Super Slow Connection speed

Hi all, with any luck someone here will be able to offer some wisdom!
Until recently my broadband has been faultless (well not bad anyway), in the last week or so it seems to have nosedived in terms of performance, and I am struggling to work out why. I have been through India, and I have my modem plugged into the test port of the master socket, here is wat things look like in the Hub Manager:
Line state
Connected
Connection time
0 days, 0:53:56
Downstream
8,126 Kbps
Upstream
440 Kbps
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.5
Latency type
Interleaved
Noise margin (Down/Up)
20.3 dB / 32.9 dB
Line attenuation (Down/Up)
10.0 dB / 4.2 dB
Output power (Down/Up)
0.0 dBm / 12.0 dBm
Loss of Framing (Local)
34
Loss of Signal (Local)
3
Loss of Power (Local)
0
FEC Errors (Down/Up)
0 / 4294967264
CRC Errors (Down/Up)
0 / 2147480000
HEC Errors (Down/Up)
nil / 0
Error Seconds (Local)
3
The three errors are me pulling the cable out to rest the conenction. The massive FEC / CRC errors are a bug I think. Does anyone know about Loss of Framing and what 0dBm output power are?
I ran the BT speedtest and got some truly terrible results, which said that my profile was 7000kbps, good, and my download was 146kbps, bad.
Anyone know what might be causing my super slow connection? I disconnected all computers barring my laptop in case somethign was secretly thrashing the service, but it didnt help.
Thanks in advance,
Mark.

I have similar problems. My connection was fine until about a week ago, when I started getting noise on my phone.
This has now been fixed, but since then, my Broadband connection speed has dropped from around 2M to 135k. I had an engineer out this morning to check what had been fixed during the first engineer visit (to fix the phone) and once he'd finished, he tested in to the socket to find that he could get 7M speeds. However, since he's been gone, I've plugged my setup back in and still get speeds of 135k.
I've tried removing phone connection so only router plugged in, I've changed filter to see if that was the issue - only things I've not yet tried because they are more hassle first off is trying another ADSL cable and/or a new router
My Hub manager shows the following, but not sure if this helpful to anyone, or if anyone can point me in the right direction of other things to try, I'd be greatly appreciative.
Thanks
ADSL line status
Connection information
Line state
Connected
Connection time
0 days, 0:56:42
Downstream
8,128 Kbps
Upstream
448 Kbps
ADSL settings
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.1
Latency type
Interleaved
Noise margin (Down/Up)
15.7 dB / 22.0 dB
Line attenuation (Down/Up)
15.0 dB / 8.5 dB
Output power (Down/Up)
19.8 dBm / 12.3 dBm
Loss of Framing (Local)
34
Loss of Signal (Local)
3
Loss of Power (Local)
0
FEC Errors (Down/Up)
13 / 0
CRC Errors (Down/Up)
0 / 2147480000
HEC Errors (Down/Up)
nil / 0
Error Seconds (Local)
3

Similar Messages

Super Slow DSL Speeds

I have been without internet for a week. Verizon finally fixed the problem yesterday afternoon and my internet service was restored but now I have super slow DSL speeds. 0.36 dowload & 0.54upload.
I am tired of calling tech support and being told to reboot my computer, modem, yadda yadda. There is something else going on here and need to figure out if it is with the modem itself or the line. All the line tests the tech support people have done come back normal.
The modem is reporting the OAM ping test as failing in Far End F4 Loop Back Count & Near End F4 Loop Back Count. No idea what that means.....
The speed from the modem itself is listed as:
Speed(Down/Up):
416 / 640 Kbps
I've done ipconfig flush dns, ipconfig release, ipconfig renew, etc etc. In home agent is reporting a problem with the dsl signal and just instructs me to reset the modem which does not help.
The modem is old, GT704WG from verizon. I am thinking about going out and buying a new one but don't want to do that if it is not going to fix the problem. It just seems odd that last week internet speed was fine and now it is slow as hell.
I had no internet or phone this week which they are claiming it was due to a line being pinched when my house was re-stuccod in December(granted internet and phone worked fine up until last Sunday). Verizon went under the house and fixed the line, phone & internet came back on. When I logged onto the browser I was prompted to activate my verizon service( I guess because it had been out for a week). Did that, got onto websites but connection is extermely slow and I am at my wits end.
I've spent more time on the phone this week with the unhelpful verizon people then I spend all year talking to my relatives and I really don't want to call them back and sit on the phone for another 45 min to an hour.
Anything I can do to diagnose and possibly fix this?

I appreciate you taking the time to answer my post, however your tools do nothing to tell me what is going on nor am I going to schedule yet another repair.
This past week when I had a "repair" scheduled, I was told they would be out on wednesday to fix our problem. No time frame was given for when this repair would take place. My retired father waited at the house the entire day only to have the repair man show up at 4:30pm who told us it was too late in the day to wait 5 min for us to move some boxes out of the closet that were over our crawl space so he could go under the house and fix the damaged wire. Instead he ran a long phone line from our box to our kitchen phone, told us this was a temporary solution and that if we called the repair center in the morning someone would come out in the morning and fix it.
We called in the morning, only again to be given no time frame for the repair. My father again waited all day, this time no one showed up. Even after he called 3 x's that day trying to get information on when the tech would be there....
Finally on Friday after spending another entire day waiting for a repair man did one show up around 3 in the afternoon one did, he went under the house and fixed the wire and our phone service was finally restored after 4 days. The dsl finally came back on albeit at a super slow speed as I am experiencing now.
Right now I am currently calling around to get rate quotes from other providers for our phone, internet, tv, & wireless. My experience with your "customer support" has soured me to verizon even though I have been with you guys for 10 plus years. I don't want to spend one more day waiting for repair man who may or may not show up. I don't want to spend another hour to hour and a half on the phone with some man in India who is just going to ask me to reboot my pc and modem over and over again and run a "line test" which is the same thing your automated phone service asks you to do as well.
Your company just doesn't get it when it comes to customer service. I pay my bill every month on time and in the 10 plus years I've been with you this is one of three times I've called for support. Each time I've had a horrible experience and the only thing that has kept me with you is that most of the time the service works as it should. I have heard FIOS is relatively trouble free, at least in my neighborhood, which is the only reason I am still considering the upgrade but if I do find a more reasonable deal with a company that has a better record for customer service I will be cancelling my order. I have a few weeks left to decide. It's unfortunate too because there are some nice folks that work at verizon but your company philosophy towards customer service has changed the bigger you've gottena and you've lost touch with what your customer's need from you.

WRT160N SLOW CONNECTION SPEED

I have slow connect speed when using the WRT160N. I have tried every thing, done dianogstics on connection, router, modem, thru three diffeant software, norton, windows, system machinics. when ising the router some days the speed is amost like using dial up
I use XP, on both a laptop desk top, up to date drivers, both cna use wifi or direct connection by cat 5e, 3 m of ram, a wimax internet server,,,,, (company called Bridge Maxx)
But when I stop using the router and connect directly to the modem no problem works fine,,,,, not sure what to do........ just need my wifi back,,,,so i cna work,

Whats the Version number of your Router, If you have having version2 router, then there is an knows issue with Version2 Router. Downgrading to Build 8 is generally accepted to correct these issues, however Linksys have indicated to several people they do not have the build 8 firmware to give to end users.
This is ONLY for WRT160N V2 routers. This firmware will not work on WRT160N V1.
You can find it at http://audipages.com/router/
Follow the dowload and firmware downgrade instructions on that page.
Once you upgrade the firmware of your router, you need to Reset your Router and Re-Configure all the settings on it back again. Once you do the settings on your router i think this should solve your problem.

Help : very slow connection speed with AEBS and iMac

I connect to the internet using my newly purchased AEBS. I have a MacBook and an 24" iMac ( purchased in Nov 2007). My iMac showed very slow connecting speed of <1 MB/s download; with my MacBook placed just 1 foot from my iMac, the MacBook showed an amazing download speed of 20MB/s. If i connect the iMac to the AEBS using ethernet cable, it can get a very high speed.
So, where is the problem??
I am new to wireless, please help. I use iMac more than my MacBook at home.
Actually, i did not touch the any of the advance setting of the AEBS.

You know, I am experiencing the same problem. My wife's PC and iPhone are blazing fast, but my MacBook is accessing the internet at about dial-up speeds. Very frustrating and I haven't yet found the culprit.
Anyone???

Since upgrading to Lion, my MacBook Pro is super slow connecting to Wi-Fi. Not so with Daughter's Snow Leopard or Wife's Dell. Any ideas?

Since upgrading to Lion, my MacBook Pro is super slow connecting to Wi-Fi (seems to search forever). This is not the case with my Daughter's MacBook (still on Snow Leopard) or my Wife's Dell (Windows 7). Any ideas?

Hold Option when you click on the Airport in the top bar & post the stats.

Slow connection speed imac but not macbook

Slow connection speed on my imac 2.4ghz intel core 2 duo running 10.6.8, I get download of 15mbs and upload of 9mbs but on my macbook pro 2.8ghz intel core i7 on the same desk I am getting 33mbs and 10mbs!
Can anyone help me out on this, thanks in advance.

The two key numbers here are: 1) Transmit Rate: 59 which is the current maximum bandwidth of the wireless connection in Mbps, and 2) The MCS Index: 6 which indicates that the iMac's connection to the BT Home Hub wireless is only using a single spatial steam. Forget the techo mumbo jumbo, your iMac is much more capable than that.
You should expect a Transmit rate closer to 130 Mbps on the 2.4 GHz radio. At least this explains the poorer performance of the iMac. I would venture to say that if you temporarily connected the iMac to the BT using an Ethernet connection the iMac would equal or exceed the MacBook Pro's bandwidth performance.
Has this always been an issue or something that has just recently started happening?

Im getting slower Connection speeds

Im getting slower connection speeds then what i ordered i got the 15mps and i only get 10 ?

It looks like you're right at the edge of the 10Mbps service limit for your copper line, as your margins are low and the line speed is incorrect.
Do you have access to a NID? If so, can you plug your modem into your NID's test jack and pull up the new statistics it shows? The NID can often times be found outside on the side/rear of your home, near your electrical panel/meter or on a pole near the street (uncommon for the last one).
========
The first to bring me 1Gbps Fiber for $30/m wins!

Slow Connection speed at all times, with regular d...

I would really appreciate any advice you have to offer! (P.s Connection time is so low because I recently connected the router to the test socket to see if there was a problem with my internal wiring)
I've been experiencing a slow connection speed (even though the router is connected to the master socket) much slower than with my previous provider and a very intermittent service. The broadband connection seems to drop out every time the landline is in use and when using the landline you can hear a lot of static/crackling in the background.
Connection Information
Line state:
Connected
Connection time:
0 days, 01:32:51
Downstream:
1.12 Mbps
Upstream:
444.9 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
5.4 dB / 8.6 dB
Line attenuation (Down/Up):
29.6 dB / 14.8 dB
Output power (Down/Up):
19.4 dBm / 9.9 dBm
FEC Events (Down/Up):
1412 / 0
CRC Events (Down/Up):
0 / 32
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
0 / 131
Error Seconds (Local/Remote):
12 / 15
Test1 comprises of two tests
1. Best Effort Test: -provides background information.
Download Speed
937 Kbps
0 Kbps
1000 Kbps
Max Achievable Speed
Download speedachieved during the test was - 937 Kbps
For your connection, the acceptable range of speeds is 400-1000 Kbps.
Additional Information:
Your DSL Connection Rate :1146 Kbps(DOWN-STREAM), 444 Kbps(UP-STREAM)
IP Profile for your line is - 1010 Kbps
I would really appreciate any help and advice! (P.s the connection time is so low because I tried to connect the router to the test socket to check if the fault was with the wiring. The router is normally on 24/7 and these problems still occur)
Solved!
Go to Solution.

Hi and welcome to the forum.
Have you tried another known working telephone into that test socket without an ADSL fiter.
If you have done all that you will need to report to your comms provider, if its BT Retail you will need to call them on 0800 800 151 or 0330 123 4151 from a mobile phone.
They will mention about charges but as long as you have done as suggested and you have not damaged any of the incoming wiring there "should" be no charge. when you phone do NOT mention broadband once any noise on your line is solved then your broadband will improve
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Progressively Slower Connection Speed

Hi,
I'm having some difficulties with my BT Broadband speed. The connection is getting progressively slower. Each time the router recycles I get a lower connection speed.
According to the BT Wholesale checker I should be able to get 6.5-8Mbps but I've never seen > 3Mbps and am currently <2Mbps.
ADSL Max
Up to 7.5
6.5 to 8
Available
Fixed Rate
2
Available
I tried resetting the router tonight and got the following in my event log entries:
23:35:07, 15 Jul.
( 58.190000) ETHoA is up - VPI: 0, VCI:35
23:35:07, 15 Jul.
( 58.190000) DSL is up
23:35:06, 15 Jul.
( 56.710000) DSL noise margin: 9.00 dB upstream, 9.00 dB downstream
23:35:05, 15 Jul.
( 56.640000) DSL line rate: 448 Kbps upstream, 1984 Kbps downstream
23:34:43, 15 Jul.
( 34.020000) WAN Auto-sensing running.
The helpdesk details are:
1. Product name:
BT Home Hub
2. Serial number:
+068340+NQ33251108
3. Firmware version:
Software version 4.7.5.1.83.8.130.1.17 (Type A) Last updated 03/05/14
4. Board version:
BT Hub 4A
5. ADSL uptime:
0 days, 00:11:03
6. Bandwidth:
448 / 1984
7. Data sent/received:
2.0 MB / 8.0 MB
8. Broadband username:
[email protected]
9. BT FON:
Yes
10. 2.4 GHz Wireless network/SSID:
BTHub4-7QH7
11. 2.4 GHz Wireless connections:
Enabled (802.11 b/g) 20 MHz, WPS enabled
12. 2.4 GHz Wireless security:
WPA and WPA2
13. 2.4 GHz Wireless channel:
Automatic / 1
14. 5 GHz Wireless network/SSID:
BTHub4-7QH7
15. 5 GHz Wireless connections:
Disabled
16. 5 GHz Wireless security:
WPA2
17. 5 GHz Wireless channel:
Automatic / 0
18. Firewall:
Default
19. MAC Address:
cc:33:bb:d0:29:00
20. VPI/VCI:
0 / 38
21. Modulation:
G.992.1 Annex A
22. Latency type:
Interleaved
23. Software variant:
24. Boot loader:
I have a shielded cable connecting the router to the line-box and the line-box has an ADSL filter faceplate which ought to mean I don't need filters anywhere in the house. This was fitted by a BT engineer.
I would be grateful if anybody could make a recommendation as I've tried everything I can think of.
Thanks in advance,
Simon Burrows
Solved!
Go to Solution.

Hi,
I've left the router up for several days now with no decrease in connection speed:
5. ADSL uptime:
7 days, 00:01:00
6. Bandwidth:
448 / 1984
I've tried the quiet-line test with a corded phone and get a constant buzz.
The next thing I've tried is to disconnect the ADSL filter faceplate from the line-box and have plugged a different ADSL filter directly into the line-box. The quiet-line test still yields a buzz, albeit slightly quieter.
Now that I've reset the router (turned it off whilst swapping cables around), I now have the following (with a different ADSL filter):
00:00:08, 23 Jul.
( 65.750000) DSL noise margin: 10.00 dB upstream, 9.00 dB downstream
00:00:08, 23 Jul.
( 65.680000) DSL line rate: 448 Kbps upstream, 1952 Kbps downstream
5. ADSL uptime:
0 days, 00:02:53
6. Bandwidth:
448 / 1952

WDS slow connection speed

I have a New Mac Pro Tower connected to an AX b/g compatible WDS network and it gets 10k kbps download speeds.
The Problem is my iMac G5 connected to the same network has an extremely slow download speed of 583 kbps?
Anyone have a clue as to why iMac's internet connection speed is so much slower?

I have had the same problem since november 2007:
I connected an old airport extreme basestation and a brand new one through WDS.
it took me a while getting the WDS to be faultless. (the encryption caused issues). So with both in WEP mode I lost the last error messages and both devices tell me all is fine, but it isn't.
I have NO access to the Internet via the router. I have no access to anything on the other side. The same goes when I hoop up in the other side then I have no access to devices (IP-Cam, printers, routers, Mac's, PC's...).
What is wrong with WDS?
I removed the old aiport extreme and used only a TimeCapsule and the new Airport Extreme. Nothing changed.
The Internet is extremely slow and gives time outs.
Finally I pulled a 60m cable to the TimeCapsule

Slow connection speed, 3rd time in 2 Months

Getting pretty sick of this now it has happen 3 times now in 2 months, my connection speed has dropped to 0.20Mbps. What's going on, it's has never happened between 2004 to September 2012, It's stopping me from playing online games, it takes ages to load webpages and it takes ages to load youtube videos even in 240p. and nothing has been changed or moved.
My router is a BT voyager 2091, I tried the BT speed checker, but they said my connection was too slow -.-
Current results:
Help?!
Thanks Ben
Solved!
Go to Solution.

Microfilter install correctly to an older master socket, quiet line test had no problems, no noise, no hissing.
Hope this helps more
Ben

WRT54G3G-ST very slow connection speeds

Hi,
I recently purchased a wrt54g3g-st router for mobile broadband and I have had some problems with the connection speeds. I have called linksys support but they were no help. I am using a PC-5740 broadband card which works perfectly fine in laptops by itself. When I am connected through the router its shows that I have 54.0 Mps speed but the pages load about as slow as dial-up speeds
Thanks for any help you can give me on this problem

if loading the pages is the only problem then try adjusting the mtu settings on the router ui to 1392 ....

Super slow connection

Having problems with my system somewhere. Cable modem connected to Airport Extreme, which is connected via ethernet to my iMac. Connection speeds are painfully slow. 2.5-3MBPS. When I pull the airport from the network and wire directly to the modem, I get 16-20MBPS. All I can think of to do is to plug the imac and the airport into a switch connected to the cable modem, and split the signal before the wireless broadcast begins. Any other thoughts would be much appreciated.

hired gun design wrote:
I'm pretty much at a loss as to how to proceed.
I'm getting there too... some of this amounts to grasping at straws but here's what I'd do:
Turn off your iMac's Airport to avoid confusion. If your connection speed is that slow I'm wondering if it's actually connecting to a distant wireless network so just turn it off to be sure.
See what IP address your iMac is getting when connected directly to the modem. It ought to be the same address the modem would issue the Extreme. Is it? Remember to unplug the modem, thus giving it time to reset its memory first. If you don't know how to determine your iMac's IP address look at this: How do I find my Mac OS X Leopard 10.5's IP address?
Then, find out what address it has when connected to the Extreme. It ought to be supplied by the Extreme, and within its DHCP address range i.e. not "self-assigned". I don't think anything would work if that were the case anyway.
Try resetting the Extreme. Sometimes an internal parameter that you simply can't see or change using Manual Setup gets corrupted, and the only solution is to wipe the slate clean.
Have you updated its firmware? I'm not aware of any recent firmware updates that would cause this kind of behaviour but why not rule out this potential cause.
Try a different Ethernet cable. I know you're thinking that can't possibly be it but defective cables had me flummoxed more than once.
Lastly your Extreme might simply be defective. No way to confirm that without substituting another.

Super slow share speed on FCP7

Anybody else experiencing insanely slow share speeds in FCP7? It's probably just my machine, but I thought I'd ask. I have a iMac Core2Duo 2.1ghz with 128meg ATI Radeon. I was super excited about this feature but it wants to take 70 minutes to burn a 1 minute, 30 second DVD.

I'm exporting a 2 minute DV 4x3 NTSC Sequence. All I am doing is just going to file menu - share - burn dvd. No fancy menu, nothing like that. It takes at least 70 minutes to encode.
The funny thing is - if I export the video as a QT Movie then do the same action in Compressor, it encodes the video in 4 minutes burns a DVD in about 7 minutes after that. With the exact same settings I used in the Share Menu through Final Cut Pro.
I'm a little baffled by this. I tried it on both a MacBook 2.0 (the last generation with the NVidia Graphics Card) and on my iMac 2.1ghz Core 2 Duo. Same result. The iMac has 2.5 gig in ram.
I hope this is just a badly written bug......

Mavericks install incomplete. No Apple installers on HD. Will I be able to upgrade to Yosemite and will it fix all that didn't install with Mavericks upgrade? Very slow connection speeds 30 hrs to download Mavericks. Tried re-install; no help/

Ever since upgrade to Mavericks I have been having problems which are too numerous to mention. I finally found a program from a UCBerkley professor called Pacifier which indicated 4000+ of 400,000+ files and folders did not install. I was unable to go further to try to fix everything because Pacifier can't find ANY Apple installers on my HD. It recommended I download the Mavericks installer without reinstalling to continue; however, after having done so (very slow connection; takes 30 hours to download) and although the installer appears in apps while downloading it disappears and NO Apple installer packages can be found on my hard drive. I tried to download Yosemite once and it indicated my system wasn't eligible for the upgrade. Its' download time was similar to Mavericks; 28+ hours.
I am using a Macbook Pro mid-2012 version OS X 10.9.5 (13F34); Processor 2.5 GHz Intel Core i5; Memory 4 GB 1600 MHz DDR3; Graphics Intel HD Graphics 4000 1024 MB.
Regardless of how many files and apps I remove my memory is being eaten up to the point I can hardly do anything at all. There are no civil words for how frustrated I am. Someone please help me.
Thanks,
JJ

Install Mavericks, Lion/Mountain Lion Using Internet Recovery
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Internet Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
Partition and Format the hard drive:
Select Disk Utility from the main menu and click on the Continue button.
After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
Reinstall Lion/Mountain Lion. Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Install button. Be sure to select the correct drive to use if you have more than one.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
This should restore the version of OS X originally pre-installed on the computer.

Super Slow Connection speed

Similar Messages

Maybe you are looking for