Supported access points for the rv220w

I need to extend my wireless coverage to another building. What access points, in repeater mode, will the rv220w support? I need an AP with detachable antennas. I have an external mounted antenna on the metal building that I need to hook the AP to. Thanks!

Hi R. B, thank you for using our forum, my name is Luis I am part of the Small business Support community. As far I know the RV120W and the RV220W uses the same chipsets, so they could be used for WDS bridge setup.
For your second point the RV120W has antennas and you could remove them. Bellow you will see the review of the RV120W.
http://www.cisco.com/en/US/prod/collateral/routers/ps9923/ps10852/DS_C78-590161-00.html
I hope you find this answer useful
Greetings,
Luis Arias.
Cisco Network Support Engineer.

Similar Messages

Can I use the Ethernet Port for a computer when it is also used as a wireless network with an Airport Extreme as the access point for the wireless network

Can I use the Ethernet Port of the A1264 Airport Express to connect to the Ethernet port of a computer that does not have wireless capability when the Airport Express is also used on a wireless network with an Airport Extreme 5th generation as the access point for the network?
I have AE 5th gen
looking to buy (from ebay) the AEX A1264
Various computers, printers and hubs for the network
Is this possible to do?

Bob, Thanks for the info. I have read different articles that said yes, but I wanted to make sure before I commit to buy. I have an older A1084 which I could not use the Ethernet port. I know at one point I was able to when I was on 10.4. Now that I am on an Intel processor and 10.8 I am going to have to upgrade some of my Apple wireless hardware.
Thanks Again.

Using Mac mini as an access point for home network

Hi
I'm looking for some help on using my mac mini as an access point on my home network.
I have a G5 tower which is wired in to my router and acts as a home server. It has all my itunes library, films, etc
I stream these to various machines in the house, one of which is a mac mini in our living room.
The mini is connected to the network via powerline adapters meaning the airport is left free.
So i set up internet sharing on the mini via airport so I can use the machine as an access point for the living room.
If I connect another machine to the mini via airport, Internet is working fine but for some reason I can't see the any other machines on the network.
All I see in the sidebar is the mini, not the server.
I've tried it on both mine and my friends macbook but had no luck.
Am I doing this the wrong way?
How would you go about doing this?
Cheers

Internet Sharing may not be providing an address via DHCP, It also may not be providing a subnet Mask that can get you to communicate with the other computers on your local Network.
Take a look at what IP addresses are being used by the various computers on the network. I would expect you have a Router that may be using 192.168.0.1 as its base "private" address, and issuing DHCP Addresses in that range and higher with a subnet mask of 255.255.255.0, meaning anything with the same three high octets can communicate freely without Router intervention.
But what addresses are bing used for the Wireless Shared computer(s)? and what subnet mask?

Do we have any third party FLEX component libraries to support accessibility feature for all the components(like: ViewStack, ToggleButtonBar, charts and etc..) ?

I am working on FLEX 4.6 SDK it provides 35 components with built in accessibility support. My Application contains some components which have no built in accessibility support but I need to provide accessibility support for those components too. I have gone through the Flex docs to customize the non accessible components to support accessibility feature, But the docs where not clear. To customize a single component I have to overwrite lot of code in SDK level.
and it takes lot of effort.
So, I would like to use FLEX component libraries which provides accessibility support for all the component.
Could you please guide me how can I provide accessibility support for other components with out putting more effort on it.
Thanks in advance...

There is already such thing in myfaces called "security context" [1]. You could find build of sandbox.jar [2]
[1] http://myfaces.apache.org/sandbox/securityContext.html
[2] http://people.apache.org/builds/myfaces/nightly/

Some Question About Access point of the WRT54G

How many devices can the access point of the WRT 54G support?
I am looking at hooking up one Wii, 2 laptops and a Nintendo DS will this WRT 54G be able to handle that or will I need other devices.

Not sure how many wireless devices the WRT54G can handle. Most AP's depending on the amount of traffic is around 30 or so. Here is a link to the web site with the info for the WRT54G.
http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1149562300349&...
Richard Aichner (Ikester)

How many clients support access points 1602, 2602, 3602?

Hi! How many clients support access point 1602, 2602, 3602. I have found for example that the 1602 supports 32 ClientLink clients and max 128 clients, APs 2602, 3602 supports 128 ClientLink clients and max 200 clients. But is it really? And can we say for example that the AP 2602 will withstand max 200 clients?

The reason the answer varies so much, is because there are so many variables (this is also why the value ranges so much from one manufacture to the next). When determining the answer you are looking for you need to consider the following factors and likely more:
AP model and the features it supports
single, dual, or tri radio AP
20, 40, or 80Mhz wide channels
Device type (b/g, b/g/n, a/b/g/n, a/b/g/n/ac, spatial stream support, and channel width support)
Security/QOS method(s) employed
Average distance from the AP
Obstructions between devices and radios
Number of competing radios for the same channel
Data rates configuration
Rogue detection/mitigation configuration
Surrounding client density not just the area of concern client density
Noise floor levels
Application types/per user network load (is it heavy like YouTube traffic or a drone on the network like Pandora)
Network latency on the switching side - including the internet circuit
Application of per SSID, per user, and or per application rate limiting
The list continues, but I think you get the idea
I have personally seen 80 devices on a 5Ghz radio of a 3500 access point with several other access points and at least 200 other clients in the area and it was working well. That being said I would never design to expect that many on a single radio, but I think it is better said that you can safely design for 20-30 clients per 2.4Ghz radio and 25-40 clients per 5Ghz radio.
The default statement of 20-25 per AP and similar low expectation statements concerning Cisco wireless have been around for many years. It is now 2014. About 65% of clients support 5Ghz, ~9% support AC (already), ~90% support some form of N, and ~0.01% support B only. The landscape of wireless is changing fast making questions like this one have ever changing answers.
I hope this helps :).
John

Can i set up an access password for the ipod on my ipad 2?

I purchased an Ipad 2 for my son to use in his therapy for autism. He knows how to use it and knows that we have purchased shows and movies for him to watch in the car. Well now that is all he wants to do. I am wondering if there is a way that I can set up a password to access the ipod. If he cant get into the ipod to see shows and movies he will be fine with just playing the games we have for his therapy. I have looked online and have not had much luck finding an answer to this question. So again can someone please tell me if there is a way to set up an access password for the ipod on the ipad2??????

Have you got Home Sharing set up (http://support.apple.com/kb/HT3819) ? i.e. he may be viewing the content from your computer, not on the actual iPad. If that is the case (which would explain to me him being able to access the videos via the iPod app), then the Restrictions settings that I've already mentioned should also work on that 'remote' content.
Edit : your last reply appeared whilst I was typing/checking this. And no, the Videos/iPod apps can't be passcode protected, you will need to go back into Restrictions and remove the restriction, or if the films are only on your computer and not on the iPad itself you could turn off home sharing on the iPad whilst he's playing the games : Settings > iPod and tap on your account id and/or password on the right under Home Sharing and delete it/ them (re-enter them when you want to re-enable it).
Message was edited by: King_Penguin

Is there any way I can control which specific access point I connect (and stay connected) to from amongst a set of access points with the same SSID?

I'm working from a boat in a harbor in which the ISP has deployed numerous access points around the periphery. All the access points share the same SSID and each is configured to use either channel 1, 6 or 11. From my location, there are over a dozen of these access points "visible" (based on the the output of WiFi Scanner) with a range of RSSI and S/N values that vary over time.
The ISP has told me that the quality of my connection should be "perfectly fine" for any access point with an RSSI value better than -75, but I know from experience that my connection quality is miserable (i.e. < 50Kbps download) for almost all of these, including those with RSSI values better than -75. There is at least one exception, however, which gives me on the order of 2Mbps download, which is "great" in this context.
I've tried using a more powerful USB antenna plugged into my MacBook Air (mid 2011), but as far as I can tell, it really doesn't make much difference. Neither does my location within the boat. The overriding factor seems to be which access point I happen to connect up to.
I should point out that the closest access points are about 75 yards away, with many of them being several hundred yards away or more. I'm guessing that even though the signal strength of some of the distant access points is causing them to get "chosen" some times, the results are unacceptable due to the distance.
I'm hoping that I can determine, through experimentation, which access point(s) provide(s) acceptable performance and then configure my Mac to limit my connection to those points through whatever mechanism I need to use (e.g. channel, MAC id, etc.).

Establishing a wireless connection with a client computer is left to the access point for various reasons. One reason that your Mac may not connect to the strongest access point is that it may have reached a limit of the number of clients it can serve, leaving it unable to accept a connection with another. The limit may not be very large.
Suppose that happens, and your Mac establishes a connection with a more distant access point having a weaker signal. Then, suppose a client drops off the network. Doesn't this mean your Mac will switch to the stronger access point? Not necessarily. The throughput delivered to and from your Mac would have to drop below a threshold specified in the AP for it to drop the client, leaving your Mac free to connect with another one. The reason for this is to prevent rapid switching from one AP to another in an area in which two signals are of approximately equal quality. If that were to occur the frequent and repetitive handshaking between the two devices would slow throughput to zero.
In an environment in which several access points are broadcasting the same SSID, Apple provides no insight as to how it determines which access point to choose. This is the reason I suspect this "choice" is a function of the router, or access point. The connection originates with it, not the Mac.
Now, what would solve your dilemma would be to determine a way to control the access point with which your Mac connects, by specifying the access point's unique MAC address for example. In this happy circumstance, you could maintain an editable "whitelist" or "blacklist" of the harbor's access points and be able to choose which among them you prefer.
I do not believe OS X maintains such a record of MAC addresses though, only those of the routers it uses. If I am correct about that, such a solution is unlikely to exist. Don't let that discourage you from searching for one though... I would concentrate on something like "selecting access point by specific MAC address".
I did find this patent application though:
Roaming Network Stations Using A Mac Address Identifier To Select New Access Point
Perhaps it's a start

[HELP] Error: "JDBC theme based FOI support is disabled for the given data"

Hi all,
I have already set up MapViewer version 10.1.3.3 on BISE1 10g OC4J server. I am current using JDK 1.6. I create a mvdemo/mvdemo user for demo data.
The MapViewer demo is running fine with some demo without CHART. But give this error with some maps that have CHART like: "Dynamic theme, BI data and Pie chart style", "Dynamic theme and dynamic Bar chart style". The error is:
----------ERROR------------
Cannot process the FOI response from MapViewer server. Server message is: <?xml version=\"1.0\" encoding=\"UTF-8\" ?> <oms_error> MAPVIEWER-06009: Error processing an FOI request.\nRoot cause:FOIServlet:MAPVIEWER-06016: JDBC theme based FOI support is disabled for the given data source. [mvdemo]</oms_error>.
----------END ERROR------
I searched many threads on this forum, some point me to have this allow_jdbc_theme_based_foi="true" in mapViewerConfig.xml and restart MapViewer.
<map_data_source name="mvdemo"
jdbc_host="localhost"
jdbc_sid="bise1db"
jdbc_port="1521"
jdbc_user="mvdemo"
jdbc_password="mvdemo"
jdbc_mode="thin"
number_of_mappers="3"
allow_jdbc_theme_based_foi="true"
/>
Error Images: [http://i264.photobucket.com/albums/ii176/necrombi/misc/jdbcerror.png|http://i264.photobucket.com/albums/ii176/necrombi/misc/jdbcerror.png]
I have this configuration, but no luck. Could anyone show me how to resolve this problem?
Rgds,
Dung Nguyen

Oop, i managed to have this prob resolved!
My prob may come from this I use both scott and mvdemo schema for keeping demo data (import demo data).
Steps i made to resolve my prob are:
1) Undeploy MapViewer from Application Server Control (http://localhost:9704/em in my case)
2) Drop user mvdemo
3) Download mapviewer kit from Oracle Fusion Middleware MapViewer & Map Builder Version 11.1.1.2
4) Deploy MapViewer again
5) Recreate mvdemo and import demo data
6) Run mcsdefinition.sql, mvdemo.sql with mvdemo user (granted dba already)
7) Edit mapViewerConfig.xml
<map_data_source name="mvdemo"
jdbc_host="dungnguyen-pc"
jdbc_sid="bise1db"
jdbc_port="1521"
jdbc_user="mvdemo"
jdbc_password="!mvdemo"
jdbc_mode="thin"
number_of_mappers="3"
allow_jdbc_theme_based_foi="true"
/>
Save & Restart MapViewer
And now, all demos run fine. Hope this helpful for who meet prob like my case.

Can I use this as a wireless access point for my network

can I use this as a wireless access point for my network

umm... use what?
A Time Capsule? Sure. It's just like many other wireless base stations. It can run in either bridge or route mode - in bridge mode it's just like an access point linking the wired and wireless networks together.

Satellite L350 - Access code for the router

Dear Sirs
I have a Toshiba Satellite L350 running Windows 7 Ultimate. For the first 5 months it remembered the wireless access code for the router. I then installed a BT Home Hub which I subsequently removed and from then on the Windows 7 machine will no longer remember the password.
I have spent hours on the phone with Microsoft to no avail. Can anyone help?

The problem is very simple but the solution is not.
As I said earlier the computer remebered the wirless access code for around 5 months.
I then installed a BT home hub (free from BT) and it worked fine and then I uninstalled it and reverted back to my D-Link router.
From this point on every time I turn on the computer I have to enter the wireless access code to connect to the internet and until I turn off the computer all works fine.
Microsoft have not been able to locate the problem and neither have BT hence this last attempt to try and find the solution.
Thanks for your reply and I look forward to some help.

I cannot print to a p1102w if i am on a machine connected to the same access point as the printer..

I have two p1102w printers set up in a school, any time I try to print it will only work if the laptop i'm using is connected to a different wireless access point than the printer. This happens anywhere in the school, has anyone ever encountered something like this before?
The laotops are running xp sp3 professional by the way.
Thanks in advance for your thoughts and ideas.
joray75

First thing to do is check your routing rules and tables in the network to make sure the type of communication you're wanting (printing via wireless on the same access point) is allowed. I'm betting something is off in those that's preventing communication.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

SSRS 2008 Column Chart with Calculated Series (moving average) "formula error - there are not enough data points for the period" error

I have a simple column chart grouping on 1 value on the category axis. For simplicity's sake, we are plotting $ amounts grouping by Month on the category axis. I right click on the data series and choose "Add calculated series...". I choose moving average. I want to move the average over at least 2 periods.
When I run the report, I get the error "Formula error - there are not enough data points for the period". The way the report is, I never have a guaranteed number of categories (there could be one or there could be 5). When there is 2 or more, the chart renders fine, however, when there is only 1 value, instead of suppressing the moving average line, I get that error and the chart shows nothing.
I don't think this is entirely acceptable for our end users. At a minimum, I would think the moving average line would be suppressed instead of hiding the entire chart. Does anyone know of any workarounds or do I have to enter another ms. connect bug/design consideration.
Thank you,
Dan

I was having the same error while trying to plot a moving average across 7 days. The work around I found was rather simple.
If you right click your report in the solution explorer and select "View Code" it will give you the underlying XML of the report. Find the entry for the value of your calculated series and enter a formula to dynamically create your periods.
<ChartFormulaParameter Name="Period">
<Value>=IIf(Count(Fields!Calls.Value) >= 7 ,7, (Count(Fields!Calls.Value)))</Value>
</ChartFormulaParameter>
What I'm doing here is getting the row count of records returned in the chart. If the returned rows are greater than or equal to 7 (The amount of days I want the average) it will set the points to 7. If not, it will set the number to the amount of returned rows. So far this has worked great. I'm probably going to add more code to handle no records returned although in my case that shouldn't happen but, you never know.
A side note:
If you open the calculated series properties in the designer, you will notice the number of periods is set to "0". If you change this it will overwrite your custom formula in the XML.

How to create the Access sequence for the Vendor+material+plant combination

Hi all
Please let me know How to create the Access sequence for the Vendormaterialplant combination..
Whats the use? What its effect in purhcase and taxe..
brief me please

Hi,
you are asked to maintain the access sequence for the tax condition for which you are putting 7.5%.
goto OBQ1 or img..financial accounting new...global settings.... taxes on sales and purchases ......basic settings.....
find the tax condition type. see in it which access sequence is attached.
if there is none then use JTAX used for taxes in India.
or you can create the similar one for your.
to create the same goto OBQ2.
new entry or copy JTAX.
and assign the access sequence to condition type.
this will resolve your problem if you just need to assign the access sequence.
regards,
Adwait Bachuwar

When I download itunes, it says that Ipod Service failed to start. I checked the services under task manager and when I try to start it, it says access denied. How to I get access and for the ipod service to start and run?

Please help. My ipod classic could not be recognised by itunes when I connect my ipod to PC. Previously it has been recognised before I updated. This was a while ago now and so I removed all apple files and re installed the latest itunes but am having the same problem.
When I download itunes, it says that Ipod Service failed to start. I checked the services under task manager and when I try to start it, it says access denied. How to I get access and for the ipod service to start and run?

Some anti-virus programs (e.g., McAfee) have this rule that can be invoked under the "maximum protection" settings: PREVENT PROGRAMS REGISTERING AS A SERVICE. If that rule is set to BLOCK, then any attempt to install or upgrade iTunes will fail with an "iPod service failed to start" message.
If you are getting this problem with iTunes, check to see if your anti-virus has this setting and unset it, at least for as long as the iTunes install requires. Exactly how to find the rule and turn it on and off will vary, depending upon your anti-malware software. However, if your anti-virus or anti-malware software produces a log of its activities, examining the log may help you find the problem.
For example, here's the log entry for McAfee:
9/23/2009 3:18:45 PM Blocked by Access Protection rule NT AUTHORITY\SYSTEM C:\WINDOWS\system32\services.exe \REGISTRY\MACHINE\SYSTEM\ControlSet001\Services\iPod Service Common Maximum Protection:Prevent programs registering as a service Action blocked : Create
Note that the log says "Common Maximum Protection: Prevent programs registering as a service". The "Common Maximum Protection" is the location of the rule, "Prevent programs registering as a service" is the rule. I used that information to track down the location in the McAfee VirusScan Console where I could turn the rule off.
After I made the change, iTunes installed without complaint.

Supported access points for the rv220w

Similar Messages

Maybe you are looking for