Suppress deployment wizard in remote site mdt 2013

i am getting deployment wizard (welcome screen) even my bootstrap.ini has SkipBDDWelcome=YES.
so i had created mdtdeployment$ share and give all necessary permission. create link in deploymentworkbench to remote share and replicate content.
when i am booting with flash drive, it connects with remote server fine because i ping server and gather.log file has rootdeploy to remote server. but i can't get rid of this welcome screen...any help thanks...
orion

You need to update the deployment share, and replace the MDT boot image in WDS after making changes to bootstrap.ini (Note: Editing customsettings.ini for this setting is not needed).
Also, offline media (flash drive) has it's own bootstrap.ini, separate from the one in the normal deployment share.
/ Johan
Regards / Johan Arwidmark Twitter: @jarwidmark Blog: http://www.deploymentresearch.com FB: www.facebook.com/deploymentresearch

Similar Messages

Best Practice for SRST deployment at a remote site

What is the best practice for a SRST deployment at a remote site? Should a separate router such as a 3800 series be deployed for telephony in addition to another router to be deployed for Data? Is there a need for 2 different devices?

Hi Brian,
This is typically done all on one ISR Router at the remote site :)There are two flavors of SRST. Here is the feature comparison;
SRST Fallback
This feature enables routers to provide call-handling support for Cisco Unified IP phones if they lose connection to remote primary, secondary, or tertiary Cisco Unified Communications Manager installations or if the WAN connection is down. When Cisco Unified SRST functionality is provided by Cisco Unified CME, provisioning of phones is automatic and most Cisco Unified CME features are available to the phones during periods of fallback, including hunt-groups, call park and access to Cisco Unity voice messaging services using SCCP protocol. The benefit is that Cisco Unified Communications Manager users will gain access to more features during fallback ****without any additional licensing costs.
Comparison of Cisco Unified SRST and
Cisco Unified CME in SRST Fallback Mode
Cisco Unified CME in SRST Fallback Mode
â¢ First supported with Cisco Unified CME 4.0: Cisco IOS Software 12.4(9)T
â¢ IP phones re-home to Cisco Unified CME if Cisco Unified Communications Manager fails. CME in SRST allows IP phones to access some advanced Cisco Unified CME telephony features not supported in traditional SRST
â¢ Support for up to 240 phones
â¢ No support for Cisco VG248 48-Port Analog Phone Gateway registration during fallback
â¢ Lack of support for alias command
â¢ Support for Cisco UnityÂ® unified messaging at remote sites (Distributed Exchange or Domino)
â¢ Support for features such as Pickup Groups, Hunt Groups, Basic Automatic Call Distributor (BACD), Call Park, softkey templates, and paging
â¢ Support for Cisco IP Communicator 2.0 with Cisco Unified Video Advantage 2.0 on same computer
â¢ No support for secure voice in SRST mode
â¢ More complex configuration required
â¢ Support for digital signal processor (DSP)-based hardware conferencing
â¢ E-911 support with per-phone emergency response location (ERL) assignment for IP phones (Cisco Unified CME 4.1 only)
Cisco Unified SRST
â¢ Supported since Cisco Unified SRST 2.0 with Cisco IOS Software 12.2(8)T5
â¢ IP phones re-home to SRST router if Cisco Unified Communications Manager fails. SRST allows IP phones to have basic telephony features
â¢ Support for up to 720 phones
â¢ Support for Cisco VG248 registration during fallback
â¢ Support for alias command
â¢ Lack of support for features such as Pickup Groups, Hunt Groups, Call Park, and BACD
â¢ No support for Cisco IP Communicator 2.0 with Cisco Unified Video Advantage 2.0
â¢ Support for secure voice during SRST fallback
â¢ Simple, one-time configuration for SRST fallback service
â¢ No per-phone emergency response location (ERL) assignment for SCCP Phones (E911 is a new feature supported in SRST 4.1)
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/vcallcon/ps2169/prod_qas0900aecd8028d113.html
These SRST hardware based restrictions are very similar to the number of supported phones with CME. Here is the actual breakdown;
Cisco 880 SRST Series Integrated Services Router
Up to 4 phones
Cisco 1861 Integrated Services Router
Up to 8 phones
Cisco 2801 Integrated Services Router
Up to 25 phones
Cisco 2811 Integrated Services Router
Up to 35 phones
Cisco 2821 Integrated Services Router
Up to 50 phones
Cisco 2851 Integrated Services Router
Up to 100 phones
Cisco 3825 Integrated Services Router
Up to 350 phones
Cisco CatalystÂ® 6500 Series Communications Media Module (CMM)
Up to 480 phones
Cisco 3845 Integrated Services Router
Up to 730 phones
*The number of phones supported by SRST have been changed to multiples of 5 starting with Cisco IOS Software Release 12.4(15)T3.
From this excellent doc;
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/vcallcon/ps2169/data_sheet_c78-485221.html
Hope this helps!
Rob

Sharepiont Content Deployment Wizard not working on SP 2013

Hi, I was wondering if someone else has come across this issue. I was trying to use the SharePoint Content Deployment Wizard on SharePoint 2013. However, when I launch the product, I receive the following error: "SpContentDeployment
Wizard has stopped working". Is there anything i can do in this case to get the sofware to work in my environment? Here is the output from the details section:
Description:
Stopped working
Problem signature:
Problem Event Name: CLR20r3
Problem Signature 01: spcontentdeploymentwizard.exe
Problem Signature 02: 4.0.1.0
Problem Signature 03: 4ba7fc57
Problem Signature 04: SPContentDeploymentWizard
Problem Signature 05: 4.0.1.0
Problem Signature 06: 4ba7fc57
Problem Signature 07: f7
Problem Signature 08: f1
Problem Signature 09: System.IO.FileNotFoundException
OS Version: 6.2.9200.2.0.0.272.7
Locale ID: 4105
Read our privacy statement online:
http://go.microsoft.com/fwlink/?linkid=190175
If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt
thanks,
Sherazad

Hi,
You can download the source code from codeplex, then build the solution.
If the issue still exists, you can debug the source code or you can post the issue to the
ISSUES, you will get more help and confirmed answers from there.
http://spdeploymentwizard.codeplex.com/workitem/list/basic
Best Regards
Dennis Guo
TechNet Community Support

Deployed a new computer with MDT 2013, but Windows licensing did not give me an initial grace period

Hi all,
Strange issue. I have created a Windows 7 x64 gold image to be deployed. When creating the image, I allowed Sysprep to rearm Windows. I've deployed about 10 computers in the past week and everything has worked fine.
Yesterday, I deployed another two computers. One works fine, but when I logged into the second one, I was greeted with the you need to activate Windows now screen. I was confused so I ran slmgr /dlv and sure enough my license status was not "Initial
Grace Period" but instead "Notification." (by the way, it did show remaining rearms as 2, which is expected since it was rearmed with sysprep when capturing the image, so we know it was in fact rearmed).
So my question is how and why did this happen? I was in a hurry so I just ran slmgr /rearm to burn off another rearm. I plan on putting in a KMS server at the end of the week, but I'm worried if I should redeploy the image to this machine since something
appears to be wacky.
Anyone seen this before or have any thoughts on the matter?

Either way, it was correct when I checked it today so maybe it corrected itself after Windows was installed? Not sure how else to explain this one.
Me either.
After Windows is installed, if you are domain-joining, the clock will sync to your Domain Controller.
If not domain-joined, Windows will try to sync to time.windows.com (or similar).
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

MDT 2013 - Litetouch deployment failed, Return Code = -2147467259 0x80004005

I'm attempting to deploy an image that I have recently captured with MDT. I was able to capture the image without any problems and after capturing, it booted up properly. But now when I go to deploy the image using a Standard Task Sequence it
errors out. It does boot into WinPE and gets to the installing operating system portion then spits out the following 8 errors:
(5624):2: Run ImageX: /apply "\\PDC31089\DeploymentShare$\Operating Systems\Win7_BUP_1-31-14\Win7_BUP_1-31-14.wim" 1 C:
Litetouch deployment failed, Return Code = -2147467259 0x80004005
Failed to run the action: Install Operating System.
Unknown error (Error: 000015F8; Source: Unknown)
The execution of the group (Install) has failed and the execution has been aborted. An action failed.
Operation aborted (Error: 80004004; Source: Windows)
Failed to run the last action: Install Operating System. Execution of task sequence failed.
Unknown error (Error: 000015F8; Source: Unknown)
Task Sequence Engine failed! Code: enExecutionFail
Task sequence execution failed with error code 80004005
Error Task Sequence Manager failed to execute task sequence. Code 0x80004005After I receive the error messages if I attempt to restart the computer and allow it to boot up it just comes up with:"An operating system wasn't found. Try disconnecting any drives that don't contain an operating system"
I have tried the following to resolve this issue:
Create a new deployment share with only network drivers added and the one .WIM that was captured with MDT as well as one Task sequence.
Update to MDT 2013
Update Deployment share and completely regenerate Boot images
Tried starting deployment from within Windows by mapping the drive and executing litetouch.vbs
Also tried starting deployment using USB boot disk
I'm running out of ideas and seem to keep getting the same 8 error messages. It's very aggravating and am hoping that someone can point me in the right direction.
I've included some log files on Skydrive at: https://skydrive.live.com/redir?resid=6375A8F9E8089918%21105

I came across this post recently. I am having the same string of errors suddenly when I try to deploy any image from my MDT 2013 server now. Previous images now fail to install soon after the Inject Drivers task sequence at the Install Operating System sequence.
Each time I try to deploy an image(have tried several each with different task sequences), I get the same 7 errors.
The errors produced are:
Litetouch deployment failed, Return Code = -2147467259 0x80004005
Failed to run the action: Install Operating System.
Incorrect Function (Error: 00000001; Source: Windows)
The execution of the group (Install) has failed and the execution has been
aborted. An action failed.
Operation aborted (Error: 80004004; Source: Windows)
Failed to run the last action: Install Operating System. Execution of task
sequence failed.
Incorrect Function
(Error: 00000001;
Source: Windows)
Task Sequence Engine failed! Code: enExecutionFail
Task sequence execution failed with error code 80004005
Error Task Sequence Manager failed to execute task sequence. Code 0x80004005
My HD size is 146GB with about 71GB being free.
The BDD.log file is too large to post here apparently. Here are the
last bits of it.
<![LOG[Assume this disk is the destination Disk, and verify.]LOG]!><time="11:36:58.000+000" date="09-26-2014" component="ZTIDiskpart"
context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[TargetPartitionIdentifier is set, find disk: SELECT * FROM Win32_LogicalDisk WHERE Size = '499577253888' and VolumeName = 'OSDisk' and VolumeSerialNumber = 'CA3BC8A9']LOG]!><time="11:36:58.000+000" date="09-26-2014"
component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[Search for Drive: TargetPartitionIdentifier SELECT * FROM Win32_LogicalDisk WHERE Size = '499577253888' and VolumeName = 'OSDisk' and VolumeSerialNumber = 'CA3BC8A9']LOG]!><time="11:36:58.000+000" date="09-26-2014"
component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[Found Drive: C:]LOG]!><time="11:36:58.000+000" date="09-26-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[Property OSDTargetDriveCache is now = C:]LOG]!><time="11:36:58.000+000" date="09-26-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[Property OSDisk is now = C:]LOG]!><time="11:36:58.000+000" date="09-26-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[Target Drive Letter Found: C:]LOG]!><time="11:36:58.000+000" date="09-26-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[Found OS Drive: C 0]LOG]!><time="11:36:58.000+000" date="09-26-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[New ZTIDiskPartition : \\MININT-I3DUVLI\root\cimv2:Win32_LogicalDisk.DeviceID="C:" \\MININT-I3DUVLI\root\cimv2:Win32_DiskPartition.DeviceID="Disk #0, Partition #1"]LOG]!><time="11:36:58.000+000"
date="09-26-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[Check Disk [0] <> [0] OK to skip.]LOG]!><time="11:36:58.000+000" date="09-26-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[####### NOTE: If this is one of the last lines in your BDD.log file, check C: for the most up to date bdd.log!!!]LOG]!><time="11:36:58.000+000" date="09-26-2014" component="ZTIDiskpart"
context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[ZTIDiskpart processing completed successfully.]LOG]!><time="11:36:58.000+000" date="09-26-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[Event 41001 sent: ZTIDiskpart processing completed successfully.]LOG]!><time="11:36:58.000+000" date="09-26-2014" component="ZTIDiskpart" context="" type="1" thread=""
file="ZTIDiskpart">

MDT Deployment Wizard doesn't start after booting from the LiteTouchPE.iso

Hello Experts,
I'm using the MDT 2013. When I boot the Physical machine or VM with the LiteTouchPEx86 or x64, I'm not getting the Deployment Wizard. It just stops with a command prompt X:\Windows\System32>. Anyone faced this problem earlier. I searched the Technet, but
I couldn't find any solutions.
I've done all the possible things which I know. Please help.
Regards,
Sukumar. R.

You are getting some kind of crash, or your variables are not setup correctly.
From the command prompt (X:\Windows\System32 ) Run the following command and let us know what the error message is (exactly):
cscript x:\deploy\scripts\litetouch.wsf /debug:true /debugcapture
It should crash or exit with error error. If it does not crash with a specific line number, then please copy the bdd.log file to a public site like OneDrive and copy the link here.
Keith Garner - Principal Consultant [owner] -
http://DeploymentLive.com

KeyboardLocale and SystemLocale during UDI Wizard (MDT 2013)

Hi
We're using SCCM 2012 R2 integrated with MDT 2013
we deploy Windows 7 with Task Sequence process with UDI Wizard
we have 2 main problems regarding the Language Settings
1. in the wizard we define UserLocale, KeyboardLocale and UILanguage, OSDTimeZone
what about SystemLocale ? which is very basic to set, but there is no built-in combobox for it.
the only workaround I can come up with is to build a custom page with that setting but it is hard to create a combobox with all the available languages, even when editing the XML directly and not via the UI.
2. if I set the KeyboardLocale to Hebrew for example in the Wizard, the SMS environment variable is set to 0409:0000040d
this causes the deployment to end with Hebrew installed with US keyboard layout. which is wrong!
I expect the value to be 040d:0000040d (Hebrew keyboard with Hebrew layout)
which brings me to another question... how can I define multi keyboards? because my actual goal is to have English as my default keyboard language and to have Hebrew as a secondary keyboard.
it is not Hebrew in particular. we deploy Windows in 20 different sites worldwide and English should be always be the default language and we want to add another local additional language
I added a script that modifies the keyboardlocale and converts it from 0409:00000### to 0409:00000409;0###:00000###, but I feel like it is too much for this little setting that should be so basic...
any help will be appreciated. thanks
Tamir Levy

Hi,
Here is video for your reference.
Configuring MDT 2012 UDI Replace Computer Scenario
http://technet.microsoft.com/en-us/video/configuring-mdt-2012-udi-replace-computer-scenario
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

MDT 2013 - A Connection to the deployment share could not be made - DHCP Lease was not obtained

First, let me give you some context:
Framework: MDT 2013 with MS SDK 7.1
Task Sequence: Standard Client TS with sysprep and capture.
Target workstation (build workstation): VM Guest on ESX 5.5 host, 8 vCPU, 8GB RAM, LSI Logic SAS Controller, E1000 NIC, SSD DAS
Behavior: The VM loads and installs the OS fine in PE, VM boots into OS successfully and resumes the TS, after the first system reboot, the error message occurs and it reads:
A connection to the deployment share (\\*********\DeploymentShare$) could not be made. DHCP Lease was not obtained for any Networking device! Possible Cause: Check physical connection. Retry:...... Cancel:.....
While observing this error, I didn't notice the NIC hadn't completely initialized and obtained an IP yet (network adapter icon in systray), additionally hitting retry after the NIC was initialized resumed the TS.
This behavior reoccurs with several subsequent reboots until a few more applications (Citrix Receiver, VMware Tools) with services are installed which seem to then slow the system boot-up time and then allows the TS to start after the NIC has initialized.
From several posts I've read on this forum, this particular behavior was alleviated by a "wait for IP lease" mechanism built into the TS engine which was introduced in MDT 2010 SP1, I wasn't able to find any other confirmation whether
this mechanism is still in effect with MDT 2013. Another point worth mentioning from several other posts I was able to find is that this behavior appears to manifested itself on target workstations with SSDs, which would somewhat explain the faster
TS load time vs waiting for an IP lease. I've also tried to replicate this behavior in a non-SSD and low-performance VM environment and I wasn't able to replicate it.
My question: Does anyone else have experienced this behavior with MDT 2013 and if so, how did you resolve it? Or is this a bug?

I have this issue intermittently as well. For us, it coincided with the deployment of IP phones, which meant PoE switches all around. However, the problem persisted even after we turned off PoE to the ethernet ports from which we normally PXE
boot.
As this issue has been intermittent, I've backburnered it. When it does happen, I just wait for the lease to arrive then rerun the wizard.
Thanks for the feedback, that's true the TS can be resumed manually once the lease has occured but it defeats the purpose of an automated TS if I have to keep an eye on it and intervene if I need to.
The network guys here recommended putting wireshark or network monitor on it and figuring out just what the heck is going on. Basically, what Keith Garner said. They also disabled PortFast awhile back to see if that made any difference, and it did
not.

MDT 2013: Wizard Pages by Task Sequence

Hi,
I believe what I am trying to do is not possible from previous readings on this forum, BUT then I see something in my MDT 2013 OSD wizard that seems to indicate there might be a way to get it done. So here goes.
For my own demos, I am trying to develop a deployment share that is much like Johan Arwidmark's hydration kit. Some machines, like a domain controller or a SQL cluster are all well-defined: computer names, IP addresses, etc. are fixed and can be set
in customsettings.ini or in the Task Sequence with variables. However, I would also like the ability to have to deploy a "generic" machine where I can select roles, applications, etc.
This would require having different wizard pages shown for different task sequences. From what I've read, this may not be possible without developing a custom wizard (and that might be too much effort). However, I currently have two task sequences and depending
on which one I select, I see a different number of steps to complete? See screenshots. I don't know what I have currently configured that makes it like that.
(when I select "Domain Controller 01" task sequence) (Task sequence ID "DC01")
(when I select the "generic" task sequence)
Below is my customsettings.ini [the only rules file I have].
[Settings]
Priority=TaskSequence,Default
[Default]
_SMSTSORGNAME=Demo Deployment
OSInstall=Y
SkipCapture=YES
SkipAdminPassword=YES
AdminPassword=P@ssw0rd!
SkipProductKey=YES
SkipComputerBackup=YES
SkipBitLocker=YES
EventService=http://192.168.232.1:9800
SkipUserData=YES
SkipTaskSequence=NO
SkipTimeZone=YES
SkipBitLocker=YES
SkipSummary=YES
SkipFinalSummary=NO
FinishAction=SHUTDOWN
SkipLocaleSelection=YES
HideShell=YES
[DC01]
_SMSTSORGNAME=DC01 Deployment
SkipComputerName=YES
OSDComputerName=DC01
SkipDomainMembership=YES
JoinWorkgroup=DEMO
SkipRoles=YES
I would expect the settings for task sequence "DC01" to be applied after I select that task sequence in the wizard. That doesn't seem to work. The first task in the sequence is a "Gather" task that gathers local data and processes customsettings.ini.
I understand I can't override most settings from [Default] because they would have already been processed but as you can see, that's not what I am actually trying.
I am not opposed to having multiple rules files if that would work. However, it seems like that doesn't make much difference when it comes to actually seeing different wizard steps active. I've tried adding a second customsettings_dc01.ini file and having
a Gather step that specifically references that file in the "Initialize" group.
I've considered some alternatives to making it work this way, such as having multiple deployment shares and "linking" them (although I haven't done this before) so I wouldn't have to copy all the applications.
I would also set the computer name and all in the task sequence using variables, but that still doesn't address the problem.
Any insight is appreciated,
SA.

SpeedBird186 - There are several assumptions going on here.
1. by default MDT processes the CS.ini file *before* the wizard, and *after* the Task sequence has started. If you want CS.ini file to be processed just *after* you select your TS in the wizard, use Johan's trick above.
2. There are about 20 different wizard pages, and they don't appear in *all* scenarios. the wizard framework will attempt to do an intelligent job of filtering out pages that are not relevant to the scenario at hand. For example, in the graphic above, you
can see that the OS roles and Features page will appear/disappear. This can happen for example if the task sequence you selected earlier does or does *not* have a "OS Roles and Featrues" step in the Task sequence.
3. For me, the easiest way to process roles would be to create some new "Applications" and to put them in a folder.
Keith Garner - keithga.wordpress.com

MDT 2013 Wizard page not skipping

Hi all,
I am trying to reduce the amount of user intervention required for MDT 2013 to deploy a Windows 7 SP1 32 bit system from a Windows Server 2008 Standard box and I'm progressing well however, I've discovered that a wizard page won't skip. Specifically the
one that asks you to confirm time, time zone and date settings which appears right before MDT progresses to installing applications.
Here are the rules I have configured for my deployment share:
[Settings]
Priority=Default
Properties=MyCustomProperty
[Default]
OSInstall=Y
EventService=http://x.x.x.x
SkipLocaleSelection=YES
SkipTimeZone=YES
KeyboardLocale=0809:00000809
UserLocale=en-AU
UILanguage=en-US
TimeZone=255
TimeZoneName=AUS Eastern Standard Time
From what I've read, if you use a Skip wizard page option, there are prerequisite settings you must configure such as the keyboardlocale, userlocale etc and I've also gone through the MDT help topics andd found a table that contains these settings however
what I've found, is that although MDT will set the correct keyboard location and time zone settings, it still asks me to confirm it before proceeding to the installation of applications.
Am I missing anything? Does the order of the rules matter? Not sure what else to do.
Thanks in advance for any advice.

Yea, that should work, code snippet from DeployWiz_Definition_ENU.xml is:
<Pane id="SelectLanguageUI" reference="DeployWiz_LanguageUI.xml">
<Condition><![CDATA[ UCase(Property("SkipLocaleSelection")) <> "YES" or UCase(Property("SkipTimeZone"))<>"YES" ]]> </Condition>
<Condition><![CDATA[ Property("DeploymentType")<>"REPLACE" and Property("DeploymentType")<>"CUSTOM" and Property("DeploymentType") <> "StateRestore" ]]> </Condition>
</Pane>
IF you are still having problems, please copy your bdd.log file to a public share like OneDrive, and post the link here.
Keith Garner - Principal Consultant [owner] -
http://DeploymentLive.com

MDT 2013, Deploying Windows 8.1 on Surface and Dell Venue Tablets

I'm having numerous issues with Capturing Images and Deploying to Windows 8.1 Tablets. We are currently using Surface Pro 1, 2, and Dell Venue 11 Pro tablets. I am using a Windows Server 2012 computer with MDT 2013 installed. I can't get the tablets
to:
1-sysprep and capture using MDT 2013
2-Deploy a Task Sequence with a WIM and other applications attached. (I've tried using the simple standard task seq option with no luck)
3-I found another way to get a WIM (using imagex) but when i deploy task sequence it ignores my selection of applications to install outside the WIM and only installs the WIM (WIM 14gb = Win 8.1 Ent, Office 2013 x32, MS Updates)
Any help would be greatly appreciated. Everything is being performed within the LAN and with USB 2.0 thumbdrives for media.

Hi altimav8,
Are you trying to find out how to deploy Surface Pro method? Before capture the Surface pro image please download the latest drivers for the surface and made sure that they
were the only drivers that were going to be deployed. There have a specific MDT deploy support forum more about the MDT deploy related issue you can ask in MDT support forum.
MDT support
forum:
https://social.technet.microsoft.com/Forums/en-US/home?forum=mdt
The related guide:
Surface Pro - Enterprise Deployment Quick Start Guide
http://download.microsoft.com/download/2/0/7/2073C22F-2F31-4F4A-8059-E54C91C564A9/Surface%20Pro%20-%20Enterprise%20Deployment%20Quick%20Start%20Guide.pdf
Thanks for your understanding and support
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Second Exchange 2013 server in remote site

Just finished migrating from 2007 to 2013 and decommissioned 2007. Exchange 2013 is running in site A with 350 mailboxes on it. However, almost half of those users reside in site B so the plan is to introduce a second Exchange 2013 server to
this site and migrating mailboxes to it. There already exists a DC & GC in both sites.
My question is, immediately after I introduce Exchange 2013 into site B with CAS & MBX role, client computers from that site will start to receive certificate errors. Will updating the SCP on the new exchange server to point to the SCP on the exchange
server in site A be enough to mitigate that problem? What other precautions will I need to take? Has anybody been down this road?

Hi
You can introduce the second exchange server in the remote site and also setup a DAG. If you are using the same name on your certificate like mail.domain.com then you can use the cert for your second server as well. You need to make sure you have autodiscover
records setup correctly.
Hope this helps. Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

MDT 2013 deploying OS from USB Flashdrive failed - need to click OK everytime

We are using MDT 2013 with ADK 8.1 and deploying Windows 7 x64 using media (USB Flashdrive). We can successfully deploy Windows 7 x64b using ethernet cabel but not via USB-Flashdrive. This problem appears on all our HP EliteBook
Series, old as new computers series. We can boot into WinPE 64 bit and start the proper task sequence, all image is applied then after restart, after the logon screen appears there is an error saying that cannot find "USB media?".
But after clicking "OK" it works fine until next reboot, same thing again, but the drive is recognized!
I downloaded all USB drivers from HP website that holds USB 2.0 and 3.0 and drivers that contains open driver files like .inf and .dll files and injected them with the "Profile" that contains all drivers and packages.
It seems like it needs a timeout because of the script is trying to early to find the USB-flashdrive.
Any ideas?
Sorry for language, but you get the Point.
Best regards

Hi,
I would like you to clarify following questions with me:
1. Did you keep the USB plugged in during the restarting?
2. Have you make any task sequence to install applications after log in? If so, have them been installed properly?
Then, please help to collect a boot trace to let me know the details:
How to collect a good boot trace on Windows 7
http://blogs.technet.com/b/jeff_stokes/archive/2012/09/17/how-to-collect-a-good-boot-trace-on-windows-7.aspx
Please upload them to a file sharing service like Onedrive or "Rapidshare" and put a link to them in your reply.
Kate Li
TechNet Community Support

Deploy UDI Windows 10 with SCCM 2012 R2 and MDT 2013 Update 1

Hi,
Trying use "User-Driven Installation" with
SCCM 2012
R2 CU4 and MDT
2013 Update 1 for deploy Windows
10.
Created MDT Task Sequences with
template "Client Task sequence"
and Deployment Method "User-Driven Installation".
When I try to deploy I have error like:
Failed to run the last action: Error in the task sequence. Execution of task sequence failed.
The operation cannot be completed because other resources are dependent on this resource. (Error: 00001389; Source: Windows)
ZTI deployment failed, Return Code = 5001 InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Unable to create WebService class InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Command line returned 5001 InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Process completed with exit code 5001 TSManager 22.04.2015 11:36:57 1160 (0x0488)
Part smsts.log
!--------------------------------------------------------------------------------------------! TSManager 22.04.2015 11:36:57 1160 (0x0488)
Expand a string: WinPEandFullOS TSManager 22.04.2015 11:36:57 1160 (0x0488)
Executing command line: smsswd.exe /run: cscript "%deployroot%\scripts\ztierrormsg.wsf" TSManager 22.04.2015 11:36:57 1160 (0x0488)
[ smsswd.exe ] InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
PackageID = '' InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
BaseVar = '', ContinueOnError='' InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
ProgramName = 'cscript "C:\_SMSTaskSequence\WDPackage\scripts\ztierrormsg.wsf"' InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
SwdAction = '0001' InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Set command line: Run command line InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Working dir 'not set' InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Executing command line: Run command line InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Process completed with exit code 5001 InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Microsoft (R) Windows Script Host Version 5.12 InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Copyright (C) Microsoft Corporation. All rights reserved. InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Microsoft Deployment Toolkit version: 6.3.8216.1000 InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
The task sequencer log is located at X:\WINDOWS\TEMP\SMSTSLog\SMSTS.LOG. For task sequence failures, please consult this log. InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
ZTI deployment failed, Return Code = 5001 InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Unable to create WebService class InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Command line returned 5001 InstallSoftware 22.04.2015 11:36:57 1740 (0x06CC)
Process completed with exit code 5001 TSManager 22.04.2015 11:36:57 1160 (0x0488)
!--------------------------------------------------------------------------------------------! TSManager 22.04.2015 11:36:57 1160 (0x0488)
Failed to run the action: Error in the task sequence.
The operation cannot be completed because other resources are dependent on this resource. (Error: 00001389; Source: Windows) TSManager 22.04.2015 11:36:57 1160 (0x0488)
MP server http://sccm.domain.com. Ports 80,443. CRL=false. TSManager 22.04.2015 11:36:57 1160 (0x0488)
Setting authenticator TSManager 22.04.2015 11:36:57 1160 (0x0488)
Set authenticator in transport TSManager 22.04.2015 11:36:57 1160 (0x0488)
Sending StatusMessage TSManager 22.04.2015 11:36:57 1160 (0x0488)
Setting message signatures. TSManager 22.04.2015 11:36:57 1160 (0x0488)
Setting the authenticator. TSManager 22.04.2015 11:36:57 1160 (0x0488)
CLibSMSMessageWinHttpTransport::Send: URL: sccm.domain.com:80 CCM_POST /ccm_system/request TSManager 22.04.2015 11:36:57 1160 (0x0488)
Request was successful. TSManager 22.04.2015 11:36:57 1160 (0x0488)
Set a global environment variable _SMSTSLastActionRetCode=5001 TSManager 22.04.2015 11:36:57 1160 (0x0488)
Set a global environment variable _SMSTSLastActionSucceeded=false TSManager 22.04.2015 11:36:57 1160 (0x0488)
Clear local default environment TSManager 22.04.2015 11:36:57 1160 (0x0488)
Let the parent group (Gather Logs and StateStore on Failure) decides whether to continue execution TSManager 22.04.2015 11:36:57 1160 (0x0488)
The execution of the group (Gather Logs and StateStore on Failure) has failed and the execution has been aborted. An action failed.
Operation aborted (Error: 80004004; Source: Windows) TSManager 22.04.2015 11:36:57 1160 (0x0488)
Failed to run the last action: Error in the task sequence. Execution of task sequence failed.
The operation cannot be completed because other resources are dependent on this resource. (Error: 00001389; Source: Windows) TSManager 22.04.2015 11:36:57 1160 (0x0488)
MP server http://sccm.domain.com. Ports 80,443. CRL=false. TSManager 22.04.2015 11:36:57 1160 (0x0488)
Setting authenticator TSManager 22.04.2015 11:36:57 1160 (0x0488)
Set authenticator in transport TSManager 22.04.2015 11:36:57 1160 (0x0488)
Sending StatusMessage TSManager 22.04.2015 11:36:57 1160 (0x0488)
Setting message signatures. TSManager 22.04.2015 11:36:57 1160 (0x0488)
Setting the authenticator. TSManager 22.04.2015 11:36:57 1160 (0x0488)
CLibSMSMessageWinHttpTransport::Send: URL: sccm.domain.com:80 CCM_POST /ccm_system/request TSManager 22.04.2015 11:36:57 1160 (0x0488)
Request was successful. TSManager 22.04.2015 11:36:57 1160 (0x0488)
Executing command line: X:\WINDOWS\system32\cmd.exe /k TSBootShell 22.04.2015 11:37:31 696 (0x02B8)
The command completed successfully. TSBootShell 22.04.2015 11:37:31 696 (0x02B8)
Successfully launched command shell. TSBootShell 22.04.2015 11:37:31 696 (0x02B8)

MDT Updates for Windows 10 Technical Preview Build 10041
Если Вам помог чей-либо ответ, пожалуйста, не забывайте жать на кнопку "Предложить как ответ" или "Пометить как ответ".
http://zalozny.com.ua

Deploy Office 365 Pro Plus using MDT 2013

Hello,
I'm currently evaluating O365 E3 and am specifically looking into what my options are for deploying Office 2013 Pro Plus when rolling out a new PC image. Currently I use MDT 2013 to deploy the image to new PCs and install Office 2010 along with other
applications. Can I use C2R with a config file pointing to a local repository of the installation files with MDT 2013?

Hi
This blog post by Rens will help you:
http://renshollanders.nl/2014/02/office-365-automatic-deployment-of-office-365-with-mdt/

Suppress deployment wizard in remote site mdt 2013

Similar Messages

Maybe you are looking for