Sun ultra 80 Elite 3d hardware issue.Won't boot

Good day,
I'm trying to boot a ultra 80 elite 3D.The memory's are the same.It used to work until I added an extra CPU(same Rev.).The machine powers on then after 30 second I get a low beep sound and thats it,nothing appens :(
Is there something im missing?
thanks in advance,
Mart.

Hello Mart,
please review the keyboard plug, these pins bent very easily.
There are occasions when a direct-connect keyboard can help,
e.g. when the system was powered down by power management and there is no key-switch to power-on ...
STOP-A is basically a BREAK (use ALT+B in TeraTerm Pro to generate this signal).
During POST the LEDs of the direct-attached keyboard show the current status of POST.
and there are times when it is best to remove it and go with
the console connection, off the TTYa port.
The early phase of POST is only visible on the console (serial, RSC, LOM, ALOM), because the display adapter (integrated or add-in board) isn't initialized yet.
If a monitor doesn't support the current display mode, the monitor doesn't sync and the ability to change the mode via serial console is very valuable.
Sometimes reverting to the default OBP settings is required. Either use STOP-N with a direct attached keyboard or BREAK via console and then
set-defaults
setenv auto-boot? false
reset-all
As mentioned before, not properly seated memory modules can cause this hang.
Michael

Similar Messages

MacBookpro Early 2011 graphic issue won't boot

Hello,
My Early 2011 MacBookPro suddenly suffered from graphics issues for a few days then it won't boot at all.
The hardware test says it is ok and my hard drive too. But when I want to boot, the apple appears and the dong too, but then blank screen. It is the same with a bootcamp boot, but with a blue screen with lines all over the screen. The recovery partition doesn't start either. But I can access boot from my hard drive with another Mac on target mode.
Anyway Apple doesn't admit there's a problem a want me to pay the reparation, because they don't report it as a real problem, saying that I damaged the computer. But there are threads here and all over the internet, and they don't want to do anything.
On the phone, the apple guy told me that I had to pay 80$ to see if there is any problem , and " maybe if we see there's a fabrication problem, we'll fix it for free ". Do I have to trust them ? What can I do to ?
Thank you

This thread may be helpful -> https://discussions.apple.com/thread/4766577?tstart=0.
You should at least add your experience and see if those who have come up with 'quick fixes' can help you with your problem.
Good luck,
Clinton

Dual 2.5 cooling issue: Won't boot.

I have a dual 2.5 G5 that I've had since it was new in in july 2004. It's never given me any problems.
Recently it started "gurgling" (it's the best way to describe it). I was worried about the dreaded leaking issue so I tore it apart looking for leaks.
Good news: No leaks. Bad news, it won't boot now.
In the process of assessing the situation I checked the coolant level. To my surprise the system was pressurized quite a bit, even though it was stone cold. I don't understand this. I also get the red LED's on the mother board glowing indicating overheat, the cooling fans run at high velocity, and the computer won't boot.
I am in the process of rebuilding the water pump as a preventative measure, resealing the two O-rings and the diaphragm. Everything seems in working order.
I hope it will boot once I reassemble it, but I'm in a situation where I MUST have it up and running by monday.
Any suggestions?

Hi tarmaque-
It may not be so much about pressure as air in the system. You said yourself that it was pressurized when you disassembled it. That is a huge clue! That fact alone would certainly make me think that there should be pressure.
I think the higher boiling point under pressure is a factor. There isn't much fluid and it must dissipate a lot of heat.
Water cooled engines absolutely are "pressurized"-ever take a radiator cap off of a hot engine? A cooling system must be able to handle pressure as (duh Daddy) liquids expand when hot.
Luck-
-DP

K7N420 Pro -- RAM issues -- won't boot/crashes

System info:
CPU: AMD Athlon XP 1900+
Motherboard Model: K7N420 Pro
Memory: (Varying, this is the problem, explained in post: but to begin with the system had 2 modules of 256MB PC2100 266mHz. Brand name unknown, some generic manufacturer. For reference's sake, the motherboard has THREE memory slots)
Video card: NVIDIA GeForce2 Integrated GPU, GeForce2 Integrated GPU, 32MB
Hard Drive: Western Digital 80GB
Other cards: None that I know of
Operating System: Windows XP Professional Version 2002 Service Pack 2
Power Source: Addtronics 300w (3.3v/18a, 5v/30a, 12v/9a)
Okay, so obviously we've got an old, old beast here.... But she's served me well, and I'd like to get a little more out of her. So here's the ongoing (very long, I'm sorry) saga:
The computer started doing crashing on me some time ago; lots of Blue Screens of Death, no error messages that gave me anything reliable to use for diagnostic purposes. Eventually it just wouldn't even manage to boot, each time would give me a BSOD. I opened the case up, checked for anything obviously visually wrong (blown capacitors etc), did a good thorough aircan dusting, popped out the two 256MB chips (let us call them Chip and Dale), and popped them back in.
This did indeed have a result- now we didn't even make it to the BSOD! All I got was a repeated ominous beeping and nothing coming onto the monitor at all. I then tried to put in only one chip at a time. Results: Chip works in slots #1 and #2, but not #3; Dale works not at all. (By "works" I mean the computer boots normally and runs normally, for at least an hour, the most I've tested it. Runs SLOW, of course, at 256MB, but runs. By "not works" I mean we get nothing on-screen, and the repeated ominous beeping.)
I presumed I had bad memory on my hands with Dale and that I needed new memory anyways, so I headed to Fry's and picked up two sticks of Patriot 512MB PC2100 DDR 266mHz-- the same specs as the old memory, excepting that it is 512MB instead of the 256. (According to Crucial.com, my motherboard's slots should each be able to support 512MB.) Let's call the Patriot 512 chips Bill and Ted.
Results with the new memory: Neither will work in slot #3. Logic dictates slot #3 is bad. Bill will work in slot #1 or slot #2. Ted will work only in slot #1. The computer will NOT boot if both Bill and Ted are occupying slots. (It also won't boot if Chip is occupying a slot and either Bill or Ted are in another slot.)
(Doesn't this sound like like one of those old logic problems where you have to sort out who owns which house?)
So the best I can get out of her right now is to stick Bill or Ted into slot #1 and proceed with the same 512MB that Chip and Dale used to give me back when they cooperated. However, new wrinkle: neither Bill nor Ted will get along with the computer for anything more than about a half-hour-- then, the computer crashes, tries to auto-reboot, and starts doing Black Screen and Ominous Beeping again. The RAM has to be popped out and put back in before it will boot normally.
*deep breath* I know that was long, thanks to anybody who read this far. Does anyone have any ideas as to what could be causing these problems and/or how to fix it? I've reached the end of all the knowledge I can put to work on this problem.
If I haven't been clear on anything, please let me know, I'll try to answer.

Hello,
Are you 100% sure that slot 3 is clean/dust free?
Memtest is a program that writes patterns to the memory.
The program then tries to recall the pattern(data) stored in the memory location.
If the memory is faulty the pattern(data) may have altered (goes corrupt) and the program will report an error.
Use just 1 stick at a time in slot 1.
Patriot Bill, let memtest run for say 3 hours.
If everything is ok you will not see any errors on the screen.
Then turn off and remove patriot Bill.
Insert patriot Ted into slot 1.
Run memtest again for 3 hours.
Again if everything is ok after the 3 hours it means that both Bill and Ted are ok.

Hardware Issue - Won't Accept CD's

Last night I was using my CD on the Mac Mini, and after exjecting the CD it made a few NEW noises. Now I attempt to put a CD back in, it seems to have something on the right blocking the CD from being inserted.
I have no problem opening this machine (yes, I know how), but I'd like to know if anyone else experienced the same problem AND fixed it. I figure the CD drive got jammed in the eject mode, and hasn't reset.
Suggestions? (BTW: I've already tried the re-boot holding the eject button down twice - no dice)
Mac Mini (PowerPC G4) 1.25ghz Mac OS X (10.4.6)

OK, it works fine for now.
After getting the proper sized screwdriver from Home Depot, I was able to open the cover to the Super Drive directly (4 screws).
The one actually blocking the CD from entering was lock (if I forced it, it would have broken), but towards the back of the dive another arm was engaged, so I gently pushed it back on the same plan as a CD would -- it was a little stiff but it worked. That move then disengaged the other portion blocking the CD from entering. Then, I reinstalled in back into the Mac - make sure the Mac is off (yes, I left the drive cover off).
After booting up the mac, the drive when through it check cycle (the parts actually raised above the plan). Once that worked, I inserted the CD. It worked fine without having the drive cover on top - I could see the full CD spins like normal. I tested it and made sure I could access informational, and it all worked fine.
That's it folks. I save money (for now $110) and have my mini up and running again.
Since it really had no reason to break in the first place, it's likely that the error might happen again, but until then - I have a working drive.
(Sorry, next time I'll take photos)
Mac Mini (older) Mac OS X (10.4.6)

Passed hardware test, won't boot

I am trying to get my 2008 iMac running again. I replaced the hard drive after it quit working. I have the boot cd in and when I ran the hardware test there were
No issues. All that I get is the missing file (flashing question mark) screen. I can't get it in verbose, or boot it from the cd. I've been using mac since the early 80's and have never had to have one professionally fixed. Any ideas?

I know... I can't figure out why it won't. I've even tried multiple keyboards to be sure... It stays on the gray screen longer than usual, and goes to the missing file icon.

MacBook Pro HD issues; won't boot to any drive; need to recover data

*Apologies in advance for the lengthy post. I just want to be sure I include as much detail as possible. Thanks in advance for reading all of this and offering any thoughts and suggestions.
I have a 13-inch late 2011 MacBook Pro running OS 10.7.
The computer recently began booting slower and slower until finally one day it did nothing but show the gray boot screen with the apple and a spinning circle and/or progress bar at the bottom. It won't do anything else. I assume it's the HD; no surprise there. What's killing me is that no matter what I do, I can't boot to any disk, internal or external, can't mount it in target disk mode, and can't repair it or recover data, which is a first for me with any HD. However, the computer still clearly sees the drive, and the drive sounds and runs normally (meaning no clicks; appropriate amount of whirs and such).
What I've done so far:
Reset PRAM — no help
Reset SMC — no help
Boot in Safe Mode — same result as regular boot: gray logo screen with spinning wheel
Disk Utility message:
Verify Disk — "Error: This disk nees to be repaired. Click Repair Disk."
Repair Disk — gets as far as "Checking catalog file" then shows "Keys out of order". Next is "Rebuilding catalog B-tree." Then "The volume Macintosh HD could not be repaired."
fsck — same as Disk Utility: "Keys out of order (4, 22016)", "Rebuilding catalog B-tree", then "The volume Macintosh HD could not be repaired." FILE SYSTEM WAS MODIFIED." ...over and over again
If I hold Option while starting the computer, it gives me only two drives to boot from, regardless of any other external HDs or flash drives I have attached: Macintosh HD (internal), and Recovery HD (internal partition). If I choose Macintosh HD, it's hit or miss whether it prompts the Disk Utility screen or just gray-screens forever. If I choose Recovery HD, it successfully runs Disk Utility every time. Here's the thing, though — if I attach an external HD, it doesn't see it during the initial Option-startup. However, from Disk Utility I'm able to select a startup disk from the menu to restart into. It sees the externals in there every time and lets me select them as startup disks, but upon restart it returns to the gray Apple logo screen with spinning wheel and/or progress bar at bottom. Sometimes it also sees the internal Macintosh HD here, but selecting that is useless. I can't actually boot from any disk, internal or external, running full OS or even just recovery software.
I've tried using TechTool Pro 8's edisk and ProToGo bootable drives, but again, the MacBook only sees them from Disk Utility only (not on Option-start), and I can select them, but it doesn't actually boot to them; it reverts back to gray screen.
I've installed a full version of OS 10.10.2 on an external hard drive, complete with DiskWarrior 4 on it, but same problem as above — it sees it in the "Select Startup Disk" menu, but not in the initial Option-start or successful reboot.
I've tried booting from a DiskWarrior 4 DVD using C-startup. It recognizes and spins the DVD from the get-go. Eventually it boots to it (after about 20 minutes or so of reading the DVD). I'm able to launch DiskWarrior 4 and start a rebuild. However, it goes all the way through "Step 6: Constructing optimized replacement directory... Overlapped files detected: 7 ...Step 7: Finishing construction ...Step 8: Reading from disc, one moment please..." and then the computer kernel panicked. This happened several times. I reset the PRAM again, then retried DiskWarrior DVD boot, this avoided a kernel panic and it got as far as "Comparing directories... Step 9: Recording any file or folder differences; 3,449,089,956 tests..." and then DiskWarrior and the computer both freeze and I have to force shutdown.
The drive will not mount to another laptop in Target Disk Mode.
Disk Arbitrator immediately sees the the faulty laptop HD, but won't let me mount or unmount it. It's just there, grayed out.
Data Rescue 4 is able to see the faulty laptop HD through Target Disk Mode, even though the drive itself will not mount to my desktop. I am able to scan the drive using DR4, and start a data recovery process. However, DR4 is dumping all recovered data into "User Defined" ai (Adobe Illustrator) files, which makes absolutely no sense at all. What's more, the files aren't able to be opened by any program. Even files that it hasn't recovered into ai files, like txt and mpegs, cannot be opened. I've tried recovering from both the drive itself and from a clone of the drive (made through DR4), with the same result each time.
So, all of that said, I guess my first question is what the **** is going on? The drive mechanically is functioning fine, but there seems to be an issue with its readability (and the directory/files?).
What's more, why won't this laptop mount ANY drive? I should be able to Option-boot into any drive, especially if the USB ports, drives, and OS's are all fully functional, right? Is there any workaround I'm missing? Even if the internal drive and data are just screwed, what's causing a total lack of mounting or booting of any drive, internal or external?

Holy crap, I got it to work.
Essentially, I just waited until DiskWarrior reached Step 9 and told it to skip the step before it had a chance to freeze. It skipped successfully, moved on, rebuilt and replaced the faulty directory files.
So far the computer is booting like normal, I can log in, and I'm currently copying all of the data to an external as I type this.
I still have no idea why the computer wouldn't mount or boot to any drive, but I guess I'll deal with that later.

Format issues- won't boot from OSX disc

Help!
I've been having some issues with my iBook G4 recently (it seems every program will randomly quit unexpectedly and it's generally rather slow) so I was thinking I would just wipe the drive and start afresh.
But I can't seem to boot from the OSX install disc. There's an option in the disc itself to restart and that didn't do anything and pressing "c" while restarting still starts things up normally. I've tried zapping NVRAM, PRAM, I went through OF and did reset-all and set-defaults (I'm not even sure if that was necessary- I'm desperate!) and nothing will work.
Help, please!

In order to erase your internal hard drive, you have to be booted from something else. I think you could do this from another Mac in FireWire Target Disk Mode, but I have never done this myself.
http://support.apple.com/kb/HT1661
Is there a reason you don't want to use FireWire?
The biggest problem still seems to be that either your disc or your optical drive is not working properly. Even if you do succeed in erasing the drive, there is still the problem of reinstalling the OS. I think there are methods of doing this with FireWire Target Disk Mode, but I have just never done it myself, so I hesitate to give any instructions.
If you can, you might see if you can borrow an external optical drive and see if you can boot using that. If so, you can erase and reformat your internal drive using Disk Utility and reinstall the OS that way. If an external optical drive won't work, there may be a problem with your disc.
Good luck!

CD/DVD-rom Issues; Won't Boot

   Hi, I am having a problem booting when I remove my CD-Rom 'Slave' or try to replace it with a DVD-Rom.
Below I will give my computer specs.
I have 2 hard drives, so the Primary IDE slots hold my 2 hard drives; one a
Master and the second one is the slave to the master.
On the Seconday IDE slots, I also have 2 cd-roms, one is the master and the
other is the slave to the master. The master is my cd/read/write cd-rom. I
want to leave it and change the slave cd-rom to a DVD-rom (not a dvd r/w
rom)...
I bought bestbuys dvd-rom, took out the 'slave' cd-rom and put the dvd-rom
in with the pin set for the slave. I booted my computer and it wouldn't boot
pass the first booting page. It wouldn't boot into windows.. What could be
wrong?????????
I took the new dvd-rom back out and left the secondary slave empty and tried booting and it
wouldn' t boot with nothing in the secondary cd-rom bay .. wierd to say the
least.. Like I said the secondary IDE slot is the Master of r/w cd-rom and I
never removed it or touched it, it is still there..
I then put my old cd-rom back in the secondary (slave) and waited a few
mintues and booted up my computer.. It booted with no problem.. I repeated
this whole sequence several times with the same results.. I for the life of
can't figure it out... My computer should boot with or without the second
cd-rom (slave), shouldn't it????? Adding a cd-rom or a dvd-rom should not keep my
computer from booting up should it?????
In my cmos, I have it set to boot-up with the hard drive as my first
boot-up, the second is the cd-rom.. but I don't see how removing or replacing
the 'slave' cd-rom would prevent it from booting into windows..
Yes, I have check the cables, settings and everything in my whole computer.
Can someone please tell me what is causing this.. I need a dvd-rom drive.
not paticularly the brand of the dvd-rom I just bought (which I have already
took back anyway) but I do need to get a dvd-rom asap in my computer so I am
hoping someone might know a solution to this problem..
Thanx for any help,
Granny (below are my specs)
SYSTEM INFORMATION:
Mother Board: K7N2 Delta series MS-6570 (v1.X) ATX Mainboard
AMD Athlon™ XP 2500+ 1.84 GHz, 2.00 GB Ram
OS Name   Microsoft Windows XP Home Edition
Version   5.1.2600 Service Pack 2 Build 2600
OS Manufacturer   Microsoft Corporation
System Manufacturer   NVIDIA
System Model   AWRDACPI
System Type   X86-based PC
Processor   x86 Family 6 Model 10 Stepping 0 Authentic AMD ~1837 MHz
BIOS Version/Date   Phoenix Technologies, LTD 6.00 PG, 11/7/2003
SMBIOS Version   2.3
NVIDIA GeForce 6800 GT Video card 256MB
System Directory   C:\WINDOWS\system32
Boot Device   \Device\HarddiskVolume1
Hardware Abstraction Layer   Version = "5.1.2600.2180 (xpsp_sp2_rtm.040803-2158)"
Total Physical Memory   2,048.00 MB (just updated my ram from 512 mb last week)
Available Physical Memory   1.59 GB
Total Virtual Memory   2.00 GB
Available Virtual Memory   1.95 GB
Page File Space   2.60 GB
Page File   C:\pagefile.sys
Power Supply 400 Antex (ATX12V)
Primary IDE
Master 40 GB Hard Drive
Slave 160 GB Hard Drive
Secondary IDE
Master CD-R/W Rom: TDK 52x EIDE
Slave to Master CD-R/W Rom: MTRP 50x EIDE
This is all it gave on the storage/ide under my system info;
Storage/IDE
Name   Standard Dual Channel PCI IDE Controller
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID PCI\VEN_10DE&DEV_0065&SUBSYS_57001462&REV_A2\3&13C0B0C5&0&48
I/O Port   0x0000F000-0x0000F00F
Driver   c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes),
Name   Primary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&26D47942&0&0
I/O Port   0x000001F0-0x000001F7
I/O Port   0x000003F6-0x000003F6
IRQ Channel   IRQ 14
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes),
Name   Secondary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&26D47942&0&1
I/O Port   0x00000170-0x00000177
I/O Port   0x00000376-0x00000376
IRQ Channel   IRQ 15
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes),

With the one drive alone did you remove the jumper?
Sometimes drives are picky and fight over who is master/slave. Try switching them.

Sun Ultra 20 M2 fails to boot if an USB storage device is plugged in

Hi.
If any of my LaCie external USB disks are plugged in my Sun Ultra 20 M2, BIOS hangs and fails to boot. Bios is upgraded with latest version (Tools and drivers CD v. 1.6a). Furthermore, my LaCie mobile disk is listed on Solaris HCL.
LaCie Lacie Mobile Hard Drive 250 GB
Any hint on how to troubleshoot this issue?
Thanks,
Enrico.

I indeed each a test with every USB device I could collect, including keyboards, and I did have the same problems with others disks, although no one with other kind of hardware.
Not being a problem of my disk, is it possible to file a bug for a workstation BIOS?
Thanks,
Enrico,

IMac won't boot anymore after power cut

Thanks to the great storms in New Jersey, my iMac does not boot anymore after a power cut. Does not get past the apple logo screen with the spinning wheel and keeps rebooting every 2 minutes.
I was able to mount the HD via Firewire on a host machine and the disk seemed fine.
I booted from the Install disk and ran Disk Utility - seemed fine though I could not verify the disk permissions ?
One other thing - I seemed to remember the white light (front bottom right) was blinking before during start-up. Now it goes and stays black after couple of seconds.
Help please,
Philippe

HI Phillipe and Welcome to Apple Discussions...
If you haven't done so, try running the Apple Hardware Test.
http://support.apple.com/kb/HT1509
I doubt repairing disk permissions can't help this problem. It sounds like a hardware issue.
*"I booted from the Install disk and ran Disk Utility - seemed fine though I could not verify the disk permissions ?"*
When you ran Disk Utility via Firewire, did you actually Verify the hard disk for errors?
Carolyn

Memory hardware issue... won't boot

I can't make heads or tails of this one...
I have a dv5z-1000 laptop and up until about 2 weeks ago it was all running okay.
Long story short... I thought the problem was heat and it probably was part of the issue. I have replaced the thermal pad on the cpu with grease and made a shim for the gpu and also added grease to it.
Anyway. The laptop won't boot if I have both sticks of memory in it. I can put each stick of memory in the laptop by themselves and it boots. However, as soon as I put both sticks in the problems starts...
I have had the same memory for over a year with no problems and I don't know what to try next.

Hello Mart,
please review the keyboard plug, these pins bent very easily.
There are occasions when a direct-connect keyboard can help,
e.g. when the system was powered down by power management and there is no key-switch to power-on ...
STOP-A is basically a BREAK (use ALT+B in TeraTerm Pro to generate this signal).
During POST the LEDs of the direct-attached keyboard show the current status of POST.
and there are times when it is best to remove it and go with
the console connection, off the TTYa port.
The early phase of POST is only visible on the console (serial, RSC, LOM, ALOM), because the display adapter (integrated or add-in board) isn't initialized yet.
If a monitor doesn't support the current display mode, the monitor doesn't sync and the ability to change the mode via serial console is very valuable.
Sometimes reverting to the default OBP settings is required. Either use STOP-N with a direct attached keyboard or BREAK via console and then
set-defaults
setenv auto-boot? false
reset-all
As mentioned before, not properly seated memory modules can cause this hang.
Michael

I think there is a hardware issue with my computer and i am not sure what to do it won't let me play netflix

I recently updated my computer and since then it hasn't let me play netflix saying it is a hardware issue. I'm not sure what to do.

Have you tried (re)installing Silverlight?
https://help.netflix.com/en/node/2086
If that doesn't/didn't work, try clearing history and website data (in Safari: check the History menu and scroll all the way down).

Solaris 8 SPARC SUN ULTRA 10 - WP event on CPU0

Hii everyone
My Server SUN 5.8 has rebooted itself after having been generated internally out of the ordinary events related to CPU.
The log en the file.messages and output of prtdiag is:
{color:#ff0000}Apr 15 21:20:10 server1 SUNW,UltraSPARC-IIi: [ID 727863 kern.warning] WARNING: [AFT1] WP event on CPU0, errID 0x000091eb.e4c47547{color}
{color:#ff0000}Apr 15 21:20:10 server1 AFSR 0x00000000.00800040<WP> AFAR 0x000001ff.dbfffdd8{color}
{color:#ff0000}Apr 15 21:20:10 server1 AFSR.PSYND 0x0040(Score 95) AFSR.ETS 0x00 Fault_PC 0x4e3a98{color}
{color:#ff0000}Apr 15 21:20:10 server1 UDBH 0x0000 UDBH.ESYND 0x00 UDBL 0x0000 UDBL.ESYND 0x00{color}
{color:#ff0000}Apr 15 21:20:10 server1 unix: [ID 836849 kern.notice] {color}
{color:#ff0000}Apr 15 21:20:10 server1 ^Mpanic[cpu0]/thread=30001d205a0: {color}
{color:#ff0000}Apr 15 21:20:10 server1 unix: [ID 401469 kern.notice] [AFT1] errID 0x000091eb.e4c47547 WP Error(s){color}
{color:#ff0000}Apr 15 21:20:10 server1 See previous message(s) for details{color}
{color:#ff0000}Apr 15 21:20:10 server1 unix: [ID 100000 kern.notice] {color}
{color:#ff0000}Apr 15 21:20:10 server1 genunix: [ID 723222 kern.notice] 000002a10091d6c0 SUNW,UltraSPARC-IIi:cpu_aflt_log+4e0 (2a10091d77e, 1, 10143958, 2a10091d908, 2a10091d7cb, 10143980){color}
{color:#ff0000}Apr 15 21:20:10 server1 genunix: [ID 179002 kern.notice] %l0-3: 0000000000000001 000002a10091d9e0 0000000000000003 0000000000000010{color}
{color:#ff0000}Apr 15 21:20:10 server1 %l4-7: 0000000000000001 00000000845d5bc0 0000000084407f7c 0000000000000000{color}
{color:#ff0000}Apr 15 21:20:10 server1 genunix: [ID 723222 kern.notice] 000002a10091d910 SUNW,UltraSPARC-IIi:cpu_async_error+7dc (1, 1ffdbfffdd8, 800040, 0, 0, 0){color}
{color:#ff0000}Apr 15 21:20:10 server1 genunix: [ID 179002 kern.notice] %l0-3: 0000000000000000 0640000000800040 0000000000000000 0000000000800040{color}
{color:#ff0000}Apr 15 21:20:10 server1 %l4-7: 000002a10091d9e0 000002a10091dba0 0000000000000000 0000000000000000{color}
{color:#ff0000}Apr 15 21:20:10 server1 unix: [ID 100000 kern.notice]{color}
Apr 15 21:20:10 server1 genunix: [ID 672855 kern.notice] syncing file systems...
Apr 15 21:20:10 server1 genunix: [ID 733762 kern.notice] 6
Apr 15 21:20:11 server1 genunix: [ID 733762 kern.notice] 3
Apr 15 21:20:12 server1 genunix: [ID 904073 kern.notice] done
Apr 15 21:20:13 server1 genunix: [ID 353387 kern.notice] dumping to /dev/dsk/c0t0d0s1, offset 107479040
Apr 15 21:20:24 server1 genunix: [ID 409368 kern.notice] ^M100% done: 13157 pages dumped, compression ratio 3.21,
Apr 15 21:20:24 server1 genunix: [ID 851671 kern.notice] dump succeeded
Apr 15 21:21:08 server1 genunix: [ID 540533 kern.notice] ^MSunOS Release 5.8 Version Generic_108528-09 64-bit
Apr 15 21:21:08 server1 genunix: [ID 913631 kern.notice] Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved.
Apr 15 21:21:08 server1 genunix: [ID 678236 kern.info] Ethernet address = 0:3:ba:c:c6:5e
Apr 15 21:21:08 server1 unix: [ID 389951 kern.info] mem = 1048576K (0x40000000)
Apr 15 21:21:08 server1 unix: [ID 930857 kern.info] avail mem = 1027547136
Apr 15 21:21:08 server1 rootnex: [ID 466748 kern.info] root nexus = Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 440MHz)
Apr 15 21:21:08 server1 rootnex: [ID 349649 kern.info] pcipsy0 at root: UPA 0x1f 0x0
Apr 15 21:21:08 server1 genunix: [ID 936769 kern.info] pcipsy0 is /pci@1f,0
Apr 15 21:21:08 server1 pcipsy: [ID 370704 kern.info] PCI-device: pci@1,1, simba0
Apr 15 21:21:08 server1 genunix: [ID 936769 kern.info] simba0 is /pci@1f,0/pci@1,1
Apr 15 21:21:08 server1 pcipsy: [ID 370704 kern.info] PCI-device: pci@1, simba1
Apr 15 21:21:08 server1 genunix: [ID 936769 kern.info] simba1 is /pci@1f,0/pci@1
Apr 15 21:21:18 server1 simba: [ID 370704 kern.info] PCI-device: ide@3, uata0
Apr 15 21:21:18 server1 genunix: [ID 936769 kern.info] uata0 is /pci@1f,0/pci@1,1/ide@3
Apr 15 21:21:18 server1 uata: [ID 114370 kern.info] dad0 at pci1095,6460
Apr 15 21:21:18 server1 uata: [ID 347839 kern.info] target 0 lun 0
Apr 15 21:21:18 server1 genunix: [ID 936769 kern.info] dad0 is /pci@1f,0/pci@1,1/ide@3/dad@0,0
Apr 15 21:21:19 server1 dada: [ID 365881 kern.info] <ST320414A cyl 39533 alt 2 hd 16 sec 63>
Apr 15 21:21:19 server1 uata: [ID 114370 kern.info] dad1 at pci1095,6460
Apr 15 21:21:19 server1 uata: [ID 347839 kern.info] target 1 lun 0
Apr 15 21:21:19 server1 genunix: [ID 936769 kern.info] dad1 is /pci@1f,0/pci@1,1/ide@3/dad@1,0
Apr 15 21:21:20 server1 dada: [ID 365881 kern.info] <Maxtor 6E040L0 cyl 19156 alt 2 hd 16 sec 255>
Apr 15 21:21:20 server1 swapgeneric: [ID 308332 kern.info] root on /pci@1f,0/pci@1,1/ide@3/disk@0,0:a fstype ufs
Apr 15 21:21:20 server1 simba: [ID 370704 kern.info] PCI-device: ebus@1, ebus0
Apr 15 21:21:20 server1 ebus: [ID 521012 kern.info] power0 at ebus0: offset 14,724000
Apr 15 21:21:20 server1 genunix: [ID 936769 kern.info] power0 is /pci@1f,0/pci@1,1/ebus@1/power@14,724000
Apr 15 21:21:20 server1 ebus: [ID 521012 kern.info] su0 at ebus0: offset 14,3083f8
Apr 15 21:21:20 server1 genunix: [ID 936769 kern.info] su0 is /pci@1f,0/pci@1,1/ebus@1/su@14,3083f8
Apr 15 21:21:20 server1 ebus: [ID 521012 kern.info] su1 at ebus0: offset 14,3062f8
Apr 15 21:21:20 server1 genunix: [ID 936769 kern.info] su1 is /pci@1f,0/pci@1,1/ebus@1/su@14,3062f8
Apr 15 21:21:21 server1 rootnex: [ID 349649 kern.info] ffb0 at root: UPA 0x1e 0x0
Apr 15 21:21:21 server1 genunix: [ID 936769 kern.info] ffb0 is /SUNW,ffb@1e,0
Apr 15 21:21:21 server1 unix: [ID 987524 kern.info] cpu0: SUNW,UltraSPARC-IIi (upaid 0 impl 0x12 ver 0x91 clock 440 MHz)
Apr 15 21:21:21 server1 ebus: [ID 521012 kern.info] se0 at ebus0: offset 14,400000
Apr 15 21:21:21 server1 genunix: [ID 936769 kern.info] se0 is /pci@1f,0/pci@1,1/ebus@1/se@14,400000
Apr 15 21:21:22 server1 hme: [ID 517527 kern.info] SUNW,hme0 : PCI IO 2.0 (Rev Id = c1) Found
Apr 15 21:21:22 server1 simba: [ID 370704 kern.info] PCI-device: network@1,1, hme0
Apr 15 21:21:22 server1 genunix: [ID 936769 kern.info] hme0 is /pci@1f,0/pci@1,1/network@1,1
Apr 15 21:21:25 server1 genunix: [ID 454863 kern.info] dump on /dev/dsk/c0t0d0s1 size 512 MB
Apr 15 21:21:26 server1 hme: [ID 517527 kern.info] SUNW,hme0 : Internal Transceiver Selected.
Apr 15 21:21:26 server1 hme: [ID 517527 kern.info] SUNW,hme0 : Auto-Negotiated 100 Mbps Half-Duplex Link Up
Apr 15 21:22:36 server1 pseudo: [ID 129642 kern.info] pseudo-device: devinfo0
Apr 15 21:22:36 server1 genunix: [ID 936769 kern.info] devinfo0 is /pseudo/devinfo@0
Apr 15 21:23:36 server1 named[184]: [ID 295310 daemon.notice] starting. in.named BIND 8.2.2-P5 Wed Jan 15 04:35:48 PST 2003
Apr 15 21:23:36 server1 Generic Patch-5.8-January 2003
Apr 15 21:23:37 server1 named[221]: [ID 295310 daemon.notice] Ready to answer queries.
Apr 15 21:23:37 server1 named[221]: [ID 295310 daemon.warning] check_hints: A records for L.ROOT-SERVERS.NET class 1 do not match hint records
Apr 15 21:23:38 server1 savecore: [ID 570001 auth.error] reboot after panic: [AFT1] errID 0x000091eb.e4c47547 WP Error(s)
Apr 15 21:23:38 server1 See previous message(s) for details
Apr 15 21:23:57 server1 pseudo: [ID 129642 kern.info] pseudo-device: tod0
Apr 15 21:23:57 server1 genunix: [ID 936769 kern.info] tod0 is /pseudo/tod@0
Apr 15 21:23:57 server1 pseudo: [ID 129642 kern.info] pseudo-device: pm0
Apr 15 21:23:57 server1 genunix: [ID 936769 kern.info] pm0 is /pseudo/pm@0
Apr 15 21:23:59 server1 pseudo: [ID 129642 kern.info] pseudo-device: vol0
Apr 15 21:23:59 server1 genunix: [ID 936769 kern.info] vol0 is /pseudo/vol@0
Apr 15 21:23:59 server1 scsi: [ID 365881 kern.info] /pci@1f,0/pci@1/scsi@1 (glm0):
Apr 15 21:23:59 server1 Rev. 6 Symbios 53c875 found.
Apr 15 21:23:59 server1 scsi: [ID 365881 kern.info] /pci@1f,0/pci@1/scsi@1 (glm0):
Apr 15 21:23:59 server1 glm0 supports power management.
Apr 15 21:23:59 server1 simba: [ID 370704 kern.info] PCI-device: scsi@1, glm0
Apr 15 21:23:59 server1 genunix: [ID 936769 kern.info] glm0 is /pci@1f,0/pci@1/scsi@1
Apr 15 21:23:59 server1 scsi: [ID 193665 kern.info] sd0 at uata0: target 2 lun 0
Apr 15 21:23:59 server1 genunix: [ID 936769 kern.info] sd0 is /pci@1f,0/pci@1,1/ide@3/sd@2,0
Apr 15 21:24:02 server1 pseudo: [ID 129642 kern.info] pseudo-device: fcode0
Apr 15 21:24:02 server1 genunix: [ID 936769 kern.info] fcode0 is /pseudo/fcode@0
Apr 15 21:24:06 server1 ebus: [ID 521012 kern.info] fd0 at ebus0: offset 14,3023f0
Apr 15 21:24:06 server1 genunix: [ID 936769 kern.info] fd0 is /pci@1f,0/pci@1,1/ebus@1/fdthree@14,3023f0
Apr 15 21:24:26 server1 pseudo: [ID 129642 kern.info] pseudo-device: pm0
Apr 15 21:24:26 server1 genunix: [ID 936769 kern.info] pm0 is /pseudo/pm@0
================================= *{color:#0000ff}DATOS DE DIAGNOSTICO{color}* ============================================
server1 ROOT [9] psrinfo -v
Status of processor 0 as of: 04/16/08 09:45:18
Processor has been on-line since 04/15/08 21:21:20.
The sparcv9 processor operates at 440 MHz,
and has a sparcv9 floating point processor.
server1 ROOT [10]
server1 ROOT [9] uname -a
SunOS server1 5.8 Generic_108528-09 sun4u sparc SUNW,Ultra-5_10
server1 ROOT [19] /usr/platform/sun4u/sbin/prtdiag -v
System Configuration: Sun Microsystems sun4u Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 440MHz)
System clock frequency: 110 MHz
Memory size: 1024 Megabytes
========================= CPUs =========================
Run Ecache CPU CPU
Brd CPU Module MHz MB Impl. Mask
0 0 0 440 2.0 12 9.1
========================= IO Cards =========================
Bus# Freq
Brd Type MHz Slot Name Model
0 PCI-1 33 1 ebus
0 PCI-1 33 1 network-SUNW,hme
0 PCI-1 33 2 SUNW,m64B ATY,GT-C
0 PCI-1 33 3 ide-pci1095,646.1095.646.3
0 PCI-2 33 1 scsi-glm Symbios,53C875
Bus Freq
Brd Type MHz Slot Name Model
0 UPA 110 30 FFB, Double Buffered SUNW,501-4788
No failures found in System
===========================
========================= HW Revisions =========================
ASIC Revisions:
Cheerio: ebus Rev 1
FFB Hardware Configuration:
Board rev: 2
FBC version: 0x3241906d
DAC: Brooktree 9070, version 1
3DRAM: Mitsubishi 130b, version 2
System PROM revisions:
OBP 3.29.0 2000/12/20 18:45 POST 3.1.0 2000/06/27 13:56
=== *{color:#0000ff}SECOND TEST{color}*
server1 ROOT [4] /usr/platform/`uname -i`/sbin/prtdiag -v
System Configuration: Sun Microsystems sun4u Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 440MHz)
System clock frequency: 110 MHz
Memory size: 1024 Megabytes
========================= CPUs =========================
Run Ecache CPU CPU
Brd CPU Module MHz MB Impl. Mask
0 0 0 440 2.0 12 9.1
========================= IO Cards =========================
Bus# Freq
Brd Type MHz Slot Name Model
0 PCI-1 33 1 ebus
0 PCI-1 33 1 network-SUNW,hme
0 PCI-1 33 2 SUNW,m64B ATY,GT-C
0 PCI-1 33 3 ide-pci1095,646.1095.646.3
0 PCI-2 33 1 scsi-glm Symbios,53C875
Bus Freq
Brd Type MHz Slot Name Model
0 UPA 110 30 FFB, Double Buffered SUNW,501-4788
No failures found in System
===========================
========================= HW Revisions =========================
ASIC Revisions:
Cheerio: ebus Rev 1
FFB Hardware Configuration:
Board rev: 2
FBC version: 0x3241906d
DAC: Brooktree 9070, version 1
3DRAM: Mitsubishi 130b, version 2
System PROM revisions:
OBP 3.29.0 2000/12/20 18:45 POST 3.1.0 2000/06/27 13:56
============================================
I don't know exactly what is the origin of the problem, How to solver or how to prevent to avoid further problems. This is the first time I have had this Kind of problem on my Server SUN.
I appreciate greatly, any tip o help.
Jimmy

Yup.
EOL in November 2002
Which means EOSL November 2007
http://sunsolve.sun.com/handbook_pub/validateUser.do?target=Systems/U10/U10
Unless you've somehow maintained a service contract on that system,
by specific system serial number,
your best bet is to haunt an online auction site (such as Ebay),
and get a replacement cpu or cpus for shelf stock.
Your current OBP patch level is only down two patch levels,
but your kernel patch level is essentially "never patched".
If it were patched better it may have noticed the issue a lot sooner.
Expect to replace that cpu.

Sun Ultra 10 with SunStorEDGE A1000/D1000 unable to setup

I realise this covers old ground but I have not been able to trace a uitable resolvement and would be grateful for assistance.
I have a Sun Ultra 10 with 256MB RAM and 440GHz cpu.. It has a pci Adaptec 2944UW HVD SCSI interface card. The storage system is a tray of eight scsi 72GB disks housed in a D1000 case. NetBSD reported it as an A1000 SunStorEDGE at sd0 having 16 targets and 8 luns. However NetBSD did not have a readily available controller to setup the raid system so I installed an alternative. I presume the case is a reused old case housing an A1000 unit.
I tried to format the drives directly but they are not lists as devices such as ct1sd1 etc. and so this is not possible.
I have installed Sun Solaris 10 but could not communicate and reported inability to use rdriver and rdnexus and after reading a number of reports that driver hooks had been removed from the kernel in Solaris 10 I have installed Solaris 9.
On both occasions I installed a number of RAID Manager 6.1.1 control packs, namely SUNWosafw, osar, osau, osamn and vtsse direct from my CD here.
I commanded dr_hotadd.sh to take up the challenge but it failed to communicate.
I added a number of Rdac amendments to rparams in /etc/osa but this did not resolve the issue.
I have tried to call probe-scsi-all after doing a reset-all from the OBP but this fails to report anything. I presume this is because the unit is connected by the interface card rather than a direct scsi disk.
dmesg pipe grep scsi reports:
unknown scsi sd0 at uata0 target 2 lun 0
I would be very grateful fr guidance to resolve this connection so that I can create a suitable filestore.
Thanks
c

blackfoot wrote:
I realise this covers old ground but I have not been able to trace a uitable resolvement and would be grateful for assistance.
I have a Sun Ultra 10 with 256MB RAM and 440GHz cpu.. It has a pci Adaptec 2944UW HVD SCSI interface card. The storage system is a tray of eight scsi 72GB disks housed in a D1000 case. NetBSD reported it as an A1000 SunStorEDGE at sd0 having 16 targets and 8 luns. However NetBSD did not have a readily available controller to setup the raid system so I installed an alternative. I presume the case is a reused old case housing an A1000 unit.If it's really an A1000, you won't have access to the drives. You'll only see exposed LUNS from the raid controller. Do you have a dial in the rear with a scsi address? That will be the address that the A1000 will respond on. In addition, the A1000 has only one pair of SCSI ports. The D1000 has two pair and doesn't have the scsi adress dial (because each of the disks in the chassis respond on their own addresses). Instead you have some DIP switches to change the addressing behavior.
I tried to format the drives directly but they are not lists as devices such as ct1sd1 etc. and so this is not possible.
I have installed Sun Solaris 10 but could not communicate and reported inability to use rdriver and rdnexus and after reading a number of reports that driver hooks had been removed from the kernel in Solaris 10 I have installed Solaris 9.That's fine. You can ignore them. Neither the A1000 nor D1000 require those drivers. You should still be able to use 'rm6' or the CLI tools to interact with an A1000.
On both occasions I installed a number of RAID Manager 6.1.1 control packs, namely SUNWosafw, osar, osau, osamn and vtsse direct from my CD here.
I commanded dr_hotadd.sh to take up the challenge but it failed to communicate.
I added a number of Rdac amendments to rparams in /etc/osa but this did not resolve the issue.
I have tried to call probe-scsi-all after doing a reset-all from the OBP but this fails to report anything. I presume this is because the unit is connected by the interface card rather than a direct scsi disk.If the controller doesn't support the OBP environment, then yes, you won't see anything then.
dmesg pipe grep scsi reports:
unknown scsi sd0 at uata0 target 2 lun 0So that might be a single LUN from an A1000 controller. If the selector switch in the back is set to '2', then it's even more likely.
Darren

Sun ultra 80 Elite 3d hardware issue.Won't boot

Similar Messages

Maybe you are looking for