Sync time differences between appointments on two macs?

Hi all.
I have just had to re-install all my data on my MacBook after a hard drive failure. All went well except I'm having problems with iCal?
I use two computers and when I sync with Mobile Me, all of the appointments are transferred to the right day, but they are just some four hours earlier? I notice that the thin line with a red dot on the left hand side going across iCal is in a different place on each computer on iCal. I think its position is throwing it all out somehow.
Does anyone know how to move this? I'm obviously missing something very obvious, but I can't seem to find a solution.
Hope someone can help!

Yetizone,
That thin line with a red dot is a current time and date stamp. It should reflect the time of your mac as well as the date. I would make sure that all of your computers are in the correct time zone. Also in the (Date and Time) Preference Pane found in (System Preferences) you can (Set date & time automatically) with apples servers. Also I would look into (ical)/(Preferences) click on the (Advance) tab and check (Turn on Time zone support) What that will do is put a little time zone thing back in the main window top right.
I hope that helps,
Weston

Similar Messages

Time Difference between iPhone calender and Mac iCal

I'm having trouble when syncing my iPhone to my Mac. All of the times I enter on my computer are correct, but when I sync my phone to through iTunes, all of the times are one hour behind on the phone. When I correct it through my phone and sync again, the time on the Mac is one hour ahead. Now I bought the computer in central time zone. I also had to trade my iphone due to a broken switch in the central time zone as well, but I live on the east coast. Could the fact that I activated the phone in the midwest but live in the east be the reason for this?

Sorry for hasty posting. Deep in the setup, under Mail, Contacts, Calendar, the Calendar was set to Cupertino and I am in Prague. That is why, stupid me ...

How to measure time difference between two continous encoder pulse (PULSE A & PULSE B)

im trying to figure out the time difference between two square
wave pulse (PULSE A and PULSE B) from an encoder. I tried to modify many code but fail to capture thephase difference for each pulse. the
pulse only rise to 5V and fall to 0V like normal square wave pulse
can you and all of experts here help me out with this?
my problem
1) Encoder pulse are continous (pulse A and pulse B)
2) Square wave pulse have "0V" and "5V" please rapidly
if possible someone show me correct method , Im using LABVIEW 7.1 and Hardware NI SCOPE (PCI 5102)
your advice are highly appreciated
among my idea as in attachment , but I failed to get it
Attachments:
Need to Get this wave.JPG ‏34 KB

Hi Amirul,
Check the attached JPG file. i think this will be use full to you
Regards,
Santhosh M

Time difference between Mac & Windows

I have just successfully installed Windows XP SP2 using boot camp. But the clock in Mac and Windows are always different, for example, if i am running Mac and time is 4.00 p.m; then I restart in Windows, the time in Windows now is 8.00p.m. If then I changed time in Windows and restart again in Mac, the clock in Mac is 12.00p.m (4 hours late). I have tried several times but it stays the same. Is there anyone having the same problem as mine?
ah, 1 more small thing, when using Windows, which button in Mac keyboard is for printscreen? In the manual for Bootcamp, it is said that using fn+f11 but it doesn't work???

autumn_fail:
For Print Screen try using Fn-Shift-F11 combination. Also read *[_This Article_|http://support.apple.com/kb/HT1220]*.
As far as your question on the Time difference between Windows and OSx, this is a known issue with Windows and OSx running on a mac. This has to do with how both Operating Systems set the time. One way to handle this is to run time preferences as soon as you log into OSx (after logging out of Windows). Its a pain nonetheless.
Please *[_Click Here_|http://discussions.apple.com/thread.jspa?messageID=7965906&#7965906]* for more information on this subject.
Axel F.

How to measure time difference between zero crossing of a sine wave and rise time of a pulse on a same graph?

I have a 50Hz sine wave and a pulse signal on a same graph. The phase difference between two is between 0-90 degrees.
Now I need to calculate the time difference between (when the sine wave crosses zero volts) and (when the pulse rises). The frequency will stay approximately same for both signals.
The application is for a three phase generator. In simple words, when the time difference between the zero-crossing of sine wave and the pulse rises increases, that means that the load on the generator has increases.
I am a beginner user of LabView (version 9, 2009), maybe it is a very simple problem but I've been pulling my hair out for the last few days and coudln't figure anything out. Any help would be greatly appreciated. I am using DAQ USB-6008 to measure these voltages and pulse from the generator and a sensor
I have attached a jpg (a graph that i just made with excel to explain). The time 't' is what I am trying to measure
Cheers
Awais
Message Edited by awais.h on 03-30-2010 11:20 PM
Message Edited by awais.h on 03-30-2010 11:21 PM
Solved!
Go to Solution.

Hi
Thanks for the code but I'm afraid it won't work. Like you said the probability of choosing a value that is on both graphs may not happen. This is something that I would like the code to do automatically.
But I did use the previous code posted and made some modifications to it and it seems to work perfectly. Now the next thing is to be able to get just that one value that tells you the first time difference.
Here is what I get using that code.
As you can see from the t Values. I only need the one that is highlighted. If there is a way to filter out the rest it would be great.
I was thinking of a while loop and as soon as the value is higher than 3E-5 it would store the number and stop the loop, but I'm not too familiar with arrays in labview.
Here is the the code modified.
As you can see, it wasn't that big of a modification and it still is your code.
I will keep trying.
Thanks for the help
Attachments:
FinalShockSpeed.vi ‏55 KB

Is there a difference between microsoft office for mac and for windows?

As a college student it's important that everything is equal for windows and mac for using instructions. So i am wondering if theres a difference between microsoft office for mac and for windows?

There are differences between the two version of Office. If you need to be exactly like the Windows version, you will have to run Windows on your Mac.
Allan

How to calculate the Time difference between 2 dates

HI All,
I am using HR_hk_diff_btw_2_dates to calculate the employee service dates.
For that i am inputing his hire date and Term dates and Output format as '05' i am getting output perfectly....
But problem is whe i am inputting the employee hire date is Dec 1 2007 and Term date is
March 31 2009 It is coming as 1 year 3 months 31 days instead of 1 year 4 months directly .......How could we make it make last date also working day and get the O/p as 1 year 4 months ?Please Advice..
Regard
sas

1. FM for difference betwwen two times:SCOV_TIME_DIFF
Import parameters               Value
IM_DATE1                        2008-01-01
IM_DATE2                        2008-01-01
IM_TIME1                        10:00:00
IM_TIME2                        11:30:00
Export parameters               Value
EX_DAYS                         0
EX_TIME                         01:30:00
2. SD_CALC_DURATION_FROM_DATETIME : Finds the difference between two date/time and report the difference in hours
L_MC_TIME_DIFFERENCE : Finds the time difference between two date/time

Time difference between the Identity system and Access System: OAM

I was installing OAM. Performed the below steps.
-installed identity server
-installed webpass
-setup of identity system console
-installed policy manager
-setup of access system console
The above steps were successfull. Then when i was logging into Access system console, i am getting the below error:
Error:there was a problem obtaining the userid. One possible reason for this is a time difference between the Identity system and Access systems (Policy Manager and Access system console).+
The Identity Server, WebPass and Policy Manager are installed on the same machine.
Userdata repository: OVD 10.1.4.3
Policy and Config Data Repository: OID 11.1.1.3
OAM: 10.1.4.3
Windows2008 - 64bit
Found document in metalink similar to this issue. suggested to change ldapmaxofreties. but didn't help.
Any idea on this error. Please Advise.
Thanks in advance.

Try this::
Check Time Difference Between Identity and Access Manager Systems
Check the logfile in the Access Manager install directory. The default location is <$AMinstall_dir>/access/oblix/logs/oblogfile.
If the file exists and it contains following line "skew = slack = " that means the Identity and Access Manager Web Servers are on different machines and have not synchronized time within a minute.
Either synchronize times between the two machines within a minute's accuracy or you can increase the slack by modifying these two files: <$AMinstall_dir>/access/oblix/apps/common/bin/oblixbaseparams.lst: loginslack: <$IMinstall_dir>/identity/oblix/apps/common/bin/oblixbaseparams.xml: loginslack: where numofseconds is more than skew found in the oblogfile.
For example, if you have following line in oblogfile "skew = 121 slack = 60", set numofseconds in the two parameter files to 130. After doing this, Stop the Identity Manager Web Server. Then stop the Identity Server. Start the Identity Server.
Then start the Identity Manager Web Server. Start a new browser session and see if you get the same error.

How to calculate the % of time difference between different state

Hi there,
The below query returns the follwoign outptut. I need to calculate the % of time period that a specific state ( state ex: open or closed or all report )exists.
I have to find the time difference between the 2 states . How could I do that ?
The first row shows null for the previous state . How could get actual previous state for the first row?
SELECT si.station_name,
                vppstation.avi_control_state_code.STATE_SHORT_NAME,
                ash.state_id ,
                lag(ash.state_id) over (order by ash.STATE_EFF_DATE desc) previous_state,
                TO_NUMBER(TO_CHAR(ash.state_eff_date, 'SSSSS')) "periods in sec",
                TO_CHAR(ash.state_eff_date, 'dd-mon-yyyy hh24:mi:ss am') "Date"
           from vppstation.avi_state_history ash
left outer join vppstation.avi_control_state_code
             on ash.state_id = vppstation.avi_control_state_code.state_id
LEFT OUTER JOIN vpproadside.stations_installed si
             ON ash.station_id = si.station_id
          where ash.state_eff_date >= to_date('28/02/2010', 'dd/mm/yyyy')
            and ash.state_eff_date <= to_date('03/03/2010', 'dd/mm/yyyy') ;
       group by si.station_name
                     ash.state_id
       order by ash.state_eff_date asc ;
STATION_NAME                   STATE_SHORT_NAME STATE_ID               PREVIOUS_STATE         periods in sec         Date
IRDNCST02                      Open             1                    NULL                  85166                  01-mar-2010 23:39:26 pm
IRDNCST02                      All Report       3                      1                      85159                  01-mar-2010 23:39:19 pm
IRDNCMT01                      Closed           2                      3                      81376                  01-mar-2010 22:36:16 pm
IRDNCST02                      Open             1                      2                      78723                  01-mar-2010 21:52:03 pm
IRDNCST02                      All Report       3                      1                      76023                  01-mar-2010 21:07:03 pm
IRDNCMT01                      Open             1                      3                      55922                  01-mar-2010 15:32:02 pm
IRDNCMT01                      Closed           2                      1                      54931                  01-mar-2010 15:15:31 pm
IRDNCHA01                      Closed           2                      2                      41291                  01-mar-2010 11:28:11 am
IRDNCAS01                      Open             1                      2                      38847                  01-mar-2010 10:47:27 am
IRDNCAS01                      All Report       3                      1                      37947                  01-mar-2010 10:32:27 am
IRDNCST02                      Open             1                      3                      35332                  01-mar-2010 09:48:52 am
IRDNCST02                      All Report       3                      1                      32632                  01-mar-2010 09:03:52 am
IRDNCST02                      Open             1                      3                      31502                  01-mar-2010 08:45:02 am
IRDNCST02                      All Report       3                      1                      28802                  01-mar-2010 08:00:02 am
IRDNCHI01                      Open             1                      3                      25368                  01-mar-2010 07:02:48 am
IRDNCHI02                      Open             1                      1                      23939                  01-mar-2010 06:38:59 am
IRDNCMT01                      Open             1                      1                      20696                  01-mar-2010 05:44:56 am
IRDNCCH02                      Open             1                      1                      13452                  01-mar-2010 03:44:12 am
Edited by: Indhu Ram on Mar 11, 2010 1:34 PM
Edited by: Indhu Ram on Mar 11, 2010 2:20 PM

If you look at the table which is output of the given query , there is column called "STATE_ID" It shows the current state ie open or closed or all report.
The column 'PREVIOUS_STATE' shows the state before the current state. .In the table in 2nd row in previous_state column there is state_id = 1 (open)which is the state before 'all report state'

Execution time difference between SELECT & UPDATE statement in JDBC Sender.

Hi Experts,
In my scenario, I have used the JDBC Sender Adapter with the SELECT and UPDATE statement.
Now the problem is in between the execution of Select and update statement, few more entries are coming in the same DB Table.
So result of this is updation take place for those entries which are not even picked up by the select statement.
Can we avoid this execution time difference between the SELECT & UPDATE statemet on JDBC Sender side???
Thanks & Regards
Jagesh

Hi
Use serializable option in additional parameters, now all new entries would also be updated.

How can I measure the time difference between spikes (interspike intervals)

I have used NI USB-6008 (DAQ) to sample a continous signal, after sampling I compared the amplitude of the resulted signal with a value. If the amplitude is greater than a specific value (threshold) then it can pass. Now I want to measure the time difference between the resulted samples. The samples look like spikes. (May be if I trigger a timer, then I can measuer the time difference, but I have not seen such a timer).
Thanks in advance,
Saraydin

Oops just occured to me that you are using a 6009 which is not very fast, 48ks/sec, this will not get you very much time resolution and you could have issues seeing much of a 50 us sample. Another approach is to use the counter but you would have to preprocess the spikes to generate a trigger for the counter.
Paul
Paul Falkenstein
Coleman Technologies Inc.
CLA, CPI, AIA-Vision
Labview 4.0- 2013, RT, Vision, FPGA

8 hours time difference between Mac OS & Windows XP for Macbook

I got my macbook yesterday. Next to the problems I've heard before,today I found that the time for MAC OS is always 8 hours before the time in Windows XP no matter how I adjust the time zone. I've tried many ways, but found no way out. Is there somebody else can give me some tips. Tks!

I got my macbook yesterday. Next to the problems I've
heard before,today I found that the time for MAC OS
is always 8 hours before the time in Windows XP no
matter how I adjust the time zone. I've tried many
ways, but found no way out. Is there somebody else
can give me some tips. Tks!
Official answer
http://docs.info.apple.com/article.html?artnum=303572#faq1
Why is the time different between Mac OS X and Windows XP on my computer?
The Windows XP and Mac OS X operating systems handle your computer's date and time information differently, so the date and time may be different when you switch operating systems. For best results, use a network time server and resync the date and time whenever you switch operating systems. In Mac OS X, use the “Set date & time automatically” option in the Date & Time preferences. In Windows XP, click the Update Now button in the “Date and Time Properties” control panel.
Nice solution
http://discussions.apple.com/message.jspa?messageID=2378497#2378497
"I found a better solution to this whole thing. The problem with the Windows clock being off is because the hardware clock (the one on your actual motherboard) is being set to "Universal" time, or GMT, when you shut down your MacOS bootup. When you boot Windows, Windows assumes your clock is set to your local timezone because that's what Windows does by default. This explains why the people who set their MacOS clock to GMT got the right time in Windows... If the hardware clock is being set to "GMT," when it's actually the local time, Windows will pick this setting up as local time as it did before.
To fix this, you need to add a key to your Windows system registry to tell Windows that your hardware clock will always be GMT.
* WARNING: Editing your registry improperly can render your Windows installation inoperable. Proceed VERY carefully. I am not responsible if you mess something up. *
The short solution for people who know how to edit the registry:
A DWORD key called HKEYLOCALMACHINE\SYSTEM\CurrentControlSet\Control\TimeZoneInformation\RealTimeIsUniversal needs to have the value of "1"
The step-by-step solution is as follows:
1. Boot Windows
2. Click Start --> Run and type regedit. Click OK
3. The Windows Registry Editor should pop up. Navigate within the explorer to:
HKEYLOCALMACHINE\SYSTEM\CurrentControlSet\Control\TimeZoneInformation
4. Click on the TimeZoneInformation "folder" from the navigation pane if you haven't already done so.
5. This assumes the correct key doesn't exist. If it does, you will just change the existing key's value: Right click on the white space within the folder (If you don't have a right mouse button, you may need to download a program called applemouse to emulate the "control-click" of the apple 1-button mouse). Select new --> DWORD Value. Title the key "RealTimeIsUniversal" (No quotes). Set the value to "1" (No quotes again). Hexidecimal should be fine.
6. Either reboot and set the clock in MacOS or set the clock in Windows. You should now be able to reboot into either OS and have a correct clock."
iFelix

Sync file cut express project on two macs

I have a imac and a macbook what is the best way to sync a project back and forth between the two macs. I know probably the original video files will have to be on both. I'm guessing that file should be in the same place on both. But I need step by step on how to. With all my FCE files in one folder so all I have to sync is one folder between the two.
Thanks

Hi(Bonjour)!
kpriest1 wrote:
I have a WD 750gb Hard Drive on my imac partitioned 2 times 500gb for time machine and 250 just for FCE scratch disk files. I can log on to my macbook via wireless network and transfer files back and forth. I'm just not sure of all the files FCE uses when working on a movie. I think if I knew what files they are I could lump them together in one folder and copy that folder back and forth to each other via wireless. As long as path is the same on both mac. I'm just not sure and need someone that's maybe been there.
Keith
Wireless connection is a bad idea as data rate transfer speed needed for video material is pretty fast. I'm sure that your macbook air hard drive is not designed to give a sustained data rate tranfer speed for a such usage.
Partitionning is a bad idea too as your internal drive has to seek for data stored on 2 logical locations fitted on just one physical support. It seems many many actuator stop and go and less efficient data rate transfer speed.
I maintain my suggestion, go for a dedicated external hard drive where you will put all media related to your project AND the project file itself. If FCE is correctly installed on both mac, your project will open flawlessly from one mac or other.
Michel Boissonneault
Message was edited by: Michel Boissonneault

How to find out time difference between 2 consecutive characters coming in

Hi
Data is coming on serial port and m taking this data in a input stream.I need to know the time difdference between consecutive characters.Any ideas?

What do you mean? If you meassure the time between two characters, you want to calculate how accurate it is? First you would need to find out how accurate the System.currentTimeMillis is on the platform you run on. That may be easy
long start = System.currentTimeMillis();
long end;
while ((end = System.currentTimeMills()) == start);
long delta = end - start;But sometimes (on win98) it reports 50, other times 60. So its not quite accurate. But you could redo that test a couple of times and take the avg or the max.
Then if you get a time difference of 0ms between two characters, you know it will be somewhere 0 and 60ms. If you get 60ms between two characters, you know it will be somewhere between 0 and 120 ms. It's +/- delta seconds accurate.
Would this be a way to calculate the percentage accuracy: 100.0-100.0*delta/(time+delta)
Still better to meassure the time over more than just 2 characters unless it is a very slow stream.

Time difference between to times

I'm trying to create an sign in and sign out sheet that enters the daily time and date you sign in. I also want when I leave for the end of the day it enters the time when out clock out. I want it to calculate the total hours worked, for example: if I
sign in at 7:00 I get off at 3:30, because I get 30 minutes for lunch. I'm new to SharePoint and don't know how to get it started. Thanks

you can create a calculated/computed column to determine the difference between two dates (just use =[EndDate]-[StartDate])... but there is nothing in SharePoint that takes into account who will "get 30 minutes for lunch", or how those business
rules would work.
Scott Brickey
MCTS, MCPD, MCITP
www.sbrickey.com
Strategic Data Systems - for all your SharePoint needs

Sync time differences between appointments on two macs?

Similar Messages

Maybe you are looking for