Sun StorageTek Data Services software

Hi All ,
I wanted to know where can I get documents related Sun StorageTek Data Snapshot, Volume
Copy and Data Replicator software.(Admin Guide ) .?
Thanks in advance .......

Hi defunkt0r
I don't know if there is a so called "whitepaper" best practice guide for what your wanting to do , but here is what I would do
From what I understand, it should be as simple as unmounting the volume on the old host, moving the HBAs to the new box w/ correct drivers etc, connecting the >6140 up to the new box, bringing up the data host machine and importing the disk/mounting in the new box.This part is correct , don't forget you'll also need to modify your switch zoning to reflect your new WWN's of your HBA's.
You'll also need to login into CAM and make sure those new "WWN's" of those HBA's are seen , once you can confirm the new WWN's in CAM , Don't forget to set up your host initiator correctly i.e Windows , Linux , vmware.
Once these steps are done you'll be good to go and power up your host.
Good luck
David

Similar Messages

Sun StorageTek Data Replicator. prerequisites

Hello All
MY client is looking for a SAN to SAN replication solution between there Primary & DR Site, we are proposing 2 x Storage Tek 6140 with Sun StorageTek Data Replicator Software
kindly let me know what type of link is required to get 0% latency. They want to get replicated data at both end without any delay
Kindly help in this regards
Ali Jafri

Hi defunkt0r
I don't know if there is a so called "whitepaper" best practice guide for what your wanting to do , but here is what I would do
From what I understand, it should be as simple as unmounting the volume on the old host, moving the HBAs to the new box w/ correct drivers etc, connecting the >6140 up to the new box, bringing up the data host machine and importing the disk/mounting in the new box.This part is correct , don't forget you'll also need to modify your switch zoning to reflect your new WWN's of your HBA's.
You'll also need to login into CAM and make sure those new "WWN's" of those HBA's are seen , once you can confirm the new WWN's in CAM , Don't forget to set up your host initiator correctly i.e Windows , Linux , vmware.
Once these steps are done you'll be good to go and power up your host.
Good luck
David

SUN cluster data service for JCAPS 513

Hi,
I am trying to setup scalable data service for logical host (JCAPS 513) using SUN cluster. Did anybody tried in the past or is it feasible?
The requirement is to run the JCAPS simulateneously on two servers hosted across two data centers geographically apart.
Regards
Srinivas

support.oracle.com
just create a login, you might need a serial number or a support identifier..
.7/M.

I bought new i phone 5 3 days back, after that asked for new update which is 6.1.4, after updating my iphone i am not able to use cellular data services. I called up data provider, they says its the problem with new software update. There is no option add

I bought new i phone 5 3 days back, after that asked for new update which is 6.1.4, after updating my iphone i am not able to use cellular data services. I called up data provider, they says its the problem with new software update. There is no option add APN. Now when i switch to safari its showing you are not subscribed for cellular data. But I am able to use data on other phone.
Will you please help me in this regard?
Another issue, since i bought my new iphone there is dust inside back main camera.
Your advises are highly appreciated.

Hey Shaiju isac,
I'd take a look at the following article, it'll guide you though steps to you troubleshoot cellular data issues on your iPhone:
iPhone: Troubleshooting a cellular data connection
http://support.apple.com/kb/ts3780
Cheers,
David

Try NineSYNC, Internet Data Synchronization & Mapping Web Service Software

Those who are learning or pros in web service technology, try the software named NineSYNC, an internet data synchronization and mapping web service, which really running at http://www.ninestep.com/services/ninesync/NineSYNC. You can go to the Jence Incorporated (NineSTEP) web site http://www.jence.com or http://www.ninesync.com and load the NineSYNC client. You can also load the trial version of the web service software.
NineSYNC is a real web service and its big. And it does what its supposed to do. I have tried synchronizing data from Mysql to Sql Server and it was so quick with NineSYNC. I also synchronize files with NineSYNC on a daily basis. All you have to do is set the software up and it will synchronize periodically.
Nice cool way to do things and the future of web services technology.
Burd.

Burd, It's a nice program. I haven't found anything like this before and it works quite good. Thanks for sharing the informaiton. I would suggest anybody to take a look at this SW who are involved in data synchronization and mapping process.

Running "Flex test drive" - Got error while attempting to connect to data service

Hi,
I'm a Flex / Flash builder beginner. I downloaded the 60 days evaluation, and started to run the "Flex test drive" :
http://www.adobe.com/devnet/flex/testdrive.html
My configuration :
XP SP3 PRO french edition
Tomcat 6.0
My local Eclipse :eclipse-jee-helios-SR2-win32 (but also got the issue on the Flash Builder Eclipse, which version is 3.4.0 (Generation ID M20090211-1700)
Flash Builder 4 with Eclipse plug-in
All on same PC
The Test Drive proposes examples in three technologies : Cold Fusion, PHP and Java. I'm doing the Java examples.
Installation of Flash Builder, as well as step 1 of the Test Drive (Build the user interface) went fine. I could run the project, which at the end of step 1 correctly displayed the UI in my browser.
Only one problem, I don't know if it is relevant for the rest of this post : I first got an error, saying that ports 8080, 8005 and 8009, requested by Tomcat, where used. After a short Google search, I fixed it by changing these ports to 8081, 8006, and 8010, in the Tomcat 6.0\conf\server.xml file.
The Test drive second step is "Connect to data". I found some discrepancies between the Test Drive doc, and what is displayed in Flash Builder. The Test Drive says :
"Use the Data menu and the Service Wizard to create a service for your application server. For ColdFusion and Java, specify the service file you put on your application server earlier (see Figure 9 for a PHP example). For Java, select the No password required check box, select the employeeService destination, and change the service package to services.employeeservice."
--> But there is no "No password required check box".
Also, when running the "Connect to data/service..." wizard, it was not at first completely clear what to choose. The proposed choices were :
BlazeDS
ColdFusion
HTTP
LCDS
PHP
Web Service
XML
Since all others choices, when tried, declared to be unconsistent with my project's server type, I finally selected "Web Service".
In the next wizard's form, according to the Test Drive indications, I specified the URI of my EmployeeService class : C:\Program Files\Apache Software Foundation\Tomcat 6.0\webapps\testdrive\WEB-INF\classes\services\EmployeeService.class
That defined correctly the other fields.
But when pressing the "Next >" button, Flash Builder issued the following error message :
English translation : Unable to extract operations and entities from specified WSDL. Reason : an error occured while instrospecting the service.
And the full error text is :
An error occured while instrospecting the service. WSDLException: faultCode=PARSER_ERROR: Problem parsing 'file:/C:/Program%20Files/Apache%20Software%20Foundation/Tomcat%206.0/webapps/testdrive/W EB-INF/classes/services/EmployeeService.class'.: com.sun.org.apache.xerces.internal.impl.io.MalformedByteSequenceException: Invalid byte 2 of 2-byte UTF-8 sequence.
It is usually relatively easy to find fixes through Google searches, but this time, it didn't work. So here I am, expecting a bunch of wise answers from all the nice Flex / FB gurus that I'm sure haunt this forum .
Thanks and best regards.
Marc.

For those who would have the same problem, here is how I could eventually fix it.
Since the Flex Test Drive is sometimes out of sync with flash builder 4, I recreated a project using other help pages on Adobe site :
Entry point :
http://help.adobe.com/en_US/Flex/4.0/AccessingData/WSbde04e3d3e6474c4-668f02f4120d422cf08- 7ffd.html
As suggested, I used the New Project wizard to create a new project, with :
Application server type : J2EE
Check the radio button "Use remote object access service : BlazeDS"
Then, as indicated in following pages (section "Accessing BlazeDS")... :
file:///C:/Mes%20documents%20C/Commun/Developpement/Documentation/HT-Tracks/AccessingData/ help.adobe.com/en_US/Flex/4.0/AccessingData/WSbde04e3d3e6474c4-668f02f4120d422cf08-7ffe.ht ml#WSbde04e3d3e6474c4-19a3f0e0122be55e1b7-8000
...I selected the "Data / Connect to Data/Services..." menu option, which started the Data/service connection wizard.
There, I selected a BlazeDS (and not Web Services) service type, and everything went fine.
Suggestion to adobe staff : maybe it would be useful to update the Flex Test Drive to reflect Flash Builder 4 ?
Very nice product anyway, so far, congratulations...
Rgds
Marc.

Unable to Find SBOP DATA SERVICES 4

Hello ,
I am unable to find the SBOP DATA SERVICES 4.0 software on SMP, does this mean that my S user ID or my company doesn't have a valid license for this version or the product is in ramp up (I have checked the ramp up release too but unable to find 4.0 version thr) however I am able to download the XI3.2.
Regards
Saurabh Mishra

Yes, it is in Ramp-up and you need to be authorized to be able to download the software.

Data Services wizard not creating service

I am having huge problems with the Data Services wizard.
I am using Flash Builder 4.6 on a Mac (10.7.2).
Over the last year I have been working on a couple of proof of concept projects and now want to start work on a production version starting from scratch in a new project.
The Data Services wizard has worked fine for me in the past, but now I am having serious problems.
The first problem is the Data/Services window does not update when I create a new service with the wizard. (I am connecting to the Zenfolio Web Service.) If have to close the project and open it before I see the new service in the Data/Services window.
While this problem is more an inconvenience, more seriously the wizard does not create either the "services" folder or the "valueObjects" folder as it did in the past.
Now if I right click on a method in the service and select "Create Service Call", it creates the Call Responder but not the call itself.
The relevant log entry starts with
!ENTRY com.adobe.flexbuilder.dcrad 4 1 2012-01-12 22:39:20.962
!MESSAGE Component type services.zfapi.Zfapi not found.
If I create a "services" folder and copy the zfapi package from one of my previous projects, all works fine.
This probably gives me a workaround - although I haven't tested this to any extent yet.
It is very strange and worrying behaviour though.
regards
Chris

OK, here are the log entries created when I try to create the service:
!ENTRY com.adobe.flexbuilder.dcrad 4 1 2012-01-19 22:16:33.970
!MESSAGE
!STACK 0
java.lang.reflect.InvocationTargetException
          at org.eclipse.jface.operation.ModalContext.runInCurrentThread(ModalContext.java:479)
          at org.eclipse.jface.operation.ModalContext.run(ModalContext.java:372)
          at org.eclipse.jface.dialogs.ProgressMonitorDialog.run(ProgressMonitorDialog.java:507)
          at com.adobe.flexbuilder.dcrad.core.internal.ServicesManager.addServices(ServicesManager.jav a:476)
          at com.adobe.flexbuilder.dcrad.views.ServiceExplorerView$1.handleEvent(ServiceExplorerView.j ava:536)
          at org.eclipse.swt.widgets.EventTable.sendEvent(EventTable.java:84)
          at org.eclipse.swt.widgets.Display.sendEvent(Display.java:4128)
          at org.eclipse.swt.widgets.Widget.sendEvent(Widget.java:1457)
          at org.eclipse.swt.widgets.Widget.sendEvent(Widget.java:1480)
          at org.eclipse.swt.widgets.Widget.sendSelectionEvent(Widget.java:1530)
          at org.eclipse.swt.widgets.Link.textView_clickOnLink_atIndex(Link.java:117)
          at org.eclipse.swt.widgets.Display.windowProc(Display.java:5781)
          at org.eclipse.swt.internal.cocoa.OS.objc_msgSendSuper(Native Method)
          at org.eclipse.swt.widgets.Widget.callSuper(Widget.java:220)
          at org.eclipse.swt.widgets.Widget.mouseDownSuper(Widget.java:1092)
          at org.eclipse.swt.widgets.Widget.mouseDown(Widget.java:1084)
          at org.eclipse.swt.widgets.Control.mouseDown(Control.java:2519)
          at org.eclipse.swt.widgets.Display.windowProc(Display.java:5471)
          at org.eclipse.swt.internal.cocoa.OS.objc_msgSendSuper(Native Method)
          at org.eclipse.swt.widgets.Widget.callSuper(Widget.java:220)
          at org.eclipse.swt.widgets.Widget.windowSendEvent(Widget.java:2092)
          at org.eclipse.swt.widgets.Shell.windowSendEvent(Shell.java:2252)
          at org.eclipse.swt.widgets.Display.windowProc(Display.java:5535)
          at org.eclipse.swt.internal.cocoa.OS.objc_msgSendSuper(Native Method)
          at org.eclipse.swt.widgets.Display.applicationSendEvent(Display.java:4989)
          at org.eclipse.swt.widgets.Display.applicationProc(Display.java:5138)
          at org.eclipse.swt.internal.cocoa.OS.objc_msgSend(Native Method)
          at org.eclipse.swt.internal.cocoa.NSApplication.sendEvent(NSApplication.java:128)
          at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3610)
          at org.eclipse.ui.internal.Workbench.runEventLoop(Workbench.java:2696)
          at org.eclipse.ui.internal.Workbench.runUI(Workbench.java:2660)
          at org.eclipse.ui.internal.Workbench.access$4(Workbench.java:2494)
          at org.eclipse.ui.internal.Workbench$7.run(Workbench.java:674)
          at org.eclipse.core.databinding.observable.Realm.runWithDefault(Realm.java:332)
          at org.eclipse.ui.internal.Workbench.createAndRunWorkbench(Workbench.java:667)
          at org.eclipse.ui.PlatformUI.createAndRunWorkbench(PlatformUI.java:149)
          at com.adobe.flexbuilder.standalone.FlashBuilderApplication.start(FlashBuilderApplication.ja va:108)
          at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandle.java:196)
          at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runApplication(EclipseAppLau ncher.java:110)
          at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(EclipseAppLauncher.jav a:79)
          at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:344)
          at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:179)
          at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
          at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
          at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
          at java.lang.reflect.Method.invoke(Method.java:597)
          at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:622)
          at org.eclipse.equinox.launcher.Main.basicRun(Main.java:577)
          at org.eclipse.equinox.launcher.Main.run(Main.java:1410)
Caused by: java.lang.NoClassDefFoundError: org/apache/log4j/Priority
          at freemarker.log.Log4JLoggerFactory.getLogger(Log4JLoggerFactory.java:65)
          at freemarker.log.Logger.getLogger(Logger.java:255)
          at freemarker.template.utility.SecurityUtilities.<clinit>(SecurityUtilities.java:67)
          at freemarker.ext.beans.BeansWrapper.<clinit>(BeansWrapper.java:147)
          at freemarker.template.ObjectWrapper.<clinit>(ObjectWrapper.java:69)
          at freemarker.core.Configurable.<init>(Configurable.java:132)
          at freemarker.template.Configuration.<init>(Configuration.java:109)
          at freemarker.template.Configuration.<clinit>(Configuration.java:96)
          at fiber.gen.freemarker.FreemarkerModelGenerator.buildFreemarkerConfiguration(FreemarkerMode lGenerator.java:328)
          at fiber.gen.freemarker.FreemarkerModelGenerator.<init>(FreemarkerModelGenerator.java:85)
          at fiber.gen.freemarker.FreemarkerStructuredTypeGenerator.<init>(FreemarkerStructuredTypeGen erator.java:62)
          at fiber.gen.as.ASClassGenerator.<init>(ASClassGenerator.java:84)
          at fiber.gen.as.vo.SuperGenerator.<init>(SuperGenerator.java:53)
          at fiber.gen.as.vo.ASValueObjectGenerator$2.<init>(ASValueObjectGenerator.java:225)
          at fiber.gen.as.vo.ASValueObjectGenerator.getBaseClassGenerator(ASValueObjectGenerator.java: 222)
          at fiber.gen.as.vo.ASValueObjectGenerator.getTemplateNames(ASValueObjectGenerator.java:392)
          at fiber.gen.as.ASGenerator.getTemplateNames(ASGenerator.java:465)
          at com.adobe.model.core.generators.wrapper.CodeGenerationUtils.getTemplateResources(Unknown Source)
          at com.adobe.model.core.generators.wrapper.CodeGenerationWrapper.getTemplateResourcesForGene rator(Unknown Source)
          at com.adobe.model.core.generators.wrapper.CodeGenerationWrapper.generateCodeForGenerator(Un known Source)
          at com.adobe.model.core.generators.wrapper.CodeGenerationWrapper.internalGenerateAllCodeForM odel(Unknown Source)
          at com.adobe.model.core.generators.wrapper.CodeGenerationWrapper$2.run(Unknown Source)
          at com.adobe.model.core.generators.wrapper.CodeGenerationWrapper.generateAllCodeForModel(Unk nown Source)
          at com.adobe.flexbuilder.dcrad.core.generation.ASVOGenerator.generate(ASVOGenerator.java:78)
          at com.adobe.flexbuilder.dcrad.core.internal.ServicesManager.generateVO(ServicesManager.java :538)
          at com.adobe.flexbuilder.dcrad.core.internal.ServicesManager.add(ServicesManager.java:403)
          at com.adobe.flexbuilder.dcrad.core.internal.ServicesManager.access$11(ServicesManager.java: 356)
          at com.adobe.flexbuilder.dcrad.core.internal.ServicesManager$1.run(ServicesManager.java:484)
          at org.eclipse.jface.operation.ModalContext.runInCurrentThread(ModalContext.java:464)
          ... 48 more
Caused by: java.lang.ClassNotFoundException: org.apache.log4j.Priority
          at org.eclipse.osgi.internal.loader.BundleLoader.findClassInternal(BundleLoader.java:513)
          at org.eclipse.osgi.internal.loader.BundleLoader.findClass(BundleLoader.java:429)
          at org.eclipse.osgi.internal.loader.BundleLoader.findClass(BundleLoader.java:417)
          at org.eclipse.osgi.internal.baseadaptor.DefaultClassLoader.loadClass(DefaultClassLoader.jav a:107)
          at java.lang.ClassLoader.loadClass(ClassLoader.java:247)
          ... 77 more
Root exception:
java.lang.NoClassDefFoundError: org/apache/log4j/Priority
          at freemarker.log.Log4JLoggerFactory.getLogger(Log4JLoggerFactory.java:65)
          at freemarker.log.Logger.getLogger(Logger.java:255)
          at freemarker.template.utility.SecurityUtilities.<clinit>(SecurityUtilities.java:67)
          at freemarker.ext.beans.BeansWrapper.<clinit>(BeansWrapper.java:147)
          at freemarker.template.ObjectWrapper.<clinit>(ObjectWrapper.java:69)
          at freemarker.core.Configurable.<init>(Configurable.java:132)
          at freemarker.template.Configuration.<init>(Configuration.java:109)
          at freemarker.template.Configuration.<clinit>(Configuration.java:96)
          at fiber.gen.freemarker.FreemarkerModelGenerator.buildFreemarkerConfiguration(FreemarkerMode lGenerator.java:328)
          at fiber.gen.freemarker.FreemarkerModelGenerator.<init>(FreemarkerModelGenerator.java:85)
          at fiber.gen.freemarker.FreemarkerStructuredTypeGenerator.<init>(FreemarkerStructuredTypeGen erator.java:62)
          at fiber.gen.as.ASClassGenerator.<init>(ASClassGenerator.java:84)
          at fiber.gen.as.vo.SuperGenerator.<init>(SuperGenerator.java:53)
          at fiber.gen.as.vo.ASValueObjectGenerator$2.<init>(ASValueObjectGenerator.java:225)
          at fiber.gen.as.vo.ASValueObjectGenerator.getBaseClassGenerator(ASValueObjectGenerator.java: 222)
          at fiber.gen.as.vo.ASValueObjectGenerator.getTemplateNames(ASValueObjectGenerator.java:392)
          at fiber.gen.as.ASGenerator.getTemplateNames(ASGenerator.java:465)
          at com.adobe.model.core.generators.wrapper.CodeGenerationUtils.getTemplateResources(Unknown Source)
          at com.adobe.model.core.generators.wrapper.CodeGenerationWrapper.getTemplateResourcesForGene rator(Unknown Source)
          at com.adobe.model.core.generators.wrapper.CodeGenerationWrapper.generateCodeForGenerator(Un known Source)
          at com.adobe.model.core.generators.wrapper.CodeGenerationWrapper.internalGenerateAllCodeForM odel(Unknown Source)
          at com.adobe.model.core.generators.wrapper.CodeGenerationWrapper$2.run(Unknown Source)
          at com.adobe.model.core.generators.wrapper.CodeGenerationWrapper.generateAllCodeForModel(Unk nown Source)
          at com.adobe.flexbuilder.dcrad.core.generation.ASVOGenerator.generate(ASVOGenerator.java:78)
          at com.adobe.flexbuilder.dcrad.core.internal.ServicesManager.generateVO(ServicesManager.java :538)
          at com.adobe.flexbuilder.dcrad.core.internal.ServicesManager.add(ServicesManager.java:403)
          at com.adobe.flexbuilder.dcrad.core.internal.ServicesManager.access$11(ServicesManager.java: 356)
          at com.adobe.flexbuilder.dcrad.core.internal.ServicesManager$1.run(ServicesManager.java:484)
          at org.eclipse.jface.operation.ModalContext.runInCurrentThread(ModalContext.java:464)
          at org.eclipse.jface.operation.ModalContext.run(ModalContext.java:372)
          at org.eclipse.jface.dialogs.ProgressMonitorDialog.run(ProgressMonitorDialog.java:507)
          at com.adobe.flexbuilder.dcrad.core.internal.ServicesManager.addServices(ServicesManager.jav a:476)
          at com.adobe.flexbuilder.dcrad.views.ServiceExplorerView$1.handleEvent(ServiceExplorerView.j ava:536)
          at org.eclipse.swt.widgets.EventTable.sendEvent(EventTable.java:84)
          at org.eclipse.swt.widgets.Display.sendEvent(Display.java:4128)
          at org.eclipse.swt.widgets.Widget.sendEvent(Widget.java:1457)
          at org.eclipse.swt.widgets.Widget.sendEvent(Widget.java:1480)
          at org.eclipse.swt.widgets.Widget.sendSelectionEvent(Widget.java:1530)
          at org.eclipse.swt.widgets.Link.textView_clickOnLink_atIndex(Link.java:117)
          at org.eclipse.swt.widgets.Display.windowProc(Display.java:5781)
          at org.eclipse.swt.internal.cocoa.OS.objc_msgSendSuper(Native Method)
          at org.eclipse.swt.widgets.Widget.callSuper(Widget.java:220)
          at org.eclipse.swt.widgets.Widget.mouseDownSuper(Widget.java:1092)
          at org.eclipse.swt.widgets.Widget.mouseDown(Widget.java:1084)
          at org.eclipse.swt.widgets.Control.mouseDown(Control.java:2519)
          at org.eclipse.swt.widgets.Display.windowProc(Display.java:5471)
          at org.eclipse.swt.internal.cocoa.OS.objc_msgSendSuper(Native Method)
          at org.eclipse.swt.widgets.Widget.callSuper(Widget.java:220)
          at org.eclipse.swt.widgets.Widget.windowSendEvent(Widget.java:2092)
          at org.eclipse.swt.widgets.Shell.windowSendEvent(Shell.java:2252)
          at org.eclipse.swt.widgets.Display.windowProc(Display.java:5535)
          at org.eclipse.swt.internal.cocoa.OS.objc_msgSendSuper(Native Method)
          at org.eclipse.swt.widgets.Display.applicationSendEvent(Display.java:4989)
          at org.eclipse.swt.widgets.Display.applicationProc(Display.java:5138)
          at org.eclipse.swt.internal.cocoa.OS.objc_msgSend(Native Method)
          at org.eclipse.swt.internal.cocoa.NSApplication.sendEvent(NSApplication.java:128)
          at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3610)
          at org.eclipse.ui.internal.Workbench.runEventLoop(Workbench.java:2696)
          at org.eclipse.ui.internal.Workbench.runUI(Workbench.java:2660)
          at org.eclipse.ui.internal.Workbench.access$4(Workbench.java:2494)
          at org.eclipse.ui.internal.Workbench$7.run(Workbench.java:674)
          at org.eclipse.core.databinding.observable.Realm.runWithDefault(Realm.java:332)
          at org.eclipse.ui.internal.Workbench.createAndRunWorkbench(Workbench.java:667)
          at org.eclipse.ui.PlatformUI.createAndRunWorkbench(PlatformUI.java:149)
          at com.adobe.flexbuilder.standalone.FlashBuilderApplication.start(FlashBuilderApplication.ja va:108)
          at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandle.java:196)
          at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runApplication(EclipseAppLau ncher.java:110)
          at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(EclipseAppLauncher.jav a:79)
          at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:344)
          at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:179)
          at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
          at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
          at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
          at java.lang.reflect.Method.invoke(Method.java:597)
          at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:622)
          at org.eclipse.equinox.launcher.Main.basicRun(Main.java:577)
          at org.eclipse.equinox.launcher.Main.run(Main.java:1410)
Caused by: java.lang.ClassNotFoundException: org.apache.log4j.Priority
          at org.eclipse.osgi.internal.loader.BundleLoader.findClassInternal(BundleLoader.java:513)
          at org.eclipse.osgi.internal.loader.BundleLoader.findClass(BundleLoader.java:429)
          at org.eclipse.osgi.internal.loader.BundleLoader.findClass(BundleLoader.java:417)
          at org.eclipse.osgi.internal.baseadaptor.DefaultClassLoader.loadClass(DefaultClassLoader.jav a:107)
          at java.lang.ClassLoader.loadClass(ClassLoader.java:247)
          ... 77 more

Data Services- The job server you selected is not working

Long Text:
After logging in to the Data Services designer,when try to run a job it shows error -The job server you selected is not working
Latest Software version -BODS 4.0 SP2
Reproduce Steps:
1. Double click on the Project from repository, it will display the project in Project area.
2. After that it will display all the jobs under the project.
3.Right click on the job and try to execute, then it will display the "Execution Properties" windows.
Here the we can the default Job Server has been selected.
4. Try to click ok to execute the job and then we get the error-"The job server you selected is not working"

Hi
Please contact your Data services administrator to check on the server why the job server is not working.
There might be several issues like connectivity with the repository, access details , mapping in the management console etc.
And let us know the exact issue.
Regards
Puneet

Master Data Services not available under shared feature while installing SQL server 2012

Hi,
I am trying to install Master Data Services but do not see the option to select MDS under the shared features when going through the SQL server 2012 installation. I have the SQL server 2012 SP1 (64 bit) install files. I have also installed SP2. I havent
found anything online about the issue.
Can someone please advise?
I have a screenshot of the installation screen which I will attach as soon as I am able to get my account verified. Thanks!

Hi Revees,
This might be a very naïve and also out of the original scope of the thread question.
We are thinking of going with the developer edition. We have 2/3 developers and some other testers and business users.
1) I understand that we need a developer license for each developer. But would we need a license for the business user. Can they have a sort of read access to the dbs?
2) If a developer has MSDN subscription, Would they need to purchase the license too assuming we purchase the developer edition of the software (and not download it using the MSDN subscription)?
Thanks for your assistance!

Web services Connection_Operations.Logon call fails on Data Services 4.0

Hello,
We recently installed Data Services 4.0. We have a custom Java app which makes use of the web services interface. We had previously used Axis to generate the java class. With DS 4, it looks like the Logon method did change as it now requires the cms system and authentication. We manually updated the java classes to includes these, which has been our general approach in the past for newer releases. However DS 4 uses Axis2 and I'm not sure that this approach would work.
My problem is that the "Logon" call fails with very little details.
In viewing both the webadmin.log and WebService.log it only reports the following:
11/02/2011 18:42:17 [ SEVERE ] Logon failed. Error: null
I understand that I can control the logging detail . The Integrator Guide for DS 4.0, has the following instruction, yet there is no log4j.properties file on my system?
"To control the level of detail in the webadmin.log file, you must edit the log4j.properties file.
The properties file is located in:
LINK_DIR\ext\webserver\webapps\acta_web_admin\WEB-INF
To obtain a debug trace of events, change the log level from the default of INFO to DEBUG. For example,
log4j.rootLogger=DEBUG, A"
Any advise would be greatly appreciated
Thanks

Hello,
Unfortunately, stdout.log below doesn't show anything possibly due to some mis-configuaration of log4j.properties. In my previous post I requested info on which log4j.properties should be modified as the documentation in the DS 4.0 Integrator's guide mentions a none-existent path?
log4j:WARN No appenders could be found for logger (org.apache.commons.digester.Digester).
log4j:WARN Please initialize the log4j system properly.
log4j:WARN No appenders could be found for logger (com.sun.faces.config.ConfigureListener).
log4j:WARN Please initialize the log4j system properly.
log4j:WARN No appenders could be found for logger (org.apache.commons.digester.Digester).
log4j:WARN Please initialize the log4j system properly.
log4j:WARN No appenders could be found for logger (com.sun.faces.config.ConfigureListener).
log4j:WARN Please initialize the log4j system properly.
com.businessobjects.webpath.rebean3ws.Activator
log4j:WARN No appenders could be found for logger (org.apache.commons.digester.Digester).
log4j:WARN Please initialize the log4j system properly.
null

IPhone 5 cellular data services failing

ISSUE/SYMPTOMS: iPhone 5 ONLY: Cellular Data stops intermittingly, cellular data locks up without warning, Wi-Fi data connection not working on occasion, iCloud contacts, calendar and reminders not updating, Find My Phone not working, mail or Internet not available or server time-outs. No error messages though. All of these are symptoms of no data service. Problems seem to be related to iPhone 5 failing to switch between LTE and 4G or 3G data services on AT&T.
My iPhone 5 32GB AT&T version (iOS 6.0.2) along with my clients and family using iPhone 5 in the state of Oklahoma are having this issue on their AT&T iPhone 5's: no cellular data connection re-established if at anytime the LTE connection is lost or weak. As with iPhone's prior to iPhone 5, the iPhone 5 is supposed to drop down to the next tier of data service and re-connect to cellular data service when the higher speed cellular data service is not available. Apparently this is not working well on the iPhone 5.
What led me to research this LTE issue was that my iPhone was not syncing on iCloud with contacts, calendars and reminders with my other iOS devices. Other times this issue became apparent was when iMessage quit sending and receiving until I would reboot my iPhone (sometimes it would finally send the message as a “text message”). When I had these problems I also found out I was not getting any cellular data service for Internet browsing, mail, Maps, Find My iPhone, etc. This would happen without notice. In other words I would not receive any notice or error message that data service had stopped other than the fact I was not receiving any mail, iMessages, or iCloud sync updates. My only resolution was to reset or reboot my iPhone several times a day, and that would resolve it about 70% of the time.
I have talked to Apple Support on 2-3 occasions in the last week and AT&T Support twice in the last 2 days. If it is really true, only the AT&T Technical Support Advisor informed me of a nationwide issue relating to iPhone 5 and LTE: iPhone 5's are not re-connecting to 4G or 3G cellular data service once the LTE data connection is lost or dropped... the voice calls continue to work, but cellular data service fails and stays locked up without an error message until the customer reboots the iPhone.
Obviously this is very unacceptable. We depend on these data services and at minimum need to know when it stops working instead of finding out from a phone call that someone sent us an important email or something.
The AT&T representative also said that both AT&T and Apple are aware of and are working on the issue as it is a nationwide problem with iPhone 5 and LTE. The Apple Support Advisors I talked to made no mention of this "known" issue. AT&T said that it is partly AT&T responsibility because the capacity of LTE is overloaded and cellular data connections are dropping because of the lack of coverage and/or capacity. They actually refunded my data service for a whole month in apology for the inconvenience (I did not even ask for that--I just want my data service to work). But they also said that Apple has responsibility in this issue because the iPhone 5 should drop down and re-connect to the next lower tier of data service when LTE is not available or lost; instead, it is locking up somehow or it still thinks it is connected to LTE when it is actually not. I don't know how accurate these statements are, but my problem is real.
TEMPORARY WORK-AROUND / FIX FROM AT&T: Disable LTE on the iPhone 5. Or when you figure out that data is not coming to your iPhone, use Airplane Mode ON/OFF for a few seconds to force re-connection to a tower without rebooting the iPhone. You can Disable LTE on the iPhone 5 in SETTINGS/GENERAL/CELLULAR. I have disabled LTE on my iPhone 5 and have not had any of these cellular data issues since.
Disabling LTE is not acceptable either, but it is working. At least I seem not be losing connection or locking up without knowing it. In my office over the course of a day, my iPhone 5 will jump back and forth on LTE and 4G sitting in the same place. Disabling LTE has stopped this and the problem, but the iPhone 5 should switch cellular data services seemlessly just like the phone switches towers on a phone voice call seemlessly (most of the time).
WI-FI ALSO STOPS WORKING SOMETIMES AFTER THIS LTE disconnect / lock-up issue: That has been my experience along with my clients and family as well. If you use Wi-Fi a lot on your iPhone it will hide this LTE issue until you leave your Wi-Fi and get on LTE and then drop LTE (silently) and then go back to your Wi-Fi. My experience has been I have to reboot the iPhone to even get Wi-Fi working again after that happens.
I do not know if some of these comments and analysis are really accurate or valid or not... all I know for sure is since I upgraded my iPhone to the 5 along with my other family members and clients, we have had "no data" on many occasions and are continually rebooting our iPhones and looking for what is wrong.
My questions to the support community are these:
     1. Is anyone else having this issue? Or is it just me and my few? Maybe a lot of people do not realize they are not getting their data because they are on Wi-Fi most of the time or they are just rebooting and not trying to identify the real problem. AT&T said it was nationwide iPhone 5/LTE issue. Anyone else heard that from either Apple or AT&T?
     2. Is this an iPhone 5 / Apple issue or is AT&T solely responsible? Or is it both? Where do we get a solution??? Is AT&T LTE holding false connections with iPhone 5 or is the iPhone 5 failing to recognize a dropped LTE cellular data connection and then failing to attempt to re-connect with 4G or 3G?
     3. Did I miss where this issue is posted? I searched Apple Support and Communities and did not get any hits. Any updates or further insight on the issue? Any other fixes other than Disabling LTE?
      4. If this is in fact a real issue belonging in part to the iPhone 5, we need to escalate Apple’s attention to it.
Thanks in advance for your help and feedback.

Thank you fellow users and experts for your feedback and updates. Sorry about the large font on the original post... accidental via cut and paste.
I have escalated the issue with both Apple and AT&T. I actually got senior level troubleshooters from both Apple and AT&T on the phone at the same time... rare moment. Here are the key points of the update:
     1. AT&T did NOT confirm the earlier statement by another AT&T Technical Support Agent that this was an emerging nationwide issue about iPhone 5 and LTE losing data connection and not reconnecting at a lower level or re-connecting to LTE once the signal came back. So that earlier statement was not accurate as suspected by all of us. The senior tech at AT&T said he has seen this issue sporadically over the last month or so, but only with about 3-4 customers. He said it seems to be location or phone dependent (some phones not all phones).
     2. The Apple Tech was satisfied that all that could be done to eliminate my issues possibly relating to my instance of software / iOS had been accomplished except erasing my iPhone and restoring as a new phone (I have avoided this inconvenience with the argument that other family/clients with the iPhone 5 have had the same problem).
     3. AT&T went so far as to examine which towers I had been connecting to over the last week and looked at other technical data that could possibly explain the issue. I now know I have 3 towers that provide LTE within 4 miles of my home/office, one within a half mile. But so far there is nothing to explain or even properly identify the issue. AT&T offered me to take my phone to an AT&T store, try to force replicate the problem there, if so, the store would put my SIM card in a brand new iPhone 5 (just to test) and try tor replicate the problem again. If replicated on a new phone, there is a deeper issue; if resolved on a new phone, the answer is obvious. I have not taken the time to do this yet.
     4. On Friday, Jan 4, 2013 while talking and between the tech support calls (on a different phone), I was able to re-create the problem 2 separate times in my home/office by forcing my iPhone to weaken its connection to service (burying it under electronic gear) and then waiting a few minutes, then trying to browse the Internet--no data service unless I manually reset the connection. I am only able to cause the issue to occur if there is at least 15 min of idle time after a weak signal condition AND only if I don’t completely lose a connection to cellular voice service. It seems that if you go down to NO SERVICE the phone will do new a search and keep searching until reconnects to LTE or other signals correctly, but a weak connection seems to be strong enough for voice service but can sometimes cause the LTE data service to stop without reconnecting to LTE, 4G or 3G unless I manually intervene. It also seems that idle time with a weak connection is also necessary to re-create the problem manually. Since Friday, I have not been able to re-create the problem. This has been an intermittent problem, so who knows.
FYI, I have never had this problem with my new iPad (also on AT&T LTE) that has been with me when the iPhone fails to have data service, but my iPad is never in my pocket or other places with perhaps less signal.
Again, if you are connected to Wi-Fi on your iPhone 5 most of the time, you may never notice this issue if you are even having it.
So far no progress on the real issue or resolution, but both Apple and AT&T have put forth very admirable effort.
If you or others you know are having this issue, please take the time to post a reply to this issue. Thank you.

Unable to connect SQL Developer 4.0.2 to Oracle REST Data Services 2.0.7 (Apex Listener)

Background
1. Weblogic 10.3.6.0 running on Oracle Linux 6.5 with Oracle JRockit(R) (build R28.2.3-13-149708-1.6.0_31-20120327-1523-linux-x86_64, compiled mode)
2. Oracle Apex 4.2.1
3. Apex Listener 1.1.3
4. Apex and Apex Listener running on the Weblogic box above
5. SQL Developer 4.0.2 running on Windows 7 64 bit / Java 1.7.0_55
Updated Apex to 4.2.5 via p17966818_425_Generic.zip patchset. Apex environment running fine as do all applications via Listener 1.1.3
Updated Oracle Listener to the latest version of Oracle REST Data Services 2.0.7
Current Status
Apex Applications and RESTful services are running fine.
Problem
Unable to connect SQL Developer 4.0.2 to Oracle REST Data Services 2.0.7
Error message in SQL Developer - Cannot connect to DEV. HTTP/1.1 403 Target service not allowed
Additional Information
Steps followed -
1. The oracle users APEX_LISTENER and APEX_REST_PUBLIC_USER did not exist, so I ran apex_rest_config.sql from the APEX 2.4.1 patchset whilst connected sys as sysdba and provided the same password as APEX_PUBLIC_USER for both users.
2. I also ran
grant insert, delete on APEX_040200.wwv_flow_rt$privilege_groups to APEX_LISTENER;
alter session set current_schema = APEX_LISTENER;
create or replace synonym wwv_flow_rt$privilege_groups for APEX_040200.wwv_flow_rt$privilege_groups;
as per Oracle SQL Developer User's Guide Release 4.0
3. copied ords.war to apex.war
4. java -jar apex.war configdir /u01/app/oracle/admin/apex/devdomain1/
5. java -jar apex.war
Jun 5, 2014 5:15:31 PM oracle.dbtools.common.config.file.ConfigurationFolder logConfigFolder
INFO: Using configuration folder: /u01/app/oracle/admin/apex/devdomain1/apex
Enter the name of the database server [localhost]:dbservername
Enter the database listen port [1521]:
Enter 1 to specify the database service name, or 2 to specify the database SID [1]:1
Enter the database service name:dbservicename
Enter the database user name [APEX_PUBLIC_USER]:
Enter the database password for APEX_PUBLIC_USER:
Confirm password:
Enter 1 to enter passwords for the RESTful Services database users (APEX_LISTENER,APEX_REST_PUBLIC_USER), 2 to use the same password as used for APEX_PUBLIC_USER or, 3 to skip this step [1]:2
Jun 5, 2014 5:16:52 PM oracle.dbtools.common.config.file.ConfigurationFiles update
INFO: Updated configurations: defaults, apex, apex_al, apex_rt
Enter 1 if you wish to start in standalone mode or 2 to exit [1]:2
6. java -jar apex.war user adminlistener "Listener Administrator"
Jun 5, 2014 5:18:52 PM oracle.dbtools.common.config.file.ConfigurationFolder logConfigFolder
INFO: Using configuration folder: /u01/app/oracle/admin/apex/devdomain1/apex
Enter a password for user adminlistener:
Confirm password for user adminlistener:
Jun 6, 2014 5:19:12 PM AM oracle.dbtools.standalone.ModifyUser execute
INFO: Created user: adminlistener in file: /u01/app/oracle/admin/apex/devdomain1/apex/credentials
7. Updated the defaults.xml file
Added
<entry key="apex.security.user.roles">RESTful Services</entry>
<entry key="apex.security.developer.roles">OAuth2 Client Developer, SQL Developer</entry>
as per Oracle SQL Developer User's Guide Release 4.0
Changed
<entry key="debug.printDebugToScreen">false</entry>
to
<entry key="debug.printDebugToScreen">true</entry>
for RESTful debugging
Added
<entry key="security.verifySSL">false</entry>
to use OAuth2 in Non HTTPS Environment as per Oracle® REST Data Services Installation and Configuration Guide, Release 2.0
8. Deleted the Admin and Manager Roles within the apex application deployment which were part of the Apex Listener 1.1.3 install
9. Deployed the apex.war in weblogic
10. Stopped and started the weblogic server to which apex.war was deployed
11. In SQL Developer, View, RESTful Services. In the RESTful services windows hit connect, Create a new connection,
Connection Name DEV
Username adminlistener
selected http protocol
Hostname weblogicservername
Port 7250
Server Path /apex
Workspace (blank)
On the Authentication dialog
Username adminlistener
Password passwordsuppliedabove in step 6
Response is a dialog box titled Authentication Failed
message - Cannot connect to DEV. HTTP/1.1 403 Target service not allowed
NOTHING UNUSUAL IN ANY OF THE WEBLOGIC LOG FILES, EXCEPT THAT IT STATES
'Oracle REST Data Services version : 2.0.6.27.18.06' when I've installed 2.0.7.
Any help much appreciated

Further to the above post, I thought I'd simplify my Apex Listener install just to see if I can connect to it via SQL Developer
So downloaded the latest version 2.0.8 and decided to configure and run the Listener on my pc whilst still connecting to the same database.
Operating system : Window 7 Pro 64 bit
Oracle Apex Listener 2.0.8
Java(TM) SE Runtime Environment (build 1.7.0_25-b17)
Java HotSpot(TM) 64-Bit Server VM (build 23.25-b01, mixed mode)
Went through the configuration as above, once started I tried again to access the listener via SQL Developer. This time I received this output from the listener:
INFO: Error: ORA-02291: integrity constraint (APEX_040200.WWV_FLOW_RT$APPROVALS_SGID_FK) violated - parent key not found, occurred during execution of: [CALL, insert into wwv_flow_rt$approvals (user_name,status,client_id,security_group_id,created_by,created_on,updated_by,updated_on) values(/*in:user_id*/?,/*in:status*/?,/*in:client_id*/?,/*in:tenant_id*/?,upper(/*in:user_id*/?),/*in:created*/?,upper(/*in:user_id*/?),/*in:created*/?), [tenant_id, in, class java.math.BigInteger], [client_id, in, class java.math.BigInteger], [user_id, in, class java.lang.String], [status, in, class oracle.dbtools.rt.oauth.ApprovalRequest$Status], [created, in, class java.sql.Timestamp]]with values: [adminlistener, APPROVED, 3858401374580004, -1, adminlistener, 2014-06-23 12:19:18.785, adminlistener, 2014-06-23 12:19:18.785]
SQL Developer responded with an Authentication Failed titled dialog with the following displayed in the body of the dialog
Cannot connect to DEV.
<!DOCTYPE html>





<html>

<html lang="en">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=utf-8">
<meta http-equiv="X-UA-Compatible" content="IE=edge,chrome=1">
<style type="text/css" media="screen">html,body,div,span,h3,p,ol,ul,li,header,hgroup{margin:0;padding:0;border:0;font-size:100%;font:inherit;vertical-align:baseline}header,hgroup{display:block}body{font:normal 12px/16px Arial,sans-serif;margin:0 auto;background:#6a9cda}header#xHeader{border-bottom:1px solid #8fa4c0;position:relative;z-index:10;background:none #000}header#xHeader hgroup{width:974px;margin:0 auto;position:relative;height:36px;background:none #000}header#xHeader a#uLogo{margin:8px 0;display:inline-block;font:bold 14px/20px Arial,sans-serif;color:#AAA;text-decoration:none}header#xHeader a#uLogo span.logo{color:#F00}.no-css3 div#xContentContainer div.xContent{padding-top:14px}.no-css3 div#xContentContainer div.xContent div.xMainLeft h2{margin-top:0}div#xWhiteContentContainer{margin-bottom:30px}div#xWhiteContentContainer.xContentWide{background:#FFF;margin-bottom:0}div#xWhiteContentContainer.xContentWide div.xWhiteContent{-moz-border-radius:0;-webkit-border-radius:0;border-radius:0;-moz-box-shadow:none;-webkit-box-shadow:none;box-shadow:none}div#xWhiteContentContainer div.xWhiteContent{width:974px;margin:0 auto;padding:0 0 20px 0;background:#FFF;min-height:500px;-moz-border-radius:0 4px 4px 4px;-webkit-border-radius:0 4px 4px 4px;border-radius:0 4px 4px 4px;-moz-box-shadow:0 1px 2px rgba(0,0,0,0.15);-webkit-box-shadow:0 1px 2px rgba(0,0,0,0.15);box-shadow:0 1px 2px rgba(0,0,0,0.15)}div#xContentHeaderContainer{background:#6a9cda;-moz-box-shadow:0 -1px 0 rgba(0,0,0,0.15) inset;-webkit-box-shadow:0 -1px 0 rgba(0,0,0,0.15) inset;box-shadow:0 -1px 0 rgba(0,0,0,0.15) inset}div#xContentHeaderContainer div.xContentHeader{width:974px;margin:0 auto;padding:30px 0 32px 0;position:relative;min-height:60px}div#xContentHeaderContainer div.xContentHeader h3{font:bold 24px/24px Arial,sans-serif;color:#fff;text-shadow:0 2px 1px rgba(0,0,0,0.25);margin:0 0 20px 0}div#xFooterContainer{min-height:200px;border-top:1px solid rgba(0,0,0,0.15);background:#6a9cda}body.errorPage div#xContentHeaderContainer div.xContentHeader{min-height:30px}body.errorPage div#xContentHeaderContainer div.xContentHeader h3{font:bold 30px/30px Arial,sans-serif;color:#FFF;text-shadow:0 1px 2px rgba(0,0,0,0.25);margin:0}div.errorPage p{font:normal 14px/20px Arial,sans-seri;color:#666;padding:0 0 10px 0}div.errorPage ul{list-style:disc outside;padding:0 10px 0;margin:0 0 20px 0}div.errorPage ul li{font:normal 12px/16px Arial,sans-serif;color:#666;margin:0 0 8px 10px}pre{font-family:Consolas,"Lucida Console","Courier New",Courier,monospace}
</style>
<script type="text/javascript" charset="utf-8">
'header hgroup'.replace(/\w+/g,
function(n) {
document.createElement(n)
</script>
<title>Internal Server Error</title>
</head>
<body class="errorPage">
<header id="xHeader">
<hgroup>
<a id="uLogo" href="./"><span class="logo">ORACLE</span>
REST DATA SERVICES</a>
</hgroup>
</header>
<div id="xContentHeaderContainer">
<div class="xContentHeader">
<h3>
<span class="statusCode">500</span> - <span
class="statusMessage">Internal Server Error</span>
</h3>
</div>
</div>
<div id="xWhiteContentContainer" class="xContentWide">
<div class="xWhiteContent">
<div class="errorPage">
<p>
<ul class="reasons">
</ul>
</p>
<p>
<pre>Request Path passes syntax validation
Mapping request to database pool: PoolMap [_failed=false, _lastUpdate=-1, _pattern=null, _poolName=apex, _regex=null, _type=REGEX, _workspaceIdentifier=null, _serviceName=null]
Applied database connection info
Attempting to process with PL/SQL Gateway
Not processed as PL/SQL Gateway request
Attempting to process as a RESTful Service
Choosing: oracle.dbtools.rt.oauth.TokenHandler as current candidate with score: Score [handle=null, score=0, scope=SecurityConfig [constraint=secure, realm=OAUTH_CLIENT, logonConfig=NONE], originsAllowed=[], corsEnabled=true]
Determining if request can be dispatched as a Tenanted RESTful Service
Request path has one path segment, continuing processing
No Tenant Principal established yet, continuing processing
APEX_LISTENER pool exists, continuing processing
No matching tenant found for: oauth2, cannot dispatch
Chose oracle.dbtools.rt.oauth.TokenHandler as the final candidate with score: Score [handle=null, score=0, scope=SecurityConfig [constraint=secure, realm=OAUTH_CLIENT, logonConfig=NONE], originsAllowed=[], corsEnabled=true] for: POST oauth2/token
oauth2/token authorized as: p6xycV-2QceFnFHkWyJlnA..
</pre>
</p>
<p>
<pre>WebException [statusCode=500]
at oracle.dbtools.rt.web.WebException.webException(WebException.java:343)
at oracle.dbtools.rt.web.WebException.internalError(WebException.java:262)
at oracle.dbtools.rt.oauth.jdbc.JDBCOAuthDataAccess.createApproval(JDBCOAuthDataAccess.java:514)
at oracle.dbtools.rt.oauth.jdbc.JDBCOAuthDataAccess.createApprovedRequest(JDBCOAuthDataAccess.java:181)
at oracle.dbtools.rt.oauth.OAuthAuthorization.resourceOwnerCredentials(OAuthAuthorization.java:654)
at oracle.dbtools.rt.oauth.OAuthAuthorization.tokenRequest(OAuthAuthorization.java:273)
at oracle.dbtools.rt.oauth.TokenHandler.post(TokenHandler.java:44)
at oracle.dbtools.rt.web.RequestHandler.response(RequestHandler.java:268)
at oracle.dbtools.rt.web.RequestHandler.dispatch(RequestHandler.java:361)
at oracle.dbtools.rt.web.RequestHandler.dispatch(RequestHandler.java:85)
at oracle.dbtools.rt.web.RequestDispatchers.dispatch(RequestDispatchers.java:93)
at oracle.dbtools.rt.web.ETags.checkPrecondition(ETags.java:93)
at oracle.dbtools.rt.web.HttpEndpointBase.restfulServices(HttpEndpointBase.java:426)
at oracle.dbtools.rt.web.HttpEndpointBase.service(HttpEndpointBase.java:164)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:820)
at com.sun.grizzly.http.servlet.ServletAdapter$FilterChainImpl.doFilter(ServletAdapter.java:1059)
at com.sun.grizzly.http.servlet.ServletAdapter$FilterChainImpl.invokeFilterChain(ServletAdapter.java:999)
at com.sun.grizzly.http.servlet.ServletAdapter.doService(ServletAdapter.java:434)
at oracle.dbtools.standalone.SecureServletAdapter.doService(SecureServletAdapter.java:91)
at com.sun.grizzly.http.servlet.ServletAdapter.service(ServletAdapter.java:379)
at com.sun.grizzly.tcp.http11.GrizzlyAdapter.service(GrizzlyAdapter.java:179)
at com.sun.grizzly.tcp.http11.GrizzlyAdapterChain.service(GrizzlyAdapterChain.java:196)
at com.sun.grizzly.tcp.http11.GrizzlyAdapter.service(GrizzlyAdapter.java:179)
at com.sun.grizzly.http.ProcessorTask.invokeAdapter(ProcessorTask.java:849)
at com.sun.grizzly.http.ProcessorTask.doProcess(ProcessorTask.java:746)
at com.sun.grizzly.http.ProcessorTask.process(ProcessorTask.java:1045)
at com.sun.grizzly.http.DefaultProtocolFilter.execute(DefaultProtocolFilter.java:228)
at com.sun.grizzly.DefaultProtocolChain.executeProtocolFilter(DefaultProtocolChain.java:137)
at com.sun.grizzly.DefaultProtocolChain.execute(DefaultProtocolChain.java:104)
at com.sun.grizzly.DefaultProtocolChain.execute(DefaultProtocolChain.java:90)
at com.sun.grizzly.http.HttpProtocolChain.execute(HttpProtocolChain.java:79)
at com.sun.grizzly.ProtocolChainContextTask.doCall(ProtocolChainContextTask.java:54)
at com.sun.grizzly.SelectionKeyContextTask.call(SelectionKeyContextTask.java:59)
at com.sun.grizzly.ContextTask.run(ContextTask.java:71)
at com.sun.grizzly.util.AbstractThreadPool$Worker.doWork(AbstractThreadPool.java:532)
at com.sun.grizzly.util.AbstractThreadPool$Worker.run(AbstractThreadPool.java:513)
at java.lang.Thread.run(Unknown Source)
Caused by: java.sql.SQLIntegrityConstraintViolationException: ORA-02291: integrity constraint (APEX_040200.WWV_FLOW_RT$APPROVALS_SGID_FK) violated - parent key not found
at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:447)
at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:396)
at oracle.jdbc.driver.T4C8Oall.processError(T4C8Oall.java:879)
at oracle.jdbc.driver.T4CTTIfun.receive(T4CTTIfun.java:505)
at oracle.jdbc.driver.T4CTTIfun.doRPC(T4CTTIfun.java:223)
at oracle.jdbc.driver.T4C8Oall.doOALL(T4C8Oall.java:531)
at oracle.jdbc.driver.T4CPreparedStatement.doOall8(T4CPreparedStatement.java:208)
at oracle.jdbc.driver.T4CPreparedStatement.executeForRows(T4CPreparedStatement.java:1046)
at oracle.jdbc.driver.OracleStatement.doExecuteWithTimeout(OracleStatement.java:1336)
at oracle.jdbc.driver.OraclePreparedStatement.executeInternal(OraclePreparedStatement.java:3612)
at oracle.jdbc.driver.OraclePreparedStatement.execute(OraclePreparedStatement.java:3713)
at oracle.jdbc.driver.OraclePreparedStatementWrapper.execute(OraclePreparedStatementWrapper.java:1378)
at sun.reflect.GeneratedMethodAccessor28.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source)
at java.lang.reflect.Method.invoke(Unknown Source)
at oracle.ucp.jdbc.proxy.StatementProxyFactory.invoke(StatementProxyFactory.java:230)
at oracle.ucp.jdbc.proxy.PreparedStatementProxyFactory.invoke(PreparedStatementProxyFactory.java:124)
at com.sun.proxy.$Proxy44.execute(Unknown Source)
at oracle.dbtools.common.jdbc.JDBCInsert.execute(JDBCInsert.java:58)
at oracle.dbtools.rt.oauth.jdbc.JDBCOAuthDataAccess.createApproval(JDBCOAuthDataAccess.java:487)
... 34 more
</pre>
</p>
</div>
</div>
</div>
<div id="xFooterContainer">
</div>
</body>
</html>
I am assuming this must be part of the problem I am seeing this the Weblogic deployment in my original post.
Does anyone have any suggestions on how best to tackle this?
Regards,
Derek

Data Recovery software

how to recovery data from damage hard disk then i found on net i got a http://www.stellarinfo.co.in/
which provide data recovery services i talked to them & they reply they have the solution of hard disk recovery, laptop data recovery, server recovery, raid data recovery i want to know that it there any problem to recover data from these company is it reliable

Tenorshare Data Recovery is a powerful
data recovery software. It not only support recovering data with Windows file system (FAT12, FAT16, FAT32, NTFS), but also Mac file system (HFS, HFS+) and Linux file system (EXT2, EXT3). Lost data due to virus attack PC, corrupted partition, drive crash,
system sabotage, etc. can be retrieved easily with it.
http://www.any-data-recovery.com/product/datarecoveryprofessional.htm

Data Recovery Software for the Zen Vision M

Data Recovery Software for the Zen Vision M:
Has anyone had any success recovering lost sound files from a Vision M, with software, physical repair services, or otherwise? Does anyone claim to be able to recover information from these devices?
The data recovery programs I have tried fail to recognize the dri've, since it doesn't show up in list of dri'ves for some reason (Is there a way to make this show up?). Any suggestions/ recommendations would be greatly appreciated as I lost over a year of recordings after an unexpected forced reformatting. How would one even go about finding someone for this job?
Thanks, GW

Haven't really tried the data recovery so I would like to know more about this one too.
http://storeyourpicture.com/images/s...lectronics.jpg

Sun StorageTek Data Services software

Similar Messages

Maybe you are looking for