System just reboots over and over after VIA Chipset 4in1 Drivers installed

After installing the (2005-1-14) VIA Chipset 4in1 Drivers on my K7T Turbo Ver 3 system (Windows/2000 SP4, Award BIOS 3.6) I got the following blue screen:
*** STOP: 0x0000007B (0xF681F84C,0xC0000034,0x00000000,0x00000000) INACCESSIBLE_BOOT_DEVICE
If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:
Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check you hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.
Refer to your Getting Started manual for more information on troubleshooting Stop errors.
1. I logged into Windows/2000 via "Safe Mode", got the same error above.
2. I then rebooted with the Windows/2000 cd, selected Repair. Went through the Repair process, had the emergency disk. Still got the above blue screen after rebooting.
3. I then rebooted again in "Safe Mode", got the blue screen error.
4. I then rebooted again in "Safe Mode with Networking". got the blue screen error.
5. I then rebooted with the Windows/2000 cd, selected Repair. Went through the Repair process and DID NOT use the emergency disk. This time the system got to the Windows logo screen (before log in prompt) and then reboots over and over. No blue screen.
6. On next reboot, I hit F8 for "Safe Mode". "Starting Windows ..." appears on screen, then system reboots over and over.
Any suggestions?
Thanks,
Jim

To get the pc to stop rebooting over and over, I ran chkdsk /R.
Next, I booted with the Windows/2000 CD and selected to Repair.
I tried just doing the Repair, but that did not work.
I tried to log in after doing the chkdsk /R and that did not work.
I then get the blue screen when trying to login to W2K, but was able to login "Safe Mode".
I removed the VIA drivers using Device Manager:
VIA Bus Master IDE Controller,
VIA CPU to AGP Controller,
VIA Tech PCI to ISA bridge,
VIA Tech Power Manager controller.
I then clicked on the "Scan for hardware changes" icon. This added back drivers. Rebooted. Got the blue screen with errors in my first posting.
This is a little progress since the machine is not stuck in a "reboot loop" like above and I can log in to "Safe Mode".
Does anyone think that upgrading from Windows/2000 to WindowsXP will fix this? (Does WindowsXP have these drivers in pnp?)
Thanks,
Jim

Similar Messages

NEW VIA Chipset 4in1 Drivers for KT4AV BAD

Ok heres the problem. I have a KT4AV-L motherboard and I wanted to update the VIA Chipset 4in1 Drivers. While I was installing it and when it reached 100%, the screen went black and wouldn't boot back up. I had to hit the restart button to reboot Windows again. Doesn't anyone also have this problem with the new VIA Chipset 4in1 Drivers V4.51 on the KT4AV motherboard?

I haven't heard of this, but I know if not installing under Safe Mode the driver install often hang at the last percent.

I downloaded the latest version of Adobe Reader (11.0.07) and installed it. Message said install successful. But APEX learning software does a check to see if my system has Adobe Reader and it says I still need to install it. What's up? This has happened

I downloaded the latest version of Adobe Reader (11.0.07) and installed it. Message said install successful. But APEX learning software does a check to see if my system has Adobe Reader and it says I still need to install it. What's up? This has happened to me numerous times throughout the years. I need to get to the bottom of this problem. Thanks for your help.

You still don't give us the message you are receiving. My guess: you are trying to open a PDF in a browser that uses its own PDF viewer, not the Adobe Reader plugin: http://helpx.adobe.com/acrobat/kb/pdf-browser-plugin-configuration.html

Best and most stable VIA chipset drivers

Can anyone suggest which are the best VIA chipset drivers for the K8T Neo2 FISR mtoherboard (6702E)?
Live update syas 5.07A .... and that iswwhat I have at present ....
JLP

hello,
stuck with MSI drivers: http://www.msi.com.tw/program/support/driver/dvr/spt_dvr_detail.php?UID=608&kind=1

Just rebooted ipad, and now facetime and i messaging not working. I put in my apple user id(email) and password code. says network connection not available, but my iphone works fine on the wifi.??i can text throug iphone, just not ipad??any bright ideas w

Hi there. I have the ipad 3, and just last night had to reboot and do the upgrade, now my texting and facetime on it is not working...it states that when I click to activate it, and put in my user id(email) and passcode....that" could not sign in...please chekc network connection and try again".....well my Wifi connection is fine, and i can text and facetime fine from my iphone..just not the ipad now.....any ideas why it will not take my user id and passcode?...the passcode works fine on my iphone.

Hello cohenj80,
Thank you for the details about the FaceTime and iMessage activation issue you are experiencing on your iPad 3. I recommend following the steps in this article when you are not able to sign into FaceTime or iMessage on your iPad:
iOS: Troubleshooting FaceTime and iMessage activation
http://support.apple.com/kb/ts4268
Best,
Sheila M.

HT201272 why did my apps just stop opening and workng after i synced to my ne laptop and how do i get them to work??

most of my apps won't open after syncing to a new laptop why and how can I fix this?

If it's apps that you've downloaded from the App Store that you're having the problem with, and the Apple built-in apps are ok, then try downloading any free app from the store (as that appears to reset something) and then re-try them - the free app can then be deleted.

MOVED: Best and most stable VIA chipset drivers

This topic has been moved to AMD64 ATI/SiS/VIA based board.
https://forum-en.msi.com/index.php?topic=106225.0

hello,
stuck with MSI drivers: http://www.msi.com.tw/program/support/driver/dvr/spt_dvr_detail.php?UID=608&kind=1

Computer shuts off after Nvidia 8600M GT drivers installed

Hello, I recently used the Toshiba Recovery to start anew (out-of-the-box state) on my Satellite X205-SLi4. The problem is, after the Nvidia drivers (for dual Nvidia 8600M GT) were installed and I rebooted, the computer turns off during startup. I tried several times to restart, but the same thing happens. The ONLY way that my computer will run in normal mode is to run with the standard vga driver that was present befor the Nvidia drivers were installed.
Is there a fix for this? Any help would be appreciated! Thanks in advance.
I'm running Vista Ultimate 32-bit.
This is what I found in the Event Viewer:
Error 8/28/2009 6:12:10 AM Service Control Manager 7000 None "The Parallel port driver service failed to start due to the following error:
The service cannot be started, either because it is disabled or because it has no enabled devices associated with it."
Error 8/28/2009 6:11:50 AM WerSvc 5007 None The target file for the Windows Feedback Platform (a DLL file containing the list of problems on this computer that require additional data collection for diagnosis) could not be parsed. The error code was 8014FFF9.
Warning 8/28/2009 6:11:36 AM WMServer 317 (4) "The description for Event ID 317 from source WMServer cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
The following information was included with the event:
C:\Users\Mia\AppData\Local\Microsoft\Windows Media\11.0\WMSDKNS.XML
An invalid character was found in text content.
0
0
C:\Users\Mia\AppData\Local\Microsoft\Windows Media\11.0\WMSDKNS.XML.(2009.08.28 06.11.36)
Warning 8/28/2009 6:09:37 AM Microsoft-Windows-WLAN-AutoConfig 4001 None "WLAN AutoConfig service has successfully stopped.
Warning 8/28/2009 6:09:36 AM Microsoft-Windows-Winlogon 6000 None The winlogon notification subscriber <GPClient> was unavailable to handle a notification event.
Warning 8/28/2009 6:09:36 AM Microsoft-Windows-Winlogon 6000 None The winlogon notification subscriber <GPClient> was unavailable to handle a notification event.
Error 8/28/2009 6:04:52 AM Microsoft-Windows-DistributedCOM 10005 None "DCOM got error ""1084"" attempting to start the service McNASvc with arguments """" in order to run the server:
{24F616A1-B755-4053-8018-C3425DC8B68A}"
Error 8/28/2009 6:01:00 AM Microsoft-Windows-DistributedCOM 10005 None "DCOM got error ""1084"" attempting to start the service WSearch with arguments """" in order to run the server:
{7D096C5F-AC08-4F1F-BEB7-5C22C517CE39}"
Error 8/28/2009 6:00:59 AM Microsoft-Windows-DistributedCOM 10005 None "DCOM got error ""1068"" attempting to start the service fdPHost with arguments """" in order to run the server:
{145B4335-FE2A-4927-A040-7C35AD3180EF}"
Error 8/28/2009 6:00:58 AM Microsoft-Windows-DistributedCOM 10005 None "DCOM got error ""1084"" attempting to start the service EventSystem with arguments """" in order to run the server:
{1BE1F766-5536-11D1-B726-00C04FB926AF}"
Error 8/28/2009 6:00:58 AM Microsoft-Windows-EventSystem 4609 Event System The COM+ Event System detected a bad return code during its internal processing. HRESULT was 8007043c from line 45 of d:\vistartm\com\complus\src\events\tier1\eventsystemobj.cpp. Please contact Microsoft Product Support Services to report this error.
Error 8/28/2009 6:00:50 AM Microsoft-Windows-DistributedCOM 10005 None "DCOM got error ""1084"" attempting to start the service ShellHWDetection with arguments """" in order to run the server:
{DD522ACC-F821-461A-A407-50B198B896DC}"
Error 8/28/2009 6:00:26 AM Microsoft-Windows-WLAN-AutoConfig 10000 None "WLAN Extensibility Module has failed to start.
Module Path: C:\Windows\System32\IWMSSvc.dll
Error Code: 21
Warning 8/28/2009 6:00:23 AM Microsoft-Windows-Winlogon 6000 None The winlogon notification subscriber <GPClient> was unavailable to handle a notification event.
Error 8/28/2009 6:00:04 AM Microsoft-Windows-Eventlog 1101 Event processing Audit events have been dropped by the transport. The real time backup file was corrupt due to improper shutdown.
Warning 8/28/2009 6:00:04 AM PlugPlayManager 263 None The service 'TabletInputService' may not have unregistered for device event notifications before it was stopped.
Error 8/28/2009 6:00:04 AM EventLog 6008 None The previous system shutdown at 5:58:12 AM on 8/28/2009 was unexpected.
Error 8/28/2009 5:54:45 AM Service Control Manager 7000 None "The Parallel port driver service failed to start due to the following error:
The service cannot be started, either because it is disabled or because it has no enabled devices associated with it."
Error 8/28/2009 5:54:39 AM WerSvc 5007 None The target file for the Windows Feedback Platform (a DLL file containing the list of problems on this computer that require additional data collection for diagnosis) could not be parsed. The error code was 8014FFF9.
Solved!
Go to Solution.

Do you still think this is hardware related?
I do, Mia. Restoring the hard disk to its factory-new contents should result in an error-free installation, with all drivers working properly.
It's the way tech-support people verify that the hardware is okay.
"Event Viewer cannot open the event log or custom view. Verify that Event log service is running. The data is invalid (13)."
See this Microsoft article.
Error message when you use Event Viewer to open an event log on a Windows Vista or a Windows Server ...
-Jerry

Software Updates wont install - it just reboots when try to

Hi!
Suddenly after no problem since 2007 I have this issue that when updates are presented via Software Updates, those updates that i have to click on "restart" button, wich loggs me out and then the updates supposed to install - but! Before they install the system just reboots as if the updates couldnt install and then my Mac just reboots. So for a time now i have to install the updates manually, wich is annoying.
Anyone heard of this before? Tried to repair permissons but no luck

Repair permissions is in Applications -> Utilities -> Disk Utility under the First Aid section. You have to select the hard drive icon within Disk Utility to get Repair permissions to be possible to select. Most updates don't need it. Occasionally when you install new software issues may arise that make permissions go bad, which affects future software updates. This is the pitfall of using any third party software that most users learn about. It might never progress because of permissions, or a hard disk that is too full, or a corrupt download if you don't have high speed internet to get it from.

MSI 6712 (KT4V) : list of ATI AGP HD4* cards compatible (no VIA chipset problems

I still have an MSI-6712 MB with an AGP ATI 9600XT but need to get a more powerfull card (no money for new MB and all that comes with this). I had started looking at some AGP ATI HD4* cards but the first one I saw mentioned possible problems with VIA chipsets (dont recall which card). So this made me wonder. I already have a problem where I cannot go higher the ATI Drivers 8.4 (problems with VIA chipsets) but maybe with a new card, I could pass over that problem.
There is no point in looking for AGP Nvidia cards as the strongest I could find was about the same as my ATI 9600XT. SO I am stuck with going for ATI. Also, having Linux partitions, the ATI drivers no longer support less then an HD* card (so does XP).
I want to know which AGP ATI HD* cards have NO problems AT ALL with an MSI-6712 and all its VIA chipsets.
I am just tring to get better graphics with my games (some stopped working) at the lowest cost possible until I have a better salary (probably next year).

X1950 is a powerful AGP card. Still stands ground well. A little power hungry though, and mind you get one with a quiet fan - they can be a bit noisy. Don't know quite, but around 20 Amps on the PSU:s 12 volt line might do, perhaps a little more. Please have a look at the side of your PSU, especially if you are on a budget. - I'm always on a budget, but I'm a clerk sort of.
Haven't heard about the VIA comp. problems. Usually there are ways around every obstacle, or climb it for fun.

My iphone 4S wont allow me to restore a bckup of icloud it has just rebooted the os and for over 24 hours i have been trying to fix it i use this phone for my job so i need help

My iphone 4S wont allow me to restore a bckup of icloud it has just rebooted the os and for over 24 hours i have been trying to fix it i use this phone for my job so i need help. when i try to restore it says "Your iphone could not be activated becuase the activation server is unavailable, If the problom presests goto apple.com/support" It has done this for 27 hours now PLEASE HELP!!!!!!!!!

- Connect the iPod to the computer and see if iTunes sees it. If it sees it try to get the photos off the iPod.
- Next let the battery fully drain. It will likely take days. After charging for at least an hour try again
- Last, make an appointment at the Genius Bar of an Apple store.

After recent upgrade to IOS 7 i an seeing systems rebooting very frequently. it just goes offline and comeback online after some time. IS this hardware issue or others also facing the same

After recent upgrade to IOS 7 i an seeing systems rebooting very frequently. it just goes offline and comeback online after some time. IS this hardware issue or others also facing the same

Hello there, Kishoresaraogi.
The following Knowledge Base article provides some great steps to troubleshoot your issue:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Particularly:
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

How to Create a Bootable Flash Drive to do a clean install of Lion. I have tried to use the InstallESD.dmg but it still will not do a clean install so that I do not have to do a reinstall from the Recovery (That just re downloads and takes over 6 hours)?

How to Create a Bootable Flash Drive to do a clean install of Lion. I have tried to use the InstallESD.dmg but it still will not do a clean install so that I do not have to do a reinstall from the Recovery (That just re downloads and takes over 6 hours)?
The system I'm have is a Mac-mini that had SL on it and no SuperDrive. I have also call Apple Support and they have really have not been to much help over 1st did my up grade to Lion and Installed the Lion Server.... it lost my SSL that I paid for and kill almost on of my server setting, plus kill all my web servers (using apache vhosts), and not to say the LDAP will even let remote users login to your laptops.
PS: There is no way that I'm going to buy a Install USB from Apple... They have over billed me over $300.00 because the Apps Store still has bugs (Glad I did not write that App/Service)
If there is anyone that can give in the information to create a USB install stick, I would be very thinkful.

Here you are bro, courtesy of "softpedia.com"....brilliant site!!!
If you ever had problems with your Mac OS X installation you know that the first thing you should do is to check the startup volume using Disk Utility.
After the check has ended and, if the errors exceed a certain level of seriousness, the Disk Utility application will require you to restart your Mac and use its Mac OS X Install disc counterpart.
Other users may have to reinstall OS X altogether, but will find, or already know, that their SuperDrive (a CD/DVD reader and write combo drive) is not functioning properly and it will not be able to read the Install disc.
Although this might happen to Mac OS X Leopard users due to faultyhardware, the vast majority of problematic SuperDrives will be encountered inside Snow Leopard running Macs.
This is due to the updated SuperDrive firmware included in either the Install disc or the software updates one has to install to reach the latest version of OS X, namely 10.6.6.
This can be fixed by flashing the SuperDrive’s stock firmware using free command line tools that one can find for free online (I will write about this process also, but at a later time because this article only focuses on allowing you to create your own alternative USB boot disc).
If you are reading this last bit of information with skepticism, than you should know that it happened to me too. Despite all my tries to make it work properly, the SuperDrive kept on munching any inserted DVDs and just popped them out in about twenty seconds.
The workaround to this issue was to create my own Leopard bootable USB memory stick. I am not suggesting a Snow Leopard bootable stick mainly because there are lots of users that have decided to buy the cheaper, Upgrade version, which I have not tested and, therefore, I’m not sure if it will work properly once written to a USB disk.
And now, here are the exact steps you should follow in order to obtain a fully bootable Leopard (or Lion) Install disc.
Step 1 (If you already have the Leopard install disc DMG file you can skip to Step 2)
Launch Disk Utility (you can find it inside /Applications/Utilities). Here select the Leopard Install disc in the list of drives on the left and click on the New Image menu entry at the top of the window. A save message will appear where you will have to select the Desktop as a destination.
Step 2
After Disk Utility has finished creating the Leopard DMG, insert your USB stick and erase all data and reformat the disk. To do this select the USB in the list of drives on the left and, after clicking on the Erase tab on the right side of the window, choose the Mac OS Extended (Journaled) format and click the Erase button beneath.
Step 3
After the USB has been reformatted, download the SuperDuper app from HERE and launch it. Once SuperDuper starts, you will only have to select the DMG in the Copy drop-down menu, your USB memory stick on the right and hit the “Copy Now” button.
One can also use Disk Utility for this task but creating a bootable USB stick failed 2 out 4 times when copying the DMG to the stick (with the exact same settings each time). Creating the bootable stick using SuperDuper proved to be the perfect way to do it because it worked each of the 4 times I tested it.
The steps above can also be used to create a bootable Mac OS X Lion USB by using the InstallESD.dmg image you can find inside the Lion installer (named “Install Mac OS X Lion.app”) downloaded from the Mac App Store in the /Applications folder.
To locate the InstallESD.dmg right click the Lion installer, select the “Show Package Contents” entry, go inside the “Contents” folder, and from there into the “SharedSupport” folder. Inside this folder you can find the InstallESD.dmg you can use to create your own bootable Mac OS X Lion USB stick. To do so, go to the third step described above and use the InstallESD.dmg as the DMG to be copied to your USB disc.
That’s it! Once the process ends you will have a fully bootable Leopard (or Lion) USB disk that you can use as an alternative to the Apple’s DVD Install disc that comes bundled with all Macs.
To use your newly created bootable disk you will have to restart the Mac, press and hold the OPTION key until the StartupManager appears. Here, select the Mac OS X Install disk using your keyboard arrows and press return to start from the selected drive.

HT201365 I have forgotten my passcode for my iPad air and I have tried to erase it and start over, but I stuck!! I just got it and I'm just starting to activate it as a new iPad

I have forgotten my passcode for my iPad air and I have tried to erase it and start over, but I stuck!! I just got it and I'm just starting to activate it as a new iPad

How can I unlock my iPad if I forgot the passcode?
http://www.everymac.com/systems/apple/ipad/ipad-troubleshooting-repair-faq/ipad- how-to-unlock-open-forgot-code-passcode-password-login.html
iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
How to Reset a Forgotten Password for an iOS Device
http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
You may have to do this several times.
Saw this solution on another post about an iPad in a school environment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just canceling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
 Cheers, Tom

My Macbook is not working properly, I went to a Genius Bar appointment, they were not helpful at all and just told me to go off and reboot my Mac and then restore via TimeMachine. I dont know how to do this. I am extremely displeased with Apple, help me?

My late 2011 Macbook Pro is not working properly it is very slow and extremely painful to use, I went to a Genius Bar appointment, they were not helpful at all and just told me to go off and reboot my Mac and then restore via TimeMachine. I dont know how to do this. I am extremely displeased with Apple at the moment, can someone please help me?

Your problem description is generalized and non-specific. I would make another appointment at the Apple store and insist they help you execute their suggested fixes.
Incidentally, if you search this site, Apple has excellent articles re: restoring a system.
Barry

System just reboots over and over after VIA Chipset 4in1 Drivers installed

Similar Messages

Maybe you are looking for