Sunfire 480R + boot command does not boot from disk

Hi All,
I'm trying to work out why when I type ok>boot
the server keeps booting off the network. It's almost as it does not find any disks and then since diag-device is set to net it tries that instead. The same happens even if I do an init 6 or reboot from solaris??
the output from eeprom looks like:
# eeprom
test-args: data not available.
diag-passes=1
local-mac-address?=false
silent-mode?=false
scsi-initiator-id=7
oem-logo: data not available.
oem-logo?=false
oem-banner: data not available.
oem-banner?=false
ansi-terminal?=true
screen-#columns=80
screen-#rows=34
ttya-rts-dtr-off=false
ttya-ignore-cd=true
ttya-mode=9600,8,n,1,-
output-device=ttya
input-device=ttya
auto-boot-on-error?=false
load-base=16384
auto-boot?=true
boot-command=boot disk
diag-file: data not available.
diag-device=net
boot-file: data not available.
boot-device=/pci@9,600000/SUNW,qlc@2/fp@0,0/disk@w500000e010f124c1,0:a rootmirro
r disk net
use-nvramrc?=true
nvramrc=devalias rootmirror /pci@9,600000/SUNW,qlc@2/fp@0,0/disk@w500000e010f232
61,0:a
security-mode=none
security-password: data not available.
security-#badlogins=0
fcode-debug?=false
diag-out-console=false
post-trigger=error-reset power-on-reset
diag-script=normal
diag-level=min
diag-switch?=false
obdiag-trigger=error-reset power-on-reset
error-reset-recovery=boot

Hello,
Sun Fire 480R ?
Maybe Fire v480 ?
This is device path for the two internal disks (per InfoDoc 21216):
Disk 1 /pci@9,600000/SUNW,qlc@2/fp@0,0
Disk 2 /pci@9,600000/SUNW,qlc@2/fp@1,0
These are your current settings in the OBP
boot-device=/pci@9,600000/SUNW,qlc@2/fp@0,0/disk@w500000e010f124c1,0:a rootmirror disk net
nvramrc=devalias rootmirror /pci@9,600000/SUNW,qlc@2/fp@0,0/disk@w500000e010f23261,0:a
Both point the the same first slot (location in the fc-al backplane), but use different WWNs.
Use show-disks to display the available disks and re-assign the boot-device accordingly.
Michael
P.S.: I just noticed that you never provided feedback in previous posts.

Similar Messages

HT4840 Boot camp does not boot to Windows 7 disk after completing disk partition - white blank screen

After completing the partitionning of the hard disk, the iMac reboots but nothing happens. The system does not boot from the Windows 7 disk.
A blank screen appears and that's all.
I have tried to manually boot from the disk by pressing the <Alt> kei will restarting the iMac. The system display the option of booting from the iMac hard disk or the Windows 7 disk. Seelcting the Windows 7 option does noting.
Thanks in helping me find a solution to my boot problem.
Danarc54

Are using a 64 bit version or a 32 bit version of Windows?
I'm not up on the iMacs but according to this article you may not be able to use 64bit Windows.

MDT 32bit boot image does not boot type 2 virtual machine in hyper-v

I created a type 2 virtual machine on a windows server 2012 R2 and tried to boot it with MDT 32 bit (x86) boot media and it will not boot.
Same media works if I use type 1 virtual machine .
Is this expected behavior ?
Thanks

Hi,
Yes as Gen 2 machines only nsupports only x64 os and the following OS:s
Windows Server 2012
Windows Server 2012 R2
64-bit versions of Windows 8
64-bit versions of Windows 8.1
-- My System Center blog ccmexec.com -- Twitter
@ccmexec

Deleting in aperture does not delete from disk

When deleting masters in Aperture 3.5.1 it does not delete the files from the disk.
I'm using a WD MyBook USB Drive formatted for MAC OS.
I only use referenced masters to save space with the Aperture Library.
Any help to get Aperture to delete files fully, or a way to find a couple years worth of not deleted files on the drive
(e.g. find all files in a folder on the drive that are not in Aperture), would be very welcomed.
thanks
- omaether

Hi,
As I want a clean system, I conducted a series of extra tests to understand why the "delete picture version" did not work.
I can now say that it was related to this second volume (disk) I added in my laptop, which had, for an unknown reason, a permissions issue.
Note that it's impossible to automatically check the volume permissions on a non-bootable partition!
The impact of this permission problem is that the Trash is not working on this volume.
I'm sorry that Aperture didn't mention this (delete) error anywhere during my troubleshooting, as it could have saved me a lot of time!
So here's how to detect and fix:
Create a folder or file next to your library on this volume, then try to delete this empty folder/file.
At this time, it won't be moved to the Trash, but Finder proposes to delete it directly. Don't.
First open this other disk volume with Finder using the "Get Info" (CMD-I) and go at the bottom of the window.
Enable the option "Ignore ownership on this volume" (your password may be needed to unlock this feature first).
Check if the Trash is now working by deleting this empty folder/file. If you did the right operation, it should be placed in the Trash.
Now the permission issue is fixed, try again to delete your pictures from Aperture, and they will be moved automatically to the Trash.
Cheers

I've downloaded Windows 7 onto my USB drive and Boot Camp does not recognize the disk.

Following the Apple Support manual, I've initiated the creation of a partition and downloaded Windows 7 from Microsoft's online store to a USB disk. When I attempt to initiate the creation of my partition to install Windows 7, I receive a notification that my installer disc could not be found.
Thanks in advance!

Welcome to the Apple Support Communities
If your Mac has got the SuperDrive, you can't install Windows from a USB disk

Reset Password - System does not boot from DVD

My System: Macbook Pro - 2Ghz Intel Core Duo - OS X - 10.6.8
Hi everyone,
i forgot my password. So i want to boot from install DVD to reset the password. Unfortunately my macbook pro does not boot from DVD (10.6.3).
I press c all the time...but sometimes the macbook pro throws the DVD out...and sometimes nothing happens.
The DVD drive is working fine...
Any other idea?
Thanks in advance.
Fabian

So when you boot holding option it shows a padlock with a password field? Is that correct?
In that case we're talking about the firmware password, which you can't reset via the install disk. There is only one way to do this, I'm not certain if one is allowed to divulge that information publicly - might want to try googling "reset firmware password"

MSI P6N SLI V2 does not boot up from cd/dvd and few other problems

HI
I just bought a computer P6N SLI V2 + E6750. It has following problem. It does not boot from cd.
I have Sata HD. CD/DVD is installed to IDE as a master.
I have done settings in bios so that First boot is cd/dvd and second is sata HD. Anyhow it still goes to the hd and stars windows.
I was only able to boot up from cd when I disabled hd from boot sequency. Meaning I left only cd/dvd there.
Hopefully you pro's can help me.
Then there is another problem. Windows is telling me that it found new pci device. I do not know what device. I have only Graphig card (geforce 8800 gts) installed into pci-E. Drivers and software are also installed, I assume proberly. How to find out what windows thinks it found.
Third problem is onboard soundcard. I cannot get any sound out from the machine. I have downloaded driver from realtek, but still no sound.
Unfortunatelly I do not have original software for motherboard. Only the latest from MSI website.
Hopefully someone can help me.
thanks.

About bootup, i dont know yet.
To find out what windows found, look in devicemanager.
To go there go to controlpanel, system then choose devicemanager.
There you can see what's installed.
Last, your soundcards needs to be enabled in bios, under integrated peripherals there should be a line with "onboard sound", enable this and sound should work, unless its broken.

Satellite P840/016 does not boot from CD or DVD

Using F2 enabled the BIOS to boot from optical drive, saved and re-started. Finds the bootable CD created from the same laptop using the repair disc from Windows 7 recovery but does not boot.
Tried Ubuntu DVD which works as boot disk on all other laptops - still does not boot.
Changed the setting in BIOS to non-secure - same problem.

Thanks - tried this pressing F12. Message appears on the screen to press any key to boot from DVD. Key pressed, the DVD is read and then delay with blank screen. The laptop goes back to start screen and than goes to boot from the HDD. Also tried making USB as bootable. Pressed F12 and selected USB as boot device. Reads the USB and after a period of time boots from HDD.
Checked DVD driver - it is the latest.
Operating system is Windows 8 pro.
RAM is 8GB, processor is I7 and HDD is 1 TB. Laptop is only 3 weeks old

HT4061 I have an iphone 5s, does not boot, blinking white screen with black logo, when trying itunes restore from mac and pc, error code 4013 which is usb error, any ideas?

I have an iphone 5s, does not boot, blinking white screen with black logo, when trying itunes restore from mac and pc, error code 4013 which is usb error, any ideas? Does a totally dead battery have that effect? I have had it plugged in to a computer overnight, but maybe does not charge when totally dead?
Please help, thanks in advance all1

Hi eggroll77,
Welcome to Apple Support Communities.
That alert codes does suggest there is a USB related issue. If you haven’t already, try the troubleshooting suggestions in the article linked below.
iOS: Restore errors 4005, 4013, and 4014
I hope this helps.
-Jason

Satellite A105 WIN XP does not boot or load...

Ok, so my wife's laptop has a boot issue. Model is A105-S4284
The Toshiba/Phoenix screen loads, but does not boot/load XP. It gives a black screen, then sits for a few secs and restarts. it will continue this loop indefinetely as far as I can tell. When this happened, she complained that it has been taking longer for it to boot into XP recently. (Wish she had told me before)
I can get to BIOS system utilites, Boot menu, and can access F8/Win Advanced options boot choices. I have tried the following:
Safe Mode
Safe Mode w/command prompt
Last known GCFG
Disable Auto restart on failure
I have also done a battery pull and unseated the memory, even swapping left/right, and attempted boot from just one mempry module, all with no change.
Apparently her DVD/optical drive is toast (apparently has been) so I can't do a recovery disc, but I did make a recovery USB drive. No dice there either.
What have I not done? Since I can access the adv. opt. menu it seems winXP is still there. most likely she shut it down while XP was installing something, and now there is some type of error in the registry or somewhere, but I can't seem to recall or remember what my next steps would be to gain access to I can try to clean it up and recover.
I would do a complete wipe and start from scratch, but her entire work portfolio is on the HDD and she (foolishly) has not backed it up, at least not recently. Is my best bet to get an outboard drive enclosure and set the jumpers to slave, so I can attempt to recover the data that way?
I'm a bit stubborn, and know my way around a computer, and I refuse to give up and drop it off at the geek squad.
Please help!

Satellite A105-S4284
her entire work portfolio is on the HDD
First things first. You should rescue the files.
Remove the hard drive and place it in an enclosure accessible from a desktop via USB.
-Jerry

IMac Does not boot past Gray Screen

iMac does not boot past Gray Screen. 2008 24" Intel iMac running Mountain Lion with 1TB hard drive.
Problem started yesterday while I was web surfing, and my iMac frooze and shutdown. I rebooted and could only get as far as the gray screen.
On bootup the following things happen:
Startup tone
Gray screen with Apple, and gear spins below Apple.
Once the gear stops spinning, nothing happends.
Troubleshooting steps I have tried:
removed all devices connected to iMac and rebooted, but same symptons occur.
booted into Safe mode and run disk utilites.
     Disk Utilities found no errors on the drive, but did find two permission issues that it was able to fix.
          First permission issue:
                   "Group differs on library; Should be 0; group is 80"
          Second permission issue:
                    "Permissons differ on library; Should be drwxr-xr-x; They are drwxrwxr-t"
Disk Utilities says it fixes these issues and then I reboot, but get the same problem.
I reboot back into Safe Mode and run Disk Utilities and it discovers the same problems listed above with Permissions. It says it fixes them, I reboot, but the same problem occurs. Its as if we are stuck in some sort of loop process.
Booted into Single User Mode and ran the following command:
     /SBin/fsck -fy   it reports back, Volume Apprears to be ok.
I reboot, same issue !
Performed SMC Reset, Rebooted, same issue
Performed PRAM Reset, Rebooted, same issue.
Booted into Recovery Partitioin (Command R) and ran disk utilities. It found the same permission issues listed above. It fixed them. I rebooted. Same problem still.
While in safe mode, I preformed a full time machine backup.
I am out of ideas. Any help would be greatly appreciated.

Hello,
I reboot back into Safe Mode and run Disk Utilities and it discovers the same problems listed above with Permissions.
You can ignore repeated "fixes" it's not really a problem, if it says completed repairs that's all that's needed.
Luckily it boots in Safe Mode, here's basically the steps to try to find out what it is...
One way to test is to Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, Test for problem in Safe Mode...
PS. Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive
Reboot, test again.
If it only does it in Regular Boot, then it could be some hardware problem like Video card, (Quartz is turned off in Safe Mode), or Airport, or some USB or Firewire device, or 3rd party add-on, Check System Preferences>Accounts>Login Items window to see if it or something relevant is listed.
Check the System Preferences>Other Row, for 3rd party Pref Panes.
Also look in these if they exist, some are invisible...
/private/var/run/StartupItems
/Library/StartupItems
/System/Library/StartupItems
/System/Library/LaunchDaemons
/Library/LaunchDaemons
Though I'm suspecting some corruption to your OS at the moment.

Server does not boot

Dear Sir
I have use Main Server PowerEdge 1900 with operating system SQL Server 2008 r2 the main server does not boot after reading all system files a message appear choose recovery mood
1- restore from system image recovery
2- Command Prompt
i have important data in it and a database runing in the server machine how can i boot the server properly without having any backup.
How can i pick up data from command prompt.

The bad part is that you do not have backups. The good part is that you can recover your data by using a bootable device and copying them to another location.
However, for the DB part, you might want to ask them here: https://social.technet.microsoft.com/Forums/windowsserver/en-US/home?forum=sqldisasterrecovery&filter=alltypes&sort=lastpostdesc
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

Cisco Nexus 5596 does not boots up after NX-OS upgrade 5.1.3.N1.1 to 6.0.2.N2.5 [CSCun66310]

Hello Friends,
Just want to save your precious time & effort, while doing Nexus 5596 upgrades so wanted to share some useful info which you can have a look prior to your upgrades of Cisco Nexus 5596 device.
I recently ran into trouble when upgarding one of datacenter switch Nexus 5596 does not boots up and after investigation from Cisco TAC it comes out to be Bug documented below.
https://tools.cisco.com/bugsearch/bug/CSCun66310/?reffering_site=dumpcr
My Upgrade path of device was : 5.1(3)N1(1)  to 6.0(2)N2(5).
Since this upgarde involves upgrade of Bios and Power sequensor, I was having some doubts to get this succesfully upgraded, But there was more twist involved in this upgrade which I came to know after contacting Cisco TAC for my died Nexus 5596 device and got info that if you have below impacted version in your Nexus 5596 device and you are planning to do Upgrade, then you migh RUN into this serious BUG aftre which device won't come up at all and only Option left is to replace with RMA device.
PID                          Impacted                   Hardware versions      Updated Versions
UCS-FI-6296UP                                            1.0                                       1.1
N5K-C5596UP                                              1.0                                        1.1
N5K-C5596T                                                 1.1                                         1.2
You can check hardware version using below command from your device.
5596# show sprom sup | inc H/W
H/W Version     : 1.1
So please be carefull when planning your Nexus 5596 upgrade and verify above things as this Bug is not present anywhere in Upgrade docuemntations unfortunately.
Hope this will help and save someone's precious Time.

Today "upgraded" our switch (N5k-C5596UP) to from 5.1(2)N1 to 7.0(5) and after reboot no life from the switch either. Even no console response. show sprom sup | inc H/W shows 1:0.
Only thing we could do is RMA the switch. So what must I do with these switches? Have still to do 3 of them.

New MBP i5 does not boot after hard disk swap

Hi there,
I received my new i5 MBP today. After booting it once with the installed HDD to check if it's ok, I exchanged the hard disk for the one in my Late 2008 Macbook Pro. After doing this, my Late 2008 Macbook Pro boots fine with the (new) hard disk from the new i5 MBP, but the i5 MBP does not boot with my old hard disk.
To give you some details:
- I have installed 10.6.3 on the (old) hard disk that's not booting.
- The i5 MBP boots fine from the installation DVD
- Disk utility finds and can read my hard disk, no errors
- PRAM NVRAM reset did not help
- when booting in safe mode, I can see the system stop booting after or while loading Extensions.mkext
My guess is, it tries to boot and load the wrong Extensions for the new system (CPU? GPU?). I have no idea how to fix this.
Any help would be greatly appreciated!

Focx,
Welcome to Apple Discussions.
Inserting the drive from an earlier model MBP will probably not work. The version of the system you have on that HD is designed for earlier hardware so when you put in in your new machine it's going to be recognized. What I'd recommend is re-installing the disk that came with the new machine and of course putting the 2008's disk back in the old machine. Then use Migration Assistant on the new machine and migrate your data from the old machine into the new machine.
This will provide a much more stable system and should work just fine.
Regards,
Roger

Satellite L745D-S4214 Does not boot; HDD recovery partition not working

I tried to apply the recent windows 7 updates and my laptop no longer boots. I tried to press F12 and select the HDD Recovery partition, but it does not boot regardless. There is a message that it does not communicate to a specific device. I believe the address called out was 0xc0000e9, but I am going by memory. I never created a recovery CD because I thought I was covered by the HDD partitions. This was purchased on 10/26/2012, so it should still be under warranty.
PLEASE HELP!

Hi I'm going to assume that your recovery works like mine and that the recovery partition is still good and not corrupted.
Shut down your PC. Press F12 and select HDD recovery. Click enter. This should start the recovery from the hidden recovery partition.
PS I would advise you to make the recovery discs or USB recovery Try this first.
Perform a power cycle
Even when your laptop is off and unplugged, residual power can still be held in some components. While this is normal, clearing it can help with boot problems. Perform these steps to complete what’s called a power cycle.
Ensure the laptop is turned off.
Unplug the laptop's AC power cable.
Remove the battery (if the model has a removable battery).
Unplug all wires or peripherals. This includes CDs, DVDs, USB sticks, mice, printers, and any other accessories.
Hold down the power button for thirty seconds.
Reattach the battery.
Connect the AC adaptor to the power socket that was confirmed to be working in the first step.
Connect the other end of the AC adaptor to your computer.
Try starting the computer.
If your laptop starts normally now, you're done!
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.

Sunfire 480R + boot command does not boot from disk

Similar Messages

Maybe you are looking for