SYSTEM ERROR - CONFLICT

Hi Admn Experts!
I have installed SAP 4.7 EE with same host name, but its giving system error ( Duplicate name exists) while connected in the same network. But if I change the Host name ( computer Name ) of one system the database instance starts in RED color, and can't modify any program.
How to resolve the issue any ideas please.!!!!
Rewards will be given for any suggestions. 
Thanks in advance,
Sunil

Hello Sunil,
Juan means you need to do central instance installation once more and they do the homogeneous system copy. When installing the central instance you can input a new SID.
However you original question is not very clear. You have not phrased it properly. For example I have installed SAP 4.7 EE with same host name: What do you exactly mean by same host name? .but its giving system error ( Duplicate name exists) while connected in the same network When are you getting this error.
May be if you explain it better you may avoid setting up a new system.
Regards.
Ruchit.

Similar Messages

System error message and application crash - ModName: lvrt.dll Offset: 00080a6a

I'm running into an error message which is proving particularly difficult to debug. After my built application has been running for some time, a windows system error will pop up telling me my application has done something bad and needs to be shut down (and sorry for the inconvenience). Clicking through to the "see what the error report contains" page reveals the issue as being in the lvrt.dll module at offset 0080a6a.
This unfortunately doesn't mean much to me.
On some occasions when I click "Don't Send", another error message pops up informing me there is "Not enough memory available to complete this operation".
The program will typically run between 8 and 24 hours before the error occurs, though I've had it run error-free for upwards of 48.
My program is unfortunately fairly large, and depends on communication with proprietary hardware so can't be uploaded in a functional state. In general terms, the body of the program (which is executing when the error occurs) involves RS-485 serial communication and simultaneous display of data to 7 continuously updating strip charts (producer-consumer design), along with envalope detection and RMS calculations in real time, all of which is multiplied by two parallel channels (around 1Mb/s data rate for each). The data is also buffered and stored in binary files for later review. Binary files are closed and a new one is opened for every 10 minutes of data collection (approx 50MB of data).
There are also about 40 user controls associated with each channel, and are polled periodically (a couple times a second). The crashes occur during over night tests, however, when there is no user input. Globals are used for inter-panel communication, but no global is written to in more than one location (most are read in multiple locations).
I know this is a bit of a shot in the dark here, but does the lvrt.dll error at offset 00080a6a mean anything to anyone? Are there any "typical" causes for a failure in lvrt.dll having to do with prolonged high data rate serial communications? For reference, this has occured on multiple machines, but all the machines it has occured on are identical out-of-the-box laptop models running XP 32. I'm going to try to run an overnight test tonight on the development machine and see if I get any different results (Vista 64 vs Windows XP 32).
I can't say my hopes are high with this one, and I'm gonna continue to comb over the code for any possible conflicts, but any insight would be appreciated.

Claire,
Next time the error message comes up I will take a screenshot of it for you. Unfortunately that may not be until Monday, as tonight is the soonest I'll be able to run another long-term test. The time between failures is the most frustrating part to debug!
There are no errors on compiling or building the application in LabVIEW. My testing has been done mostly on the distribution laptops in application form, with no LabVIEW dev tools installed, Windows XP 32 bit.
The overnight test I attempted on the development machine (within the LabVIEW environment) welcomed me the next morning with a rebooted machine, and so I wasn't able to see an error message (if there was one). Vista 64 on the development machine. Reviewing the data files, I got about 9 hours worth before the crash.
Given the time between failures and the large volume of data I'm passing around, this seems like memory leak type behavior. I'm a bit confused by the fact that it seems to fail in lvrt.dll every time, though. I'm don't know what that indicates, if anything.

Fix sync center's errors/conflicts through server

Hi all,
Our system relies on folder redirection and roaming profile.
I can see some type of errors/conflicts on sync center, such as an error states "cannot access the file because it's being used by another process", a conflict asking delete/keep one/keep both file(s).
The person used to work before me said, he checks every single end user's computer every day for checking those errors/conflicts and resolving.
I wonder is there any place that I can check the status of syncing, and solve it through server instead of checking every computer physically.
Our server is 2012 R2, user computers are win7 or 8.1 pro.
Thank you very much for your answer in advance.

Hi JJay1231,
You can view sync errors on the Sync Results screen in Sync Center. Once you understand what is causing the sync error, you can try to fix it. A sync error usually occurs when
there is a problem with the device, computer, or folder you are trying to sync with, such as a device that is not plugged in or turned on when you try to sync with it. Errors usually block sync from completing. If you have a sync error that you don't fix,
you will probably end up with files that are not in sync, so it's a good idea to try to fix sync errors when they occur.
Resolving sync conflicts: frequently asked questions
http://windows.microsoft.com/en-us/windows-vista/resolving-sync-conflicts-frequently-asked-questions
Troubleshoot sync problems
http://windows.microsoft.com/en-us/windows-vista/troubleshoot-sync-problems
Event ID's 1502 and 1508 User Profile does not load properly on Windows Server 2008 Terminal Server non roaming profiles
https://social.technet.microsoft.com/Forums/windowsserver/en-US/955c99c0-cd7d-4aad-9517-067990008a91/event-ids-1502-and-1508-user-profile-does-not-load-properly-on-windows-server-2008-terminal-server?forum=winserverTS
When you use roaming profile please use the following supported scenario.
Microsoft’s Support Statement Around Replicated User Profile Data
http://blogs.technet.com/b/askds/archive/2010/09/01/microsoft-s-support-statement-around-replicated-user-profile-data.aspx
I’m glad to be of help to you!
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Arabic language input system error curve 9300

i have a blackberry curve 9300 running ios 6. every time i try to write in Arabic, whenever i hit teh space bar, i get a message "imput system error. system is being restarted" is there a solution to this?

Hello!
That error typically means that there is serious corruption in your OS...and a clean OS reload is needed to attempt to cure it.
At the top of each device forum, there should be some "sticky" threads that discuss the OS levels available for many models. If they include your model, then please use those as reference as you proceed. Otherwise, you will have to dig through the official download portal for OS packages for your model:
http://us.blackberry.com/support/downloads/download_sites.jsp
From a PC, you can install any compatible (e.g., for your exact BB Model Number) OS package to a BB via this procedure:
http://supportforums.blackberry.com/t5/BlackBerry-Device-Software/How-To-Reload-Your-Operating-Syste...
Note that while written for "reload" and the Storm, it can be used to upgrade, downgrade, or reload any BB device model -- it all depends on the OS package you download and install to your PC. If that OS package is from a carrier other than the carrier for which your BB was originally manufactured, then delete, on your PC, all copies of VENDOR.XML...there will be at least one, and perhaps 2, and they will be located in or similarly to (it changes based on your Windows version) these folders:
C:\Program Files (x86)\Common Files\Research In Motion\AppLoader
C:\Users\(your Windows UserName)\AppData\Roaming\Research In Motion\BlackBerry\Loader XML
Be sure that you remove, from your PC, any other BB device OS packages as having more than one installed to the PC can cause conflicts with this procedure.
You may also want to investigate the use of BBSAK (bbsak.org) to perform the wipe it is capable of.
You may also want to try this procedure to perhaps narrow down the precise causal item:
Load your OS "bare bones"...if anything is optional, do not install it.
If the behavior presents immediately, then try a different OS with step 1
If the behavior does not immediately present, then run for as long as it takes for you to be sure that the behavior will not present.
Add one thing -- no matter how tempting, just one.
If the behavior does not present immediately, then again run for long enough to be sure it will not have the same problem
Repeat steps 4 and 5 until all things are loaded or the behavior presents
When the behavior presents, you know the culprit...the last thing you loaded.
If the behavior does not re-present, then you know that either step 1 or 2 cured it.
If the behavior presents no matter what, then you likely have a hardware level issue for which no amount of OS or software can cure.
If you are on MAC, you are limited to only your carriers sanctioned OS packages...but can still use any levels that they currently sanction. See this procedure:
KB19915How to perform a clean reload of BlackBerry smartphone application software using BlackBerry Desktop Software
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

MDD FW 400 won't boot OS 9 | System error "Unimplemented Trap" Huh?

Hey guys, I need help with a weird problem. I recently bought a MDD dual 1.25 with 1.5MG RAM, CPU Type:PowerPC G4 (3.3), Boot ROM Version: 4.4.8f2. It came with a single 60 gig drive in it with OS 10.2.6, and it used to boot directly to the OS 9 system folder just fine. I took out that drive, installed it in my old Blue & White POS, gave that to my wife and now have: a seagate 80 gig drive (originally in the B&W), as well as a 160 gig & a 200 Gig.
All three drives have 9.2.2 on their own partitions, as well as on the 2 master drives with OS 10.3.8 & 10.3.6 respectively. I can’t boot directly to 9 from any of them.
The 200 gig drive was the only one of the 3 formatted directly from within the MDD, clean install, with OS9 drivers selected on install.
When I select ANY of the OS9 partitions, even the OS9 system folders on the OSX partitions for that matter, I get:
1. a grey screen (for a little too long)
2. then a happy mac box (and the cursor appears)
3. Then an empty floppy disk icon
4. Then a “?” inside the floppy disk icon
5. finally a system 9 style “bomb box” and:
“sorry, a system error occurred. Unimplemented trap. To temporarily turn off extensions, restart and hold down the shift key” .
There is a restart button. Perhaps I should mention the error dialog is apparently blocking what appears to be the “Welcome to Mac OS 9.1” screen before the icon march.
Maybe that 9.1 means nothing, but I HAVE NO 9.1 system folders on any disks. They are all 9.2.2... Well that part just bugs me.
The issue is that when I click “restart” and hold down the shift key as directed, the same actions above 1 thru 5 happen, and I’m back at the bomb.
The only way out of the cycle is to “option restart”, and all my partitions show up EXCEPT the OS 10.3.8 partition I had begun the process from. Since I have another OSX partition on one of the disks, I can select that and boot to it no problem. I am then able to select the original OSX partition on the “main” drive, and return to square one, where the cycle began. All the OS 9 system folders can be used to “boot” classic mode, and Tech Tool, Disk Warrior, all are run regularly and report minimal issues. The machine works fine, except for this one issue.
So, why is my MDD preventing me from booting directly into OS9? I read somewhere on another thread that the boot ROM is system specific, so that might answer why the drive pulled from the B&W won’t boot to 9, but the new drive was formatted by the MDD disks, and I even tried a reinstall of OS9 to that disk in an attempt to “unstick” the system. All system 9 folders reside on master drives (so slave is not the issue).
But none of the 9.2.2 folders when selected will bring me anywhere but the bomb, apparently “TRYING” to boot OS9.
WHAT am I missing here? Any ideas?
I need my Nine!!
Tom
Mirrored Drive Door G4, B&W G3 POS, broke Beige Tower Mac OS X (10.3.8) ATTO usb card, combo & superdrive, uber music gear
B&W G3, Mirrored Drive Door G4, Beige Tower Mac OS X (10.3.8) Atto USB card, combo drive, super drive

AJ,
Consider me dyslexic about the MDD. I don't know how
to reset the PMU on it. My beige G3 had a button on
the motherboard
there is a button on the motherboard of the G4. Location and color may vary. Usually black or red, mounted on a raised silver or black square...typically about 1/4" square
the B&W had a "programmers button" on the front faceplate
That's also known as an 'interrupt switch' With the appropriate debugger software, programmers could push that button and call up the debugger, which would allow them to trace their code and issue low level commands. Sometimes useful to break out of a crashed program without pulling the plug.
I know what I know from doing & reading and yes I have a
system folder or two that began in a 6320CD Performa
I think that was one of the machines that required a special file to boot - which is the file I cannot recall the name.
If that file still exists in your system folder, then it may be the culprit.
I'm certified dangerous because of knowledge gaps....
Aren't we all?
such as CDEVs are control panels?
CDEV is ControlDEVice, otherwise known as a control panel.
init's are mostly extensions?
Yes.
and what are TSR's?
Terminate and Stay Resident. Actually a DOS term for a program that runs, quits, but remains loaded in memory.
Apple calls them inits.
Many of the icons that appear during the OS9 boot process are functionally TSRs.
Init conflicts usually were the result of two or more of these programs fighting over the same block of ram.
It sound like you're asking me to search the system
folder for some invisible files correct?
No. The files should be visible. Since you can't yet boot to 9 (thus might not be able to get to use startup manager), I gave you the hard way to find and disable them.
Recall the OS9 startup mananager, which allows you to selectively enable and disable startup items? When you use startup manager, active items (with a check) will be in a folder named, for example, Control Panels. Inactive items, those without a check, will be in a folder named Control Panels (disabled)
To activate the startup manager at boot, hold down the spacebar. It should be the first thing to load. You can select OS9 only, none, or selectively tunr items on/off. Startup manager will automatically move items from the active to the disabled folder.
If you know the file names, you can manually move things from one folder to another, (which is the process I described)
All those files load in alphabetical order. Some of those items want to be loaded first, so the file was named with a leading space, period, or similar. ( Adobe type manager, for example)
There are a couple that are named such that they will load before startup manager.
Since your crash is almost immediate, I'm betting it's one of the first to load TSRs thats causing the problem.
The 80 gig resides in the B&W, so you're suggesting,
pulling it, installing it in the MDD & dragging the
system folder from there?
That is one method. Or mount the BW with Target disk mode and copy it across. Or copy the system folder to CD.
or if the machines are networked, copy across the network. Or USB memory stick, depending on the size of the folder.
The object is to get a known working drive with a known working/bootable OS into the new machine. Since I know my machine will not see either the 200 or 160 when boot to 9, and on some machines, 9 will not see anything over 128gb, I suggest getting a known good copy of 9 on a drive physically smaller than 128gb (not a sub 128 gb partition of a much larger drive)
Temporarily disconecting the larger drives has no purpose beyond helping eliminate the complexity during diagnostics and troubleshooting. You know they work as intended, and are not part of the problem.

PCSuite Sync - "System Error"

Recently I have started getting the message "System Error" on my N73 when synchronising with PC Suite. I notice from several posts in this forum that many other people have reported this problem, yet I am not happy with all of the suggested solutions.
I synchronise my N73 with two different PCs, one is Windows 2000 and the other Windows Vista (still waiting for my company to upgrade us to Windows XP!!). This has worked well for a long time, and allows me to have a synchronised calendar at work, home and everywhere I go. (Both PCs use Bluetooth to sync regularly when the phone is in range).
I have not updated either the phone nor any of the PC suite applications, so I can only conclude that the System Error is caused by a corrupt entry in the calendar, contacts or something else that is being synchronised.
*** My request to Nokia is that having reached the point where the synchronisation fails, can you highlight the entry so that it can be resolved by the operator?
I have over 500 contacts and over 6 months of calendar synchronised in my N73, therefore wiping all of the data in the phone is not an option I wish to persue. I can confirm that it is not low on memory and all software is up to date. Like I said, it worked before and I made no system changes.
The error message from PC Sync simply says "PC Sync was not able to send data to the mobile phone."
The problem first started at home, but now I'm getting the message at work too.
If anyone knows any other ways to resolve this, I would be glad to hear.
Regards,
Nigel
Solved!
Go to Solution.

Hi,
If your phone supports create new sync support, click on create new sync settings while at the Finish option you will spanner icon for advance settings of Nokia PC Sync - It will Automatic Sync, Conflict Resolution, Direction and Sync profile. In that Direction is 3rd option.
BTW., which version of pc suite are you using? Which handset are you using? Connectivity BT/IR/USB ??

NiRFSA_ReadPowerSpectrumF64 function call in TestStand 4.5.1 cause system error

I am using TestStand with niRFSA.dll to call the function niRFSA_ReadPowerSpectrumF64. This function will make the NI RFSA takes a spectrum sweep and return an array of amplitudes, as well as a structure that contains the frequencies information. My teststand sequence file is attached. The sequence editor will execute this function call, and actually retrieve correct data from the RFSA, I can see all the data in the Locals variables. The data are correct. However, the sequence editor also throws out system error, with no further details.
See the error window also attached.
Once in a while, the sequence editor will work just fine, executing the same function call without throwing out error, this is less than 10% of the time.
I am using this on Windows 7.
Let me know if you have any insight.
Attachments:
RFSA Sequence.seq ‏7 KB
Capture.JPG ‏33 KB

Hi Doug:
Yes this is what I suspected also. Since the container type was a TS custom type I created to accept the C struct from the instrument. But when the data come back from the dll is a C struct, and there lays the conflict, I think its the packaging layer semantics have some conflict, even though each of the element in the C struct matches the TS type definitions, as I received all that data correctly in TS.
Thanks,
Juswanto

"input system error. the systen is being re-strted"

Hi
I keep on at random times getting the following message "input system error. the systen is being re-strted"
On top of that I also have the issue with the curser jumping about the screen, I have already reinstalled the OS software and had the button replaced so was wondering if anyone had anything else to try?

Hi and Welcome to the Community!
At the top of each device forum, there should be some "sticky" threads that discuss the OS levels available for many models. If they include your model, then please use those as reference as you proceed. Otherwise, you will have to dig through the official download portal for OS packages for your model:
http://us.blackberry.com/support/downloads/download_sites.jsp
From a PC, you can install any compatible (e.g., for your exact BB Model Number) OS package to a BB via this procedure:
http://supportforums.blackberry.com/t5/BlackBerry-Device-Software/How-To-Reload-Your-Operating-Syste...
Note that while written for "reload" and the Storm, it can be used to upgrade, downgrade, or reload any BB device model -- it all depends on the OS package you download and install to your PC. If that OS package is from a carrier other than the carrier for which your BB was originally manufactured, then delete, on your PC, all copies of VENDOR.XML...there will be at least one, and perhaps 2, and they will be located in or similarly to (it changes based on your Windows version) these folders:
C:\Program Files (x86)\Common Files\Research In Motion\AppLoader
C:\Users\(your Windows UserName)\AppData\Roaming\Research In Motion\BlackBerry\Loader XML
Be sure that you remove, from your PC, any other BB device OS packages as having more than one installed to the PC can cause conflicts with this procedure.
You may also want to investigate the use of BBSAK (bbsak.org) to perform the wipe it is capable of.
You may also want to try this procedure to perhaps narrow down the precise causal item:
Load your OS "bare bones"...if anything is optional, do not install it.
If the behavior presents immediately, then try a different OS with step 1
If the behavior does not immediately present, then run for as long as it takes for you to be sure that the behavior will not present.
Add one thing -- no matter how tempting, just one.
If the behavior does not present immediately, then again run for long enough to be sure it will not have the same problem
Repeat steps 4 and 5 until all things are loaded or the behavior presents
When the behavior presents, you know the culprit...the last thing you loaded.
If the behavior does not re-present, then you know that either step 1 or 2 cured it.
If the behavior presents no matter what, then you likely have a hardware level issue for which no amount of OS or software can cure.
If you are on MAC, you are limited to only your carriers sanctioned OS packages...but can still use any levels that they currently sanction. See this procedure:
KB19915How to perform a clean reload of BlackBerry smartphone application software using BlackBerry Desktop Software
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Effectv don't compile. error: conflicting types for 'trunc'

hello all.
i'm full newbie, so please, be kind
I try to install effectv from AUR, but when i try to 'make' - i receive error:
error: conflicting types for 'trunc'
then i download sources and try to compile them - and again receive this error.
Please advice, what should i do to correct this error?
Thank you and sorry for my english.

Please contact the author of the PKGBUILD to have it changed in the AUR. This fixes your issues:
PKGBUILD
# Contributor: Luiz Ribeiro <luizribeiro>
pkgname=effectv
pkgver=0.3.11
pkgrel=1
pkgdesc="EffecTV is a real-time video effector. You can watch TV or video through amazing effectors."
url="http://effectv.sourceforge.net/"
depends=('sdl')
makedepends=('nasm')
conflicts=()
license=
install=
source=('http://jaist.dl.sourceforge.net/sourceforge/effectv/effectv-0.3.11.tar.gz'
'gcc.patch' 'timedist.patch')
md5sums=('71570b71009df0f1ff53e31de6f50cee')
build() {
cd $startdir/src/$pkgname-$pkgver
patch -Np0 < $startdir/src/gcc.patch || return 1
patch -Np0 < $startdir/src/timedist.patch || return 1
sed -i -e 's_/usr/local_/usr_g' config.mk
make || return 1
mkdir -p $startdir/pkg/usr/bin
mkdir -p $startdir/pkg/usr/man/man1
make install INSTALL=/bin/install -c DESTDIR=$startdir/pkg || return 1
gcc.patch : fixes compile problem
--- utils.c.orig 2006-02-14 15:06:17.000000000 +0100
+++ utils.c 2006-08-30 22:47:19.514145536 +0200
@@ -26,7 +26,7 @@
* HSI color system utilities
-static int trunc(double f)
+static int trunc_color(double f)
int i;
@@ -44,9 +44,9 @@
Gv=1+S*sin(H);
Bv=1+S*sin(H+2*M_PI/3);
T=255.999*I/2;
- *r=trunc(Rv*T);
- *g=trunc(Gv*T);
- *b=trunc(Bv*T);
+ *r=trunc_color(Rv*T);
+ *g=trunc_color(Gv*T);
+ *b=trunc_color(Bv*T);
timedist.patch : fixes bug
This is a quick fix for bugs of effectv-0.3.11. TimeDistortion has a border
crossing bug and a buffer uninitializing bug.
Index: effects/timedist.c
===================================================================
--- effects/timedist.c (revision 478)
+++ effects/timedist.c (working copy)
@@ -27,7 +27,16 @@
static int plane;
static int *warptime[2];
static int warptimeFrame;
+static int bgIsSet;
+static int setBackground(RGB32 *src)
+{
+ image_bgset_y(src);
+ bgIsSet = 1;
+
+ return 0;
+}
+
effect *timeDistortionRegister(void)
effect *entry;
@@ -70,6 +79,7 @@
plane = 0;
image_set_threshold_y(MAGIC_THRESHOLD);
+ bgIsSet = 0;
state = 1;
return 0;
@@ -94,6 +104,9 @@
int *p, *q;
memcpy(planetable[plane], src, PIXEL_SIZE * video_area);
+ if(!bgIsSet) {
+ setBackground(src);
+ }
diff = image_bgsubtract_update_y(src);
p = warptime[warptimeFrame ] + video_width + 1;
@@ -109,7 +122,7 @@
q += 2;
- q = warptime[warptimeFrame ^ 1] + video_width + 1;
+ q = warptime[warptimeFrame ^ 1];
for(i=0; i<video_area; i++) {
if(*diff++) {
*q = PLANES - 1;

'System.capabilities', conflicts

I keep on getting this error message. If I publish the file
twice, it is ok.
..\Local Settings\Application Data\Macromedia\Flash
8\en\Configuration\Classes\FP8\System\capabilities.as: Line 7: The
name of this class, 'System.capabilities', conflicts with the name
of another class that was loaded, 'System'.
running Flash 8 on windows, although this occurs on the Mac
too. Any help would be appreciated. I googled for this problem and
found another unsolved case:
http://www.actionscript.org/forums/archive/index.php3/t-86822.html

thanks for confirming the problem. so frustrating, cant
explain to my boss why or how...
im wondering though, do you also build using Flash 8 but with
the publish setting to Flash 7?

'System Error' status at Message Monitoring( HTTP to FILE )

I have created a scenario HTTP to FTP. I sent message to XI server using the HTTP Client.
After sending the message I am getting the response at browser.
Result:
http-Status: 200 Message accepted
Payload:
But when I look in to the Message monitoring at RWB, I am getting the message status as
System error. while going to the details i can see below error category.
Error Category MAPPING
Error Code EXCEPTION_DURING_EXECUTE
(Is the password different for port 50000 and 8000)
Please help me to solve this issue.
Thanks in Advance,
John

This is the trace message that I got for this error
<Trace level="1" type="T">com.sap.aii.utilxi.misc.api.BaseRuntimeException: Fatal Error: com.sap.engine.lib.xml.parser.ParserException: XML Declaration not allowed here.(:main:, row:1, col:46) at com.sap.aii.mappingtool.tf3.Transformer.checkParserException(Transformer.java:41) at com.sap.aii.mappingtool.tf3.Transformer.start(Transformer.java:70) at com.sap.aii.mappingtool.tf3.AMappingProgram.execute(AMappingProgram.java:231) at com.sap.aii.ibrun.server.mapping.JavaMapping.executeStep(JavaMapping.java:63) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:91) at com.sap.aii.ibrun.server.mapping.MappingHandler.run(MappingHandler.java:77) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleMappingRequest(MappingRequestHandler.java:88) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleRequest(MappingRequestHandler.java:63) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceImpl.processFunction(MappingServiceImpl.java:80) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceObjectImpl0.processFunction(MappingServiceObjectImpl0.java:131) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.ejb.session.stateless_sp5.ObjectStubProxyImpl.invoke(ObjectStubProxyImpl.java:187) at $Proxy24.processFunction(Unknown Source) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.handleRequest(RFCDefaultRequestHandler.java:95) at com.sap.engine.services.rfcengine.RFCJCOServer.handleRequestInternal(RFCJCOServer.java:113) at com.sap.engine.services.rfcengine.RFCJCOServer$ApplicationRunnable.run(RFCJCOServer.java:171) at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37) at java.security.AccessController.doPrivileged(Native Method) at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:94) at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:162)</Trace>
<Trace level="1" type="T">Runtime exception occurred during execution of application mapping program com/sap/xi/tf/_HTTP2File_: com.sap.aii.utilxi.misc.api.BaseRuntimeException; Fatal Error: com.sap.engine.lib.xml.parser.ParserException: XML Declaration not allowed here.(:main:, row:1, col:46)</Trace>
<Trace level="1" type="T">com.sap.aii.ibrun.server.mapping.MappingRuntimeException: Runtime exception occurred during execution of application mapping program com/sap/xi/tf/_HTTP2File_: com.sap.aii.utilxi.misc.api.BaseRuntimeException; Fatal Error: com.sap.engine.lib.xml.parser.ParserException: XML Declaration not allowed here.(:main:, row:1, col:46) at com.sap.aii.ibrun.server.mapping.JavaMapping.executeStep(JavaMapping.java:72) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:91) at com.sap.aii.ibrun.server.mapping.MappingHandler.run(MappingHandler.java:77) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleMappingRequest(MappingRequestHandler.java:88) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleRequest(MappingRequestHandler.java:63) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceImpl.processFunction(MappingServiceImpl.java:80) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceObjectImpl0.processFunction(MappingServiceObjectImpl0.java:131) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.ejb.session.stateless_sp5.ObjectStubProxyImpl.invoke(ObjectStubProxyImpl.java:187) at $Proxy24.processFunction(Unknown Source) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.handleRequest(RFCDefaultRequestHandler.java:95) at com.sap.engine.services.rfcengine.RFCJCOServer.handleRequestInternal(RFCJCOServer.java:113) at com.sap.engine.services.rfcengine.RFCJCOServer$ApplicationRunnable.run(RFCJCOServer.java:171) at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37) at java.security.AccessController.doPrivileged(Native Method) at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:94) at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:162) Root Cause: com.sap.aii.utilxi.misc.api.BaseRuntimeException: Fatal Error: com.sap.engine.lib.xml.parser.ParserException: XML Declaration not allowed here.(:main:, row:1, col:46) at com.sap.aii.mappingtool.tf3.Transformer.checkParserException(Transformer.java:41) at com.sap.aii.mappingtool.tf3.Transformer.start(Transformer.java:70) at com.sap.aii.mappingtool.tf3.AMappingProgram.execute(AMappingProgram.java:231) at com.sap.aii.ibrun.server.mapping.JavaMapping.executeStep(JavaMapping.java:63) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:91) at com.sap.aii.ibrun.server.mapping.MappingHandler.run(MappingHandler.java:77) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleMappingRequest(MappingRequestHandler.java:88) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleRequest(MappingRequestHandler.java:63) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceImpl.processFunction(MappingServiceImpl.java:80) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceObjectImpl0.processFunction(MappingServiceObjectImpl0.java:131) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.ejb.session.stateless_sp5.ObjectStubProxyImpl.invoke(ObjectStubProxyImpl.java:187) at $Proxy24.processFunction(Unknown Source) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.handleRequest(RFCDefaultRequestHandler.java:95) at com.sap.engine.services.rfcengine.RFCJCOServer.handleRequestInternal(RFCJCOServer.java:113) at com.sap.engine.services.rfcengine.RFCJCOServer$ApplicationRunnable.run(RFCJCOServer.java:171) at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37) at java.security.AccessController.doPrivileged(Native Method) at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:94) at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:162)</Trace>

Getting "SYSTEM ERROR" while generating a PDF in a Workflow method.

Dear All,
I'm getting a "SYSTEM ERROR" when I'm calling the below function module in a Workflow BO Method.
CALL FUNCTION wa_funcnm
 EXPORTING
 /1bcdwb/docparams = fp_docparams
 invoice = invoice
 IMPORTING
 /1bcdwb/formoutput = fp_formoutput
 EXCEPTIONS
 usage_error = 1
 system_error = 2
 internal_error = 3
 OTHERS = 4.
The aim is to generate the PDF and store it in DMS. Please let me know, if I'm going wrong somewhere. Any kind of inputs would be sincerely appreciated.
Regards,
Tushar.

Hi Tushar
You need to the following parameters when calling FM. Background WF process cannot handle dailog.
fp_outputparams-nodialog = 'X'.
fp_outputparams-getpdf = 'X'.
Refer to Thread below
Creating Attachments to Work Items or to User Decisions in Workflows
CALL FUNCTION 'FP_FUNCTION_MODULE_NAME'
 EXPORTING
i_name = l_formname
 IMPORTING
e_funcname = l_fm_name.
* E_INTERFACE_TYPE =
fp_outputparams-nodialog = 'X'.
fp_outputparams-getpdf = 'X'.
CALL FUNCTION 'FP_JOB_OPEN'
 CHANGING
ie_outputparams = fp_outputparams
EXCEPTIONS
cancel = 1
usage_error = 2
 system_error = 3
internal_error = 4
OTHERS = 5.
IF sy-subrc <> 0.
 CASE sy-subrc.
 WHEN OTHERS.
ENDCASE. " CASE sy-subrc
ENDIF.
fp_docparams-langu = 'X'.
fp_docparams-country = 'US'.
fp_docparams-fillable = 'X'.
CALL FUNCTION l_fm_name
 EXPORTING
/1bcdwb/docparams = fp_docparams
emp_info = fs_per_info
 IMPORTING
/1BCDWB/FORMOUTPUT = FP_FORMOUTPUT
EXCEPTIONS
usage_error = 1
 system_error = 2
internal_error = 3
OTHERS = 4.
IF sy-subrc <> 0.
 CASE sy-subrc.
 WHEN OTHERS.
ENDCASE. " CASE sy-subrc
ENDIF. " IF sy-subrc <> 0
CALL FUNCTION 'FP_JOB_CLOSE'
* IMPORTING
* E_RESULT = result
 EXCEPTIONS
usage_error = 1
system_error = 2
internal_error = 3
OTHERS = 4
IF sy-subrc <> 0.
 CASE sy-subrc.
 WHEN OTHERS.
ENDCASE. " CASE sy-subrc
ENDIF. " IF sy-subrc <> 0.
ENDFORM. " GET_FUNCTION_MODULE
*& Form CONVERT_PDF_BINARY
FORM CONVERT_PDF_BINARY .
CALL FUNCTION 'SCMS_XSTRING_TO_BINARY'
 EXPORTING
BUFFER = FP_FORMOUTPUT-pdf
* APPEND_TO_TABLE = ' '
* IMPORTING
* OUTPUT_LENGTH =
 TABLES
BINARY_TAB = t_att_content_hex .
ENDFORM. " CONVERT_PDF_BINARY
Regards
Sandy

How to fix file system error 56635 in windows 8.1

heelo pls help me to fix this problem i cant install any on my laptop.
file system error 56635 is showing up wen i install my kaspersky 2015

Hello Jay,
The current forum is for developers. I'd suggest asking non-programming questions on the
Office 2013 and Office 365 ProPlus - IT Pro General Discussions forum instead.

System error in Funds Management update

Dear you,
Have anyone seen the following when updating FM from FI document:
"System error:Funds management update (FMRI, CHECK_WE_RE)"
Any ideas what to do?
Thanks
Sonja

Hi there,
The update problem occurs both if we try to post with FB50L or if I try to make a transfer of FI postings in FM. This all happens in the new installation where we plan to use new GL and FM.
This note you gave did not ring a bell for me
The error message is FI057. But we have not yet found a suitable note.
Therefore any ideas are still welcomed.

Adobe Bridge gives a system error

Adobe CS4. Installed on my mac. Does not recognize Raw files and when i try to open Bridge says a system error has occured.
Adobe Photoshop Version: 11.0
Operating System: Mac OS 10.9.0
Camera Raw 5.0
Please help

Does not recognize Raw files
From which camera make and model?
Supported cameras
http://helpx.adobe.com/creative-suite/kb/camera-raw-plug-supported-cameras.html
Compatible Adobe applications
http://helpx.adobe.com/x-productkb/global/camera-raw-compatible-applications.html

SYSTEM ERROR - CONFLICT

Similar Messages

Maybe you are looking for