Switch between log and linear in waveform graph

I have a waveform graph that plots linearly. however it creates an error when plotting a logarithmic line. Is there anyway to create a switch that allows me to change the plot between log and linear without creating extra graph?
Thanks
Chris
Solved!
Go to Solution.

Use a property node: Y Scale.Mapping Mode. Writing 1 to the node switches to logrithmic mode and 0 is for linear.
Lynn

Similar Messages

7344 servo motion switching between open and closed loop operation

I have a custom end-of-line test system presently using a 4-axis 7344 servo controller to perform various functional tests on small, brushed DC motors. The system is programmed in C/C++ and uses flex motion functions to control the motor during testing. Motors are coupled to external encoder feedback and third party PWM drives running in closed-loop torque mode from an analog command signal. The system uses all four motion axis channels on the 7344 board to independently and asynchronously test up to four production motors at a time.
In closed-loop mode, the system runs without issue, satisfying the battery of testing protocols executed by this system. I now have a request to add additional test functionality to the system. This testing must be run in open loop mode. Specifically, I need to use my +/- 10v analog output command to my torque drive to send different DAC output levels to the connected motor.drive while monitoring response.
I do not believe the flex motion library or 7344 controller includes functions to easily switch between open and closed loop mode without sending a new drive configuration. I am also under the impression that I cannot reconfigure one (or more) servo controller axis channels without disabling the entire drive. As my system runs each axis channel in an asynchronous manner, any requirement to shutdown all drives each time I change modes is an unworkable solution.
I am open to all ideas that will allow asynchronous operation of my 4 motor testing stations. If the only solution is to add a second 7344 controller and mechanical relays to switch the drive and motor wiring between two separately configured servo channels, so be it. I just want to explore any available avenue before I place a price tag on this new system requirement.
Bob

Jochen,
Thank you for the quick response. The 7344 board does an excellent job running my manufacturing motor assemblies through a custom end-of-line tester in closed loop mode. A portion of the performance history and test result couples the motor through a mechanical load and external shaft. The shaft is in contact with a linear encoder that closes my servo loop.
My new manufacturing requirement is to also sample/document how the small DC motor behaves in open loop operation. Your solution is exactly what I need to perform the additional functional tests on the product I am manufacturing. I see no reason why this cannot work. I was originally concerned that I would need to reinitialize the 7344 board after changing axis configuration. Initialization is a global event and impacts all four channels on the 7344 board.
Using flex_config_axis() to change axis configuration on a single channel without disturbing other potentially running axis channels will solve my concern. It will be several weeks before I can return to the manufacturing facility where the 7344-based testing machine is located. I will update this thread once I verify a successful result.
Bob

How to switch trends on and off in a graph

Hi,
Quite new to this so bear with me. I've numerous temperature sensors I'd like to be able to display on a graphical display. To display all of them on one graph would be a bit of a headache for the user and I don't want numerous graphical displays. I'm after the best way to code this up so I can select the required channels by using individual boolean switches for each channel.
I'm thinking that a switch next to each channel name would be a neat solution to switch channels on and off on the graph.
Thank you
Carl
Solved!
Go to Solution.

LabVIEW 2013 has inbuilt Plot Visible selection in Plot Legand in Waveform Graph

Sapmmc - jstart.exe keeps restarting, switching between green and yellow

Hi Friends,
I installed the SAP core server ( as part of SAP convergent charging) , but jstart.exe and dispatcher-1 process in sapmmc are noticed keep switching between yellow and green. when the jstart.exe turns green (all process running) , dispatcher-1 turns yellow (waiting to start) and when dispatcher-1 turns green (restart-yes) , jstart.exe turns yellow (some processes running). Only for a small duration , they both remain green (may be during transition).
Trace File is as below: Iam not sure as what is missing here to be installed, as it is complaining about JEE directory in
C:\usr\sap\C06\CCD09\j2ee\cluster\bin, which is not present., which was never installed as part of the installation.
trc file: "dev_jstart.new", trc level: 1, release: "711"
sysno      09
sid        C06
systemid   562 (PC with Windows NT)
relno      7110
patchlevel 0
patchno    92
intno      20020600
make       multithreaded, Unicode, 64 bit, optimized
profile    C:\usr\sap\C06\SYS\profile\C06_CCD09_W2K8-Sap-01
pid        3596
ACTIVE TRACE LEVEL           1
ACTIVE TRACE COMPONENTS      All, egi
Wed Oct 26 04:53:47 2011
trace logging activated, max size = 52428800 bytes, 2 versions
arguments :
arg[ 0] : C:\usr\sap\C06\CCD09\exe\jstart.EXE
arg[ 1] : pf=C:\usr\sap\C06\SYS\profile\C06_CCD09_W2K8-Sap-01
trc file: "C:\usr\sap\C06\CCD09\work\dev_jstart", trc level: 1, release: "711"
ACTIVE TRACE LEVEL           1
ACTIVE TRACE COMPONENTS      All, egi
F
F [Thr 3600] Wed Oct 26 04:53:47 2011
F [Thr 3600] *** ERROR => SfCheckJeeVersion: Cannot find JEE binary directory C:\usr\sap\C06\CCD09\j2ee\cluster\bin. [sfxxmain.cpp 848]
trc file: "C:\usr\sap\C06\CCD09\work\dev_jstart", trc level: 1, release: "711"
ACTIVE TRACE LEVEL           1
ACTIVE TRACE COMPONENTS      All, egi
F [Thr 3600] *** ERROR => SfCheckJeeVersion: Cannot find JEE application directory C:\usr\sap\C06\CCD09\j2ee\cluster\apps. [sfxxmain.cpp 857]
F ********************************************************************************
F Java environment properties (C:\usr\sap\C06\CCD09\work\jstart.jvm)
F    root directory    : C:\usr\sap\C06\CCD09\exe\sapjvm_6
F    vendor            : SAP AG
F    version           : 1.6.0_24
F    cpu               : amd64
F    java vm type      : server
F    java vm version   : 6.1.027 1.6-b07
F    jvm library name : jvm.dll
F    library path      : C:\usr\sap\C06\CCD09\exe\sapjvm_6\jre\bin\server;C:\usr\sap\C06\CCD09\exe\sapjvm_6\jre\bin
F    executable path   : C:\usr\sap\C06\CCD09\exe\sapjvm_6\bin
F ********************************************************************************
F    SAP extensions    : available
F ********************************************************************************
I [Thr 3600] MtxInit: 30002 0 2
dispatcher trace
trc file: "C:\usr\sap\C06\CCD09\work\dev_dispatcher-1", trc level: 1, release: "711"
sysno      09
sid        C06
systemid   562 (PC with Windows NT)
relno      7110
patchlevel 0
patchno    92
intno      20020600
make       multithreaded, Unicode, 64 bit, optimized
profile    C:\usr\sap\C06\SYS\profile\C06_CCD09_W2K8-Sap-01
pid        428
ACTIVE TRACE LEVEL           1
ACTIVE TRACE COMPONENTS      All, egi
Wed Oct 26 06:22:16 2011
trace logging activated, max size = 52428800 bytes, 2 versions
arguments :
arg[ 0] : C:\usr\sap\C06\CCD09\exe\jstart.EXE
arg[ 1] : -appTrc
arg[ 2] : -nodeId=0
arg[ 3] : pf=C:\usr\sap\C06\SYS\profile\C06_CCD09_W2K8-Sap-01
arg[ 4] : -hostvm
arg[ 5] : -nodeName=dispatcher-1
arg[ 6] : -file=C:\usr\sap\C06\CCD09\config\jstart.config
arg[ 7] : -jvmFile=C:\usr\sap\C06\CCD09\work\jstart.jvm
arg[ 8] : -traceFile=C:\usr\sap\C06\CCD09\work\dev_dispatcher-1
arg[ 9] : -javaOutFile=C:\usr\sap\C06\CCD09\work\jvm_dispatcher-1.out
F
F Wed Oct 26 06:22:16 2011
F ********************************************************************************
F Java environment properties
F    root directory    : C:\usr\sap\C06\CCD09\exe\sapjvm_6
F    vendor            : SAP AG
F    version           : 1.6.0_24
F    cpu               : amd64
F    java vm type      : server
F    java vm version   : 6.1.027 1.6-b07
F    jvm library name : jvm.dll
F    library path      : C:\usr\sap\C06\CCD09\exe\sapjvm_6\jre\bin\server;C:\usr\sap\C06\CCD09\exe\sapjvm_6\jre\bin
F    executable path   : C:\usr\sap\C06\CCD09\exe\sapjvm_6\bin
F    SAP extensions    : available
F ********************************************************************************
I [Thr 3828] MtxInit: 10000 0 2
M [Thr 3828] NiInit3: NI already initialized; param 'maxHandles' ignored (init=2;par=202;cur=2048)
M [Thr 3828] CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
M [Thr 3828] CCMS: Initalized shared memory of size 60000000 for monitoring segment.
M [Thr 3828] CCMS: Checking Downtime Configuration of Monitoring Segment.
M
M [Thr 3828] Wed Oct 26 06:22:17 2011
M [Thr 3828] CCMS: AlMsUpload called by wp 1004.
M [Thr 3828] CCMS: AlMsUpload failed for C:\usr\sap\C06\CCD09\log\ALMTTREE.DAT.
M [Thr 3828] CCMS: CCMS Monitoring Initialization finished, rc=0.
F
Please help.
Thanks.
Edited by: Zain Ahmed on Oct 26, 2011 9:07 PM

HI,
Import the SAP profiles in SAP transaction RZ10: Utilities - Import profiles - of Active Server
OR
Check what messages do you have in jvm_server0.out, dev_server0.out and bootstrap traces,
also have a look at the note 142100.
The first problem is that in the SCS instance there are no running enqueue server as its starting line have no line break at the end in the start profile. Without this NT cannot parse the line. After adding the line break the enqueue server could start.
The second problem is that in the global dispatcher configuration for the LockingManager the en.port was set to 3201 instead of 3200 (which is correct as the SCS instance has the intance number 00).
After correcting these problems the J2EE engine could be started fine.
see similar threads
Dispatcher - Running but Dialog Queue info unavailable
/thread/96588 [original link is broken]
logon710
Message server not starting
Thanks
Swarup

When frequently switching between mobile and desktop view

When I frequently switching between mobile and desktop view I have to open the layers every time since they get closed/collapsed. Adobe may need to fix it for the next version.

You can use CTRL+# to switch between Code and Design View.
By the way, this is the Dreamweaver Application Development forum which deals with questions about using server-side scripting languages like PHP or ColdFusion. General Dreamweaver questions should be posted in the regular Dreamweaver General Discussions forum.
And while I´m at it: please use descriptive headlines such as "how to switch between Code and Design View" for your posts -- mentioning your screen name "Goula129" is not helpful to other users.

How to quickly switch between straight and curly quotes?

I've recently moved from a Windows XP machine with MS Office to a Mac Pro with Pages.
For the kinds of documents I typically work on, sometimes I need to have straight quotes, and sometimes curly quotes. With MS Word, I was able to create a couple of macros that would switch these preferences for me. With these macros linked to an icon in the toolbar, switching between straight and curly quotes was as easy as clicking a button.
Now I'm looking for a way to do this -- or something like it -- with Pages.
I know how to switch back and forth using the preferences menu, of course, but I'm looking for something quicker and simpler, since I often have to make this change several times a day.
Can Automator do something like this? Or is there another way?
-- Eric

Turn off the auto correction and you can type Curly quotes with:
left single ‘ option ]
right single ’ option shift ]
left double “ option [
right double ” option shift [
If you want the French quotes « and » they are option and option shift |
Peter

Can't switch between fill and outline.

Here's the problem: I'm on an iMac, new, trying to use illustrator CS5. after using CS3 for a few years. In CS5, if I draw a shape, flat, in the illustration, then try to give it an outline, or change the outline, or do anything with the outline, I can't. If I click on the Shape tools in the toolbox and draw out an oval, for example, I can switch between outline and fill without any problems. Select shape, go to toolbox, select curved arrow for switching from one to the other. That's it. But if I draw a freehand shape, then try it, i can't do it. THIS IS A BIG CHANGE FROM PREVIOUS VERSIONS OF THE APP. GET IT? What is the problem? If it's something I have done, fine, tell me and I'll fix it. I tried calling Adobe support in Bangalore, and it took 30 minutes just to get the problem thoroughly appreciated by the techies. They just couldn't get the idea for half an hour! I had to go over it 4 or 5 times. And they couldn't come up with an answer. they were no help at all. I'm hoping the forum will yield better results. This is pathetic, guys. Your 90-day tech support is a worthless piece of crap, guys. The only tech support we have is this catch-as-catch-can forum. I've been using Illustrator since 1987, (illustrator 88) believe it or not, it's true. And I've always been able to get tech support to cure the ills. Not any more. Is that the way Adobe plans to offer tech support? if there were a way to contact Adobe Tech Support by going around Adobe Bangalore, i would use it. But, alas, I am stuck with this.

Dear Monika and Mylenium: I figured out part of the problem, but not the solution: The shape I had drawn -and coudn't switch between fil and stroke on-is one I had already done a gradient mesh on, too. I had later abandoned the gradient mesh by using the option key to delete mesh lines, but that didn't take the shape all the way back to its original flat state. So it wasn't a plain drawn shape any more. So how do I release the gradient mesh to get back to a flat shape? I'm also having trouble keeping the shapes in RGB or CMYK mode-they keep defaulting back to greyscale. Could that also be a symptom of using gradient mesh? Note: I'm using gradient mesh for the very first time now; I've never used it before. It seems to leave a lot of unexpected baggage behind. I would send a screen shot, but if I start up Grab or Voila, all the AI pallets go away, and that's half the information. So how do I control gradient mesh?

Is it possible to install Lion on the second hard disk on my Mini (2010) Snow Leopard Server, and switch between Lion and Snow Leopard? I like those voices Lion has in speech.

Is it possible to install Lion on the second hard disk on my Mini (2010) Snow Leopard Server, and switch between Lion and Snow Leopard? I like those voices Lion has in speech.

When baltwosaid NO emphatically, that was described as CORRECT ANSWER. Ditto in the caeses of the radically different answers from Camelotand Matt Clifton
Could it be that CORRECT ANSWER needs better defining by Apple?
That apart, yes, switching might involve rebooting. About the voices, well, I was the other day adding voice to a commentary in a video I was working on. There's only American English accent in SL — Lion I believe has British ones as well.
Why not, I wondered, try to install Lion purely for academic interest, maybe with an SD card (Sandisk Ultra II, 16GB) as Tom Nelson says is possible at http://macs.about.com/od/macoperatingsystems/ss/Perform-A-Clean-Install-Of-Os-X- Lion-On-Your-Mac.htm

JSF / Switch between HTTP and HTTPS

Hello!
I want to switch between HTTP and HTTPS using JSF.
Under Apache Struts framework I can use struts extension "sslext.jar" to configure switching between http and https in one web application.
e.g. Login-jsp should be secured, all other jsp's should run unsecured.
Any ideas?
regards
Harald.

Thanks,
I made the necessary enhancement for the second phase, password confirmation required when return to SSL zone after leaving it after a succesful login.
I did the following:
1) create a class in the application scope and/or singleton class with the servlet paths that require SSL
2) create a plugin that reads ActionConfigs from the ModuleConfig
3) create a filter that sets a request scope flag that says that password must re-entered.
Code Extracts:
1) MainshopContainer application level parameter singleton class:
private static HashMap sslZoneMap = new HashMap(50); // key = servlet path of request, example /login.do
public boolean isInSSLZone(String servletPath)
return this.sslZoneMap.containsKey(servletPath);
public void addToSSLZone(String servletPath)
this.sslZoneMap.put(servletPath,null);
public int getNumberOfActionsInSSLZone()
return this.sslZoneMap.size();
2) Struts plugin
add a call to loadSSLZoneMap in plugin init method:
loadSSLZoneMap(config, mainshopContainer);
private void loadSSLZoneMap(ModuleConfig config, MainshopContainer mainshopContainer)
throws ServletException
try {
ActionConfig[] actionConfigs = config.findActionConfigs();
for (int i = 0; i < actionConfigs.length; i++)
if (actionConfigs.getParameter().indexOf("/jsp/account/") < 0) // /account/* = URL path for SSL zone
// not found = not ssl zone
System.out.println("loadSSLZoneMap, following actionConfigs excluded from SSL Zone: "+actionConfigs[i].getPath());
else
// found = ssl zone
String servletPath = actionConfigs[i].getPath()+".do";
mainshopContainer.addToSSLZone(servletPath);
System.out.println("loadSSLZoneMap, following servletPath added to SSL Zone: "+servletPath);
System.out.println("loadSSLZoneMap, number of actions in SSL Zone: "+mainshopContainer.getNumberOfActionsInSSLZone());
catch (Exception ex)
ex.printStackTrace();
throw new ServletException("Exception caught in loadSSLZoneMap: "+ex.toString()+" Initialization aborted.",ex);
3)
public void doFilter(ServletRequest request, ServletResponse response, FilterChain chain)
throws IOException, ServletException {
HttpServletRequest req = (HttpServletRequest) request;
HttpServletResponse res = (HttpServletResponse) response;
String servletPath = req.getServletPath();
boolean secure= this.mainshopContainer.isInSSLZone(servletPath);
The wole picture:
The filter adds a RequestDTO object that includes all request parameters, one of them is the secure flag.
I have a session scope class UserContainer that includes all the session parameters, one of them is the lastRequestDTO.(last made request)
At the end of all my jsp's I set the lastRequestDTO variable.
In that method I set the passwordConfirmationRequired flag if needed:
public void setLastRequestDTO(RequestDTO _lastRequestDTO)
if (this.lastRequestDTO != null && this.lastRequestDTO.isSecure() != _lastRequestDTO.isSecure())
this.setPasswordConfirmationRequired(true);
this.lastRequestDTO = _lastRequestDTO;
I read the passwordConfirmationRequired in all my jsp's in the SSL zone that allow editing or deleting and if that flag is true, a valid password must be re-entered in order to make the updates.
When the password is OK I reset the passwordConfirmationRequired to false.
I need some help for the first phase, that is SSL setup for all actions related to jsp's with url path /account/*
I tought I could define it in the web.xml:
<security-constraint>
<web-resource-collection>
<web-resource-name>All Account Related Pages</web-resource-name>
<url-pattern>/account/*</url-pattern>
</web-resource-collection>
<user-data-constraint>
<transport-guarantee>CONFIDENTIAL</transport-guarantee>
</user-data-constraint>
</security-constraint>
but that doesn't work and finnaly understood why:
Example: /WEB-INF/jsp/account/login.jsp corresponds to /login.do
The url pattern /account/* at the container level is never encountered.
Is it allowed to declare the following action path: /account/login instead of /login?
If yes I could add following prefix /account to all my action paths and forward paths and this could resolve my problem.
What's your opinion?
If no, would your library resolve this?
Will all the Struts/JSP/JSTL url generating tags pick-up the required protocol (http/https) according to your configuration file?
Regards
Fred

Is there an easy way to switch between ehternet and wifi connection without having to disconnect the ethernet cable?

Hi All
Was wondering if there is an easy way to switch between ethernet and wifi connection on Apple TV without having to disconnect the ethernet cable. The reason I ask is that I find it quicker to use my ethernet connection via a Netgear Powerline Home Theatre Set-up to stream Trailers and Movies on the Apple TV, however this is no good when connecting directly to my Mac to stream music or TV shows in iTunes, so revert to the wifi connection that I created on my Time Capsule to do this.
Would be handy if Apple TV had a menu option where you could manually change the connection type depending on what you were doing, as per above scenario.
Cheers
Brett

brettfromseabrook wrote:
Hi All
Was wondering if there is an easy way to switch between ethernet and wifi connection on Apple TV without having to disconnect the ethernet cable.
Unfortunately not.

Switching between Design and JSP tabs add code?

I am new to SJSC and I am taking the time to go through all of the little odds & ends of the IDE.
I was looking at:
http://blogs.sun.com/roller/page/tor?entry=computing_html_on_the_fly
And I decided to try this.
When I add the following in the JSP tab:
<h:outputText binding="#{Page1.tableHtml}" id="outputText1"/>Save.
Then click on the Design tab, then go back to the JSP tab, I now have:
<h:outputText binding="#{Page1.tableHtml}" id="outputText1"/>
<h:outputText binding="#{Page1.outputText1}" id="outputText1"/>It's late here, but this doesn't make any sense, why would switching between Design and JSP tabs add code?
Thanks,
--Todd

Girish: I followed these steps:
1.) Downloaded:
Sun Java Studio Creator 2, Multilanguage creator-2-windows-ml.exe 254.23 MB
2.) When I started the install, I received the message:
Welcome to Sun Java(TM) Studio Creator 2! You are installing: Sun Java Studio Creator 2 development environment Sun Java System Application Server Platform Edition 8.1 2005Q1 Update Release 2 Bundled database
3.) Installed version:
Product Version: Java Studio Creator 2 (Build 060120)
IDE Versioning: IDE/1 spec=5.9.1.1 impl=060120
Also, Under, the Palette window: Standard component list, there is a component labeled Output Text.
When placed on a jsp, the following code is produced:
<h:outputText binding="#{Page1.outputText1}" id="outputText1" style="position: absolute; left: 24px; top: 48px"/>Thanks,
--Todd

Unable to switch between 3g and 4g on my Lucid

After an update a week or so ago, my LG Lucid has completely lost the functionality of switching between 3g and 4g. As 4g is a battery hog I kept it mostly on 3g (but not always) and since the update , I am stuck on 3g. Took it to the Verizon store for a techie to look at it and he was stumped. I used to access thru "settings" - "about phone" - "network" - "network type and strength" , which brought me to some toggles where I could choose the network best suited to what I was doing. Now this screen is gone completely and only shows signal strength. The techie suggested a factory data reset, which would not only erase all my items from my phone, but if it did provide 4g service, I would now be stuck all the time on that. I told the tech guy I would wait for a fix to this. My question is, are there others out there with this problem or is there a fix for it. I contacted LG and they said they have had no updates to the phone. Is Verizon denying the problem or even working on it ?????

I have a related issue with my LG Lucid. It tends to get stuck in 3g in areas that I know are 4g. A phone restart usually takes care of it but it sure is a pain to do that. If that fails then a battery remove/replace fixes it. Neither are good options but worth considering while we wait for an update.
There are several 3g/4g switch free apps available too but none that say they support Lucid. I found that 3G/4G On/Off (Toggle 3G) by JuYeo! Oh works well to turn on 3g when the Lucid doesn't do it but I haven't found a way to turn on 4g.

Do I need to reset the router when switching between Win and Mac?

I just set up my new Mac Pro with OSX 1.5.2 and Win XP using Bootcamp and it all works fine, but I have one question about connecting to the internet.
I have a Belkin pre-N wireless router. I am connected using an ethernet cable.
When I switch between OSX and Windows by restarting the computer, is it necessary to restart the router while the computer is off so that when it comes back on it can locate its proper connection?
When I was working on my old PC and my new Mac Pro, I noticed that if I just took the ethernet cable from the Mac or PC and connected it to the other machine, it couldn't find the internet unless I turned off the router, waited a moment and turned it back on again, connected to the other machine and then started the machine.
As the two OSs are now in the same machine, will this continue to happen or can I simply switch between operating systems without having to re-initialize the router and connect it before turning on the computer again?
I haven't tried it yet because I am afraid to screw things up, so I am continuing to turn off, restart the router, re-connect and turn the computer on again. That work perfectly but it is tedious.
Can anyone please advise on whether this is necessary or not?
Thanks a lot for any advice.

Luis:
You should be able to leave the router on and switch between the two OSes. Try it. Worst thing that can happen is that you would need to restart the router.
Axel F.

Docked T500 - Switch between headphones and speakers

Hey guys,
I am using my T500 with an Advanced Mini Dock at work. I keep the headphones (with microphone) plugged into the docking station.
Sometimes I want to listen to the audio on my laptop's speakers rather than inside the headphones. Is there any way I can make this switch without unplugging the jack from the docking station.
I know that above the volume bar for some systems you are able to switch between headphones and speakers and also, up until ~1 month ago I was able to do this from the SmartAudio utility, but now I can't. I can just switch between SPDIF and headphones.
I am using Windows 7 64-bit and I have all the latest drivers and apps that come using the "System Update" utility.
Please let me know if you have a solution for this.
Thank you,
Ciprian

I'm pretty sure that the blame for this lies entirely with Microsoft and their stupid hardware-detecting W7 OS. Yes, it actually detects when you unplug the headphones, tells you what you just did, and promptly resets all sorts of things. The most sensible thing you can do (apart from reverting to XP, which doesn't do this) is to plug an external stereo jack to stereo jack socket extension lead, and plug either your headphones or speakers into that instead, whilst leaving the plug end permanently in the laptop. Microsoft can't pull that stupid stunt on an external connector, so you should be okay with that.

Dynamic switching between stacked and non-stacked detail groups?

Hi guys,
Is it possible to dynamically switch off/on stacking of detail groups?
I would like to give the user the option to switch between stacked and non stacked
Regards
Bar
JDev: 10.1.3.2
JHS: 10.1.2.26

Yes and No. No because it is not supported out-of-the-box by JHeadstart, yes because you can do this post-generation and then move the custom code to JHeadstart templates.
However, it is not a trivial thing to build, you can try the JDeveloepr forum for any help, we can help you with moving the post-generation code to custom templates, since that is the JHeadstart-related part of your question.
Steven Davelaar,
JHeadstart Team.

Switch between log and linear in waveform graph

Similar Messages

Maybe you are looking for