SunRay 2FS DTUs dead after Firmware upgrade?

Hi everyone,
although I am fairly experienced in Solaris this whole Thin Client business is a bit of unchartered territory to me as of yet... following situation:
I got 2 SunRay 2FS DTUs and I have a vanilla PC setup with Solaris 10 U6 for x86. Installation was smooth except for the onboard NICs - I had to locate and manually install the appropriate drivers (skge). Installed SRSS 4.1, no problems, made a basic configuration (skge0: standard LAN, skge1: SunRay LAN with the standard 192.168.128.0/24 network). Installation told me DTUs would be firmware-upgraded after next power-cycle. Fired up the first DTU, it displayed the firmware upgrade OSDs and power-cycled - so far so good. But after the power cycle nothing happened - LED on the front is green so obviously POST is okay but the OSD constantly display status "1" (waiting for ethernet link to come up) and nothing else happens. Link lights on the NIC are on, when I send packets on the skge1 network (pings) they even flash, so I assume it's not the cables. Strangest things of all: I tried DTU 2 and the exact same sequence happened - so I am sitting here with 2 dead DTUs - any chance of reviving them? I scoured the 'net for information but I got no description that was even close to my problem...
Kind regards from Germany,
Henning

after installing sun ray server remember to:
1) utadm
2) utconfig
http://docs.sun.com/source/819-2383/config.html#59570 <- old but right

Similar Messages

Thunderbolt Display "dead" after firmware upgrade to Version 1.2

Hi,
I just run the Thunderbolt F/W update to 1.2 as offered by the AppStore Update. I have a 2014 MacPro with 2 Displays connected. In good faith I just confirmed to apply the update without much reading the fine print. The F/W update brought the system to a complete standstill. After 2 hours of waiting in the boot screen, I rebooted the system manually (5 secs power button). One of the Thunderbolt displays first just flickered, then decided to completely die. The System report says: unknown device in the Thunderbolt section. The 2nd display hasn't been updated during this procedure.
How can the F/W of the 'dead' display be re-installed? I also tried to connect it to a MacBook pro. Same result. The display is entirely black.
Any help or suggestion is much appreciated. Thanks!

Put me on the list as well.
I've had this TB display for two years and have had no issue with it. Clicked OK on the firmware prompt and now I have a $1000 paperweight/laptop charger.
What I have tried:
Reset SMC and NVRAM on my MBP.
Unplugged the display from power and all peripherals and let it sit for ~24 hours before trying again.
Downloaded the firmware installer from Thunderbolt Display Firmware Update v1.2. It tells me that no thunderbolt display is connected.
So far nothing has produced a result.
System report shows an unknown device on the TB port.
A used logic board for the display is around USD$220 on ebay.
I really wish I had not attempted to install the firmware now.

PC-Suite sync fails after Firmware upgrade of E65

After firmware upgrade of E65 PC-Suite stops syncing Calendar & Contacts from outlook. No error messages, just "0 entries has been updated".
- PC-Suite updated to 7.0.9.2
- Outlook 2003
- XP Prof.
Any ideas?
Solved!
Go to Solution.

The funny thing is - the notes are synced???? If I restore some old contacts they'll double up in outlook, so I think the problem is, that the sync app doesn't see the outlook contact & calendar folder.
Does somebody has an idea?

Crippled 192.168.1.1 page after firmware upgrade

hi,
i recently upgraded the firmware of my WRT160N V2 to 2.0.03.
but since then when i login i get a crippled page on 192.168.1.1 with not even a menu. so i cant even downgrade. is there something i can do?

It is good to know that the issue is resolved
After firmware upgrade it is always recommended to reset and reconfigure the router and I think that is why you were unable to see the menu on the setup page of your router.

T410i SSD user and master password problem after firmware upgrade

Hello.
I have problem with my Corsair Force 3 120GB SSD. After firmware upgrade of SSD my master and user HDD passwords are no longer valid. I'm stuck on BIOS screen and cannot unlock my SSD. After firmware upgrade procedure i got BSOD. Same happened during firmware upgrade on my previous SSD (INTEL X25-M 80GB) but after restart everything was OK. Please help!
Previous firmware version: 1.3
Current firmware version: 1.3.3
SSD connected to another computer shows RAW partition data, but firmware version is 1.3.3 - seems like update was successful.

My X301 Intel x18 got bricked also after a BIOS update then secure erase (was going to sell it). I plugged it to a USB kit and onto a desktop and it was recognised and able to format. But plugging it back to the lenovo it is still a brick. My lucky star there was warranty it was replaced by lenovo.
You may want to try it and extract the data, if it works. And hopefully you can still format it and made it work pluggin back to the lenovo.

SB wow wireless not working after firmware upgrade

Hello,
In the beginning of this year I bougth a pair of Sound Blaster World of warcraft wireless headset. And there have been alot of trouble with them, I've been using the latest software but not the latest firmware ever since then.
And every now and then my mic stop to work, I could hear sound but the mic was totally dead, and all of a sudden, of no logical reason the mic started to work agian.
So I thought a firmware upgrade could make them work better, but no, i upgrade firmware from .9.x to .0.x.
And guess what happens? Nothing works no, not the sound, not the mic, the USB trasmitter cant even sync with the headset anymore.
Ive tried a million things now, some of them are:
. Just tried to reinstall it, didnt work
2. Tried to install it in winxpsp3 compability mode, didnt work.
3. Tried to clear all temp-folder (the temp-folder under c:\windows\temp and the user-temp) after Ive uninstalled it, didnt work.
Im running on Windows 7 Professional x64 edition.
What could cause this? I havnt tried to install them on a XP-computer yet tho. But I have to get them work in Win7, since i cant downgrade just because of a headset, huh?
Thanks,
Johan

Ok, please redirect me to a tecnical supportpage where I can find potential solutions,
- and instructions how I do for example a downgrade of firmware?
PS, This page does not include any potential solution:
http://support.creative.com/Products...tDetails.aspx?
catID=437&CatName=Headphones+%26+Headsets&subCatID =23&subCatName=MIDI+Keyboards&prodID=9068&prodName =Sound+Blaster+World+of+Warcraft+Wireless+Headset& bTopTwenty=&VARSET=prodfaqRODFAQ_9068,VARSET=CategoryID:437

No power after firmware upgrade on nomad jukebox zen xtra

I have the nomad jukebox zen xtra 30gig that froze up over a year ago after i tried to install the firmware upgrade. After the unsuccessful attempt, the mp3 player stopped working.... I mean no power at all. I've changed the battery and recharged the battery from an outside source...still no luck. I can't even try any of the suggestions anyone gives on this site because I have no power.Does anyone have this problem? More important, does anyone have this problem and know of a solution?I've already set my pc back to wmp 0, I have the firmware on the desktop waiting. Now all I need is some power on this unit so that i can try some of the suggestions that seems to be working for people. Thank you

I have the same problem too, but my unit is a?Creative Normad Junebox Zen Xtra 40GB. I was trying to find a solution to my problem when I read about your problem. I have pressed the reset button, on / off switch, removed the battery, reinstalled the battery, and nothing seems to work. I was hoping you?might get a solution to this problem, so that I might be able to fix my MP3 player. If I hear of a solution, I will let you know, thanks for sharing. Issue:? While updating the firmware to the Zen Xtra 40 GB, the unit powered down and?has never came on again. There seems to be no real reason why the unit should not power up. The battery and the AC adapter are working correctly. I am very disappointed in Creative...

No contacs after firmware upgrade on N70

Hi
I did a firmware upgrade yesterday on my N70 using NSU. Of course I did a backup using the uptodate Nokia PC suite. After the firmware upgrade I saved the data back to the phone aagin using the Nokia PC suite. Everything looks good except that no contacts are there.
I did the upgrade again just to make sure that everything went OK with the same result.
Can some help or has the same problem?
Firmware V 5.0638.3.0.1 18-09-06 RM-84
PC Windows XP SP2
Nokia PC Suite 6.82.22.0
NSU 1.2.0en
Best regards
Chris

not sure about your PC Suite version but this has been well documented in these forums and I had the same problem and with N70. I think it was mentioned as a PC Suite issue, or a combined PC Suite issue N70 issue with many people reporting it. Anyway nothing you can do but enter your contacts or transfer from another phone

HP Laserjet p1102w - after firmware upgrade / Smart Install update - down to 1MB free memory

Hello,
I have a Laserjet p1102w running off a laptop with Windows 7 64-bit. Just bought the printer this month.
After updating the firmware to 20120814 version and updating the SmartInstall update utility for the 20120814 version as well, I am now down to 1 MB free memory (out of 8MB originally). [Another LJ p1102w updated prior to these updates has 3MB free memory.]
Because I have 1MB free memory, the printer is almost a brick. It can print simple text based pages - however, printing any page with a graphic or a PDF file will cause the printer to take forever to receive data - essentially preventing printing a page on my new printer (while printing the same page instantaneously on my older nonupdated p1102w).
Is there any way to fix this problem, given there is no memory upgrade option? Otherwise, this printer is a brick.
Thank you in advance for a reply - especially from HP.

Hi cyskim,
Did you tried turning the printer off and on after updating the firmware? This should clear its memory, including any memory may affected during the firmware upgrade proccess .
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

HP 5524 Wireless does not work after firmware upgrade

HI,
I have just purchased an HP5524. After initial problems setting up the WPA key from the printer screen, I connected via USB, found the printer and swapped to wireless successfuly. I then installed the printer software on all my computers at home successfully over wireless.
The printer then needed a firmware upgrade to support eprint (?), which is successfully connected, downloaded the fireware, installed and went through the boot cycles successfully.
However, ever since wireless will not work. Before I return it to the retailer as "not fit for purpose" I thought I would ask the forum. The diagnostics downloaded a tool, which I went through, but this did not offer solutions that I had not already tried.
Thank you

Hi,
Thank you for posting you query,
In order to resolve the issue, please make sure the printer is placed closer to the router and uninstall the printer drivers already installed and then start the instalaltion and seelct teh connection type as wireless network. Then select use USB to configure wireless and when prompted conenct the USB cable and then select the network and enter the encryption key follow the onscreen instructions.
If the issue still persisits, please open the browser and in the address bar enter the IP address of the router and click on GO. This will take you to the router configuration page. On the router page, please click on Wireless Setup and please make sure SSID Broadcast is enabeld and the Wireless Mode is set to Mixed or 802.11 B/G/N and the Wireless Channel is set to 11 and click on Apply. Then try to connect the printer to the network by using the CD.
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"
(Although I am employed by HP, I am speaking for myself and not for HP)

Fans And Voume after FirmWare Upgrade

Hey there!
I have two very positive pieces of information, some repeated:
1) The volume of my speakers and "line out" was weak at best prior to the FirmWare upgrade. Now, it is positively explosive! I mean, the volume control works just like I would have expected. Perfect...
2) The fans are coming on more consitantly. I can actually hear them now, which makes me wonder... The temp on the Hard Drive has not gone above 92 since I upgrade the firmware (not that I have noticed however).
Bob

Hi Bob!
What did you use to check the temperature?
I installed the 10.4.6 and the firmware, and now I could cook an egg on the keyboard. I didn't have the heat problem before, now after the updates, I am fried (literally).
Gus

Iomega Storcenter ix4-300d stuck at 95% after firmware upgrade

Hi,
I upgraded my device after I got an email that there is a new firmware:
An update to version 3.2.10.30101 of the Iomega StorCenter ix4-200d software is now available
I installed the update but now it is stuck at 95% after rebooting.
Never had any problem before the firmware upgrade.
Any advice?

Hello BelgianTomas
I recommend that you first power down the unit if the unit has not completed the boot process. Then re-seat all disks and try booting the unit again. Please do not try to access the web interface until the power led is solid white.
Next would be to try moving the internal disks to different bays to see if a different drive order wil allow the unit to boot.
If that does not help, LenovoEMC suppor should be contacted for more advanced options.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Content Copier wont restore after firmware upgrade

I upgraded my N95 8GB to the latest firmware this morning (30.0.018), took 2 complete backups using Contect Copier V4 prior to doing so, but after the upgrade every attempt to restore contacts, settings, etc has failed.
I've tried doing the recommended re-formatting procedure, followed by a restore, which did not help. I've tried restoring individual items only, instead of the whole lot, which also didn't work.
According to the log at the end of the restore, the restore completed successfully. Reality suggests otherwise though.
Could anyone please help?
Thanks,
Adriaan

Right, I've tried using OVI, which did NOT resolve the problem. In fact, it gave identical results to the content copier included with the nseries suite.
I've written to Nokia support who have replied as follows:
"In this instance, allow me to suggest a few workarounds in order to rectify the issue on hand.
First, I suggest that you delete any data not needed from your Nokia N95 8GB to free up the internal memory of your phone before restoring the backed up file. I would like to also suggest that you select the content files that you want to restore to the Nokia N95 8GB. Once you have connected your Nokia N95 8GB to the PC and launched the "Content Copier" application, please select the content file types that you want restored on the phone.
However, if you are still unable to restore the backed up file to your Nokia N95 8GB, there may be inherent issues with your Nokia N95 8GB that may prevent you doing so. In this case, please take your phone to your nearest Nokia Care Point for an assessment. The Nokia Care Point will assess if a repair is required and advise if this may be covered under warranty."
So it looks as if I'm going to have to take it in for repair...

N97 cannot use as modem after firmware upgrade

Hi, sorry if this is a repeat post but driven to distraction.
I use my N97 as a modem to connect to the internet from my laptop when I'm away from home. Since upgrading the firmware I cannot connect through 1 touch access or direct through dial up.
When attempting to connect through 1 touch I get as far as connecting device and then I get the message "Failed to connect device".
I have removed the modem through internet properties and reinstalled PC Suite (after using PC suite cleaner). I am running windows 7 but was connecting through 7 before the firmware upgrade.
Now I'm at a loss. Anyone got any ideas?

Saw another post here that said they make a completely new network with a different name and it worked. I decided to give it a try and it actually did work!!! Don't have any clue why but I don't really care since my network is running again.

BEFW11S4 constant disconnect after firmware upgrade

I was having trouble with my router losing connection every 2 hours or so . I have downloaded and installed the latest firmware and now it keeps disconnecting almost every 30 min. I have a static IP on my main pc and dhcp enabled for my xbox360. I have checked the cables if they were bad by swapping them but the problem was still there. Any help would be very much appreciated.

After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.
Also, please list all the static LAN IP addresses that you are using on your network.
If you are not using the default DHCP server range of 192.168.1.100 thru 192.168.1.149 , then please state your DHCP server range.
Are you running any peer-to-peer (P2P) software? If so, this is a known cause for router slow downs and disconnections. Temporarily stop using the P2P software, then reboot router, and see if this corrects your problem.
Who is your ISP? Are you on a cable system? Some cable systems monitor the MAC address of the devices connected to them, and eventually boot off any MAC address they don't recognize. If you are on a cable modem, try cloning your MAC address (done in the router), and see if this corrects the problem.

SunRay 2FS DTUs dead after Firmware upgrade?

Similar Messages

Maybe you are looking for