Synchronous LED display with digital output

hi,
In the experiment I want to control a relay, so I use the MAX to generate a digital output task and then transfer it to example code in labview as below. How can I amend this code so that when the module ouput 1 there is a synchronous LED display on the front board.
Thanks~~~

Use single sample digital writes inside your loop. Use a shift register to hold the state (T or F) and invert each iteration. Now you can just wire the state wire to a front panel led and be sure that it is sync'd to the digital output.

Similar Messages

Help with DIgital Output Array with 6062E DAQ CARD...

Good morning, folks... I need some help with digital output of the 6062E PCMCIA card... I can output 1 line without problems... I need to control a 4066 with my digital outputs... I am doing this without greater problems... but there's something... I need that when one of my outputs is high, the others become low, unchangeably... so I tried to use an array to control my output and I couldn't do that... some errors showed up... can you help me please? Maybe there's any errors at my software, then I thank you if you help me... the vi is anexed...
Best Regards...
Attachments:
Untitled 3.vi ‏20 KB

See below for one of many methods. Change the "lines" string for your setup.
Also, please explore the Examples that ship with LabVIEW, and read your card's manual.
Richard

24" LED display with MacBook Pro & DVI output

Simple question. Just bought the 24" LED display. then learned that it won't connect to my 18 month old PacBook Pro out of the box. People have suggested many scenarios for solving this seemingly simple problem, but the two leading threads are in conflict.
Some say i need a complete adapter box. others say i can make the connection with a simple MDP-to-DVI connector.
Need more recommendations please. Thanks to all

The simple Mini DisplayPort to DVI adapters are for connecting DVI displays to Mini DisplayPort computers. To connect a Mini DisplayPort display to a DVI computer you need a converter
<http://www.atlona.com/Atlona-DVI-to-Mini-DisplayPort-Converter-p-17859.html>
<http://www.gefen.com/kvm/dproduct.jsp?prod_id=8913>

Trouble with Digital output on Live Value under Windows

I have a soundblaster li've value card in my system using the digital output in win98se and all works fine. I just upgraded to WinXP. The windows drivers worked fine once i switched them to digital output. However, i lost the Creative mixer and wanted it back. I then downloaded your Unipack driver for the Li've card for winXP and lost the digital output even when i toggled to digital output control. I then downloaded the li've value from the Gateway site since they OEM'd the card in my system and the digital is working again. However, they do not provide the Creative mixer. Is there anyway I can get the Creative Mixer to work in XP wiith the li've value card? Thanks
Soundblaster FAQ states:
Some name brand systems shipped with a special Li've! Value card that was made to work with digital speakers. If you system shipped with a Li've! Value and you have digital speakers you will need to use drivers provided by your system manufacturer. If you use the drivers on the Creative website your card will no longer work with your digital speakers.
Boston Acoustic Digital Speakers or Prebuilt System With a Digital Li've! Card
If you have a set of Boston Acoustic digital speakers that came with your system and they are not working with your sound card, make sure you have it connected to the digital out on the card. Also make sure that the digital out is enabled.

I still always get the value 0.0 returned for minA. I
know that the data is being correctly stored because I
have a seperate report frame that displays all values
for all entries.
Any ideas where the flaw is?
Thanks!
Hey, there. It's unlikely that your users are entering negative numbers which are the only numbers that will be less than zero. You need to initialize your minA to be some quite large number.

USB-6009 pulse train generation with digital output....

Hello!
I've bought a new USB NI-Card (USB-6009) and now I'm trying to adopt an old vi that uses traditional DAQ drivers. I wrote that vi for a PCI NI-Card (PCI-6024E), which has two counters to generate two pulse trains simultaneously. Now I've only one counter and that's why I'm searching for a good way to create pulse trains using a digital output! The pulse trains are both ranging between 100 Hz and 100 kHz.
I'm sure somebody has an idea how I can solve the probem in the best way
Kind regards,
Peter

You can't do it with this low cost board. Both digital and analog outputs are software timed only. The analog out is rated at only 150 samples/sec and the digital is about the same. You can't even use one of the counters because it is not a hardware timed counter output. It is an event counter only as an input.

Problem with digital output and microph

Hello! I recently bought a new motherboard MSI K8N SLI Platinum that have onboard Sounblaster Li've 24bit, with coaxial and spdif and also the standard outputs. I ve connected via a fiber optical cable to my amplifier and i checked the digital output only box to the advanced settings on the mixer. I am hearing sound very well from my amplifier but when i connect headphones to with microphone to my soundcard , i don't hear anything at all from my headphones. Also i cannot speak via microphone. If i uncheck the box digital output only i hear sound from my headphones and also i can speak to microphone. Is there some way to have them both enabled? In my previous motherboard i didn't have that problem. I could hear sound from my amplifier with pcm signal and from my headphones and microphone analog at the same time.
Thanks!

Thibaud,
The clue is here: " i take acquisition with one sample on demand."
You are apparently using software timed output. To maintain accurate phasing at 80 Hz you need timing which is accurate to better than 4 milliseconds. This is not likely to occur with a desktop operating system. Sometimes it will be good and other times OS latencies will throw the timing way off.
If your board supports it, use hardware timing. The timebase sources on most boards are far more precise and accurate than software timing.
Lynn

HP Headphone jack with digital output

OK, so HP customer service is officially garbage. Everyone knows that, i just had to get it out of the way before anybody responds "Just ask customer service". I have a HP Pavillion dv6724ca notebook with 2 headphone jacks. I heard that one of them is a digital output jack for 5.1 surround and my sound card specs say that i have digital output capabilites (go DXDIAG.exe - Realtek Digital Output), but I cant get it working. I have a 3.5mm mini TOSLINK to TOSLINK connected, i have enabled my digital output in Realtek HD Audio Manager, i have checked the supported formats in my Realtek Digital Output properties.....but still nothing. Am i missing something?
thanx

I don't think your model HAS the headphone/mini-toslink SPDIF jack, RE: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01443331&cc=us&dlc=en&lc=en&jumpid=reg_R1002_US... . The HDMI port is SUPPOSE to support BOTH digital Video AND Audio... however I BELIEVE that there was/is some problems with the Audio side on some HP models. BUT to be sure however, use the search facility to search on HDMI. If everything is working according to spec (on the PC AND on your >>>TV<<< ), you should ONLY need a single HDMI cable to do what you want ... but I fear you are going to run into problems. Report back your findings.
Good Luck.

Digital stimulus-frequency response: Need to drive with digital output trigger. Using counters for response.

I need to drive stimulus-response with a software driven digital trigger and NI-TIO counter based response. No analog I/O is really relevant, although I have a PCI-6035E multi-function DAQ as part of my gear. I intend to use the analog, but its timing is non-critical and can be software timed.
The real trick is that I want to set the basic timing of the system (in the range of 1 - 50Hz) from the timer0 on the 6035E. This signal needs to be replicated to drive a trigger pulse and to route through RTSI (or a PFI) to trigger frequency counts using the four possible groups of counter/timers on the 6602.
What I need is:
while( enabled )
Repeat at (
software controllable rate = 1-50Hz)
Trigger Sets a PFI line for 10-20us
same trigger sets an RTSI line
- Software Set Delay (usually zero)- stable is more important than the delay time!
Count for software set time on 4 counters
analog samples
Post-process
I want to do this in LabView. I have checked out the Advanced sychronization demos online, but the examples all use analog triggering and buffered digital I/O. This doesn't really address what I need to do.
I have made some failed attempts which relied on software to sync up the trigger and the response frequency acquisition. This is definately flawed. I need to start the counting right after setting the digital output trigger, and stop the count after a fixed interval for frequency calculation.
I am having trouble working through the signal routing to get the timing to trigger off the digital stimulus output pulse.
Any help would be appreciated
Thanks,
Joe

Joe
What are you using the trigger from the 6035E for? I do not know what you mean by, "to trigger frequency countes."
If you are having problems just routing the signal to the 6602, here is a vi that shows you how to route a signal through the RTSI cable to use as the source of a counter.
Brian
Attachments:
Route_RTSI_to_Source.vi ‏67 KB

PID with digital output

Hi,
I have the application.
I do not clear about PID function but, I would like to ask you about my application.
I have a sensor water level and a few motors to control gates
I measure water level and control motor via digital output(using the fieldpoint system)
I would like to hold water level at level, so I use PV indicator and SV control. when I change SV then will control Motor (RW or FW motor).
Can we use how technology to hold water level PV=SV ?.
Please let me know your comments.
Thanks
Nguyen Van Hung

Hi Nguyen,
There are several examples in CVI under Help » Find Examples that may be able to help speed up the development of your PID program (assuming you have purchased the CVI PID Toolkit). These examples can be found by going to Toolkits and Modules » PID and Fuzzy Logic Control » PID. Depending on how familiar you are with PID algorithms, I might suggest that you look at the GeneralPid example first. Additionally, the PID Control Toolkit User Manual t is also a great place to look at the algorithms and the library functions. Finally, in case you aren't aware, you can double click on any function that you find in the Libraries folder located in the bottom left of CVI to open a functions panel which will show all inputs and outputs of a given function. Then, you can right click on any parameter to view details about that or on the function panel (outside an input box) for more information about the function in general.
I hope these resources help you design an algorithm that works well for your situation!
Regards,
Trey C.
Applications Engineer
National Instruments

Using New Apple 27" LED Display with old MacBook Pro (Late 2006) 15"

I've got a MacBook Pro (Model # A1211) Core2Duo 15" 2.16 GHz with only 128 MB of VRAM and a built-in DVI port (I think it is dual-link DVI)
My question is, will the new 27" LED Display work with this machine at its best resolution? If so, what adapter would I need to get it to work?
Thanks!

I don't think the Kanex adapter is the best one to purchase. The information on their website says it will only drive the 27" at 1280 x 720. Although I have not purchased one yet, the ATLONA website http://www.atlona.com/Atlona-Dual-Link-DVI-to-Mini-DisplayPort-Converter-USB-Pow ered.html, claims their Atlona AT-DP400 converter will drive the 27" at its highest resolution of 2560 x 1440. I have read confirmation from some users that this is the case for the DP400.

No Sound Output with Digital Output Mac

Hi There,
I normally use my Blackmagic card for sound output on my Mac with Premiere CS6. I want to work with the digital output on my current project but when I try switching to digital out under Preferences>Audio Hardware the audio still comes out of the Blackmagic card but not the digital audio out on the Mac. I'm testing with the bars and tone in the browser and my timeline sequence. FCP 7 works as expected when digital out is selected, and I know digital out is working properly on my computer.
Any suggestions?
Thanks!
Gerry

OK, sorry it was that I had to switch audio device under plackback.
Perhaps this should be added to the FAQ under No Sound During Playback, which doesn't include the Preferences>Playback as part of the troubleshooting for MAC.
Thanks!
Gerry

Help with Digital Output software

Hey people. I need your help to improve my software. I need to use some digital outputs. The software does this:
- Choose which one battery to monitor
- Activate only one digital output at a time
Ok, I have done this, but I guess it's not the best solution. I've tried to make it a lot of different ways, mainly because I am using the VI's several times and it is not an "optimal code". Well, beyond that, I can't have two digital outputs HIGH at the same time, i mean, I CAN'T have LINE2 and LINE3, for example, at HIGH (true) at the same time.
Does anybody have any idea on how to help me?
Thank you very much!
Attachments:
Medidor Bateria.vi ‏65 KB

Thank you very much, Jeff. I know my solution is not the best, but I need to ensure that only one of my outputs be at HIGH level. I am trying to use the RADIO buttons, and the program is attached here. But there is this problem, that is I repeat all the VI's. Please check this for me, if you can. Thank you very much, your help is very important!
Attachments:
Medidor com Radio.vi ‏28 KB

IPod with digital output?

We all know that the iPod only offers an analog audio output and the quality is limited. It does not matter what you hook it up to, it still sounds just like the analog outputs.
But I just read this products, seems very interesting. Keen to get one (if it proves work - but review available yet)
http://www.sound4sale.com/index.php
The iLink System costs $1,995 !!!!!! may be not worth, I am looking for the iPod Upgrade which costs $199 and I can still connect it with my DAC in digital
By the way, I believe that some of the users may not heard this MSB company before, but I must say that it is a well know audiophile company

A Zune was an Microsoft product that was similar to an iPod. Microsoft terminated producta year or so ago.
Zune - Wikipedia, the free encyclopedia

Seven segment led display with arduino pin configurations

iam new here.. i am trying to dipaly a numbers on led seven segment display. but i dont know how to cinfigure pin numbers with arduino examples...
can anyon eexplain the pin configuration in sevensegment led.

Hi anilkun,
in the linked example you see that picture. It shows all the needed wires to connect Arduino with 7segment LED.
What else do you need?
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

27" LED Display with power issues

I have had some peculiar issues with my ACD since I received it about a month and a half ago. I use it with my new i7 iMac. Specifically, the issue is with the power supply inside the unit (I think). One night about a month ago, I heard a "pop" from behind the ACD, and it went black. I knew that the unit itself was fully powered down as I could get nothing from any of the USB ports (such as charging of my iPod). I swapped power cables with my iMac, and the iMac powered on just fine, so I ruled that out. I then left the unit unplugged, boxed it up, and took it to the Apple Store the day after. To my surprise, it powered up just fine when I got there. Sure enough, it worked again when I brought it back home.
Now, just last night, I switched off the breaker panel to the circuit that had the ACD on it to change a light fixture. When I turned it back on, I powered back up my iMac...and the ACD did not turn on. Same thing: all ports dead, no power at all. Left it unplugged for 2 hours...no results. Then, I left it unplugged over the entire night. When I woke up, plugged it back in , and now it works again.
It seems as if the longer amount of time allows the power supply inside to "reset" somehow or something, but I am at a loss as to if this is some sort of true defect, or a flaw in design. Even the instruction manual recommends leaving the unit unplugged for a while if it fails to power on.
Anyone have similar issues? Anyone able to help me figure out what is going on?

What I do when I have issues that can be tough to replicate is record them with my phone, take the unit to the store, and if it doesn't happen, show them the video.

Synchronous LED display with digital output

Similar Messages

Maybe you are looking for