Switch support for NAC CCA for 6500 series switch

per the 4.0 document "switch support for Cisco NAC" there is a note that says
Catalyst 6000/6500 on IOS do not support mac-notification
Does this mean you cannot deploy layer 2 OOB mode, as snmp notification to the CAM will not happen with the 6k platform?

Probably, the configuration guide will give you better idea about your problem.
http://www.cisco.com/en/US/products/hw/switches/ps708/products_configuration_guide_book09186a00803f5611.html

Similar Messages

How to remove the WiSM2 from the Catalyst 6500 series switch?

Hello, can you explain to me how to safely remove the WiSM2 from the Catalyst 6500 series switch?
According to the documentation "Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note":
To remove the WiSM2, perform these steps:
Step1     Shut down the module by one of these methods:
In privileged mode from the router prompt, enter the hw-mod module mod shutdown command. NoteIf you enter this command to shut down the module, you must enter the following commands in global configuration mode to restart (power down, and then power up) the module:
Router# no power enable module modRouter# power enable module mod
If the module does not respond to any commands, press the SHUTDOWN button located on the front panel of the module.
Step2     Verify that the WiSM2 shuts down. Do not remove the module from the switch until the POWER LEDis off.
But, in the case of Step1 (1st methods) I do not see a option "shutdown" in the command "hw-mod module 3"...
All I prompted to enter is:
c6500#hw-module module 3 ?
boot           Specify boot options for the module through Power Management Bus control register
reset          Reset specified component
simulate Simulate options for the module
Is it hidden options? IOS version of c6500 is 12.2(33)SXJ1
In the case of Step2 (2nd methods) there is not any button on the front panel of the module?
And yet, it is better to remove the module configuration manually or use the command module clear-config prior to removing the module?

Good catch.
Which one is true, will get back to you on this if i've something soon.
http://www.cisco.com/en/US/docs/wireless/module/wism2/installation/note/WiSM_2.html#wp34727
The above link is procedure to remove wism2. This procedure doesn’t look like wism2 is hot swapable.
http://www.cisco.com/en/US/docs/wireless/module/wism2/installation/note/WiSM_2.html#wp34621
All modules, including the supervisor engine (if you have redundant supervisor engines), support hot swapping. You can add, replace, or remove modules without interrupting the system power or causing other software or interfaces to shut down. For more information about hot-swapping modules, see the Catalyst 6500 Series Switch Module Installation Guide.

APs unable to receive IP address from DHCP (core 6500 series switch)

Dear Friends,
a week ago I had stable wireless network APs were getting IPS from 6500 series switch (DHCP) but unfortunately some WISM got rebooted and now APs are unable to receive IP address from Core 6500 DHCP, to cater this issue I have another DHCP server configured on windows 2008 i created another subnet and and put APs in that vlan now all APs are are successfully receiving IPS from windows DHCP server I don't know why APs are not able to receive IPs from core 6500 series DHCP.
please advice
Thanks
Faysal

Thanks george for stepping up here is DHCP config
ip dhcp excluded-address 10.10.30.1 10.10.30.20
ip dhcp excluded-address 10.10.8.1 10.10.8.10
ip dhcp excluded-address 192.168.10.1 192.168.10.5
ip dhcp excluded-address 10.9.20.1 10.9.20.30
ip dhcp pool vlan_30
network 10.10.30.0 255.255.254.0
default-router 10.10.30.1
option 60 ascii """"""""""""""""""""""""CiscoAPc1250""""""""""""""""""""""""
option 43 hex f110.0a0a.1e0b.0a0a.1e0d.0a0a.1e0f.0a0a.1e11
dns-server 10.10.2.11
lease infinite
ip dhcp pool WiSM1_SP
network 192.168.10.0 255.255.255.248
default-router 192.168.10.1

Multicast in 6500 series switch

We have one customer who have config Ipsec over GRE end to end for all remote locations.Now customer want to upload large file to all remote locations.So we have to config multicast in our backbone network.
We have 6500 Series Switch thorough which all routing is done.But how multicast traffic will flow thorough IPsec tunnel.Is any one having such case pls let me know.
TIA
Regards
SAM

check out the following link Multicast over IPsec VPN Design Guide, this should help :
http://www.cisco.com/application/pdf/en/us/guest/netsol/ns656/c649/cdccont_0900aecd80402f07.pdf

5508 WLC-6500 Series Switch Etherchannel

Hi,
I have a 5508 controller connected to a 6500 VSS pair. Below is the port channel configuration and port configuration. I am just wondering whether we still have to configure a load balancing method as cisco recommends “port-channel load-balance src-dst-ip” as best practice.
Does this still applicable for 5508 controller-6500 Series uplink as the etherchannel is L2 etherchannel?
Port Channel Config:
interface Port-channel1
description To 5508 WLC
switchport
switchport trunk encapsulation dot1q
switchport trunk native vlan 9
switchport trunk allowed vlan 10,11,12
switchport mode trunk
mls qos trust dscp
end
Interface Config:
interface GigabitEthernet1/1/42
description To 5508 WLC
switchport
switchport trunk encapsulation dot1q
switchport trunk native vlan 9
switchport trunk allowed vlan 10,11,12
switchport mode trunk
wrr-queue bandwidth 5 25 70
wrr-queue queue-limit 5 25 40
wrr-queue random-detect min-threshold 1 80 100 100 100 100 100 100 100
wrr-queue random-detect min-threshold 2 80 100 100 100 100 100 100 100
wrr-queue random-detect min-threshold 3 50 60 70 80 90 100 100 100
wrr-queue random-detect max-threshold 1 100 100 100 100 100 100 100 100
wrr-queue random-detect max-threshold 2 100 100 100 100 100 100 100 100
wrr-queue random-detect max-threshold 3 60 70 80 90 100 100 100 100
wrr-queue cos-map 1 1 1
wrr-queue cos-map 2 1 0
wrr-queue cos-map 3 1 4
wrr-queue cos-map 3 2 2
wrr-queue cos-map 3 3 3
wrr-queue cos-map 3 4 6
wrr-queue cos-map 3 5 7
mls qos trust dscp
channel-group 1 mode on
end

Hello,
Please check to following link regarding load balancing between 5508 and WLC 6500:
http://www.learnios.com/viewtopic.php?f=5&t=34555

Cisco Prime LMS 4.1 - Support for Cisco Catalyst 3560-C Series Switches

Hello together
I have a customer which uses the following switch. Last year I have installed LMS 4.1 for him to manage the switches. Unfortunatly the switch model is not supported. According to the information found on the following site the switch is supported for most of the modules in LMS:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/device_support/table/lms41sdt.html
The oid object of the device is the following: 1.3.6.1.4.1.9.1.1465
Supported Software: 12.2(55)EX (Customer has 12.2(55)EX3
Version Support Type: Device Update
So I updated all device updates I was able to find.
Step 1: For that I went to Admin > System > Software Center > Schedule Device Downloads and created a job where I have downloaded the latest versions of all packages.
Step 2: Installed the downloaded packages Admin > System > Software Center > Device Update and installed all the packages.
Unfortunatly I don't see the same result like described in the Supported Device Table for LMS 4.1.
- Cisco View -> works
- Inventory and Config Collection -> works
- Fault Monitor not working -> Error Code Unsupported
- Network Topology Layer 2 Services -> Device Type ciscoProducts.1465, Symbol Question Mark
- VLAN Management -> Doesn't work
- User Tracking > seems also not to work
When I open the report for supported devcies (Reports > System > Device Support) and search for C3560C... I find the following devices, but not mine which i need:
C3560C-8PC-S     .1.3.6.1.4.1.9.1.1466
C3560CG8PC         .1.3.6.1.4.1.9.1.1317
C3560CCG8TC     .1.3.6.1.4.1.9.1.1318
wsC3560CPD8ptS     .1.3.6.1.4.1.9.1.1368
Does anybody have experience with the same switch type / model? Am I doing something wrong or is this type of switch not implemented correctly till now? Further the docuemntation supported devices would be wrong.
Thanks for any feedback Erich

Thanks but I just heard back from my Cisco SE and he assures me that an AP will NOT use up a license.
I've asked him to verify his answer for me.
Is your answer based on real world expereince (the best there is)? That is, are you running Prime LMS 4.1 and does it indeed use up a license for each light-weight AP it discovers & manages?
Thanks for mentioning options 1-3 but I do not wish to employ any of them. I don't mind buying the additional licenses for APs ... I just need to know if I have to or not.
Ian.

Vibration specification of the 6500 serie switch

We are doing heavy contruction work near an important network room and we want to know what kind of vibration the 6509 switch can tolerate. In the specsheet (http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/hardware/Chassis_Installation/Cat6500/6500_ins/01over.html), there are vibration specifications but it is unclear what is the permitted level during operation. I guess the vibration section is what I'm looking for:
Operational—3 Hz to 500 Hz,
Power Spectral Density (PSD)—0.0005 G2/Hz at 10 Hz and 200 Hz. 5 dB/octave roll off at each end. 0.5 hours per axis (1.12 Grms).
I believe that the specified value refers to a test that is done on the unit (using in the specified PSD shape). The test is repeated in each axis for 0.5 hour. What about the 1.12Grms? I though it would be the sqare root of the intregration of the PSD from 3 to 500 Hz, but it doesn't seem to add up.
That being said, would it be right to use the PSD shape a the vibration limit not to go over?
thank you.

We are doing heavy contruction work near an important network room and we want to know what kind of vibration the 6509 switch can tolerate. In the specsheet (http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/hardware/Chassis_Installation/Cat6500/6500_ins/01over.html), there are vibration specifications but it is unclear what is the permitted level during operation. I guess the vibration section is what I'm looking for:
Operational—3 Hz to 500 Hz,
Power Spectral Density (PSD)—0.0005 G2/Hz at 10 Hz and 200 Hz. 5 dB/octave roll off at each end. 0.5 hours per axis (1.12 Grms).
I believe that the specified value refers to a test that is done on the unit (using in the specified PSD shape). The test is repeated in each axis for 0.5 hour. What about the 1.12Grms? I though it would be the sqare root of the intregration of the PSD from 3 to 500 Hz, but it doesn't seem to add up.
That being said, would it be right to use the PSD shape a the vibration limit not to go over?
thank you.

Any one ever worked on 6500 series Cisco switches QOS or 6503 or 6524 QOS(Urgent help needed)

Hi All,
I am having issue specifally doing QOS configuration on 6503 or 6524 or 6509 switches. I am unable to match any EF(voice) traffic for eompls(vlan based) on 6503 cisco switch. If i use any other router as 2811 or 2821 my QOS configuration works perfect but if i put 6503 as PE2 it does not work.i am using vlan based eompls.
Below is the scenario & configuration which i am having issue.
CE1(2821 router)(dot1Q)--------->PE1(2821 router)------->P(6524 switch)-------->PE2(6503 switch)------->(dot1Q)(2821 switch)CE2.
On CE1 i can match ip-precedence 5 traffic and mark that traffic to cos5 on outbound port.On PE1 i can match cos5 packet and mark with mpls exp top5 on inbound port, on outbound port i can match mpls exp 5.
On PE2(6503) i am unable to match that mpls exp5 packet on inbound port. none of the configuration worked on 6500 series switches with mls qos, ,mls qos trust dscp,mls qos trust cos etc. Although i can match cos5 traffic on CE2 on inbound interface.i can not match mpls exp 5 traffic on 6503 and all i can see traffic as default-class on 6503 switch. I tried many things and many configurations on 6503 but nothing worked.If i put 2821 router as PE2 instead of 6503 my qos configuration works. but why if i put 6503 my same qos configuration does not work?
---match means=classification or classify
Can anyone tell me how qos works on 6500 series switches or where i am having issue in my scenario.
i am using this ios on 6503: s72033-advipservicesk9_wan-mz.122-33.SXI3.bin.
below r my questions for 6503 qos:
1.do i need to use some other map tables,am i using correct map tables on 6503 as cos-dscp,dscp-cos,exp-dscp etc.
2.any other configutaion of qos needed on 6503?
3.i am unable to match anything on outbound port of 6503.
4.on 6503 i am using sup720 and PFC3BXL.any specific configuration needed for PFC3bxl.
5. 6503 not allowing me to match qos-group on inbound interface, not allowing me to set cos5 on outbound interface. not allowing me to set cos5 as an inbound interface.
CE1(2821) config:
class-map match-any EF
match ip precedence 5
class-map match-any data
match ip precedence 3
policy-map ip2mpls
class EF
set cos 5
class data
set cos 3
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.455
encapsulation dot1Q 455
ip address 172.16.15.1 255.255.255.252
service-policy output EF
PE1(2821) config:
mls qos map cos-dscp 0 8 16 24 32 40 48 56
class-map match-all exp_3
match mpls experimental topmost 3
class-map match-all mpls_exp
match mpls experimental topmost 5
class-map match-any cos3
match cos 3
class-map match-any LOO1
match cos 5
policy-map EF
class LOO1
set mpls experimental imposition 5
class cos3
set mpls experimental imposition 3
policy-map QOS_G_5
class mpls_exp
priority
class exp_3
bandwidth 500
interface Loopback0
ip address 3.3.3.3 255.255.255.255
interface FastEthernet0/0
ip address 192.168.23.2 255.255.255.0
ip ospf network point-to-point
duplex auto
speed auto
mpls ip
service-policy output QOS_G_5
interface FastEthernet0/1.455
encapsulation dot1Q 455
xconnect 5.5.5.5 455 encapsulation mpls
service-policy input EF
PE2(6503 qos):
R1#show module
Mod Ports Card Type Model Serial No.
1 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAL09401U2L
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL114247YN
3 16 16 port 1000mb GBIC ethernet WS-X6416-GBIC SAL0712AM69
4 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL10019J4N
5 2 Supervisor Engine 720 (Hot) WS-SUP720-3BXL SAD102805VM
6 2 Supervisor Engine 720 (Active) WS-SUP720-BASE SAD0846060F
Mod Sub-Module Model Serial Hw Status
1 Distributed Forwarding Card WS-F6700-DFC3BXL SAD102504EF 5.3 Ok
2 Centralized Forwarding Card WS-F6700-CFC SAD111300PD 3.1 Ok
4 Centralized Forwarding Card WS-F6700-CFC SAL1004BQ2A 2.0 Ok
5 Policy Feature Card 3 WS-F6K-PFC3BXL SAD10270189 1.8 Ok
5 MSFC3 Daughterboard WS-SUP720 SAD102801G5 2.5 Ok
6 Policy Feature Card 3 WS-F6K-PFC3BXL SAL1415FE95 1.11 Ok
6 MSFC3 Daughterboard WS-SUP720 SAD08440794 2.4 Ok
R1#show mls qos maps
Normal Burst Policed-dscp map: (dscp= d1d2)
d1 : d2 0 1 2 3 4 5 6 7 8 9
0 : 01 01 02 03 04 05 06 07 08 09
1 : 10 11 12 13 14 15 16 17 18 19
2 : 20 21 22 23 24 25 26 27 28 29
3 : 30 31 32 33 34 35 36 37 38 39
4 : 40 41 42 43 44 45 01 47 48 49
5 : 50 51 52 53 54 55 56 57 58 59
6 : 60 61 62 63
Maximum Burst Policed-dscp map: (dscp= d1d2)
d1 : d2 0 1 2 3 4 5 6 7 8 9
0 : 00 01 02 03 04 05 06 07 08 09
1 : 10 11 12 13 14 15 16 17 18 19
2 : 20 21 22 23 24 25 26 27 28 29
3 : 30 31 32 33 34 35 36 37 38 39
4 : 40 41 42 43 44 45 46 47 48 49
5 : 50 51 52 53 54 55 56 57 58 59
6 : 60 61 62 63
Dscp-cos map: (dscp= d1d2)
d1 : d2 0 1 2 3 4 5 6 7 8 9
0 : 00 00 00 00 00 00 00 00 01 01
1 : 01 01 01 01 01 01 02 02 02 02
2 : 02 02 02 02 03 03 03 03 03 03
3 : 03 03 04 04 04 04 04 04 04 04
4 : 05 05 05 05 05 05 05 05 06 06
5 : 06 06 06 06 06 06 07 07 07 07
6 : 07 07 07 07
Dscp-exp map: (dscp= d1d2)
d1 : d2 0 1 2 3 4 5 6 7 8 9
0 : 00 00 00 00 00 00 00 00 01 01
1 : 01 01 01 01 01 01 02 02 02 02
2 : 02 02 02 02 03 03 03 03 03 03
3 : 03 03 04 04 04 04 04 04 04 04
4 : 05 05 05 05 05 05 05 05 06 06
5 : 06 06 06 06 06 06 07 07 07 07
6 : 07 07 07 07
Cos-dscp map:
cos: 0 1 2 3 4 5 6 7
dscp: 0 10 18 24 34 46 48 56
IpPrecedence-dscp map:
ipprec: 0 1 2 3 4 5 6 7
dscp: 0 8 16 24 32 40 48 56
Exp-dscp map:
exp: 0 1 2 3 4 5 6 7
dscp: 0 8 16 24 32 40 48 56
mls netflow interface
mls qos map cos-dscp 0 10 18 24 34 46 48 56
mls qos
class-map match-all exp_3
match mpls experimental topmost 3
class-map match-all EXP_5
match mpls experimental topmost 5
class-map match-all QOS_GROUP_5
match qos-group 5
class-map match-all prec5
match ip precedence 5
class-map match-all cos5
match cos 5
policy-map mpls2ip
class QOS_GROUP_5
set cos 5
policy-map IN_FROM_R3
class EXP_5
set qos-group 5
interface Loopback0
ip address 5.5.5.5 255.255.255.255
interface GigabitEthernet2/2
mls qos trust cos
or <------------ (tried both individually but none worked)
mls qos trust dscp
interface GigabitEthernet2/2.455
encapsulation dot1Q 455
xconnect 3.3.3.3 455 encapsulation mpls
service-policy output mpls2ip
interface GigabitEthernet2/1
ip address 192.168.34.4 255.255.255.0
ip ospf network point-to-point
mls qos trust cos
or <------------ (tried both individually but none worked)
mls qos trust dscp
mpls ip
service-policy input IN_FROM_R4
Thanks & regards,
Ahsan Rasheed

Hi All,.
I am still having issue on 6503 or 6524 Cisco Switch.
" Can any one give me any sample of 6524 or 6503 QOS working configuration, i would be really thankful "
As i have mentioned in my prevoius post of configuration of 6503. I am unable to match mpls exp 5 packet on 6503. My qos configuration on PE1(2811 router) is working perfectly. I am unable to classify mpls ex5 or mpls exp3 on 6503 switch. Am i missing something on configuration?
PE2 config:"6503 switch"
class-map match-all mpls_exp
match mpls experimental topmost 5
policy-map EF
class mpls_exp
R!#mls qos
int Gi2/4
service-policy input EF
mls qos trust cos
dscp: 0 10 18 24 34 46 48 56
Exp-dscp map:
exp: 0 1 2 3 4 5 6 7
dscp: 0 10 18 24 34 46 48 56
Thanks,
Ahsan Rasheed

Flash file location in 6500 Core switch

Hi ,
Please guide me what is location of flash file in 6500 Series switch and how can we take back of IOS image for 6500 series.
Thank you

You're welcome.
People seldom backup the actual IOS image binary file since it is usually just as easy to pull a new copy from cisco.com.
The more useful file is the running-config. You can most easily get a one time copy of that by just setting terminal length to 0 ("term len 0"), turning on logging on your shell tool and then typing "show run". The log file will now have a local copy of your running-config. You can also copy it via the cli using tftp, ftp, scp etc. transport methods.
Many open source and commercial products also allow you to automate that whole process for many devices. RANCID, Kiwi CatTools, SolarWinds NCM, Cisco Prime LMS, etc. all do that (and much more).
Please rate helpful posts and mark your question as answered when it is.

Which CISCO switch supports SFP, SFP+ and 10G ethernet ports

I would like to have information about a CISCO switch which can support fiber ports SFP(1g) and SFP+(10g) and copper 1g and 10g ethernet ports. And will it also software upgradable to support L3 protocols ?

You can choose from the Cisco 3560-E, 4900, 4500, and 6500 series switches. That's in order of capability (and cost!), from least to greatest.
The 3560-E and 4900 series are fixed chassis systems (the 4900M is semi-modular) while the 4500 and 6500 series are completely modular - buy the chassis and populate it according to your requirements.
In addition to the references cited above, also refer to the Cisco Products Quick Reference Guide (CPQRG), available at http://www.cisco.com/en/US/prod/qrg/index.html
Hope this helps. Please rate this post if it does.

NAC CCA - Designated Period

Hello,
I'm running a NAC solution (L2 OOB VG). I'm fine tuning the CCA section configuration on the CAM. I've selected 'audit' for my enforce type in the Requirements section, because I want to see all the reports whether my users are certified or not. Is it possible to configure the CAM to give my users a designated period (lets say 2wks) to get everything updated to get there PCs certified, if not they would be lock from getting access to the internal network?
-K

I think this Release Notes for Cisco NAC Appliance (Cisco Clean Access), clear your doubts for NAC/CCA issues.

Using TACACS+ With ACS 5.6 on 300 Series Switches v1.4

I was wondering if anyone could give me instructions on how to set up ACS for TACACS+ on a 300 series switch using Authorization? I can get it to work to authenticate, but the authorization doesn't seem to work like a catalyst switch. Thanks in advance for any help!

Brandon, thanks for the link, but this is for the older software before they included authorization (the v1.4). I've looked through a bunch of manuals and tried to find examples online, but it doesn't seem like anyone has anything out there I can find.

TACACS+ Authorization on 300 Series Switches

I was wondering if anyone could give me instructions on how to set up ACS for TACACS+ on a 300 series switch using Authorization? I can get it to work to authenticate, but the authorization doesn't seem to work like a catalyst switch. Thanks in advance for any help!

Brandon, thanks for the link, but this is for the older software before they included authorization (the v1.4). I've looked through a bunch of manuals and tried to find examples online, but it doesn't seem like anyone has anything out there I can find.

CCA for 100 + 300 series switches?

Is it in the roadmap to provide CCA control over 300 series switches? We have a lot of SRW2008's put in before the 8-port ESW existed...and we have PITA vlan consistency issues out there too that I think CCA would help fix.
While I understand the "don't pre-announce products", I need a level of design intent around CCA - is it a tool for configuring UC series pieces primarily and all else is secondary? Or is it the multi-device config tool for all SBCS pieces?

Nothing to do with the UC - primary concern is standalone networks.
Real life case:
2 ESW switches in control room hooked up to SA540
Closet switches are SRW2008's
Port no more than two devices are supposed to go now has 4, add an SRW2008 to the desk location.
Now, it turns out that there is a badly behaved device at the desk - a video player that spews all sorts of traffic when it's playing that doesn't play nice with others. So I now need to set-up a VLAN crossing those two switches. Oh, and it turns out the customer decided to unplug an access point and plug it into that switch too which ended up causing a loop when the PC plugged into ethernet someplace else attached to the PC.
Tasks:
Ensure that the 2 SRW2008's have proper vlan assignments to setup a port vlan for that video server.
Issues:
Make sure you assign proper configs to both ends of each link
Make sure not to confuse one SRW2008 with another
If new vlan, make sure all other ports that need to see it can still see it.
Applications for CCA:
Visualize all VLANS
Document port assignments (i.e. where is the video server vs. printer on that last leg 2008)
More easily see port statistics across multiple switches
So after I did that work, I realized that the SA540 wasn't really up to being an aggregation switch too and made the ESW-540-48 into the aggregation switch which required some more changes - however CCA made it easy...
At another job, I have SA540 + AP541ns (upgraded from RVL200 + WAP54GP's) but if I had 300 series in CCA, I'd upgrade the SRW2024's and SRW2008's but without easy management tools, the labor cost will be too high to make their networks really managed.....CCA makes that layer of management cheaper.

I need online Configuration Guide for Catalyst Express 500 Series Switches

Hi Mates,
Please is there an online help page for 500 series catalyst
I have this one for IOS 12.2(25)FY http://www.cisco.com/en/US/products/ps6545/products_configuration_example09186a00806da6c9.shtml
but I need more detailes like IOS 12.3(7)JA for Aironet 1300 http://www.cisco.com/en/US/products/ps5861/products_configuration_guide_book09186a00804ebd50.html
Regards
Saher

I'm afraid there is not such document for IOS 12.2(25)FY since the Catalyst Express 500 Series switches are manageable through the GUI Device Manager or Cisco Network Assistant.
I have also found key features and standards supported for that release:
http://www.cisco.com/en/US/products/sw/iosswrel/ps5012/prod_bulletin0900aecd8033b8b3.html
Hope this helps

Switch support for NAC CCA for 6500 series switch

Similar Messages

Maybe you are looking for