Switch port configuration for 3500i AP

Hi,
We are due to install a brand new enterprise WLAN based on the WiSM2 platform, 3502i AP and WCS. The APs will be plugged into the 2960S-24TPS-L.
I have scanned over all documentation and cannot for the life of me find a recommended switch port configuration for connecting the AP to the switch in terms of speed / duplex etc. For example, should I just configure the port to auto detect, or is forcing the speed / duplex the way to go. I could also do with knowing other best practice configurations for AP connectivity.
Any help would be greatly appreciated.
Chris.

The AP comes online with just auto detect, but I want to know if there are any benefits to forcing this to 1Gbps / Full duplex, or even if this is the right way to go. I suspect auto detect is the best method.

Similar Messages

  • AP-1131AG: 2 VLANs/SSIDs, switch port configuration?

    We're setting up a (seemingly) simple deployment of some APs, and want 2 SSIDs...one will have Pre-Shared WEP and one will be open and broadcast (with access-lists on the router). My question is how to set up the switch port to match my AP, in order for it to pass both VLANs (in this case I've setup WLAN100=VLAN100 and WLAN101=VLAN101)...Do I have to configure trunking on that switchport? Thanks for any links or answers on this!!!

    Hi Vince,
    Here is a great doc that goes over this concept in detail. You will need to configure Trunking on the switchport. Have a look at what yours might look like;
    switchport mode trunk
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 1
    switchport trunk allowed vlan 1,100,101
    From this excellent doc;
    Using VLANs with Cisco Aironet Wireless Equipment
    http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml#clic2935xl
    Hope this helps!
    Rob

  • How to get Networking Switch Port Configuration (I guess SNMP4j will help)

    Greetings :)
    We have extreme Summit 450e switches installed in our organization. approximately 2000 desktops are connected to these switches.
    Now, I want to make a utility to get info from these switches, for example, which IP, MAC etc is running on a particular switch port. I want to extract these kind of info from all switches and export it into a database.
    Any help, how to start this work.
    Thanks...

    > Any help, how to start this work.
    First research what programmable interfaces it supports.  That includes any management API including SNMP, TCP and HTTP.
    And then from that figure out what you want to do with it.
    After you do both of the above then you start looking to java to program the solution.

  • Tandberg C20 switch port configuration

    Is there a recommended switch port setting (3750x) for connecting a Tandberg C-Series (20,40,60)?
    Smartports?
    Port-Security?
    Access-port only?

    The AP comes online with just auto detect, but I want to know if there are any benefits to forcing this to 1Gbps / Full duplex, or even if this is the right way to go. I suspect auto detect is the best method.

  • ESX/VMWare Switch Port Configuration

    Does anyone know how to configure a 3560 switch port that is connecting to an ESX host with multiple VM's??

    Hi Jason,
    Most of the time people will configure the port as a trunk to the ESX host.  So on the 3560 you can just do:
    switchport trunk encap dot1q
    switchport mode trunk
    This will allow your VMs to be in different vlans if you would like.
    Chad Peterson
    CCIE 23213
    Network Consulting Engineer
    .:|:.:|:.
      CISCO
    PDI Data Center
    http://www.cisco.com/go/pdihelpdesk

  • Dynamic port configured for FILE adapter is not working

    Hi,
    I have a simple dynamic port in an orchestration that writes a file to a file location. Here is the configuration
    ================
    FilePort(Microsoft.XLANGs.BaseTypes.Address) = "FILE://c:\\TestFolder\\Out";
    FilePort(Microsoft.XLANGs.BaseTypes.TransportType) = "FILE";
    ================
    When I run this orchestration, the dynamic port does not write the file to the folder, however I does not show any error either. It is always in "Ready to Run" state where the message is "Queued Awaiting".
    I tried all sorts of combinations like FILE:// FILE:\\ File: file:// file:\\ etc... and also without the moniker, just c:\.... I get the same problem.
    when I use a static port(subscribed to the same message) it works fine. When I use a static port ALONGWITH this dynamic port then both works fine !!! I receive 2 files.
    but when I use only dynamic port it does not work!!
    Anybody knows how to solve it.
    THANKS IN AVANCE
    PLEASE HELP
    Surya

    It could be becasue you 're not passing in the file name, Try something like this..
    SndPort_Dynamic(Microsoft.XLANGs.BaseTypes.Address)=@"file://C:\Test\Try\Out\Test1.xml";
    But even when you don't pass the file name, i was expecting the erro to be like:
    The FILE send adapter cannot open file C:\TestFolder\Out\ for writing.
    Details: The system cannot find the path specified.
    But try with File Name and restart the host instance after the change.
    Or use somehting like this:
    FilePort(Microsoft.XLANGs.BaseTypes.Address)=@"file://C:\Test\Try\Out\\%MessageID%.xml";
    FilePort(Microsoft.XLANGs.BaseTypes.TransportType) = "File";
    If this answers your question please mark it accordingly. If this post is helpful, please vote as helpful.

  • AEBS Port configuration for Bittorrent in Windows XP

    So I've been using my AirPort Extreme Base station for a while now, and am really enjoying it. I have a Windows XP PC hooked up to it via a LAN and am using a MacBook Pro to connect to the internet wirelessly through the AEBS. I'd like to start using Bittorrent on my PC but, since it goes through the AEBS there are firewall issues and I need some information as to how to configure the ports on the AEBS to allow Bt through my firewall. Anyone have any suggestions? Thanks,
    Scott
    Desktop PC   Windows XP  

    Scott,
    You need to set up something called Port Forwarding, Port Mapping, as it's called in the AirPort Admin Utility.
    Fire up the AAU (in Applications/Utilities) on the MacBook Pro, select the AEBS, click Configure and click the Port Mapping tab. Then you need to Add a configuration, specifying the public port (BT default is 6881, but you can specify something different in your BT client), an IP address to forward it to (the IP address of your XP box), and a private port, using the same as for the public port is a good idea as your BT client will publish this and listen on this port.

  • Advice about FXS Port configuration for connecting to modems

    Hello all,
    We have not confirm the problem, but we are having reports that analog devices like USR V.92 Modems and Power meters are not connecting or dropping the connection.  We have an ISR 2911 with the 4-port FXS-DID WIC (VIC3-4FXS/DID), configure to an internet SIP truck provider.  The Router is running IOS 15.3(3)M2.  If we connect an analog phone to the FXS port and call, voice is clear.  So the question is what configuration settings should we have for FXS ports and/or dialpeers for connections to modems?  Attached is the current configuration of the router.  
    Do we have to be worried about Codec?  If so which Codec should we configure?
    Any Physical FXS settings should be set?
    Are my DSP setup correctly?  
    Again, I'm at a loss, as voice sounds good and my searches for modem connections to FXS Ports on CUCME is coming up dry.  Any help would be great.  
    As far as the "Power Meters", we are talking substation power meters.  
    Thanks for any advice you can spare and your time,
    Nick

    Hi Amit,
    No problem on the delay.  Your help is very much appreciated.  
    You're losing me a bit.  Because I don't know if your giving me dial-peer 1 as an example.  1 being just a random number.  Or your telling me to change my current dial-peer 1 configuration.  Which is currently a pots dial-peer:
    dial-peer voice 1 pots
    description POTS port 0/1/0
    destination-pattern 111111111
    port 0/1/0
    dial-peer 1000 voip is our outbound call leg.  Sorry call legs are not exactly clear to me yet.  In fact they haven't been in years.  :)  So change my dial-peer to dial-peer voice 1 voip?  
    My other question still unknown to me is should we use:
    fax protocol pass-through g711ulaw
    Even though we are trying to use a modem and not a fax?  Also this command is a dial-peer command and not a global command.  So what global command should i be using?
    Again thank you for your time and help,
    Nick

  • Port configuration for OAS 10.1.3.4

    Hi Gurus,
       We have installed the Oracle Application Server 10.1.3.4 and deployed custom applications.  The Application server is listening on default port 7777 and we want to configure the port as 80 instead of 7777.  Can you please let me know the steps how to configure the port 80 with OAS 10.1.3.4?  The application server is installed on OEL 5.4 32 bit.
    Thanks
    Samar

    Why dont you try CentOs, this is a free Linux based on RedHat, is the same thing only that is free you can get it in the page of CentOs, I've used before and it works nicely well, and you dont have problems with updates or packages.
    Greetings.

  • Port configuration for servlet

    I am new to servlet. i am using tomcat 4.0 as a server. i need to run servlet on the server. do i need to have servlet server (JSDK 2.X) for that? n i came to know that servlet also works on port 8080 same as tomcat. can i change the port of a servlet? if yes then how?

    hi,
    if u r using tomcat as standalone for ur development u can change the port number. this variable can be changed in installed_dir/conf/server.xml.
    the element looks like this
    <Connector
    className="org.apache.c............"
    port="8080"
    ..../>
    change the port="whatevernumberuwant"
    but see that there is no process on that port before changing.

  • CATALYST 2820, console port config for modem

    Hi,
    I’m a 2nd semester CCNA student, and I purchased a old CATALYST 2820 switch for training purposes. I do not know the password and the console port has been configured for a modem. I thought that it would be easy to reset the password—but cannot find any way to do it with the 2820, and the console port configured for a modem.
    Does anyone know what the default factory password is? If the password has been changed (from the factory default), how can I reset the system?
    Thanks!

    I appreciate your help!
    I did look at that link several times—my 2820 has a mfg. date of Sept 97. I held in the Mode button, but the LED above port 1x does not come on (held it in for over a minute). I never see any info. using the console port.
    I did try attaching a modem to the console port—it works—I get a login prompt. I don’t know if it is the factory default password. I know that the rollover cable is working—tried a 827-4v.
    Am I doing something wrong???
    Thanks, David

  • Port Configuration EDI/IDoc

    Please anybody can explain me in detail Port Configuration for EDI/IDoc(T Code WE21).
    please explain how can i create new port.
    it's urgent please.
    thanks
    RP

    rp
    check the following links
    http://help.sap.com/saphelp_47x200/helpdata/en/af/7e844367c24d4a950df3205052769d/frameset.htm
    http://help.sap.com/saphelp_erp2004/helpdata/en/dc/6b835943d711d1893e0000e8323c4f/content.htm
    http://www.sapgenie.com/sapgenie/docs/ale_scenario_development_procedure.doc
    http://edocs.bea.com/elink/adapter/r3/userhtm/ale.htm#1008419
    http://www.netweaverguru.com/EDI/HTML/IDocBook.htm
    http://www.sapgenie.com/sapedi/index.htm

  • How to recover from network port configuration deletion (airport)

    a couple of years ago, i accidently deleted the network port configuration for AirPort in the Show pop-up menu. No big deal, i thought at the time. I don't have an AirPort card and I won't be using AirPort in this computer. Ok, I now have an old-style AirPort card (powerbook G3 firewire, 10.2.8) and the AirPort utility doesn't see that it's installed. I realized right away, the network doesn't have a port... so the system doesn't see it, right? So, how do I get this port back? Do I have to reload a new System entirely and not save previous network settings... or is there an easier way to recover from my blunder?

    Thanks Rob,
    Glad to be here. Yeah, 10.2 works the same as 10.4. The problem with what you suggest is that I can no longer get airport as an option in Network port configs... so when I go to the new button all the other options are there EXCEPT AirPort. This is what I need to restore. I haven't checked, but I'm assuming I've nuked the pref panel out of the master library. So, I've messed up big time. I was looking for a way to recover that didn't involve reloading the whole system. This isn't like OS 9 and older where you can go and pick a little piece and stick it back into your system folder... I think. Thanks for the reply.

  • LMS 4.2 - How do I find switch ports that are configured as trunks.

    I've been tasked with finding all switch ports that are configured as Trunks. We plan to use LMS 4.2 to push (via Netconfig) new interface level commands to all user (non-trunked) ports. From my experience, this poses a problem because we do not know which ports are configured as trunks -vs- user ports.
    Using Netconfig is not going to be easy since there is no way to script this. It would be great if I could run a show command on a switch and then have CWSI peform a change based upon the output.
    In other words, we need a way to run a job based upon the output of a command.
    Is there a section of LMS that I could use for help with this?
    Thanks,

    You need to go to Monitoring>Dashboard. Here Just click the switch in the Llisted device and then click the interface you will find the all the down and Up interface with type of configuration (i.e. Trunk or Access.)

  • What is the recommenden access port QoS configuration for 8900/9900 video enabled phones

    Hi all,
    we are currently starting to roll out some video enabled 9900 and 8900 phones in our network. In the past we did not use video and configured the access ports on our Catalyst 2960 switches with "auto qos voip ciscp-phone". This however creates a policy which does not include a class-map to correctly handle the AF41 video traffic coming from those phones. I have thougth about extending the autoqos policy with a AF41 class-map but am not sure if this is the right way to do it. 
    That's what I have in mind:
    class-map match-all AUTOQOS_VIDEO_DATA_CLASS
      match ip dscp af41
    class-map match-all AUTOQOS_VOIP_DATA_CLASS
      match ip dscp ef
    class-map match-all AUTOQOS_DEFAULT_CLASS
      match access-group name AUTOQOS-ACL-DEFAULT
    class-map match-all AUTOQOS_VOIP_SIGNAL_CLASS
      match ip dscp cs3
    policy-map AUTOQOS-SRND4-CISCOPHONE-POLICY
     class AUTOQOS_VOIP_DATA_CLASS
       set dscp ef
      police 128000 8000 exceed-action policed-dscp-transmit
     class AUTOQOS_VIDEO_DATA_CLASS
       set dscp af41
      police 1500000 8000 exceed-action policed-dscp-transmit
     class AUTOQOS_VOIP_SIGNAL_CLASS
       set dscp cs3
      police 32000 8000 exceed-action policed-dscp-transmit
     class AUTOQOS_DEFAULT_CLASS
       set dscp default
      police 10000000 8000 exceed-action policed-dscp-transmit
    How do you guys do it ? Is there some documentation for this ? 
    Thank you for your kind help
    best regards
    Andreas

    Hi
    You have to keep this table on your mind. Your configuration is fine if your configuration for SD video , but if for HD video , it is not ok you have to change video bandwidth at least 5M.
    Traffic Type
    Layer 2 CoS
    Layer 3 IP Precedence
    Layer 3 DSCP
    Voice RTP1
    5
    5
    EF
    Voice control
    3
    3
    AF31
    Video conference
    4
    4
    AF41
    Streaming video (IP/TV)
    1
    1
    AF13
    Data
    0-2
    0-2
    0-AF23
    *Interactive Video "AF41"- Sensitive but can tolerate packet loss of about 1% and latency almost same as voice.
    *Streaming Video "AF13" - Less sensitive - can tolerate about 4-5% packet loss and latency of about 4-5 seconds.
    *HD video conference will require between 5M to 16M , but SD video conference will use 384K to 1 M
    Note:-Video QOS , if you will assume that your video conference will use around 384K , you have to add 20% because video conference include voice so the total bandwidth 460K.
    Kindly check the below link
    http://www.sdcug.com/wp-content/uploads/2011/04/Campus-QoS-for-Voice-and-Video.pdf
    Thanks
    please rate all useful information

Maybe you are looking for

  • Oracle EPM 11.1.1: Business Rules issue

    Hi All, I have installed Oracle EPM 11.1.1 and I have created a planning application. However when I logon to Analytical Administration console and try to create a business rule I am facing the following issue: 1. When I try to select Planning Applic

  • Web Dynpro ABAP call transaction in the foreground

    In Screen Painter/SAP ALV, we can create a screen where for example if you double click on a sales order field it can take you a VA03 transaction by : call transaction VA03 ... and skip first screen. I am creating Web Dynpro ABAP application that nee

  • Hello i need help in itunes.

    hello, i recently downloaded some cd's and added to my itunes library but albums and songs say unknown. how can i name songs/albums? please help! thank you!

  • How can I access my iPhone backup stored in iCloud?

    Hi, My iPhone was stolen a few months ago and I now have an Android phone. I have an iPad and it shows that my iPhone was backed up onto iCloud. How can I access this back up to retrieve my photos/notes etc? Thanks Jessica

  • Which ipad can read a PDF doc

    Which is the least expensive ipad that can read a PDF drivers manual  & other things to my severely dyslexic child?  Can any of the older refurbished ipads dot that? Thank you for any input!!