SunFire 480R - Solaris 10 New Install

Immediatly after the probing of all the NIC cards I get:
message overflow on /dev/log minor #6 -- is syslogd(1M) running?
message overflow on /dev/log minor #6 -- is syslogd(1M) running?
message overflow on /dev/log minor #6 -- is syslogd(1M) running?
message overflow on /dev/log minor #6 -- is syslogd(1M) running?
message overflow on /dev/log minor #6 -- is syslogd(1M) running?
It never ends..
I've flashed to the latest OBP.
I'm installing from 1-06 DVD.
Thoughts?

What type of DVD are you using ?
could it be ODD-DVD SD-C2732 ? If so you should have its FIRMWARE version to 1055. Patch 120364-03

Similar Messages

Solaris 10 new install and new (?) hard disks

Ok, so I started a solaris 10 install (5/08) on a sparc enterprise 3000 server. I first did the install on 2 brand new 10.7k rpm seagate cheetahs and I was able to install, copy layout to the target disk, configure Raid 1 mirror, was able to boot from the mirror, so on and so on, basically everything ran accordingly. Then I was told that there was a batch of brand new 15k rpm cheetahs and that I should use those. As I rebooted with the new drives, I got the "magic label" warning, so basically I re-labeled them. I ran install and everything installed as before, BUT when I went to SMC to copy the disk layout to the target drive, the only drive present is the target drive (c0t1d0). The drive c0t0d0 does not show. Format does show both drives. Now, if I reboot without drive c0t1d0 and immediately go to SMC/Disks, the drive c0t0d0 is there. What is causing that behavior? Do the drives already have labels and partition info that need to be cleared or redone? I have already tried to re-label and re-partition c0t1d0 identically to c0t0d0 and that does not seem to have an effect. I tried running fdisk /dev/rdsk/c0t1d0 and I get the " cannot stat device /dev/rdsk/c0t1d0" message. Is there a way to completely wipe out the entire drive c0t1d0 through solaris? Any suggestions? Thanx in advance.
Erickc

ok, so I was able to copy the c0t0d0 layout to c0t1d0 and that went trough. I verified through format>partition that both drives had identical partition information. I created metadb's to both drives in the specific slices and that was ok. Now here's what I get when I try to create a mirror...
metainit -f d1 1 1 c0t0d0s0
d1: concat/stripe is setup
metainit d2 1 1 c0t1d0s0
metainit: c0t1d0s0: overlaps with c0t0d0s0 which is mounted as "/"
On my first install I was able to create the mirror without a problem. What would be the cause?
Thanx in advance for any suggestions.

New install of SJS Ent 8 on Solaris, can't start Application Server 8.1

Hello,
Appreciate in advance your help.
Just downloaded and installed SJS 8.1 on a new Sun Solaris 10 box. I'm able to run the IDE and have started the Tomcat server, but when attempting to start the SJS 8.1 application server, I get:
The Sun Java System Application Server 8.1 could not start.
More information about the cause is in the Server log file.
Possible reasons include:
- Port conflicts. (use netstat -a to detect possible port numbers already used)
- Incorrect server configuration
- Corrupted Deployed Applications
The problems are:
- There is no server.log file in the expected directory at /opt/sun/jstudio_ent8/AppServ8.1UR2/domains/myDomain1/logs
- I ran netstat -a, but could glean no useful information
- I have not modified the server configuration since the new install
- I have not deployed my application (since I can't start the server).
Forgive my ignorance since I'm not a Solaris expert. I would greatly appreciate your assistance.

No difference in server.log after setting level="FINEST".
Don't know if it would help, but the contents of my server.log file follow:
[#|2006-09-25T15:39:46.485-0400|INFO|sun-appserver-pe8.1_02|javax.enterprise.tools.launcher|_ThreadID=10;|
/opt/sun/jstudio_ent8/jdk1.5.0_04/bin/java
-client
-Xmx512m
-XX:NewRatio=2
-Dcom.sun.aas.defaultLogFile=/opt/sun/jstudio_ent8/AppServ8.1UR2/domains/myDomain1/logs/server.log
-Djava.endorsed.dirs=/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/endorsed
-Djava.security.policy=/opt/sun/jstudio_ent8/AppServ8.1UR2/domains/myDomain1/config/server.policy
-Djava.security.auth.login.config=/opt/sun/jstudio_ent8/AppServ8.1UR2/domains/myDomain1/config/login.conf
-Dsun.rmi.dgc.server.gcInterval=3600000
-Dsun.rmi.dgc.client.gcInterval=3600000
-Djavax.net.ssl.keyStore=/opt/sun/jstudio_ent8/AppServ8.1UR2/domains/myDomain1/config/keystore.jks
-Djavax.net.ssl.trustStore=/opt/sun/jstudio_ent8/AppServ8.1UR2/domains/myDomain1/config/cacerts.jks
-Djava.ext.dirs=/opt/sun/jstudio_ent8/jdk1.5.0_04/jre/lib/ext:/opt/sun/jstudio_ent8/AppServ8.1UR2/domains/myDomain1/lib/ext
-Djdbc.drivers=com.pointbase.jdbc.jdbcUniversalDriver
-Djavax.management.builder.initial=com.sun.enterprise.admin.server.core.jmx.AppServerMBeanServerBuilder
-Dcom.sun.enterprise.config.config_environment_factory_class=com.sun.enterprise.config.serverbeans.AppserverConfigEnvironmentFactory
-Dcom.sun.enterprise.taglibs=appserv-jstl.jar,jsf-impl.jar
-Dcom.sun.enterprise.taglisteners=jsf-impl.jar
-Djavax.xml.parsers.SAXParserFactory=com.sun.org.apache.xerces.internal.jaxp.SAXParserFactoryImpl
-Dcom.sun.aas.configName=server-config
-Dorg.xml.sax.parser=org.xml.sax.helpers.XMLReaderAdapter
-Ddomain.name=myDomain1
-Djmx.invoke.getters=true
-Djavax.xml.parsers.DocumentBuilderFactory=com.sun.org.apache.xerces.internal.jaxp.DocumentBuilderFactoryImpl
-Dcom.sun.aas.promptForIdentity=true
-Dorg.xml.sax.driver=com.sun.org.apache.xerces.internal.parsers.SAXParser
-Dcom.sun.aas.instanceRoot=/opt/sun/jstudio_ent8/AppServ8.1UR2/domains/myDomain1
-Djavax.xml.transform.TransformerFactory=com.sun.org.apache.xalan.internal.xsltc.trax.TransformerFactoryImpl
-Dcom.sun.aas.domainName=myDomain1
-Djava.util.logging.manager=com.sun.enterprise.server.logging.ServerLogManager
-Dproduct.name=Sun-Java-System/Application-Server
-Dcom.sun.enterprise.overrideablejavaxpackages=javax.faces,javax.servlet.jsp.jstl,javax.xml.bind,javax.help
-Dcom.sun.aas.configRoot=/opt/sun/jstudio_ent8/AppServ8.1UR2/config
-Djava.library.path=/opt/sun/jstudio_ent8/jdk1.5.0_04/jre/lib/i386/client:/opt/sun/jstudio_ent8/jdk1.5.0_04/jre/lib/i386:/opt/sun/jstudio_ent8/jdk1.5.0_04/jre/../lib/i386:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib:/usr/lib/lwp::/usr/lib
-Dcom.sun.aas.instanceName=server
-Dcom.sun.aas.processLauncher=SE
-cp
/opt/sun/jstudio_ent8/jdk1.5.0_04/lib/tools.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-rt.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/j2ee.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/activation.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/mail.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-cmp.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/admin-cli.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-admin.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-jstl.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/commons-launcher.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/commons-logging.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/j2ee-svc.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/jax-qname.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/jaxr-api.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/dom.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/jaxr-impl.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/jaxrpc-api.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/jaxrpc-impl.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/relaxngDatatype.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/saaj-api.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/saaj-impl.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/xsdlib.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/jmxremote.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/jsf-api.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/jmxremote_optional.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/jsf-impl.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/rmissl.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/xalan.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/xercesImpl.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-assemblytool_ja.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-cmp_ja.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-rt_ja.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/commons-launcher_ja.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/deployhelp_ja.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/j2ee_ja.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-assemblytool_zh.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-assemblytool_zh_CN.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-cmp_zh.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-cmp_zh_CN.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-rt_zh.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-rt_zh_CN.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/commons-launcher_zh.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/commons-launcher_zh_CN.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/deployhelp_zh.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/deployhelp_zh_CN.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/j2ee_zh.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/j2ee_zh_CN.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-assemblytool_ko.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-cmp_ko.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-rt_ko.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/commons-launcher_ko.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/deployhelp_ko.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/j2ee_ko.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-assemblytool_fr.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-cmp_fr.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-rt_fr.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/commons-launcher_fr.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/deployhelp_fr.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/j2ee_fr.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-assemblytool_es.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-cmp_es.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-rt_es.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/commons-launcher_es.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/deployhelp_es.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/j2ee_es.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-upgrade.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/appserv-ext.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/install/applications/jmsra/imqjmsra.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/imq/lib/jaxm-api.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/imq/lib/fscontext.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/lib/ant/lib/ant.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/pointbase/lib/pbclient.jar:/opt/sun/jstudio_ent8/AppServ8.1UR2/pointbase/lib/pbembedded.jar
com.sun.enterprise.server.PEMain
start|#]
I do notice that the class path references jdk1.5.0_04. When installing SJS I selected the separately installed jdk1.5.0_07. Could that be causing the problem?
You have great patience.

Moving disks while maintaining Solaris 10 install from one v240 to another.

Hi,
I want to move a Solaris 10 install from a sunfire v240
with a single cpu to another sunfire v240 with dual cpu's. Here are the
details of the hosts as well as configuration.
I have 2 sunfire v240's. One has a single 1 Ghz cpu and the second has
dual 1.5 Ghz cpu. I want to move the disks of the single cpu host to
the host with dual cpu's. I want to keep the installed version of
Solaris 10 intact. The installation of Solaris is split across 2
mirrored disks, i.e. 4 disks in total. I am using Suns volume manager
for mirroring and also have one files system mirrored with zfs.
The questions I have are the following:
1) Can I simply shut down the servers and swap the disks to the
destination host, in the same disk slots? The controllers the disks are
on line up and are the same between the 2 hosts.
2) Will the kernel pickup the changes moving from a single 1 Ghz cpu to
dual 1.5. Ghz cpu's with out any problems? Will the kernel pickup the
faster cpu's speeds. i.e. will it know it is now running dual 1.5. Ghz
cpu opposed to a single 1 Ghz?
3) Would we have to break the mirroring on the OS before shutting it
down?
4) As another option, instead of swapping disks, could we swap the
cpus? Move the dual 1.5. Ghz cpu's to the other host? Will the
motherboards read the updates of the cpu or are their jumper settings we
would need to update?
Thanks for your help.

Box A
Sparc Solaris 9, Oracle 10g
Box B
Solaris 10 x86, Oracle 11g
I know there are many factors, but I'm pretty new to both unix & oracle, so I >needed some general steps to get me started. You have many options.
Since you're in 10g, Have the Target Database created in Solaris 10 x86, Oracle 11g.
you can use,
RMAN - Cross platform Transportable Tablespaces.
Datapump Export and Datapump import.
Read the following:
How To Use RMAN CONVERT DATABASE for Cross Platform Migration - 413586.1
http://download-uk.oracle.com/docs/cd/B19306_01/backup.102/b14191/dbxptrn.htm
http://www.oracle-base.com/articles/10g/OracleDataPump10g.php
http://www.oracle-base.com/articles/10g/RMANEnhancements10g.php#cross_platform_tablespace_conversion

New Install - ICMP Host Unreachable from gateway

Hi team,
I'm configuring a new solaris x86 box for the first time in a long time and I'm running into a problem that has me stumped.
I just installed Solaris 10 v7 on a P4 Dell box with an intel pro1000 adapter loaded.
Installed using ZFS and install went well. I set a static IP of 192.168.1.70 on a proper 192.168.1.x lan.
After install, everything seems to work fine but cannot ping a FQDN such as www.google.com, etc.
at first, I tried to join a local domain - maxximgroup.com and my computer name is set to sunzilla.
Here's my network config files;
sunzilla is set up with static IP = 192.168.1.70
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.1.70 netmask ffffff00 broadcast 192.168.1.255
ether 0:1b:21:27:56:2c
lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
inet6 ::1/128
e1000g0: flags=2004841<UP,RUNNING,MULTICAST,DHCP,IPv6> mtu 1500 index 2
inet6 fe80::21b:21ff:fe27:562c/10
ether 0:1b:21:27:56:2c
And /etc/hosts shows host name sunzilla associated w/ 192.168.1.70...
# cat /etc/hosts
# Internet host table
::1 localhost
127.0.0.1 localhost
192.168.1.70 sunzilla loghost
And my resolv.conf file shows my internal DNS routers as well as a 3rd I added (4.2.2.2) just in case...
# cat /etc/resolv.conf
domain maxximgroup.com
nameserver 192.168.1.20
nameserver 192.168.1.22
nameserver 4.2.2.2
search maxximgroup.com
I noticed the /etc/defaultrouter file was MISSING... so I created one pointing to my router...
# cat /etc/defaultrouter
192.168.1.1
And finally, I checked the /etc/nsswitch.conf file and it does indeed show hosts & ipnodes --> files & dns ...
# cat /etc/nsswitch.conf
# Copyright 2006 Sun Microsystems, Inc. All rights reserved.
# Use is subject to license terms.
# /etc/nsswitch.dns:
# An example file that could be copied over to /etc/nsswitch.conf; it uses
# DNS for hosts lookups, otherwise it does not use any other naming service.
# "hosts:" and "services:" in this file are used only if the
# /etc/netconfig file has a "-" for nametoaddr_libs of "inet" transports.
# DNS service expects that an instance of svc:/network/dns/client be
# enabled and online.
passwd: files
group: files
# You must also set up the /etc/resolv.conf file for DNS name
# server lookup. See resolv.conf(4).
hosts: files dns
# Note that IPv4 addresses are searched for in all of the ipnodes databases
# before searching the hosts databases.
ipnodes: files dns
networks: files
protocols: files
rpc: files
ethers: files
netmasks: files
bootparams: files
publickey: files
# At present there isn't a 'files' backend for netgroup; the system will
# figure it out pretty quickly, and won't use netgroups at all.
netgroup: files
automount: files
aliases: files
services: files
printers: user files
auth_attr: files
prof_attr: files
project: files
tnrhtp: files
tnrhdb: files
I can ping local IP addresses ...
# ping 192.168.1.1
192.168.1.1 is alive
But not external addresses ...
# ping 67.15.211.8
ICMP Host Unreachable from gateway sunzilla (192.168.1.70)
for icmp from sunzilla (192.168.1.70) to ns1.siteground168.com (67.15.211.8)
ICMP Host Unreachable from gateway sunzilla (192.168.1.70)
for icmp from sunzilla (192.168.1.70) to ns1.siteground168.com (67.15.211.8)
ICMP Host Unreachable from gateway sunzilla (192.168.1.70)
for icmp from sunzilla (192.168.1.70) to ns1.siteground168.com (67.15.211.8)
ICMP Host Unreachable from gateway sunzilla (192.168.1.70)
for icmp from sunzilla (192.168.1.70) to ns1.siteground168.com (67.15.211.8)
^C#
and naturally, I can ping a FQDN either (confirmed to be pingable on a computer on the same lan) ...
# ping mycloud.local
ping: unknown host mycloud.local
Can anyone provide some guidance pls?

Thanks Robert. You were absolutely on the right track. It turns out that in my "rush" to get my new ZFS "toy" up and running, during the install, I gave Solaris a static address but told it to automatically find the gateway. Oops! When solaris 10 installed, it correctly decided that since it had a static IP, it should assign the gateway as itself! So, naturally, when I ran netstat -m, It showed my gateway as myself! 192.168.1.70 sunzilla.
I'm used to running Solaris on a Sparc platform and I'm a bit uncomfortable with reboots and I figured there would surely be a network restart command somewhere. After finding out that things have now changed in Solaris 10 quite a bit from Solaris 8, I just decided to init 6.
After the system came up, everything was happy : -)
So again, thanks to Robert for helping save the day!

New Install of sjsws7U2

Running sjsws7U2 on Solaris 10 SPARC
Did a clean install, messed up setting up a virtual server and now even though I un-installed the "entire" server, a new install now asks for authentication (username/password)
Access Control section (default and es-internal) show that it should be open.
No username/password requirement
How do I turn off the unwanted prompt for username/password
Thanks

Can you send all the ACL files in <server-instance>/config directory. Can you send what request you send to the server and what response you get (using ssltap or ethereal) and can you run Web Server instance in log-level "finest" (modify in server.xml <log-level>finest</log-level>) and send relevant portion of error logs?

Resoring prodution database into new installed sap system

have installed ecc 6.0 with sql server 2008 (sp 1) on windows 2003
server with 64 bit.
My installtion was done sussfully and also i started sap system.It
was working fine. then i took backup from my standalone system .
I restored prodution server database in standalone system and restore
was done successfully.
Then iam trying to login to sap system then it was saying that
dispature was stopped.
first dispatur was in yellow and status running message server
connection ok,dialuge que time 0;00sec,j2ee status info unavailable.
Iam sending screen shots and also related error log files attatched.
Please can you get help from those documents.
I also checked r3trans -d.
C:\Documents and Settings\Administrator>r3trans -d
This is r3trans version 6.14 (release 700 - 12.06.09 - 15:20:00).
unicode enabled version
2EETW169 no connect possible: "DBMS = MSS --- SERER = 'SHURJO' DBNAME = 'PRD'"
r3trans finished (0012).
before doing prodution database restore is compulsary to i have to increase the patch levels of my new installed system
because my prodution server abap& basis patch levels are 19 and my installed system it is only 14.
Please can any body give right way to resolve this problem,
Regards,
Krishna

> before doing prodution database restore is compulsary to i have to increase the patch levels of my new installed system
> because my prodution server abap& basis patch levels are 19 and my installed system it is only 14.
First: It's pointless to first install a full system and then try to overwrite the database with another one.
I would INSTALL the system using the database copy.
This procedure is call "homogeneous system copy" and there's a guide for that available at http://service.sap.com/instguides and also in "Note 151603 - Copying an SQL Server database".
The error message is coming because the database has not the proper users, you'd need to run the STM tool to adapt the users and the environment. Those steps are all described in detail in the guide.
Markus

How to log in to the new installed SAP ABAP instance ?

Dear Experts,
In SAP ERP 2005 installation,
I have done central system installation, Now I need to perform postinstallation steps,
Could you please tell me, how to log in to the new installed SAP ABAP instance and do the post installation?
Regards,
Madhavan K

Hi,
Check the list of post installation steps:
http://www.saptechies.com/post-installation-steps-for-ecc-60/
From my point of view basic post installation steps are:
- Installing SAP License (from http://service.sap.com/licensekeys)
- Setup TMS (STMS)
- Import profiles (RZ10)
- Client Copy (SCC*)
- Create users (SU01)
However further many steps are required as per your requirements. Cehck the link for more detailed steps.
Regards,
Srikishan

Every time I close FF it reverts to new install settings and doesn't retain any settings, I have uninstalled & reinstalled but no change - help

I installed FF and used it without issue, but on loading it for me next session and every subsequent session it reverts to the state it was as a new install including not retaining any settings for loaded extensions. This is a total pain and is likely to lead me to uninstalling if I cannot find a fix soon. I have uninstalled and re-installed and tried re-set but neither has made any difference.

You can check for problems with preferences and try to rename or delete the prefs.js file and possible numbered prefs-##.js files and a possible user.js file to reset all prefs to the default values.
*http://kb.mozillazine.org/Preferences_not_saved

Team Foundation Server 2013 update 4 New Install - Error 503 Service Unavailable for Sharepoint Central Admin

Hello,
I ran a new install of Team Foundation Server and let it install the built in SharePoint pieces on a single server setup. After the install i'm able to access the
http://teamfoundation:8080/tfs/ address without issue but am unable to create a project. When I attempt to create a project I get the following error:
TF30172: You do not have permission to create a new team project (when checking security i'm a member of the project collection administrators and Team Foundation Administrators)
This led me to look at the sharepoint central administration site where I receive the following error:
Error 503 Service Unavailable
I've gone through and validated the identity is set correctly in IIS for the following services:
SharePoint Central Admin v4
SharePoint15AppPool
The SharePoint Web Services Root is set as LocalService instead of the domain user.
The identity domain user is setup as local administrator on the Team Foundation Server. They are all set to use .net v4.0.30319 with integrated Pipeline mode.
Any help would be great!
Thanks!
Eric

Hi Eric,
Thanks for your post.
Please share your detailed team project creation log here.
In your TFS Admin Console>>Extensions for SharePoint Products tab, ensure SharePoint Web Application shows correctly in the right panel. And go to TFS Admin Console>>Application Tier>>SharePoint Web Applications tab, ensure your SharePoint
web application displays in the right panel, then select your SharePoint web application and click Repair Connection, ensure can repair successfully.
In your IIS Manager, select your SharePoint Central Administration V4 site and click Browser:17012(http) in the right panel, check if your SharePoint Central site can be opened successfully or not. If your SharePoint Central site cannot be accessed, I think
this issue relate to your SharePoint site, you should contact SharePoint experts to resolve this issue first. After you resolved this issue and your SharePoint Central Admin site can be accessed correctly, then try to create your team project(within SharePoint
site) again, if there still has issue when creating team project, please share the detailed error message here, we will try to resolve it.
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

New install not accessing existing library on D: drive.

My iTunes library is much larger than my entire SSD I use as a boot volume, so of course I keep it on a second internal hard drive labeled D:.
I just had my system corrupted and all backcup images not read by restore discs, so I had to wipe my C: SSD and re-install my Windows 7, 64-bit OEM from scratch. Now, with a new install of iTunes, I can't seem to get it to recognize my existing library on my D: drive. I've pointed it there in preferences both to the iTunes folder and the iTunes Library folder inside it on the drive. I can open any individual item with iTunes separately and add that to my library separately, but no matter what, this thing just seems to ignore my existing content completely. Nothing shows in my library within the program but the few nonsense songs that came with some software somewhere.
I at first thought it was finding my TV shows, but it turns out that was only on the cloud. I don't want to depend on some cloud server for my content I've bought and paid for when I have it stored in redundant hard drives of my own. I need this to access my content on the drive I've selected for it, including my existing content already there.

OK, I got the menu bar open and found an article in "help" that said to drag the existing library folder into the iTunes window and that got my stuff into the software, but how can I be sure that new purchases go into the proper folder on my D: drive rather than into some C; drive location. I have a terrabyte D: drive that is already red in Windows Explorer and still has more space left than this SSD I'm using as a C: drive had blank.

V6.01, Windows 7, click on icon, "firefox is already running but not responding" Task manager doesn't know about it. I can't quit it or get it to load. Brand new install. What to do?

Brand new Lenovo computer, Windows 7 Home. New install of Firefox 6.0.1, set as default browser, don't launch when I click done. Icon appears in tray. I click the icon, and a message says "firefox is running but not responding. To open a new window, you must first close the existing process, or reboot". It's not obviously running. I can't find a way to make it quit. Task manager doesn't list it as a current application. Uninstall using the control panel uninstall function and then reinstalling gives the same message. Rebooting doesn't fix the problem and gives the same message. Firefox had been working until I tried to update my bookmarks.

No can do. I can delete the current profile and install Firefox, which should create a new blank profile. The message still says "Firefox is already running." I can place my old profile in the proper folder, and Firefox will still be already running. I can't actually use Firefox, because even though the message says it is running, there is nothing on the screen I can access.
After uninstalling Firefox, deleting the two items left in the Programs folder, and deleting the profile again, it still didn't work. I then got frisky and from the Roaming folder I deleted the Mozilla folder which contains the Firefox folder which contains the now empty Profiles folder. That worked, and a new set of folders with a new blank profile were created. So apparently it was the empty folders that never got deleted that were causing the issue.
Thanks for your suggestion. It got me thinking.

New install of Crystal 2013 Server; getting errors

New install of Crystal 2013 Server on Windows 2012R2 Server
In the Connectivity Services; the ConnectionServer32 shows a state of Initalizing, and Disabled
In the Crystal Report Services; the CrystalReports2013ProcessingServer shows a state of Running with errors and Disabled
In the Crystal Report Services; the CrystalReports2013ReportApplicationServer shows a state of Stopped and Enabled
Hovering over Stopped I get "The Executable could not be launched. Possible reasons are insufficient RAM or disk space, or an invalid filepath or working directory. Actual reason: CreateProcess error + 14001, The application has failed to start because its side-by-side configuration is incorrect. Please see the application event log."
Application Event Log Entry:
Log Name:      Application
Source:        BusinessObjects_cms
Date:          4/21/2014 11:43:12 AM
Event ID:      33017
Task Category: General
Level:        Warning
Keywords:      Classic
User:          N/A
Computer:      DBH-TCRYSTAL01.sbcounty.gov
Description:
Unable to contact server DBHTCRYSTAL01.ConnectionServer32 on machine DBH-TCRYSTAL01.sbcounty.gov to perform status notification. Please check the server's system log for errors.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
    <Provider Name="BusinessObjects_cms" />
    <EventID Qualifiers="0">33017</EventID>
    <Level>3</Level>
    <Task>1</Task>
    <Keywords>0x80000000000000</Keywords>
    <TimeCreated SystemTime="2014-04-21T18:43:12.000000000Z" />
    <EventRecordID>32081</EventRecordID>
    <Channel>Application</Channel>
    <Computer>DBH-TCRYSTAL01.sbcounty.gov</Computer>
    <Security />
</System>
<EventData>
    <Data>DBHTCRYSTAL01.ConnectionServer32</Data>
    <Data>DBH-TCRYSTAL01.sbcounty.gov</Data>
</EventData>
</Event>
System Event Log Entry:
Log Name:      System
Source:        Microsoft-Windows-DistributedCOM
Date:          4/21/2014 7:49:07 AM
Event ID:      10016
Task Category: None
Level:        Error
Keywords:      Classic
User:          SYSTEM
Computer:      DBH-TCRYSTAL01.sbcounty.gov
Description:
The application-specific permission settings do not grant Local Launch permission for the COM Server application with CLSID
{05D1D5D8-18D1-4B83-85ED-A0F99D53C885}
and APPID
{AD65A69D-3831-40D7-9629-9B0B50A93843}
to the user NT AUTHORITY\SYSTEM SID (S-1-5-18) from address LocalHost (Using LRPC) running in the application container Unavailable SID (Unavailable). This security permission can be modified using the Component Services administrative tool.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
    <Provider Name="Microsoft-Windows-DistributedCOM" Guid="{1B562E86-B7AA-4131-BADC-B6F3A001407E}" EventSourceName="DCOM" />
    <EventID Qualifiers="0">10016</EventID>
    <Version>0</Version>
    <Level>2</Level>
    <Task>0</Task>
    <Opcode>0</Opcode>
    <Keywords>0x8080000000000000</Keywords>
    <TimeCreated SystemTime="2014-04-21T14:49:07.818690400Z" />
    <EventRecordID>8228</EventRecordID>
    <Correlation />
    <Execution ProcessID="668" ThreadID="804" />
    <Channel>System</Channel>
    <Computer>DBH-TCRYSTAL01.sbcounty.gov</Computer>
    <Security UserID="S-1-5-18" />
</System>
<EventData>
    <Data Name="param1">application-specific</Data>
    <Data Name="param2">Local</Data>
    <Data Name="param3">Launch</Data>
    <Data Name="param4">{05D1D5D8-18D1-4B83-85ED-A0F99D53C885}</Data>
    <Data Name="param5">{AD65A69D-3831-40D7-9629-9B0B50A93843}</Data>
    <Data Name="param6">NT AUTHORITY</Data>
    <Data Name="param7">SYSTEM</Data>
    <Data Name="param8">S-1-5-18</Data>
    <Data Name="param9">LocalHost (Using LRPC)</Data>
    <Data Name="param10">Unavailable</Data>
    <Data Name="param11">Unavailable</Data>
</EventData>
</Event>
I also have second Windows 2012R2 Server / Crystal 2013 Server install that is working just fine and the only difference is it is not a member of the Domain.
Barry Streets
[email protected]
510-238-2727 ext 2780

In addition to checklists provided by Josh; I would suggest you to perform a repository scan of the system to identify whether any objects were not installed properly and there might be a possible corruption. Use the link mentioned below to perform repository scanning.
How to use Repository Diagnostic Tool - Business Intelligence (BusinessObjects) - SCN Wiki
You can try to repair the install. Also as this is a new install you can directly go for re-installing the software.
PS: Try to re-download the software from the service market place rather than copying the installer from existing one.

Oracle Upgrade vs New Install

I have a client who wants to 'merge' 2 separate instances into a single instance in 11.5.10. The 2 separate instances are at different application and database levels, but do have commonalities, such as the COA structure. Part of the single instance project requires that the current CoA structure be changed from the current model. My impression and experience has told me this is a new install with a data migration from the 2 instances. Would that be the consensus of this group as well? Would there be any benefit to upgrading the 'newer' instance, creating a new SOB with the new structure, and then migrating data from the 'older' instance into the 'newer'/upgraded instance, which then serves as the single instance. Part of the migrations however, would BOTH require data conversion and mapping from the old COA to the new COA...

Any specefic Reasons why Multi Org can not be used here

IPhoto won't open after new install and restore of back-up

Hi guys
My hard drive just died (for the second time in 6 months!) so I have just gotten the computer back with a new drive. I did a new install of Tiger from my original install CDs, did the download thing to get all the updates, and ran a "restore" from my external drive using iBackup (http://www.grapefruit.ch/iBackup//index.html) to restore all my previous system settings, documents, etc. So far this seems to have worked well, a couple of 3rd party applications didn't re-install - specifically Neo Office and WiFind - but I was able to manually install those and everything seems to be working fine.
Except iPhoto. It won't open. When I click the dock icon it bounces once and does nothing. No little arrow under it or anything. Nothing at all happens when I click the icon in Finder (in the Applications folder). When I searched it in spotlight it told me there was a file called iphoto.crash.log, so I went and had a look at that hoping it would tell me the problem, but I don't understand it. I'm not particularly good at the behind the scenes stuff with computers.
Wondering what I should do now - if someone can perhaps interpret the log file and find the issue if that would help, or if I should uninstall and re-install iPhoto by itself (and if so, how?), or if there is something else that may be causing the issue. I noticed there are a few files relating to it when I search with spotlight but I don't know which of them might be relevant. I could post a screenshot if that is allowed, or post the log file if it would help?
Thanks in advance for any advice or help!
Regards,
Chloë

400 Updates???
Did you Repair Permissions before & after each one?
The usual reason why updates fail or mess things up, or things don't load/run, is if Permissions are not fixed before & after every update, with a reboot... you may get a partial update when the installer finds it doesn't have Permissions to change one obscure little part of the OS, leaving you with a mix of OS versions.
Some people get away without Repairing Permissions for years, some for only days.
If Permissions are wrong before applying an update, you could get mixed OS versions, if Directory is the slightest messed up, who knows!
If many Permission are repaired, or any Directory errors are found, you may need to re-apply some the latest/biggest updates again, or even do an A&I if you have enough free disk space.
The combo update for PowerPC-based Macs...
http://www.apple.com/support/downloads/macosx10411comboupdateppc.html
The combo update for Intel-based Macs...
http://www.apple.com/support/downloads/macosx10411comboupdateintel.html
Repair Permissions before & after re-install, then reboot again each time.
If all the above do not resolve the problem, then it's time for an Archive & Install, which gives you a new OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space...
http://docs.info.apple.com/article.html?artnum=107120
I only use Software Update to see what is needed, then get them for real via...
http://www.apple.com/support/downloads/
That way I can wait a week or so, check the forums for potential problems, and get Permissions & such in order before installing.

SunFire 480R - Solaris 10 New Install

Similar Messages

Maybe you are looking for