Synaptic touchpad detects hovering finger.
My synaptic touch pad can detect me finger even if it is hovering 2~3 mm (0.079~0.12 inches).
This happens only for two finger scroll.
If for example I am scrolling with the two finger and I lift the one finger in order to single click it is very likely to generate a middle click. If I lift the one finger uncomfortably high the problem doesn't occur.
Setting FingerLow, FingerHigh high (I can go to 75 before the touchpad becomes unusable) doesn't seem to help.
Any ideas?
If I lower FingerLow, FingerHigh values I can move the cursor from a distance of 1+ cm...
Similar Messages
-
For some time now my mouse hadnt been working so I was using an external mouse which worked correctly, but I gave the mouse out and I am trying to restore my touchpad on my computer so I went to the mouse property then I clicked on the software tab and realised there was no driver for my mouse.
Where can I find the synaptic touchpad drivers for Hp Pavilion dv7 2045eo? and If it is not a problem with the driver where can I find its solution?Dear Customer,
Welcome and Thank you for posting your query on HP Support Forum
It looks like you are facing difficulties with the Touchpad of your Notebook
We will surely assist you with this
Steps to drain the Static charge and loading default BIOS settings to resolve the issue
Step 01. Turn OFF the Notebook
Step 02. Un-plug the Power/AC Adapter and also remove the Battery too
Step 03. Press and Hold the Power Button of the Notebook for a full minute
Step 04. Now let's re-insert the battery back in and plug back the Power/AC Adapter
Step 05. Start the Notebook and keep tapping F10 Key during the startup to access the BIOS
Step 06. Once you get to the BIOS, Please press F5 Key to load setup defaults for the BIOS
Step 07. Now let's press Esc/Escape Key. Save Changes and Exit - Yes
Step 08. Now please wait till the Unit loads the Windows Operating system
Now please re-install the touchpad drivers from HP Website in order to resolve the issue
Hope this helps, for any further queries reply to the post and feel free to join us again
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
K N R K
Although I am an HP employee, I am speaking for myself and not for HP -
Touch I'd isn't detecting my finger
I updated my iphone to iOS 7.1. Before updating also I had problem with touch I'd. But now its worser. It is not even detecting my finger. Can you tell me what to do. My hands and reader was clean before enrolling. Tried resetting too.
Hey Khasifmkhan,
Thanks for the question, and great troubleshooting so far. I understand you are experiencing issues with Touch ID. The following article provides some troubleshooting steps that may be helpful:
iPhone 5s: Using Touch ID
http://support.apple.com/kb/HT5883
Resolving issues with Touch ID
1. Verify that you are using the latest version of iOS.
2. Ensure that your fingers and the Home button are clean and dry.*
Note: Cover the Home button completely. Don't tap too quickly, don't press down hard, and don't move your finger while Touch ID is scanning. Make sure that your finger touches the metal ring around the Home button.
3. If you are using a protective case or screen protector, it must leave the Home button and the surrounding ring completely unobscured. If it doesn't, remove the case or screen protector and try again.
4. Tap Settings > Touch ID & Passcode and verify that:
- iPhone Unlock or iTunes & App Store is enabled.
- One or more fingerprints have been enrolled.
5. If one finger isn't working, tap Edit in Settings > Touch ID & Passcode to delete and then reenroll the finger.
6. If that finger still isn't working, try enrolling a different finger.
7. If you are unable to enroll any of your fingers, take your iPhone 5s to an Apple Retail Store, Apple Authorized Service Provider, or contact AppleCare for further assistance.
* Moisture, lotions, sweat, oils, cuts, or dry skin may affect fingerprint recognition. Certain activities can also temporarily affect fingerprint recognition, including exercising, showering, swimming, cooking, or other conditions or changes that affect your fingerprint.
Thanks,
Matt M. -
Synaptic TouchPad is deactivated upon Windows 7 Startup
Hello Everybody
I am using Lenovo G430 4152-C5Q Laptop.
I have been using Windows 7 RC since two months.
Today i updated all the software and drivers to Windows 7 Versions after noticing it in Lenovo support page.
Now Synaptic TouchPad is not working upon Windows 7 Startup.
Everytime i have to enable / disable TouchPad using the function keys to use it.
But if i uninstall the Synaptic TouchPad driver, the TouchPad is working well automatically upon every Windows 7 startup.
But don't recommend that option as Windows 7 Built-In driver is not utilizing all features of the TouchPad.Yeah, i am very sure.
As Alps was unable to provide any additional features to my touchpad.
Moreover i am able to utilize all the features supported by the Synaptic driver. -
HP g6-1b68nr NEED SYNAPTIC TOUCHPAD INFO
SYNAPTIC TOUCHPAD ADVICE FOR g6-1b68nr -- Laptops still function great! EXCEPT---
It's 3 yrs since I purchsed 2 exactly the same g6-1b68nr Pavilion Notebooks. One I used myself and it has SYNAPTIC TOUCHPAD functions intact; works great.
The other I just started using again (differnt house) but Synptics are missing even in the Search menu.
Looking for the right HP or other safe link, to reinstall software or maybe, all that's needed is Driver Update? Not sure.
Thnx for any advice. Today is 10 Dec. 2014
This question was solved.
View Solution.Hi:
Below is the link to the support and driver page for your notebook.
http://h10025.www1.hp.com/ewfrf/wc/product?cc=us&dlc=en&lc=en&os=4063&product=5128912&sw_lang=
The touchpad driver can be found under the keyboard and mouse driver section for the operating system you are running. -
Scrolling Synaptic Touchpad Problem (Arch Wiki didn't solve it)
Good to the whole Arch's community.
First of all to appear, I am codebuster and am new in this community and in this magnificent distro that I have been charmed with for his simplicity and performance. Always I had begun for behind the topic of the configuration of Arch's installation, but consulting his magnificent tips and coming to the official information it me has been possible. I have everything working of correct form except the function of scroll of my touchpad Synaptic (function that I use always and that really I throw enough in lack). I have followed the steps indicated so much in the Wiki (http://wiki.archlinux.org/index.php/Touchpad_Synaptics) as in numerous forums of linux in inet but I have not managed to make it work, for what I resort to you to seeing if someone can throw something of light.
Let's begin.
PC: Acer Aspire 5610
Distribution: ArchLinux updated a today.
Desktop: XFCE
Graphics: NVIDIA Geforce GO 7300 (proprietary Drivers: NVIDIA Driver Version:256.35)
Driver: xf86-input-synaptics-1.2.2-2
hardinfo
Name PS/2 Synaptics TouchPad
Type Mouse
Bus 0x11
Vendor 2
Product 0x1
Version 0x0
Connected to isa0060/serio/input0
cat /proc/bus/input/devices
I: Bus=0011 Vendor=0002 Product=0001 Version=0000
N: Name="PS/2 Synaptics TouchPad"
P: Phys=isa0060/serio4/input0
S: Sysfs=/devices/platform/i8042/serio4/input/input5
U: Uniq=
H: Handlers=mouse0 event5
B: EV=7
B: KEY=70000 0 0 0 0 0 0 0 0
B: REL=3
xorg.conf
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:59 PDT 2010
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/TTF/"
FontPath "/usr/share/fonts/OTF/"
FontPath "/usr/share/fonts/Type1/"
FontPath "/usr/share/fonts/100dpi/"
FontPath "/usr/share/fonts/75dpi/"
EndSection
Section "Module"
Load "dri2"
Load "dbe"
Load "record"
Load "glx"
Load "extmod"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mouse0"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
Identifier "Card0"
Driver "nvidia"
VendorName "nVidia Corporation"
BoardName "G72M [Quadro NVS 110M/GeForce Go 7300]"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Xorg.0.log
[ 18.827]
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
[ 18.828]
X.Org X Server 1.8.1.902 (1.8.2 RC 2)
Release Date: 2010-06-21
[ 18.828] X Protocol Version 11, Revision 0
[ 18.828] Build Operating System: Linux 2.6.34-ARCH i686
[ 18.828] Current Operating System: Linux arch-live 2.6.34-ARCH #1 SMP PREEMPT Mon Jul 5 21:03:38 UTC 2010 i686
[ 18.828] Kernel command line: root=/dev/disk/by-uuid/2cf26781-3ca3-4654-8b83-37ea60864aab ro
[ 18.828] Build Date: 21 June 2010 11:54:27AM
[ 18.828]
[ 18.829] Current version of pixman: 0.18.2
[ 18.830] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 18.830] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 18.830] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Jul 26 15:21:50 2010
[ 18.909] (==) Using config file: "/etc/X11/xorg.conf"
[ 18.909] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 18.962] (==) ServerLayout "X.org Configured"
[ 18.962] (**) |-->Screen "Screen0" (0)
[ 18.962] (**) | |-->Monitor "Monitor0"
[ 18.963] (**) | |-->Device "Card0"
[ 18.963] (**) |-->Input Device "Mouse0"
[ 18.963] (**) |-->Input Device "Keyboard0"
[ 18.963] (==) Automatically adding devices
[ 18.963] (==) Automatically enabling devices
[ 19.052] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 19.052] Entry deleted from font path.
[ 19.063] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 19.063] Entry deleted from font path.
[ 19.063] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 19.064] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 19.064] Entry deleted from font path.
[ 19.064] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 19.064] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 19.064] Entry deleted from font path.
[ 19.064] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 19.064] Entry deleted from font path.
[ 19.064] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 19.064] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 19.064] Entry deleted from font path.
[ 19.064] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 19.064] (**) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/,
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 19.064] (**) ModulePath set to "/usr/lib/xorg/modules"
[ 19.064] (WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 19.064] (WW) Disabling Mouse0
[ 19.064] (WW) Disabling Keyboard0
[ 19.064] (II) Loader magic: 0x81e9d00
[ 19.064] (II) Module ABI versions:
[ 19.064] X.Org ANSI C Emulation: 0.4
[ 19.064] X.Org Video Driver: 7.0
[ 19.064] X.Org XInput driver : 9.0
[ 19.064] X.Org Server Extension : 3.0
[ 19.088] (--) PCI:*(0:1:0:0) 10de:01d7:1025:0090 nVidia Corporation G72M [Quadro NVS 110M/GeForce Go 7300] rev 161, Mem @ 0xd1000000/16777216, 0xc0000000/268435456, 0xd0000000/16777216
[ 19.088] (II) Open ACPI successful (/var/run/acpid.socket)
[ 19.088] (II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
[ 19.088] (II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
[ 19.088] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
[ 19.088] (II) "record" will be loaded. This was enabled by default and also specified in the config file.
[ 19.088] (II) "dri" will be loaded by default.
[ 19.088] (II) "dri2" will be loaded. This was enabled by default and also specified in the config file.
[ 19.088] (II) LoadModule: "dri2"
[ 19.141] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 19.175] (II) Module dri2: vendor="X.Org Foundation"
[ 19.175] compiled for 1.8.1.902, module version = 1.2.0
[ 19.175] ABI class: X.Org Server Extension, version 3.0
[ 19.176] (II) Loading extension DRI2
[ 19.176] (II) LoadModule: "dbe"
[ 19.176] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 19.187] (II) Module dbe: vendor="X.Org Foundation"
[ 19.187] compiled for 1.8.1.902, module version = 1.0.0
[ 19.187] Module class: X.Org Server Extension
[ 19.187] ABI class: X.Org Server Extension, version 3.0
[ 19.187] (II) Loading extension DOUBLE-BUFFER
[ 19.187] (II) LoadModule: "record"
[ 19.187] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 19.188] (II) Module record: vendor="X.Org Foundation"
[ 19.188] compiled for 1.8.1.902, module version = 1.13.0
[ 19.188] Module class: X.Org Server Extension
[ 19.188] ABI class: X.Org Server Extension, version 3.0
[ 19.188] (II) Loading extension RECORD
[ 19.188] (II) LoadModule: "glx"
[ 19.189] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 20.431] (II) Module glx: vendor="NVIDIA Corporation"
[ 20.431] compiled for 4.0.2, module version = 1.0.0
[ 20.431] Module class: X.Org Server Extension
[ 20.431] (II) NVIDIA GLX Module 256.35 Wed Jun 16 19:21:24 PDT 2010
[ 20.431] (II) Loading extension GLX
[ 20.431] (II) LoadModule: "extmod"
[ 20.432] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 20.441] (II) Module extmod: vendor="X.Org Foundation"
[ 20.441] compiled for 1.8.1.902, module version = 1.0.0
[ 20.441] Module class: X.Org Server Extension
[ 20.441] ABI class: X.Org Server Extension, version 3.0
[ 20.441] (II) Loading extension MIT-SCREEN-SAVER
[ 20.441] (II) Loading extension XFree86-VidModeExtension
[ 20.441] (II) Loading extension XFree86-DGA
[ 20.441] (II) Loading extension DPMS
[ 20.441] (II) Loading extension XVideo
[ 20.441] (II) Loading extension XVideo-MotionCompensation
[ 20.441] (II) Loading extension X-Resource
[ 20.441] (II) LoadModule: "dri"
[ 20.442] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 20.451] (II) Module dri: vendor="X.Org Foundation"
[ 20.451] compiled for 1.8.1.902, module version = 1.0.0
[ 20.451] ABI class: X.Org Server Extension, version 3.0
[ 20.451] (II) Loading extension XFree86-DRI
[ 20.451] (II) LoadModule: "nvidia"
[ 20.452] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 20.560] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 20.560] compiled for 4.0.2, module version = 1.0.0
[ 20.560] Module class: X.Org Video Driver
[ 20.620] (II) NVIDIA dlloader X Driver 256.35 Wed Jun 16 18:59:34 PDT 2010
[ 20.625] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 20.625] (++) using VT number 7
[ 20.629] (II) Primary Device is: PCI 01@00:00:0
[ 20.645] (II) Loading sub module "fb"
[ 20.646] (II) LoadModule: "fb"
[ 20.654] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 20.675] (II) Module fb: vendor="X.Org Foundation"
[ 20.675] compiled for 1.8.1.902, module version = 1.0.0
[ 20.675] ABI class: X.Org ANSI C Emulation, version 0.4
[ 20.675] (II) Loading sub module "wfb"
[ 20.675] (II) LoadModule: "wfb"
[ 20.676] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 20.694] (II) Module wfb: vendor="X.Org Foundation"
[ 20.694] compiled for 1.8.1.902, module version = 1.0.0
[ 20.694] ABI class: X.Org ANSI C Emulation, version 0.4
[ 20.694] (II) Loading sub module "ramdac"
[ 20.694] (II) LoadModule: "ramdac"
[ 20.694] (II) Module "ramdac" already built-in
[ 20.744] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
[ 20.744] (==) NVIDIA(0): RGB weight 888
[ 20.744] (==) NVIDIA(0): Default visual is TrueColor
[ 20.744] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 20.744] (**) NVIDIA(0): Enabling RENDER acceleration
[ 20.744] (II) NVIDIA(0): Support for GLX with the Damage and Composite X extensions is
[ 20.744] (II) NVIDIA(0): enabled.
[ 22.341] (II) NVIDIA(0): NVIDIA GPU GeForce Go 7300 (G72) at PCI:1:0:0 (GPU-0)
[ 22.341] (--) NVIDIA(0): Memory: 262144 kBytes
[ 22.341] (--) NVIDIA(0): VideoBIOS: 05.72.22.58.30
[ 22.341] (II) NVIDIA(0): Detected PCI Express Link width: 16X
[ 22.341] (--) NVIDIA(0): Interlaced video modes are supported on this GPU
[ 22.341] (--) NVIDIA(0): Connected display device(s) on GeForce Go 7300 at PCI:1:0:0:
[ 22.341] (--) NVIDIA(0): LPL (DFP-0)
[ 22.341] (--) NVIDIA(0): LPL (DFP-0): 330.0 MHz maximum pixel clock
[ 22.341] (--) NVIDIA(0): LPL (DFP-0): Internal Dual Link LVDS
[ 22.355] (II) NVIDIA(0): Assigned Display Device: DFP-0
[ 22.355] (==) NVIDIA(0):
[ 22.355] (==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
[ 22.355] (==) NVIDIA(0): will be used as the requested mode.
[ 22.355] (==) NVIDIA(0):
[ 22.355] (II) NVIDIA(0): Validated modes:
[ 22.355] (II) NVIDIA(0): "nvidia-auto-select"
[ 22.356] (II) NVIDIA(0): Virtual screen size determined to be 1280 x 800
[ 22.356] (--) NVIDIA(0): DPI set to (98, 96); computed from "UseEdidDpi" X config
[ 22.356] (--) NVIDIA(0): option
[ 22.356] (==) NVIDIA(0): Enabling 32-bit ARGB GLX visuals.
[ 22.356] (--) Depth 24 pixmap format is 32 bpp
[ 22.358] (II) NVIDIA(0): Initialized GPU GART.
[ 22.371] (II) NVIDIA(0): ACPI display change hotkey events enabled: the X server is new
[ 22.371] (II) NVIDIA(0): enough to receive ACPI hotkey events.
[ 22.371] (WW) NVIDIA(0): ACPI: Error: Unable to find the brightness file path under
[ 22.372] (WW) NVIDIA(0): /proc/acpi/video. The NVIDIA X driver will not be able to
[ 22.372] (WW) NVIDIA(0): respond to ACPI brightness change hotkey events.
[ 22.372] (II) NVIDIA(0): Setting mode "nvidia-auto-select"
[ 23.783] (II) Loading extension NV-GLX
[ 23.817] (II) NVIDIA(0): Initialized OpenGL Acceleration
[ 23.831] (==) NVIDIA(0): Disabling shared memory pixmaps
[ 23.831] (II) NVIDIA(0): Initialized X Rendering Acceleration
[ 23.851] (==) NVIDIA(0): Backing store disabled
[ 23.851] (==) NVIDIA(0): Silken mouse enabled
[ 23.858] (==) NVIDIA(0): DPMS enabled
[ 23.858] (II) Loading extension NV-CONTROL
[ 23.859] (II) Loading extension XINERAMA
[ 23.859] (II) Loading sub module "dri2"
[ 23.859] (II) LoadModule: "dri2"
[ 23.860] (II) Reloading /usr/lib/xorg/modules/extensions/libdri2.so
[ 23.860] (II) NVIDIA(0): [DRI2] Setup complete
[ 23.860] (II) NVIDIA(0): [DRI2] VDPAU driver: nvidia
[ 23.860] (==) RandR enabled
[ 23.860] (II) Initializing built-in extension Generic Event Extension
[ 23.860] (II) Initializing built-in extension SHAPE
[ 23.860] (II) Initializing built-in extension MIT-SHM
[ 23.860] (II) Initializing built-in extension XInputExtension
[ 23.860] (II) Initializing built-in extension XTEST
[ 23.860] (II) Initializing built-in extension BIG-REQUESTS
[ 23.860] (II) Initializing built-in extension SYNC
[ 23.860] (II) Initializing built-in extension XKEYBOARD
[ 23.860] (II) Initializing built-in extension XC-MISC
[ 23.860] (II) Initializing built-in extension SECURITY
[ 23.860] (II) Initializing built-in extension XINERAMA
[ 23.860] (II) Initializing built-in extension XFIXES
[ 23.860] (II) Initializing built-in extension RENDER
[ 23.860] (II) Initializing built-in extension RANDR
[ 23.860] (II) Initializing built-in extension COMPOSITE
[ 23.860] (II) Initializing built-in extension DAMAGE
[ 23.864] (II) Initializing extension GLX
[ 24.465] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[ 24.465] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 24.465] (II) LoadModule: "evdev"
[ 24.466] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 24.483] (II) Module evdev: vendor="X.Org Foundation"
[ 24.483] compiled for 1.8.0, module version = 2.4.0
[ 24.483] Module class: X.Org XInput Driver
[ 24.483] ABI class: X.Org XInput driver, version 9.0
[ 24.483] (**) Power Button: always reports core events
[ 24.483] (**) Power Button: Device: "/dev/input/event4"
[ 24.491] (II) Power Button: Found keys
[ 24.491] (II) Power Button: Configuring as keyboard
[ 24.491] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 24.491] (**) Option "xkb_rules" "evdev"
[ 24.491] (**) Option "xkb_model" "evdev"
[ 24.491] (**) Option "xkb_layout" "us"
[ 24.579] (II) config/udev: Adding input device Video Bus (/dev/input/event5)
[ 24.580] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 24.580] (**) Video Bus: always reports core events
[ 24.580] (**) Video Bus: Device: "/dev/input/event5"
[ 24.587] (II) Video Bus: Found keys
[ 24.587] (II) Video Bus: Configuring as keyboard
[ 24.587] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
[ 24.587] (**) Option "xkb_rules" "evdev"
[ 24.587] (**) Option "xkb_model" "evdev"
[ 24.587] (**) Option "xkb_layout" "us"
[ 24.593] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[ 24.594] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 24.594] (**) Power Button: always reports core events
[ 24.594] (**) Power Button: Device: "/dev/input/event3"
[ 24.600] (II) Power Button: Found keys
[ 24.600] (II) Power Button: Configuring as keyboard
[ 24.600] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 24.600] (**) Option "xkb_rules" "evdev"
[ 24.601] (**) Option "xkb_model" "evdev"
[ 24.601] (**) Option "xkb_layout" "us"
[ 24.602] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[ 24.602] (II) No input driver/identifier specified (ignoring)
[ 24.602] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)
[ 24.602] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 24.602] (**) Sleep Button: always reports core events
[ 24.602] (**) Sleep Button: Device: "/dev/input/event2"
[ 24.611] (II) Sleep Button: Found keys
[ 24.611] (II) Sleep Button: Configuring as keyboard
[ 24.611] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD)
[ 24.611] (**) Option "xkb_rules" "evdev"
[ 24.611] (**) Option "xkb_model" "evdev"
[ 24.611] (**) Option "xkb_layout" "us"
[ 24.613] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event8)
[ 24.613] (II) No input driver/identifier specified (ignoring)
[ 24.619] (II) config/udev: Adding input device MosArt Optical Mouse (/dev/input/event7)
[ 24.619] (**) MosArt Optical Mouse: Applying InputClass "evdev pointer catchall"
[ 24.619] (**) MosArt Optical Mouse: always reports core events
[ 24.619] (**) MosArt Optical Mouse: Device: "/dev/input/event7"
[ 24.631] (II) MosArt Optical Mouse: Found 3 mouse buttons
[ 24.631] (II) MosArt Optical Mouse: Found scroll wheel(s)
[ 24.631] (II) MosArt Optical Mouse: Found relative axes
[ 24.631] (II) MosArt Optical Mouse: Found x and y relative axes
[ 24.631] (II) MosArt Optical Mouse: Configuring as mouse
[ 24.631] (**) MosArt Optical Mouse: YAxisMapping: buttons 4 and 5
[ 24.631] (**) MosArt Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 24.631] (II) XINPUT: Adding extended input device "MosArt Optical Mouse" (type: MOUSE)
[ 24.631] (**) MosArt Optical Mouse: (accel) keeping acceleration scheme 1
[ 24.631] (**) MosArt Optical Mouse: (accel) acceleration profile 0
[ 24.631] (**) MosArt Optical Mouse: (accel) acceleration factor: 2.000
[ 24.631] (**) MosArt Optical Mouse: (accel) acceleration threshold: 4
[ 24.631] (II) MosArt Optical Mouse: initialized for relative axes.
[ 24.632] (II) config/udev: Adding input device MosArt Optical Mouse (/dev/input/mouse1)
[ 24.632] (II) No input driver/identifier specified (ignoring)
[ 24.638] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 24.638] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 24.638] (**) AT Translated Set 2 keyboard: always reports core events
[ 24.638] (**) AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 24.651] (II) AT Translated Set 2 keyboard: Found keys
[ 24.651] (II) AT Translated Set 2 keyboard: Configuring as keyboard
[ 24.651] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
[ 24.651] (**) Option "xkb_rules" "evdev"
[ 24.651] (**) Option "xkb_model" "evdev"
[ 24.651] (**) Option "xkb_layout" "us"
[ 24.652] (II) config/udev: Adding input device PS/2 Synaptics TouchPad (/dev/input/event6)
[ 24.652] (**) PS/2 Synaptics TouchPad: Applying InputClass "evdev pointer catchall"
[ 24.652] (**) PS/2 Synaptics TouchPad: always reports core events
[ 24.652] (**) PS/2 Synaptics TouchPad: Device: "/dev/input/event6"
[ 24.664] (II) PS/2 Synaptics TouchPad: Found 3 mouse buttons
[ 24.664] (II) PS/2 Synaptics TouchPad: Found relative axes
[ 24.664] (II) PS/2 Synaptics TouchPad: Found x and y relative axes
[ 24.664] (II) PS/2 Synaptics TouchPad: Configuring as mouse
[ 24.664] (**) PS/2 Synaptics TouchPad: YAxisMapping: buttons 4 and 5
[ 24.664] (**) PS/2 Synaptics TouchPad: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 24.664] (II) XINPUT: Adding extended input device "PS/2 Synaptics TouchPad" (type: MOUSE)
[ 24.664] (**) PS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 24.664] (**) PS/2 Synaptics TouchPad: (accel) acceleration profile 0
[ 24.664] (**) PS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 24.664] (**) PS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 24.664] (II) PS/2 Synaptics TouchPad: initialized for relative axes.
[ 24.665] (II) config/udev: Adding input device PS/2 Synaptics TouchPad (/dev/input/mouse0)
[ 24.665] (II) No input driver/identifier specified (ignoring)
10-evdev.conf
# Catchall classes for input devices
# We don't simply match on any device since that also adds accelerometers
# and other devices that we don't really want to use. The list below
# matches everything but joysticks.
Section "InputClass"
Identifier "evdev pointer catchall"
MatchIsPointer "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
Section "InputClass"
Identifier "evdev keyboard catchall"
MatchIsKeyboard "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
Section "InputClass"
Identifier "evdev touchpad catchall"
MatchIsTouchpad "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
Option "VertEdgeScroll" "true"
Option "VertScrollDelta" "100"
EndSection
Section "InputClass"
Identifier "evdev tablet catchall"
MatchIsTablet "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
Section "InputClass"
Identifier "evdev touchscreen catchall"
MatchIsTouchscreen "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
10-synaptics.conf
Section "InputClass"
Identifier "touchpad catchall"
Driver "synaptics"
MatchIsTouchpad "on"
Option "TapButton1" "1"
Option "TapButton2" "2"
Option "TapButton3" "3"
Option "VertEdgeScroll" "true"
Option "VertScrollDelta" "100"
EndSection
Good, I believe that this is quite, if you need more information tell to me and it will make it come near.
Excuse me for my poor english,Thanks in advance and best regards.
codebuster.
Last edited by codebuster (2010-07-26 14:44:07)kgas wrote:
there is no need to include the synaptics option. here is mine and works fine (Acer Aspire 5738G)
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "dbe"
Load "glx"
Load "dri"
Load "dri2"
Load "extmod"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
Identifier "Card0"
Driver "nvidia"
VendorName "nVidia Corporation"
BoardName "G98M [GeForce G 105M]"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
¡¡¡¡ Thanks a lot for the info !!!
I remove all the Synaptics entries in the xorg.conf and worked fine with the /dev/input/mice option (in the Arch Wiki was # commented, the device, was /dev/psaux, and my mouse in hardinfo was recognized as PS/2 Synaptic for that I thought that it was the correct option ).
Only one question, now I have set the scrolling mode with two fingers, ¿do you know how to activate one finger scrolling? I tried with these options in Mouse section but doesn't work for me:
Option "VertEdgeScroll" "true" # enable vertical scroll zone
Option "HorizEdgeScroll" "false" # enable horizontal scroll zone
Option "VertTwoFingerScroll" "false" # vertical scroll anywhere with two fingers
Option "HorizTwoFingerScroll" "false" # horizontal scroll anywhere with two fingers
¡ Many, many thanks and my best regards !
codebuster.
Last edited by codebuster (2010-07-26 08:26:55) -
[SOLVED] Touchpad detected as keyboard
Since some week back, most probably because of some update my touchpad stopped working correctly. It's like all the extra functions are gone since there is no scrolling, no tapfunction, and it's extremly sensitive.
I've read some of the threads on the forum and tried the solutions but found nothing to work. What I've tried:
1. Comment out the touchpad in /etx/X11/xorg.conf.d/10-evdev.conf
2. Remove /etc/X11/xorg.conf
3. Update udev to 168
4. None of the changes I make to /etc/X11/xorg.conf.d/10-synaptics.conf seem to have any effect at all on the touchpad.
The configuration now is:
/etc/X11/xorg.conf.d/10-evdev.conf
Section "InputClass"
Identifier "evdev pointer catchall"
MatchIsPointer "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
Section "InputClass"
Identifier "evdev keyboard catchall"
MatchIsKeyboard "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
Section "InputClass"
Identifier "evdev touchpad catchall"
MatchIsTouchpad "on"
MatchDevicePath "/dev/input/event*"
Driver "synaptic"
EndSection
Section "InputClass"
Identifier "evdev tablet catchall"
MatchIsTablet "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
Section "InputClass"
Identifier "evdev touchscreen catchall"
MatchIsTouchscreen "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
/etx/X11/xorg.conf.d/10-synaptic.conf
Section "InputClass"
Identifier "touchpad catchall"
Driver "synaptics"
MatchDevicePath "/dev/input/event*"
MatchIsTouchpad "on"
Option "TapButton1" "1"
Option "TapButton2" "2"
Option "TapButton3" "3"
Option "VertEdgeScroll" "on"
EndSection
And the lines from xorg log containing synaptic:
[ 705.427] (II) config/udev: Adding input device Sleep Button (/dev/input/event4)
[ 705.427] (**) Sleep Button: Applying InputClass "evdev touchpad catchall"
[ 705.427] (**) Sleep Button: Applying InputClass "touchpad catchall"
[ 705.427] (II) LoadModule: "synaptics"
[ 705.428] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 705.428] (II) Module synaptics: vendor="X.Org Foundation"
[ 705.428] compiled for 1.10.0, module version = 1.4.0
[ 705.428] Module class: X.Org XInput Driver
[ 705.428] ABI class: X.Org XInput driver, version 12.2
[ 705.428] (II) Using input driver 'synaptics' for 'Sleep Button'
[ 705.428] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 705.428] (**) Sleep Button: always reports core events
[ 705.428] (**) Option "Device" "/dev/input/event4"
[ 705.560] (--) Sleep Button: invalid x-axis range. defaulting to 1615 - 5685
[ 705.560] (--) Sleep Button: invalid y-axis range. defaulting to 1729 - 4171
[ 705.560] (--) Sleep Button: invalid pressure range. defaulting to 0 - 256
[ 705.560] (--) Sleep Button: invalid finger width range. defaulting to 0 - 16
[ 705.560] (**) Option "VertEdgeScroll" "on"
[ 705.560] (**) Option "TapButton1" "1"
[ 705.560] (**) Option "TapButton2" "2"
[ 705.560] (**) Option "TapButton3" "3"
[ 705.666] (--) Sleep Button: no supported touchpad found
[ 705.666] (EE) Sleep Button Unable to query/initialize Synaptics hardware.
[ 705.720] (EE) PreInit returned 11 for "Sleep Button"
[ 705.720] (II) UnloadModule: "synaptics"
[ 705.720] (II) Unloading synaptics
[ 705.827] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event7)
[ 705.827] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev keyboard catchall"
[ 705.827] (II) Using input driver 'evdev' for 'SynPS/2 Synaptics TouchPad'
[ 705.827] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 705.827] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 705.827] (**) SynPS/2 Synaptics TouchPad: Device: "/dev/input/event7"
[ 705.853] (--) SynPS/2 Synaptics TouchPad: Found 3 mouse buttons
[ 705.853] (--) SynPS/2 Synaptics TouchPad: Found absolute axes
[ 705.853] (--) SynPS/2 Synaptics TouchPad: Found x and y absolute axes
[ 705.853] (--) SynPS/2 Synaptics TouchPad: Found absolute touchpad.
[ 705.853] (II) SynPS/2 Synaptics TouchPad: Configuring as touchpad
[ 705.853] (**) SynPS/2 Synaptics TouchPad: YAxisMapping: buttons 4 and 5
[ 705.853] (**) SynPS/2 Synaptics TouchPad: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 705.853] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input7/event7"
[ 705.853] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
[ 705.853] (II) SynPS/2 Synaptics TouchPad: initialized for absolute axes.
[ 705.853] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 705.853] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 0
[ 705.853] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 705.853] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 705.854] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse0)
[ 705.854] (II) No input driver/identifier specified (ignoring)
[ 705.854] (II) config/udev: Adding input device PC Speaker (/dev/input/event1)
[ 705.854] (II) No input driver/identifier specified (ignoring)
Last edited by Larsson (2011-04-29 12:09:08)Temporarily solved the problem. It was as I suspected, the touchpad was detected as a keyboard and therefor loaded the evdev driver as seen in xorg.log. So I changed the /etx/X11/xorg.conf.d/10-synaptic.conf to match keyboard instead and only for the specific event named in xorg.log.
So /etx/X11/xorg.conf.d/10-synaptic.conf:
Section "InputClass"
Identifier "touchpad catchall"
Driver "synaptics"
MatchIsKeyboard "on"
MatchDevicePath "/dev/input/event7"
Option "TapButton1" "1"
Option "TapButton2" "2"
Option "TapButton3" "3
Option "VertEdgeScroll" "on"
EndSection
Last edited by Larsson (2011-04-29 12:08:21) -
Touchpad detected as PS/2 Logitech Wheel Mouse
Hi,
The touchpad on my Asus U46SV laptop is being detected as a PS/2 Logitech Wheel Mouse. Therefore no touchpad driver is loaded and all fancy features (two-finger scrolling, disable while typing, etc) are unavailable. How can I fix this?
$ xinput list
⎡ Virtual core pointer id=2 [master pointer (3)]
⎜ ↳ Virtual core XTEST pointer id=4 [slave pointer (2)]
⎜ ↳ PS/2 Logitech Wheel Mouse id=13 [slave pointer (2)]
⎣ Virtual core keyboard id=3 [master keyboard (2)]
↳ Virtual core XTEST keyboard id=5 [slave keyboard (3)]
↳ Power Button id=6 [slave keyboard (3)]
↳ Video Bus id=7 [slave keyboard (3)]
↳ Video Bus id=8 [slave keyboard (3)]
↳ Sleep Button id=9 [slave keyboard (3)]
↳ ASUS USB2.0 WebCam id=10 [slave keyboard (3)]
↳ Asus WMI hotkeys id=11 [slave keyboard (3)]
↳ AT Translated Set 2 keyboard id=12 [slave keyboard (3)]
$ dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0-ARCH (tobias@T-POWA-LX) (gcc version 4.6.1 (GCC) ) #1 SMP PREEMPT Tue Aug 16 08:44:20 CEST 2011
[ 0.000000] Command line: root=/dev/disk/by-uuid/f3bdc9ce-59f4-42c8-98cd-bacdc7803d59 ro
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
[ 0.000000] BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
[ 0.000000] BIOS-e820: 0000000020000000 - 0000000020200000 (reserved)
[ 0.000000] BIOS-e820: 0000000020200000 - 0000000040000000 (usable)
[ 0.000000] BIOS-e820: 0000000040000000 - 0000000040200000 (reserved)
[ 0.000000] BIOS-e820: 0000000040200000 - 00000000aabcc000 (usable)
[ 0.000000] BIOS-e820: 00000000aabcc000 - 00000000aacdf000 (reserved)
[ 0.000000] BIOS-e820: 00000000aacdf000 - 00000000aace1000 (usable)
[ 0.000000] BIOS-e820: 00000000aace1000 - 00000000aacf4000 (reserved)
[ 0.000000] BIOS-e820: 00000000aacf4000 - 00000000aacf5000 (usable)
[ 0.000000] BIOS-e820: 00000000aacf5000 - 00000000aade8000 (reserved)
[ 0.000000] BIOS-e820: 00000000aade8000 - 00000000aaf19000 (usable)
[ 0.000000] BIOS-e820: 00000000aaf19000 - 00000000aafe8000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000aafe8000 - 00000000aaffd000 (usable)
[ 0.000000] BIOS-e820: 00000000aaffd000 - 00000000ab000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000ab000000 - 00000000afa00000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000e4000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff980000 - 00000000ffc00000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffd80000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 000000014fe00000 (usable)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.7 present.
[ 0.000000] DMI: ASUSTeK Computer Inc. U46SV/U46SV, BIOS U46SV.203 06/09/2011
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x14fe00 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FE0000000 write-back
[ 0.000000] 2 base 0A0000000 mask FF8000000 write-back
[ 0.000000] 3 base 0A8000000 mask FFC000000 write-back
[ 0.000000] 4 base 0AB000000 mask FFF000000 uncachable
[ 0.000000] 5 base 100000000 mask FC0000000 write-back
[ 0.000000] 6 base 140000000 mask FF0000000 write-back
[ 0.000000] 7 base 14FE00000 mask FFFE00000 uncachable
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 00000000ab000000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0xaaffd max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [ffff8800000fcc70] fcc70
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 20480
[ 0.000000] init_memory_mapping: 0000000000000000-00000000aaffd000
[ 0.000000] 0000000000 - 00aae00000 page 2M
[ 0.000000] 00aae00000 - 00aaffd000 page 4k
[ 0.000000] kernel direct mapping tables up to aaffd000 @ aaff8000-aaffd000
[ 0.000000] init_memory_mapping: 0000000100000000-000000014fe00000
[ 0.000000] 0100000000 - 014fe00000 page 2M
[ 0.000000] kernel direct mapping tables up to 14fe00000 @ 14fdf9000-14fe00000
[ 0.000000] RAMDISK: 1fda0000 - 1fff0000
[ 0.000000] ACPI: RSDP 00000000000f0430 00024 (v02 _ASUS_)
[ 0.000000] ACPI: XSDT 00000000aaffee18 00074 (v01 _ASUS_ Notebook 06222004 MSFT 00010013)
[ 0.000000] ACPI: FACP 00000000aaf9bd98 000F4 (v04 _ASUS_ NoteBook 06222004 MSFT 00010013)
[ 0.000000] ACPI Warning: 32/64 FACS address mismatch in FADT - two FACS tables! (20110413/tbfadt-369)
[ 0.000000] ACPI Warning: 32/64X FACS address mismatch in FADT - 0xAAFE5E40/0x00000000AAFE5D40, using 32 (20110413/tbfadt-489)
[ 0.000000] ACPI: DSDT 00000000aaf7c018 0DC69 (v01 _ASUS_ NoteBook 00000000 INTL 20091112)
[ 0.000000] ACPI: FACS 00000000aafe5e40 00040
[ 0.000000] ACPI: APIC 00000000aaffdf18 000CC (v02 _ASUS_ NoteBook 06222004 MSFT 00010013)
[ 0.000000] ACPI: HPET 00000000aafe6d18 00038 (v01 _ASUS_ NoteBook 06222004 AMI. 00000003)
[ 0.000000] ACPI: ECDT 00000000aafe5b18 000C1 (v01 _ASUS_ NoteBook 06222004 AMI 00000000)
[ 0.000000] ACPI: MCFG 00000000aafe6c98 0003C (v01 _ASUS_ NoteBook 06222004 MSFT 00000097)
[ 0.000000] ACPI: SSDT 00000000aaf7b818 00799 (v01 PmRef Cpu0Ist 00003000 INTL 20091112)
[ 0.000000] ACPI: SSDT 00000000aaf7a018 00996 (v01 PmRef CpuPm 00003000 INTL 20091112)
[ 0.000000] ACPI: SLIC 00000000aaf9cc18 00176 (v01 _ASUS_ Notebook 06222004 ASUS 00000001)
[ 0.000000] ACPI: SSDT 00000000aaf5ea98 002EF (v01 SataRe SataTabl 00001000 INTL 20091112)
[ 0.000000] ACPI: ASF! 00000000aafe5a18 000A0 (v32 INTEL HCG568D 00000001 MSFT 000F4240)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000014fe00000
[ 0.000000] Initmem setup node 0 0000000000000000-000000014fe00000
[ 0.000000] NODE_DATA [000000014fdfb000 - 000000014fdfffff]
[ 0.000000] [ffffea0000000000-ffffea00049fffff] PMD -> [ffff88014b400000-ffff88014edfffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x0014fe00
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[9] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009e
[ 0.000000] 0: 0x00000100 -> 0x00020000
[ 0.000000] 0: 0x00020200 -> 0x00040000
[ 0.000000] 0: 0x00040200 -> 0x000aabcc
[ 0.000000] 0: 0x000aacdf -> 0x000aace1
[ 0.000000] 0: 0x000aacf4 -> 0x000aacf5
[ 0.000000] 0: 0x000aade8 -> 0x000aaf19
[ 0.000000] 0: 0x000aafe8 -> 0x000aaffd
[ 0.000000] 0: 0x00100000 -> 0x0014fe00
[ 0.000000] On node 0 totalpages: 1025699
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3921 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 680269 pages, LIFO batch:31
[ 0.000000] Normal zone: 4473 pages used for memmap
[ 0.000000] Normal zone: 322695 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x08] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x09] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x0a] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x0b] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x0c] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x0d] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x0e] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x10] lapic_id[0x0f] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] SMP: Allowing 16 CPUs, 12 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 0000000020000000 - 0000000020200000
[ 0.000000] PM: Registered nosave memory: 0000000040000000 - 0000000040200000
[ 0.000000] PM: Registered nosave memory: 00000000aabcc000 - 00000000aacdf000
[ 0.000000] PM: Registered nosave memory: 00000000aace1000 - 00000000aacf4000
[ 0.000000] PM: Registered nosave memory: 00000000aacf5000 - 00000000aade8000
[ 0.000000] PM: Registered nosave memory: 00000000aaf19000 - 00000000aafe8000
[ 0.000000] PM: Registered nosave memory: 00000000aaffd000 - 00000000ab000000
[ 0.000000] PM: Registered nosave memory: 00000000ab000000 - 00000000afa00000
[ 0.000000] PM: Registered nosave memory: 00000000afa00000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000e4000000
[ 0.000000] PM: Registered nosave memory: 00000000e4000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed10000
[ 0.000000] PM: Registered nosave memory: 00000000fed10000 - 00000000fed14000
[ 0.000000] PM: Registered nosave memory: 00000000fed14000 - 00000000fed18000
[ 0.000000] PM: Registered nosave memory: 00000000fed18000 - 00000000fed1a000
[ 0.000000] PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
[ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
[ 0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ff980000
[ 0.000000] PM: Registered nosave memory: 00000000ff980000 - 00000000ffc00000
[ 0.000000] PM: Registered nosave memory: 00000000ffc00000 - 00000000ffd80000
[ 0.000000] PM: Registered nosave memory: 00000000ffd80000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at afa00000 (gap: afa00000:30600000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:16 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff88014fa00000 s78464 r8192 d23936 u131072
[ 0.000000] pcpu-alloc: s78464 r8192 d23936 u131072 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1006885
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/disk/by-uuid/f3bdc9ce-59f4-42c8-98cd-bacdc7803d59 ro
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 3963540k/5502976k available (4064k kernel code, 1400180k absent, 139256k reserved, 3304k data, 712k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:2304
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 33554432 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.003333] Detected 2294.473 MHz processor.
[ 0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 4590.15 BogoMIPS (lpj=7648243)
[ 0.000007] pid_max: default: 32768 minimum: 301
[ 0.000118] Security Framework initialized
[ 0.000122] AppArmor: AppArmor disabled by boot time parameter
[ 0.000492] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.001691] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.002141] Mount-cache hash table entries: 256
[ 0.002461] Initializing cgroup subsys cpuacct
[ 0.002487] Initializing cgroup subsys memory
[ 0.002502] Initializing cgroup subsys devices
[ 0.002504] Initializing cgroup subsys freezer
[ 0.002505] Initializing cgroup subsys net_cls
[ 0.002507] Initializing cgroup subsys blkio
[ 0.002553] CPU: Physical Processor ID: 0
[ 0.002555] CPU: Processor Core ID: 0
[ 0.002560] mce: CPU supports 7 MCE banks
[ 0.002572] CPU0: Thermal monitoring enabled (TM1)
[ 0.002578] using mwait in idle threads.
[ 0.003714] ACPI: Core revision 20110413
[ 0.160380] ftrace: allocating 16144 entries in 64 pages
[ 0.167075] Switched APIC routing to physical flat.
[ 0.167426] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.200410] CPU0: Intel(R) Core(TM) i5-2410M CPU @ 2.30GHz stepping 07
[ 0.304675] Performance Events: PEBS fmt1+, SandyBridge events, Intel PMU driver.
[ 0.304681] ... version: 3
[ 0.304682] ... bit width: 48
[ 0.304683] ... generic registers: 4
[ 0.304685] ... value mask: 0000ffffffffffff
[ 0.304686] ... max period: 000000007fffffff
[ 0.304687] ... fixed-purpose events: 3
[ 0.304688] ... event mask: 000000070000000f
[ 0.324897] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.351341] Booting Node 0, Processors #1
[ 0.351348] smpboot cpu 1: start_ip = 99000
[ 0.464652] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.484623] #2
[ 0.484627] smpboot cpu 2: start_ip = 99000
[ 0.597913] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.617876] #3
[ 0.617880] smpboot cpu 3: start_ip = 99000
[ 0.741252] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.747769] Brought up 4 CPUs
[ 0.747775] Total of 4 processors activated (18364.91 BogoMIPS).
[ 0.750911] devtmpfs: initialized
[ 0.751676] PM: Registering ACPI NVS region at aaf19000 (847872 bytes)
[ 0.752391] print_constraints: dummy:
[ 0.752459] NET: Registered protocol family 16
[ 0.752545] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.752547] ACPI: bus type pci registered
[ 0.752684] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
[ 0.752687] PCI: MMCONFIG at [mem 0xe0000000-0xe3ffffff] reserved in E820
[ 0.768153] PCI: Using configuration type 1 for base access
[ 0.768569] bio: create slab <bio-0> at 0
[ 0.770460] ACPI: EC: EC description table is found, configuring boot EC
[ 0.770465] ACPI: EC: Look up EC in DSDT
[ 0.772328] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.784480] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.854764] ACPI: SSDT 00000000aadbc718 00694 (v01 PmRef Cpu0Cst 00003001 INTL 20091112)
[ 0.855208] ACPI: Dynamic OEM Table Load:
[ 0.855210] ACPI: SSDT (null) 00694 (v01 PmRef Cpu0Cst 00003001 INTL 20091112)
[ 0.864674] ACPI: SSDT 00000000aadbda98 00303 (v01 PmRef ApIst 00003000 INTL 20091112)
[ 0.865144] ACPI: Dynamic OEM Table Load:
[ 0.865146] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20091112)
[ 0.874544] ACPI: SSDT 00000000aadbbd98 00119 (v01 PmRef ApCst 00003000 INTL 20091112)
[ 0.874985] ACPI: Dynamic OEM Table Load:
[ 0.874987] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20091112)
[ 0.894586] ACPI: Interpreter enabled
[ 0.894589] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.894611] ACPI: Using IOAPIC for interrupt routing
[ 0.999159] ACPI: EC: GPE = 0x1b, I/O: command/status = 0x66, data = 0x62
[ 0.999351] ACPI: No dock devices found.
[ 0.999352] HEST: Table not found.
[ 0.999355] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.999558] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.999930] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.999932] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.999934] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.999936] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff]
[ 0.999938] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
[ 0.999940] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
[ 0.999942] pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff]
[ 0.999944] pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff]
[ 0.999946] pci_root PNP0A08:00: host bridge window [mem 0x000e4000-0x000e7fff]
[ 0.999948] pci_root PNP0A08:00: host bridge window [mem 0xafa00000-0xfeafffff]
[ 0.999950] pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfed44fff]
[ 0.999961] pci 0000:00:00.0: [8086:0104] type 0 class 0x000600
[ 0.999994] pci 0000:00:01.0: [8086:0101] type 1 class 0x000604
[ 1.000018] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 1.000021] pci 0000:00:01.0: PME# disabled
[ 1.000038] pci 0000:00:02.0: [8086:0116] type 0 class 0x000300
[ 1.000048] pci 0000:00:02.0: reg 10: [mem 0xdc400000-0xdc7fffff 64bit]
[ 1.000055] pci 0000:00:02.0: reg 18: [mem 0xb0000000-0xbfffffff 64bit pref]
[ 1.000059] pci 0000:00:02.0: reg 20: [io 0xe000-0xe03f]
[ 1.000109] pci 0000:00:16.0: [8086:1c3a] type 0 class 0x000780
[ 1.000132] pci 0000:00:16.0: reg 10: [mem 0xdf00b000-0xdf00b00f 64bit]
[ 1.000195] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 1.000200] pci 0000:00:16.0: PME# disabled
[ 1.000231] pci 0000:00:1a.0: [8086:1c2d] type 0 class 0x000c03
[ 1.000253] pci 0000:00:1a.0: reg 10: [mem 0xdf008000-0xdf0083ff]
[ 1.000326] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 1.000331] pci 0000:00:1a.0: PME# disabled
[ 1.000355] pci 0000:00:1b.0: [8086:1c20] type 0 class 0x000403
[ 1.000371] pci 0000:00:1b.0: reg 10: [mem 0xdf000000-0xdf003fff 64bit]
[ 1.000426] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 1.000430] pci 0000:00:1b.0: PME# disabled
[ 1.000450] pci 0000:00:1c.0: [8086:1c10] type 1 class 0x000604
[ 1.000513] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 1.000517] pci 0000:00:1c.0: PME# disabled
[ 1.000540] pci 0000:00:1c.1: [8086:1c12] type 1 class 0x000604
[ 1.000603] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 1.000607] pci 0000:00:1c.1: PME# disabled
[ 1.000632] pci 0000:00:1c.3: [8086:1c16] type 1 class 0x000604
[ 1.000695] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 1.000699] pci 0000:00:1c.3: PME# disabled
[ 1.000723] pci 0000:00:1c.5: [8086:1c1a] type 1 class 0x000604
[ 1.000785] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 1.000789] pci 0000:00:1c.5: PME# disabled
[ 1.000819] pci 0000:00:1d.0: [8086:1c26] type 0 class 0x000c03
[ 1.000841] pci 0000:00:1d.0: reg 10: [mem 0xdf007000-0xdf0073ff]
[ 1.000914] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 1.000919] pci 0000:00:1d.0: PME# disabled
[ 1.000944] pci 0000:00:1f.0: [8086:1c49] type 0 class 0x000601
[ 1.001066] pci 0000:00:1f.2: [8086:1c03] type 0 class 0x000106
[ 1.001085] pci 0000:00:1f.2: reg 10: [io 0xe0b0-0xe0b7]
[ 1.001094] pci 0000:00:1f.2: reg 14: [io 0xe0a0-0xe0a3]
[ 1.001102] pci 0000:00:1f.2: reg 18: [io 0xe090-0xe097]
[ 1.001111] pci 0000:00:1f.2: reg 1c: [io 0xe080-0xe083]
[ 1.001119] pci 0000:00:1f.2: reg 20: [io 0xe060-0xe07f]
[ 1.001128] pci 0000:00:1f.2: reg 24: [mem 0xdf006000-0xdf0067ff]
[ 1.001161] pci 0000:00:1f.2: PME# supported from D3hot
[ 1.001165] pci 0000:00:1f.2: PME# disabled
[ 1.001183] pci 0000:00:1f.3: [8086:1c22] type 0 class 0x000c05
[ 1.001199] pci 0000:00:1f.3: reg 10: [mem 0xdf005000-0xdf0050ff 64bit]
[ 1.001220] pci 0000:00:1f.3: reg 20: [io 0xe040-0xe05f]
[ 1.001276] pci 0000:01:00.0: [10de:0df4] type 0 class 0x000300
[ 1.001284] pci 0000:01:00.0: reg 10: [mem 0xdb000000-0xdbffffff]
[ 1.001292] pci 0000:01:00.0: reg 14: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 1.001301] pci 0000:01:00.0: reg 1c: [mem 0xd0000000-0xd1ffffff 64bit pref]
[ 1.001308] pci 0000:01:00.0: reg 24: [io 0xd000-0xd07f]
[ 1.001314] pci 0000:01:00.0: reg 30: [mem 0xdc000000-0xdc07ffff pref]
[ 1.001346] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 1.001348] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 1.001351] pci 0000:00:01.0: bridge window [mem 0xdb000000-0xdc0fffff]
[ 1.001354] pci 0000:00:01.0: bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[ 1.001399] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 1.001403] pci 0000:00:1c.0: bridge window [io 0xc000-0xcfff]
[ 1.001407] pci 0000:00:1c.0: bridge window [mem 0xde600000-0xdeffffff]
[ 1.001414] pci 0000:00:1c.0: bridge window [mem 0xd4200000-0xd4bfffff 64bit pref]
[ 1.001480] pci 0000:03:00.0: [168c:002b] type 0 class 0x000280
[ 1.001508] pci 0000:03:00.0: reg 10: [mem 0xddc00000-0xddc0ffff 64bit]
[ 1.001612] pci 0000:03:00.0: supports D1
[ 1.001614] pci 0000:03:00.0: PME# supported from D0 D1 D3hot D3cold
[ 1.001619] pci 0000:03:00.0: PME# disabled
[ 1.001657] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[ 1.001662] pci 0000:00:1c.1: bridge window [io 0xb000-0xbfff]
[ 1.001666] pci 0000:00:1c.1: bridge window [mem 0xddc00000-0xde5fffff]
[ 1.001672] pci 0000:00:1c.1: bridge window [mem 0xd3700000-0xd40fffff 64bit pref]
[ 1.001743] pci 0000:04:00.0: [1b73:1000] type 0 class 0x000c03
[ 1.001766] pci 0000:04:00.0: reg 10: [mem 0xdd200000-0xdd20ffff]
[ 1.001908] pci 0000:04:00.0: PME# supported from D0 D3hot
[ 1.001914] pci 0000:04:00.0: PME# disabled
[ 1.001944] pci 0000:00:1c.3: PCI bridge to [bus 04-04]
[ 1.001948] pci 0000:00:1c.3: bridge window [io 0xa000-0xafff]
[ 1.001952] pci 0000:00:1c.3: bridge window [mem 0xdd200000-0xddbfffff]
[ 1.001959] pci 0000:00:1c.3: bridge window [mem 0xd2c00000-0xd35fffff 64bit pref]
[ 1.002025] pci 0000:05:00.0: [1969:1083] type 0 class 0x000200
[ 1.002053] pci 0000:05:00.0: reg 10: [mem 0xdc800000-0xdc83ffff 64bit]
[ 1.002068] pci 0000:05:00.0: reg 18: [io 0x9000-0x907f]
[ 1.002166] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.002171] pci 0000:05:00.0: PME# disabled
[ 1.002210] pci 0000:00:1c.5: PCI bridge to [bus 05-05]
[ 1.002214] pci 0000:00:1c.5: bridge window [io 0x9000-0x9fff]
[ 1.002219] pci 0000:00:1c.5: bridge window [mem 0xdc800000-0xdd1fffff]
[ 1.002225] pci 0000:00:1c.5: bridge window [mem 0xd2100000-0xd2afffff 64bit pref]
[ 1.002249] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.002373] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 1.002402] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 1.002435] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 1.002467] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
[ 1.002510] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGR._PRT]
[ 1.002545] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 1.002548] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[ 1.002549] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 1.700980] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 1.701022] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 *3 4 5 6 10 11 12 14 15)
[ 1.701063] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 1.701104] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[ 1.701146] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 1.701186] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 1.701226] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 *5 6 10 11 12 14 15)
[ 1.701264] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 *4 5 6 10 11 12 14 15)
[ 1.701338] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 1.701345] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=none,locks=none
[ 1.701347] vgaarb: loaded
[ 1.701348] vgaarb: bridge control possible 0000:01:00.0
[ 1.701349] vgaarb: bridge control possible 0000:00:02.0
[ 1.701410] PCI: Using ACPI for IRQ routing
[ 1.702943] PCI: pci_cache_line_size set to 64 bytes
[ 1.703021] reserve RAM buffer: 000000000009e800 - 000000000009ffff
[ 1.703024] reserve RAM buffer: 00000000aabcc000 - 00000000abffffff
[ 1.703027] reserve RAM buffer: 00000000aace1000 - 00000000abffffff
[ 1.703029] reserve RAM buffer: 00000000aacf5000 - 00000000abffffff
[ 1.703031] reserve RAM buffer: 00000000aaf19000 - 00000000abffffff
[ 1.703033] reserve RAM buffer: 00000000aaffd000 - 00000000abffffff
[ 1.703035] reserve RAM buffer: 000000014fe00000 - 000000014fffffff
[ 1.703130] NetLabel: Initializing
[ 1.703131] NetLabel: domain hash size = 128
[ 1.703132] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.703144] NetLabel: unlabeled traffic allowed by default
[ 1.703158] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 1.703163] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 1.705180] Switching to clocksource hpet
[ 1.707228] Switched to NOHz mode on CPU #0
[ 1.707282] Switched to NOHz mode on CPU #1
[ 1.707289] Switched to NOHz mode on CPU #2
[ 1.707371] Switched to NOHz mode on CPU #3
[ 1.709995] pnp: PnP ACPI init
[ 1.710009] ACPI: bus type pnp registered
[ 1.710231] pnp 00:00: [bus 00-3e]
[ 1.710233] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 1.710235] pnp 00:00: [io 0x0cf8-0x0cff]
[ 1.710236] pnp 00:00: [io 0x0d00-0xffff window]
[ 1.710238] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 1.710240] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 1.710242] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 1.710243] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 1.710245] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 1.710247] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 1.710248] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 1.710250] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 1.710252] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 1.710253] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 1.710255] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 1.710257] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 1.710258] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 1.710260] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 1.710262] pnp 00:00: [mem 0xafa00000-0xfeafffff window]
[ 1.710264] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[ 1.710335] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 1.710347] pnp 00:01: [io 0x0000-0x001f]
[ 1.710349] pnp 00:01: [io 0x0081-0x0091]
[ 1.710350] pnp 00:01: [io 0x0093-0x009f]
[ 1.710351] pnp 00:01: [io 0x00c0-0x00df]
[ 1.710353] pnp 00:01: [dma 4]
[ 1.710371] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 1.710378] pnp 00:02: [mem 0xff000000-0xffffffff]
[ 1.710395] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[ 1.710466] pnp 00:03: [mem 0xfed00000-0xfed003ff]
[ 1.710484] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[ 1.710493] pnp 00:04: [io 0x00f0]
[ 1.710501] pnp 00:04: [irq 13]
[ 1.710519] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 1.710528] pnp 00:05: [io 0x002e-0x002f]
[ 1.710530] pnp 00:05: [io 0x004e-0x004f]
[ 1.710531] pnp 00:05: [io 0x0061]
[ 1.710533] pnp 00:05: [io 0x0063]
[ 1.710534] pnp 00:05: [io 0x0065]
[ 1.710535] pnp 00:05: [io 0x0067]
[ 1.710536] pnp 00:05: [io 0x0070]
[ 1.710538] pnp 00:05: [io 0x0080]
[ 1.710539] pnp 00:05: [io 0x0092]
[ 1.710542] pnp 00:05: [io 0x00b2-0x00b3]
[ 1.710544] pnp 00:05: [io 0x0680-0x069f]
[ 1.710545] pnp 00:05: [io 0x1000-0x100f]
[ 1.710546] pnp 00:05: [io 0xffff]
[ 1.710548] pnp 00:05: [io 0xffff]
[ 1.710549] pnp 00:05: [io 0x0400-0x0453]
[ 1.710550] pnp 00:05: [io 0x0458-0x047f]
[ 1.710552] pnp 00:05: [io 0x0500-0x057f]
[ 1.710553] pnp 00:05: [io 0x164e-0x164f]
[ 1.710595] system 00:05: [io 0x0680-0x069f] has been reserved
[ 1.710598] system 00:05: [io 0x1000-0x100f] has been reserved
[ 1.710600] system 00:05: [io 0xffff] has been reserved
[ 1.710601] system 00:05: [io 0xffff] has been reserved
[ 1.710603] system 00:05: [io 0x0400-0x0453] has been reserved
[ 1.710605] system 00:05: [io 0x0458-0x047f] has been reserved
[ 1.710607] system 00:05: [io 0x0500-0x057f] has been reserved
[ 1.710609] system 00:05: [io 0x164e-0x164f] has been reserved
[ 1.710612] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.710619] pnp 00:06: [io 0x0070-0x0077]
[ 1.710624] pnp 00:06: [irq 8]
[ 1.710642] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.710658] pnp 00:07: [io 0x0454-0x0457]
[ 1.710686] system 00:07: [io 0x0454-0x0457] has been reserved
[ 1.710689] system 00:07: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 1.710714] pnp 00:08: [io 0x0060]
[ 1.710716] pnp 00:08: [io 0x0064]
[ 1.710721] pnp 00:08: [irq 1]
[ 1.710741] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 1.710775] pnp 00:09: [irq 12]
[ 1.710798] pnp 00:09: Plug and Play ACPI device, IDs ETD0101 SYN0a00 SYN0002 PNP0f03 PNP0f13 PNP0f12 (active)
[ 1.758811] pnp 00:0a: [mem 0xfed1c000-0xfed1ffff]
[ 1.758813] pnp 00:0a: [mem 0xfed10000-0xfed17fff]
[ 1.758814] pnp 00:0a: [mem 0xfed18000-0xfed18fff]
[ 1.758816] pnp 00:0a: [mem 0xfed19000-0xfed19fff]
[ 1.758817] pnp 00:0a: [mem 0xe0000000-0xe3ffffff]
[ 1.758819] pnp 00:0a: [mem 0xfed20000-0xfed3ffff]
[ 1.758820] pnp 00:0a: [mem 0xfed90000-0xfed93fff]
[ 1.758822] pnp 00:0a: [mem 0xfed45000-0xfed8ffff]
[ 1.758824] pnp 00:0a: [mem 0xff000000-0xffffffff]
[ 1.758825] pnp 00:0a: [mem 0xfee00000-0xfeefffff]
[ 1.758827] pnp 00:0a: [mem 0xafa00000-0xafa00fff]
[ 1.758884] system 00:0a: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 1.758887] system 00:0a: [mem 0xfed10000-0xfed17fff] could not be reserved
[ 1.758889] system 00:0a: [mem 0xfed18000-0xfed18fff] has been reserved
[ 1.758891] system 00:0a: [mem 0xfed19000-0xfed19fff] has been reserved
[ 1.758893] system 00:0a: [mem 0xe0000000-0xe3ffffff] has been reserved
[ 1.758895] system 00:0a: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 1.758897] system 00:0a: [mem 0xfed90000-0xfed93fff] has been reserved
[ 1.758900] system 00:0a: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 1.758902] system 00:0a: [mem 0xff000000-0xffffffff] could not be reserved
[ 1.758904] system 00:0a: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 1.758906] system 00:0a: [mem 0xafa00000-0xafa00fff] has been reserved
[ 1.758909] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.758934] pnp 00:0b: [mem 0xafa00000-0xafa00fff]
[ 1.758981] system 00:0b: [mem 0xafa00000-0xafa00fff] has been reserved
[ 1.758984] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.759078] pnp 00:0c: [mem 0x20000000-0x201fffff]
[ 1.759080] pnp 00:0c: [mem 0x40000000-0x401fffff]
[ 1.759131] system 00:0c: [mem 0x20000000-0x201fffff] has been reserved
[ 1.759133] system 00:0c: [mem 0x40000000-0x401fffff] has been reserved
[ 1.759136] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 1.759147] pnp: PnP ACPI: found 13 devices
[ 1.759148] ACPI: ACPI bus type pnp unregistered
[ 1.764848] PCI: max bus depth: 1 pci_try_num: 2
[ 1.764884] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 1.764886] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 1.764889] pci 0000:00:01.0: bridge window [mem 0xdb000000-0xdc0fffff]
[ 1.764892] pci 0000:00:01.0: bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[ 1.764896] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 1.764899] pci 0000:00:1c.0: bridge window [io 0xc000-0xcfff]
[ 1.764905] pci 0000:00:1c.0: bridge window [mem 0xde600000-0xdeffffff]
[ 1.764909] pci 0000:00:1c.0: bridge window [mem 0xd4200000-0xd4bfffff 64bit pref]
[ 1.764916] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[ 1.764919] pci 0000:00:1c.1: bridge window [io 0xb000-0xbfff]
[ 1.764925] pci 0000:00:1c.1: bridge window [mem 0xddc00000-0xde5fffff]
[ 1.764929] pci 0000:00:1c.1: bridge window [mem 0xd3700000-0xd40fffff 64bit pref]
[ 1.764936] pci 0000:00:1c.3: PCI bridge to [bus 04-04]
[ 1.764939] pci 0000:00:1c.3: bridge window [io 0xa000-0xafff]
[ 1.764944] pci 0000:00:1c.3: bridge window [mem 0xdd200000-0xddbfffff]
[ 1.764949] pci 0000:00:1c.3: bridge window [mem 0xd2c00000-0xd35fffff 64bit pref]
[ 1.764956] pci 0000:00:1c.5: PCI bridge to [bus 05-05]
[ 1.764959] pci 0000:00:1c.5: bridge window [io 0x9000-0x9fff]
[ 1.764964] pci 0000:00:1c.5: bridge window [mem 0xdc800000-0xdd1fffff]
[ 1.764969] pci 0000:00:1c.5: bridge window [mem 0xd2100000-0xd2afffff 64bit pref]
[ 1.764983] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.764986] pci 0000:00:01.0: setting latency timer to 64
[ 1.764993] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.764997] pci 0000:00:1c.0: setting latency timer to 64
[ 1.765005] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.765010] pci 0000:00:1c.1: setting latency timer to 64
[ 1.765018] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 1.765022] pci 0000:00:1c.3: setting latency timer to 64
[ 1.765028] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.765033] pci 0000:00:1c.5: setting latency timer to 64
[ 1.765037] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 1.765039] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 1.765041] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.765042] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
[ 1.765044] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
[ 1.765046] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
[ 1.765048] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff]
[ 1.765050] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff]
[ 1.765051] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff]
[ 1.765053] pci_bus 0000:00: resource 13 [mem 0xafa00000-0xfeafffff]
[ 1.765055] pci_bus 0000:00: resource 14 [mem 0xfed40000-0xfed44fff]
[ 1.765057] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 1.765059] pci_bus 0000:01: resource 1 [mem 0xdb000000-0xdc0fffff]
[ 1.765061] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xd1ffffff 64bit pref]
[ 1.765063] pci_bus 0000:02: resource 0 [io 0xc000-0xcfff]
[ 1.765064] pci_bus 0000:02: resource 1 [mem 0xde600000-0xdeffffff]
[ 1.765066] pci_bus 0000:02: resource 2 [mem 0xd4200000-0xd4bfffff 64bit pref]
[ 1.765068] pci_bus 0000:03: resource 0 [io 0xb000-0xbfff]
[ 1.765070] pci_bus 0000:03: resource 1 [mem 0xddc00000-0xde5fffff]
[ 1.765072] pci_bus 0000:03: resource 2 [mem 0xd3700000-0xd40fffff 64bit pref]
[ 1.765074] pci_bus 0000:04: resource 0 [io 0xa000-0xafff]
[ 1.765076] pci_bus 0000:04: resource 1 [mem 0xdd200000-0xddbfffff]
[ 1.765078] pci_bus 0000:04: resource 2 [mem 0xd2c00000-0xd35fffff 64bit pref]
[ 1.765080] pci_bus 0000:05: resource 0 [io 0x9000-0x9fff]
[ 1.765081] pci_bus 0000:05: resource 1 [mem 0xdc800000-0xdd1fffff]
[ 1.765083] pci_bus 0000:05: resource 2 [mem 0xd2100000-0xd2afffff 64bit pref]
[ 1.765138] NET: Registered protocol family 2
[ 1.765319] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.766220] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 1.767965] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.768183] TCP: Hash tables configured (established 524288 bind 65536)
[ 1.768185] TCP reno registered
[ 1.768194] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 1.768216] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 1.768449] NET: Registered protocol family 1
[ 1.768464] pci 0000:00:02.0: Boot video device
[ 2.015314] PCI: CLS 64 bytes, default 64
[ 2.015352] Unpacking initramfs...
[ 2.047361] Freeing initrd memory: 2368k freed
[ 2.047653] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 2.047657] Placing 64MB software IO TLB between ffff8800a6bcc000 - ffff8800aabcc000
[ 2.047658] software IO TLB at phys 0xa6bcc000 - 0xaabcc000
[ 2.048060] audit: initializing netlink socket (disabled)
[ 2.048068] type=2000 audit(1313603670.739:1): initialized
[ 2.054235] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 2.067195] VFS: Disk quotas dquot_6.5.2
[ 2.067311] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.067454] msgmni has been set to 7745
[ 2.067640] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.067672] io scheduler noop registered
[ 2.067674] io scheduler deadline registered
[ 2.067711] io scheduler cfq registered (default)
[ 2.067791] pcieport 0000:00:01.0: setting latency timer to 64
[ 2.067814] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 2.068084] intel_idle: MWAIT substates: 0x21120
[ 2.068086] intel_idle: v0.4 model 0x2A
[ 2.068087] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 2.068117] ERST: Table is not found!
[ 2.068163] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.268759] Linux agpgart interface v0.103
[ 2.268839] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 2.270529] i8042: Detected active multiplexing controller, rev 1.1
[ 2.271297] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.271322] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 2.271339] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 2.271357] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 2.271374] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 2.271436] mousedev: PS/2 mouse device common for all mice
[ 2.271488] rtc_cmos 00:06: RTC can wake from S4
[ 2.271585] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 2.271612] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[ 2.271729] cpuidle: using governor ladder
[ 2.271883] cpuidle: using governor menu
[ 2.272040] TCP cubic registered
[ 2.272042] NET: Registered protocol family 17
[ 2.272048] Registering the dns_resolver key type
[ 2.272116] PM: Hibernation image not present or could not be loaded.
[ 2.272120] registered taskstats version 1
[ 2.278319] rtc_cmos 00:06: setting system clock to 2011-08-17 17:54:31 UTC (1313603671)
[ 2.278398] Initializing network drop monitor service
[ 2.279674] Freeing unused kernel memory: 712k freed
[ 2.279759] Write protecting the kernel read-only data: 6144k
[ 2.279988] Freeing unused kernel memory: 12k freed
[ 2.282266] Freeing unused kernel memory: 776k freed
[ 2.291723] udevd[55]: starting version 173
[ 2.304579] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 2.339771] usbcore: registered new interface driver usbfs
[ 2.339795] usbcore: registered new interface driver hub
[ 2.341676] usbcore: registered new device driver usb
[ 2.342076] SCSI subsystem initialized
[ 2.346410] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.346435] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.346439] libata version 3.00 loaded.
[ 2.346468] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.346474] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 2.346533] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 2.346567] ehci_hcd 0000:00:1a.0: debug port 2
[ 2.350464] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[ 2.350482] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xdf008000
[ 2.361641] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 2.361880] hub 1-0:1.0: USB hub found
[ 2.361885] hub 1-0:1.0: 2 ports detected
[ 2.361969] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.362000] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.362005] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 2.362014] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.362042] ehci_hcd 0000:00:1d.0: debug port 2
[ 2.363294] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 2.363343] xhci_hcd 0000:04:00.0: setting latency timer to 64
[ 2.363348] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 2.363358] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3
[ 2.365933] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[ 2.365956] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xdf007000
[ 2.378294] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 2.378444] hub 2-0:1.0: USB hub found
[ 2.378448] hub 2-0:1.0: 2 ports detected
[ 2.378553] ahci 0000:00:1f.2: version 3.0
[ 2.378566] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.378706] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[ 2.378982] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x5 impl SATA mode
[ 2.378987] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst
[ 2.378993] ahci 0000:00:1f.2: setting latency timer to 64
[ 2.385587] scsi0 : ahci
[ 2.385700] scsi1 : ahci
[ 2.385786] scsi2 : ahci
[ 2.385871] scsi3 : ahci
[ 2.385959] scsi4 : ahci
[ 2.386043] scsi5 : ahci
[ 2.386296] ata1: SATA max UDMA/133 abar m2048@0xdf006000 port 0xdf006100 irq 41
[ 2.386298] ata2: DUMMY
[ 2.386302] ata3: SATA max UDMA/133 abar m2048@0xdf006000 port 0xdf006200 irq 41
[ 2.386303] ata4: DUMMY
[ 2.386304] ata5: DUMMY
[ 2.386305] ata6: DUMMY
[ 2.499498] xhci_hcd 0000:04:00.0: irq 19, io mem 0xdd200000
[ 2.499623] xHCI xhci_add_endpoint called for root hub
[ 2.499625] xHCI xhci_check_bandwidth called for root hub
[ 2.499650] hub 3-0:1.0: USB hub found
[ 2.499655] hub 3-0:1.0: 1 port detected
[ 2.499701] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 2.499707] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 4
[ 2.499773] xHCI xhci_add_endpoint called for root hub
[ 2.499775] xHCI xhci_check_bandwidth called for root hub
[ 2.499793] hub 4-0:1.0: USB hub found
[ 2.499799] hub 4-0:1.0: 1 port detected
[ 2.668242] usb 1-1: new high speed USB device number 2 using ehci_hcd
[ 2.704896] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.704948] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.706090] ata1.00: ACPI cmd ef/90:06:00:00:00:00 (SET FEATURES) succeeded
[ 2.706102] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 2.706110] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 2.706942] ata1.00: ATA-8: ST9500423AS, 0002SDM1, max UDMA/133
[ 2.706951] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 2.708085] ata1.00: ACPI cmd ef/90:06:00:00:00:00 (SET FEATURES) succeeded
[ 2.708096] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 2.708128] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 2.708250] ata3.00: ACPI cmd ef/90:06:00:00:00:00 (SET FEATURES) succeeded
[ 2.708253] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 2.708256] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 2.708955] ata1.00: configured for UDMA/133
[ 2.709184] scsi 0:0:0:0: Direct-Access ATA ST9500423AS 0002 PQ: 0 ANSI: 5
[ 2.710001] ata3.00: ATAPI: MATSHITADVD-RAM UJ8A2ASW, 1.00, max UDMA/100
[ 2.713629] ata3.00: ACPI cmd ef/90:06:00:00:00:00 (SET FEATURES) succeeded
[ 2.713640] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 2.713648] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 2.715460] ata3.00: configured for UDMA/100
[ 2.721215] scsi 2:0:0:0: CD-ROM MATSHITA DVD-RAM UJ8A2ASW 1.00 PQ: 0 ANSI: 5
[ 2.726730] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 2.726735] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 2.726769] sd 0:0:0:0: [sda] Write Protect is off
[ 2.726772] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.726796] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.730604] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.730613] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.730825] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 2.744374] sda: sda1 sda2 sda3 sda4
[ 2.744800] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.792361] hub 1-1:1.0: USB hub found
[ 2.792438] hub 1-1:1.0: 6 ports detected
[ 2.898039] usb 2-1: new high speed USB device number 2 using ehci_hcd
[ 3.022001] hub 2-1:1.0: USB hub found
[ 3.022058] hub 2-1:1.0: 6 ports detected
[ 3.047955] Refined TSC clocksource calibration: 2294.788 MHz.
[ 3.047965] Switching to clocksource tsc
[ 3.088035] usb 1-1.1: new full speed USB device number 3 using ehci_hcd
[ 3.154812] usb 1-1.1: device descriptor read/64, error -32
[ 3.236960] PM: Marking nosave pages: 000000000009e000 - 0000000000100000
[ 3.236965] PM: Marking nosave pages: 0000000020000000 - 0000000020200000
[ 3.236973] PM: Marking nosave pages: 0000000040000000 - 0000000040200000
[ 3.236982] PM: Marking nosave pages: 00000000aabcc000 - 00000000aacdf000
[ 3.236987] PM: Marking nosave pages: 00000000aace1000 - 00000000aacf4000
[ 3.236989] PM: Marking nosave pages: 00000000aacf5000 - 00000000aade8000
[ 3.236994] PM: Marking nosave pages: 00000000aaf19000 - 00000000aafe8000
[ 3.236998] PM: Marking nosave pages: 00000000aaffd000 - 0000000100000000
[ 3.238148] PM: Basic memory bitmaps created
[ 3.256065] PM: Basic memory bitmaps freed
[ 3.281008] EXT3-fs: barriers not enabled
[ 3.293754] kjournald starting. Commit interval 5 seconds
[ 3.293785] EXT3-fs (sda3): mounted filesystem with ordered data mode
[ 3.408060] usb 1-1.2: new high speed USB device number 4 using ehci_hcd
[ 4.495259] udevd[256]: starting version 173
[ 4.578020] ACPI: acpi_idle yielding to intel_idle
[ 4.627803] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[ 4.627906] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 4.628446] ACPI: AC Adapter [AC0] (on-line)
[ 4.629029] ACPI: Lid Switch [LID]
[ 4.629597] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[ 4.629603] ACPI: Sleep Button [SLPB]
[ 4.629654] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 4.629658] ACPI: Power Button [PWRF]
[ 4.662098] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 4.662105] ACPI: Battery Slot [BAT0] (battery present)
[ 4.670264] thermal LNXTHERM:00: registered as thermal_zone0
[ 4.670270] ACPI: Thermal Zone [TZ00] (58 C)
[ 4.699183] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.699224] sr 2:0:0:0: Attached scsi generic sg1 type 5
[ 4.735002] wmi: Mapper loaded
[ 4.816453] cfg80211: Calling CRDA to update world regulatory domain
[ 4.837422] Linux media interface: v0.10
[ 4.865736] Linux video capture interface: v2.00
[ 4.900747] uvcvideo: Found UVC 1.00 device ASUS USB2.0 WebCam (058f:a014)
[ 4.903658] input: ASUS USB2.0 WebCam as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input4
[ 4.903716] usbcore: registered new interface driver uvcvideo
[ 4.903718] USB Video Class driver (v1.1.0)
[ 4.911301] ath9k 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 4.911316] ath9k 0000:03:00.0: setting latency timer to 64
[ 4.919790] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 4.919846] HDA Intel 0000:00:1b.0: irq 42 for MSI/MSI-X
[ 4.919869] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 4.927271] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 4.935157] asus_wmi: ASUS WMI generic driver loaded
[ 4.941164] mei: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.943980] asus_wmi: Initialization: 0x1
[ 4.944133] asus_wmi: SFUN value: 0x1a0af7
[ 4.945199] input: Asus WMI hotkeys as /devices/platform/asus-nb-wmi/input/input5
[ 4.956683] asus_wmi: Backlight controlled by ACPI video driver
[ 4.956752] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 4.960798] ath: EEPROM regdomain: 0x60
[ 4.960800] ath: EEPROM indicates we should expect a direct regpair map
[ 4.960802] ath: Country alpha2 being used: 00
[ 4.960803] ath: Regpair used: 0x60
[ 4.974078] Bluetooth: Core ver 2.16
[ 4.974096] NET: Registered protocol family 31
[ 4.974097] Bluetooth: HCI device and connection manager initialized
[ 4.974098] Bluetooth: HCI socket layer initialized
[ 4.974099] Bluetooth: L2CAP socket layer initialized
[ 4.974302] Bluetooth: SCO socket layer initialized
[ 4.984561] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 4.984762] Registered led device: ath9k-phy0
[ 4.984768] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xffffc90005360000, irq=17
[ 4.999019] iTCO_vendor_support: vendor-support=0
[ 5.000922] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
[ 5.000993] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[ 5.001120] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 5.013874] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 5.014040] usbcore: registered new interface driver btusb
[ 5.026354] atl1c 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 5.026365] atl1c 0000:05:00.0: setting latency timer to 64
[ 5.140660] atl1c 0000:05:00.0: version 1.0.1.0-NAPI
[ 5.493359] hda_codec: ALC269VB: BIOS auto-probing.
[ 5.525717] HDMI status: Pin=6 Presence_Detect=0 ELD_Valid=0
[ 5.528101] input: HDA Intel PCH HDMI/DP as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 5.528163] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 5.528222] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 5.528376] mei 0000:00:16.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 5.528381] mei 0000:00:16.0: setting latency timer to 64
[ 5.535903] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 5.536243] agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
[ 5.536438] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[ 5.537725] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
[ 5.537829] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xb0000000
[ 5.566314] [drm] Initialized drm 1.1.0 20060810
[ 5.578198] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 5.578202] i915 0000:00:02.0: setting latency timer to 64
[ 5.616676] input: PS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio4/input/input10
[ 5.640873] i915 0000:00:02.0: irq 43 for MSI/MSI-X
[ 5.640878] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 5.640879] [drm] Driver supports precise vblank timestamp query.
[ 5.640934] [drm:intel_dsm_platform_mux_info] *ERROR* MUX INFO call failed
[ 5.641035] [drm:intel_dsm_platform_mux_info] *ERROR* MUX INFO call failed
[ 5.641105] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 5.641106] vgaarb: transferring owner from PCI:0000:00:02.0 to PCI:0000:01:00.0
[ 5.817467] fbcon: inteldrmfb (fb0) is primary device
[ 5.981060] Console: switching to colour frame buffer device 170x48
[ 5.982871] fb0: inteldrmfb frame buffer device
[ 5.982872] drm: registered panic notifier
[ 6.010757] ACPI Warning: _BQC returned an invalid level (20110413/video-473)
[ 6.011024] acpi device:4e: registered as cooling_device4
[ 6.011185] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input11
[ 6.011212] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 6.011736] ACPI Warning: _BQC returned an invalid level (20110413/video-473)
[ 6.011930] acpi device:59: registered as cooling_device5
[ 6.012005] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:55/LNXVIDEO:01/input/input12
[ 6.012073] ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)
[ 6.012134] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 6.806806] EXT3-fs (sda3): using internal journal
[ 7.032629] EXT3-fs: barriers not enabled
[ 7.033131] kjournald starting. Commit interval 5 seconds
[ 7.033638] EXT3-fs (sda4): using internal journal
[ 7.033650] EXT3-fs (sda4): mounted filesystem with ordered data mode
[ 7.136750] Adding 2097140k swap on /dev/sda2. Priority:-1 extents:1 across:2097140k
[ 8.830153] NET: Registered protocol family 10
[ 9.400174] ehci_hcd 0000:00:1d.0: PCI INT A disabled
[ 9.400249] ehci_hcd 0000:00:1d.0: PME# enabled
[ 9.413816] xhci_hcd 0000:04:00.0: PCI INT A disabled
[ 9.413916] xhci_hcd 0000:04:00.0: PME# enabled
[ 9.644602] ehci_hcd 0000:00:1d.0: BAR 0: set to [mem 0xdf007000-0xdf0073ff] (PCI address [0xdf007000-0xdf0073ff])
[ 9.644638] ehci_hcd 0000:00:1d.0: restoring config space at offset 0xf (was 0x100, writing 0x104)
[ 9.644679] ehci_hcd 0000:00:1d.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002)
[ 9.644796] ehci_hcd 0000:00:1d.0: PME# disabled
[ 9.644816] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 9.644828] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 9.754551] xhci_hcd 0000:04:00.0: BAR 0: set to [mem 0xdd200000-0xdd20ffff] (PCI address [0xdd200000-0xdd20ffff])
[ 9.754699] xhci_hcd 0000:04:00.0: PME# disabled
[ 9.754721] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 9.754736] xhci_hcd 0000:04:00.0: setting latency timer to 64
[ 9.754760] usb usb3: root hub lost power or was reset
[ 9.754764] usb usb4: root hub lost power or was reset
[ 167.112308] atl1c 0000:05:00.0: irq 44 for MSI/MSI-X
[ 167.112437] atl1c 0000:05:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 177.751730] eth0: no IPv6 routers present
$ dmesg | grep -i input
[ 2.304579] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 4.627803] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[ 4.629597] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[ 4.629654] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 4.903658] input: ASUS USB2.0 WebCam as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input4
[ 4.945199] input: Asus WMI hotkeys as /devices/platform/asus-nb-wmi/input/input5
[ 4.956752] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 5.528101] input: HDA Intel PCH HDMI/DP as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 5.528163] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 5.528222] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 5.616676] input: PS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio4/input/input10
[ 6.011185] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input11
[ 6.012005] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:55/LNXVIDEO:01/input/input12
$ cat /sys/class/input/mouse0/device/uevent
PRODUCT=11/2/1/63
NAME="PS/2 Logitech Wheel Mouse"
PHYS="isa0060/serio4/input0"
PROP=0
EV=7
KEY=70000 0 0 0 0
REL=103
MODALIAS=input:b0011v0002p0001e0063-e0,1,2,k110,111,112,r0,1,8,amlsfw
$ cat /var/log/Xorg.0.log
[ 232.348]
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
[ 232.349]
X.Org X Server 1.10.3.901 (1.10.4 RC 1)
Release Date: 2011-07-29
[ 232.349] X Protocol Version 11, Revision 0
[ 232.349] Build Operating System: Linux 3.0.0-ARCH x86_64
[ 232.349] Current Operating System: Linux asdfg 3.0-ARCH #1 SMP PREEMPT Tue Aug 16 08:44:20 CEST 2011 x86_64
[ 232.350] Kernel command line: root=/dev/disk/by-uuid/f3bdc9ce-59f4-42c8-98cd-bacdc7803d59 ro
[ 232.350] Build Date: 08 August 2011 08:24:13AM
[ 232.350]
[ 232.350] Current version of pixman: 0.22.2
[ 232.350] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 232.350] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 232.351] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Aug 17 19:58:21 2011
[ 232.397] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 232.406] (==) No Layout section. Using the first Screen section.
[ 232.406] (==) No screen section available. Using defaults.
[ 232.406] (**) |-->Screen "Default Screen Section" (0)
[ 232.406] (**) | |-->Monitor "<default monitor>"
[ 232.406] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 232.407] (==) Automatically adding devices
[ 232.407] (==) Automatically enabling devices
[ 232.464] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 232.464] Entry deleted from font path.
[ 232.464] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 232.464] Entry deleted from font path.
[ 232.464] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 232.465] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 232.465] Entry deleted from font path.
[ 232.465] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 232.465] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/OTF/
[ 232.465] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 232.465] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 232.465] (II) Loader magic: 0x7d3620
[ 232.465] (II) Module ABI versions:
[ 232.465] X.Org ANSI C Emulation: 0.4
[ 232.465] X.Org Video Driver: 10.0
[ 232.465] X.Org XInput driver : 12.2
[ 232.465] X.Org Server Extension : 5.0
[ 232.466] (--) PCI:*(0:0:2:0) 8086:0116:1043:1662 rev 9, Mem @ 0xdc400000/4194304, 0xb0000000/268435456, I/O @ 0x0000e000/64
[ 232.466] (--) PCI: (0:1:0:0) 10de:0df4:1043:1662 rev 161, Mem @ 0xdb000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x0000d000/128, BIOS @ 0x????????/524288
[ 232.466] (II) Open ACPI successful (/var/run/acpid.socket)
[ 232.466] (II) LoadModule: "extmod"
[ 232.498] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 232.500] (II) Module extmod: vendor="X.Org Foundation"
[ 232.500] compiled for 1.10.3.901, module version = 1.0.0
[ 232.500] Module class: X.Org Server Extension
[ 232.500] ABI class: X.Org Server Extension, version 5.0
[ 232.500] (II) Loading extension MIT-SCREEN-SAVER
[ 232.500] (II) Loading extension XFree86-VidModeExtension
[ 232.500] (II) Loading extension XFree86-DGA
[ 232.500] (II) Loading extension DPMS
[ 232.500] (II) Loading extension XVideo
[ 232.500] (II) Loading extension XVideo-MotionCompensation
[ 232.500] (II) Loading extension X-Resource
[ 232.500] (II) LoadModule: "dbe"
[ 232.500] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 232.501] (II) Module dbe: vendor="X.Org Foundation"
[ 232.501] compiled for 1.10.3.901, module version = 1.0.0
[ 232.501] Module class: X.Org Server Extension
[ 232.501] ABI class: X.Org Server Extension, version 5.0
[ 232.501] (II) Loading extension DOUBLE-BUFFER
[ 232.501] (II) LoadModule: "glx"
[ 232.502] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 232.517] (II) Module glx: vendor="X.Org Foundation"
[ 232.517] compiled for 1.10.3.901, module version = 1.0.0
[ 232.517] ABI class: X.Org Server Extension, version 5.0
[ 232.517] (==) AIGLX enabled
[ 232.517] (II) Loading extension GLX
[ 232.517] (II) LoadModule: "record"
[ 232.517] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 232.518] (II) Module record: vendor="X.Org Foundation"
[ 232.518] compiled for 1.10.3.901, module version = 1.13.0
[ 232.518] Module class: X.Org Server Extension
[ 232.518] ABI class: X.Org Server Extension, version 5.0
[ 232.518] (II) Loading extension RECORD
[ 232.518] (II) LoadModule: "dri"
[ 232.519] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 232.536] (II) Module dri: vendor="X.Org Foundation"
[ 232.536] compiled for 1.10.3.901, module version = 1.0.0
[ 232Interestingly enough, the same thing happens in Windows on my U46E - the Synaptics driver recognizes the touchpad only as a PS/2 mouse and two-finger scroll won't work.
Edit: The elantech module you posted fixes the problem on the U46E, too. Thanks! Now to fix it for Windows...
Last edited by kalinatek (2011-08-29 20:13:07) -
Synaptic touchpad stops working now and then on ProBook 6450b
The touchpad on my ProBook 6450b stops working every now and then. It just freezes, no error message or anything. It always works again after I reboot. It also starts working immediately if I go to the Task Manager and kill SynTPEnh.exe and then restart SynTPEnh.exe via Explorer (C:\Program Files\Synaptic\SynTP\SynTPEnh.exe). I have had this machine for 9 months, and these problems started only a couple of weeks ago. There are no error messages, and Device Manager says the device is working properly even when the touchpad is frozen. Sometimes I can go days without having a freeze, sometimes multiple freezes within minutes. Also, it happens during different activities - web browsing, watching movies, etc.
I'm not sure, but I might have enabled the WiFi-card in the BIOS prior to having these problems. However, as I currently need wireless, disabling it again is not an option.
I tried updating the BIOS, but the installation program wouldn't detect my SanDisk Cruzer USB stick, so I couldn't make a backup and decided to abort the procedure. I also tried installing another version of the Synaptic driver (can't remember the version, but it said "Evaluation Copy" on the Synaptic device in the Control Panel). It worked for a couple of days, then I got the old freeze again.
My setup:
HP ProBook 6450b
Windows 7 Professional 32-bit
Synaptic driver version 15.0.24As a "quick'n'dirty" solution, I figured out how to automate this process. Simply create a new textfile called "Restart Synaptics.bat" and enter the following into it:
taskkill /IM SynTPEnh.exe /F
"C:\Program Files\Synaptics\SynTP\SynTPEnh.exe"
This will kill the SynTPEnh.exe process and then restart it. Now put a shortcut to your batch file in the Start Menu for easy access. -
Elantech Touchpad Detected As PS/2 Elantech Mouse (Dell Vostro 3560)
Dear community,
I am facing troubles with my Dell Vostro 3560's Elantech Touchpad. It gets detected as PS/2 Elantech mouse.
[acs@einherij ~]$ xinput list
⎡ Virtual core pointer id=2 [master pointer (3)]
⎜ ↳ Virtual core XTEST pointer id=4 [slave pointer (2)]
⎜ ↳ PS/2 Elantech Mouse id=12 [slave pointer (2)]
⎣ Virtual core keyboard id=3 [master keyboard (2)]
↳ Virtual core XTEST keyboard id=5 [slave keyboard (3)]
↳ Power Button id=6 [slave keyboard (3)]
↳ Video Bus id=7 [slave keyboard (3)]
↳ Power Button id=8 [slave keyboard (3)]
↳ Sleep Button id=9 [slave keyboard (3)]
↳ Laptop_Integrated_Webcam_E4HD id=10 [slave keyboard (3)]
↳ AT Translated Set 2 keyboard id=11 [slave keyboard (3)]
↳ Dell WMI hotkeys id=13 [slave keyboard (3)]
Testwise. I installed from AUR the "psmouse-elantech" package (as mentioned in the Touchpad Synaptics article). After reboot, no effect at all, xinput gives the same output.
Can somebody point me in the correct direction please?
--- snip /var/log/Xorg.0.log ---
[ 11.978] (II) config/udev: Adding input device PS/2 Elantech Mouse (/dev/input/event11)
[ 11.978] (**) PS/2 Elantech Mouse: Applying InputClass "evdev pointer catchall"
[ 11.978] (II) Using input driver 'evdev' for 'PS/2 Elantech Mouse'
[ 11.978] (**) PS/2 Elantech Mouse: always reports core events
[ 11.978] (**) evdev: PS/2 Elantech Mouse: Device: "/dev/input/event11"
[ 11.978] (--) evdev: PS/2 Elantech Mouse: Vendor 0x2 Product 0x1
[ 11.978] (--) evdev: PS/2 Elantech Mouse: Found 3 mouse buttons
[ 11.978] (--) evdev: PS/2 Elantech Mouse: Found relative axes
[ 11.978] (--) evdev: PS/2 Elantech Mouse: Found x and y relative axes
[ 11.978] (II) evdev: PS/2 Elantech Mouse: Configuring as mouse
[ 11.978] (**) evdev: PS/2 Elantech Mouse: YAxisMapping: buttons 4 and 5
[ 11.978] (**) evdev: PS/2 Elantech Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 11.978] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input11/event11"
[ 11.978] (II) XINPUT: Adding extended input device "PS/2 Elantech Mouse" (type: MOUSE, id 12)
[ 11.978] (II) evdev: PS/2 Elantech Mouse: initialized for relative axes.
--- snap ---
Last edited by sonnyka (2012-08-07 16:58:44)also see: https://bbs.archlinux.org/viewtopic.php?id=117109
-
G6 2006-tx: synaptic touchpad is not listed in mice and other pointind device (device manager)
hi,
i just upgrade my window 7 home to window 8 pro... and i am now unable to scroll through my touch pad.
before upgrading, my touch pad was working properly, but now its only work as mouse to click items.
neither it scrolling nor zooming using two fingers.
plz tell me, should i have to reinstall my synaptic touch pad drivers?
plz provide me link
model: hp pavillion g6 2006-txHello,
I see that you're having an issue with the touchpad not showing up in the device manager. This could be because you're missing the drivers for the touchpad in Win8.
Here are the drivers you will need to install. Also, go ahead and follow this document if you're having any other issues with the touchpad.
This document has several sections that will help you will every possible issue.
If you have any other questions let me know. Please let me know the outcome to this also.
THX -
Synaptic touchpad not reconizing
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input1
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
[ 528.971] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event6)
[ 528.971] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 528.971] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 528.971] (II) LoadModule: "synaptics"
[ 528.971] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 528.971] (II) Module synaptics: vendor="X.Org Foundation"
[ 528.971] compiled for 1.8.0.902, module version = 1.2.2
[ 528.971] Module class: X.Org XInput Driver
[ 528.971] ABI class: X.Org XInput driver, version 9.0
[ 528.971] (II) Synaptics touchpad driver version 1.2.2
[ 528.971] (**) Option "Device" "/dev/input/event6"
[ 528.971] (II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
[ 528.971] (II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
[ 528.971] (II) SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[ 528.971] (II) SynPS/2 Synaptics TouchPad: finger width range 0 - 0
[ 528.971] (II) SynPS/2 Synaptics TouchPad: buttons: left right double triple
[ 528.971] (**) Option "SHMConfig" "true"
[ 528.971] (**) Option "MaxTapMove" "2000"
[ 528.971] (**) Option "VertEdgeScroll" "true"
[ 528.971] (**) Option "VertTwoFingerScroll" "true"
[ 528.971] (**) Option "HorizTwoFingerScroll" "true"
[ 528.971] (**) Option "TapButton1" "1"
[ 528.971] (**) Option "CircularScrolling" "true"
[ 528.971] (--) SynPS/2 Synaptics TouchPad: touchpad found
[ 528.971] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 528.971] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
[ 528.971] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 528.971] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 0
[ 528.972] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 528.972] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 528.972] (--) SynPS/2 Synaptics TouchPad: touchpad found
[ 528.972] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse0)
[ 528.972] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 528.972] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 528.972] (II) Synaptics touchpad driver version 1.2.2
[ 528.972] SynPS/2 Synaptics TouchPad no synaptics event device found
[ 528.972] (**) Option "Device" "/dev/input/mouse0"
[ 528.972] (**) Option "SHMConfig" "true"
[ 528.972] (**) Option "MaxTapMove" "2000"
[ 528.972] (**) Option "VertEdgeScroll" "true"
[ 528.972] (**) Option "VertTwoFingerScroll" "true"
[ 528.972] (**) Option "HorizTwoFingerScroll" "true"
[ 528.972] (**) Option "TapButton1" "1"
[ 528.972] (**) Option "CircularScrolling" "true"
[ 528.993] Query no Synaptics: 6003C8
[ 528.993] (--) SynPS/2 Synaptics TouchPad: no supported touchpad found
[ 528.993] (EE) SynPS/2 Synaptics TouchPad Unable to query/initialize Synaptics hardware.
[ 528.993] (EE) PreInit failed for input device "SynPS/2 Synaptics TouchPad"
[ 528.993] (II) UnloadModule: "synaptics"
[ 538.427] (II) Power Button: Close
[ 538.427] (II) UnloadModule: "evdev"
[ 538.427] (II) Video Bus: Close
[ 538.427] (II) UnloadModule: "evdev"
[ 538.427] (II) Power Button: Close
[ 538.427] (II) UnloadModule: "evdev"
[ 538.427] (II) Sleep Button: Close
[ 538.427] (II) UnloadModule: "evdev"
[ 538.427] (II) AT Translated Set 2 keyboard: Close
[ 538.427] (II) UnloadModule: "evdev"
[ 538.427] (II) UnloadModule: "synaptics"
Sorry guys I did not want to post but I am getting nowhere. I have used all the configs that wiki has suggested and disabled all that is suggested here http://andreascarpino.it/2010/04/xorg-1 … iguration/ and a few others on the forum (using second one down as current synpatics).
Any help is greatly appreciated. The touchpad worked on all previous versions of Xorg mainly with hal.Thanks for the response.
I am using dwm, I have found the mouse is actually invisible instead of not working. I have tried to rollback my kernel with no success unfortunately too many deps for other programs. I have also tried to rollback xorg with again no luck keeps saying evdev is a conflict when it's uninstalled.
I have also tried fbdev and vesa but both make my screen go but I can see the mouse in all the fuzzyness. -
Touchpad detected as ImPS/2 Logitech Wheel Mouse
I have an Asus laptop (not an eee pc), and my touchpad is detected incorrectly. It thinks it is a "ImPS/2 Logitech Wheel Mouse." I have tried to use the synaptics driver by configuring /etc/hal/fdi/policy/11-x11-synaptics.fdi
<?xml version="1.0" encoding="ISO-8859-1"?>
<deviceinfo version="0.2">
<device>
<match key="info.product" contains="ImPS/2 Logitech Wheel Mouse">
<append key="info.capabilities" type="strlist">input.touchpad</append>
</match>
<match key="info.capabilities" contains="input.touchpad">
<merge key="input.x11_driver" type="string">synaptics</merge>
<merge key="input.x11_options.SHMConfig" type="string">true</merge>
<merge key="input.x11_options.TapButton1" type="string">1</merge>
<merge key="input.x11_options.TapButton2" type="string">2</merge>
<merge key="input.x11_options.TapButton3" type="string">3</merge>
</match>
</device>
</deviceinfo>
but this causes the touchpad to stop working entirely. Here is the relevant section of my Xorg.0.log
(II) config/hal: Adding input device ImPS/2 Logitech Wheel Mouse
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules/input//synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.1.3
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(II) Synaptics touchpad driver version 1.1.3
(**) Option "Device" "/dev/input/event7"
(**) Option "SHMConfig" "true"
(**) Option "TapButton1" "1"
(**) Option "TapButton2" "2"
(**) Option "TapButton3" "3"
(--) ImPS/2 Logitech Wheel Mouse: no supported touchpad found
(EE) ImPS/2 Logitech Wheel Mouse Unable to query/initialize Synaptics hardware.
(EE) PreInit failed for input device "ImPS/2 Logitech Wheel Mouse"
(II) UnloadModule: "synaptics"
also here is the incorrect entry from /proc/bus/input/devices
I: Bus=0011 Vendor=0002 Product=0005 Version=0063
N: Name="ImPS/2 Logitech Wheel Mouse"
P: Phys=isa0060/serio4/input0
S: Sysfs=/devices/platform/i8042/serio4/input/input7
U: Uniq=
H: Handlers=mouse1 event7
B: EV=7
B: KEY=70000 0 0 0 0
B: REL=1036
Is there some way I can let my system know that this is indeed a touchpad so I can configure it properly?I can't really gather anything useful from dmesg. Here's the possibly relevant output:
$ dmesg | grep -i input
input: Macintosh mouse button emulation as /devices/virtual/input/input0
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input5
input: Asus Laptop extra buttons as /devices/virtual/input/input6
input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio4/input/input7
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:08.0/input/input8
$ dmesg | grep -i logitech
input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio4/input/input7
$ dmesg | grep -i -C 3 touchpad
asus-laptop: K40IN model detected
asus-laptop: Brightness ignored, must be controlled by ACPI video driver
input: Asus Laptop extra buttons as /devices/virtual/input/input6
Registered led device: asus::touchpad
usb 1-5: new high speed USB device using ehci_hcd and address 2
ACPI: Battery Slot [BAT0] (battery present)
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4d00
There's nothing about synaptics anywhere.
Is there anything potentially useful here? -
Windows 10 -problems with touchpad and two-finger scrolling
I upgraded to Windows 10, and the touchpad settings default to enable reverse scrolling direction with the two-finger scrolling. I disabled that, and it works all right.. But when I restart my computer, the change isn't saved and I have to do it all over again Is there any way to get the system to recognize the change to the settings after rebooting? I would think it would be simple, but even creating a separate profile doesn't work.
I upgraded to Windows 10, and the touchpad settings default to enable reverse scrolling direction with the two-finger scrolling. I disabled that, and it works all right.. But when I restart my computer, the change isn't saved and I have to do it all over again Is there any way to get the system to recognize the change to the settings after rebooting? I would think it would be simple, but even creating a separate profile doesn't work.
-
TouchSmart m6-k022dx Sleekbook Synaptic Touchpad not working
Hello,
A couple days ago, the touchpad on my TouchSmart m6 sleekbook stopped working with no apparent cause.
Things I've tried
Disabling and re-enabling touchpad through built in synaptic software
Uninstalling driver and restart computer (automatically reinstalling it)
Uninstalling from add/remove programs, and redownloading from HP website
What should i I do?@hm8 ,
Hello and thank you for posting on the HP support forums.
First thing you will want to try is a system restore to before you noticed the issue.
HP PCs - Using Microsoft System Restore (Windows 8)
This next link may be help as well.
HP Notebook PCs - Using and Troubleshooting the TouchPad or ClickPad (Windows 8)
Let me know how things go.
Thank you again for posting and have a great day.
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
D5GR
I work on behalf of HP
Maybe you are looking for
-
NAT issue - WRT54G Version 1.1 with Vista Home Premium
Router = WRT54G Version 1.1 I am trying to figure out the cause of my problems, this router or Vista? I have 2 PC's (just want to use my Vista 1) connected to the same router that is connected to a cable modem – the Windows XP machine has no problems
-
Plug-in/Folder Actions no work, Drop App works
I've been trying to get the automator actions from here (http://www.apple.com/pro/techniques/automator/) to work. I save the plug-in and activate it as a folder action script. When a new item is added the the folder the contains the action script, th
-
Changing sort order in Finder to display folder first
In almost every other release of OS X there was a tweak to edit the frameworks so that you could have finder, when sorting by "Kind/Type"you could display folders first. Well of course they broke that in Leopard. Has anyone discovered a way to reinst
-
Ko88 results in zero value - trying from AuC to Asset (full settlement)
Hi everybody, I´m getting a zero value doing a settle by KO88 from AUC to a final asset. Previously i have made the settle for AUC from expense with no ploblem. The problem is that when i make the settle with KO88 (full settlement option) to pass the
-
Crystal Reports 2011 Map Expert dialog box option
Hi When I select the Graduated option, then click the Customize button on this dialog box (on the Type tab) to select a different symbol for the map, I get the following error message - "Unable to find or load Helper dialog DLL. Is there a fix for th