Superdrive: plays CDs, visible in Disk Utility, not visible in Finder

I was burning a data DVD of photos when the machine shut off. I wasn't watching it and I didn't notice that the battery was almost dead. It powered down and after I turned it back on Finder hasn't known how to let me view any burnt data discs. I successfully burned another data disc that was readable by another Macbook Pro, but when I pop in a blank disc, finder does nothing, and won't let me browse the contents of any data disc. I have not tried a video DVD. I can see the drive in disc utility and can right click on a file to burn it to disc, but it doesn't show up in the left pane of Finder.

Welcome to Apple Support Communities.
Check Finder Preferences to see if CDs, DVDs and iPods is checked.
Open Finder, and click on the word Finder in the menubar and then select Preferences, Advanced
(I'm on "Snow Leopard" 10.6.7, so your Preferences might not appear the same as this image.)
{not complete image}

Similar Messages

Internal hard disk is not visible in disk utility in Macbook Pro

Hi All,
I am trying to repair my mac. But in disk utility, the hard disk is not visible to proceed. Its showing disk0 -> volume with only 1.79GB. and all the options are disabled. The capacity of my mac book pro was 500GB.
Please help me in solving this issue
Thanks in advance....

So you've booted into your Recovery partition and you don't see any drives in Disk Utility to select in Recovery mode?
If the drive cannot be repaired, it's likely dead and you'll need to purchase a new internal drive.
Good luck,
Clinton
MacBook Pro (15-inch Late 2011), OS Mavericks 10.9.4, 16GB Crucial RAM, Crucial M500 960GB SSD, 27” Apple Thunderbolt Display

Disk utility not recognizing HD

Hi,
I have a G4 PowerMac with two 80 GB hard drives. When I boot up the computer, it boots up from the primary drive and runs fine. At this time, both my primary and my secondary drives are accessible and visible.
However, when I boot up the computer using either the Tiger or Leopard DVDs and then run Disk Utility, it only recognizes my secondary hard drive and not my main hard drive.
Also, if I quit Disk Utility at this time and tell it to re-start, it asks me which drive to boot from and the only option is either the DVD or the secondary hard drive. It just doesn't even see my main hard drive. I have to eject the DVD and re-boot for it to boot from the primary drive again.
Any advice?

I can see and use the hard drive only when I boot from it. When I boot from it, it is on my desktop, in my System Profiler, and visible under Disk Utility.
When I boot from DVD, the drive is not visible anywhere - not in System Profiler and not in Disk Utility.
I booted the computer using the HD and did a "Verify Disk". It gave me several errors and one in red that told me I needed to do a disk repair. I did a disk repair by booting the computer into Safe Mode (which performs a disk repair automatically). Then I rebooted regularly (from the HD) and went into Disk Utility and did another "Verify Disk". This time it verified successfully. I also repaired permissions successfully.
However...
when I booted from DVD, the drive was again invisible.

Copy to disk utility not working right

My disk utility not work like it used to, it does not show up a disk when I put it in the drive. And I can't copy to disk anymore. A blank disk shows up as a removeable drive instead of a blank disk on the disk utility...??? I need to fix this so I can back-up my files and free up some space, help please?
Dual 1.42 GHz PowerPC G4 Mac OS X (10.3.9) 2MB L3 cache per procesor 1.5 GB DDR SDRAM extra 250G HD

Hi-
The last time I saw a similar problem to yours, he was also running Panther. I advised reinstalling the 10.3.9 combo update, and his woes were gone.
http://www.apple.com/support/downloads/macosxcombinedupdate1039.html
Another thought is to check System Preferences/CD's & DVD'S, and check your selection nuder "When you insert a blank CD" (or DVD).
Running Disk Utility from the install disk, and repairing permissions is also another possible fix.
G4 AGP(450)Sawtooth Mac OS X (10.4.8) 2ghzPPC,1.62gbSDRAM, ATI9800, DVR-109,(IntHD)120&160,LaCie160,23"Cinema Display

OS X Disk Utility not recognizing Seagate 3TB drive in dock

Model Nhjgjhgjhgh
OS X Disk Utility not recognizing Seagate 3TB drive in dock
Been scouring the webs and can't quite figure this one out.
I just purchased a Seagate 3TB drive intending on using it for Backup.
Ended up plugging it into a dock and couldn't get it to show up in Disk Utility..
Interesting enough, I plugged this into an HP laptop and it displays just fine.
Anyone know the solution?
OS X 10.10 Yosemite, MacBook Pro (Retina, 15-inch, Early 2013)
Hardware Overview:
Model Name: MacBook Pro
Model Identifier: MacBookPro10,1
Processor Name: Intel Core i7
Processor Speed: 2.6 GHz
Number of Processors: 1
Total Number of Cores: 4
L2 Cache (per Core): 256 KB
L3 Cache: 6 MB
Memory: 16 GB
Boot ROM Version: MBP101.00EE.B05
SMC Version (system): 2.3f36

I hooked my internal as an external up to my Mom's Macbook Pro and it recognized my HD. I'm thinking it is something internal with the hook-up, which is awesome, because maybe I can actually fix it!!!! Any thoughts?

New IMac is crashing randomly because of "Panic Kernel Error." Now IMac startup disk is not visible and will not mount. What the story with this machine. Running 10.6.7

New IMac is crashing randomly because of "Panic Kernel Error." Now IMac startup disk is not visible and will not mount. What the story with this machine. Running 10.6.7

Almost certainly, some sort of hardware problem on your logic board.
Make an appointment and take it to your local Apple Store: http://www.apple.com/retail/geniusbar/

External hard disk does not show in finder

WD usb external hard disk does not appear in finder. Disk utility sees it and will mount/unmount and eject. I ran repair disk util. and all is well but still does not appear in finder

Hey Hatter, Thanx for the input.
Among other things I tried was a terminal routine someone suggested with no luck and new drivers/firmware for the drive, again, no luck.
I still don't know for sure what caused my problem, but I re-partitioned the drive and re-formatted it and that seemed to solve the provlem. Sadly, I lost all my info that was backed up on that particular drive but hopefully it won't come back to bite me later.
Cheers!!

My Startup Disk can not show in Finder.

My Startup Disk can not show in Finder.but it can be used in OSX normally.
So can I put it back to Finder?

If the startup disk is for Mac OS 9, neither MacBook nor PowerMac G5 can boot into 9. Only the PowerMac G5 can use Mac OS 9 in Apple menu -> System Preferences -> Classic.
Please be more detailed what sort of Startup Disk you are talking about, which operating system, and which machine this is a problem with.

External hard drive not visible in disk utility or finder

Hi all,
I have had a good look through previous discussions and I can't seem to find an issue relevant to mine.
My external hard drive has 2 partitions (1 time machine back up, 1 general hard drive). The issue is that the HD is running when it is plugged in however it is not visible in either disk utility or finder.
I am running OS X 10.10 (Yosemite) on a 2010 MacBook Pro. I also have parallels desktop running windows 7. When I boot windows and plug in the HD I usually get the option to mount the HD to either OS X or Windows. With this issue the option window appears for a split second (not enough time to select either) and then disappears. It seems that the HD may be ejecting itself as soon as it is registered by the computer. I have tried using a different power cable for the HD and also a different usb cable, this doesn't help.
The external HD is a Samsung D3 Station, which i have had for 6 months now and never had an issue with.
Any help is appreciated
Thanks,
Bruce

An update for anyone who can help me:
I have tried the external hard drive in other computers (mac and windows), each time I get the same problem above.
I have removed the HD from the enclosure and purchased a docking station for it (3.5" SATA). When I plug it in to the laptop it disconnects itself straight away before it is visible. With the windows computers it installs the drivers and says that the device is ready to use, then disconnects before it shows up.
As the HD is not visible there is no option to re-format or anything.
This is very frustrating as I was using the HD with no issues and it randomly disconnected and I have not been able to access since.
Thanks in advance for any help.
Bruce

External hard drive suddenly became "unreadable" and the disk utility offers not repair options. The drive is visible in disk utility but may not be mounted... any suggestions?

I have a WD My Passport 070A Media 2.0 TB external hard drive that has suddenly become unreadable on my laptop (MacBook Pro circa 2006 with 10.4.11) and I have tried on a MacBook Pro 2011 running 10.6.8 with the same results. I had tried opening disk utility to repair the drive, but on both machines the drive is visible in the left column, with no indentation below the drive. When I select the drive in the first aid portion the only options highlighted are info and eject... I was wondering if anyone had any suggestions to repair the drive. I am currently in Belize and am not home for 3 weeks yet. I'm hoping for a fix while I am down here, otherwise I may have to wait... I appreciate any assistance!
-Christina

Hi Christina,
It's quite possible the AC PSU has given out, if It's only Bus powered as it appears, that's the worst idea ever & asking for eventual problems.
What Format is it?
Did you install any WD SW?
Your best bet is DiskWarrio...
http://www.alsoft.com/DiskWarrior/
But others that may work…
Drive Genius…
http://www.prosofteng.com/products/drive_genius.php
TechTool Pro…
http://www.micromat.com/index.php?option=com_content&task=view&id=31&Itemid=83

IMac G5 17" is DOA... drive not visible in Disk Utility

About a week after my computer went out of warranty (OS 10.3.9), I have been experiencing random complete system meltdowns every 5 or 6 months. It begins while using the search feature, the beachball spins for 8-10 minutes then pulls search results. Following that, the system stalls on every task, and restarts with the blinking "?" folder. In the past, a re-install of the OS was a frustrating, but simple solution.
Last Friday, this happened for the fourth and final time. Upon attempting to re-install the OS, the install froze, locking up the computer. When I restarted to try to re-install the OS, the drive was not visible in the Disk Utility. It isn't visible in any Mac utility that I have tried, nor Disk Warrior.
I just replaced the SeaGate 7200 hard drive with a refurbed one, and the problem continutes--the drive is not visible to the install.
Is this 2-year old Mac now a paperweight? With the market resale value of this machine only about $500-600, I can't stomach spending a third of that to have something repaired, for all of this to potentially happen again.
Is it terminal? Has anyone else experienced this?
I'm really bummed out. As a Mac user for the last 15 years, I can't bear the thought of spending another 2 grand on a computer that will let me down again. I'm tired of the Pee Cee world hazing me as it is, and episodes like this don't make it any easier. Someone please tell me there is a solution...
doug

It DID break down a week after I received a call from Apple asking me to purchase an extended warranty. I wouldn't make that up.
It's on 10.3.9 because, in typical Apple fashion, 10.4 came out a WEEK after I bought my computer. I never bought the upgrade software from Apple just out of anger that a new computer was shipped with obsolete OS installed when a new version was hitting the shelves so soon afterwards. I work on 10.4.10 here at the office, and never missed the "features" at home. For $179, it wasn't something that ever screamed to be a necessity for a home computer.
The drive wasn't necessarily refurbed, but it was "recycled" and bought cheap to find out if it could be a simple solution. For $35, it was an easy attempt to figure out what was wrong with the computer. It didn't solve the problem, and was much cheaper than throwing money at it without knowing what was wrong.
At this point, I'm trying to save this box from becoming landfill. I bought a Dell PC laptop this past weekend for a third of what I paid for this iMac, and when it breaks down or obsoletes itself in 2 years, it won't be so difficult to swallow getting rid of it for something new.
I'm going to open this up again this afternoon to check the test LEDs and see if I can spot anything.
Don't get me wrong, I love Macs, and always will, but I can't any longer justify spending $2000 on a home computer. They are disposable appliances, and if they aren't going to come from the factory with warranties long enough to last through their lifetime, then it's difficult to spend that much money on a computer than only needs MORE money spent to maintain functionality.
I'll post back with my findings later today after I crack this open. Thanks for the assistance so far.
doug

Hard drives not visible in Disk Utility

I decided to add two additional 1.5 TB drives to my (early 2008) Mac Pro, in addition to the two 1.0 TB drives already there. I have a Mac RAID card, but the drives were not configured into an array because I was having battery and setting problems with the RAID card as described in previous posts.
I perhaps got the the not so bright idea to reconfigure my system from scratch, so I put the two 1.5 TB drives in, created partitions via Disk Utility, and then took all the drives out. I then put one of the new 1.5 TB drives in only, and re-installed OS X. So far, so good. Then, I put all 4 drives in, including the previous 1.0 TB drive with OS X on it.
Interestingly, the system then booted to the old 1.0 TB drive with OS X, and then it 'hung' on something with the spinning icon. I shut it down, and then put the new 1.5 TB with OS X, but it would not start. I yanked out the RAID card, figuring it was not helping. I managed to put the Boot DVD in, and the system does boot to DVD. However, it cannot visualize any drive at all, only the two DVDs in Disk Utility.
I tried several things. One is hardware scan by holding the 'D' key on startup -> no errors.
I then tried resetting the PRAM holding the command-option-P-R keys, same issue - boots to DVD, but no drives.
I then tried resetting what I think is the SMC, which is a button on the motherboard down near where the memory slots, and there a green light comes on next to the STBY area.
I'm out of the Apple care warranty, and I guess I'll have to pay for support going into the Mac Store, but I am hopeful someone has an idea.
I wondered if the cable from the SATA connector to the motherboard was loose, but it appears intact. However, I'm not sure how to get the plastic cage off.

Good idea, but the RAID card is out, and even the original drives are not visible. There is some type of BIOS or some related error.

Disk Utility not creating Mac bootable CDs

Hi
I have a 2006 Mac Mini with a SuperDrive running Snow Leopard (10.6). I downloaded a Linux ISO and burnt it to a blank CD using Disk Utility (dropped the ISO on the Disk Utility window, then clicked Burn). The CD burnt and verified with no problems but when I restart, holding down the Option key, it does not see the CD and I'm only given the option to boot from the hard drive. Then, when Mac OS X loads it tells me it has detected a blank CD. The same CD works and boots perfectly ok in a Windows machine. The Superdrive itself seems ok as it can boot from a Windows XP CD.
Any ideas why this might be?
Thanks
Neil

Did the Linux disk come as a bootable Windows image?

Drive visible in Disk Utility but not Finder. Why?

I have a PowerMac G4 (mirrored drive doors) with 4 hard drives installed. 3 of the drives are set-up in a striped RAID array and the other one is my boot drive with two partitions. One one partition, I have OS X 10.3 and I can see the RAID drive fine. On the other partition, I fresh installed 10.4 but the drive does not appear on the desktop. Strangly, I can see the drive in Disk Utility and it shows me the mount point. I can even unmount and remount it but it still does not show up in the Finder. I had 10.4 server installed prior to the fresh 10.4 (not server) install and that showed it fine. I tried to see the drive in Terminal but also does not appear. Why does my drive appear in Disk Utility but not the Finder?

BDAqua wrote:
Yes, it needs the path to the drive...
:-/ Yes, I got the command in completely with the path to the drive like it states in the other post. I have no idea why it didn't recognize the command as I'm not as familiar with UNIX/Linux commands as I'd like to be.
Anyways... I found the cause of the problem (incase it happens to anyone else). Here's what happened:
The ownership on the root of my RAID volume was set to be read/write for me (under my proper username) and no access for anyone else including Admin. When I installed a fresh OS, the default user was Admin (who had no access under the previous OS). If I would've taken the time to set-up my proper account (with the same owner name as my previous OS) then it would've been visible again but since I didn't see it under the default Admin account, I stopped there to troubleshoot. Another way to make it visible was just to change the access privileges from my previous OS to be read/write for other users (or at least Admin). I would think that checking the box for "Ignore ownership on this volume" would've remedied that but for whatever reason, it didn't.
Thank you for all your help. I did learn a little even if it wasn't the direct solution. Now if only I could get Disk Utility to restore my old image without giving me crazy errors... But that's another issue altogether. ;-D

I deleted a partition on my macbook pro and now that space is not visible in Disk Utility

I had a dual boot setup on my 1TB drive on my macbook with a linux partition. I decided to delete the linux partition and free up some space for my OSX partition. I went into recovery mode and first erased the linux swap partition then the linux partition. Then I went into the partition tab on Disk Utility and clicked on the "-" button for each swap partition and linux partition. Now when I go into Disk Utility now though the 500 GB that should have been freed up is not visible and I cant resize the OSX partition to include the extra space.

Let it finish, then you can safely delete it.

Superdrive: plays CDs, visible in Disk Utility, not visible in Finder

Similar Messages

Maybe you are looking for