Sunfire X4150 fails to Boot after ILOM update to 3.0.3.30

After update from ELOM to ILOM and during update of ILOM from 2.0.2.6 to 3.0.3.30, system shutdown, and no boot anymore.
Turning on the system, later, I get the following erro, analysing the SP event log:
ID = 29 : 06/23/2009 : 15:46:11 : System Firmware Error : sensor number = 0x00 : BIOS corruption detected
The SP had gracefull update, but BIOS seems to be corrupted.
Any suggestions, please? How can I recover BIOS, or even, make the system work again?
Bruno Simioni

[SOLVED]
Downgrading the SP and consecutively the BIOS, server is online again.
Download SP and BIOS Firmware from Sun Fire X4150 & X4250 Software Supplemental 2.2.2, at Sunfire x4150 server downloads page, and, downgrade the 3.0.3.30 SP/BIOS to 2.2.2 version.
I really hope that an future version of 3.0 Tools and Drivers DVD makes Sunfire x4150 works fine.
Bruno.

Similar Messages

Dell Latitude E6520 fails to boot after Windows Updates

Hello,
I have a Dell Latitude E6520 that is not starting up after Windows updates. It installs updates and requests a reboot, after which it blue screens at the splash logo and reboots again. This goes on indefinitely. The only way to repair it is to boot from
a recovery disk and run:
dism /image:D:\ /cleanup-image /revertpendingactions
This is after running dism /image:D:\ /get-packages and noticing that several updates are still in an "Install_Pending" state. These are the kb's that are pending:
kb2982378
kb2978742
kb2977629
kb2976897
kb2973112
kb2972211
There were other updates, but those showed as installed. I would post the WindowsUpdate.Log, but I do not see a button to attach a file and the log is very long. Here is what I think is relevant towards the end of the log:
2014-09-18 10:52:04:214
496 540
AU Install complete for all calls, reboot needed
2014-09-18 10:52:04:216
496 540
AU Successfully wrote event for AU health state:0
2014-09-18 10:52:04:623
496 8a4
AU UpdateDownloadProperties: 0 download(s) are still in progress.
2014-09-18 10:52:04:623
496 8a4
AU Triggering Offline detection (non-interactive)
2014-09-18 10:52:04:623
496 8a4
AU AU setting pending client directive to 'Reboot Pending'
2014-09-18 10:52:04:623
496 8a4
AU Changing existing AU client directive from 'Progress Ux' to 'Reboot Pending', session id = 0x1
2014-09-18 10:52:04:625
496 8a4
AU Successfully wrote event for AU health state:0
2014-09-18 10:52:04:625
496 1668
AU #############
2014-09-18 10:52:04:625
496 1668
AU ## START ## AU: Search for updates
2014-09-18 10:52:04:625
496 1668
AU #########
2014-09-18 10:52:04:626
496 1668
AU <<## SUBMITTED ## AU: Search for updates [CallId = {7C1069F1-2D57-421E-A378-38DE401BF9F1}]
2014-09-18 10:52:04:626
496 166c
Agent *************
2014-09-18 10:52:04:626
496 166c
Agent ** START ** Agent: Finding updates [CallerId = AutomaticUpdates]
2014-09-18 10:52:04:626
496 166c
Agent *********
2014-09-18 10:52:04:626
496 166c
Agent * Online = No; Ignore download priority = No
2014-09-18 10:52:04:626
496 166c
Agent * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation' or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0
and DeploymentAction='Uninstallation' and RebootRequired=1"
2014-09-18 10:52:04:626
496 166c
Agent * ServiceID = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7} Managed
2014-09-18 10:52:04:626
496 166c
Agent * Search Scope = {Machine}
2014-09-18 10:52:05:210
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:07:170
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:09:475
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:09:569
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:11:590
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:14:999
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:16:887
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:18:753
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:19:623
496 1668
Misc WARNING: IsSessionNonstandardUI: session 65536 is an unknown session type 0; treating it as a standard session
2014-09-18 10:52:20:673
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:22:573
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:22:773
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:24:464
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:24:651
496 1668
AU AU received handle event
2014-09-18 10:52:26:366
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:27:520
496 1668
Shutdwn user declined update at shutdown
2014-09-18 10:52:27:520
496 1668
AU Successfully wrote event for AU health state:0
2014-09-18 10:52:27:520
496 1668
AU AU initiates service shutdown
2014-09-18 10:52:27:520
496 1668
AU ########### AU: Uninitializing Automatic Updates ###########
2014-09-18 10:52:28:206
496 166c
Agent * WARNING: Exit code = 0x8024000B
2014-09-18 10:52:28:206
496 166c
Agent *********
2014-09-18 10:52:28:206
496 166c
Agent ** END ** Agent: Finding updates [CallerId = AutomaticUpdates]
2014-09-18 10:52:28:206
496 166c
Agent *************
2014-09-18 10:52:28:206
496 166c
Agent WARNING: WU client failed Searching for update with error 0x8024000b
2014-09-18 10:52:28:253
496 1668
Report REPORT EVENT: {62FF14E3-DDBE-4DDC-BE90-12B98EC74605}
2014-09-18 10:52:04:216-0600 1
193 102
{00000000-0000-0000-0000-000000000000}
0 0 AutomaticUpdates
Success Content Install
Restart Required: To complete the installation of the following updates, the computer must be restarted. Until this computer has been restarted, Windows cannot search for or download new updates: - Security Update for Windows 7 for x64-based Systems
(KB2982378) - Security Update for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008 R2 SP1 for x64-based Systems (KB2973112) - Security Update for Windows 7 for x64-based Systems (KB2976897) - Security Update for Windows 7 for x64-based Systems
(KB2918614) - Cumulative Security Update for Internet Explorer 9 for Windows 7 for x64-based Systems (KB2977629) - Security Update for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008 R2 SP1 for x64-based Systems (KB2972211) - Security Update
for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008 R2 SP1 for x64-based Systems (KB2937610) - Security Update for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008 R2 SP1 for x64-based Systems (KB2894844) - Security Update
for Windows 7 for x64-based Systems (KB2978742)
2014-09-18 10:52:28:253
496 1668
Report CWERReporter finishing event handling. (00000000)
2014-09-18 10:52:28:253
496 1668
Report CWERReporter finishing event handling. (00000000)
2014-09-18 10:52:28:425
496 1668
Service *********
2014-09-18 10:52:28:425
496 1668
Service ** END ** Service: Service exit [Exit code = 0x240001]
2014-09-18 10:52:28:425
496 1668
Service *************
Please let me know if there is a better way of attaching the log to this post and thank you in advance for any help.

Hi ChristianBoman,
We could use the OneDrive to upload the log and then paste the shared link here. For more information, please refer to the following article.
http://windows.microsoft.com/en-us/onedrive/share-file-folder
for the update error 0x8024000b, please refer to the following article.
http://windows.microsoft.com/en-us/windows/windows-update-error-8024000b#1TC=windows-7
Please take the following steps:
1. Run the Windows Update Troubleshooter.
2. Click the Start button , type Run in the search box, and then, in the results list, click Run.
3. Copy the following text, and then paste it into the Run text box:
Cmd /c ren %systemroot%\System32\Spupdsvc.exe Spupdsvc.old
4. Click OK.
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

Acer aspire 5560g Failing to boot after Firmware update

Hey guys, So i recently upgraded my Aspire 5560g to Windows 8.1. I liked it but it seemed to have lost my drivers in the process (my track pad scrolling didnt work and my Dolby audio origram was gone). I went to for the drivers and decided to start with a firmware upgrade (9545 for hard disk performance). After the computer rebooted, I entered the dreaded Windows 8.1 boot loop. It would say "Your PC ran into problems..." with the bluescreen, then turn off. Then it would attempt the Automatic repair, and fail again, then restart the cycle. I wasn't able to even get into my BIOS until I cleared my CMOS, now at least I can get into BIOS. I created a bootable USB for Windows in hopes I could do a clean install, but even when trying to boot from a USB I get the blue Windows 8 screen, "Your PC ran into problems..."
Is there a way I can undo the firmware update, it seems like the culprit, doesn't it? Any help appreciated. Thanks EDIT: I've read that the Windows boot loop may be caused by outdated drivers. Think this could be the problem after I did the firmware update? How can I install the drivers without being able to boot into Windows? Thanks

Okay, I tried each stick at a time in both slots with the same results. Windows blue screened on both the HDD and the bootable USB. Isn't it too much of a coincidence that it started acting up after the firmware update?
To be clear, it was a firmware update for the BIOS. The page is here for the Aspire 5560G: http://us.acer.com/ac/en/US/content/drivers I am open to more suggestions, I'd really love to get this working again after dropping the $ on Windows 8

Kt4v , Barracuda failing Windows boot after bios update

Hello
I have KT4V , i had bios 6712 v1.7 installed. I bought today Sempron 3000+ and I wanted to make it works so first i downloaded Bios update "1c0"(latest one) version and flashed my bios . Everything went fine , i restarted PC , Bios asked me to for default settings i pushed F1 , and everything was going fine (still with old CPU Athlon 2000+) , Windows started to boot , and after 2 sec of Windows getting load(Screen with blue load bar appeared for 1-2 second) RESTART , i was confused .
I installed 1.7 Bios(my old one) and still the same. Trying to find out what hapenned i unpluged my Secondary Disk (Primary SLAVE - Barracuda 120GB 7200.7) , and everything was working , windows loaded from my Primary master like always .
Everytime i plug in the Barracuda windows is restaring during boot.
What is going on ? PLZ HELP , Try to imagine how mad i`am with new CPU at my desk :((((
P.S.I made all combinations with Slave , MAster , another data cables , another supply cables . Still nothing

Quote
boot from your windows CD, and attempt a repair install of windows. clearing CMOS / updating BIOS has probably changed some settings that windows disagrees with
Repairing a Windows installation
done . Result - none , still restarting when loading the windows with Secondary Disk.
Quote
I'm not sure, have you cleared CMOS? Power off, unplug power cable, wait a minute or three, move jumper, move jumper back, power cable in and power on. And don't forget to set time and date.
done , result - none , i changed jumper settings and have been waiting for 2 minutes.
Quote
KT4V supports 333 FSB, so why did you have to upgrade Bios ? As Fred says, after each change in Bios ( upwards/downwards) you should clear CMOS.
Kt4v support FSB 333 , but it dont support all CPU , thats why there is a latest patch Quote
-Fix system reports incorrect message for AMD 3200+ CPU.
-Support Sempron L2 512K 3000+ CPU.
And I`am still with Athlon 2000+ , because my disk dont go with windows.
I unnistalles Alcohol 120% , i thought that it could be letters of drive conflict , but no :(
Bios detect harddisk perfectly .
Have no more ideas what to do :(

Leopard USB install no longer boots after software update

Hi all,
I have recently installed Leopard onto a USB partition in order to perform maintenance on my main Leopard installation. Installation proceeds without a problem however after downloading software updates the USB partition will not boot successfully, despite there being no problems with the disk / volume structures / apparently anything at all. In desperation I also tried to install Tiger, which worked, however I have the same problem after updating - it will not boot! I don't think my hardware is at fault - Techtool Pro tells me all is in order.
Has anyone had this problem and if so, how did you fix it?
Thanks,
Jason

I just installed Leopard onto a USB 2.0 external hard drive for a dual-boot. It booted fine at 10.5.1 but is taking ridiculously long to boot after 10.5.2 (I just got it to finally boot after the update while waiting more than 40 minutes!).
It seems that you may want to attempt booting several times - maybe turning off the machine in between or booting to the internal OS first and then to the external. Can't help you much beyond that as this is my introductory experience with this mess.

Macbook pro won't boot after installing update 10.9.3

macbook pro won't boot after installing update 10.9.3

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

My keyboard failed to function after software updates

what should i do..my keyboard failed to function after software updates. i'm using virtual keyboard now.

It would help us to know which comp model you have, which OS & version you're using, how much RAM, etc. You can have this info displayed on the bottom of every post by completing your system profile and filling in the information asked for.
This will help in providing you with the proper and/or correct solutions.

Wont boot after windows update

M y Sateite A305 s6916 wont boot after windows updates tried to install.

Satellite A305-S6916
tried .. every option on F8
Try this. Download a repair disc from here.
   Windows Vista Recovery Environment ISO X64 version (64 bit)
If you can reach the Recovery Environment by booting that, try the Startup Repair and let us know what happens. Sometimes you need to run it more than once.
   Startup Repair: frequently asked questions
Also try a System Restore.
   What are the system recovery options in Windows Vista?
-Jerry

Restored 10.6 OS from CD and fails to Boot after Combo upgrade

I have a clean install of Lion on my internal drive and an external clone of the HD from the previous Snow Leopard install. The Clone worked until I updated via the latest auto update. I have App's and other settings to transfer to Lion from this clone so want to get it working so I can ensure all the App's are upgraded to work on Lion or are deleted.
After the external drive failed to boot I reinstalled the system from my Snow Leopard Install CD, not the 24-inch iMac (Mid 2007) restore CD.
I then used Auto updater to install the combo and other updates to 10.6.8 this booted fine until I upgraded Safari 5.1 and Java - the last items that came up on the software updater. Upon restart, the boot failed in the last portion of the boot and at this point the Apple emblem went away and the round circle with diaginoal line apeared.
On starting with the option key down, the clone disk 10.6.8 shows as being available, along with the internal Drive, for booting.
Starting with "command + S" gets through to the last line of the process then states "waiting on Root"
When compaired to a Snow OS that boots OK it is the last line of code before the curser is ready for entering a command.
Can anyone tell me what to look for or how to repair this error so that I can get my data across to Lion. Thanks

Well, in case anyone else has a similar problem I managed to fix the system by the following process:
I reinstalled 10.6.0 from the retail Snow Leopard CD. The drive Booted OK but I needed to be upgraded to 10.6.8 to use the migration tool so I then upgraded using the Software Update utility. Boot failed again at this point and could not be fixed by anything I did.
I then reinstalled 10.6.0 from the CD to try again, but the HD would not boot this time around.
I downloaded CleanApp by Synium Software (http://www.syniumsoftware.com/cleanapp/) on a commendation from the famous eBook, "Take Control of installing Lion" by Joe Kissell of TidBits. I used this from my Lion HD to remove all orphan files, PPC files and Apps, and other junk. Snow Leapard still not Booting after repairs by various disk repair utilities including Apples.
I Booted from my internal HD using Lion and ran SuperDuper to make a new Clone of the failed HD on a second external HD. Took a day and a night to run while I was at work, but the new clone would not boot at this stage so I ran SuperDuper again using the "Smart Update Backup" option. This just adds changed files or missing files to the clone. At the end of this process I had a running Clone that would boot on 10.6.0.
I Booted from the second Clone and used the Software Update utility then to up grade in the two stages the Auto system used to bring my OS up to 10.6.8. This was successful and I had a Bootable Snow Leopard with no old Apps from which to Migrate my data.

Mac Mini will not boot after Security Update 2008-007

Hello,
A G4 Mac Mini machine I was asked to take a look at will not boot after the owner (succesfully) installed Security Update 2008-007 from Software Update. Booting always hangs at the blue screen after the Apple logo, and booting in verbose mode reveals that WindowServer is crashing repeatedly. Permissions and filesystems have been repaired, PRAM reset, etc. Safe boot also exhibits the same problem, but it is possible to boot to single user mode. Hardware checks out fine with diagnostic utilities.
Any suggestions on how to fix this? Unfortunately, backups are not available (it's not my machine =).

Hi Arkku , and a warm welcome to the forums!
I'd certainly give Sig's advice a try first.
If that should fail...
applesetupdone...
This was Posted by: JoseAranda at September 9, 2006 3:48 AM
"OK, restart your computer, hold down Command-s and type in the following:
/sbin/fsck -fy Enter
/sbin/mount -uaw Enter
rm /var/db/.applesetupdone Enter
# The rm command is the remove command which deletes the file.
# Robert: I'd rename the file via: mv /var/db/.applesetupdone /var/db/.applesetupdone.old
reboot Enter
Once you've done that the computer reboots and it's like the first time you used the machine. Your old accounts are all safe. From there you just change all other account passwords in the account preferences!!
end of posted by: JoseAranda"
Reset OS X Password Without an OS X CD...
http://theappleblog.com/2008/06/22/reset-os-x-password-without-an-os-x-cd/

HP Pavilion 15-n268sa will not boot after windows update (windows 8.1)

After a series of windows update (windows 8.1) my HP Pavilion 15-n268sa will not boot up, no fan noises, no lights no nothing.
I have tried a "hard reset" a number of times with no success.
When the battery is present the white LED flashes 3 times when the power button is pressed.
Please please help.

Hello Cuffy,
Welcome to the HP Forums!
I understand you notebook will not boot after a series of Windows updates.
Can you tell me if you are able to access the HP Recovery Manager by repeatedly tapping the F11 key while the notebook turns on? If you can access this, try doing a system restore to before you installed the updates. If not I would suggest you go through this document: Computer Does Not Start and the LEDs Blink or the Computer Beeps.
If it's the Caps Lock light that is blinking this document will tell you exactly what the error is (spoiler: 3 beeps is a memory failure). This could also explain the failed updates. The updates are stored in the RAM before being applied to the operating system.
You can try reseating the RAM, or using only 1 of the RAM cards, as you have 2x4GB cards. If it still doesn't work with 1 card, try the other card to confirm it has failed.
You can replace defective cards via HP Phone Support if covered under warranty or at the HP Part Store if not covered. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
Hopefully this information helps!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

Mac fails to reeboot after Safari update install -How to recover

I installed an update for Safari following which My Mac fails to reboot.
I am running the latest version of Lion on a mini, Intel dual core 2.0GHz 4 GB RAM.
ALl I get is the grey screen with an Apple logo and a spinning wheel.
How should I recover fro this?

[SOLVED]
Downgrading the SP and consecutively the BIOS, server is online again.
Download SP and BIOS Firmware from Sun Fire X4150 & X4250 Software Supplemental 2.2.2, at Sunfire x4150 server downloads page, and, downgrade the 3.0.3.30 SP/BIOS to 2.2.2 version.
I really hope that an future version of 3.0 Tools and Drivers DVD makes Sunfire x4150 works fine.
Bruno.

T540p wont boot after bios update

I updated my T540p a few days ago using Lenovo Solution centre, hiwever, it cant boot after update. The power button is on and fan spins, but the screen is black. I tried: remove battery and all external device and press power button for 30 seconds, out back the battery, still screen wont show anything; tried usb recovery stick, didn't work; tried Recovery discs from Lenovo, still failed.
Please help. Thanks in advance.

Ouch. And just out of luck.
Chances are, the board is bricked.

Can't boot after installing updates

I am quite new apple and this is my first problem I have encountered.
I downloaded updates and now my computer wont boot. I have tried safeboot and it just freezes on the 'starting OSX bar'. I have inserted 'install disk 1' (which is OSX 10.4.6) and gone through disk utilities to repair permissions and the disk - then starting from the hard drive in safeboot and it still gets no further than the 'starting OSX bar'.
If I chosse to boot from the install disk will it take me to the 'erase and intall' option.
What should I do? If anyone can help I would be very grateful.
Thankyou

I guess you could skip the steps you have done already...
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
The usual reason why updates fail or mess things up, is if Permissions are not fixed before & after every update, with a reboot... you may get a partial update when the installer finds it doesn't have Permissions to change one obscure little part of the OS, leaving you with a mix of OS versions.
Some people get away without Repairing Permissions for years, some for only days.
If Permissions are wrong before applying an update, you could get mixed OS versions, if Directory is the slightest messed up, who knows!
If many Permission are repaired, or any Directory errors are found, you may need to re-apply some the latest/biggest updates.
May even need to do an Archive and Install if you have room on the HD...
http://docs.info.apple.com/article.html?artnum=107120

MacBook won't boot after installing update 10.9.2

Hi there,
After successfully installing the 10.9.2 update on my MacBook Pro, I was able to boot to the updated system once. Then, suddently my macBook crashed and I was unable to boot again.
I managed to find a way to backup my files using the recovery mode and the Disk utility, however this wasn't straightforward to me since I was using FileVault..
Does anybody else have a similar experience with the 10.9.2 update?

The login screen appears as usual, and I am able to put username/password. Then, it fails to login and it returns the user to the login screen without mouse or keyboard working.
I booted using Command Button + S (single-user mode) and I see the error
"error loading mach kernel 0xe"
At least, I am able to boot in recovery mode to backup my disk :-)

Sunfire X4150 fails to Boot after ILOM update to 3.0.3.30

Similar Messages

Maybe you are looking for