Synchronization error between LMDB and SMSY
Hello Experts
I have a sync error between LMDB and SMSY entries. I want your help to make this synchronization to Solution Manager 7.1 SP07.
Thank you very much for your help
Juan Carlos Salazar R
Solman Setup - Configuration Lost
To try to solve the synchronization error
I have been running a Report for get some information and as a consequence all the information into the solman configuration was lost. I mean everything, all the clock (the date of modification) are in zero, and all the status are grey.
Someone know How to bring this information back; without performing a backup or to perform a setup again.
The report is the RLMDB_SYNC_TECHNICAL_SYSTEM
Similar Messages
-
Synchronization Error between ARIS and SolMan
When running the syncrhonization from ARIS to Solution Manager I am getting the following error on several of my objects:
NOTE: The '<folder name>' item was skipped because the symbol type is ignored during synchronization.
Any ideas?Hello Samuel,
did you contact ids-scheer support yet ([email protected]). They can send you a detailed list of required priviledges. It is more then just the ones you have now since additional RFC are called.
Regards,
Sinje -
Any SAP Note for RFC Error between BI and ECC 5.0
Hi..
the RFC Destination between BI and ECC 5.0 is giving errors.
Plz let me know if there is any Support pack or any solution to fix this error.
thanks..Hi,
pls find the RFC connection details
1 Prerequisites
1.1 User Roles
Use
With the Building Block Connectivity a configuration role for each component is provided to access all transactions relevant for the installation. The following roles are available:
Technical name Description File name for upload
B02_01C B02 - Connectivity Configuration Role (SAP R/3) B02_01C.SAP
B02_03C B02 - Connectivity Configuration Role (SAP BW) B02_03C.SAP
C71_04C B02 - Connectivity Configuration Role (SAP CRM) C71_04C.SAP
B02_04C_SRM B02 - Connectivity Configuration Role (SAP SRM) B02_04C_SRM.SAP
Procedure
Please upload the necessary roles and add them to your user, using transactions PFCG (Role Maintenance).
2 Local Settings
This chapter describes all local settings that are necessary for each component like SAP R/3, SAP SCM, SAP BW, SAP CRM or SAP SRM.
2.1 SAP R/3
2.1.1 Define Client Administration (SAP R/3)
Use
This activity allows you to change Customizing settings.
Prerequisites
You have logged on to the system in English in order to start with the installation of the Best Practices Scenario.
Procedure
Run the following activity:
SAP R/3 Role Menu Define Client Administration (SAP R/3)
Transaction Code SCC4
SAP R/3 Menu Tools Administration Administration Client Administration Client Maintenance
Then carry out the following steps:
1. Choose Display Change.
2. Confirm the warning message Caution: The table is cross client.
3. Select your SAP R/3 client and choose Details.
4. In the Change View Clients: Details screen, activate the following settings:
u2022 Automatic recording of changes
u2022 Changes to Repository and cross-client Customizing allowed
u2022 eCATT and CATT allowed.
5. Save.
6. Go back to the SAP Easy Access menu.
2.1.2 Defining a Logical System for SAP R/3 (SAP R/3)
Use
The purpose of this activity is to create a logical system for your SAP R/3 System. To enable communication between systems within your system landscape, you must
1. Define the systems as logical systems.
2. Assign the logical system for the SAP R/3 System to a client.
This enables the systems to recognize the target system as an RFC destination. If the logical system has already been created, skip this activity.
Logical systems are defined cross-client.
Procedure
Carry out the following steps:
1. Access the transaction using:
SAP R/3 Role Menu Defining a Logical System for SAP R/3 (SAP R/3)
Transaction Code SPRO
SAP R/3
IMG Menu Basis Components (for R/3 Enterprisse: SAP Web Application Server) Application Link Enabling (ALE) Sending and Receiving Systems Logical systems Define Logical System
2. Choose New entries.
3. In the column Log System, enter a name for the logical system that you want to create.
4. In the column Name, enter a description of the logical system.
Log. System Name
where XXX is the system name
and NNN is the client.
5. Save your entries.
A transport request for Workbench appears.
6. Select an existing request or create a new request, if necessary.
A transport request for Customizing appears.
7. Select an existing request or create a new request, if necessary.
2.1.3 Assigning Logical System to Client
Use
The purpose of this activity is to make an assignment for the logical system. Skip this activity if a logical system is already assigned to your client.
Procedure
Carry out the following steps:
1. Access the transaction using:
SAP R/3 Role Menu Assign Logical System to Client
Transaction Code SCC4
SAP R/3 Menu Tools Administration Administration Client Administration Client Maintenance
2. Choose Display ® Change.
3. Confirm the warning message The table is cross client.
4. Select your R/3 client and choose Details.
5. Enter the name of the logical system of your SAP R/3 client.
6. Save and confirm the warning message Be careful when changing the logical system.
7. Choose Back twice.
2.1.4 Creating an RFC User (SAP R/3)
Use
To enable communication between the SAP R/3 back-end system and the SAP SCM System, you have to create an RFC user in the SAP R/3 System.
The RFC user in the application client enables multiple RFC connections. Skip this activity if an RFC User has already been created.
Procedure
Carry out the following steps:
1. Access the transaction using:
SAP R/3 Role Menu Creating an RFC User (SAP R/3)
Transaction Code SU01
SAP R/3 Menu Tools Administration User Maintenance Users
2. In the User field, enter RFCUSER.
3. Choose Create.
4. On the Maintain User screen, enter the following data on the Tab entry screens:
Address
Last Name
Function
Logon data
User type System
Password LOGIN
Profile
Profiles SAP_ALL
SAP_NEW
S_BI-WX_RFC
Defaults
Logon Language EN
5. Save your entries.
2.3 SAP BW
2.3.1 Define Client Administration
Use
This activity defines changes and transports of the client-dependent and client-independent objects.
Procedure
1. To perform this activity, choose one of the following navigation options:
SAP BW Role Menu Local Settings ® Define Client Administration
Transaction Code SCC4
SAP BW Menu Tools Administration Administration Client Administration Client Maintenance
2. Switch to change mode.
3. Select your client.
4. Choose details.
5. In field Currency enter the ISO-code of the local currency, e.g. USD or EUR.
6. In field Client Role enter Customizing
7. Check the settings for changes and transport of client-specific objects and client-independent object changes
If you want to use the settings made by BC-Sets or manually in other systems (other than BW), u201CAutomatic recording of changesu201D and u201CChanges to Repository object and cross-client Customizing allowedu201D is required.
Result
Client administration has been defined to support the installation using Best Practices.
2.3.2 Defining a Logical System for SAP BW (SAP BW)
Use
In this step, you define the logical systems in your distributed system.
Prerequisites
Logical systems are defined cross-client. Therefore cross-client customizing must be allowed in your client (this can be checked in transaction SCC4).
Procedure
To carry out the activity, choose one of the following navigation options:
SAP BW Role Menu Defining a Logical System for SAP BW (SAP BW)
Transaction Code SPRO
IMG Menu SAP Reference IMG SAP Customizing Implementation Guide SAP NetWeaver Business Information Warehouse Links to other Systems General Connection Settings Define Logical System
1. A dialog box informs you that the table is cross-client. Choose Continue.
2. On the Change View u201CLogical Systemsu201D: Overview screen, choose New entries.
3. On the New Entries: Overview of Added Entries screen enter the following data:
Field name Description R/O/C User action and values Note
Log. System Technical Name of the Logical System Enter a name for the logical BW system that you want to create
Name Textual Description of the Logical System Enter a clear description for the logical BW system
4. Choose Save.
If a transport request for workbench and customizing is displayed choose existing requests or create new requests.
If you want to continue with the next activity, do not leave the transaction.
Result
You have created a Logical System Name for your SAP BW client.
2.3.3 Assigning Logical System to Client (SAP BW)
Procedure
To carry out the activity, choose one of the following navigation options:
SAP BW
Role Menu Assigning Logical System to Client (SAP BW)
Transaction Code SCC4
SAP BW Menu Tools Administration Administration Client Administration Client Maintenance
1. In the view Display View "Clients": Overview, choose Display. Change
2. Confirm the message.
3. Select your BW client.
4. Choose Details.
5. In the view Change View "Clients": Details, insert your BW system in the Logical system field, for example, BS7CLNT100.
6. Save the entries and go back.
2.3.4 Opening Administrator Workbench
Procedure
To carry out the activity, choose one of the following navigation options
SAP BW Modeling Administrator Workbench: Modeling
Transaction Code RSA1
1. In the Replicate Metadata dialog box, choose Only Activate.
2. If a message appears that you are only authorized to work in client ... (Brain 009) refer to SAP Note 316923 (do not import the support package, but use the description under section Workaround).
2.3.5 Creating an RFC-User (SAP BW)
Procedure
To carry out the activity, choose one of the following navigation options:
SAP BW Role Menu Creating RFC User
Transaction Code SU01
SAP BW Menu Tools Administration User Maintenance Users
Then carry out the following steps:
1. On the User Maintenance: Initial Screen screen:
a. Enter the following data:
Field Entry
User RFCUSER
b. Choose Create.
2. On the Maintain User screen:
a. Choose the Address tab.
b. Enter the following data:
Field Entry
Last Name RFCUSER
Function Default-User for RFC connection
c. Choose the Logon data tab.
d. Enter the following data:
Field Entry
Password LOGIN
User type System
e. Choose the Profiles tab.
f. Enter the following data:
Field Entry
Profiles SAP_ALL , SAP_NEW and S_BI-WHM_RFC
g. Choose Save.
Do not change the password of this user as it is used in RFC connections.
2.3.6 Define RFC-USER as default (SAP BW)
Procedure
To carry out the activity, choose one of the following navigation options
SAP BW Role Menu Define RFC-USER as default (SAP BW)
Transaction Code RSA1
SAP BW Menu Modeling Administrator Workbench: Modeling
1. On the Administrator Workbench: Modeling screen choose Settings Global Settings.
2. In the Global Settings/Customizing dialog box choose Glob. Settings.
3. On the Display View u201CRSADMINA Maintenance Viewu201D: Details screen:
a. Choose Display Change.
b. Enter RFCUSER in the BW User ALE field.
c. Choose Save.
Hope this helps in solving u r problem
Regards
Ramakrishna Kamurthy -
Synchronize date between OUD and AD
Hi all.
I want to synchronize date between OUD(Oracle Unified Directory) and AD (Windows Active Directory).
OIM(OID ODIP)?
This framework is very powerful, but it seems to be a liitle heavy for me.
Is there any solution more light and straight to reach the goal?
I would appreciate for any reply.Hi,
You don't need OID as you can use OUD as DIP configuration store.
The procedure is described in detail in KM note 1511847.1 available from support.oracle.com
The note 1511883.1 can be useful as well as it is a placeholder for DIP/OUD related procedures.
-Sylvain -
Crc error between 2950 and 3620 router
I have connected the 2950 to the 3620, and the running-config of 2950 below:
2950#show running-config
Building configuration...
Current configuration : 1279 bytes
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname 2950
enable secret xxxx
no ip subnet-zero
no ip finger
no ip domain-lookup
interface FastEthernet0/1
duplex half
speed 10
interface FastEthernet0/2
interface FastEthernet0/23
interface FastEthernet0/24
interface FastEthernet0/24.122
interface FastEthernet0/24.123
interface Vlan1
bandwidth 10000
ip address 192.168.10.200 255.255.255.0
no ip route-cache
delay 100
ip default-gateway 192.168.10.254
no ip http server
line con 0
transport input none
line vty 0 4
password xxx
login
line vty 5 15
login
end
And the 3620 router just set the interface ethernet0/3:
interface Ethernet0/3
ip address 192.168.10.254 255.255.255.0
half-duplex
I have connected the f0/1 of switch to the eth0/3 of router. There are many crc errors between the switch and router, and try to change the duplex and speed rate, but it didn't take effect. I ensure the cable is good.
Thank you for your suggestion!First, thank you for your notice of my problems.
Yes. When I ping from both directions, I'm seeing the CRC error only in the switch. And I have cleared the counters in both ends.
And I try to connect to another port of the router, It exists the same problem.
I'm seeing both of the input errors and CRC errors.
The interface of f0/1 (in switch)is following:
2950#show int f0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Fast Ethernet, address is 0007.84fc.d1c1 (bia 0007.84fc.d
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 219/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 10Mb/s
input flow-control is off, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:03:10, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:11:25
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 1000 bits/sec, 1 packets/sec
5 minute output rate 1000 bits/sec, 3 packets/sec
299 packets input, 39511 bytes, 0 no buffer
Received 5 broadcasts, 0 runts, 0 giants, 0 throttles
164 input errors, 164 CRC, 0 frame, 0 overrun, 33 ignored
0 input packets with dribble condition detected
1058 packets output, 81544 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
2950# -
Synchroniz​ation between DAC and ADC on NI 4451
I need for my DAC and ADC software buffers to line up with each other in analog time.
I'm using the following code to start the DAC and ADC conversions:
status = WFM_Group_Control (deviceNumber, group, START);
if (status==0)
status = SCAN_Start (deviceNumber, (short *)ADCbinArray, total_samples*SENSOR_CHANNELS, sampTimebase, sampInterval, scanTimebase, scanInterval);
But I end up with a 70-75 millisecond delay between the DAC start and the ADC start. I need synchronization to at least a few hundred microseconds between the DAC and ADC buffers.One clarification point is needed her. Yes, it is true that both the Analog Input and Analog Output of the 4451 use the same clock source. However, the way you currently have the start of these operations is to start each one separately through a software call. This is why you are not about to get better than millisecond resolution.
You can achieve hardware-timed synchronization of your input and output operations using RTSI to share a hardware start trigger for both the input and output. The idea is that you will route the start trigger of one operation to a RTSI line. Then tell the other operation to use the same RTSI line as its start trigger.
Even thought the RTSI bus is used to pass this signal from the AI circuitry to the AO trigger, there
is no need to connect a RTSI cable. In DSA devices, the analog input and output are automatically phase locked. There will be no phase drift between the input and output sample clocks, and minimal phase difference if they are running at the same rate. -
Real Time Integration Document - Rounding Error between LC1 and LC2
Hi!
We recently underwent currency conversion. After the conversion, we noticed that Real Time Integration document that is generated due to Assessment Run (KSU5) produces a document which are off by cents between LC1 and LC2 ,even though both have the same currency
LC1 = EUR (Currency Type 10 - Company Code Currency)
LC2 = EUR (Currency Type 60 - Global Company Currency)
Document being generated
Document Currency = USD (Controlling Area Currency)
Account LC1 (EUR) LC2 (EUR)
XXX 2297.44 2297.43
Any help would be appreciated .Hello Manish,
I am encountering the same issue. Have you found solution on this.
BR,
Zulfikar -
10Gig (tengigabit) CRC Errors between N5K500 and 3750X
Dear Forum,
We have an issue with a 10 Gig connection between a Nexus 5548 and a 3750X 10Gig. There is also a HSRP group running over this link with aggressive timeouts which recently behaves somewhat unstable. We noticed a bunch of CRC errors on this link on the 3750X side (about 300 per hour) and assume that these are related to the HSRP troubles once or twice a day.
Originally the connection was made with a twinax cable. We already changed to MMF fiber with SR SFP+'s. The 10Gig Uplink Module in the 3750x has been replaced already. All to no avail. Now it's up to replace the 3750 (receives CRC) or the Nexus Chassis (sending device)
I was wondering if there is some experience on the list what is the most probably cause and solution here.
Thanks in advance,
Michael.MTU is 1500 bytes, on both sides (I think) see output below. Strangely enough the NX has a non-zero Jumboframe counter (increasing).
C3750#sh int te3/1/1
TenGigabitEthernet3/1/1 is up, line protocol is up (connected)
Hardware is Ten Gigabit Ethernet, address is 4055.3992.111d (bia 4055.3992.111d)
Description: TO_100C_PO913
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 2/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-SR
Media-type configured as connector
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:55, output 00:00:41, output hang never
Last clearing of "show interface" counters 04:10:35
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 4011000 bits/sec, 1091 packets/sec
5 minute output rate 110431000 bits/sec, 16489 packets/sec
37040147 packets input, 35868731879 bytes, 0 no buffer
Received 1071851 broadcasts (935322 multicasts)
0 runts, 0 giants, 0 throttles
1002 input errors, 1002 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 935322 multicast, 0 pause input
0 input packets with dribble condition detected
182446795 packets output, 69097435882 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
C3750#sh int te4/1/1
TenGigabitEthernet4/1/1 is up, line protocol is up (connected)
Hardware is Ten Gigabit Ethernet, address is 4055.39bd.001d (bia 4055.39bd.001d)
Description: TO_100D_PO913
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-SR
Media-type configured as connector
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:14, output 00:00:33, output hang never
Last clearing of "show interface" counters 04:10:38
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 161000 bits/sec, 215 packets/sec
5 minute output rate 29493000 bits/sec, 9580 packets/sec
3264201 packets input, 318586322 bytes, 0 no buffer
Received 1130048 broadcasts (1020339 multicasts)
0 runts, 0 giants, 0 throttles
501 input errors, 501 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 1020339 multicast, 0 pause input
0 input packets with dribble condition detected
168673910 packets output, 87266013753 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
N5K connected to 3/1/1:
Ethernet1/1 is up
Hardware: 1000/10000 Ethernet, address: 0005.9b1f.8648 (bia 0005.9b1f.8648)
Description: CHANNEL_TO_RO015A
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 3/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 10 Gb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 2d04h
Last clearing of "show interface" counters never
30 seconds input rate 96695496 bits/sec, 16464 packets/sec
30 seconds output rate 4715024 bits/sec, 1868 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 148.33 Mbps, 20.23 Kpps; output rate 2.90 Mbps, 1.13 Kpps
RX
26173471641 unicast packets 6446061938 multicast packets 24295222 broadcas
t packets
32643828801 input packets 16853116460189 bytes
7772805495 jumbo packets 0 storm suppression packets
0 runts 0 giants 0 CRC 0 no buffer
0 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard
0 Rx pause
TX
48369101239 unicast packets 462061134 multicast packets 81589744 broadcast
packets
48912752123 output packets 56533126796163 bytes
35421478216 jumbo packets
6 output errors 0 collision 0 deferred 0 late collision
0 lost carrier 0 no carrier 0 babble 0 output discard
0 Tx pause
3 interface resets
N5K connected to 4/1/1:
Ethernet1/1 is up
Hardware: 1000/10000 Ethernet, address: 0005.9b1f.8188 (bia 0005.9b1f.8188)
Description: CHANNEL_TO_RO0015A
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 10 Gb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 2d04h
Last clearing of "show interface" counters never
30 seconds input rate 20643816 bits/sec, 10541 packets/sec
30 seconds output rate 142592 bits/sec, 180 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 25.50 Mbps, 9.49 Kpps; output rate 159.20 Kbps, 142 pps
RX
119855915845 unicast packets 6017690609 multicast packets 20318382 broadca
st packets
125893924837 input packets 124351081100162 bytes
70763564145 jumbo packets 0 storm suppression packets
0 runts 0 giants 1 CRC 0 no buffer
1 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard
0 Rx pause
TX
20958491666 unicast packets 503446052 multicast packets 52796318 broadcast
packets
21514734036 output packets 29748981423583 bytes
18964491576 jumbo packets
0 output errors 0 collision 0 deferred 0 late collision
0 lost carrier 0 no carrier 0 babble 0 output discard
0 Tx pause
3 interface resets -
Synchronize files between PC and Macbook Pro
Hi all,
I have a Macbook Pro and I have a Compaq desktop PC. I take the laptop around with me to work on and I also want to start using the PC at home to do work. I would like to synch the files on my Mac (Documents, Music, Movies etc) with the relevant folders on the PC so that both systems are exactly the same - which means I need a two-way synch where whichever machine the newest file is on, this appears on both machines with automatic synchronization that is perhaps scheduled (so if I update a file on my laptop, the synch will put this updated file on the desktop and vice versa : whichever is newest).
If anyone can recommend an OS X or Windows piece of software that will do this please let me know! Could even be done through Parallels possibly if both machines have to use the Windows OS.
Many thanks for your help in advance =)A simple solution is to use either a USB flash drive or an external USB hard drive to use as the intermediary. A flash drive would be easy to use depending upon how much data needs to be transferred. Format the drive FAT32 so it can be used on both platforms. On the Mac you could use most any backup utility that can perform incremental backups, and surely there are similar utilities for Windows. Or, you could just drag and drop the files.
If you have a home network, then it would be feasible to use file sharing to move data back and forth between the two machines. See the following:
Mac OS X 10.5 Help- Setting up a Mac computer to share files with Windows users;
Mac OS X 10.5 Help- Setting up a Windows computer to share files with Mac users.
There are dozens of Mac utilities for syncing/backup that could be used. I would suggest Synchronize! Pro X or Synk as possible candidates, but you can find many others. Demos can be found at VersionTracker or MacUpdate. -
Debugging Deserialization Errors Between AIR and BlazeDS on ColdFusion using ORM
Now that I am using CF + ORM for most of my Flex and AIR projects, I've had a much more difficult time with the deserialization of objects from AS to CF. The errors thrown by BlazeDS are not helpful at all, and not indicative of the true issue. cfgatewayadapter.jar is a closed source, and make it even more difficult, because it is the culprit in these issues. These issues can sometimes take a full day or two to resolve because the only way I've seen to debug is to start removing code line by line until the thing works. Huge waste of time.
The problem stems from the fact that during deserlization CF barfs when something doesnt match. Instead of throwing a useful error, it proclaims the CFC doesnt exist serverside. The developer then has to go through each componenty property-by-property to try to determine where the problem is.
What we need is something more specific to what the actual problem is. I've not found an adequate way to debug this, and it's causing me to seriously considering changing the backend to Groovy + Granite so I can get the control I need. Really, Adobe just needs to open up the source on cfgatewayadapter or put some time into refining it so that it throws accurate errors.
Examing the error below, one would think that the CFC does not exist. However, if you run the same examples from CFML and pass it an instance of StreamProvider it works fine.
[BlazeDS]Error deserializing client message.
coldfusion.runtime.CfJspPage$NoSuchTemplateException: Could not find the ColdFusion component or interface StreamProvider.
at coldfusion.flash.messaging.io.ColdFusionPropertyProxy.createInvokable(ColdFusionPropertyP roxy.java:132)
at coldfusion.flash.messaging.io.ColdFusionPropertyProxy.createInstance(ColdFusionPropertyPr oxy.java:93)
at coldfusion.flash.messaging.io.amf.CFAMF3Input.cfreadScriptObject(CFAMF3Input.java:524)
at coldfusion.flash.messaging.io.amf.CFAMF3Input.readScriptObject(CFAMF3Input.java:250)
at coldfusion.flash.messaging.io.amf.CFAMF3Input.cfreadObjectValue(CFAMF3Input.java:138)
at coldfusion.flash.messaging.io.amf.CFAMF3Input.cfreadObject(CFAMF3Input.java:88)
at coldfusion.flash.messaging.io.amf.CFAMF3Input.cfreadJavaArray(CFAMF3Input.java:748)
at coldfusion.flash.messaging.io.amf.CFAMF3Input.cfreadBodyAsJavaArray(CFAMF3Input.java:110)
at coldfusion.flash.messaging.io.amf.CFAMF3Input.cfreadBodyAsJavaArray(CFAMF3Input.java:102)
at coldfusion.flash.messaging.io.amf.CFAMF3Input.readScriptObjectInternal(CFAMF3Input.java:3 95)
at coldfusion.flash.messaging.io.amf.CFAMF3Input.readScriptObject(CFAMF3Input.java:246)
at flex.messaging.io.amf.Amf3Input.readObjectValue(Amf3Input.java:152)
at flex.messaging.io.amf.Amf3Input.readObject(Amf3Input.java:130)
at flex.messaging.io.amf.Amf0Input.readObjectValue(Amf0Input.java:123)
at flex.messaging.io.amf.Amf0Input.readArrayValue(Amf0Input.java:359)
at flex.messaging.io.amf.Amf0Input.readObjectValue(Amf0Input.java:127)
at flex.messaging.io.amf.Amf0Input.readObject(Amf0Input.java:94)
at flex.messaging.io.amf.AmfMessageDeserializer.readObject(AmfMessageDeserializer.java:227)
at flex.messaging.io.amf.AmfMessageDeserializer.readBody(AmfMessageDeserializer.java:206)
at flex.messaging.io.amf.AmfMessageDeserializer.readMessage(AmfMessageDeserializer.java:126)
at flex.messaging.endpoints.amf.SerializationFilter.invoke(SerializationFilter.java:145)
at flex.messaging.endpoints.BaseHTTPEndpoint.service(BaseHTTPEndpoint.java:291)
at coldfusion.flash.messaging.CFAMFEndPoint.service(CFAMFEndPoint.java:295)
at flex.messaging.MessageBrokerServlet.service(MessageBrokerServlet.java:353)
at coldfusion.flex.ColdFusionMessageBrokerServlet.service(ColdFusionMessageBrokerServlet.jav a:114)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at coldfusion.bootstrap.BootstrapServlet.service(BootstrapServlet.java:89)
at jrun.servlet.FilterChain.doFilter(FilterChain.java:86)
at coldfusion.filter.FlashRequestControlFilter.doFilter(FlashRequestControlFilter.java:71)
at coldfusion.bootstrap.BootstrapFilter.doFilter(BootstrapFilter.java:46)
at jrun.servlet.FilterChain.doFilter(FilterChain.java:94)
at jrun.servlet.FilterChain.service(FilterChain.java:101)
at jrun.servlet.ServletInvoker.invoke(ServletInvoker.java:106)
at jrun.servlet.JRunInvokerChain.invokeNext(JRunInvokerChain.java:42)
at jrun.servlet.JRunRequestDispatcher.invoke(JRunRequestDispatcher.java:286)
at jrun.servlet.ServletEngineService.dispatch(ServletEngineService.java:543)
at jrun.servlet.jrpp.JRunProxyService.invokeRunnable(JRunProxyService.java:203)
at jrunx.scheduler.ThreadPool$DownstreamMetrics.invokeRunnable(ThreadPool.java:320)
at jrunx.scheduler.ThreadPool$ThreadThrottle.invokeRunnable(ThreadPool.java:428)
at jrunx.scheduler.ThreadPool$UpstreamMetrics.invokeRunnable(ThreadPool.java:266)
at jrunx.scheduler.WorkerThread.run(WorkerThread.java:66)
[BlazeDS]Deserializing AMF/HTTP request
Version: 3
(Message #0 targetURI=null, responseURI=/3)
(Array #0)
[0] = (Typed Object #0 'flex.messaging.messages.RemotingMessage')
source = "com.mediaslurp.remoting.ProviderServiceProxy"
operation = "savePendingProvider"
timeToLive = 0
body = (Array #1)
[0] =
[BlazeDS]Serializing AMF/HTTP response
Version: 3
(Message #0 targetURI=/3/onStatus, responseURI=)
(Typed Object #0 'flex.messaging.messages.ErrorMessage')
headers = (Object #1)
rootCause = (Typed Object #2 'coldfusion.runtime.CfJspPage$NoSuchTemplateException')
rootCause = null
message = "Could not find the ColdFusion component or interface StreamProvider."
localizedMessage = "Could not find the ColdFusion component or interface StreamProvider."
detail = "Ensure that the name is correct and that the component or interface exists."
cause = null
missingFileName = "StreamProvider"
type = "Application"
body = null
correlationId = null
faultDetail = null
faultString = "Error deserializing client message."
clientId = null
timeToLive = 0.0
destination = null
timestamp = 1.295530026739E12
extendedData = null
faultCode = "Client.Packet.Encoding"
messageId = "6C6E6657-430C-12E6-8B58-E33F7A6D59DC"does MySQL work by itself? did you try connecting to your
databases with
phpMyAdmin or alike?
also, make sure you do not have several
mysql-connector-xxxxxx.***.bin
(whatever their names are, you know, the jdbc driver files)
of different
versions - make sure there is only ONE, preferably the latest
one,
anywhere on your server. remove any other ones.
if i remember correctly, the exception you get in the error
is usually
caused by incorrect/old mysql connector drivers...
Azadi Saryev
Sabai-dee.com
Vientiane, Laos
http://www.sabai-dee.com -
Connection Error between ITS and SAP: R/3 system
Dear All,
Recently we have migrated our Backend SAP: R/3 Servers to AIX/Oracle platform. The server landscape is running on two application servers and one central instance with load balancing.
We have changed all RFC destinations from the SAP:R/3 and ITS side and tested the connection.
We are not able to login to backend SAP:R/3 server through ITS.
The following error appears
"Fatal Error!
The ITS failed to handle this request
The HTMLBusiness interpreter failed to interpret the template.
The internal error message is:
0x2101: Interpreter: The specified input file does not exist."
What other changes from ITS side we have to look into or check?
Regards
saikat180965Hi saikat180965,
Might be the problem is being caused by missing templates. Please have a look in the ITS traces to get more information about the missing file.
Regards,
Dieter -
Replication Error between DC and PDC after a reboot.
Hi,
We have a very small server environment and having one DC and one ADC. Last week ADC got a sudden restart. After booting it shown one service failed error. Since then the ADC is not replicating with DC. Giving below the diagnosis
results of Dcdiag and FSMO check.
Domain Controller Diagnosis
Performing initial setup:
Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site-Name\DC
Starting test: Connectivity
......................... DC passed test Connectivity
Doing primary tests
Testing server: Default-First-Site-Name\DC
DNS Tests are running and not hung. Please wait a few minutes...
Running partition tests on : ForestDnsZones
Running partition tests on : DomainDnsZones
Running partition tests on : Schema
Running partition tests on : Configuration
Running partition tests on : bannaridc
Running enterprise tests on : bannaridc.com
Starting test: DNS
......................... bannaridc.com passed test DNS
Domain Controller Diagnosis
Performing initial setup:
* Verifying that the local machine backupdc, is a DC.
* Connecting to directory service on server backupdc.
* Collecting site info.
* Identifying all servers.
* Identifying all NC cross-refs.
* Found 2 DC(s). Testing 1 of them.
Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site-Name\BACKUPDC
Starting test: Connectivity
* Active Directory LDAP Services Check
* Active Directory RPC Services Check
......................... BACKUPDC passed test Connectivity
Doing primary tests
Testing server: Default-First-Site-Name\BACKUPDC
Starting test: Replications
* Replications Check
[Replications Check,BACKUPDC] A recent replication attempt failed:
From DC to BACKUPDC
Naming Context: DC=ForestDnsZones,DC=bannaridc,DC=com
The replication generated an error (1256):
The remote system is not available. For information about network troubleshooting, see Windows Help.
The failure occurred at 2014-05-15 12:29:41.
The last success occurred at 2014-05-12 09:23:27.
76 failures have occurred since the last success.
REPLICATION LATENCY WARNING
ERROR: Expected notification link is missing.
Source DC
Replication of new changes along this path will be delayed.
This problem should self-correct on the next periodic sync.
[Replications Check,BACKUPDC] A recent replication attempt failed:
From DC to BACKUPDC
Naming Context: DC=DomainDnsZones,DC=bannaridc,DC=com
The replication generated an error (1256):
The remote system is not available. For information about network troubleshooting, see Windows Help.
The failure occurred at 2014-05-15 12:29:41.
The last success occurred at 2014-05-12 09:33:40.
76 failures have occurred since the last success.
REPLICATION LATENCY WARNING
ERROR: Expected notification link is missing.
Source DC
Replication of new changes along this path will be delayed.
This problem should self-correct on the next periodic sync.
[Replications Check,BACKUPDC] A recent replication attempt failed:
From DC to BACKUPDC
Naming Context: CN=Schema,CN=Configuration,DC=bannaridc,DC=com
The replication generated an error (5):
Access is denied.
The failure occurred at 2014-05-15 12:29:41.
The last success occurred at 2014-05-12 09:23:26.
76 failures have occurred since the last success.
[Replications Check,BACKUPDC] A recent replication attempt failed:
From DC to BACKUPDC
Naming Context: CN=Configuration,DC=bannaridc,DC=com
The replication generated an error (5):
Access is denied.
The failure occurred at 2014-05-15 12:29:41.
The last success occurred at 2014-05-12 09:23:26.
76 failures have occurred since the last success.
REPLICATION LATENCY WARNING
ERROR: Expected notification link is missing.
Source DC
Replication of new changes along this path will be delayed.
This problem should self-correct on the next periodic sync.
[Replications Check,BACKUPDC] A recent replication attempt failed:
From DC to BACKUPDC
Naming Context: DC=bannaridc,DC=com
The replication generated an error (5):
Access is denied.
The failure occurred at 2014-05-15 12:29:42.
The last success occurred at 2014-05-12 09:42:25.
95 failures have occurred since the last success.
REPLICATION LATENCY WARNING
ERROR: Expected notification link is missing.
Source DC
Replication of new changes along this path will be delayed.
This problem should self-correct on the next periodic sync.
* Replication Latency Check
REPLICATION-RECEIVED LATENCY WARNING
BACKUPDC: Current time is 2014-05-15 13:24:11.
DC=ForestDnsZones,DC=bannaridc,DC=com
Last replication recieved from DC at 2014-05-12 09:23:27.
Latency information for 2 entries in the vector were ignored.
2 were retired Invocations. 0 were either: read-only replicas and are not verifiably latent, or dc's no longer replicating this nc. 0 had no latency information (Win2K DC).
DC=DomainDnsZones,DC=bannaridc,DC=com
Last replication recieved from DC at 2014-05-12 09:33:40.
Latency information for 2 entries in the vector were ignored.
2 were retired Invocations. 0 were either: read-only replicas and are not verifiably latent, or dc's no longer replicating this nc. 0 had no latency information (Win2K DC).
CN=Schema,CN=Configuration,DC=bannaridc,DC=com
Last replication recieved from DC at 2014-05-12 09:23:26.
Latency information for 2 entries in the vector were ignored.
2 were retired Invocations. 0 were either: read-only replicas and are not verifiably latent, or dc's no longer replicating this nc. 0 had no latency information (Win2K DC).
CN=Configuration,DC=bannaridc,DC=com
Last replication recieved from DC at 2014-05-12 09:23:26.
Latency information for 2 entries in the vector were ignored.
2 were retired Invocations. 0 were either: read-only replicas and are not verifiably latent, or dc's no longer replicating this nc. 0 had no latency information (Win2K DC).
DC=bannaridc,DC=com
Last replication recieved from DC at 2014-05-12 09:42:25.
Latency information for 2 entries in the vector were ignored.
2 were retired Invocations. 0 were either: read-only replicas and are not verifiably latent, or dc's no longer replicating this nc. 0 had no latency information (Win2K DC).
* Replication Site Latency Check
......................... BACKUPDC passed test Replications
Test omitted by user request: Topology
Test omitted by user request: CutoffServers
Starting test: NCSecDesc
* Security Permissions check for all NC's on DC BACKUPDC.
* Security Permissions Check for
DC=ForestDnsZones,DC=bannaridc,DC=com
(NDNC,Version 2)
* Security Permissions Check for
DC=DomainDnsZones,DC=bannaridc,DC=com
(NDNC,Version 2)
* Security Permissions Check for
CN=Schema,CN=Configuration,DC=bannaridc,DC=com
(Schema,Version 2)
* Security Permissions Check for
CN=Configuration,DC=bannaridc,DC=com
(Configuration,Version 2)
* Security Permissions Check for
DC=bannaridc,DC=com
(Domain,Version 2)
......................... BACKUPDC passed test NCSecDesc
Starting test: NetLogons
* Network Logons Privileges Check
Verified share \\BACKUPDC\netlogon
Verified share \\BACKUPDC\sysvol
......................... BACKUPDC passed test NetLogons
Starting test: Advertising
The DC BACKUPDC is advertising itself as a DC and having a DS.
The DC BACKUPDC is advertising as an LDAP server
The DC BACKUPDC is advertising as having a writeable directory
The DC BACKUPDC is advertising as a Key Distribution Center
Warning: BACKUPDC is not advertising as a time server.
......................... BACKUPDC failed test Advertising
Starting test: KnowsOfRoleHolders
Role Schema Owner = CN=NTDS Settings,CN=DC,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=bannaridc,DC=com
Role Domain Owner = CN=NTDS Settings,CN=DC,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=bannaridc,DC=com
Role PDC Owner = CN=NTDS Settings,CN=DC,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=bannaridc,DC=com
Role Rid Owner = CN=NTDS Settings,CN=DC,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=bannaridc,DC=com
Role Infrastructure Update Owner = CN=NTDS Settings,CN=DC,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=bannaridc,DC=com
......................... BACKUPDC passed test KnowsOfRoleHolders
Starting test: RidManager
* Available RID Pool for the Domain is 3107 to 1073741823
* DC.bannaridc.com is the RID Master
* DsBind with RID Master was successful
* rIDAllocationPool is 2607 to 3106
* rIDPreviousAllocationPool is 2607 to 3106
* rIDNextRID: 2771
......................... BACKUPDC passed test RidManager
Starting test: MachineAccount
Checking machine account for DC BACKUPDC on DC BACKUPDC.
* SPN found :LDAP/backupdc.bannaridc.com/bannaridc.com
* SPN found :LDAP/backupdc.bannaridc.com
* SPN found :LDAP/BACKUPDC
* SPN found :LDAP/backupdc.bannaridc.com/BANNARIDC
* SPN found :LDAP/bcbf105f-e755-4c24-b846-01d447834480._msdcs.bannaridc.com
* SPN found :E3514235-4B06-11D1-AB04-00C04FC2DCD2/bcbf105f-e755-4c24-b846-01d447834480/bannaridc.com
* SPN found :HOST/backupdc.bannaridc.com/bannaridc.com
* SPN found :HOST/backupdc.bannaridc.com
* SPN found :HOST/BACKUPDC
* SPN found :HOST/backupdc.bannaridc.com/BANNARIDC
* SPN found :GC/backupdc.bannaridc.com/bannaridc.com
......................... BACKUPDC passed test MachineAccount
Starting test: Services
* Checking Service: Dnscache
* Checking Service: NtFrs
* Checking Service: IsmServ
* Checking Service: kdc
* Checking Service: SamSs
* Checking Service: LanmanServer
* Checking Service: LanmanWorkstation
* Checking Service: RpcSs
* Checking Service: w32time
* Checking Service: NETLOGON
......................... BACKUPDC passed test Services
Test omitted by user request: OutboundSecureChannels
Starting test: ObjectsReplicated
BACKUPDC is in domain DC=bannaridc,DC=com
Checking for CN=BACKUPDC,OU=Domain Controllers,DC=bannaridc,DC=com in domain DC=bannaridc,DC=com on 1 servers
Object is up-to-date on all servers.
Checking for CN=NTDS Settings,CN=BACKUPDC,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=bannaridc,DC=com in domain CN=Configuration,DC=bannaridc,DC=com on 1 servers
Object is up-to-date on all servers.
......................... BACKUPDC passed test ObjectsReplicated
Starting test: frssysvol
* The File Replication Service SYSVOL ready test
File Replication Service's SYSVOL is ready
......................... BACKUPDC passed test frssysvol
Starting test: frsevent
* The File Replication Service Event log test
......................... BACKUPDC passed test frsevent
Starting test: kccevent
* The KCC Event log test
Found no KCC errors in Directory Service Event log in the last 15 minutes.
......................... BACKUPDC passed test kccevent
Starting test: systemlog
* The System Event log test
An Error Event occured. EventID: 0xC25A001D
Time Generated: 05/15/2014 12:30:20
(Event String could not be retrieved)
An Error Event occured. EventID: 0xC25A001D
Time Generated: 05/15/2014 12:49:04
(Event String could not be retrieved)
An Error Event occured. EventID: 0x40000004
Time Generated: 05/15/2014 12:53:20
Event String: The kerberos client received a
KRB_AP_ERR_MODIFIED error from the server
host/backupdc.bannaridc.com. The target name
used was
LDAP/bcbf105f-e755-4c24-b846-01d447834480._msdcs.bannaridc.com.
This indicates that the password used to encrypt
the kerberos service ticket is different than
that on the target server. Commonly, this is due
to identically named machine accounts in the
target realm (BANNARIDC.COM), and the client
realm. Please contact your system
administrator.
An Error Event occured. EventID: 0xC25A001D
Time Generated: 05/15/2014 13:12:19
(Event String could not be retrieved)
......................... BACKUPDC failed test systemlog
Test omitted by user request: VerifyReplicas
Starting test: VerifyReferences
The system object reference (serverReference)
CN=BACKUPDC,OU=Domain Controllers,DC=bannaridc,DC=com and backlink on
CN=BACKUPDC,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=bannaridc,DC=com
are correct.
The system object reference (frsComputerReferenceBL)
CN=BACKUPDC,CN=Domain System Volume (SYSVOL share),CN=File Replication Service,CN=System,DC=bannaridc,DC=com
and backlink on CN=BACKUPDC,OU=Domain Controllers,DC=bannaridc,DC=com
are correct.
The system object reference (serverReferenceBL)
CN=BACKUPDC,CN=Domain System Volume (SYSVOL share),CN=File Replication Service,CN=System,DC=bannaridc,DC=com
and backlink on
CN=NTDS Settings,CN=BACKUPDC,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=bannaridc,DC=com
are correct.
......................... BACKUPDC passed test VerifyReferences
Test omitted by user request: VerifyEnterpriseReferences
Test omitted by user request: CheckSecurityError
Running partition tests on : ForestDnsZones
Starting test: CrossRefValidation
......................... ForestDnsZones passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Running partition tests on : DomainDnsZones
Starting test: CrossRefValidation
......................... DomainDnsZones passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Running partition tests on : Schema
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Running partition tests on : Configuration
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Running partition tests on : bannaridc
Starting test: CrossRefValidation
......................... bannaridc passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... bannaridc passed test CheckSDRefDom
Running enterprise tests on : bannaridc.com
Starting test: Intersite
Skipping site Default-First-Site-Name, this site is outside the scope
provided by the command line arguments provided.
......................... bannaridc.com passed test Intersite
Starting test: FsmoCheck
GC Name: \\DC.bannaridc.com
Locator Flags: 0xe00003fd
PDC Name: \\DC.bannaridc.com
Locator Flags: 0xe00003fd
Time Server Name: \\DC.bannaridc.com
Locator Flags: 0xe00003fd
Preferred Time Server Name: \\DC.bannaridc.com
Locator Flags: 0xe00003fd
KDC Name: \\backupdc.bannaridc.com
Locator Flags: 0xe00001b8
......................... bannaridc.com passed test FsmoCheck
Test omitted by user request: DNS
Test omitted by user request: DNS
Please help me to resolve this issue.
Regards,
surenHi suren,
Error 1256 is logged as the replication status per partition as a result of the destination DC cancelling the sync request from the source DC due to a connectivity failure previously encountered.
Please refer to the articles below to troubleshoot the issue:
Troubleshooting AD Replication error 1256: The remote system is not available.
http://support.microsoft.com/kb/2200187
Troubleshooting AD Replication error 5: Access is denied
http://support.microsoft.com/kb/2002013
Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
Pb of input/output error between iPod and my PBG4
Hi
I have a iPod Nano 2Go and I get all of the problems listed here : wether I try to restore or use the Disk mode, nothing worked ;
all that I could get was a message of error : one saying "1418 error" and other saying "input output error". I tried everything
all I only did was disconnect the ipod when I didn't have to do it.
I have this ipod since last month, and I am really disapointed of that problem
the worst is that Apple doesn't seem to care about it.
Is anyone getting any idea about that...???
Thanks
Kriss / F.GuianaI suggest that take a read the following first, and find a PC connect your iPod with it and follow the instruction
http://discussions.apple.com/thread.jspa?threadID=640556&tstart=0 -
Errors between Mac and Windows Word Users
I am trying to exchange the same Word document with a Windows user that has the newest version of Word.
I use Word 2008 for the Mac. When my Windows Word colleague sends me a document, and I open it with Mac Word 2008, it has @ symbols, A's and = signs that should not be there.
I suspect that these might be some formatting tricks the writer is using (but not sure). My Windows colleague is willing to not use the offending functions, but I don't know what to ask him to not to do.It is sent as a .docx The sender is using Windows XP and Word 2003. I have Mac OS 10.5.8 and Mac word 2008.
He sends me: Test
I get: ATest@
Most of the sentences in the document are fine but there are many errors nevertheless. The errors are more likely where parentheses or underlines are used.
Some errors occur where no parentheses or underlines are used. -
Band width error between Macbook and Macbook Pro
My sister has a powermac g4, I have a macbook (1st release). We use video ichat at least one each fortnight with no problems (after changing the QT, ichat and firewall settings as advised on this site).
Last week she upgraded to a macbook pro. We ran through the quicktime settings, the ichat settings and the firewall setting just as we did before. Unfortunately we cannot connect with video or audio. We just get the 'not enough bandwidth error'.
Bandwidth is not a problem quite clearly.
Any further advice would be appreciated.Hi Jamie,
Ok So the System Preferences > Quicktime is done on the new computer.
The Bandwidth Limit in iChat is set to NONE.
The Mac firewall matches the old computer settings.
That leaves whether or not the modem is using Port Forwarding and if she still has the other computer connected and their relevant IP addresses.
Can you confirm whether her modem is using Port Forwarding and what IP it is pointing to ?
Also I see nothing to suggest in your post that it has anything to do with Airport devices or their updates (being from Amsterdam, Jan must be flying on his own again )
12:41 PM Saturday; January 27, 2007
Maybe you are looking for
-
Can't install Snow Leopard on MBP
Hi Community! Struggling with installing SL on my old MBP. I have family license and have installed SL on my iMac, no problem. I am now trying to install on my MBP. Initially the install disk loaded fine and but I didn't have enough memory. I did som
-
Damsel In Distress: Embedding Sound Clips in Fillable Forms
I embedded sounds (WAV files) in my professional 7.0 pdf with both the sound tool and the button tool. I also customized these with my own icon (JPG and PNG images). PROBLEM: once I open my pdf as a fillable form to add comment boxes, all the sound c
-
Not able to save query. Error messagae: An unexpected object variable or with block variable not set error occurred in WDBRLOG. 1 ERROR(s) are logged. This happened when saving the query.
-
Cannot find symbol class ParseException
I have this in my code how ever DateFormat formatter = new SimpleDateFormat("ddMMyyyy"); dDateStamp = (Date)formatter.parse(dateStamp); When I pass in say dateStamp=safsadssad sa; I get an error which is fine. I can not seem to catch this error with
-
Can i use safari with a windows 7 starter laptop?
Can I use Safari on a laptop running Windows 7 Starter?