Support for CUCM 8.6 in B200 M3

Is the new B200 M3 a supported platform for deploying Cisco Unified Communication Manager 8.6?
The tested reference configuration available at Unified Communication virtualization wiki does not list B200 M3 as a supported platform . Please can anyone assist in identifying support for the platform or the timelines?
Thanks for the help.

I am affraid it's not yet supported.
http://docwiki.cisco.com/wiki/Unified_Communications_Virtualization_Supported_Applications
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6790/ps5748/ps378/prod_brochure0900aecd8062a4f9.html
GP.
Pls rate helpful posts !!

Similar Messages

CUCM 9.1 in VirtualBox - The hardware you are using is not supported for this product

I'm trying to load CUCM licensed through my work onto an oracle VirtualBox running linux redhat, and its unpacking linux fine onto the vbox, and passes the hardware test on boot but when it goes to load I'm getting the error "The hardware you are using is not supported for this product."
I have dedicated to the VM:
4GB ram
4 CPU's (tried 2 and 4)
80GB Hard Drive
What in the world could be jamming this up? Anyone else ever run this or know what the deal is?
Any input is appreciated, thanks!

We only support ESXi
Sent from Cisco Technical Support iPad App

Audio & Video Call Recording Solution for CUCM

Hi,
I am looking for a audio and video call recording solution for CUCM. The requirement is the recording system shall record all audio & video calls including incoming, outgoing, and station-to-station calls. One cirtical requirement is: The users on the CUCM system shall be able to record video calls for video equipped stations with a push of a button on their Cisco IP Desk set or their Cisco soft phone.
Does anyone know the product or third party vendor who supports audio and video recording for CUCM?
-Thanks
Vaijanath

Currently Cisco doesn't support video recording with a push of a button on their Cisco IP Desk set or their Cisco soft phone. Also, I have checked with the third party vendors and they only support the video recording using Passive Call recording (port mirroring).
http://www.verba.com/cisco-call-recording-solutions

What licenses do I need for CUCM and CME

Hi Experts,
I am a newbie to Cisco IP telephony and request your guidance.
My boss has asked me to order some 7942 phones for a CUCM based site and some 7942 phones for a CME based site.
For CUCM 9, I understand that we need an enhanced user licenses on CUCM side.
For the IP phone, I see 2 part numbers and am confused.
CP-7942G - Cisco Unified IP Phone 7942G
CP-7942G-CH1 - Cisco Unified IP Phone 7942G, for Channels, with one station user license
What is the station user license mentioned in the part number CP-7942G-CH1 ? Is it the same as the enhanced user licenses? Assuming i am ordering enhanced user licenses, what should I order CP-7942G or CP-7942G-CH1?
I also see a part number SW-CCM-UL-7942= ? What is this part? is it needed?
And what do I need for CME?
Is FL-CME-SRST-10 enough for the CME?
What is the part number for the phones? Is it CP-7942G or CP-7942G-CCME?
I also see another part number "SW-CCME-UL-7942="? What is it? And is it really needed?
I heard that Cisco simplified Licensing from version 9. At least it doesn't look simple to me :(
Can you please help me, Experts?
Thanks,
Pete

Hi without knowing your business goals, current network, etc here is some feedback.
Depending on your design, if the sites are connected via a reliable WAN you could run the branch site as SRST and not CME, this way you get a rich feature set of the centralised call manager and simplify licenses, etc.
Anyway, you need to size your CUCME (or SRST) correctly as each Cisco router hardware platform has a maximum supported handsets. If you have a SIP provider new purchased ISRs now come with 10 CUBE licenses other wise you will need something else such as a VIC for dial tone.
For instance the following is a router that comes with 25 CME
C2901-CME-SRST/K9
2901 Voice Bundle w/PVDM3-16,FL-CME-SRST-25,UC Lic,FL-CUBE10
You can add CP-7942G-CCME which is the physical phone and license for CME
Use CP-7942G= for the Call Manager Deployment as you will get UCL Enh or CUWL for the user side
If you have existing routers you will need to obtain upgrade licenses for voice/CME add DSPs if needed for conferencing, media termination, etc, CUBE or voice cards and you can add the phones.
Router handset capacities see Table 7
http://www.cisco.com/c/en/us/products/collateral/routers/2900-series-integrated-services-routers-isr/data_sheet_c78_553896.html
Hope this helps

Recording solutions for CUCM/CME.

Hi, all!
I have a questions about call recording solution for CUCM and CME.
- Does Cisco Media Sense support call recording for Call Manager Express?
- Will Media sense write all calls, including calls via PSTN to any DN, or only DN to DN calls?
- Can it be used for call recording in CUCM?
- Network-based call recording feature available only in CUCM 10 or early versions?
- What is disadvanteges and benefits of span/rspan call recording solutions?

Here are a few
http://www.telrex.com/callrex.htm?gclid=CM3p4_em5oQCFSfTJAodVxw8RQ
http://www.call-replay.com/?gclid=CLG277in5oQCFShsSQodtyXIjQ
Hope this helps.
Please remember to rate all replies

Cisco Unity Express (NME-CUE) Compatibility for CUCM 9.1.2

I unable to find latest Compatibility matrix for Cisco Unity Express (NME-CUE) module for integrating with CUCM 9.1.2
The URL: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/compatibility/cuecomp.html is updated with CUCM 9.0 only.
Request to share Compatibility matrix or suggest Hardware and software for my below requirement.
I am running NME-CUE 7.0.6 on 2951 ISR2 with IOS version 15.2(4)M5 and integrated with CUCM 7.1.5 using SCCP.
I am upgrading my CUCM to 9.1.2 and need suggestion on upgrading the CUE.
Also need details on Licensing for approx 100 Mailbox and 25 Voice Ports (No need of IVR Ports).
Thanks,
Chandan

Hi Chandan,
CUE 8.6.6 and later are compatible with CUCM 9.1.x;
Support for Cisco Unified Communications Manager 9.1
Cisco Unity Express 8.6.6 provides support for Cisco Unified Communications Manager 9.1.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/rel8_6/rel_notes/rel_notes86.html#pgfId-411381
Because you are moving from a pre-7.1 CUE version you will need to follow the CSL License migration process;
NoteWhen you upgrade to Cisco Unity Express Release 8.6.x from any release prior to Cisco Unity Express Release 7.1, you must replace your pre-CSL licenses with CSL licenses. You must migrate your licenses for the mailbox features and port features. If you have purchased the optional IVR features, you should also migrate your licenses for the IVR features.
Software Activation for Cisco Unity Express 7.1 and Later Versions
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/rel7_1/Licensing/CUELicensing_book.html
Cheers!
Rob

UCS C220 with raid v6 problem(not support any CUCM versions)

pease help me in the below problem
after installing UCS C220 with raid 6, i tried to make new v-machine for CUCM but it gives me the below message:
The hardware you are using is not supported for this product. installation will now halt.

Are you using the CUCM OVA?
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk

MeetingPlace support for Outlook 2010

We have a client running CUCM version 7.1.3.30000-1 and using Cisco MeetingPlace version 2.1.1.2.
When my client migrated their users to Office 2010, they have been unable to use Meeting place, they get the following error:
"unable to download, unspecified error web browser"
As I have read this MeetingPlace version does not have support for Outlook2010 plugins, and we would have to upgrade to MeetingPlace 7.1 in order to solve this problem
With this environment:
a) Does MeetingPlace 7.1 support Outlook2010 plugins??
b) Can we upgrade this meeting place version to a new one supporting Outlook2010 plugins??? Or We also would have to upgrade CUCM version??
Thank you
Enrique Villasana

Enrique,
1. Yes, MP 7.1 supports MS Outlook 2010. Please refer http://www.cisco.com/en/US/partner/docs/voice_ip_comm/meetingplace/7_1/english/release_notes/mp71rn.html#wp127737
2. If MP needs to be upgraded to 7.1 then CUCM needs to be at 7.1.5 ( in 7.x series ). Please refer http://docwiki.cisco.com/wiki/Cisco_Unified_MeetingPlace,_Release_7.1_--_Component_Compatibility_Matrix
Hope it helps ?
GP.
Pls rate helpful posts by clicking on stars below the post !!

FAC support for Linksys SPA962 phones.

Hi
We are running CUCM version 9.1 and few linksys phones are registered to this CUCM
Is it possible to configure FAC code for these linksys phones.
So that before dialing international call, FAC code is required.
Is these phones are supported cisco CUCM FAC features ? Is it configurable ?
Rgds
Rajesh Kumar

Rajesh,
Early media just means it can support a 180 Ringing or 183 Session Progress with SDP in order to establish a media connection prior to the call connect for things such as ringback and playing tones for FAC and such. What did you see in the CallManager traces for the call? Can you pull out all the SIP messaging for a test FAC call or just attach a packet capture from the phone?
Thanks,
Brian

SX80 support on CUCM

The datasheet for SX80 mentions 'Cisco Unified Communications Manager native support (requires Cisco Unified Communications Manager version 8.6 or higher)'. This is a bit misleading for customers / partners who are using CUCM version 9.1.1, because SX80 is not supported on CUCM 9.1.1. The following bug provides clear details of cucm versions which support SX80
https://tools.cisco.com/bugsearch/bug/CSCun04264
Support for Cisco TelePresence SX10 and SX80 on UCM
CSCun04264
Description
Symptom:
add support for Cisco TelePresence SX10 and SX80, a set of new products from CETG on UCM
Conditions:
Applicable to Cisco Unified Communications Manager (CallManager) releases 8.6(2),9.1(2),10.0(1)
Workaround:
None

Hi
Installing the firmware file does not add capability for a new type of device to CUCM, which is not natively present.
8.6.2.22900-9 by default does not have the capability for the 78XX series phone. In order to enable the phone on CUCM you need to install device pack on CUCM and then do a cluster reboot.
Following is link to compatilbility matrix for device pack
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/compat/matrix/CMDP_BK_CCBDA741_00_cucm-device-package-compatibility-matrix.pdf
Firmware file is only useful , if CUCM has the capability for the device and you want to upgrade the firmware.
So, yes, you will need to install the Devicepack you have mentioned above first to enable 7821 on 8.6.2 and then add the phone.
But ensure that installing the devicepack will upgrade the device defaults for other phones as well. You may want to take backup of your device defaults and revert those back to original before you go for reboot , in case you are not looking to upgrade other device firmwares as well.
Regards
Aditya Gupta

Reporting (Monitoring) Tool for CUCM 8.6

Hi ,
I am looking for a reporting or statistic tool for CUCM 8.6. , better we search a Monitoring tool .
Our main concrn is that we would like monitoring the Lines , the Phones , Calls (In und Out) , Count of Calls etc. not only print but a dashboard also .
Could you recommend me a programm by your experience ?
Thanks for your support
Homayoun

Here's a quick summary of what to do to view the number of registered phones per subscriber. There's lots more detail on all the available parameters in the docs from that link I gave above.
Open RTMT and select the Default profile. From the left hand window, select the "Performance" option.
This will open the Performance screen. Pick one subscriber from the list of nodes, expand it out, and then expand out the "Cisco CallManager" branch. Select and drag the Registered HardwarePhones option to one of the six blank squares.(You can adjust the divider to make reading the labels easier - but selecting the divider isn't always easy) You can repeat for all your other subscribers.
You can add extra tabs by selecting Edit (From the top-level menu bar) -> New Category.
GTG

IPod Reset Utility is not supported for use with Windows Vista??????

is there anyway to get pass this?
i need to use the ipod resetutility to reset my shuffle
but the only problem is that i have Vista and the program isnt
supported for vista. can someone help me out here?

well the only problem with that is that
everyone i know use vista -.-

Lack of support for Canon G7 and G9. Alternatives?

I am really disappointed about the lack of support for the Canon G9, and looking at the list of compatible cameras (http://docs.info.apple.com/article.html?artnum=306835) I notice that Canon G7 - even if it does not have a RAW format, is not supported either.
I am thinking that the purchase of the G9 may have been premature and that I may need to sell it and get another cam that is supported by Apple/Aperture.
What would you guys do? Is there a cam out there similar to the G9 at the moment that has a Apple-supported RAW format?
Best regards,
Kjell Are Refsvik

I think the camera closest to the G9 that has RAW support from Apple are the Panasonic DMC-LX2/Leica D-Lux 3 twins. Don't know where you are, but in the US, the Panasonic costs about $400. 10MP, 28-112mm (35mm equivalent) Leica lens, very compact body, and RAW output. The Leica costs $599, and has that classic look.
I don't know much about that cameras, but you may want to investigate.
Message was edited by: rkkwan
Message was edited by: rkkwan

Why no SyncML-support for Harmattan??

I've used SyncML on my N95 with memotoo.com for years. Worked very well. I took it for granted that SyncML would be supported on the N9. But alas, it isn't. I find that really incomprehensible. Worse yet, CalDAV syncing with memotoo doesn't work - I don't know who's to blame for this, but on the desktop it works flawelessly so I do have a suspicion. Even worse: there is no way to sync contacts using CardDAV.
MeeGo (the true MeeGo) has SyncML-support out-of-the-box. And the N9/N950 does have SyncML-support for bluetooth.
Yes, contacts syncing is supported for Ovi. And Google. And Facebook. But I do NOT want to use those services, because of grave privacy risks and because they use yet again some proprietary protocols.
I wonder, what where they thinking at Nokia for NOT supporting some well-known open standards??
(While I'm ranting: why is there ^%@$ Facebook and GTalk-support over XMPP, but no self-defined XMPP account?? Yes, you can add such accounts from the terminal, using mc-tool, but really that's just a kick in the teeth. And where's UPnP/DLNA-support?)

Hey Guys, Did you figure out any way to do PIM sync via SyncML on N9?
I am struggling to get things moving as I come from N8.
N9 just doesnt have any way to sync calendar, tasks with Ovi. Same with Notes.
Best Regards,
Suyog

ISE 1.2.1 support for Yosemite?

Hello all, just curious. I see in the release notes for ISE 1.2.X that support for Mac OS 10.10 (Yosemite) was available via patch 12 on the ISE1.2.0 train of code. That said, I see nothing in the release notes stating any support for Yosemite for any of the patches for ISE1.2.1, the latest being patch 3 released 1 week after ISE 1.2.0 patch 12. Can anyone please advise if Yosemite is in fact supported on 1.2.1 with patch 3??
Thank you very much in advance for your help
Jeff

Jeff,
OS X 10.10 is supported in ISE 1.2 p11, 1.2.1 p2 and 1.3.
Patch 12 for 1.2 and Patch 3 for 1.2.1 fix other issues for OS X 10.10, and I recommend updating to the latest patches for these fixes.
Here is the entry in the Release Notes detailing the fix for 10.10 in 1.2 p 12:
MacOsXAgent versrion 4.9.5.3 should be used and MacOsXSPWizard 1.0.0.30
Note that the description for these files denote ISE 1.2 Patch 11/12, ISE 1.3 release and above. ISE 1.2.1 is not mentioned, but follows the bug fix/release schedule for 1.2, with an adjustment.
1.2 patch 10 = 1.2.1 patch 1
Please Rate Helpful posts and mark this question as answered if, in fact, this does answer your question. Otherwise, feel free to post follow-up questions.
Charles Moreton

Support for CUCM 8.6 in B200 M3

Similar Messages

Maybe you are looking for