Synchronize HU number with SU number

I'm trying to figure out the appropriate way to sync the HU number with the SU number. When I post HU managed stock into the warehouse, I want the SU number to match the HU number.
The notes say "If HUM is active in your system (which it is), all stocks within the WMS are managed in storage units. These storage units are created with the same number as the handling unit. Numbers are assigned in this case using the handling units and not using storage unit management. Therefore, in this case you do not need to set up number assignment for storage unit management. SAP recommends only activating length conversion for storage unit numbers.
If I understand this correctly, if I do not define and assign a storage unit number range, this will happen automatically? Currently, I have an SU number range defined and all SUs are being posted into the warehouse using the next available number in this SU number range.
Your help is greatly appreciated!

Hi,
As to synchronize HU number with SU number, If you use handling unit management in Warehouse Management, you must activate storage unit management for all storage types in which you want to
store handling units. During the putaway, the system creates a storage unit for each handling unit of the transfer orders reference document. This storage unit has the same identification number as its "handling unit sister". When there are nested handling units, the storage unit corresponds to the outer-most handling unit. When partial quantities are picked from such multi-level handling units, the system displays a screen asking you for the lower-level handling unit for the pick or complete stock pick.
The numbering of the storage units is controlled by the number assignment parameters that are set for the handling units during handling unit management and not by the number range(s) of Storage Unit Management. You must therefore activate the storage unit number length conversion in Storage Unit Management Customizing. You must use the same number of signs that is used in the identification numbers for the handling units. The setting applies to all clients (menu path in the Implementation Guide: Logistics Execution u2192 Warehouse Management u2192 Storage Units u2192 Master Data u2192 Define Number Ranges u2192 Conversion exit for storage unit number).
Good luck
Z.T

Similar Messages

Batch Number with Box number

Hello SAP Experts,
My Client has a unique requirement, they want system to track Batch number with Box number.
For Example if Batch number for incomming material is 123456, and if the entire quantity comes in 3 boxes, then the system should track the quantity as 123456/1 , 123456/2 and 123456/3.
Moreover, client wants to issue the materials box wise.
Is there any standard way of capturing this requirement.
Reply is awaited.
Regards
Prabhjot Singh

Hello,
Is there any way, by which I can assign Internal number ranges to the Batches in this scenario.
I have also tried to explore Handling unit management but in that case also we need to pack the material inside, but in my client's scenario they get the box from vendor and store it as it is.
Looking for positive solution.
Regards
Prabhjot Singh

Display material Number with Serialization Number

Hi,
I have a materai with serialization and spilt valuation.
If i wish to display particular material number with serial numbers under oner valuation type, which T code I need to use?
Suppose under one valuation type C1 there are 10 materials, numbered with serial numbers, E.g. Material P1 with serial numbers 1 to 10 under Valuation type C1.
I wish to display this list of serial numbers under that valuation type.
Thnaks & Regards,
Kedar

Check IQ 09
<i><b>U have to develop report for the details u want</i>
Material -env.sr no -. Check

Link Serial Number With Batch Number

Hi Gurus,
I need to link the material serial number with the batch number.
This link needs to be created in advance of the GRN.
Then at the time of goods receipt the processor can select the serial numbers relevent to specific batch number.
Please advice.
Thanks in advance.
NalindaR

while config the serial number profile check if batch number field is there

Sales order number with idoc number

experts
the idoc is generated and posted the sales order and given the idoc number.
how to get the sales order data for this idoc .i have seen the table edidd,edid4etc but no use.
If atleast i get the sales order number with this idoc then i can get the sales order details ie kunnr, matnr,menge etc in vbak table.
please tell me where to get the data of the idoc.

thanks Alexander you are always a great help.
in the status table EDIDS four records are created for each idoc.
in this the one with status 53 has the document number and the field name is STAPA2.
is there any function module to get the order number if we give the idoc number?
or any other table or function module which fetches all the data of the order if we give the idoc number.

TO check SO number with Shipment number in VBFA.

Hi,
i have the shipmnt number and want to get the repective SO number in VBFA.
HOw i cn do this.
Regards,
Monty

Dear Monty,
This can be achieved in two steps :
Step 1
From the input of shipment number at the field "Follow on Doc" in VBFA table, you will get outbound delivery document numbers as the preceding docs (with preceding doc category - J, delivery).
Remember one shipment can have multiple delivery documents according to the scenario.
Step 2
Further you can track "sales orders" through these delivery documents via table - VBFA.
To track the sales orders, again input above delivery docs (found at step 1) as at the field "Follow on Doc" in VBFA table, You will then get the respective sales orders associated as preceding documents (with preceding doc category - C, Orders).
Hope this logic helps you.
Good Luck,
Anubhav

Where to find Oracle Retail number with UPC number, version 14.1

have the UPC number, where can I go in RMS to get the Oracle Item #, Description, Retail, Dept, & Class information?
Thank you

Hi Sanjeeta and Arnaud,
Thank you for the referral
I did the following and it turned out to work perfectly.
A) I listed all Adobe programs on the Firewall exception (like I've done with programs like Steam, where I play games), I'm not certain this helped.
D) Delete the OPM.db file:
Close the Creative Cloud application.
Navigate to the OOBE folder.
Windows: [System drive]:\Users\[user name]\AppData\Local\Adobe\OOBE
Mac OS: /Users/[user name]/Library/Application Support/Adobe/OOBE
Delete the opm.db file.
Launch Creative Cloud.
O) Went through step 2 and 3 > Sign in, activation, or connection errors | CS5.5 and later
B) Restarted the computer.
E) Singed into Creative Cloud first, then launched Photoshop and the other programs.
Thank a lot for all your help
Best regards Emil

How to link applicant number with personnel Number

Hii Experts,
We are trying to extract a report which will get the employees who have been relieved from the organisation within 90 days..
Is there any way to findout the applicant number of an employee.Please advice.
Regards,
sai,

Hi Vicky,
since there is 90 day requirement ,i reckon this need to be customised taking PA0000-MASSN,PA0000-STAT2 and begda and enda into consideration and if there is any date specification (PA41) maintained DAR01 -date type maintained.Hiring action start date and seperation action date.
No Worries
KG

Serial number with external number range.

Dear all
pl how to configure the logice for serial number like gbrx123xeao120001here gbr is prefix code which is fixed x is model sufix,e is yaer of mfg 0001 is serialnumber. so now tell me how to generate the aboce said serial number when production order creation.
pl tell me all config and related settings .
thanks and regards
Baswaraj

Hi ,
Please mainatain the external number range for serial number management as
from 01 to 999999999....... and AAAA.....to ZZZZZZZZ.....
While doing goods movment you can use user exit to define serial number as per the customized calculations .
Also you can create seperate Zprogram for goods movement there u can calculate for Serial number and pass it to goods movement BAPI as per your requirement .
Hope this information helpful .
Best regards ,
Chithaanantham

Report for equipment list with asset number

Hi
I want report where i can get equipment number with asset number. I hecked information system. But id din't got

Follow these steps in the IH08 ALV screen (Output)
- Press Ctrl+F8
- In the pop-up, select Asset field from the Right hand side menu (Column Set) and bring it to Left hand side menu (Displyed Columns) by clicking on the arrow towards left.
- Arrange the position of the field Asset next to the Equipment field (as you desire) by upward/downward arrows.
- Press Enter
Now your Asset column is seen at the place you have arranged.
Regards
Jogeswara Rao

Report for equipment with Asset number

Hi
I want report where i can get equipment number with asset number. I hecked information system. But id din't got

Use Transaction IE05 - it is a Standard PM Module report that has Equipment number and Asset Number.

Link between Material Document number & Accounting document number

Hi All,
For material document there is a corresponding accounting document number generated.However this is not the rule in all cases.
Where is the link between the two(Material Document & Accounting Document) ?
In other words i want to list those material documents only, for which accounting documents are generated.
Regards
Piyush Kothari

STEP 1
SAP query way to extract your information.
Create an infoset SQ02 with a single table MKPF. (include key fields in the field group)
Step 2
From Extras
Create an additional field called zawkey (like bkpf-belnr) which will concatenate the MM document number MKPF-MBLNR and MKPF_MJAHR. The sequencing shall be number 1.
You may use this code below and paste also (this needs authorization as well)
data: zzawkey like bkpf-awkey.
clear: zawkey, zzawkey.
concatenate mkpf-mblnr mkpf-mjahr into zzawkey.
zawkey = zzawkey.
Add another field called ACCDOCNO (accounting documnet number) with sequencing number 2 with following code.
data: zaccdocno like bkpf-belnr..
clear: zaccdocno, accdocno.
select belnr from bkpf into zaccdocno where
bukrs = ccode and
GJAHR = MKPF-MJAHR and
awkey = zawkey.
endselect.
accdocno = zaccdocno.
Step 3
Include the additional fields into the field group.
Step 4
Click on the selection tab and create a parameter called ccode with a description Company Code and against
LIKE BKPF-BUKRS
Extras OBLIGATORY
Step 5
Click on the selection tab and create a seelction criteria pdate with a description Posting Date for the field MKPF-BUDAT
Extras OBLIGATORY
Step 6
Save, Generate and assign the infoset to a user group.
Step 6
Create a SQ01 query under the usergroup with all the fields in the infoset. and Execute. Enter a company code and one date of a working day where you expect material transactions.
The result will be all the material documents and their corresponding accounting documents, if available. If you want to see only those material document that do not have corrsponding accounting documnet, then while you are in the selection screen say accounting document number is not equal to blank.

Current Number Status in Number Range

Hi All
Plz tell me the table in which status of Current Number is stored. That always increment in the Number ranges while running related Tcode.
Like i am running a BDC program and for that transaction at the run time i want to compare some number with current Number Status of the Number Range.
How will i do? Thanks in advance.
Regards
Ravi Arora

Hi Ravi,
There are a lot of FM's ( NUMBERRANGE* ) from se37 which can be used to get the information you need.
Check them you might not need to code to get the current number, The FM will do for you.
Regards
VJ

Message with IDOC number, created by LSMW, missing in job log in SM37

Hi gurus,
We have a temporary interface which uses LSMW to create IDOCs and update in SAP. It's used for materials, BOMs and document info records. In LSMW we have defined standard message types MATMAS_BAPI, BOMMAT and DOCUMENT_LOAD for the IDOCs. All these have the same problem.
A background job runs and starts LSMW. In the job log in SM37 I want to see which IDOCs were created. For some reason this is different in my development system and my test system, and as far as I know all settings should be the same. In the test system LSMW creates more message lines in the job log, than it does in the dev system. Message number E0-097 is "IDOC XXXX added", and this is missing in the dev system.
This is what it looks like in the dev system:
Data transfer started for object 'MATMAS' (project 'X', subobject 'Y')             /SAPDMC/LSMW   501    I
Import program executed successfully                                                             /SAPDMC/LSMW   509    I
File 'XXX.lsmw.read' exists                                                                               /SAPDMC/LSMW   502    I
Conversion program executed successfully                                                    /SAPDMC/LSMW   513    I
Data transfer terminated for object 'MATMAS' (project 'X', subproject 'Y')       /SAPDMC/LSMW 516    I
And this is what it looks like in the test system. More information, which is exactly what I want in dev system too:
Data transfer started for object 'MATMAS' (project 'X', subobject 'Y')             /SAPDMC/LSMW   501    I
Import program executed successfully                                                             /SAPDMC/LSMW 509    I
File 'XXX.lsmw.read' exists                                                                               /SAPDMC/LSMW 502    I
Conversion program executed successfully                                                    /SAPDMC/LSMW 513    I
File 'XXX.lsmw.conv' exists                                                                              /SAPDMC/LSMW   502   I
IDoc '0000000002489289' added                                                                      E0                         097   S
File 'XXX.lsmw.conv' transferred for IDoc generation                                      /SAPDMC/LSMW   812   I
Data transfer terminated for object 'MATMAS' (project 'X', subproject 'Y')      /SAPDMC/LSMW   516   I
In both cases the IDOC is created and update works fine.
My only issue is that I can't see the IDOC number in the dev system. I know I can get the IDOC number in WE02, but in this case we have program logic which reads the job log to be able to check IDOC status before sending OK message back to the other side of the interface.
I hope any of you can have an idea how I can update somewhere to get message E0-097 with IDOC number into the log.
Regards,
Lisbeth

Hi Arun,
If you want to show your messages in the job log you have to use the MESSAGE statement. In case you use WRITE statements an output list be created which can be found in the spool (there is an icon to go to the spool directly).
Regards,
John.

Importing CD to Artist folder\Album folder\file with track number and name:

I have a problem then importing my cd’s to my harddisk using iTunes.
On my previous pc I got what I want, Artist folder, Album folder and file with track number and name:
e.g.
D:\My Music\B.B. King\Blues On The Bayou\01 Blues Boys Tune.mp3
D:\My Music\B.B. King\Blues On The Bayou\02 Bad Case Of Love.mp3
D:\My Music\B.B. King\Blues On The Bayou\03 I'll Survive.mp3
But now I get:
D:\My Music\Compilations\Blues On The Bayou\01 Blues Boys Tune.mp3
D:\My Music\ Compilations \02 Bad Case Of Love.mp3
D:\My Music\ Compilations \03 I'll Survive.mp3
In iTunes my settings are Edit -> Preferences -> Advanced: iTunes Music folder: D:\My Music and checkmark in both: “Keep iTunes Music folder organized” and “Copy files to iTunes Music folder when adding to library”.
My version of iTunes is 8.0.1.11
Thanks in advance
Peter

It will depend on the album. Gracenote considers anthologies, a collection of tracks by the same artist taken from different albums, as a compilation. In iTunes the compliation setting should really only be applied to a collection of tracks by different artists.
tt2

Synchronize HU number with SU number

Similar Messages

Maybe you are looking for