Sup V with 4507R status led in Red

Hi,
I carried out an upgrade in 4507R with 2 sup V, I loaded in both card 12.2(53)SG10 and I confirmed the redundancy is working
I don't understand why both status led (for Sup V) are in red.
the loggs do not show error ,  any idea how can I identify the reason of red color in status led?
regards
Mod  Redundancy role     Operating mode      Redundancy status
----+-------------------+-------------------+----------------------------------
1   Standby Supervisor  SSO                 Standby hot
2   Active Supervisor   SSO                 Active
redundancy
mode sso
main-cpu
  auto-sync standard

Hello,
The status LED can actually lend useful information regarding the potential culprits to your issue. You can check out the STATUS LED Error Indications in the 1601 User Manual.
In this case, it looks like you should contact National Instruments directly since it seems as though the module did not power on correctly. You may have to return your unit for replacement or repair.
Cheers,
Emilie K. | Applications Engineer | National Instruments

Similar Messages

  • IPS status LED stays red

    Dear Friends,
    There is a IPS 4260 that reports the status LED to red. When reading the hardware installation guide, i came to know that this indicates a POST failure. I forced a POST again of the IPS by rebooting the IPS but i could not capture any significant error.
    However, i am enclosing the captures of the boot process (Filename: IPS) and the sh tech-support (Filename: IPS Tech support).
    Can you please help me on this?
    Thanks a lot
    Regards
    Gautam

    Shutdonw the IPS for 5 - 10 Minutes and the Restart i did and the issue has been resolved .
    Thanks,
    Mustafa 

  • FP 1601 status led shows red continuously

    I am trying to use FP 1601 which was already configured long before. But now the status LED is continuously red .Power LEd is green and all other LEds are off. Am giving 24V power and checked that it is given to V and C properly .Ethernet connection is also proper. i tried to reset , but could not. i cant use it in anymore. can anyone help in troubleshooting

    Hello,
    The status LED can actually lend useful information regarding the potential culprits to your issue. You can check out the STATUS LED Error Indications in the 1601 User Manual.
    In this case, it looks like you should contact National Instruments directly since it seems as though the module did not power on correctly. You may have to return your unit for replacement or repair.
    Cheers,
    Emilie K. | Applications Engineer | National Instruments

  • Blackberry Pearl 8100 randomly shuts off and the status LED flashes red

    My pearl was reciently unlocked and changed from AT&T service to t-mobile. after this switch the pearl started having fits of rage where it will turn off randomly, weather any keys have been hit or even if it is idle. the device LED then flashes red, sometimes once, other times it will flash once every 4 seconds for hours. then it will randomly turn back on either to the exact screen it had been on before it powered off or it will reboot completley and start the normal start-up procedure and varify security checks just as if the battery were removed. i tried removing the batery and leaving the phone disassymbled for a few nights but in the morning the plague is back and unrelenting. sometimes all i have to do it pick the device up and it will shut off. other times i will be plugging away with it for 20 or so minutes on the internet and then it will die suddenly. it also cuts out in the middle of phone calls. if anyone can help,please let me know.
    blackberry 8100 v4.2.1.96

    Is it a new phone? If it's less then a month old see if you can return it, otherwise you can try reloading the OS.
    So if you're willing to try that, do the following.
    First download and install the Desktop Manager from here (4.6 without Media Manager is recommended): https://www.blackberry.com/Downloads/entry.do?code=A8BAA56554F96369AB93E4F3BB068C22
    Next you can use the Backup and Restore feature present in the software to make a backup of all the data on your phone.
    Next download and install the handheld software from here: http://na.blackberry.com/eng/support/downloads/download_sites.jsp
    Afterwards try reloading the OS by connecting the device to your computer, open the Desktop Manager, then go into the Application Loader. This will open a wizard that steps you through reloading the OS onto your device. More detailed steps can be found here:
    http://www.blackberry.com/btsc/KB03485
    If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
    Remember to resolve your thread by clicking Accepted Solution.

  • CFP status led - stays lit solid red!

    Hi,
    I have a problem with a cFP-2120 RT controller where the red LED status light stays lit.  On the instruction manual it says that the unit was not powered up correctly and to contact NI.  The controller used to work fine until we had a short on the mains side of the power supply The AI, AO and thermocouple modules did not power up but the DI and DO modules seemed to be getting power.  Is there anything we can do or just send it back for repairs.  When I replaced the controller with another one, the system worked fine and the status LED turned off after a few seconds.
    rgds
    Inzaghi_2

    Sounds like you've proven that the controller is bad.  Next step is an RMA from NI.  Make sure NI tells you what failed in the controller and see if they will comment on what might have caused it.   The idea being to see if you can do anything to prevent this failure in the future.

  • MDS 9216 - showing red status LED, not starting up

    Hi,
    In a recent power loss (took out our R&D UPS in the process), an MDS 9216 we have in R&D failed.
    On power up, it shows a red status LED, and does nothing. We've pulled and swapped PSUs (something we're told is a common fix for a common problem with these chassis), to no avail.
    Strangely, we pulled the fan card (which had a green light), and put it back in to see it now also has a red status light.
    We've swapped all cards around for new and spares (even the main cards) and they show up with red status lights in the chassis (can't test them in another chassis at present) so I assume this problem is with the chassis itself (ie the backplane or PSUs).
    Any ideas, any similar experiences?
    Many thanks,

    As far as warranty, it would be covered for 1 year or 90 days from purchase....not sure which, but since the 9216 is end of sale for a few years now, I doubt that is covered under warranty. If you have a maintenance contract covering that 9216 serial number, then it would be covered. The design on the 9216 is that the module 1 is not field replaceable. There is no Cisco part number for the slot1 line card. It is a hybrid of a 16 port FC module with a supervisor daughter card. It is basically considered part of the chassis. If you have your own spare 9216 and feel energetic you could replace the slot 1 line card....but from the official support perspective, it is not replaceable.
    There are no other replaceable parts besides the chassis and PS that would cause this problem. (I assume you have removed any line card from slot2 to be sure it was not causing the problem).
    Thanks,
    Mike

  • CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red, what is this? it isn't in the manual

    CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red in a pattern, red off then red red, Our AP isn't working it won't show up on our Cisco WLC 2125 anymore and this is the LED indicators, I've checked in the manual and this combination of LEDs do not exists??

    No cisco web is working perfectly.
    do you have a valid CCO id with smarnet contract ?? then only you can download new IOS for AP:
    Autonomous AP image:
    http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=284180979&release=12.4.25d-JA2&relind=AVAILABLE&rellifecycle=ED&reltype=latest
    LAP AP image:
    http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=280775090&release=12.4.25e-JAP&relind=AVAILABLE&rellifecycle=ED&reltype=latest
    Regards

  • Problem Cisco AIR-LAP1131AG-E-K9 Ethernet LED = Off; Radio LED = RED ; Status LED = RED ;

    hi,
    I have a Cisco AIR-LAP1131AG-E-K9 when I boot one accesspoint it gives  Ethernet LED = Off; Radio LED = RED ; Status LED = RED  and only next listing in the screen:
    Xmodem file system is available.
    Flashfs[0]: unable to allocate available block.
    The system has been interrupted, or encountered an error during initializion of the flash filesystem.
    The foolowing commands will initialize the flash filesystem, and finish loading the operating system software:
    flash_init
    ether_init
    tftp_init
    boot
    When I type this commands, it doesn't help at all. The output will be following:
    ap: flash_init
    Initializing Flash...
    flashfs[0]: out of memory
    ...done Initializing Flash.
    ap: ether_init
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    ap: tftp_init
    Unable to get our ip address: no "IP_ADDR" variable set
    ap: boot
    Loading ""...; permission denied
    Error loading ""
    Interrupt within 5 seconds to abort boot process.
    Boot process failed...
    ap:
    what i do ?  please help , thanks

    Duplicate posts.  
    Go here:  http://supportforums.cisco.com/discussion/12154826/problem-cisco-air-lap1131ag-e-k9-ethernet-led-radio-led-red-status-led-red

  • I cannot import my AVCHD files by using log and transfer. I can see all the files, but when I add the file to import que it doesnt work, the status is a red (!) and says that its no data. I have tried with different cards and different cardreaders, but it

    I cannot import my AVCHD files by using log and transfer. I can see all the files, but when I add the file to import que it doesnt work, the status is a red and says that its no data. I have tried with different cards and different cardreaders, but it is still the same. Why?!

    Please give us more specific information -
    What make/model camcorder are you using?
    Are you absolutely certain this is AVCHD video?  Tell us more about the video settings you used in the camcorder (eg, frame size, frame rate, quality level)
    Why are you attempting Log & Transfer from a card reader instead of from your camcorder?  Have you tried doing Log & Transfer from your camcorder?
    Are the SD cards straight from the camcorder, unaltered, or are you just using the cards as storage?
    Are you using FCE 4.0 or FCE 4.0.1?

  • SUPERVISOR WS-X45-SUP7-E REDUNDANCY, STATUS LED ORANGE?!?

    hi all,
    i have a 4510R+E with 2 SUPERVISOR WS-X45-SUP7-E configured in redundancy mode.
    The status leds of 2 supervisor is orange and don't become green!!
    Can you help me?
    Below you can see the redundancy configuration:
    redundancy
     mode sso
     main-cpu
      auto-sync startup-config
    Thanks to all!!!
    Alberto.

    You can see the show module:
    FERCAM_4510#sh module
    Chassis Type : WS-C4510R+E
    Power consumed by backplane : 40 Watts
    Mod Ports Card Type                              Model              Serial No.
    ---+-----+--------------------------------------+------------------+-----------
     2    48  10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1908L9HK
     3    48  10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1903L5R5
     4    48  10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1906L6Z7
     5     4  Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1910L326
     6     4  Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1910L2SX
     M MAC addresses                    Hw  Fw           Sw               Status
    --+--------------------------------+---+------------+----------------+---------
     2 84b8.024b.8a10 to 84b8.024b.8a3f 1.1                               Ok      
     3 84b8.024b.8e30 to 84b8.024b.8e5f 1.1                               Ok      
     4 84b8.024b.8a40 to 84b8.024b.8a6f 1.1                               Ok      
     5 74a2.e680.2dc0 to 74a2.e680.2dc3 3.0 15.0(1r)SG5  03.07.00.E       Ok      
     6 74a2.e680.2dc4 to 74a2.e680.2dc7 3.0 15.0(1r)SG5  03.07.00.E       Ok      
    Mod  Redundancy role     Operating mode      Redundancy status
    ----+-------------------+-------------------+----------------------------------
     5   Active Supervisor   SSO                 Active                           
     6   Standby Supervisor  SSO                 Standby hot                      
    System Failures:
    Power Supply:   bad/off (see 'show power')

  • Cisco 1131AG LWAP status led yellow and other leds blinking green

    I have a problem with three AIR-LAP1131AG-E-K9  that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.
    The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).
    The SSID broadcast is enabled.
    On the switch the interface is up and there is traffic going in and out of the LAP.
    I tired power reset and factory reset for the APs but the problem remains the same.
    Any ideas for what might be the problem ?!!
    Regards

    Yes the clients are not able to see the SSID broadcasted by the AP.
    But these APs were functioning normally before without any changes to the WLC config.
    I had the same problem with other APs but they went back to normal state after a hardware reset to the APs.

  • WiSM Status LED 1 & Status LED 2 showing off. Is it normal?

    Hi,
    WiSM WLAN Service Module WS-SVC-WISM-1-K9 in 6509e running VSS IOs s72033-ipservicesk9_wan-mz.122-33.SXI2a.bin having trouble to get the IP from service-vlan DHCP also status LED 1 & Status LED 2 showing off.
    The pertinent config is as follows.
    vlan 300
    name WiSM_Service_Vlan
    interface Vlan300
    description *** WiSM Service-Vlan
    ip address 192.168.200.1 255.255.255.0
    ip dhcp excluded-address 192.168.200.1
    ip dhcp pool WiSM_Service-Vlan_300
       network 192.168.200.0 255.255.255.0
       default-router 192.168.200.1
    wism service-vlan 300
    vlan 183
    name WiSM_Management
    interface Vlan183
    description *** WiSM Management Vlan ***
    ip address 10.39.139.254 255.255.255.0
    wism switch 1 module 4 controller 1 allowed-vlan 125,126,183,300
    wism switch 1 module 4 controller 2 allowed-vlan 125,126,183,300
    wism switch 2 module 4 controller 1 allowed-vlan 125,126,183,300
    wism switch 2 module 4 controller 2 allowed-vlan 125,126,183,300
    wism switch 1 module 4 controller 1 native-vlan 183
    wism switch 1 module 4 controller 2 native-vlan 183
    wism switch 2 module 4 controller 1 native-vlan 183
    wism switch 2 module 4 controller 2 native-vlan 183
    HO2NET0001#sh wism status
    Service Vlan : 300, Service IP Subnet : 192.168.200.1/255.255.255.0
          WLAN
    Slot  Controller  Service IP       Management IP    SW Version  Status
    ----+-----------+----------------+----------------+-----------+---------------
    20    1           0.0.0.0          0.0.0.0                      Service Port Up
    20    2           0.0.0.0          0.0.0.0                      Service Port Up
    HO2NET0001#sh module
    Mod Ports Card Type                              Model              Serial No.
      1    8  CEF720 8 port 10GE with DFC            WS-X6708-10GE      SAL13442Q5N
      2    8  CEF720 8 port 10GE with DFC            WS-X6708-10GE      SAL13442GAL
      3   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL13410N8P
      4   10  WiSM WLAN Service Module               WS-SVC-WISM-1-K9   SAD133101UY
      5    5  Supervisor Engine 720 10GE (Active)    VS-S720-10G        SAL13442JE4
    Mod MAC addresses                       Hw    Fw           Sw           Status
      1  0025.84f1.55b8 to 0025.84f1.55bf   2.1   12.2(18r)S1  12.2(33)SXI2 Ok
      2  0025.84f1.4e58 to 0025.84f1.4e5f   2.1   12.2(18r)S1  12.2(33)SXI2 Ok
      3  0027.0da7.c240 to 0027.0da7.c26f   3.2   12.2(18r)S1  12.2(33)SXI2 Ok
      4  0023.5e25.7168 to 0023.5e25.7177   2.3   12.2(14r)S5  12.2(33)SXI2 Ok
      5  001f.9e2a.2608 to 001f.9e2a.260f   3.1   8.5(3)       12.2(33)SXI2 Ok
    Mod  Sub-Module                  Model              Serial       Hw     Status
      1  Distributed Forwarding Card WS-F6700-DFC3C     SAL13442EG9  1.4    Ok
      2  Distributed Forwarding Card WS-F6700-DFC3C     SAL13442H9T  1.4    Ok
      3  Centralized Forwarding Card WS-F6700-CFC       SAL13442HU9  4.1    Ok
      4  Centralized Forwarding Card WS-SVC-WISM-1-K9-D SAD133200D6  2.1    Ok
      5  Policy Feature Card 3       VS-F6K-PFC3C       SAL13442E5S  1.1    Ok
      5  MSFC3 Daughterboard         VS-F6K-MSFC3       SAL13421AJZ  2.0    Ok
    Mod  Online Diag Status
      1  Pass
      2  Pass
      3  Pass
      4  Pass
      5  Pass
    HO2NET0001#sh vlan
    300  WiSM_Service_Vlan                active    Gi1/4/9, Gi1/4/10
    The service IP is supposed to have been populated with an address from the dhcp pool. I am also unable to connect to access it by console as well as doing a session switch 1 slot 4 processor 1. I get the following upon attempting to do so:
    Through Console.
    It is giving following & then got stuck.
    Bootloader 3.2.202.0 (Nov 13 2007 - 19:35:12)
    Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200020
            CPU: 999 MHz
            CCB: 333 MHz
            DDR: 166 MHz
            LBC: 41 MHz
    L1 D-cache 32KB, L1 I-cache 32KB enabled.
    I2C:   ready
    DTT:   1 is 33 C
    DRAM:  DDR module detected, total size:512MB.
    512 MB
    8540 in PCI Host Mode.
    8540 not PCI Arbiter.
    Memory Test PASS
    FLASH:
      Flash Bank 0: portsize = 2, size = 8 MB in 142 Sectors
    8 MB
    L2 cache enabled: 256KB
    Card Id: 1537
    Card Revision Id: 1
    Card CPU Id: 1287
    Number of MAC Addresses: 32
    Number of Slots Supported: 4
    Serial Number: FAM133200D6
    Manufacturers ID: 30464
    Board Maintenance Level: 00
    In:    serial
    Out:   serial
    Err:   serial
                          .o88b. d888888b .d8888.  .o88b.  .d88b.
                         d8P  Y8   `88'   88'  YP d8P  Y8 .8P  Y8.
                         8P         88    `8bo.   8P      88    88
                         8b         88      `Y8b. 8b      88    88
                         Y8b  d8   .88.   db   8D Y8b  d8 `8b  d8'
                          `Y88P' Y888888P `8888Y'  `Y88P'  `Y88P'
                        Model SVC-WiSM   S/N: FAM133200D6
    Net:   TSEC ETHERNET
    IDE:   Bus 0: OK
      Device 0: Model: STI Flash 8.0.0 Firm: 01/17/07 Ser#: STI1MMJ109198093647
                Type: Removable Hard Disk
                Capacity: 488.7 MB = 0.4 GB (1000944 x 512)
      Device 1: not available
    Booting Primary Image...
    Press <ESC> now for additional boot options...
    Detecting Hardware . . .
    Cryptographic library self-test....passed!
    XML config selected
    Validating XML configuration
    Cisco is a trademark of Cisco Systems, Inc.
    Software Copyright Cisco Systems, Inc. All rights reserved.
    Cisco AireOS Version 5.2.178.0
    Initializing OS Services: ok
    Initializing Serial Services: ok
    Initializing Internal Interfaces: ok
    Initializing Network Services: ok
    Initializing Licensing Services: ok
    Starting ARP Services: ok
    Starting Trap Manager: ok
    Starting Network Interface Management Services: ok
    Starting System Services: ok
    Starting FIPS Features: ok : Not enabled
    Starting Fast Path Hardware Acceleration: ok
    Starting Switching Services: ok
    Starting QoS Services: ok
    Starting Policy Manager: ok
    Starting Data Transport Link Layer: ok
    Starting Access Control List Services: ok
    Starting System Interfaces: ok
    Starting Client Troubleshooting Service: ok
    Starting Management Frame Protection: ok
    Starting LWAPP: ok
    Starting CAPWAP: ok
    Starting Certificate Database: ok
    Starting VPN Services: ok
    Starting Security Services: ok
    Starting Policy Manager: ok
    Starting Authentication Engine: ok
    Starting Mobility Management: ok
    Starting LOCP: ok
    Starting Virtual AP Services: ok
    Starting AireWave Director: ok
    Starting Network Time Services: ok
    Starting Cisco Discovery Protocol: ok
    Starting Broadcast Services: ok
    Starting Logging Services: ok
    Starting DHCP Server: ok
    Starting IDS Signature Manager: ok
    Starting RFID Tag Tracking: ok
    Starting WLAN Control Protocol (WCP): ok
    Starting Mesh Services:  ok
    Starting TSM: ok
    Starting CIDS Services: ok
    Starting Ethernet-over-IP: ok
    Starting DTLS server:  enabled in CAPWAP
    Starting FMC HS: ok
    Starting WIPS: ok
    Starting SSHPM LSC PROV LIST: ok
    Starting Management Services:
       Web Server: ok
       CLI: ok
       Secure Web: Web Authentication Certificate not found (error). If you cannot access management interface via HTTPS please reconfigure Virtual Interface.
    (Cisco Controller)
    Welcome to the Cisco Wizard Configuration Tool
    Use the '-' character to backup
    Would you like to terminate autoinstall? [yes]:
    AUTO-INSTALL: starting now...
    Through Session
    HO2NET0001##session switch 1 slot 4 proc 1
    The default escape character is Ctrl-^, then x. You can also type 'exit' at the remote prompt to end the session Trying 0.0.0.0 ...
    Any assistance or ideas offered will be greatly appreciated.
    Thanks,

    Hi Tabish,
    How many times do you have to open this same topic?
    In my opinion, this is your THIRD thread for the same topic.

  • Status bar turned red

    While I was using my iPad, the status bar at the top (the black bar all the way at the top with the clock) suddenly turned red for a very brief moment.  Out of the corner of my eye, I saw some words there.  But when I shifted my focus to read what was there, the words disappeared and the bar turned back to it's normal black.  So I have no idea what this was all about; it was so quick.  But it was obviously a warning of some sort.
    Anybody know what this could have been?

    I found it.  It says "Garage Band Recording.". Strange, considering it pops up after quitting the app.

  • FP-1600 Status LED blinks 17 times.

    My FieldPoint bank has 9 modules. I previously had a problem with the FP-TB-10 power and ready lights blinking, but that was because one of my dual-channel modules was not seated correctly. Now the status LED is blinking 17 times. The manual says to contact NI about this. The FieldPoint Explorer seems to find all of the modules correctly, though. Anyone know what's up?

    Aaron,
    I checked the firmware and the FieldPoint Explorer version, and I'm using 3.20 and 3.0, respectively. When I power cycle the FP-1600, the 17 blinks of the status LED go away. Communication works, and all of the devices are found. However, communication does drop out from time to time, and eventually the status LED begins blinking 17 times again.
    A possibly related issue is that the FP-AI-V10 dual-channel module that I have plugged into slot 2 of the FP-TB-10 base causes the FP-TB-10 to flash its power and ready LEDs. Re-seating the FP-AI-V10 seems to fix this, although the module is definitely already clicked into place when I see this problem. Upon reseating (or just pressing on it without removing the module), the FieldPoint Explo
    rer program finds this module.
    I'm tempted to think that this issue with the FP-TB-10 and FP-AI-V10 are unrelated to the FP-1600's status LED blinking 17 times because even with the FP-TB-10 removed from the bank, I still get the flashing LED.
    Any ideas? Also, what is a GPF type error?
    Thanks,
    Jake

  • My z10 led flashing red when charging and even at battery full it blinks red. no green at any note..

    My z10 led flashing red when charging and even at battery full it blinks red. no green at any notification. But at below 10% charging level it blinks with a combination of red and green. Please send me any settings to be changed if.. at full charged no green light is blinking.. how many colours does z10 led have..and when it works and how to make those settings..or was my led not working fine? I am worried so much..plz help me

    Your LED is fine, on the Z10 there is not "network signal available" green LED, as you're accustomed to from the legacy devices. At reaching 10%, the LED will blink orange.
    Red for message or applicaiton notifications.
    if you want to edit and create specific LED color combination, see the third party apps such as BeBuzz or Hub++
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

Maybe you are looking for

  • Variable For Query Key Date

    Hi All, I am using time dependent master data, i want to count number of employees on particular key date for diffferent Orgunits. So i created variable in the query properties for dynamic date selection .I also have other variable - Calendar month.

  • Camera wiggle wont respond, Ive been using after effects for over a year, absoloutley stumped ! help

    Ok, Exactley what the description said.. Ive been using AE for over a year but havent used cam wiggle since i was studying my course... I understand how it works i all click the null Position stopwatch then wiggle(12,34) etc (is that right ? ) But th

  • How to change the attributes of an XML file

    hi peeps 'ope you can help me here i need to change the attributes of an xml file, i parse it first using a DOM parser but i cant find a way to change the attributes in the XML file, setAttribute() works only at runtime and doesn't change the attribu

  • Developing reports in bw for basis

    hi all can we develop reports in basis in bw? shalini

  • Emailing photos in PE11

    When using PE11 for emailing photos I find that I can't edit the text part of the message.  Everything else works fine.  I never had this problem with PE5.