System hangs while I save or activate Message mapping

Hi all,
After performing the required message mapping whenever I save the Message Mapping the system hangs, it does respond but after a very long time say some 20+ minutes.
But I don't encounter such problems while saving data types , message types , message interfaces etc..
can any one help me with this?
Thanks in advance.
Ajay

Hi Michal,
I have a freshly installed PI 7.1
Im able to run file to file scenarios without mapping.
Im able to activae DT, MT, SI etc..but i dont receive any response from the system when I save a message mapping.
It takes ages to go to test tab, executes after a long time but target shows no message...
can u kindly help me on this?
has ne one faced sch an error before.. Im using PI 7.1

Similar Messages

System hangs while booting 2.6.38

My system hangs, while booting 2.6.38
The picture from the screen is here: http://bildr.no/view/844865 (the picture is not mine, but it's the same).
/ is located on raid1 array. Boot is separated to ext2.
Grub:
# (2) Arch Linux
title Arch Linux
root (hd0,1)
kernel /boot/vmlinuz26 root=/dev/md1 ro md=1,/dev/sda2,/dev/sdb2 md=2,/dev/sda3,/dev/sdb3 radeon.modeset=1 elevator=noop
initrd /boot/kernel26.img
Tried nomodeset and removing "elevator=noop".
$ lspci
00:00.0 Host bridge: ATI Technologies Inc RD780 Northbridge only dual slot PCI-e_GFX and HT1 K8 part
00:02.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (external gfx0 port A)
00:04.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port A)
00:0a.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port F)
00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode]
00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:12.1 USB Controller: ATI Technologies Inc SB7x0 USB OHCI1 Controller
00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:13.1 USB Controller: ATI Technologies Inc SB7x0 USB OHCI1 Controller
00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a)
00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
01:00.0 VGA compatible controller: ATI Technologies Inc RV710 [Radeon HD 4550]
01:00.1 Audio device: ATI Technologies Inc RV710/730
02:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02)
02:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
04:07.0 Network controller: Ralink corp. RT2800 802.11n PCI
04:0e.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)
The same here: https://bbs.archlinux.org/viewtopic.php?id=115190
Last edited by vit (2011-03-24 03:59:23)

The system is booting and hangs in other place.
Updated to .38.1
Doesn't help.
Last edited by vit (2011-03-24 15:29:49)

SYSTEM HANGS WHILE RUNNING EXP COMMAND IN ORACLE 10G

WHEN WE ARE RUNNING THE EXP (EXPORT) COMMAND IN ORACLE 10G
TO TAKE THE BACKUP IT GETS HANGED FOR A LONG TIME AND THEN IN THE LOG FILE WE FIND THE FOLLOWING ERROR MESSAGE.
SOMETIMES AFTER RESTARTING THE SERVER WE ARE ABLE TO RUN THE EXP COMMAND.
Connected to: Oracle Database 10g Enterprise Edition Release 10.1.0.2.0 - Production
With the Partitioning, OLAP and Data Mining options
Export done in WE8MSWIN1252 character set and AL16UTF16 NCHAR character set
About to export specified users ...
. exporting pre-schema procedural objects and actions
. exporting foreign function library names for user MANHAR
. exporting PUBLIC type synonyms
. exporting private type synonyms
. exporting object type definitions for user MANHAR
About to export MANHAR's objects ...
. exporting database links
. exporting sequence numbers
. exporting cluster definitions
*********************************** AT THIS POINT THE SYSTEM HANGS FOR A LONG TIME.
EXP-00056: ORACLE error 24324 encountered
ORA-24324: service handle not initialized
EXP-00056: ORACLE error 24324 encountered
ORA-24324: service handle not initialized
EXP-00000: Export terminated unsuccessfully
THE EXP COMMAND THAT WE USE IS AS FOLLOWS:
EXP MANHAR/MANHAR FILE=F:\BACKUP\MANHAR.DMP LOG=F:\BACKUP\MANHAR.LOG BUFFER=1000000 GRANTS=Y CONSTRAINTS=Y
WE ARE RUNNING THE EXP COMMAND ON THE SERVER ITSELF.
THE SERVER OPERATING SYSTEM IS WINDOWS 2003 SERVER.
Kindly give us a solution at the earliest.

You should ask Oracle support for help. There's only one entry for this error stack (Bug 3361288 - Export of XMLSCHEMA may fail with ORA-24324 in UTF8), but it should have been fixed for your DB version and , as far as I can see, you don't have a Unicode database.
Werner

System hangs if Linux tries to activate PCMCIA device

Hello
I have a Toshiba Satellite M30X-118 with dual boot system WinXp and Suse linux 6.3 pro. The problem is with the onboard pcmcia device, during installation and boot when linux tries to activate pcmcia device the system hangs.... Please if anyone has the same problem and found a solution please share it with me
Thanks

Hi
I'm not a big Linux prof, but I found some good sites about this theme.
Please check these sites:
http://pcmcia-cs.sourceforge.net/man/pcmcia.5.html
http://www.buzzard.me.uk/toshiba/index.html
http://newsletter.toshiba-tro.de/main/index.html
Best regards
Bye

Installing Solaris 7 - System hangs while determining bus Types

Hi,
I am trying to install Solaris 7 on my Compaq Presario. My system hangs immediately after the first screen. It hangs on the screen where it says "Bus Enumeration Determining Bus Type and gathering hardware configuration data. Not sure why it is doing that. Any help would be appreciated
Regards,
Ashish.

My system is not branded It is custom bulit.
What more information you want write me.
Thanks for all help
Amit

System hangs while retrieving nearly 80,000 records in HTML output

Hi Users,
I am using Oracle BI Publisher Enterprise.
When I tried to retrieve nearly 80,000 records, the system hangs.
How to get rid out of that.
Awaiting for you reply guys.

Thats common, go for summary report instead of that.

Almost every time my phone hang while I'm typing the message then it jump to the screen side.

Hang while typing the message

When was the last time you reset your phone? I suggest cleaning out the junk and try again.

Unable to activate Message Mapping (Until i restart PI )

Dear all,
I am using PI 7.1.
I am trying to activate the message mapping objects in ESR. but it is not getting activated.
I see the following error message in the process log:
Activation of the change list canceled
Check result for Message Mapping: MMtest | urn:test
                Starting compilation
     Source text of object Message Mapping: MMtest | urn:test has syntax errors:
     Source code has syntax error
The message mapping objects are simple one, and does not contain any UDFs.
Infact these message mapping object was successfully activated before.
when this occured for the first time yesterday, I restarted the PI server. then it worked.
But today, this problem is occuring again. I again restarted, it got activated.
I worked for sometime, and tried editing and activating, but again i see the same error message.
I am sure, it will work if i restart PI, but i cannot afford to restart these many times.
Has anyone faced this error message.
any inputs/help appreciated.
thanks
Ganesh

we have not changed the jdk version,
it seems that.. while compiling the message mapping into java classes, some conflicts are going on.
now to relplicate the problem, i need not try activating the message mapping object.
I can see the same error message when a do "Check" (F7) of the message mapping object.
Immediately after restarting the PI server, the MessageMapping compliation process seems to pick up the right classes/jars, so is successful.
but as the time goes on after we PI started and as we use PI, some of the mapping classes/jars values might be getting changed .. to disallow further compilation of message mapping
hmm.. thats the thought.. may need to investigate in 7.1
Ganesh

XI System hangs while designing BPM in correlaltion editor

Hi,
While designing BPM scenario in Integration repository, system gets hanged on pressing F4 while specifying condition in the correlation editor.
Thanks and Regards
Rahul Nawale

Hi,
try applying the latest path to your XI server
I had the same with SP13 and SP14 and
the latest path helped
Regards,
michal

System hangs while working with Adobe forms in Eclipse

Hi,
I am new to SAP ABAP and ABAP in Eclipse. So far we were using SAP GUI, but now we are moving towards Eclipse for ABAP.
I am creating adobe forms in eclipse using Open with SAP GUI option. I am able to create and execute in eclipse but it always hangs when I try opening the layout and then closing it. Once it hangs, I need to kill Eclipse process from task manager. Can anybody help me?
Thanks in advance.

Hello Hemika,
What is the version of Adobe LiveCycle designer on your PC ?
Looks like the Adobe LiveCycle Designer and NWDS versions are incompatible .
1055911 - Creating ZCI based interactive Forms in Web Dynpro for Java
1090464 - Interactive Forms-Web Dynpro Java-Limitations/Recommendation
Regards
Sandy

Error BCOS088 "Error in local message system: Error while allocation..."

Hello,
I getting an error while creating a support message with "help->create support message".
The message number is BCOS088 "Error in local message system: Error while allocation: Overwrite a protected Message xxx not create."
I read a lot of threads about errors while creation of support message, but nothing helps.
Here are the facts:
- The error occurs on SolMan 4.0 system (sap basis rel. 7.0, SP15).
- BCOS_CUST: OSS_MSG | W | NONE | CUST620 | 1.0
- authorization trace without error
- DNO_CUST04: NO_USER_CHECK = X
So there is no authorization error, because of no RFC destination and successfully authorization trace.
What could be the reason of this error?
Thank you for answers, Tina

Hi Tina,
internal number range used for ABA Messages/Basis Notifications should match the external number range used for service desk messages.
For ABA messages:
Goto tx: DNO_CUST01 -> SLF1 -> Details
Should show number range 01
Number ranges for this object are defined via tx: DNO_NOTIF
For Service Desk Messages (Support Message SLFN):
Goto tx: SPRO -> "Check number range for Service Desk Message" -> SLFN -> Details
Should show number range 01 internal, 02 external
Number ranges for this object are defined via tx: CRMC_NR_RA_SERVICE
Number range 01 (internal) of ABA message should match number range 02 (external) of Support Message.
You may use other ranges but you should make sure they match.
Hope this helps.

System hanging on shutdown

The home directories on my system are on NFS.
Most of the times, when users log out of their graphical session, some of their processes keep running (for instance /usr/bin/nepomukserver for KDE users and some processes related to pulse or to chromium).
When shutting down the system, arch scripts first try unmounting network filesystems, and this fails, since /home is busy; then they send a SIGTERM to processes, and this fails as well (I believe it's because the network has been halted but /home hasn't been mounted), then the system hangs while unmounting non-API filesystems.
If, before shutting down, I manually kill the user processes (nepomukserver, pulse, chromium, ...), arch is able to shutdown as expected.
Am I the only one affected by this problem?
How am I supposed to solve it?
I'm thinking about writing a script to terminate (`kill` and then `kill -9`) any process using /home (`lsof /home`), but this looks like a terrible hack...

So, since I couldn't find any other solution, decided to write a script (an init script to add to the DAEMONS array) that kills the processes using /home while halting the machine...
If anybody will ever need it, here it is:
/etc/rc.d/pathliberator
#!/bin/bash
# Path Liberator
# kills processes that are using a given path
DAEMON=pathliberator
. /etc/rc.conf
. /etc/rc.d/functions
[ -r /etc/conf.d/$DAEMON ] && . /etc/conf.d/$DAEMON
case "$1" in
start)
stat_busy "Starting path liberator"
add_daemon $DAEMON
stat_done
stop)
success=true
for path in ${PATHS_TO_LIBERATE[@]}
do
pids=$( lsof -Fp $path | sed -rs "s/^.(.*)$/\1/g" )
if [ "$pids" == "" ]
then
status "$path was already free" true
continue
fi
# kill -TERM
stat_busy "Liberating $path"
kill -15 ${pids[@]} &>/dev/null
pids=$( lsof -Fp $path | sed -rs "s/^.(.*)$/\1/g" )
if [ "$pids" == "" ]; then
stat_done
continue
fi
stat_fail
pids=$( lsof -Fp $path | sed -rs "s/^.(.*)$/\1/g" )
# kill -KILL
stat_busy "Liberating $path with SIGKILL"
kill -9 ${pids[@]} &>/dev/null
pids=$( lsof -Fp $path | sed -rs "s/^.(.*)$/\1/g" )
if [ "$pids" == "" ]; then
stat_done
continue
fi
stat_fail
success=false
done
status "Paths liberated" $success
if [ $success ]
then
rm_daemon $DAEMON
fi
restart)
$0 stop
$0 start
echo "usage: $0 {start|stop|restart}"
esac
exit 0
/etc/conf.d/pathliberator
# Parameters to be passed to pathliberator
PATHS_TO_LIBERATE=(/home/)
It seems to be working, although didn't deeply test it...
My DAEMONS array now looks like this:
DAEMONS=(hwclock syslog-ng cpufreq network crond nscd dbus rpcbind nfs-common netfs pathliberator gpm sshd @ntpdate alsa fuse gdm avahi-daemon)
Last edited by peoro (2012-06-13 11:23:17)

Message Mapping activation error-Source code has syntax errors in UDF

Hi all,
I wrote a small UDF for sum of 2 numbers:
import
udf.*
public String getsum(String a, String b, Container container) throws StreamTransformationException{
int c = Integer.parseInt(a);
int d = Integer.parseInt(b);
int e = packageDemo.getSum(c,d);
return e+"";}
In imported archives, i imported pack.jar
In D:\udf , I have packageDemo.java, packageDemo.class, aii_map_api.jar, pack.jar(has the other 3)
packageDemo.java :-
package udf;
public class packageDemo{
    public static int getSum(int a,int b)
        int c= a+b;
        return c;
Did i miss anything?? Icant activate message mapping for 2 errors:-
1.package udf does not exist
2.Function getsum, Line 3:
cannot find symbol symbol : variable packageDemo location: class com.sap.xi.tf._xml_mm_int e = packageDemo.getSum(c,d); ^Note: /usr/sap/P7R/DVEBMGS00/j2ee/cluster/server0/./temp/classpath_resolver/Mapd4214d3099dc11dd9470001d090e4bbe/source/com/sap/xi/tf/_xml_mm_.java uses or overrides a deprecated API.Note: Recompile with -Xlint:deprecation for details.Note: /usr/sap/P7R/DVEBMGS00/j2ee/cluster/server0/./temp/classpath_resolver/Mapd4214d3099dc11dd9470001d090e4bbe/source/com/sap/xi/tf/_xml_mm_.java uses unchecked or unsafe operations.Note: Recompile with -Xlint:unchecked for details.2 errors
Edited by: NagaDurga Nannapaneni on Oct 16, 2008 1:07 PM

Hi ,
Think the error is coming because the content in imported archive is not being taken into message mapping at all...so package, class, method ..nothing is identified.
Can anyone suggest the solution..
Thanks,
Durga

Local lookup in message mapping

Hi all,
I've a table on the SAP PI system filled with data. From my message mapping, I want to do a lookup.
What's the best way to perform this lookup.
Again, this is a local table. So not a table residing on the SAP ECC system.
Thanks a lot.
Dimitri

Hi,
>>>I've a table on the SAP PI system filled with data. From my message mapping, I want to do a lookup.
What's the best way to perform this lookup.
the best/easiest way would be to use ABAP mapping (right after your message mapping - as in interface
determination you can have many mappings)
just to do the lookup in XI table (in abap mapping you juse use a select to get this data)
so map the data in message mapping
then do the lookup in abap mapping just for this one field
Regards,
Michal Krawczyk

Problem with condition IF THEN in Message MApping

Hi,
We are not getting correct ouput when we use condition IF THEN without else in message Mapping .We are sending data from File to XI to R/3.
We are using file adapter and IDOC adapter to create customer in R/3.
In message Mapping we are creating Segment E1KNB1M and E1KNBKM based on condition.
IF THEN Condition used in mapping is as below
find the length of Compnaycode with LENGTH function.Pass that value as one of the parameter to function GREATER.Pass second parameter to function GREATER a constant (0).Pass the result to If without else function.If this is true pass Item to IF THEN function and Map the result to E1KNB1M.
Our mapping is not giving desired output in below scenario:
Source XML
<?xml version="1.0" encoding="utf-8" ?>
<ns:CustomerMaster_Request_MT xmlns:ns="http://mazdausa.com/sapr3/fi/masterdata/customermaster">
<Idoc>
<Header>
<ID>H</ID>
<ACCTGRP>M002</ACCTGRP>
<CUSTNO>R51563</CUSTNO>
<NAME1>WAYNE MAZDA</NAME1>
</Header>
<Item>
<ID>L</ID>
<COMPCODE>US10</COMPCODE>
<BANKKEY>0000326</BANKKEY>
<BANKCNTRY>US</BANKCNTRY>
<BANKACCT>05893</BANKACCT>
</Item>
</Idoc>
- <Idoc>
- <Header>
<ID>H</ID>
<ACCTGRP>M002</ACCTGRP>
<CUSTNO>51563</CUSTNO>
<NAME1>WAYNE MAZDA</NAME1>
</Header>
</Idoc>
- <Idoc>
- <Header>
<ID>H</ID>
<ACCTGRP>M002</ACCTGRP>
<CUSTNO>V51563</CUSTNO>
<NAME1>WAYNE MAZDA</NAME1>
</Header>
- <Item>
<ID>L</ID>
<COMPCODE>US10</COMPCODE>
<BANKKEY>000326</BANKKEY>
<BANKCNTRY>US</BANKCNTRY>
<BANKACCT>0305893</BANKACCT>
</Item>
</Idoc>
</ns:CustomerMaster_Request_MT>
Here 3 Idoc are created under ZDEBMAS06.
First IDOC contain segment E1KNB1M and E1KNBKM as desired because first idoc in Source XML contains Item data.
Second IDOC contain segment E1KNA1M only as desired because second Idoc in Source XML does not contains item data.
Third IDOC does not contain Segment E1KNBKM and E1KNB1M which is not a desired output. It should contain these segments as third idoc in source XML have item data.
But we are getting right output in case we also have Item data under second IDOC in source XML.
Please let me know where I am doing wrong.
Thanks.
Rekha.

Hi Rekha,
I am getting the same problem while checking display Queue in message mapping??
<i><b>Source code has syntax error: java.lang.NoClassDefFoundError: com/sun/tools/javac/Main Exception in thread "main"</b></i>
Any ideas to solve this problem...
Thanks,
Sekhar

System hangs while I save or activate Message mapping

Similar Messages

Maybe you are looking for