Switch 3750x not support ip routing command

Dear all,
I have problem with Switch 3750x, with intervlan configuration, while I try to enter command:
switch(config)ip routing
it show invalid message.
switch(config-if)no switchport
it so message inject with this command. what is problem it is a new switch without previous configuration.

CoreS1#show ver
CoreS1#show version
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE5,                                                                                 RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 09-Feb-12 18:14 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000
ROM: Bootstrap program is C3750E boot loader
BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(58r)SE1, RELEASE SOFTW                                                                                ARE (fc1)
CoreS1 uptime is 3 minutes
System returned to ROM by power-on
System image file is "flash:/c3750e-universalk9-mz.122-55.SE5/c3750e-universalk9                                                                                -mz.122-55.SE5.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Level: lanbase
License Type: Permanent
Next reload license Level: lanbase
cisco WS-C3750X-24 (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1827P037
Last reset from power-on
3 Virtual Ethernet interfaces
1 FastEthernet interface
28 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : 58:F3:9C:1B:73:00
Motherboard assembly number     : 73-12530-11
Motherboard serial number       : FDO182604V9
Model revision number           : A0
Motherboard revision number     : A0
Model number                    : WS-C3750X-24T-L
Daughterboard assembly number   : 800-32727-03
Daughterboard serial number     : FDO182616NC
System serial number            : FDO1827P037
Top Assembly Part Number        : 800-31327-09
Top Assembly Revision Number    : C0
Version ID                      : V06
CLEI Code Number                : CMMPM00DRA
Hardware Board Revision Number : 0x05
Switch Ports Model              SW Version            SW Image
*    1 30    WS-C3750X-24       12.2(55)SE5           C3750E-UNIVERSALK9-M
Configuration register is 0xF
CoreS1#show license
Index 1 Feature: ipservices
        Period left: 8 weeks 4 days
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
        License Priority: None
        License Count: Non-Counted
Index 2 Feature: ipbase
        Period left: 0 minute 0 second
Index 3 Feature: lanbase
        Period left: Life time
        License Type: Permanent
        License State: Active, In Use
        License Priority: Medium
        License Count: Non-Counted

Similar Messages

I have noticed that Safari does not support some HTML commands on apple operating systems. Can anyone help with this issue please?

I have noticed that Safari does not support some HTML commands on this operating platform. Can anybody throw any light on this issue please?

Examples.

3750 metro series switch does not support dot1q trunking?

Folks,
I have a 3750 metro series switch and i am trying to use it to do inter vlan routing. I do not see an option for "encapsulation dot1q" under sub interface?? why is it not supported??
Thanks

Narvin,
if you want inter-vlan routing, the interface Vlan nn itself specify vlan.I think you confuse with router subinterface where you must specify what Vlan a subinterface must use ( and encaps type ). Encaps type ( dot1q or ISL ) is used at trunk level, and whatever trunk use you can do intervlan routing using vlan interface.
maurizio

3750 metro switch does not support Dot1q??

Folks,
I have a 3750 metro series switch and i am trying to use it to do inter vlan routing. I do not see an option for "encapsulation dot1q" under sub interface?? why is it not supported??
Thanks

Navin,
This question has been answered under "Network Infrastructure".
Josef.

Version 03.03.00.XO - MLS QOS not supported

Hi All,
Anyone face the same problem with the following IOS Version?
MLS QOS is not supported in global command.
Switch#sh ver
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500es8-UNIVERSALK9-M), Version 03.03.00.XO RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 14-Aug-13 07:26 by prod_rel_team
Cisco IOS-XE software, Copyright (c) 2005-2013 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: 15.1(1r)SG2
Switch uptime is 6 minutes
System returned to ROM by power-on
Running default software
Jawa Revision 3, RadTrooper Revision 0x0.0x41, Conan Revision 0x1449
Last reload reason: power-on
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Information for 'WS-X45-SUP8-E'
License Level: entservices Type: Permanent
Next reboot license Level: entservices
cisco WS-C4506-E (P5040) processor (revision 2) with 4194304K bytes of physical memory.
Processor board ID FXS1812Q346
P5040 CPU at 2.2GHz, Supervisor 8-E
Last reset from PowerUp
1 Virtual Ethernet interface
20 Ten Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
Configuration register is 0x2101
SWITCH(config)#mls qos
                     ^
% Invalid input detected at '^' marker.
SWITCH(config)#
SWITCH(config)#?
Configure commands:
aaa                         Authentication, Authorization and Accounting.
access-list                 Add an access list entry
access-session              Access Sesion Global Configuration Commands
agent-server                Modify DNS server properties
alias                       Create command alias
ancp                        Configure ANCP
archive                     Archive the configuration
arp                         Set a static ARP entry
async-bootp                 Modify system bootp parameters
audit                       Router Audit
authentication              Auth Manager Global Configuration Commands
auto                        Configure Automation
banner                      Define a login banner
beep                        Configure BEEP (Blocks Extensible Exchange
                              Protocol)
bfd                         BFD configuration commands
bfd-template                BFD template configuration
boot                        Modify system boot parameters
bridge                      Bridge Group.
buffers                     Adjust system buffer pool parameters
bulkstat                    Bulkstat Application
call-home                   Enter call-home configuration mode
cdp                         Global CDP configuration subcommands
cef                         Cisco Express Forwarding
cisp                        Set CISP parameters
class-map                   Configure CPL Class Map
clns                        Global CLNS configuration subcommands
clock                       Configure time-of-day clock
cluster                     Cluster configuration commands
cns                         CNS agents
comet-server                Configure comet-server properties
config-register             Define the configuration register
configuration               Configuration access
control-plane               Configure control plane services
crypto                      Encryption module
cts                         Cisco Trusted Security commands
default                     Set a command to its defaults
default-value               Default character-bits values
define                      interface range macro definition
device-sensor               IOS Sensor Commands
diagnostic                  Configure diagnostic information
dns-server                  Modify DNS server properties
dnsix-dmdp                  Provide DMDP service for DNSIX
dnsix-nat                   Provide DNSIX service for audit trails
do-exec                     To run exec commands in config mode
dot1x                       IEEE 802.1X Global Configuration Commands
downward-compatible-config Generate a configuration compatible with older
                              software
eap                         EAP Global Configuration Commands
emm                         Specify pre-loading of MDF
enable                      Modify enable password parameters
end                         Exit from configure mode
energywise                  EnergyWise Global Configuration Commands
epm                         EPM Global Configuration Commands
errdisable                  Error disable
ethernet                    Ethernet configuration
event                       Event related configuration commands
exception                   Exception handling
exit                        Exit from configure mode
fallback                    Fallback configuration commands
fhrp                        Configure First Hop Redundancy Protocols
file                        Adjust file system parameters
fips                        FIPS mode after next reload
flow                        Global Flow configuration subcommands
format                      Format the output
global-address-family       Enter address-family base routing topology mode
help                        Description of the interactive help system
hostname                    Set system's network name
hw-module                   Apply command (e.g. shutdown) to specified
                              hardware target
hw-module                   Control of individual components in the system
hw-switch                   Control of individual components in the switch
id-manager                  ID Pool Manager
identity                    Identity Configuration Commands
infra-test                  Configure end2end properties
interface                   Select an interface to configure
ip                          Global IP configuration subcommands
ipc                         Configure IPC system
ipv6                        Global IPv6 configuration commands
isis                        Global ISIS configuration subcommands
issu                        no description
key                         Key management
kron                        Kron interval Facility
l2                          Layer 2
l2protocol-tunnel           Tunnel Layer2 protocols
lacp                        LACP configuration
li-view                     LI View
license                     Configure License
line                        Configure a terminal line
link                        Enable Link State Tracking feature
lldp                        Global LLDP configuration subcommands
location                    Global location configuration commands
logging                     Modify message logging facilities
login                       Enable secure login checking
mab                         MAC Authentication Bypass Global Configuration
                              Commands
mac                         Global MAC configuration subcommands
macro                       Macro configuration
media-proxy                 Global media proxy configuration
mediatrace                  Mediatrace Application
memory                      Configure memory management
metadata                    Metadata Application
mka                         MACsec Key Agreement (MKA) configuration
module                      Module
monitor                     Monitoring different system events
mvr                         Enable/Disable MVR on the switch
netconf                     Configure NETCONF
Thank you.

Hi,
QOS implementation has radically changed since the advent of
sup-7 & later
You no longer set mls qos as qos is on the engine by default.
Please see the following links
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/white_paper_c11-539588.html
"Ingress QoS: Default Actions
First and foremost, QoS does not need to be enabled on the Supervisor Engine, it is on by default in compliance with the MQC construct.
When a packet arrives at an interface, there are two options to take into consideration: is there a policy attached or not? If the packet arrives with or without a marking and there is not a policy attached to the interface, packets will flow through the switch untouched. There are no questions as to where the packet came from or if it has a valid marking. If the packet arrives with or without a marking, and a policy is attached to the interface, the packet will only then be subject to the policy classification."
And the config guide
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/15-1/XE_330SG/configuration/guide/config/qos_mrg.html#wp1461453
Hope this helps
Regards
Alex

Distributed multicast routing command not working on Catalyst 3850 switch

Hi Cisco community,
I was wondering if there is a known problem as to why the ip multicast-routing [distributed] option is not available on the Cat 3850 platforms
global command " ip multicast-routing " is accepted
the configuration guide named:
IP Multicast Routing Configuration Guide, Cisco IOS XE Release 3SE (Catalyst 3850 Switches)
First Published: January 29, 2013
Last Modified: October 22, 2013
explains that this option "key word" [distributed] should be available>
Enables IP multicast routing.
ip multicast-routing [distributed]
Device(config)# ip multicast-routing distributed
=============== Here is what i have and see =========
Config attempt
============
CAT-3850-1(config)#ip multicast-routing distributed
^
Show command:
========
CAT-3850-1#show ip multicast
Multicast Routing: enabled
Multicast Multipath: disabled
Multicast Route limit: No limit
Multicast Fallback group mode: Sparse
Number of multicast boundaries configured with filter-autorp option: 0
Software:
========
Cisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M),
Version 03.03.03SE RELEASE SOFTWARE (fc2)
License rights:
============
CAT-3850-1#sh license right-to-use
Slot# License name Type Count Period left
1 ipservices permanent N/A Lifetime
1 apcount adder 10 Lifetime
License Level on Reboot: ipservices
Slot# License name Type Count Period left
2 ipservices permanent N/A Lifetime
2 apcount adder 10 Lifetime
License Level on Reboot: ipservices
Any hints and help would be greately appreciated.
Many thanks in advance
Markus

Hi Reza,
Thank you for your quick reply, and for putting the record staright. As such, a helpful rating was provided
PS: Feel free to help me one more time if you happend to know folllow on this query :)>
I guess that the disributed function has been included in the standard mulitcast routing command because the key word is no longer needed. Or perhaps this platform does not support this at all.#
Once again , thank you for your help above.
Best regards

WbAdmin Delete Backup command not supported in 8.1 Pro x64

Hello
I've searched for how to delete specific backups that I've created using the elevated Power Shell command "wbAdmin start backup -backupTarget:E: -include:C: -allCritical -quiet" but I've run into a roadblock.
The problem is that none
of the "wbadmin delete xxx" commands are actually supported in Win8.1 Pro 64-bit (6.3, Build 9600). If I type "wbadmin delete /?", I get:
---- Commands Supported ----
DELETE CATALOG                     -- Deletes the backup catalog.
DELETE SYSTEMSTATEBACKUP -- Deletes one or more system state backups.
DELETE BACKUP                       -- Deletes one or more backups.
However, when I try to use ANY delete command (for example, to delete a specific backup version that was identified using "Wbadmin get versions"), I get this error:
PS C:\WINDOWS\system32> wbadmin delete backup -version:06/26/2014-07:29
wbadmin 1.0 - Backup command-line tool
(C) Copyright 2013 Microsoft Corporation. All rights reserved.
Warning: The DELETE BACKUP command is not supported in this version of Windows.
The operation ended before completion.
The same thing happens if I use -deleteOldest, with or without the -backupTarget switch.
Does anyone know why the Delete command is not available on 8.1? Is there a patch, workaround or alternate method of deleting specific backup images?

Yolanda, thank you for confirming the issue and for pointing me to a solution. I really appreciate it!
I have looked at the cmdlet reference page tried to use the commands but it appears that they do not work on my system. For example:
PS C:\WINDOWS\system32> remove-wbcatalog
remove-wbcatalog : The term 'remove-wbcatalog' is not recognized as the name of a cmdlet, function, script file, or
operable program. Check the spelling of the name, or if a path was included, verify that the path is correct and try
again.
At line:1 char:1
+ remove-wbcatalog
+ ~~~~~~~~~~~~~~~~
    + CategoryInfo          : ObjectNotFound: (remove-wbcatalog:String) [], CommandNotFoundException
    + FullyQualifiedErrorId : CommandNotFoundException
Also, if I type the help command listed on the reference page, get-help -module windowsserverbackup, the only reponse is a blank command prompt. Do I need to install the windowsserverbackup functionality separately? It does not seem
to be built-in.

WRT54GS "Router Not Supported".

Hello. I have a WRT54GS V.6. I have had it for quite a long time, but just yesterday it stopped giving internet to its wired connection. The wireless connection was working fine. I reset the router (holding the button in for thirty seconds and planned on making a new network). Everytime now it tells me: "Router Not Supported". I looked around the support here, and ended up downloading the firmware upgrade and upgraded the router, reset it once again, and tried once more. Same problem. "Router Not Supported". The power light is on. The WLAN light is on, the Ethernet Port 1 light is on, and the Internet light is blinking. So it IS recieving the signals. I don't understand what's wrong. I have no internet connectivity through the router, either.
Can someone help me?

Further browsing of the forums, and I came across this:
Step 1 : You should just connect the router to main wired computer from ( port 1,2,3,4). No need to connect the dsl modem in this step .
Step 2 : hard reset the router It seems that we will have to reset the device back to the factory defaults. Kindly follow these steps to reset the device:- - While the device is 'ON', press the reset button on the back panel of the device using a pointed object and keep it held for about 60 seconds. - You will notice that the power light on the device would start blinking, indicating that it is being reset. - After 60 seconds release the reset button and switch 'OFF' the Linksys device and wait for 10 seconds and then switch it 'ON' again. - Let the power light on the device stabilize.
Step 3 : wireless settings. Please access the setup page of the router by launching an Internet Explorer and type on the address bar, 192.168.1.1 and press enter. When it prompts for the username and password, leave the username field empty and provide password as admin all in lower cases and then click on ok. Click on the Wireless tab - Here Wireless Network mode should be mixed - Provide any new name in the Wireless Network Name (SSID) box, all in lower cases without any spaces in between. Do not use any old name - Set wireless channel to 11 - And wireless SSID broadcast should be Enabled and then click on save settings.
Step 4 : wireless security
1. When the router's setup page appears, please click on the Wireless tab.
2. When the Wireless area appears, click on the Wireless Security sub tab.
3. When the Wireless Security area appears, select WEP under Security Mode dropdown.
4. Encryption should be set to 64 bits 10 hex digits.
5. Skip the Passphrase box.
6. In the WEP Key1 box, type in a phone number (just the numbers no spaces or dashes) that you can remember in the box.
7. Make a note of these 10 numbers; this would be your wireless network's key.
8. Leave the key 2, key 3 and key 4 boxes blank, and then click on the Save Settings button.
Step 5 : On the 192.168.1.1 set up page of the router , please click on the set up tab . In that you will find an option as local ip address 192.168.1.1 . Please change that to 10.10.10.1 and then hit save settings at the bottom. Once setting's are saved close that page.
Step 6 : confirmation of the physical connection. You should connected the modem router ( internet port ) to main wired computer ( port 1,2,3,4). Now switch OFF both your modem and the router. Switch ON the modem first and wait for about 40 seconds and only then switch on router. At the end of the step 6 try going online from the wired computer . If you are not able to go online from the wired computer than do the step 7
Step 7 : Please access the setup page of the router by launching an Internet Explorer and type on the address bar, 10.10.10.1 and press enter. When it prompts for the username and password, leave the username field empty and provide password as admin all in lower cases and then click on ok. On the main setup page select the Internet Connection Type as PPPoE. - Then provide the username and password provided by your ISP (Internet service provider) for your connection. (Example: [email protected]) - For MTU select Manual from the drop down box and set the MTU size to 1250. - Select the Keep Alive option and choose the redial period as 30 sec
(Originally in BTB's post)
And it worked for me. :] So my problem is solved.

No 'ip routing' command on switch and yet intervlan routing.

Hi,
In my companies 4500 switch I see there is intervlan routing configured for the 4 Vlans it has but I do not see any 'ip routing' command on it
to enable routing on the switch. Can a switch route even though the command isnt there?

Ran the 'show run all' command and it was there. Thought '
sh run | i ip' would display it but didn't.
Thanks for the command.
We just turned enterprise. I keep forgetting that.

Dot1x mac-auth-byass not supported on 2950 switches

Hi all
I have 2950-24 and 2950SX-24 switches. I upgraded them to the Latest IOS version availlable on cisco site(12.1(22)EA11).
We deployed the mac authentication bypass technology in our organization. The problem is the commands (dot1x mac-auth-bypass) and (dot1x critical) are not supported in this version.
How can we solve this issue. I have many switches having this problem
I appreciate your quick response and thanks on advance.
Thanks

Dear Sir
Are you sure. why it is not supported on 2950 and it is supported on 2940 platforms?
check the below link please. I want to know why cisco doesn't support these important features on this 2950 platform.
http://www.cisco.com/en/US/docs/switches/lan/catalyst2950/software/release/12.1_22_ea11/release/notes/OL14991.html#wp1000099
Thanks in advance,

QOS: egress police command not supported in non-leaf classes

Hello,
I have issue with egress policers on EFP (Service instance).
When configure two egress policers on EFPs (on one physical interface), I received a message:
ME-3600X(config-if-srv)#service-policy output VLAN-50M
QOS: egress police command not supported in non-leaf classes
QoS: Policy attachment failed for policymap VLAN-50M
The configuration looks easy:
policy-map VLAN-50M
class VLAN
police cir 50000000
exceed-action drop
class-map match-all VLAN
match protocol ip
interface GigabitEthernet0/11
description TEST
switchport trunk allowed vlan none
switchport mode trunk
mtu 1998
load-interval 30
service instance 199 ethernet
encapsulation dot1q 199
rewrite ingress tag pop 1 symmetric
service-policy output VLAN-50M
xconnect 82.119.245.231 3291 encapsulation mpls
service instance 500 ethernet
description L2MNG-SWITCHE
encapsulation dot1q 500
rewrite ingress tag pop 1 symmetric
bridge-domain 500
I tried to attach the same policy-map to Service Instance 500, with the messages above mentioned.
I am not sure if this is correct behaviour, and what means term "non-leaf class".
IOS version is 15.2(4)S2 with AdvancedMetroIPAccess.
Best regards,
Josef

Platform supports three level hierarchy - Port, VLAN and Class.
Class is the leaf level.
Queuing is done only at the leaf level.
You need to attach your policy to the port level policy so that it can be a two level policy.
Three Level Class-default Policy Example:
policy-map leaf
class class-default
queue-limit xxxxx bytes
policy-map logical
class class-default
service-policy leaf
policy-map root
class class-default
service-policy logical
Invalid Queue-Limit Policy Configuration Example:
This case "class-default" is being considered as the port level.
Following QOS policy configuration failed because the configuration check assumes user is trying to apply the queue-limit at the vlan level which is not supported.
policy-map child-1
class class-default
queue-limit 256 packets
policy-map VLAN-OUT
class class-default <<< Class default is being assumed at the port level , Child policy at the second level
shape average 5000000
service-policy child-1
interface GigabitEthernet0/5
switchport trunk allowed vlan none
switchport mode trunk
service instance 2 ethernet
encapsulation dot1q 60
rewrite ingress tag pop 1 symmetric
bridge-domain 60
3600-HL-2-N(config)#interface GigabitEthernet0/5
3600-HL-2-N(config-if-srv)#service-policy output VLAN-OUT
QOS: queue-limit command not supported in non-leaf classes
QoS: Policy attachment failed for policymap VLAN-OUT
*Feb 13 09:55:28.700: %QOSMGR-3-QLIMIT_LEVEL_ERROR: Qlimit command not supported in non-leaf classes

I have a problem with wifi in my iphone 4s, i already try everything and download latest version 7.1(11D167) but wifi switch is not working, its my humble request to Apple support team that pls resolve this problem as soon as possible because

I have a problem with wifi in my iphone 4s, i already try everything and download latest version 7.1(11D167) but wifi switch is not working, its my humble request to Apple support team that pls resolve this problem as soon as possible because its a prestiage of Apple Company.
Pls inform me how can i resolve the problem of wifi.

You have to go to autherized iPhone agent.

Could not complete the video frames to layers command because photoshop does not support video in th

When I attempt to import a video I get the message "could not complete the video frames to layers command because photoshop does not support video in this version of windows" I am running on windows 8.1 pro (32 bit), shouldn't this be compatible???????????

Unfortunatly, the 32 bit versions of windows doesn't support video in photoshop cc.
see this post:
http://forums.adobe.com/message/5802978#5802978

Trying to connect HP officejet all-in-one! assitant does not support router??

I am trying to connect HPOfficejet 7410 All-in-One which is wirless enabled to my wireless netowork. Getting message," HP NETWORK ASSISTANT does not currently support the router that is connected to your system." Does this mean that I cannot setup this printer with the router I have? Or is there another way I can connect it without using the Network assistant? The router I have is a Linksys Router Model # WRT110 . I have tried to find another router that was in the list of "supported routers" with no luck. I have looked everywhere. Please if someone could help! Let me know if you need more info to answer my question. Thanks!

Actually, its not that the youre router is not ocompatible with the HP Network Assistant. Maybe yuore router has a very secure network security thats why the wireless assistant could not connect the printer to youre router
- The other way to connect the printer to your wireless network is to run the wireless setup wizard on the printer.
- Step 1. Press the set up button on the printer and press the right arrow then navigate & look for netwok menu then press ok.
- Step 2. press the right arrow and look for wireless setup wizard
- it will look for youre wireless router and try to select your router the enter the security key(WEP or WPA) if you have one.
- after that it will prompt you that the printer is connected to your network
REGARDs --- 1234 --

I have Windows 7, and I am being told that it does not support the newest Ai Illustrator, Are there any other alternate routes I can take to get adobe illustrator and photoshop on my computer? Perhaps an earlier version? Thanks! ~

I have Windows 7, and I am being told that it does not support the newest Ai Illustrator, Are there any other alternate routes I can take to get adobe illustrator and photoshop on my computer? Perhaps an earlier version? Thanks! ~

houseofrest,
According to this page, you can use it for CC:
Adobe Illustrator CC for Mac, Windows, PC - Tech specs
Or you can buy CS6:
http://helpx.adobe.com/x-productkb/policy-pricing/system-requirements-illustrator.html

Switch 3750x not support ip routing command

Similar Messages

Maybe you are looking for