After that I will start to see the desktop and my application start loading. It doesn't go through the regular process of rebooting where you see the Apple logo so I don't think the OS actually crashed but I could be wrong.
For some reason it seems like Maverick doesn't like the home theater system. An almost guarantee way to reproduce the issue is to wait for the home theater to turn off after it's been inactive for a while. If I turn it on the home theater to have the audio coming from it I will see the desktop goes black immediately then the whole desktop reboot process I mentioned above will kick in.
Never had any of these issues on 10.7 before I upgraded to Maverick.
Anybody have any suggestion? I really don't want to format and downgrade back to 10.7.
Thanks

Sounds like a kernel panic.
If you post the report we could have a go at deciphering it.
It would be in /Library/Logs/Diagnostic Reports.

My MBP keeps rebooting....!!!!

Hi guys I hope you will be able to help me
my mbp keeps rebooting every 15 minutes approximatively.
here is the kernel panic message :
Anonymous UUID:       BE16E9B5-F3D8-4A31-A408-6D7BB900F9AB
Tue Mar 25 11:27:55 2014
panic(cpu 0 caller 0xffffff8005adbe2e): Kernel trap at 0xffffef7f8644d940, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0xffffef7f8644d940, CR3: 0x000000002406d000, CR4: 0x0000000000000660
RAX: 0x0000000000000000, RBX: 0xffffef7f8644d940, RCX: 0xffffef7f8644d940, RDX: 0x0000000000000000
RSP: 0xffffff80f6e9bfb8, RBP: 0x0000000000000000, RSI: 0x0000000000000000, RDI: 0xffffff8020b92f78
R8: 0xffffff80060d2b30, R9: 0x0000000000000000, R10: 0xffffff80f6e9be20, R11: 0xffffff8006089ce8
R12: 0xffffff801777eb20, R13: 0xffffff801a054000, R14: 0xffffff80060d2ab8, R15: 0xffffff801a054028
RFL: 0x0000000000010246, RIP: 0xffffef7f8644d940, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0xffffef7f8644d940, Error code: 0x0000000000000010, Fault CPU: 0x0
Backtrace (CPU 0), Frame : Return Address
0xffffff80f6e9bc40 : 0xffffff8005a22fa9
0xffffff80f6e9bcc0 : 0xffffff8005adbe2e
0xffffff80f6e9be90 : 0xffffff8005af3326
0xffffff80f6e9beb0 : 0xffffef7f8644d940
BSD process name corresponding to current thread: Adobe Photoshop
Mac OS version:
13C64
Kernel version:
Darwin Kernel Version 13.1.0: Thu Jan 16 19:40:37 PST 2014; root:xnu-2422.90.20~2/RELEASE_X86_64
Kernel UUID: 9FEA8EDC-B629-3ED2-A1A3-6521A1885953
Kernel slide:     0x0000000005800000
Kernel text base: 0xffffff8005a00000
System model name: MacBookPro5,3 (Mac-F22587C8)
System uptime in nanoseconds: 654837165862
last loaded kext at 269622262382: com.apple.filesystems.msdosfs          1.9 (addr 0xffffff7f86a26000, size 65536)
last unloaded kext at 494781948647: com.lacie.driver.LaCie_RemoteComms          1.0.1 (addr 0xffffff7f86a3e000, size 8192)
loaded kexts:
com.oxsemi.driver.OxsemiDeviceType00          1.28.13
com.apple.driver.AudioAUUC          1.60
com.apple.driver.AppleHWSensor          1.9.5d0
com.apple.driver.AGPM          100.14.15
com.apple.filesystems.autofs          3.0
com.apple.iokit.IOBluetoothSerialManager          4.2.3f10
com.apple.driver.AppleMikeyHIDDriver          124
com.apple.driver.AppleHDA          2.6.0f1
com.apple.driver.AppleSMCLMU          2.0.4d1
com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
com.apple.driver.AppleMikeyDriver          2.6.0f1
com.apple.iokit.IOUserEthernet          1.0.0d1
com.apple.Dont_Steal_Mac_OS_X          7.0.0
com.apple.driver.AppleHWAccess          1
com.apple.GeForceTesla          8.2.4
com.apple.driver.AppleUpstreamUserClient          3.5.13
com.apple.driver.AppleMCCSControl          1.1.12
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport          4.2.3f10
com.apple.driver.AppleMuxControl          3.4.35
com.apple.driver.AppleLPC          1.7.0
com.apple.driver.SMCMotionSensor          3.0.4d1
com.apple.driver.AppleUSBTCButtons          240.2
com.apple.driver.AppleUSBTCKeyboard          240.2
com.apple.driver.AppleIRController          325.7
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
com.apple.BootCache          35
com.apple.driver.AppleUSBCardReader          3.4.1
com.apple.iokit.SCSITaskUserClient          3.6.6
com.apple.driver.XsanFilter          404
com.apple.iokit.IOAHCIBlockStorage          2.5.1
com.apple.driver.AppleFWOHCI          4.9.9
com.apple.driver.AppleUSBHub          666.4.0
com.apple.driver.AirPort.Brcm4331          700.20.22
com.apple.driver.AppleAHCIPort          3.0.0
com.apple.nvenet          2.0.21
com.apple.driver.AppleUSBEHCI          660.4.0
com.apple.driver.AppleUSBOHCI          656.4.1
com.apple.driver.AppleSmartBatteryManager          161.0.0
com.apple.driver.AppleRTC          2.0
com.apple.driver.AppleHPET          1.8
com.apple.driver.AppleACPIButtons          2.0
com.apple.driver.AppleSMBIOS          2.1
com.apple.driver.AppleACPIEC          2.0
com.apple.driver.AppleAPIC          1.7
com.apple.driver.AppleIntelCPUPowerManagementClient          216.0.0
com.apple.nke.applicationfirewall          153
com.apple.security.quarantine          3
com.apple.driver.AppleIntelCPUPowerManagement          216.0.0
com.apple.AppleGraphicsDeviceControl          3.4.35
com.apple.kext.triggers          1.0
com.apple.iokit.IOSerialFamily          10.0.7
com.apple.driver.DspFuncLib          2.6.0f1
com.apple.vecLib.kext          1.0.0
com.apple.iokit.IOAudioFamily          1.9.5fc2
com.apple.kext.OSvKernDSPLib          1.14
com.apple.driver.IOPlatformPluginLegacy          1.0.0
com.apple.driver.AppleSMBusPCI          1.0.12d1
com.apple.iokit.IOSurface          91
com.apple.iokit.IOBluetoothFamily          4.2.3f10
com.apple.nvidia.classic.NVDANV50HalTesla          8.2.4
com.apple.driver.AppleSMBusController          1.0.11d1
com.apple.nvidia.classic.NVDAResmanTesla          8.2.4
com.apple.iokit.IOBluetoothHostControllerUSBTransport          4.2.3f10
com.apple.iokit.IOFireWireIP          2.2.6
com.apple.driver.AppleHDAController          2.6.0f1
com.apple.iokit.IOHDAFamily          2.6.0f1
com.apple.driver.AppleBacklightExpert          1.0.4
com.apple.driver.AppleGraphicsControl          3.4.35
com.apple.driver.IOPlatformPluginFamily          5.7.0d10
com.apple.iokit.IONDRVSupport          2.4.1
com.apple.iokit.IOGraphicsFamily          2.4.1
com.apple.driver.AppleSMC          3.1.8
com.apple.driver.AppleUSBMultitouch          240.9
com.apple.iokit.IOUSBHIDDriver          660.4.0
com.apple.iokit.IOUSBMassStorageClass          3.6.0
com.apple.driver.AppleUSBMergeNub          650.4.0
com.apple.driver.AppleUSBComposite          656.4.1
com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.6.6
com.apple.iokit.IOBDStorageFamily          1.7
com.apple.iokit.IODVDStorageFamily          1.7.1
com.apple.iokit.IOCDStorageFamily          1.7.1
com.apple.iokit.IOSCSIBlockCommandsDevice          3.6.6
com.apple.iokit.IOAHCISerialATAPI          2.6.1
com.apple.iokit.IOSCSIArchitectureModelFamily          3.6.6
com.apple.iokit.IOFireWireFamily          4.5.5
com.apple.iokit.IOUSBUserClient          660.4.2
com.apple.iokit.IO80211Family          630.35
com.apple.iokit.IOAHCIFamily          2.6.5
com.apple.iokit.IONetworkingFamily          3.2
com.apple.iokit.IOUSBFamily          675.4.0
com.apple.driver.NVSMU          2.2.9
com.apple.driver.AppleEFINVRAM          2.0
com.apple.driver.AppleEFIRuntime          2.0
com.apple.iokit.IOHIDFamily          2.0.0
com.apple.iokit.IOSMBusFamily          1.1
com.apple.security.sandbox          278.11
com.apple.kext.AppleMatch          1.0.0d1
com.apple.security.TMSafetyNet          7
com.apple.driver.AppleKeyStore          2
com.apple.driver.DiskImages          371.1
com.apple.iokit.IOStorageFamily          1.9
com.apple.iokit.IOReportFamily          23
com.apple.driver.AppleFDEKeyStore          28.30
com.apple.driver.AppleACPIPlatform          2.0
com.apple.iokit.IOPCIFamily          2.9
com.apple.iokit.IOACPIFamily          1.4
com.apple.kec.pthread          1
com.apple.kec.corecrypto          1.0
Model: MacBookPro5,3, BootROM MBP53.00AC.B03, 2 processors, Intel Core 2 Duo, 3.06 GHz, 8 GB, SMC 1.48f2
Graphics: NVIDIA GeForce 9400M, NVIDIA GeForce 9400M, PCI, 256 MB
Graphics: NVIDIA GeForce 9600M GT, NVIDIA GeForce 9600M GT, PCIe, 512 MB
Memory Module: BANK 0/DIMM0, 4 GB, DDR3, 1333 MHz, 0x029E, 0x434D534F344758334D314131333333433920
Memory Module: BANK 1/DIMM0, 4 GB, DDR3, 1333 MHz, 0x029E, 0x434D534F344758334D314131333333433920
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8D), Broadcom BCM43xx 1.0 (5.106.98.100.22)
Bluetooth: Version 4.2.3f10 13477, 3 services, 15 devices, 1 incoming serial ports
Network Service: Wi-Fi, AirPort, en1
Serial ATA Device: ST9500420AS, 500,11 GB
Serial ATA Device: HL-DT-ST DVDRW GS23N
USB Device: iPhone
USB Device: Built-in iSight
USB Device: Internal Memory Card Reader
USB Device: Apple Internal Keyboard / Trackpad
USB Device: IR Receiver
USB Device: PTK-540WL
USB Device: BRCM2046 Hub
USB Device: Bluetooth USB Host Controller
Thunderbolt Bus:
Thanks in advance for your help !

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you boot, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, reboot as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

My E3200 keeps rebooting

Factory Refurbished version, when i received it, and found it just keeps rebooting.
so i used a serial cable and get in CFE
use cmd " upgrade code.bin" to flash offical firmwire 1.04, it show succesful. but not working. still keeps rebooting.
can you take a look what is wrong with it.
here is the info from serial port, from start to rebooting.
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Fri Mar 4 11:57:55 HKT 2011 (zhaoguang@sw1)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
This is a Serial Flash
Boot partition size = 262144(0x40000)
Found a 16MB ST compatible serial flash
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.127.28 @VERSION_TYPE@
CPU type 0x19749: 500MHz
Tot mem: 65536 KBytes
CFE mem: 0x80700000 - 0x807A02F0 (656112)
Data: 0x80735600 - 0x80739640 (16448)
BSS: 0x80739640 - 0x8073A2F0 (3248)
Heap: 0x8073A2F0 - 0x8079E2F0 (409600)
Stack: 0x8079E2F0 - 0x807A02F0 (8192)
Text: 0x80700000 - 0x807355F4 (218612)
Boot version: v5.9
The boot is CFE
Flash base: bfc00000, mac start: 3ef00
mac_init(): Find mac [58:6D:8F:1D:3A:97] in location 0
Nothing...
No country code find
### CLKDIV= 0x20e0842, SFlashClkDiv=2 clkdivsf=2 ###
### Change it to 0x20e0842 (2) ###
Device eth0: hwaddr 58-6D-8F-1D-3A-97, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
cfe_led_init: start to set power LED and switch LEDs.
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: .. 3731948 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22 (root@97026PC) (gcc version 4.2.3) #2 Tue Apr 10 19:05:47 CST 2012
CPU revision is: 00019749
Found a 16MB ST compatible serial flash
wombo_reset set to gpio 23
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0 -> 16384
HighMem 16384 -> 16384
early_node_map[1] active PFN ranges
0: 0 -> 16384
Built 1 zonelists. Total pages: 16384
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM5357 rev 1 at 500 MHz
Using 250.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60220k/65536k available (2869k kernel code, 5260k reserved, 563k data, 212k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
PCI: no core
PCI: Fixing up bus 0
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
gpio_init: power pulse time 7
Register DIAG LED in /proc/sys/diag_blink.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
fuse init (API version 7.8)
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
loop: module loaded
PPP generic driver version 2.4.2
NET: Registered protocol family 24
pflash: found no supported devices
sflash: squash filesystem with lzma found at block 1800
Creating 4 MTD partitions on "sflash":
0x00000000-0x00040000 : "boot"
0x00040000-0x00ff0000 : "linux"
0x001c2154-0x00ff0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x00ff0000-0x01000000 : "nvram"
u32 classifier
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
edward ====to register conntrack protocol helper for esp:
nf_conntrack_rtsp v0.6.21 loading
GRE over IPv4 tunneling driver
nf_nat_rtsp v0.6.21 loading
edward =======nf_nat_proto_esp_init
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 212k freed
Warning: unable to open an initial console.
Failed to execute /init
ctmisc: module license 'unspecified' taints kernel.
Register /dev/ctmisc device, major:10 minor:255
cmd=[touch /tmp/var/lib/nfs/xtab ]
cmd=[chmod 644 /tmp/var/lib/nfs/xtab ]
cmd=[touch /tmp/var/lib/nfs/etab ]
cmd=[chmod 644 /tmp/var/lib/nfs/etab ]
cmd=[touch /tmp/var/lib/nfs/rmtab ]
cmd=[chmod 644 /tmp/var/lib/nfs/rmtab ]
cmd=[touch /tmp/var/lib/nfs/state ]
cmd=[chmod go-rwx /tmp/var/lib/nfs/state ]
cmd=[touch /tmp/disk_updating_lock ]
cmd=[chmod 644 /tmp/disk_updating_lock ]
cmd=[touch /tmp/file_variable_updating_lock ]
cmd=[chmod 644 /tmp/file_variable_updating_lock ]
cmd=[/sbin/hotplug2 --coldplug & ]
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
[sighandler]: No more events to be processed, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
The boot is CFE
Algorithmics/MIPS FPU Emulator v1.5
/dev/: cannot create
cmd=[misc -t get_mac -w 3 ]
ctmisc_ioctl: cmd=0x11, buffer size=196
data_init(): base = 0xbc03ef00
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get MAC count is [1]
get_data(): MAC 0: [58:6D:8F:1D:3A:97]
get_data(): done
cmd=[misc -t get_wsc_pin -w 3 ]
ctmisc_ioctl: cmd=0x26, buffer size=196
data_init(): base = 0xbc03fcdc
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get WSC count is [1]
get_data(): WSC 0: [71674483]
get_data(): done
cmd=[misc -t get_sn -w 3 ]
ctmisc_ioctl: cmd=0x15, buffer size=196
data_init(): base = 0xbc03fe30
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get SN count is [1]
get_data(): SN 0: [10B10C16103018]
get_data(): done
cmd=[misc -t get_country -w 3 ]
ctmisc_ioctl: cmd=0x2c, buffer size=196
data_init(): base = 0xbc03fe20
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get COUNTRY count is [0]
get_data(): done
cmd=[misc -t get_2g_country_code -w 3 ]
ctmisc_ioctl: cmd=0x2e, buffer size=196
data_init(): base = 0xbc03fe10
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get 2G_COUNTRY_CODE count is [0]
get_data(): done
cmd=[misc -t get_5g_country_code -w 3 ]
ctmisc_ioctl: cmd=0x5e, buffer size=196
data_init(): base = 0xbc03fe00
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get 5G_COUNTRY_CODE count is [0]
get_data(): done
cmd=[misc -t get_flash_type -w 1 ]
ctmisc_ioctl: cmd=0x17, buffer size=196
sflash_init: sflash type 0x100
sflash_init: sflash type 0x17
Flash Type: SFLASH 16384 kB
tallest:=====(ctmisc ioctl done...)=====
Get FLASH TYPE is [SFLASH 16384 kB]
cmd=[misc -t get_pa2ga0idxval -w 3 ]
ctmisc_ioctl: cmd=0x28, buffer size=196
data_init(): base = 0xbc03f6c0
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get PA2GA0IDXVAL count is [1]
get_data(): PA2GA0IDXVAL 0: [11 -428 8175 -1979]
get_data(): done
cmd=[misc -t get_ctmisc_ioctl: cmd=0x2a, buffer size=196
pa2ga1idxval -w data_init(): base = 0xbc03f600
3 ]
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get PA2GA1IDXVAL count is [1]
get_data(): PA2GA1IDXVAL 0: [9 -410 7973 -1911]
get_data(): done
2G idx[11] w0a0[-428] w1a0[8175] wctmisc_ioctl: cmd=0x38, buffer size=196
2a0[-1979]
2G idata_init(): base = 0xbc03f4c0
dx[9] w0a1[-410]data_init(): location = [1], mydatas index = 1
w1a1[7973] w2a1ctmisc_ioctl: index=1
[-1911]
cmd=[mitallest:=====(ctmisc ioctl done...)=====
sc -t get_pa5gha0idxval -w 3 ]
get_data(): Get PA5GHA0IDXVAL count is [1]
get_data(): PA5GHA0IDXVAL 0: [0 -323 6175 -1379]
get_data(): done
ctmisc_ioctl: cmd=0x3a, buffer size=196
cmd=[misc -t getdata_init(): base = 0xbc03f400
_pa5gha1idxval -data_init(): location = [1], mydatas index = 1
w 3 ]
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get PA5GHA1IDXVAL count is [1]
get_data(): PA5GHA1IDXVAL 0: [1 -327 6085 -1372]
get_data(): done
5G high idx[0] w0a0[-323] w1a0[6ctmisc_ioctl: cmd=0x3c, buffer size=196
175] w2a0[-1379]data_init(): base = 0xbc03f980
5G high idx[1]data_init(): location = [0], mydatas index = 0
w0a1[-327] w1a1ctmisc_ioctl: index=0
[6085] w2a1[-137tallest:=====(ctmisc ioctl done...)=====
2]
cmd=[misc -t get_pa5gha2idxval -w 3 ]
get_data(): Get PA5GHA2IDXVAL count is [0]
get_data(): done
Using default 5G high PA2 value
cmd=[mctmisc_ioctl: cmd=0x48, buffer size=196
isc -t get_pa5gldata_init(): base = 0xbc03f2c0
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get PA5GLA0IDXVAL count is [0]
get_data(): done
cmd=[misc -t get_pa5gla1idxval -w 3 ]
ctmisc_ioctl: cmd=0x4a, buffer size=196
data_init(): base = 0xbc03f200
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get PA5GLA1IDXVAL count is [0]
get_data(): done
Using default 5G low PA0 value
Using default 5G low PA1 value
cmd=[misc -t get_pctmisc_ioctl: cmd=0x4c, buffer size=196
a5gla2idxval -w data_init(): base = 0xbc03f8c0
3 ]
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get PA5GLA2IDXVAL count is [0]
get_data(): done
Using default 5G low PA2 value
cmd=[misc -t get_pa5ga0idxval -w 3 ]
ctmisc_ioctl: cmd=0x58, buffer size=196
data_init(): base = 0xbc03f0c0
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get PA5GA0IDXVAL count is [1]
get_data(): PA5GA0IDXVAL 0: [5 -381 6478 -1507]
get_data(): done
cmd=[misc -t get_pctmisc_ioctl: cmd=0x5a, buffer size=196
a5ga1idxval -w 3data_init(): base = 0xbc03f000
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get PA5GA1IDXVAL count is [1]
get_data(): PA5GA1IDXVAL 0: [7 -374 6543 -1519]
get_data(): done
5G middle idx[5] w0a0[-381] w1a0[6ctmisc_ioctl: cmd=0x5c, buffer size=196
478] w2a0[-1507]data_init(): base = 0xbc03f800
5G middle idx[data_init(): location = [0], mydatas index = 0
7] w0a1[-374] w1ctmisc_ioctl: index=0
a1[6543] w2a1[-1tallest:=====(ctmisc ioctl done...)=====
519]
cmd=[misc -t get_pa5ga2idxval -w 3 ]
get_data(): Get PA5GA2IDXVAL count is [0]
get_data(): done
Using default 5G middle PA2 value
Cannot find lang from /proc/mtd
ret = -1
www -> /www
mount: No such file or directory
cmd=[insmod emf ]
cmd=[insmod igs ]
cmd=[insmod ctf ]
cmd=[insmod /lib/ufsd.ko ]
Needed modules: et wl ip6t_frag ip6t_ipv6header ip6t_ipv6range
cmd=[insmod et ]
cmd=[insmod wl ]
cmd=[insmod ip6t_frag ]
cmd=[insmod ip6t_ipv6header ]
cmd=[insmod ip6t_ipv6range ]
cmd=[insmod usbcore ]
cmd=[insmod usb-storage ]
cmd=[insmod ehci-hcd log2_irq_thresh=3 qtdc_pid=48407 qtdc_vid=2652 qtdc0_ep=4 qtdc0_sz=0 qtdc1_ep=18 qtdc1_sz=10 ]
cmd=[insmod ohci-hcd ]
cmd=[insmod wl_high instance_base=1 ]
eth2: No such device
wl0 not up in 3 sec
cmd=[insmod sxuptp_wq.ko ]
cmd=[insmod sxuptp.ko ]
cmd=[insmod sxuptp_driver.ko ]
cmd=[insmod jcp.ko ]
cmd=[insmod dnshook ]
Failed trying to open `/proc/mdstat': No such file or directory
Failed trying to open `/proc/sestat': No such file or directory
Failed trying to open `/proc/mdstat': No such file or directory
Failed trying to open `/proc/sestat': No such file or directory
Hit enter to continue...The chipset is 47186 with a 53125 gigabit switch
[sighandler]: Obtained SIGINT, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
[sighandler]: Obtained SIGINT, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
[sighandler]: Obtained SIGINT, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
[sighandler]: Obtained SIGINT, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
[sighandler]: Obtained SIGINT, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
[sighandler]: Obtained SIGINT, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
cmd=[killall httpd ]
killall: httpd: no process killed
waitpid: No child processes
killall: check_http.sh: no process killed
cmd=[killall gn-httpd ]
killall: gn-httpd: no process killed
cmd=[killall gn-httpd ]
killall: gn-httpd: no process killed
waitpid: No child processes
cmd=[killall wm-httpd ]
killall: wm-httpd: no process killed
waitpid: No child processes
cmd=[et robowr 0x02 0x06 0x001000a0 ]
cmd=[resetbutton ]
waitpid: No child processes
cmd=[vconfig set_name_type VLAN_PLUS_VID_NO_PAD ]
cmd=[vconfig add eth0 1 ]
cmd=[vconfig set_ingress_map vlan1 0 0 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 1 1 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 2 2 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 3 3 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 4 4 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 5 5 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 6 6 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 7 7 ]
waitpid: No child processes
cmd=[vconfig add eth0 2 ]
cmd=[vconfig set_ingress_map vlan2 0 0 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 1 1 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 2 2 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 3 3 ]
cmd=[vconfig set_ingress_map vlan2 4 4 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 5 5 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 6 6 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 7 7 ]
waitpid: No child processes
cmd=[brctl addbr br0 ]
cmd=[brctl setfd br0 0 ]
waitpid: No child processes
cmd=[brctl stp br0 dis ]
expect on/off for argument
waitpid: No child processes
cmd=[brctl addif br0 vlan1 ]
waitpid: No child processes
br0: No child processes
cmd=[wlconf vlan1 up ]
vlan1: Operation not supported
Write wireless mac successfully
cmd=[brctl addif br0 eth1 ]
br0: No child processes
cmd=[wlconf eth1 up ]
eth1: Operation not supported
eth1: Operation not permitted
interface eth1: channel selected 1 (renew)
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Invalid argument
eth1: Invalid argument
eth1: Operation not supported
cmd=[brctl addif br0 eth1 ]
device eth1 is already a member of a bridge; can't enslave it to bridge br0.
waitpid: No child processes
Write wireless mac fail : : No such device
cmd=[brctl addif br0 eth2 ]
interface eth2 does not exist!
eth2: No such device
cmd=[brctl addif br0 eth3 ]
interface eth3 does not exist!
eth3: No such device
Set 1 to /proc/sys/net/ipv6/conf/br0/forwarding ...
wl: wl driver adapKernel panic - not syncing: Attempted to kill init!
ter not found
URebooting in 3 seconds..pdate [-428] to [0xfe54]
Update [8175] to [0x1fef]
Update [-1979] to [0xf845]
Update [-410] to [0xfe66]
Update [7973] to [0x1f25]
Update [-1911] to [0xf889]
Update [-323] to [0xfebd]
Update [6175] to [0x181f]
Update [-1379] to [0xfa9d]
Update [-327] to [0xfeb9]
Update [6085] to [0x17c5]
Update [-1372] to [0xfaa4]
Update [-381] to [0xfe83]
Update [6478] to [0x194e]
Update [-1507] to [0xfa1d]
Update [-374] to [0xfe8a]
Update [6543] to [0x198f]
Update [-1519] to [0xfa11]
Restoring Storage Nvram Defaults
signalling STOP
Make date==>Year:12,Month:4,Day:10
Firmware version =>v1.0.04
signalling STOP
signalling STOP
signalling STOP
sum3=10679296 garbage=992 n=1024
MD5=[8ef631c90b58a3b4e051ca06072bbc4a]
signalling STOP
WARNING: console log level set to 1
name=[vlan1] lan_ifname=[br0]
name=[eth1] lan_ifname=[br0]
name=[eth2] lan_ifname=[br0]
name=[eth3] lan_ifname=[br0]
Please stand by while rebooting the system...

part 2
wl1_bcn_rotate=1
wsc_config_method=pin
storage_group_desc7=
switch_netmask=0.0.0.0
usb/0xBD17/mcs5gpo5=0x0000
storage_group_desc8=
usb/0xBD17/mcs5gpo6=0x0000
usb/0xBD17/pa5ghw2a0=0xfa9d
wl_wps_reg=disabled
sel_qosport1=0
storage_group_desc9=
usb/0xBD17/mcs5gpo7=0x0000
usb/0xBD17/pa5ghw2a1=0xfaa4
filter_mac_grp10=
wl0_wds=
ipv6_filter=on
sel_qosport2=0
mount_disk_result=0
ppp_static_ip=
wl1_widechannel=0
sel_qosport3=0
log_level=0
wl1_wme_sta_be=15 1023 3 0 0 off off
tunnel_prefix_len=0
block_java=0
forward_portsip=
ddns_service=dyndns
sel_qosport4=0
storage_group_access20=
ct_modules=
ntp_server=
wpa_gtk_rekey_24g=3600
wl0_reg_mode=off
wl1_closed=0
sel_qosport5=0
storage_group_access21=
wan_hwaddr=
wps_mfstring=Cisco
wl1_bss_enabled=1
lan_ipv6_dns=
sel_qosport6=0
storage_group_access0=0
storage_group_access22=
QoS_cnt=0
wep_5g=disabled
sel_qosport7=0
storage_group_access1=1
storage_group_access23=
get_pa5gla1idxval_index=0
lan_ifnames=vlan1 eth1 eth2 eth3
wl1_akm=
wl1_reg_mode=off
lan_ipv6_dns_primary=
sel_qosport8=0
storage_group_access2=
storage_group_access24=
ftp_share_folder_0=
usb/0xBD17/pa05gidx=5
pppoe_ifname=
hwaddr_24g=
storage_group_access3=
storage_group_access25=
ftp_share_folder_1=
wl_40m_disable=0
wl0_auth=0
wl0_radius_port=1812
wl0_wme=on
wl0_mac_deny=
wl1_wme_sta_bk=15 1023 7 0 0 off off
wan_ipv6_renew=0
storage_group_access4=
storage_group_access26=
tunnel_status=disconnected
ftp_share_folder_2=
passphrase_5g=
tunnel_br=
blank_disk_info=
storage_group_access5=
storage_group_access27=
ftp_share_folder_3=
wl0_radius_ipaddr=
wl0_wme_bss_disable=0
wep_gen_5g=
wl1_radio=1
all_partitions_share=1
storage_group_access6=
ftp_share_folder_4=
pppoe_service=
auth_type_5g=0
wep_bit_5g=64
wl1_mac_deny=
storage_group_access7=
ftp_share_folder_5=
wl_country=US
ure_disable=1
wl0_wme_sta_vi=7 15 2 6016 3008 off off
gn_last_cable_stat=0
storage_group_access8=
ftp_share_folder_6=
wl1_antdiv=-1
tunnel_mode=0
storage_group_access9=
ftp_share_folder_7=
sb/1/boardflags=0x80001710
mfg_radio=off
ftp_share_folder_8=
traceroute_ip=
dhcp_start_conflict=0
ftp_share_folder_9=
ddns_change=
sb/1/leddc=0xFFFF
wan_ifnames=vlan2
key1_24g=
remote_management=0
sb/1/tempoffset=0
get_sern=1234567890
wl0_wme_sta_vo=3 7 2 3264 1504 off off
gn_approval_list=
block_loopback=0
wl1_ap_isolate=0
usb_mode=3
wl1_security_mode=disabled
get_pa5gla2idxval_index=0
http_method=post
ppp_mru=1500
wl1_wme_no_ack=off
wl0.1_mode=ap
clkfreq=500,200,100
os_name=linux
upnp_internet_dis=0
lan_proto=dhcp
lan_ipaddr=192.168.1.1
filter_port_grp1=
wl1_auth_type=0
wl1_radius_port=1812
dslite_cgn_addr=2001:db8:ff4e:11::8
QoS=0
usb/0xBD17/boardflags2=0x00200000
vlan1hwname=et0
filter_port_grp2=
wl0_maxassoc=128
filter_port_grp3=
filter_port_grp10=
auth_5g=0
ddns_passwd_2=
foreign_disk_info=
filter_id=1
filter_port_grp4=
wl1_plcphdr=long
dr_wan_tx=0
filter_port_grp5=
wl0_phytypes=
wl1_maxassoc=128
wl1_macmode=disabled
switch_mode=0
router_disable=0
filter_port_grp6=
wl0_wep=disabled
wl0_frag=2346
wps_sta_pin=00000000
read_disk_result=0
usb/0xBD17/ag0=0x84
filter_port_grp7=
wl1_phytype=n
wl0.1_closed=0
ddns_username=
switch_get_domain=
usb/0xBD17/ag1=0x84
filter_port_grp8=
pppoe_passwd=
wl1_phytypes=
wl1_lazywds=0
ddns_passwd=
remote_ftp=1
usb/0xBD17/mcs5glpo0=0x0000
usb/0xBD17/ag2=0x84
filter_port_grp9=
nbw_24g=20
wl0_nbw=20
auth_24g=0
lan_ipv6_addr=
gn_lan_ipv6_addr=
usb/0xBD17/regrev=0
usb/0xBD17/mcs5glpo1=0x0000
usb/0xBD17/pa5glw1a0=0x177C
sdram_config=0x0103
log_enable=0
ppp_ac=
storage_group_name10=
get_pa2ga1idxval=9 -410 7973 -1911
sys_country=US
usb/0xBD17/cddpo=0x0000
usb/0xBD17/mcs5glpo2=0x0000
usb/0xBD17/pa5glw1a1=0x16DA
filter_web_url10=
wl0_country=Q2/3
wl0_radarargs40_11n=5 4 4 100 0x6b0 0x6d9 0x2c40 0x7f07 12 195 2000 25
400000000 1000 6000000
storage_group_name11=
usb/0xBD17/mcs5glpo3=0x0000
sb/1/temps_hysteresis=5
vlan1ports=0 1 2 3 8*
dmz_ipaddr=0
storage_users_limit=20
storage_group_name12=
usb/0xBD17/pa15glidx=0
usb/0xBD17/mcs5glpo4=0x0000
usb/0xBD17/pa5gw2a0=0xfa1d
wl_txq_thresh=256
wl_wds=
storage_group_name13=
ftp_share_access=1:admin:rw
auth_exemption_list=
usb/0xBD17/mcs5glpo5=0x0000
usb/0xBD17/pa5gw2a1=0xfa11
wl1_dfs_preism=60
ddns_hostname_2=
storage_group_name14=
igmp_version=0
usb/0xBD17/mcs5glpo6=0x0000
radius_ipaddr_5g=
users_content=admin:admin:admin:adminff guest:guest:guest:guestn
dir_list=/foreign_shares
storage_group_name15=
usb/0xBD17/mcs5glpo7=0x0000
wl1_mode=ap
storage_group_name16=
boot_hw_ver=1.0
wl0_rateset=default
wl0.1_ssid=Cisco03018-guest
lan_ipv6_domain=
storage_group_name17=
usb/0xBD17/txq_len=256
wan_ipv6_gateway=
storage_group_name18=
sb/1/macaddr=00:16:B6:C4:71:B2
wl0_wme_apsd=on
wl1_wpa_psk=
storage_group_name19=
get_pa5ga1idxval=7 -374 6543 -1519
sb/1/ccode=0
qtdc1_ep=18
TMSSS_enable=0 0 65
closed_24g=0
wl0_wep_bit=64
pppoe_idletime=15
wl_wme=on
get_mac=58:6D:8F:1D:3A:97
ping_times=5
net_reauth_5g=36000
wl1_wme_apsd=on
gn_max_account=5
forward_single=
qos_enable_ever=0
get_2g_country_code_index=0
lan_ifname=br0
remote_upgrade=0
usb/0xBD17/pa25ghidx=0
wl1_ui_channels=36,40,44,48,149,153,157,161
boardflags=0x80001710
filter_services=$NAME:003NS$PROT:003:udp$PORT:005:53:53< >$NAME:004:
Ping$PROT:004:icmp$PORT:003:0:0< >$NAME:004:HTTP$PROT:003:tcp$PORT:005
:80:80<tcp$PORT:005:21:21< >$NAME:004OP3
$PROT:003:tcp$PORT:007:110:110< >$NAME:004:IMAP$PROT:003:tcp$PORT:007:
143:143< >$NAME:004MTP$PROT:003:tcp$PORT:005:25:25< >$NAME:004:
NNTP$PROT:003:tcp$PORT:007:119:119< >$NAME:006:Telnet$PROT:003:tcp$POR
T:005:23:23< >$NAME:004NMP$PROT:003:udp$PORT:007:161:161< >$NAM
E:004:TFTP$PROT:003:udp$PORT:005:69:69< >$NAME:003:IKE$PROT:003:udp$PO
RT:007:500:500< >
wandevs=vlan2
sdram_refresh=0x1a5b
gn_cur_account=0
sb/1/cck2gpo=0x0000
dhcp_domain=wan
lan_ipv6_dns_mode=1
wan_ipv6_prefixlen=0
et_txq_thresh=256
sdram_ncdl=0x5800001a
sb/1/pa2gw0a0=0xfe54
wl1_wme_ap_vi=7 15 1 6016 3008 off off
wan_gateway_buf=0.0.0.0
ftp_all=1
sb/1/pa2gw0a1=0xfe66
block_cookie=0
usb/0xBD17/maxp5ga0=0x48
sb/1/phycal_tempdelta=0
ezc_enable=1
usb/0xBD17/maxp5ga1=0x48
safe_mode_upgrade=off
wl0_nmode_protection=auto
ssid_5g=Cisco03018
ftp_share_folder_10=
wl1_ssid=Cisco03018
wl1_dtim=1
wsc_result=0
upnp_wan_proto=
is_modified=0
usb/0xBD17/stbcpo=0x0000
wan_ipaddr=0.0.0.0
filter_web_url1=
dhcp_num=50
filter_web_url2=
ppp_demand_hb=0
wl0_passphrase=
usb/0xBD17/bwduppo=0
usb/0xBD17/aa5g=7
filter_web_url3=
usb/0xBD17/elna5g=2
usb/0xBD17/txchain=3
filter_web_url4=
wl0_rts=2347
filter_web_url5=
crypto_5g=tkip
wan_ipv6_lease=0
sb/1/bw40po=0x0000
sb/1/devid=0x4347
wan_wins=
filter_web_url6=
wl_ifname=
warning_page_checked=0
qtdc0_ep=4
filter_web_url7=
http_enable=1
channel_5g=0
ntp_mode=auto
storage_group_name20=
ui_language=en
filter_web_url8=
wpa_psk_24g=
wl1_key1=
wl1_nmode_protection=auto
gn_http_port=51000
gn_bw_upstream=56
l2tp_pass=1
storage_group_name21=
media_server_name=Cisco03018
os_version=5.60.127.2901
filter_web_url9=
pppoe_username=
ppp_demand_pppoe=0
wl1_key2=
wan_speed=4
storage_group_name22=
usb/0xBD17/pa5ghw1a0=0x181f
sdram_phyctl=0x00000001
wl1_key3=
gn_wan_stat_record=0
qos_appname1=
storage_group_name23=
usb/0xBD17/pa5ghw1a1=0x17c5
wl0_wpa_gtk_rekey=3600
wl1_key4=
wl1_leddc=0x640000
qos_appname2=
storage_group_name24=
hnap_enable=1
ppp_get_srv=
radius_port_24g=1812
wl0_sta_retry_time=5
mac_clone_enable=0
qos_appname3=
storage_group_name25=
qos_appname4=
storage_group_name26=
usb/0xBD17/temps_hysteresis=5
hnap_devicename=Cisco03018
wl0_key=1
passphrase_24g=
gn_https_port=51001
wl0.1_macmode=disabled
filter_ipv6_cnt=0
wan_mtu=1500
qos_appname5=
nfs_master_enable=disabled
storage_group_name27=
wl0_active_mac=
qos_appname6=
storage_group_desc10=
device_view_type=0
wps_addER=0
wl_maclist=
emf_entry=
rate_mode=1
qos_appname7=
private_shares=
storage_group_desc11=
usb/0xBD17/ofdm5gpo=0x00000000
usb/0xBD17/boardflags=0x90000400
mfg_wait=on
wps_config_state_5g=0
wl1_infra=1
qos_appname8=
storage_group_desc12=
ip_conntrack_udp_timeout=65
mld_prefix=ff08::
et0phyaddr=30
console_loglevel=1
storage_group_desc13=
time_zone=-08 1 1
tmsss_enabled=0
wps_aplockdown_cap=1
ddns_mx=
storage_group_desc14=
charset=utf-8
switch_ipaddr=0.0.0.0
wl_wps_config_state=0
wan_auto_detect_result=UNKNOWN
wan_ipv6_dns=
storage_group_desc15=
open_disk_flag=0
wan_get_domain=
usb/0xBD17/tempoffset=0
wan_ipv6_rebind=0
storage_group_desc16=
storage_group_desc17=
wan_ifname=vlan2
net_mode_5g=mixed
storage_group_desc18=
upnp_max_age=180
adminui_warning_show=1
storage_group_desc19=
get_pa5gha2idxval=
usb/0xBD17/extpagain5g=3
sb/1/pdetrange2g=3
wep_gen_24g=
wl_radioids=
nas_login=admin:admin:adminff guest:guest:guestn
landevs=vlan1 wl0 wl1
wan_hostname=
wl0_dfs_postism=60
wl1_rate=0
gn_lan_ipv6_prefixlen=0
detect_lang=en
get_2g_country_code=
usb/0xBD17/boardtype=0xF52A
boot_hw_model=E3200
ppp_mtu=1500
wl_corerev=
wl0_radio=1
wl1_channels=36,40,44,48,149,153,157,161
log_type=ilog
wl0_nbw_cap=0
ddns_interval=60
wl0_max_channel=11
key_24g=1
wl0_bcn=100
wps_mode=enabled
manual_boot_nv=0
usb/0xBD17/triso5g=0
security_mode_0=disabled
wsc_ap_role=proxy
usb/0xBD17/phycal_tempdelta=0
filter_tod1=
ppp_static=0
wl0_hwaddr=
security_mode_1=disabled
usb/0xBD17/gpio0=pa_mask_low
filter_tod2=
wps_wer_mode=allow
wl1_net_reauth=36000
gn_lan_netmask=255.255.255.0
get_pa5gla2idxval=
filter_tod3=
ppp_demand_pptp=0
wan_ipv6_dhcp=on
sb/1/tssipos2g=1
ezc_version=2
filter_tod4=
wl0_wep_gen=
emf_enable=0
anonymous_samba=1
get_5g_country_code=
filter_tod5=
wl0_gmode_protection=auto
wk_mode=gateway
ddns_passwd_buf=
filter_tod6=
wl0_maclist=
nf_alg_sip=0
filter_tod7=
sdram_init=0x0419
filter_tod8=
filter_tod9=
wme_24g=on
sb/1/antswctl2g=1
lan_wins=
wl1_dfs_postism=60
wl_ap_isolate=0
FS_scan_folder_num=0
ftp_share_access_10=
lan_hwnames=
wps_modelnum=v1.0.03
ip_conntrack_udp_timeouts=65 180
wps_method=1
ftp_share_access_0=
usb/0xBD17/pa5glw0a0=0xFE8F
wl1_radius_ipaddr=
wl1_country=US/74
wl1_mrate=0
ftp_share_access_1=
usb/0xBD17/pa5glw0a1=0xFE6E
pppoe_demand=0
wl_wme_no_ack=off
closed_5g=0
wpa_psk_5g=
wl1_country_code=US/74
gn_bw_downstream=128
wan_ipv6_dns_secondary=
ftp_port=21
ftp_share_access_2=
ftp_share_access_3=
usb/0xBD17/pa5gw1a0=0x194e
gpio23=wombo_reset
filter_dport_grp10=
wl0_wps_config_state=0
wl0_radius_key=
wl0_radarargs_11a=5 4 4 100 0x2b0 0x2f0 0x0 0x0 8 500 4000 10 240000000
1000 3000000
wl1_gmode_protection=auto
wan_ipv6_ipaddr=
storage_group_desc20=
ftp_share_access_4=
usb/0xBD17/pa5gw1a1=0x198f
wl0_wme_ap_be=15 63 3 0 0 off off
ddns_username_buf=
storage_group_desc21=
lang_detected=0
ftp_share_access_5=
wl0_corerev=
wl0_nmcsidx=-1
gn_dhcp_start=100
storage_group_desc22=
ftp_share_access_6=
qtdc_pid=48407
wl1_rateset=default
ipv6_6to4_enable=0
storage_group_desc23=
ftp_share_access_7=
get_pa2ga0idxval=11 -428 8175 -1979
wl0_channel=0
wl1_gmode=1
nbw_cap_5g=1
wl1_ampdu=on
storage_group_desc24=
ftp_share_access_8=
usb/0xBD17/boardrev=0x1100
sb/1/ledbh0=11
wl0_wds_timeout=1
wps_device_name=Linksys E3200
wl1_unit=1
storage_group_desc25=
ftp_share_access_9=
usb/0xBD17/pa05glidx=0
sb/1/ledbh1=11
sb/1/maxp2ga0=0x64
wl1_wep_bit=64
wl0.1_bss_enabled=0
storage_group_desc26=
usb/0xBD17/venid=0x14E4
sb/1/ledbh2=11
sb/1/maxp2ga1=0x64
upnp_enable=1
wl0_wme_ap_bk=15 1023 7 0 0 off off
wl0_wps_mode=enabled
ipv6_multicast_pass=1
dr_setting=0
storage_group_desc27=
sb/1/ledbh3=11
akm_24g=
wl1_nband=1
wan_ipv6_prefix=
sb/1/cddpo=0x0000
wl1_wps_config_state=0
wl1_wme_sta_vi=7 15 2 6016 3008 off off
wl1_wps_mode=enabled
emf_uffp_entry=
wl_wsc_mode=enabled
log_show_type=ALL
filter_rule10=
wep_bit_24g=64
filter_ipv6_list=
ddns_status=
workgroup_or_domain=workgroup
dmz_src_any=1
wl1_nreqd=0
get_pa5ga0idxval=5 -381 6478 -1507
usb/0xBD17/mcs5ghpo0=0x3311
sb/1/rxchain=3
wl0_radarargs_11n=5 4 3 100 0x6b0 0x6f0 0x2c40 0x7f09 6 300 1200 25
200000000 1000 3000000
wl1_wps_crypto=aes
usb/0xBD17/mcs5ghpo1=0x8865
wl0_auth_mode=none
get_5g_country_code_index=0
boot_ver=v5.9
usb/0xBD17/mcs5ghpo2=0x3311
net_reauth_24g=36000
usb/0xBD17/mcs5ghpo3=0x8865
autofw_port0=
wps_mixedmode=0
wl1_wme_sta_vo=3 7 2 3264 1504 off off
language=EN
usb/0xBD17/pa15ghidx=1
usb/0xBD17/mcs5ghpo4=0x3311
boardnum=42
wl0_crypto=tkip
usb/0xBD17/mcs5ghpo5=0x8865
sb/1/antswitch=3
wl1_wds=
def_hwaddr=00:00:00:00:00:00
detect_charset=utf-8
usb/0xBD17/mcs5ghpo6=0x3311
auth_mode_24g=none
wl1_vlan_prio_mode=off
lan_ipv6_dhcp_renew=54000
usb/0xBD17/mcs5ghpo7=0x8865
usb/0xBD17/ofdm5glpo=0x00000000
usb/0xBD17/antswitch=3
wl1_wds_timeout=1
remote_samba=0
upnp_config=1
key1_5g=
wl_mac_filter=0
get_sn_index=1
filter_dport_grp1=
QoS_wan_ctl=1
ftp_characterset=0
startup_query_interval=31
partition_name_0=
filter_dport_grp2=
wl_radio_pwrsave_level=0

MacBook Air keeps rebooting during backup to TC

We got an MacBook Air and a MacBook Pro in our household and just got a Time Capsule to make it easy to back up both computers using time machine.
I'm not impressed. TC is slower than I expected for a 802.11n networked harddrive. I get a little over 1MB/sec when writing to the disk. Anyway, it took overnight to back up the Pro but subsequent backup were of course faster.
I never succeeded to back up my Air. It starts backing up. One or two hours later when I check the status the computer has rebooted and backup stopped. This happened 7-8 times. I tried turning off wifi and using an ethernet connection to the TC. It keeps rebooting.
Anyone knows what's happening here or could give me a pointer to how I can diagnose it further?
Haavard

I have the same problem, did you ever get an answer to this?

HT201240 Ive tried all the Command-s command-r and nothing is working. my macbook pro just keeps rebooting as normal. Ive forgotten my admin password, or have re-entered it incorrectly, and it won't let me downloads mavericks. No discs. HELP

Ive tried all the shortcuts to do without start up discs, but it just keeps rebooting as normal..... Help. I cant download mavericks, Ive changed my apple id, and that didnt make any difference......

Any reinstallation is not going to be successful if you have invalid node structure. You have bigger fish to fry here than worrying about DVD access.
Mr Simpson wrote:
The first step of this was to do a 'fsck -fy' and here it told me I had a 'disk0s2: I/0 error.' and 'Invalid node structure' and the volume check had failed.
You also mention that the 10.6 disc would read from the DVD but not allow you into Disk Utility? What happened when you tried to access it? Was it selectable and then didn't do anything?
We can't really narrow down whether it is the DVD or anything else at this time.
If you don't have a backup of the information it is probably toast if you cannot get Disk Utility to work. I would normaly suggest DIsk Warrior but that is a $79 gamble if you are not sure if the drive is working or not. It may be your last hope to recover whatever you can from the drive.
Also, what was the original OS installed on the machine before it crashed? Was it 10.6 or was it the 10.5.7 you mentioned?

7Th Generation Ipod Nano keeps rebooting

Hey everyone I just got my wife a nano for her birthday, but it keeps rebooting on songs. I cannot go for more than 5-10 minutes before the machine buzzes off and I see apple logo on my screen. Ive tried restoring, the secret menu by holding down home,power, and pressing the vol up and down on the 2nd black screen to check the nvram. passes. But still problems on numerous syncs and restores in-between, never in any other mode but playing mp3s..
she did not save my gift reciept nor the box, can we still get a working one without doing some sort of switch-a-roo at the store.
pretty bummed out here. Its was so sweet until it started zapping off and on.
-Jason

You're lucky MachRc... same situation here... 7th gen stuck in reboot infinite loop. Was xmas gift for wife 18 months ago... "Geniuses" at Apple fiddled with it for 5 minutes, said it's dead and only option is BUY a new one. Then told me I should have bought Apple Care... COME ON, if your products won't last 18 months then you really have a problem.
My solution, pulled out the 10 year old Sony Walkman mp3 player, charged it up and threw the ipod POS in the garbage... My lovely wife is now happily listening to her 10 YEAR OLD Sony product without any problems.
So long Apple!

K9A2 Neo keeps rebooting itself

I just had my motherboard and graphics card replaced but the new system keeps rebooting itself. It can happen even if if the computer is just idling and I'm not doing anything with it but it happens a lot more frequently if I play certain games. Windows was not reinstalled after replacing these two cards. I don't know if it's of any significance but when I boot the machine the board beeps 5 or 6 times, instead of the 1 time I'm used to. More often than not the unwanted reboot fails and ends in a blank screen but initial booting of the machine always succeeds.
I'm fairly green in these matters and would be really grateful if someone could point me in the right direction on this one.

Test each one memory stick alone with >>Memtest86<< , use the 1st DIMM slot close to CPU socket.
For details you can take a look here: https://forum-en.msi.com/index.php?topic=103598.msg760534#msg760534
What PSU you use? {List brand and details {amperes per each line}, look for them over PSU sticker. Example in my signature}
Also check CPU for overheating.

865PE Neo2-V Conflict, keeps rebooting.....

Hi,
I have recently bought a MSI 865PE Neo2-V mainboard but it keeps rebooting all the time at intalling windows xp.
One time i did manage to install winxp but after installing other software the computer reboots.
I doublechecked the CPU and Memory.
So i think it is the Bios settings. Can anyone help me out with this problem?
This is my system:
MSI 865PE Neo2-V
Intel Pentium 4 3.0Ghz
160 GB WD
512 MB DDR Twinmos Memory
350 Watt PSU
Sapphire RADEON 9250

Quote from: fafner on 08-March-05, 22:55:30
ok. let us know what happens wnen you try the different psu.
Hi again
I tried an other PSU and it works!! I can't thank all of you enough.
I think it was my PSU that was not compatible with the mobo or that the PSU was corrupt.
Anyways PROBLEM SOLVED!!!
Thank You.

After upgrade to mavericks: time machine keeps asking for my back up disk and won't open unless i plug in the disk. any solutions?

after upgrade to mavericks: time machine keeps asking for my back up disk and won't open unless i plug in the disk. any solutions?
before the upgrade, i could open time machine without the need for having the back up disk plugged in.

Ok. I got it to work, sort of....
As I mentioned before I tried the "disk password" and the "Time capsule Password" options to see if I can start the back up again or start a new backup. Neither worked. So I tried the firmware down grade, but like you said that did not work. I then decided to try the "Account password" option and I have never used this option before becasue it states that if there is data on the drive it would not be acessable after creating an account. Since I wiped out the disk that was nno problem. When I created the new account and choose the drive it asked for the user name and password. I entered the info for the new account I just created(FYI this has nothing to do with your login username and password), bingo! It worked!
Now I have two partitions on the TC disk. The old one and now the new account. I am guessing this is to be used if I have multiple computers, which I don't.
I any case, I am going to wipe out everything again and try again to do a backup the way I had it before.

I am trying to update my time machine backup on time capsule, but time machine keeps trying to create an entirely new backup (evidenced by the 200GB backup size). How can I get time machine to modify my old backup rather than create a new one?

I am trying to update my time machine backup on time capsule, but time machine keeps trying to create an entirely new backup (evidenced by the 200GB backup size). How can I get time machine to modify my old backup rather than create a new one?

It must have found the old backup corrupt.. so you will more than likely have little choice. You can archive off the old backup if it is still useful.
You can also verify it. See A5 http://pondini.org/TM/Troubleshooting.html
He also has some info on this problem. eg C13.

Mac pro keeps rebooting

My Mac Pro 2.1 Keeps rebooting ramdomly. It seems to be more common when editing video.
Any ideas anybody?
Thanks in advance.

Sorry for the slow reply.
My Mac Pro 2.1 screens go black and instantly reboots, sometimes it keeps rebooting until i hold the power button. I have reset pram,smc,renewed permissions and checked hard discs.
I am booting from a drive with lion 10.7.3. It also happens when I am booted from another drive running Snow Leopard.
I have also removed 4 gig of the 8 gig of ram and tried different configs of ram.
I have also disconnected everything except the keyboard, mouse and 2 monitors.
It is driving me bonkers because I cannot trust the mac Pro and I often lose work because it suddenly reboots.
Any suggestions anyone.

Laserjet pro MFP M176n keeps rebooting

Hi,
I have a Color laserjet Pro MFP M176n printer. It ha snot been used for sometime.2 weeks ago when I printed something it had constant paper jam. I open the front door to remove the jam problem was not solved, I removed the ink cartridge to see if there was any piece of paper .Switch the apparatus off and when i switch it on again it just wnt switch on and now it just keep rebooting and wont display anything.
I would liek to know how to solve this problem or if the printer has to be thrown out.
Regards

Hi @widadr,
I see that you are experiencing issues with the printer constantly rebooting. I will certainly do my best to help you.
Temporarily disconnect any cables from the printer, except the power cord, just to make sure there isn't any interference for the next few steps.
I would do a hard reset to see if that will resolve the issue.
Leave the printer on and unplug the power cable from the printer and wall outlet for 60 seconds.
Then reconnect the power cable to the printer and wall outlet rather than a surge protector.
This ensures the printer is receiving full power and may help this situation.
Perform a power drain by disconnecting the power cord from the back of the printer and keeping the power button pressed for 30 seconds and in case of a power switch keep the switch in ON position for 30 seconds before reconnecting the power chord.
Try and update the printer's firmware by a USB connection if the issue persists. Software and Drivers.
I will send you another step to try in a private message.
In the forum beside your handle name just click on the envelope to view it.
How is the printer connected? (USB/Ethernet)
What operating system are you using? How to Find the Windows Edition and Version on Your Computer.
If you appreciate my efforts, please click the Thumbs up button below.
If there is anything else I can help you with, just let me know. Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Sun OS 5.8 Panic machine keeps rebooting

Similar Messages

Maybe you are looking for