Support forCamcorders with USB and no fire wire.

I have the Panasonic SDX1h and have the same problem using Onloction as those that have the AG HC-150. The only difference is my camera comes with "web cam mode" and can be used for Skype. It does transfer data via USB. Onlocation recognizes the web cam but it does not generate a picture. I even tried the biggest badest min USB cord made for a GPS.

There is no way to use firewire for transfer on the video iPod, either the 5G or 5.5G. This has not been available on any of the iPod videos.
TTFN
Doc

Similar Messages

My iPad was disconnected during upgrade. I've tried restoring and resetting. I just did an iPad erase in "find my iphone" and it still shows the itunes logo and the fire-wire cable on the screen with an arrow. It's currently plugged into my computer.

My iPad was disconnected during upgrade. I've tried restoring and resetting. I just did an iPad erase in "find my iphone" and it still shows the itunes logo and the fire-wire cable on the screen with an arrow. It's currently plugged into my computer. How do I remedy this?

Unable to update or restore
http://support.apple.com/kb/HT1808?viewlocale=en_US

Canon 860 Series (Pixma) Printer Problems with OSX 10.8 (Mountain Lion) – links to Canon Support Site with Drivers and Software with install tips

After spending several hours sorting out Canon Pixma OSX problems here are my thoughts:
Canon 860 Series (Pixma 868) Printer Problems with OSX 10.8 (Mountain Lion) – links to Canon Support Site with Drivers and Software with install tips
Problem:
- New imac and MacBook Pro 2012 (OSX 10.8.2) had a problem using Canon Pixma 868 printer on network and would not scan or print using Canon Pixma software (Pixma MP Navigator 2.1 & Photo Print), which has advanced scanning and photo printing functions.
- When I connected the canon printer to my imac, OSX 10.8.2 automatically downloaded and installed drivers for Canon 860 series printer. I could then add the new printer (select ‘apple menu’ / ‘system preferences’ / ‘print and scan’ / “+”) and printer would work while connected via USB but could not get to print or scan over network wifi.
- The original Canon 860 Series CD does not work with 10.8 and the manual / online instructions did not make sense (as based on CD install).
Solution:
1) Install Canon Printer Drivers and Software (from official Canon site)
Go to canon support site, review FAQ, then download and install following Pixma 860 Series software & drivers for OSX 10.8 (links see below). The version I downloaded is in brackets but check for updated version. Full instructions are below.
Canon 860 Series Drivers & Software for OSX 10.8 Mountain Lion:
The base software and drivers needed for using Canon 860 Series on Mac OS X 10.8 (USB) are
1 Printer Driver
(Canon MX860 series CUPS Printer Driver Ver. 10.67.1.0 (03-Aug-2012))
2 Scanner Driver
(Canon MX860 series Scanner Driver Ver. 14.11.4a (03-Aug-2012))
3 Network Tool
(Canon IJ Network Tool Ver. 4.1.0 for Intel Mac (27-Dec-2012)
Canon Software for using advanced printing and scanning functions (while connected to network)
4 Solution Menu
(Canon Solution Menu Ver. 1.4.1 (27-Jul-2012 ))
5 MP Navigator EX
(Canon MP Nav EX Ver. 2.1.3 (02-Auf-2012))
6 Easy-PhotoPrint EX
(Canon Easy-PhotoPrint EX Ver. 4.1.6 (21-Jan-2013 ))
Canon Support (HK) – check your local site
http://www.canon.com.hk/en/download/main/index.do
Select Product and drivers from support site eg http://support-hk.canon-asia.com/
1. Choose a product category
Multifunctional Printers
2. Choose a product series
Pixma
3. Choose a product model
Pixma MX868
4. Choose type of document
Downloads or FAQ
If you have problems installing the software under 10.8, see the FAQ on Canon site. You will need to allow software installs from “unidentified developers by using “Control” Key or by changing your system preferences)
2) Check Canon Printer and Software Working while connected via USB
Once you have downloaded and installed drivers and software and restarted computer, check that the printer and Canon Pixma software (Pixma MP Navigator 2.1 & Photo Print) are working via USB. Open the Canon IJ Network Tool App (Applications / Canon Utilities /IJ Network Tool / Canon IJ Network Tool App) and make sure you can see the Canon MX 860 series (xx.xx.xx.xx.xx.xx) and that it shows the correct SSID Wifi settings (under the Canon IJ Network Tool App ‘Setup menu’). This is normally done as part of the automatic install but worth double checking
3) Add new network printer using ‘apple menu’ / ‘system preferences’ / ‘print and scan’ / “+”).
After you have checked USB printing turn off printer, unplug the USB cable and shutdown the Canon IJ Network Tool App.
Then turn the printer back on and wait 30s. Then add a new printer using ‘apple menu’ / ‘system preferences’ / ‘print and scan’ / “+”). Once you select “+” (add new printer), wait 10-30s for the Wifi Networked Canon MX 860 Series printer to appear in the new window eg Canon MX 860 series (xx.xx.xx.xx.xx.xx) (Kind: “Canon IJ Network”)
DO NOT ADD THE MX 860 SERIES BONJOUR SCANNER (the Bonjour Scanner is the built-in software, is not needed and often appears first on the add printer list). The Canon scanner can be accessed used through the MP Nav EX Ver. 2.1.3 software (which has much better functions)
You will now have two Printer Canon MX860 (USB) and Canon MX860 (Wifi / Network). Set the Canon MX860 (Wifi / Network) as default and test print and scan
If the Wifi Networked Canon MX 860 Series printer does not appear, check the printer and make sure that the printer can see the wifi network. On the printer select Menu / Settings / Device Settings / Lan Settings / WLAN Setting List. It should say WLAN Active, identify the SSID and have an IP address
If the printer can not see the Wifi Network, plug the USB cable back in, then open the Canon IJ Network Tool App (Applications / Canon Utilities /IJ Network Tool / Canon IJ Network Tool App). Make sure you can see the Canon MX 860 series (xx.xx.xx.xx.xx.xx) and that it has your SSID settings (under setup), if it has this info, restart the computer and the printer and try again

Hi, thaks for response, meant to post as a discussion (not question), wanted to save others time if they get the same problem

Just got an ipadmini. screen stuck with usb and itune motiff image?

How to unlock ipadmini screen. Stuck with usb and itune image. Tried to turn off with sleep button and home button. No luck

Your iPad is in recovery mode and you need to restore the device now. Take a look at this kb support article.
http://support.apple.com/kb/ht1808

4s Hotspot tethering only works with USB and BT but not with wifi

Hi,
XP sp3 - iPhone 4s with ios 5.0.1 - on Three one plan
Tethering with wifi works to a friends Samsung phone, wifi on the pc confirmed working with the apple store wifi, tethering with USB and BT works with good connection speeds on my laptop but when i try to tether with wifi it connects to the laptop at 54mbps and all appears well, even claims to have received a small amount of data packets, but no data comes to any browser. The iPhone reports 1 connection to the hotspot and stays connected with a non-pulsing blue bar after the first minute.
In the PC i have tried this http://windows.microsoft.com/en-US/windows7/Change-the-order-of-network-protocol -bindings
I've deleted my firewall (zone alarm) completely and turned off windows firewall to go naked surfing for a second even though they don't cause a problem with USB tethering, makes no difference
I've deleted the network connection numerous times
"repaired" connection
dissabled and enabled the wifi
turned off the wireless with a hardware switch and on again
disabled bluetooth
rebooted many times
reinstalled itunes (latest)
loads more things i can't remember
This is causing me a nightmare. I've been through everything i can find online, been to the Apple store genius bar (genius appeared to have sub zero knowledge / interest as it involved a MS machine), been to a Three shop (legally not allowed to touch my PC apparently) and been to a Sony shop (laptop make, not their fault if my iphone doesn't work). All very frustrating.
Please help if you can! Any suggestion will be tried unless it involves sledge hammers or lakes, and only then for a few more days at most.

Turned off bluetooth on phone, turned off hotspot and on again, phone asked if i wanted to turn on bluetooth or go with USB and wifi only, said usb/wifi only. Still nothing. Rebooted PC and iphone. Turned on hotspot, pc seemlessly connects to network, still no data comes.
One odd thing is zone alarm asks me to "select a security zone for the wireless network at ip address: *******.0" every time and doesn't seem to remember the setting over sessions. When i get the status of the connection the ip address is *****.2 and default gateway is same ********.1 Not sure if that's anything.
Also getting a javascript error about an undefinded component (trustcheckermozilla) since i updated zonealarm but as i said even completely uninstalling zonealarm made no difference. I'll update firefox as well but tried with IE and still no data.

Hi All, can i have some production support issues with rootcasue and resolution for SAP TM?

Hi All, can i have some production support issues with rootcasue and resolution for SAP TM?
Thanks,
Sreenivas

Hi Sreenivas,
I would recommend that you read the Rules of Engagement and other documents in the Getting Started link (top right) before posting anymore. Your Discussion will most likely get reported as non-specific and get removed. If you have a specific problem with TM, please post it in a new thread with error messages, version and SPs installed, and how the error occurs and what you are trying to get TM to do.
There are a lot of resources available in the TM Overview page which can help, so start there and maybe also look at some of the MKS (Monday Knowledge Session) recordings which should also be listed. There are also a lot of experienced people who can help resolve issues your TM installation, but you need to provide enough information on the problems you are having. If you are just looking for information on past problems, do a Search or simply browse through past Discussions which are marked with a green Check (Correct Answer).
Regards, Mike
SAP Customer Experience Group - CEG (and a Moderator)

Can I use HP Pro 8600 with usb and wireless at the same time

Can I use HP Pro 8600 with usb and wireless at the same time? Sometimes I cannot get the wireless to work, it seems to be my laptop. It would be nice if I could use the usb, but it doesn't work. What should / can I do, if anything?
Sam

Hi,
Same physical printer but when connecting to SAME computer using both USB and wireless it becomes two (logical) printers. Probably your default prnter is the wireless one, you have to select the right printer before print .
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

20" Cinema display with USB and firewire ports not working

I have a new 20" display and was wondering why my USB and fire wire ports at the back are not working. I have an external drive that is powered hooked up to the fire wire port and a no powered piano keyboard to a usb port.
Any help please

Verify that the display’s USB and FireWire cables are firmly plugged in to the
computer. Do they show in your profiler?
Try different ports in the computer.
Verify that your computer ports are working with other known problem free device.

Portable HDD with USB and FireWire

Alright, I did a bunch of research and found a bunch of conflicting information. My question to you all is this: are there any good, portable external hard drives that support both FireWire and USB? I have an iMac and an MB Pro, but a lot of people I know don't; I would like to use the FireWire and still be able to use the hard drive with others' computers who do not. I was looking for something that:
did not require an actual electrical plug (wanted the USB/FireWire to be used as the power source)
is at least 1TB (would prefer 1.5TB)
is (preferably but doesn't have to be) rugged
I plan on doing some traveling and whatnot and just throwing it my bag; I'd probably go a while without having a chance to really maintain it, hence my wanting these things.
The main ones I was looking at are the LaCie MiniRugged, LaCie Rugged, Transcend Storejet 25H2P and 25M2, and the Seagate FreeAgent GoFlex. Unfortunately, I've either heard bad reviews or they don't meet all my criteria. The LaCies, for example, were said by some to be outdated, flimsy, etc. (and the mini doesn't have a FireWire port). The Transcends don't do FireWire, nor does the Seagate. In case anyone was wondering, I included the Seagate becaue I have a friend who just got back from a year-long trip bumming around Asia with it and it stood up fine (but, again, no FireWire).
Given all this, I was wondering if anyone could suggest anything. I realize I may not get exactly what I'm looking for, so I'm not going to be super picky. Thanks in advance for any help anyone might be able to offer.

If you can tolerate a somewhat larger enclosure, the OWC Mercury Elite-AL Pro mini has USB, Firewire 800 and eSata connectors. It can be USB powered or with an external adapter. You can get a bare enclosure and install the HDD of your choice or get one with a HDD installed.
I have four of them and I rate them very highly.
Ciao.

Read out from OBD-II Freematic Emulator using ELM327 with USB and LabView

Hello. I have an Freematic OBD-II mk2 emulator which simulates diagnostics of a real car. I have connected an ELM327 diagnostic device with USB cable to the emulator and a PC. The connection between emulator, diagnostic device and computer works. Now I need to read out parameters in LabView. How do I do it? I tried to use the NI VISA functions, but didn't manage to read out anything sensible. How can I for example read out Engine RPM? Do you have some example code?
I want to avoid using Automotive Diagnostic Command Set, because it's to expensive for me.

Oh yes, I didn't realize what this hardware does. Some beginners think that a DB9 is a standard interface for a CAN bus, and when they see the DB9 serial port on their computer they think they can just use that. I was worried this was what you were attempting.
So yes VISA is the right way to go. Once you have this device installed and recognized in Windows it should appear as a COM port. You can open the Windows Device Manager and by plugging and unplugging your device you should see a COM port appear and disappear.
Assuming you do launch LabVIEW and go to the example finder and search for Simple Serial. This is an example VI that can send serial data to a COM port, wait, then read the response. It can basically work like hyperterminal. Assuming there are no already made LabVIEW drivers (I haven't seen any) this will be a good place to start. Using documentation on your hardware you can start to come up with commands to do things like read and write CAN data, by sending the appropriate commands to the hardware over serial.
http://www.elmelectronics.com/obdic.html
Depending on what you want to do it might be a decent amount of work. Of course if you do get anything good and working feel free to post your progress here so others can benefit.
Unofficial Forum Rules and Guidelines - Hooovahh - LabVIEW Overlord
If 10 out of 10 experts in any field say something is bad, you should probably take their opinion seriously.

Every since I got my iphone4 out of recovery mode (stuck on screen with usb and itunes), now everytime i plug up my iphone to computer it asks me to restore (i did several times) but that all its doing, its not even giving me the option to sync my music

every since i got my iphone out of recovery mode (stuck on screen with itunes and usb cord) by restoring it, NOW every time i plug my iphone it only asks me to restore my iphone (i did this several times). It will not even give me the option to sync my music back...this is extremely frustrating. Please help

so i cant sync music or apps HELP

Simultaneous capture with usb and gige cameras ?

Hi,
I am unable to capture (continuously) simultaneously from a USB and a GigE camera, is there a limitation in Labview ? Both cameras work if I use them one at a time. I am using Labview 2012. Both cameras are IMAQdx devices and I am using IMAQdx VIs.
Thanks,
Best,
Saumil

I have just converted to low level, just in case. Not tested yet...
USB camera: USB 2.0, 10 frames/sec, 1280x1024 -> about 13 MBytes/sec
GigE camera: 300 frames/sec, 640x480 -> about 90 MBytes/sec
So both cameras data rates are within their respective interface limits. Although when I started to archive raw frames from the USB camera, everything in labview became super slow. The slowness was reduced dramatically once I started storing to compressed AVI files (rates went from 15 Mbytes to approx. 1.5 Mbytes/sec). I have not tested archival with the GigE camera yet, I am expecting troubles, just dont know how severe.
Thanks for your help,
Saumil

Lacie Extreme mounts with USB and FW800 but not FW400

Shows as USB and FW800 only on Powerbook G4 1.67 15" 10.4.9 2Gb
I'm not being dismissive but I have explored all obvious options;
Drive mounts OK FW400 on another Mac with the same cable.
Shows in System Profiler on all three interfaces on other Mac.
FW CD writer exhibits identical symtoms.
Any ideas please?
Cheers

Hi,
I've just bought a brand new LaCie rugged 80GB USB 2.0 hard drive. It came with 2 cables. One for power from the powerbook and the other to transer data. The manual said "no drivers or installation is required. The drive should mount in a few seconds after plugging it in." 3 attempts - LaCie just doesn't mount. I have no idea what to do. Please HELP!!
Thanks
Powerbook G4 Aluminium Mac OS X (10.4.10) 1GB Ram

Phones that support video with MMAPI (and ideally: UMTS)?

Hi there,
does anybody know which phones do currently support playing back video (and ideally: streaming video) with the MMAPI? At the moment, I know the Nokia 3650 supports it...
More interesting: are there any phones that do support UMTS and playing back video with the MMAPI? At the moment, I have a Nokia 7600 sitting in front of me and I'm still kind of shocked since it tells me it won't play videos and not even AMR soundfiles (only supported content types on this phone: audio/x-tone-seq, audio/midi, audio/sp-midi).
The tragic thing about this is that the phone does have a media player - I just can't access it via the MMAPI and therefore, I can't access it via Java at all... :-(
kind regards,
david

Hi,
Your requirements are covered in Sony Ericsson Z1010 phone, which will be released in the market soon.
/Thilak

CMOS camera with USB and labview

Hi,
I'm looking for an USB camera with a CMOS sensor that I can use with
Labview. Preferable with Labview drivers and low cost.
The size of the image may be VGA or 1.3Mpixels. I need to have full control
with labview and saving RAW images.
Is there anybody who can recommend me such a camera?
Thanks!

I have a solution,we can call Mirco CMOS sensors DLL and OVT sensor DLL then you can writing register freely, but you need to design the hardware or buy it.
my [email protected]

Support forCamcorders with USB and no fire wire.

Similar Messages

Maybe you are looking for