SWEQADM - Event hanging in status IN PROCESS

We have activated the event queue (SWEQADM) for all our workflows. Now I have discovered that we do have a lot of events which are stuck in status IN PROCESS. When we go to the event queue browser and try to deliver the event we get the following message:
'The event cannot be delivered in status "In Process" '
Do any of you have experience of this? Any ideas on why they are stuck in status IN PROCESS, and how we should be able to process them.

Hello Kicki,
The most likely cause for events to remain in process as you describe is that something goes wrong during the receiver processing. This could either be an error causing a short dump (ST22) or else a basis-related problem, look at SM58 for stuck RFCs or SM13 for update problems.
More clues might be in the events themselves: is it just one event or a particular set of events or do they appear to be random? If the latter is the case, it would point to more towards a basis related problem.
Also, you mentioned that you switched it on for ALL workflows. Any particular reason? As you have already noticed the event queue adds an extra layer into the process which equates to an extra point of failure. Unless you are using it to direct workflows to specific servers, you are probably better off only sending high volume events to the queue.
Hope that helps.
Cheers,
Mike

Similar Messages

Email/print in status "Not processed" when RFQ is published

Hello,
We are running SRM 5.0.
We have set up the event schema for BUS2200 (RFQ) to react on events: PUBLISHED, PUBLISHED_AGAIN etc. And assigned the event schema to RFQ's transaction types, eg BID.
However, when an RFQ is published, the email is not sent to vendor (whose default medium is MAI) or printed on vendor's default printer (if the medium is set to PRN). The output log under bidder/bids tab shows something like :
Status: Not processed
Medium: Print
When I clicked on the action button "Output pushbutton", the status would be changed to "Successful" and the email would be sent or the print job would be printed then.
I have checked the PPTTRIGG table and all the entries in there are of DISPATCH = 1 or 4. Not 3, which seems to indicate an "immediate processing".
My question is how I would configure the system so that the email/print when the RFQ is published could be processed immediately.
Thanks.

Hello Masa,
I realized it as well. I was then a little puzzled why SRM didn't allow "immediate processing" for the "processing time" parameter in the action definition. Do you know if there is a particular reason for that?
Thanks,

Workflow hanged- Background Task in Process.

Hi All,
Workflow hanged at background task with status in Process due to a dump…we change the logic now.
How I can restart this task again?
I checked in SWPC its empty.
Thanks,
KP

Yes, SWI2_DIAG has a Restart Workflow' button.
Did you try it already?
Despite what the button name suggests, it 'resumes' the workflow from the current step
(it doesn't 'restart' from scratch).
cheers
Paul

Cancelamento de NF-e parado (batch status 05, process status 02)

Bom dia pessoal,
Ontem tivemos um problema no GRC/PI de um cliente, onde por alguma razão o certificado estava sendo rejeitado. Depois de vários problemas causados por isso, foi resetado o j2ee e o sistema voltou a operar normalmente.
As sequelas disso foram duas notas para as quais foi solicitado o cancelamento, agora elas estão com status de processamento 02 (Sent to Signature Service) e batch status 05 (Result Received).
Seguindo uma orientação para um caso parecido (),
peguei os MsgIDs das mensagens dessas NFs na /xnfe/acknowledg (ambas com SIGNC), encontrei-as no SXI_MONITOR do PI, onde elas são listadas 2x cada, com os seguintes status
1 - Status = Transfer to Process Engine (, Ack. Status = branco
2 - Status = Processed Successfully, Ack. Status = Still awaiting acknowledgment (bola verde com interrogação)
Ao tentar dar restart nas mensagens, recebo a seguinte mensagem de erro:
You cannot restart XML message E07AFA5FD584CEF1B15C3C4A927627EC with this status/type
Message no. XMS_ADM085
Diagnosis
You want to reschedule an XML message that has already been processed (Restart). However, the XML message status or type does not permit a restart.
System Response
You can only restart asynchronous XML messages.
Furthermore, you can only reschedule XML messages with errors. You cannot restart correctly processed XML messages or XML messages with the status Being Processed.
Tem algo que possa ser feito sem ter que alterar tabelas?
Como a equipe responsável pelo PI/GRC fica fora do BR, é bem complicado conseguir autorização para qquer coisa nesse sentido em PRD.
ps.: Agora cliquei no "Expand all messages", para cada um dos MsgIDs, apareceram 2 novas linhas, uma com status = Scheduled (bandeira verde) e outra com status Scheduled for Outbound Processing (seta preta), ambos com o awaiting ack.
=> SMQ1 e SMQ2 ambas sem entradas.
Obrigado!
Eduardo Hartmann

Eduardo,
O NFe type = 2 (cancelamento)?
Se sim, me parece que o pedido de cancelamento foi enviado pra assinatura e nao teve resposta, provavelmente devido ao fato de o J2EE estar fora. Nesse caso, o batch status é irrelevante (ele só é relevante pro processo de envio de NFe, não pra cancelamento/inutilização).
O "correto" seria vc identificar onde a mensagem de assinatura parou (i.e. se em alguma fila - SMQ1/SMQ2, se tem q restartar o BPM etc.). Mas como o passo de assinatura é stateless, diferentemente do processamento da SEFAZ, vc poderia simplesmente "marretar" um status de erro de assinatura de cancelamento na /xnfe/nfe_hist (verifique o valor apropriado do error status no domínio do campo) e restartar a assinatura do cancelamento pelo monitor de NFe do GRC, aba de erro de assinatura.
Abs,
Henrique.

Print Preview of PO with message status as "Processed"

Hello,
I need to make available the print preview of Purchase Order even when the Processing status of output is "Processed".
Normally the print preview works when the status is "Processing" or when there are still print relevent changes existing in PO. When the message is output by ME9F, there are no more print relevent canges and SAP does not allow preview option in PO. I want to make this functionality available.
Any solution?
CMV

Hi!
You can check the table NAST (field VSTAT) for the statuses.
Application 'EF' for PO.
Objkey is the PO number.
Regards
Tamá

SRM 7.0 Purchase Order Response always in status "In process" after confirm

Hello experts,
this problem is similar to the thread [SRM-SUS Purchase Order Response always "In Status"; which has been not finally responded.
My problem exists in an environment without SUS.
When a buyer confirms a PO response (POR) without any change, the system generates a new PO response with status "In process". This new POR has also to be confirmed or rejected but the system generates again a new PO response with status "In process".
So we have a very nice loop for the purchaser without escape!
We are on SRM 7.0 SP07. The other thread mentioned that SAP will create some OSS notes, but I found nothing about this problem.
Any ideas?
Regards
Joe

Hi Gurus.
I want to share my experience with this case.
We have the same scenario, Confirm PO, the result is PO confirmed, but we receive a response from ECC and this Confirmed PO changes its status to "In Process" / "En Tratamiento".
The new relevant information is that we added 2 new fields to the item PO, these fields are filled ok and sent to ECC.
In a first time these new fields were lost due to the response from ECC. To avoid this situation I implemented the BADI BBP_DOC_CHANGE_BADI for BUS2230, and method BBP_SUSPO_CHANGE to copy from the BBP_PDISC (Object BUS2230) rows the values to the new rows in the same table BBP_PDISC (Object BUS2201).
With this change the new documents are confirmed directly and not changed to "In Process"/ "En tratamiento".
That was my experience, now I have a question...
In the correct business process for SAP SRM SUS when you confirm full a PO...
* this will be blocked or no?
* Can be modified the confirmed items?
* This depends of customizing?

Jdbc sender adapter hangs and starts showing "Processing Started" forever

Dear ,
We are facing some issues with jdbc sender adapter channel on production system
Environment : XI 3.0 SP 20 + HP-UX 11.23 ia64 + Oracle 10.2
Sometimes it hangs and starts showing "Processing Started" forever on communication channel monitoring .
There is no error log for this.
If i stop it and then start it , no use.
If i copied this to a new one then it works.
I have found few SAP note like 1078420,1083488 , but my system is already at higher patch level.
Can you please advise me something as we are facing in production frequently.
Regards,
Sandeep

Hi Sandeep,
This problem even we too faced in our project and thought of many stupid things finally found that the JDBC adapter is LOCKED.
Check in the Visual Admin >Cluster> "LOCKING ADAPTER"
we get a option of Display Locks .Check for an entry with
NAME : $XIDBAD.JDBC2XI
reset the locks and restart the CC ,now it works fine.
Note 1083488 - XI FTP/JDBC sender channel stop polling indefinitely(04/04S)
Thanks
Sudharshan

BPM Status "In Process" - Message reached ECC successfully ??!!!

Hi,
I need help to resolve one issue which we are facing : (this is kinda strange)
==========================================================================
We are using a BPM in one of our scenario where acknowledgements are sent in and out from PI to ECC. The BPM is relatively complex.
The issue we are facing is : -
The BPM shows status "In Process" but the messages have reached ECC and the functional team has confirmed the receipt of the message. All the tables / databases are updated as desired. We were yet to receive the response from ECC but strangely the BPM is not completed but the message has moved out of PI to ECC and updated the tables!!
My question is : - How come the messages reached ECC even though it showed that the BPM is not completed?
==========================================================================
Action points which I have taken : -
1.) I have digged in sxmb_moni_bpe and went through the messages in the payload couldn't find anything there which could have answered my question.
2.) Matched the data and went through all the message flow comparing the time stamp - didnt find much here too!
3.) The graphical message flow shows "Response from ECC" - in Wait state and a white block but still the messages got updated. Found it really strange!! .. If the BPM does not get completed, the messages should not move out!!
============================================================================
workaround :-
1.) I thought of putting a wait step and an exception that if the messages do not reach PI within the stipulated time, it will throw and error in PI. But still the question needs to be answered as to "How come the messages reached ECC even though it showed that the BPM is not completed?"
Kindly suggest.

I didnt find anything much there .. and moreover it is a Production system where we faced the issue so anyway I did nt have access to it. We have confimed from ECC functional team on the same and have logically deleted the process from PI.
Thanks anyway!

WebLogic hangs around after shutdown process appears to complete - Message Driven Bean related

On my current project we have some Ant scripts that automatically
start and stop WebLogic. The stop script equates to (not exactly but
close enough):
java weblogic.Admin -url localhost:8001 -password password -username
username SHUTDOWN
WebLogic is start and shutdown for each system module. All modules
use the exact same script for these two actions. Some of the modules
use Message Driven Beans and consequently, since these use JMS, a
JMSxxx.dat file is generated in the jms_store directory. As part of
the cleanup process the jms_store directory and all files in it are to
be deleted AFTER WebLogic shuts down.
The shutdown process works fine in all cases where JMS is not used and
in all cases where JMS IS used but there are NO message driven beans.
However, when there is a message driven bean the server does not shut
down in a timely manner, sometimes not at all (no error messages are
produced), and the JMSxx.dat file
remains locked. Consequently, all of the tests run via the ant script
for modules come to a grinding halt (i.e. environment could not be
cleaned so further tests would be skewed).
Can anyone shed some light on a definitive order of events during
WebLogic's shutdown process? What is the best way to test for the
server being up? I know there is a ping utility for weblogic - should
this be used or should a connection to a JNDI or JMS listening port do
the trick? Any other ideas would be welcome.
Thanks in advance,
Mark

On my current project we have some Ant scripts that automatically
start and stop WebLogic. The stop script equates to (not exactly but
close enough):
java weblogic.Admin -url localhost:8001 -password password -username
username SHUTDOWN
WebLogic is start and shutdown for each system module. All modules
use the exact same script for these two actions. Some of the modules
use Message Driven Beans and consequently, since these use JMS, a
JMSxxx.dat file is generated in the jms_store directory. As part of
the cleanup process the jms_store directory and all files in it are to
be deleted AFTER WebLogic shuts down.
The shutdown process works fine in all cases where JMS is not used and
in all cases where JMS IS used but there are NO message driven beans.
However, when there is a message driven bean the server does not shut
down in a timely manner, sometimes not at all (no error messages are
produced), and the JMSxx.dat file
remains locked. Consequently, all of the tests run via the ant script
for modules come to a grinding halt (i.e. environment could not be
cleaned so further tests would be skewed).
Can anyone shed some light on a definitive order of events during
WebLogic's shutdown process? What is the best way to test for the
server being up? I know there is a ping utility for weblogic - should
this be used or should a connection to a JNDI or JMS listening port do
the trick? Any other ideas would be welcome.
Thanks in advance,
Mark

Workflow step in status "In Process"

Hi Friends,
I am working on SAPXI support project.
Actually i have an issue related with BPM, there is a workflow(wk) which is completed but the one of the step in this wk is status "In process", but i can see all the steps in this wk are either completed or logically deleted except one step which is called as "Main Process Block".
Due to this there are countinues CCMS alerts genereted in TC RZ20. So kindly suggested me on how to complete this Step either i have to delete or complete or anyother solution.
Please dont give me any blogs or links, kindly suggest with your experince in Support project.
Regards
Sai

Hi Sai,
goto tcode SWIA and enter the work Item ID and click on Complete mannually.
Thanks!

Status of process chain

hi all,
This is the scenario. I have a badi in ecc in which i save the new projects and after saving a project it triggers a job in ecc ,which in turns trigger the process chain.When i try to save several projects in ecc in quick succession, say 3 projects A,B,C then there are 3 jobs which are active in ecc,which inturns triggers the process chain 3 times and hence the p.c gets locked and fails.
In the badi, we had rfc fm which checks the status of the process chain whether its ACTIVE from rspcprocesslog table and then if the status become to G:successfully completed, the second job shold trigger.however its not working.
in the rspcprocesslog(BI side), we find that the status field in the table is having only two values F:completed or G:successsfully completed, whereas other values such as ACTIVE ,cancelled are not getting stored.
so i would like to know
1. whether this table holds only G or F values and why the status like Active or cancelled is not gettin g stored.?
2. apart from these tables what is the method by which i can know the status of process chain or status of thelast process of the chain can be found.?
3. is there any way to check for the information we get in sm 37 job log in BI side for the last process present in the process chain? *is the job log stored in some table ,if so what is the table name?*
so can anyone please suggest to make the second job in ecc to get scheduled only when the process chain which got triggered for the first job is completed other than the two mentioned(rspcprocesslog, and job log)?

Hi,
You can find the necessary logs & status of the process chains in the RSPCLOGCHAIN table.
ANALYZED_STATUS field stores the values of process status.
G -> Completed
R -> Ended with errors
A -> Active
X -> Cancelled.
Many thanks,
Arda.

WS20000075: work item of 1st release step stays in status In process

Hi All,
I have activated and set up standard flow WS20000075 but the work item of 1st release (PO release strategy with 3 levels) step stays in status In process. The work item for the 2nd and 3rd release step are completed as expected.
What could cause only the work item of the 1st release step to stay In process?
Thanks a lot in advance

Hi,
I cannot see in what field the release code is filled in EKKO.
See here SWEL after 1st release:
And SWEL after 2nd release:
EKKO after 1st release
EKKO after 2nd release
release strat
Release strategy

How to Implement HTTP Request Status Code Processing

I actually have two questions. First, I wondering how to add multiple status code processing to an http request. Secondly, I was wondering how to go about using alternate http requests to different servers in case the primary server is down. What kind of parameter would the program use to determine that the server is unavailable and switch to another server??
Currently, the program I've written calls an rdf server (http://www.rdfabout.com/sparql) using a sparql query,
the server returns an xml string, the program parses it, and calculates numbers
from the string. The program works, but the problem is that the server is down occasionally.
When the server is down, we need to add calls to another server to
increase reliability. So, the next task is to call this server:
http://www.melissadata.com/lookups/ZipDemo2000.asp
I need to do exactly the same things I did with the rdf server. The
difference will be constructing a request and a bit different parsing of
the response.
current SPARQL query is defined as follows:
PREFIX dc: <http://purl.org/dc/elements/1.1/>
PREFIX census: <http://www.rdfabout.com/rdf/schema/census/>
PREFIX census1: <tag:govshare.info,2005:rdf/census/details/100pct/>
DESCRIBE ?table WHERE {
<http://www.rdfabout.com/rdf/usgov/geo/census/zcta/90292> census:details
?details .
?details census1:totalPopulation ?table .
?table dc:title "SEX BY AGE (P012001)" .
}current HTTP Request is defined as follows:
import java.net.*;
import java.net.URL;
import java.net.URLConnection;
import java.io.*;
import java.io.DataOutputStream;
import java.io.BufferedReader;
import java.io.StringReader;
import java.io.InputStreamReader;
import java.io.PrintStream;
import java.util.Scanner;
import java.util.regex.Matcher;
import java.util.regex.Pattern;
import java.util.Arrays;
public class MyConnection
     static Scanner sc = new Scanner(System.in);//allows user to input zipcode
    public static void main(String[] args) throws Exception
         int zip;//zipcode is declared as integer format
        //User defines zip through input
        //proceed to put SPARQL query into string, which is then used to call the server
        String requestPart1 =
        "query=PREFIX+dc%3A++%3Chttp%3A%2F%2Fpurl.org%2Fdc%2Felements%2F1.1%2F%3E+%0D%0APREFIX+census%3A+%3Chttp%3A%2F%2Fwww.rdfabout.com%2Frdf%2Fschema%2Fcensus%2F%3E+%0D%0APREFIX+census1%3A+%3Ctag%3Agovshare.info%2C2005%3Ardf%2Fcensus%2Fdetails%2F100pct%2F%3E+%0D%0A%0D%0ADESCRIBE+%3Ftable+WHERE+%7B+%0D%0A+%3Chttp%3A%2F%2Fwww.rdfabout.com%2Frdf%2Fusgov%2Fgeo%2Fcensus%2Fzcta%2F";
        String requestPart2 = "" + zip; // zipcode is transformed from int to string format and plugged into SPARQL query here
        String requestPart3 =
        "%3E+census%3Adetails+%3Fdetails+.+%0D%0A+%3Fdetails+census1%3AtotalPopulation+%3Ftable+.+%0D%0A+%3Ftable+dc%3Atitle+%22SEX+BY+AGE+%28P012001%29%22+.+%0D%0A%7D%0D%0A&outputMimeType=text%2Fxml";
        String response = "";
        URL url = new URL("http://www.rdfabout.com/sparql");//designates server to connect to
        URLConnection conn = url.openConnection();//opens connection to server
        // Set connection parameters.
        conn.setDoInput (true);
        conn.setDoOutput (true);
        conn.setUseCaches (false);
        // Make server believe we are form data
        conn.setRequestProperty("Content-Type","application/x-www-form-urlencoded");
        DataOutputStream out = new DataOutputStream (conn.getOutputStream ());
        // Write out the bytes of the content string to the stream.
        out.writeBytes(requestPart1 + requestPart2 + requestPart3);
        out.flush ();
        out.close ();
        // Read response from the input stream.
        BufferedReader in = new BufferedReader (new InputStreamReader(conn.getInputStream ()));
        String temp;
        while ((temp = in.readLine()) != null)
             response += temp + "\n";
        temp = null;
        in.close ();
        //parsing stuff is taken care of after here
}What remains now is to:
1) add status code processing: notify if the server is not available, ect.
2) add ability to connect to additional server if primary server is down.
I'm thinking an if/else statement, which I've tried a few different ways,
but I don't quite know how to implement that...Also trying to add the
status code processing/error handling, but I'm not sure how to do that
for multiple/different errors, such as 404, 503, 504, ect.. try/catch statements?
So yeah, just been scratching my head on this trying to figure out how to work it..
If you can help me out on this, I've been going nuts trying to figure this out...

I think your issue comes form the fact that you are not casting URLConnection to HttpURLConnection.
Doing the cast would allow you to use getResponseCode() - among other methods - and test for a response different than 200.
Read: [http://mindprod.com/jgloss/urlconnection.html|http://mindprod.com/jgloss/urlconnection.html]

WF: Object DECISION Method PROCESS - stays in status in process forever

Dear Friend,
Could you, please, give me any ideas why Workflow Task based on business objects/method DECISION->PROCESS stays in status in process?
It happens after upgrade to ERP2005 from 4.6c. In old version it works perfectly.
Thanks a lot for help.

Hi,
If a Workitem has Status "In Process" then it means it is under execution and it is not completed. however it might get completed and the status is still can be "In Process". The reason for this would be the Workitem might have gone in Deadline monitoring. Check the Workflow Task whether any deadline is assigned or not. I guess it got assigned in your case. And another important thing is there must be a background program that is scheduled which takes care of such deadline monitoring Tasks. Check whether this program is ticked or not in transaction SWU3. So altogether you have to check two things.
hope this helps you.
thanks,
sksingh

Workflow status 'in process'

Hello All!
I've created workflow with only task step. Workflow started and has status 'in process', then task completed but workflow still has status 'in process'. As i understand i need workflow status 'Completed' after task execution.
Where can i set up this?
Many thanks in advance!

Please check SWU3 is properly configured.
Also check for any Dump in ST22.
Thanks
Arghadip

SWEQADM - Event hanging in status IN PROCESS

Similar Messages

Maybe you are looking for