Suspect defective cdrom on Ultra Enterprise 450 server

Hello,
Would you assume that the CDROM is brocken if
ok> boot cdrom just hangs
I would assume that the alias is set automatically.
The CDROM does just nothing then but lights up when the machine starts.
I tested it on a pc and it behaved just the same.

I had the same issue on one of our E450's and the test requested by Sun support was "ok>boot cdrom"
when this failed to work they replaced the drive and all was well.

Similar Messages

  • Sun Ultra Enterprise 450 server

    Can any Please answer this question as I have an E 450 and that has a backplane installed that can hold 20 Disk what is the MAX disk Size that I can buy for this servers is 36, 72 or 146 GB or larger then that .Any help will be appreciated .thanks in advance

    The max disk size that you can put in this server is a 36GB disk and details of this disk and every other disk that is supported by the E450 can be found here.
    http://sunsolve.sun.com/handbook_pub/Systems/E450/components .html#Disks

  • Ultra Enterprise 450 Server

    I couldn��t see my messagge on the web, so this is my second time:
    After installing a new UPS my server doesn��t comming up.
    No indications on the front panel. No fans running. Nothing at all.
    Just possible to see in both Power Supplies (rear side)and green color leds:
    - Load Status
    - AC-Present Status
    DC Status is off
    I��m wondering if both power supplies are bad.
    Any more ideas??

    Just a shot in the dark (yes, pun intended).
    I hope the UPS is NOT conected to TTYa, because that is your console port of the system. Console is probably waiting for proper input connectivity.
    You may need to open a service case with the vendor of that Uninterruptible Power Supply and seek help to confirm proper connections.

  • How to install Solaris 10 on sun ultra enterprise 450

    I just got a used sun ultra enterprise 450 and need to get a username and password. If I cannot get easily how do I reinstall the OS. What OS can I put on its? I am new to some equipment. It also came with a a storage unit for extra hard drives and how would I use it and set it up also?
    It now says type ctrl-d. What do I do?
    http://www.unix.com/sun-solaris/114206-how-get-root-password-how-install-sun-os.html
    http://www.linuxquestions.org/questions/solaris-opensolaris-20/how-to-install-solaris-10-on-sun-ultra-enterprise-450-739614/

    This same question was cross-posted to another forum site
    [http://www.linuxquestions.org/questions/solaris-opensolaris-20/how-to-install-solaris-10-on-sun-ultra-enterprise-450-739614/|http://www.linuxquestions.org/questions/solaris-opensolaris-20/how-to-install-solaris-10-on-sun-ultra-enterprise-450-739614/]
    with the same unintelligible drivel.
    O.P.
    Go to Docs.Sun.Com and get the system's documentation. Also go get the OBP 3.x Command Reference manual while you are there. All you questions are answered in that documentation, except for those that are easily found with Google.
    [Example of a Google search for your question.|http://www.google.com/#hl=en&q=solaris+root+password&aq=f&oq=&aqi=g9&fp=KxYPMM6r3XA]

  • Where can I get firmware for ultra enterprise 3000 server?

    Hello,
    Where can I get firmware download for ultra enterprise 3000 server so I can run in 64 bit mode?
    Thanks,
    Keith

    go to URL htpp://uk.sunsolve.sun.com & in search engine type your question firmware for ultra enterprise 3000 server ,
    thanks
    bhogle

  • Adding new Scsi hard disk to Enterprise 450

    I have an Ultra Enterprise 450 2x300Mhz. I want to install another 8Gig or 18Gig Scsi hard disk to the current configuration, but I dont want to re-install solaris, without giving any damage to the system.
    How can i do this without losing any data in the current config.
    Regards.

    Solstice disk suite is a good tool for the job of managing your disks. Lets say that you want to increase the database volume, you could create a stripe accross the current disk and a fourth disk. So if you installed another 9GB drive you could create a volume as follows:
    1/ Get a time window, take the database offline and unmount the database slice ( shutdown -y -g<i>n**</i> -iS ).
    The shutdown command is a good way to set your system up for a backup, n** is the number of seconds before the system goes down to level S. With a properly configured SVR4 UNIX initializing to level 1 should unmount all but / and should stop all services.
    2/ Dump the database filesystem to tape.
    3/ Recreate a new partition table for the disk:
    Slice 6 unassigned 30MB
    Slice 7 /usr 8GB ( remainder of the disk
    4/ Create an identical VTOC on the new disk
    5/ Create meta data database:
    # metadb -a -f -c 2 c0t3d0s6
    # metadb -a -c 2 c0t4d0s6
    6/ Create a volume out of the remaining slices from each disk:
    # metainit d0 1 2 c0t3d0s7 c0t4d0s7
    7/ Create a new UFS on the volume and mount it:
    # newfs /dev/md/rdsk/d0
    # mount -F ufs /dev/md/dsk/d0 /data
    8/ Restore the data to the new filesystem and restart the database application
    This is just an example, but if you read through the documentation for your version of Disk Suite you will understand this example more. As I said in my last post, this is a hard question to answer, most disk configuration are unique and depend on what application you are using. A typical configuration for an E450 with 4 slots might be - disk 0 and 1 containing OS and mirrored for availability and the ramaining disks configured for some type of volume to be used for data. Keep in mind that with the E450, you can expand up to 20 drives, so if you can get another backplane you may be able to reconfigure your system to give better availability.

  • Installation Iplanet 4.1 Enterprise Web Server on Linux RedHat 7.1

    I am trying to install IPlanet 4.1 Enterprise Web Server on Linux RedHat 7.1.
    After unloading the software from CDROM to a temp directory, and run ./setup, I get the following error:
    eroor while loading shared libraries; libncurses.so.4: cannot load shared object file : no such file or directory.
    Has anyone know how to resolve it??. Thanks.
    regards,
    Benny Tan

    I have answered for this topic previously for another thread. Please follow the URL to see the answer.
    http://forum.java.sun.com/thread.jsp?thread=257294&forum=14&message=968185

  • How to proactively monitor health of  the Disks on Sun Enterprise 450

    We have been encountering frequent disk problems lately, most commonly disk read/write errors. I want to see if there was a way to monitor and anticipate problems in a proactive manner instead of reacting after the problem?
    We have a Sun Enterprise 450 with 20 disks and run Solaris 8. I have a metastat script in the cron to check the status every hour. Can anyone advise me on an automated processes which can monitor and report health of our disks before anything goes wrong?
    Thanks in advance.

    Perhaps it is a good idea to check the grown defect list from a disk.
    You can check the list with the "format" command (defect / grown).
    Some entries in this list are OK, but if its grown fast, you should
    consider to change the disk.

  • How do I set up a private enterprise messaging server?

    The iPad and iPhone messaging app seems to require that the messaging server must be in the Apple cloud.  Is there a way to set up a private enterprise messaging server?

    Is there a way to set up a private enterprise messaging server?
    Yes:  http://lync.microsoft.com/en-us/Pages/unified-communications.aspx

  • IPlanet Enterprise Web Server hosting a portal server

    Has anyone tried to port the Plumtree portal server component to iPlanet Enterprise Web Server (aka SunONE Web Server, v6.0 or later)? Plumtree doesn't support this, but I am trying to merge a custom SSO authenticator to the Plumtree portal (v5.0.1).
    I have this working great in security mode 0 (with SSL turned off), but I am having a difficult time getting past one last issue in security mode 2 (full SSL mode). I can get the portal server to run fine in mode 2 through Tomcat on the same machine, using the same certificate and JRE. I can also get iPlanet to run other servlet applications fine with SSL turned on. However, there appears to be either: (1) an incompatibility between iPlanet's NSServlet plug-in that handles servlets and the Plumtree framework classes that set up replies via SSL, or (2) a configuration error in my setup somewhere. I'm hoping that (2) is the real culprit, but I've tried just about everything I can think of, and haven't been able to resolve this problem.
    The server starts up fine and I can load non-portal content without a problem. But when I log in, the portal's main community page that should be returned is not being returned to the client. PTSpy doesn't indicate any problems, so I know the content is being built by the portal correctly, but the built page is never being sent back to the requesting client.
    Here is the error that gets logged to iPlanet's error log:
    [29/Dec/2003:15:05:53] failure ( 2772): Internal error: Unexpected error condition thrown (unknown exception,no description), stack: java.lang.NoClassDefFoundError: javax/net/ssl/SSLSocket
    at sun.net.www.http.HttpClient.parseHTTPHeader(HttpClient.java:793)
    at sun.net.www.http.HttpClient.parseHTTP(HttpClient.java:702)
    at sun.net.www.protocol.http.HttpURLConnection.getInputStream(HttpURLConnection.java:583)
    at java.net.URL.openStream(URL.java:960)
    at org.apache.xerces.readers.DefaultReaderFactory.createReader(DefaultReaderFactory.java:149)
    at org.apache.xerces.readers.DefaultEntityHandler.startReadingFromDocument(DefaultEntityHandler.java:493)
    at org.apache.xerces.framework.XMLParser.parseSomeSetup(XMLParser.java:314)
    at org.apache.xerces.framework.XMLParser.parse(XMLParser.java:1097)
    at org.apache.xerces.jaxp.DocumentBuilderImpl.parse(DocumentBuilderImpl.java:195)
    at javax.xml.parsers.DocumentBuilder.parse(DocumentBuilder.java:124)
    at com.plumtree.openfoundation.xml.dom.XPBuilder.LoadDocumentFromURI(XPBuilder.java:203)
    at com.plumtree.xpshared.jsutil.JSRegistry.LookupJSComponentVersions(JSRegistry.java:243)
    at com.plumtree.xpshared.jsutil.JSRegistry.GetJSComponentVersions(JSRegistry.java:184)
    at com.plumtree.xpshared.jsutil.JSRegistry.GetJSComponent(JSRegistry.java:465)
    at com.plumtree.xpshared.jsutil.JSRegistry.GetJSComponent(JSRegistry.java:444)
    at com.plumtree.uiinfrastructure.statichelpers.ConfigHelper.GetCommonJSIncludes(ConfigHelper.java:1330)
    at com.plumtree.uiinfrastructure.form.AFormAS.DisplayCommonJavaScript(AFormAS.java:59)
    at com.plumtree.portalpages.common.uiparts.PlumtreeAS.DisplayCommonJavaScript(PlumtreeAS.java:88)
    at com.plumtree.portalpages.common.uiparts.PlumtreeDP.DisplayHead(PlumtreeDP.java:599)
    at com.plumtree.portalpages.common.uiparts.PlumtreeDP.Display(PlumtreeDP.java:112)
    at com.plumtree.portaluiinfrastructure.activityspace.Interpreter.ProcessDisplayPageOrRedirect(Interpreter.java:816)
    at com.plumtree.portaluiinfrastructure.activityspace.Interpreter.HandleRequest(Interpreter.java:1589)
    at com.plumtree.portaluiinfrastructure.activityspace.Interpreter.DoService(Interpreter.java:448)
    at com.plumtree.uiinfrastructure.web.XPPage.service(XPPage.java:141)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
    at com.iplanet.server.http.servlet.NSServletRunner.invokeServletService(NSServletRunner.java:919)
    at com.iplanet.server.http.servlet.WebApplication.service(WebApplication.java:1061)
    at com.iplanet.server.http.servlet.NSServletRunner.ServiceWebApp(NSServletRunner.java:981)
    It looks like a Java classpath issue, but I've verified (even in the same log file with java debugging turned on) that the SSLSocket class is getting loaded. I've even tried moving the specification of the jar file containing this class (jsse.jar, part of the JRE) to the beginning and end of my classpath setting.
    I'm using the same JRE that is bundled with the Tomcat release supplied with my Plumtree 5.0.1 installation (1.4.1_02).
    I've posted a similar message on a couple other forums (Java and iPlanet-related) and haven't found an answer yet. Does anyone have any ideas?
    John

    In case anyone else experiences this, I have apparently stumbled upon an issue with iPlanet's handling a specified JRE/JDK instead of the supplied JDK in iPlanet (SunONE) Web Server v6.0, SP5, though I found a way around it to resolve my problem.
    I had been specifying a different JRE to run with through iPlanet's administrative server manager. However, even though I was specifying to load all the JRE's jar files in my classpath setting, iPlanet was only loading the rt.jar file for my specified JRE. With verbose logging turned on, the error log was indicating that the other classpath specified jar files were being loaded, but apparently they were not being used. The JDK that was released with iPlanet appears to be being used for all other JRE classes outside of those defined in rt.jar. Since the JDK supplied with the iPlanet release didn't contain jsse.jar, which contains SSL support, it was not being loaded and was causing the problem I was seeing.
    Instead of specifying the JRE of a different JDK that I was using, I changed the global setting in the administrative server manager to override the entire JDK. This has resolved my problem.
    So if you specify a JRE to override the iPlanet supplied JDK/JRE, it appears that only the rt.jar file of the specified JRE will be loaded, and the jar files associated with the iPlanet-supplied JRE will be used for all other classes. Specification of a complete JDK to override the supplied one will resolve this, and the portal server appears to work fine now in any security mode setting when hosted on iPlanet Web Server (SunONE), even though Plumtree doesn't support that as a host server application.

  • Enterprise Web Server

    Is there a way to use Apache Web Server to provide access to Server
    Web
    Folders without using Enterprise Web Server.
    I have a server I upgraded to NetWare 6, this server has Enterprise
    Web
    Server running on it. After the upgrade the web part stop working. In
    a
    earlier post I had mentioned that I upgraded it from Novonyx; I had
    comments of can't you drop Novonyx, or why are you still using Novonyx
    when Novell is trying to go to Apache for its Web Server. I did as
    suggested and renamed the Novonyx folder and reinstalled Enterprise
    Web
    Server, and reinstalled the SP3.
    When you install Enterprise Web Server from the NetWare 6 installation
    CD, It still adds a Novonyx folder. So the part of why are you still using Novonyx is a poor statement to make in trying to trouble shoot a
    problem.
    Steven

    Nhunguyenvan,
    > I useing Windows7, now I want conect to server setup Novell 6.0. Can you
    > help me. Thanks a lot!
    Connect to the webserver on NetWare 6.0?
    - Anders Gustafsson (Sysop)
    The Aaland Islands (N60 E20)
    Novell has a new enhancement request system,
    or what is now known as the requirement portal.
    If customers would like to give input in the upcoming
    releases of Novell products then they should go to
    http://www.novell.com/rms

  • Install 11.2.0.3.0 database on Red Hat Enterprise Linux Server v.5.7

    1. if I need to install 11.2.0.3.0 database on Red Hat Enterprise Linux Server v.5.7,
    Here I see 11.2.0.1.0 for Linux x86-64 on the following website._
    http://www.oracle.com/technetwork/database/enterprise-edition/downloads/112010-linx8664soft-100572.html
    Do I download the following and then apply the 11.2.0.3 patch?_
    Oracle Database 11g Release 2 (11.2.0.1.0) for Linux x86-64 Linux.x64_11gR2_database_1of2.zip (1,239,269,270 bytes) (cksum - 3152418844) linux.x64_11gR2_database_2of2.zip (1,111,416,131 bytes) (cksum - 3669256139)
    2. I need to install 11g and 10g in a same server, I am also looking for a good document.
    Thanks.
    Jack

    user3023234 wrote:
    thanks. I will look into it.
    how do you install 10.2.0.4 and 11.2.0.3 on the same server?You can install multiple homes in a server.
    Every Software dump consists of installer(runInstaller).
    Even you can install same Oracle version & release in same server by differentiating Folder names.

  • 9i Enterprise Management Server License problem

    9i database standard edition can use Enterprise Managament Server?
    Enterprise Management Server can send a alert e-mail then some tablespace have large than the setting size.

    Questions like this should be addressed to your Oracle sales representative. No one here can give you a reliable answer,which passes into law. In general Management Packs require Enterprise Edition.
    Werner

  • Can't connect to KepWare Enterprise OPC server

    I am trying to connect to the Kepware Enterprise OPC server with Server Explorer 2.4.1 but get a message 'The system cannot find the file specified' 0x80070002. I have modified the DCOM setting for XP SP2 as described in the Kepware documentation. Is there a way to resolve this issue?
    Thanks
    Harry

    Hello,
    Can you explain exactly how you are attempting to connect to this OPC Server and also any of it's properties that are set in Server Explorer. At what point do you get this message? Have you been able to connect to that OPC Server on that machine, or any machine before?
    Cheers
    Tom | NIUK

  • I couldn't login to the Enterprise Manager Server by EMC

    Dear all:
    couldn't login to the Enterprise Manager Server by Enterprise Manager Console.
    EMC is in Start Menu->Programs->OWB_ORACLE_HOME->Warehouse Builder->Enterprise Manager Console.
    After clicking EMC, then the screen is represent by Login window at my database when I selected my database.
    But, when I put user name/password in this window, there is no response.
    How can I login to EMC? When I checked manual, I found that I have to start Oracle Management Server but I don't know how I can start OMS. Also, how can I create OEM repository?
    Please let me know what it is problem.
    Thank you.
    JWS.

    Hi
    Enterprise Manager Server is a service, you can start it in the control panel/administrative tools/services.
    To create a repository run the enterprise manager configuration assistant.
    To login to EMC se the help for the default username/pwd.
    Ott Karesz
    http://www.trendo-kft.hu

Maybe you are looking for