Swapping Controller cards

Hello,
We have an orginal Xserve RAID driving 14 drives. we can not see one side of the raid we think it may be the controller card. Is it possible to swap these cards without effecting the raid set up and data?
Also, where is the raid information stored? On the drives? On the actual controller cards?
Thanks
Message was edited by: Rick Hegyi

The info about the raid set is on the (disks of) the raid set itself. The settings of the card are on the card. This includes IP, mail, cache, ... Also the firmware is probably out of date.
Since IP is one of lost settings, make sure you can connect to the box (either through the other card or through a direct connection to the card).
When you update the firmware, the complete xraid will reboot.

Similar Messages

G3 Modem and ATA Controller Card

I am upgrading a B&W G3 350 MHz Yosemite running Tiger for some friends. They use dial-up (pooh) and the B&W did not ship with an internal modem. I found an Apple OEM on welovemacs.com for $60 ($10 more than the Apple USB). I am not sure which route to go (internal or USB). I am in a timed situation, so I am also considering a PCI modem. Any suggestions on the PCI modem (brand and model)? I know Tiger will not support some PCI modems.
Also, the G3 will not support larger HDDs. It currently has a 40 Gig drive in it. I tried installing an 80 Gig, but the ATA controller chip (Rev 1 logic board) did not recognize it. Any suggestions on a PCI based ATA controller card (brand and model)? Also, do these ATA controller cards usually ship with the power and data cables, or do I need to buy them separately? If so, any suggestions on which ones to buy and where?
I would appreciate any help as quickly as possible.
Thanks,
Thomas

Grant,
"Only when you start to use them do you begin to notice more than a casual amount of crashes, lock-ups, and eventually, data corruption. An 80 GB hard drive should be recognized immediately if it is correctly cabled and the straps are set correctly. Both 80 GB and 40 GB drives may be encountering corruption problems on the built-in controller."
The 40 GB drive has been in this machine for at least 4 years. It was originally my machine given me by a Mac Genius buddy. I used it for over a year before I bought my G4. I then loaned the B&W to my cousin who used it for over 2 years before HE bought a G4 and returned the G3 to me.
When I installed the 80 Gig drive (which already had 10.3 installed), the machine would not boot from it. I booted from the Tiger install DVD and tried to install Tiger. The installation got all the way to the end, then the installation seemed to stop. I left the machine sit for about an hour, then heard the boot tone of the machine re-starting. It never booted, though. I got the gray Apple screen and could actually hear the "Welcome to Tiger" music coming from the speaker, but the gray Apple screen never went away.
I tried re-jumpering the drive, thinking I had gotten the jumper opposite of what it should be, but that didn't do any good either. I tried putting the drive in my Granite Digital external Firewire HDD casing, but the drive would never mount on my G4. So, I re-re-jumpered the drive back to the way I originally had it jumpered. It mounted on my G4 just fine at that point. So, I then installed Tiger via the external Firewire casing using my G4 tower. Tiger installed successfully, and I put the HDD back into the G3, but it STILL would not boot. It would never get past the gray Apple screen, or the machine would kernel panic if it did.
So finally, in desparation, I put the old 40 Gig that was in the machine when my cousin shipped it back to me, back into the G3 and it booted from it just fine. I later did a clean install of Tiger, and the machine still boots fine.
So, as you can see, it really seems that the ATA controller chip does not like the 80 Gig drive.
"Why not broaden your options with an external modem?"
I may indeed decide to go with the Apple external USB, but was told by a Specialist at the Apple Store that the new Apple USB modem might not work with the G3. My friend, whose parents I am setting the G3 up for, owns a MacBook Pro, so he can use the Apple USB if it does not work with the G3 and when and if his parents get broadband.
I still would like to know if a PCI based modem will work with the the G3. I found a post on this board late last night (after I posted this thread) where a user had a question similar to mine. He/she was trying to swap a PCI modem between a PC and a B&W. Whoever responded to the post stated that the B&W will not support ANY PCI based modems. It will only support the OEM Apple modem that plugs into the logic board near the USB and Firewire ports or an external USB modem (similar to, but not specifially the Apple USB modem).
Thanks,
Thomas

Bad RAID Controller Card?

One of the arrays in my Xserve RAID had disappeared from the network and RAID admin software. All the disks that make up the array have green lights and appear in RAID admin. When the host PC reboots this array is no longer detected in the Apple Fibre Channel card BIOS. After having swapped cables around I reckon the RAID controller card has failed.
Is it safe to swap the top and bottom RAID controller cards to prove the diagnosis or does the controller hold information specific to the diskset it is connected to?

The diskset info is stored on the drives, so its perfectly fine to swap controllers.
On that note however, first of all make sure you really jam that controller board in there well... first time we swapped and it wasnt in there perfectly secure, 3 drives went red and the rest was history. Also, if your controller is acting up, definitly make sure things are backed up when swapping between sets... when we've had controller issues, its usually only been volumes going down on the computer's side, but I have heard of raid admin shooting back drive errors and turning things red as well.

Problem with NEO2 and sata controller card

1.Product Type: MSI K8N Neo2 Platinum (MS-7025)
and the controller card is a InnoVision DM-8301 and the hard drive is a Seagate ST3320620AS
2.BIOS version: The newest one, 1C0 or something.
3.External VGA Type: Geforce 6800 GT
4.CPU Type: AMD 64 3500+
5.Memory Type: G Skill ZX 2048mb.
6.Power Supply Type:
7.Operating System: Xp Pro
8.Problem Description:
Hello. I have a strange problem with my controllercard. I wrote this text to InnoVision suport and they send me files and bios updates for a whole week and it was still the same problem. And then i tried the card in an older computer and everything worked fine.
I wrote
"Hello. I got some problems with my new controller card. I can find my new harddrive ,that's conected to the controller card, when iam inside windows and it's seems to be no problem. I can look on every seting on it and everywhere i look i can read "No problem". I Also did some test with the seatools programe and everything was fine. But when i schould copy files to it the coumputer start lagging after a few seconds and i cant do anything. After a while i can move the mouse around but the it laggs again. My computer is overclocked at the time but i have tried to use the harddrive when it's not clocked also. Also when im goin in to teh controlpanel and starts the setings for Sillicon Images sata controll and have music on my computer, the music laggs for a very very short moment. Something must be wrong and i can not find it."
It's still the same problem in my computer. The older computer had a MSI moderboard with a VIA chip and i have a nForce 3. InnoVison said i should talk to you about this problem. I have 3 harddrives but i use this controllercard because i want to have my computer overclocked and then i can't use 2 of the sata ports as i think you know.
I would be very thankful if you could help me with this problem.
//Martin

I've used a noname SATA pci card (non raid) with SIL3112 on my neo2 without problems with 1C bios.
Think you may try with a disk lower than 48bitLBA need (137GB barrier), eg a 120GB disk
Quote:
have the InnoVision EIO DM-8301 and had alot of problems using it with WD 160MB SATA drive.
I am using Intel 865 based MB with 2 original SATA channels. The original SATA channels are bootable.
I could not used the EIO card with 160G HDD. The whole setup is working only after I connected oine of my 120G Segate SATA HDD to the EIO Sata card.
I think this card do not properly support HDD above 120G.
Please respond to: [email protected]
http://www.devhardware.com/forums/storage-devices-80/sata-as-boot-20080-2.html
Btw: you have xp sp2 ?
48bitLBA is not enabled in the first version.
http://www.48bitlba.com/winxp.htm
Edit:
Here's another with complete different setup and same problems
http://forum.tweakxp.com/forum/Topic212148-4-1.aspx
I doubt it has anything to do with your motherboard and/or bios.
Btw: I looked at innovision and their drivers in download area are very old.
Get the latest SIL3112 drivers for XP here:
http://www.siliconimage.com/support/supportsearchresults.aspx?pid=63&cid=3&ctid=2&osid=4&
And remember 3112 is sata150 only , so it's not sure it will work with your drive at all .
Anyway it should be set to fixed sata1.5G with jumper - not certain the controller can autonegotiate
without trouble. You cannot have command queing enabled either , disk support only NCQ and controller TCQ
so having command queing set ON will cause major conflicts in data transfers.

Mac Pro RAID and Boot Camp and eSATA controller Card

Hello all,
I have carefully read the topics concerning the Apple RAID card and its inability to run Boot Camp. Of course, I read this after placing my order. I have been mulling over my alternatives based on everyone's input. Here is what I want to do and how I think I can get there:
My system, when it finally arrives and is assembled will be:
Mac Pro 3.2GHz
12MG RAM
4 x 1TB hard drives
Apple RAID Card
ATI 2600
Except for the RAID card, the memory and drives are third party.
My plan was to create a RAID 5 with 3 of the internal drives, with the OS and apps on the non-RAIDed drive. I wanted to install Windows in a Boot Camp partition, but since learned this is not possible with the Apple card. I also planned on using the OWC Mercury Elite RAIDs I have (each enclosure house 2 x 500GB drives, and I have 4 enclosures for a possible max of 4TB of back up) to handle Time Machine (or other BU strategy) for the internals.
I have not received the Mac yet, so cannot look inside. From what I can gather, the Graphics card will occupy the Slot 1. The Raid Card will occupy Slot 4. This leaves me with only one 4x slot for a 4 port eSATA controller card (such as the RocketRAID 2314)
As I see it, I have a couple of obstacles to overcome, and I would appreciate advice/feedback on my possible solutions.
Problem 1: In order to use my existing OWC RAID enclosures, I need TWO controller cards, each with 4 eSATA connectors. Unless I scrap the 500GB drives for 1TB drives, I am stuck. Am I correct in assuming I cannot use Slot 2 for another controller card? Is there any work around?
Problem 2: Boot Camp. Can I purchase the Newer Technology extender cable to access the two eSATA ports on the Mac's motherboard to attach an external SATA drive for this purpose?
Questions:
1) I assume I can set up an external RAID (another RAID 5?) with my OWC drives and use Time Machine to back up to them?
2) From the illustration in the Mac Pro manual I downloaded, there appear to be only 4 PCIe slots, but 5 openings (one seems to be aligned with the back-up battery). I assume this is the double-wide space for the graphics card. Can I use the extra opening for the Newer Tech ports since there is no card taking up space?
3) Should I remove the Apple RAID card (resell on ebay) and buy the CalDigit RAID Card? It has the virture of allowing a Boot Camp install AND has ports that I can buy SAS to eSATA cables for, allowing me to use all of my OWC drives.
The CalDigit Card sounds good, but I would like to make the Apple card work if I can. Also, with the OPTIONAL battery back-up, the CalDigit card isn't that much less than the Apple card. Besides, I cannot find this card anywhere, everyone's at NAB, and it's Passover next week. AND I need to get this system up and running ASAP so I can begin making the money to pay for it.
Any input would be most welcome.
Gary

Problem 1: In order to use my existing OWC RAID enclosures, I need TWO controller cards, each with 4 eSATA connectors. Unless I scrap the 500GB drives for 1TB drives, I am stuck.
You could get new enclosures with SATA port multipliers for up to five drives per SATA port.
Am I correct in assuming I cannot use Slot 2 for another controller card? Is there any work around?
Apple says any PCI-e card should work in slot 2
<http://developer.apple.com/documentation/Hardware/Conceptual/HWtechPCI/Articles/pciimplementation.html#>
"Mac Pro detects whether an inserted card is PCIe 2.0 (5.0 GHz) or PCIe (2.5 GHz) and selects the operation depending on the card's maximum capability."
but there have been reports of trouble (maybe caused by the recent firmware update). Check with the card maker to be sure.
Problem 2: Boot Camp. Can I purchase the Newer Technology extender cable to access the two eSATA ports on the Mac's motherboard to attach an external SATA drive for this purpose?
No. Those ports are only usable from OSX, but if you only have one optical drive, you can mount another drive in the lower optical drive bay with a Pro Caddy for use with Boot Camp.
<http://www.transintl.com/store/category.cfm?Category=2704&RequestTimeOut=500>
This simplest connection is to use the optical ATA cable (with a SATA to ATA adapter for a SATA drive).
If you want to use a SATA connection, use a iPass to SATA cable from the iPass port on the Mac Pro logic board, which is normally used for the four SATA drives when there is no RAID card.
<http://www.pcconnection.com/IPA/Shop/Product/Detail.htm?sku=7252016>
Questions:
1) I assume I can set up an external RAID (another RAID 5?) with my OWC drives and use Time Machine to back up to them?
Yes
2) From the illustration in the Mac Pro manual I downloaded, there appear to be only 4 PCIe slots, but 5 openings (one seems to be aligned with the back-up battery). I assume this is the double-wide space for the graphics card. Can I use the extra opening for the Newer Tech ports since there is no card taking up space?
It looks like it should work if you route the cables just above the graphics card.
<http://www.newertech.com/Static/articles/images/macensteineSATA_5.jpg>

SATA11 is it compatable with all controller cards

I want to add 500gb HD's to my G4 Giga and know I need a SATA controller card, I am considering this one card pic is this card compatable with SATA11 hard drives?
Powermac G4 Giga-ethernet Dual 1.2ghz 100bus 2 Gig Ram 2xHD 80gb+120gb USB1+2/FW Mac OS X (10.4.9) wireless network

Thanks Japamac, can I go through this deadhead style...
You can install as many OS's as you want. When you
set your Startup Disk Preferences, you are able to
select the OS that you want, as well as the disk that
you want.
Does this mean I have to make a partion thing on the same disk for each (even the same) OS?
Do I use the original install disks to do this?
Another way to select startup disk/OS, is to boot
while holding the Option key. This will open the
Startup Manager, and allow you to select which and
where you want to boot from.
This is the screen I remember from my Apple Care Plan Help Desk days
It is a good idea to have a second (and third)
bootable disk in your system.
Is the third disk on a partion thing ( I have researched this and have found, using "disk utility" I can make "partitions", if I understand correctly, my machine will "see" a partition as a separate disk, am I miles off?
That way, heaven
forbid, should one disk have trouble booting, you can
use the Startup Manager to select an alternate disk,
and then diagnose and repair the ailing disk from
there.
Do I use "disk utility" from another partition disk to do this?
This is, actually, a very important thing to
have in your system. by all means, install the OS on
the other disk.
A partition on the 120gb, how big should the partition be?
Remember, to keep both disks backed up. So, don't
give up on your external drives all together. They
are VERY useful.
This is where you are going to hate me... I dont have any externals or back ups.... this is why I am trying to work out what to do... I back up my photo's to DVD when I have enough, its not good practice because it can take a months worth before I have time to physically go through all the work to decide what I will archive to DVD, I would love for all of the work to automatically copy itself to a safe place.
While we are on the subject, a very good way to
backup, is to use Super Duper. This is a clone
utility. SD will copy bit for bit, your drive, and
then make that backup bootable. This is a very nice
feature. Also, after that, you can use the Smart
Update feature, which updates any changes of a volume
to it's clone. This way, you always have an exact
copy of your system and data. Invaluable!
This is obviously what I need... I will download it and try to understand its functions
I like OWC, myself. Even with shipping and tariffs to
Japan, it is most often cheaper to do so. Also, the
company is very reputable, has great service (try
their live chat) and stands behind what they sell.
OWC also has lots of install tutorial video (and
PDF's) in their support section. Check it
out.
I have trusted OWC since you recommended them for my processor upgrade and have just ordered the SATA controller from them and am going to get a 500gb internal HD for now until I can learn to rationalise my disk space... at the moment my files are just copies of themselves on the same disk (120gb)
Hey Japamac... I have to say thank you to you sir, you have obviously put a lot of time and effort into your reply and I really do appreciate it...
As Arnie says.... "I will be back"
G4AGP(450)Sawtooth,
2ghz PowerLogix, 2gbRAM, RaptorSATAATA, ATI Radeon
9800 Mac OS X (10.4.8) Pioneer DVR-109, 23" ACD,
Ratoc USB 2.0, QCam Ultra, Nikon Coolscan
Powermac G4 Giga-ethernet Dual 1.2ghz 100bus 2 Gig Ram 2xHD 80gb+120gb USB1+2/FW Mac OS X (10.4.9) wireless network
Powermac G4 Giga-ethernet Dual 1.2ghz 100bus 2 Gig Ram 2xHD 80gb+120gb USB1+2/FW Mac OS X (10.4.9) wireless network

975X and a PCI Controller Card

I am trying to install another SATA controller card to I can flash my firmware on my 360. But for what ever reason this board (975X) isn't allowing me to ever boot to the PCI card.
Any ideas on what settings I need to pick to do it?
Thanks!

I think I have tried that and nothing worked. The card is seen in Windows but just not while booting. I'll try it again here once my computer is done doing some things to where I can reboot. I wanted to make sure I was doing it right and it sounds like I am.

Recommend a 4 way SATA controller card?

I am having huge problems of finding a SATA controller card that:
1. Can attach 4 discs
2. No raid (i will use ZFS)
3. supports NCQ
4. supports SATA II (i.e. 3Gbps)
If anyone know of a card that works, please post the model here, so I can buy it. Ive looked everywhere, but it seems that the SATA chipset that are supported, can only be found on motherboards, and not as standalone cards.

Ok, this card requires a PCI-X slot. It is therefore suited to server motherboards. I have heard that PCI-X will work with an ordinary PCI slot without problems. Can anyone confirm this?

PCI USB2 Controller card conflicts with network card

I've installed a PCI USB2 controller card since my motherboard (IWill K266-R) only has support for USB1. However, the card seems to conflict with one of my network cards, because traffic on the internet-connected NIC is very slow, and often drops completely. Traffic to and from the other (local) NIC seems to work fine, though.
I have tried moving around all three cards in different PCI slots, I think I've tested almost every possible combination by now. I've also tried disabling as much as possible in BIOS, such as onboard sound, serial and parallel ports etc. I've tried lowering the FSB.
For now, I've removed the controller card, and is using the USB1 ports on the motherboard instead. This is very frustrating, though.
Does anyone have any suggestion on what I can try next? I've browsed forums, both this and others, but I haven't found any more hints on what to try. Could there be some setting in Arch that could affect these sorts of things?

"I guess the ATA100 card will work fine correct?"
If you mean large drive support, it may provide that or may require a firmware update to do so. You should check the manufacturer's web site for specifics. All ATA-133 cards do provide 48-bit LBA for large drive support. I'd return the Ultra ATA-66 card to the eBay seller, although many refuse to pay for return shipping, even when the mistake is their own, either through ignorance or deliberate misrepresentation. In cases such as this, it's sometimes more cost-effective to swallow the loss and keep the incorrect part.
"Will adding a jumper apply for a ATA100 card as well? I'll need a blue and gray ribbon correct?"
If you use an 80-conductor ribbon cable with color-keyed connectors, set the drive configuration jumper to CS and connect the drives to the cable as you wish (in terms of physical placement in the computer). If the ribbon cable doesn't have color-keyed connectors, set the jumper for the device connected to the end connector as Master and the drive (if any) connected to the middle connector as Slave.

KEC 7002 IDE Controller card

Yes i have windows 7 with a DC7800 CMT and i put in a IDE controller card The IDE Controller card..i put it in my PCI slot and hooked up the ide card to the card and my hard drive and put the 4 pin power cord into the hard drive..i know the hard drive is getting power but it is not showing up in the hard drive secotion of my computer..i have the jumper set to slave since i have a main SATA hard drive as the main hard drive..im using the IDE as a slave for more space..anyone can help that would be great! Thanks

Why IDE hard drive would be my first question, but your needs might outweigh me asking. There is no Master with SATA. A single EIDE/IDE drive is a Master on the cabling. Here is a link to the proper master/slave issue and the location of such drives on the cabling.
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

Motion controller card need to program PWM or not?

I just want to know about motion controller card (coz may be i will use it)
First, Motion controller card need to program PWM for drive DC motor or not? (If I want to control the dc motor by PWM signals!)
Second, If my motor have encoder (increment) the motion controller card can be read the position or speed directly or not?
Third, Normally motion controller card need Labview for programming or not?
Lastly, Please, could someone give me some example programming or .vi for basic closed-loop dc servo motor ?

bkk,
here are the answers you are looking for
Motion Control boards like the PCI-7344 generate a +/-10 V signal to control DC axes. As they can't provide enough power to drive a motor directly an external power amplifier like the MID-7654 or a 3rd party drive with a +/- 10 V command input is necessary. Typically these power drives generate PWM power signals for the motors.
All NI motion control boards provide inputs for quadrature encoder feedback (position and velocity).
The NI-Motion driver provides a well documented API for LabVIEW, C and other programming languages.
After installing the NI-Motion driver you will find lots of example programs for LabVIEW and C that demonstrate every aspect of the boards' functionality. NI motion controllers run the control loop in hardware so the examples will work for both, closed loop and open loop (stepper motor) applications.
I hope that helps,
Jochen Klier
National Instruments Germany

Calling dll of Leetro MPC08 PCI motion controller card problems.

Hi,
I have been trying to develop an application using Labview 8.5. I need to control a motorized linear stage which uses the Leetro MPC08 PCI motion controller card. The manufacturer gave me example VIs which I configure to call "c:\windows\system32\MPC08.dll". About four months ago, I remembered that i tested them and they seemed to work somehow (but I did not finish the full test since i was busy doing other things). Nevertheless, when I got back to continue my development a few days ago, i just could not get the same old VIs to work. I could only get one library function of the card to work which is the "auto_set" which returns "4" which is the number of axes that the card can control. The next function I need to call is "init_board" but this one keeps returning "-3". The manual indicates that any negative number returned means there has been something wrong. I would guess it is "PCI initialization fails" but honestly do not know for sure. Can anyone help? My computer is a PC running windows XP.
Thanks in advance for any kind help offered.

Hi,
Wrapped VISA call means that the SubVI contains a set of VISA calls.
If you are calling the VI's individually it is possible that the VI's need to pass a reference to each other, so they might not work if run individually. Hard to know without the DLL docs, so to speak. It could be possible that there is no need to pass references between subVI's.
Direct VISA calls are probably not necessary if the device runs with the vendors software. The main goal was to verify functionality with either VISA or vendor app.
Ok I was looking at the Leetro web site, you can forget the VISA stuff as it is a PCI card, duh... you said that at the begining. :-)
The manual says Win2000 or XP. is this being run on two different systems?
Mark
Mark Ramsdale

What HD and Controller Card to Buy for Upgrade?

I've been on OWC looking at the various hard drives and controller cards. My head is swimming. I have a G4 Sawtooth running on OS 9.2. I want to upgrade my hard drive but want to move up to Panther shortly thereafter. Some of the Hitachi products say you need OSX, that I'm afraid if I installed first, would significantly slow down my operating system. Also, I have some software that I would have to use OS 9, as they don't run on OSX, including Photoshop and my Agfa Scanner. Any suggestions on what I should look for?
By the way, their demo on installation is awesome!

Flyingcat, I was at this same point about a year ago, and like you I decided to invest in this G4 and maybe get another 2-3 years before making another decision on a new Mac. Here is what I did in the order I did it.
1. A newer faster HD (with available rebates this was by far the most economical).
2. A RAM increase to 1.5 GB, but keep in mind OS X will see a full 2 gigs.
3. An OS upgrade to Panther, but also keeping a bootable version of OS 9.
4. I upgraded the processor (Sonnet Encore/ST G4 1GHz).
5. A video card upgrade to Radeon 9000 (this was used and purchased from a close friend).
6. A SATA HD and controller card.
Joe
ps. Is the scanner SCSI and which Photoshop are you using.
Power Mac G4 Gigabit Ethernet Mac OS X (10.3.9)

Multiple SATA Controller Cards

In addition to a couple of external firewire drives and an external dual SATA enclosure, I'm considering installing the Sonnet G5 Jive or similar multi-bay internal solution.
I don't see this as presenting much of a problem, but just curious if anyone else has had any issues installing two PCI-X SATA controller cards in their systems...
anyone tried this?

Thanks for the response DaddyPaycheck
That's interesting. I hadn't considered power supply issues; I just assumed that any manufacturer...particularly Sonnet...would have considered a potential problem such as this...(maybe that's a bit naive on my part).
At the same time, I hadn't really done much research on the Jive. I wanted to be certain that two SATA cards wouldn't pose a problem first...
Thanks again

I have an Ipod1 with 3G and an unlimited ATT plan. I want to get an Ipad2 - can I swap SIM cards so that my unlimited service will automatically transfer to the new unit?

I have an Ipod1 with 3G and an unlimited ATT plan. I want to get an Ipad2 - can I swap SIM cards so that my unlimited service will automatically transfer to the new unit?

You don't actually swap the SIM card. For some reason, AT&T doesn't like you to do it that way.
Go to:
www.att.com/ipadlanding
edit payment information link...then update the following two fields:
IMEI:
ICCID:
You get this info from the iPad (1 or 2) select 'Settings' then 'General' then 'About'...
The IMEI and ICCID info is on that screen. No need to swap the SIM cards. This process outlined above transfers service instantly and does NOT change the plan type, billing, user info, or days remaining. Basically anytime an ATT customer wants to move a data plan the ATT iPad web page is all you need. No phone call!
It took me about 3 minutes and worked perfectly.

Swapping Controller cards

Similar Messages

Maybe you are looking for