System lockups/video corruption after adding hard drive

I have a first generation MacPro with an ATI video board. I recently added a 1 TB Western Digital "Black" hard drive, and I used Carbon Copy Cloner to duplicate the first drive onto the Black HD, which is now my new boot drive.
Ever since I did that, my system has become quite unstable and locks up frequently. What typically happens is I'll get a garbled single row of pixels in random places on the screen, and then within a few minutes it will lock up if I try to do anything that is graphics intensive such as using Expose's active screen corders to show my desktop, or opening a folder with dozens of different icons (like the Apps folder). It /seems/ like the problem is compounded when I am using FireFox, but that may simply be because I use it alot.
After the lockup the only way to regain control of the machine is to hold in the power button.
I've even gone as far as removing the original drive thinking that perhaps the system might be confused and is pulling drivers or whatever from the old drive. That didn't help.
Any thoughts as to what is happening here? It's seriously driving me nuts (not to mention wasting a lot of my time constantly having to restart the system).

Did you run Disk Warrior before and after cloning?
Repaired permissions?
Re-ran 10.5.7 combo update?
I'd even look in system profile - memory and see if there are errors showing (doesn't show errors from prior system boots though).
Cleaned out the X1900; add copper cooling kit $29, or look into another ATI card.
Before using any new drive, zero it. And if you have Windows and the drive is backed up or before you put files on it --- do a complete and thorough zero and extended test in Windows using WD's own Diagnostic utility - much better, reliable, and does map out bad blocks while Disk Utility and other OS X tools rarely do. But any new drive... I've had 3 out of 6 need such treatment.
As a test, reboot back on your original why not? I'd have done that just to narrow down the possibilities.

Similar Messages

Fans more quiet after adding hard drive

My G5 has a 250gb hard drive. When buring DVD's the fan came on like a jet. I added a 1TB hard drive, and the fans no longer sound like a jet when burning a DVD. Would this be due to the extra working space the 1TB drive would provide the system?
Thank you for any thoughts you might have in this.
JB

If it was "added," I assume there are two hard drives in there now...
If you unplugged the Power Mac during installation of the new drive, you may have reset the power management (SMU), which made the fans work properly.
http://support.apple.com/kb/HT1436
The procedure is basically to unplug the Power Mac for a few minutes and plug it back in. One of the symptoms mentioned is fan noise.

Slow Boot after added hard drives in RAID 0

Hi,
My Mac Pro used to boot very fast (from Bong to Login screen).
After installing a RAID0, it takes much longer to boot (x5).
When powering on, after the BONG, the grey screen appears and it seems frozen for a while ~30seconds. While grey screen is still on, I can hear the RAID0 hard drives finally waking up and starting to spin (I believe that they are the RAID0 hard drives because I can hear the startup disk just after the BONG). Once the MacOSX splash screen is displayed, everything goes very fast. Progress bar takes <2s to finally display login screen.
I suspect an incompatibility of the hard drives firmware with the Mac Pro even if those are very popular drives.
The Mac Pro is also sometime very slow to shutdown and when it occurs, I can hear the same sound of the drives waking up and starting to spin again.
I have disabled the hard drive sleep option in the power settings.
Here is my configuration. Disk4 has been added after the RAID0 and hasn't changed the issue. Please help.
Disk1: (Startup Disk)
Capacity: 149.05 GB
Model: ST3160812AS P
Revision: 3.BQH
Disk2: RAID0 - slice1
Capacity: 298.09 GB
Model: ST3320620AS
Revision: 3.AAJ
Disk3: RAID0 - slice2
Capacity: 298.09 GB
Model: ST3320620AS
Revision: 3.AAJ
Disk4:
Capacity: 698.64 GB
Model: ST3750640AS
Revision: 3.AAE
Regards,
Guillaume

I am still booting off of the same drive as before I added the RAID so RAID disk doesn't appear in disk control panel but I went there and reselected my initial MacOSX installation folder on Drive0. It seems to have improved things quite a bit. Was it just looking for other boot partitions on all hard drives on startup? I don't know why this setting would have changed when adding drives into the box.
Thanks.

"F11 System Recovery" during boot does not work after Cloning hard drive.

Problem: “F11 System Recovery” during boot does not work after Cloning hard drive.
HP Envy m6-1125dx UEFI Notebook Computer with GPT hard drive.
Original Seagate Hard Disk GPT 700GB with Window 8.0_64 upgraded to Windows 8.1_64
Startup Menu (F11 System Menu works properly) only on original hard drive.
Following obtained from Disk Management & diskpart in Command Prompt.
GPT Disk <700GB>
Partition 1 WINRE NTFS Primary 235MB/400MB [Recovery]
Partition 2 EFI System FAT32 (LBA) Primary 108MB/260MB [System]
Partition 3 (NONE) Unformatted Primary 128MB/128MB [Reserve]
Partition 4 Main NTFS Primary 90GB/195GB [Primary “C”]
Partition 5 (NONE) NTFS Primary 372MB/450MB [Recovery]
Partition 6 Data NTFS Primary 7GB/475GB [Primary “E”]
Partition 7 NTFS Primary 26MB/350MB [Recovery]
Partition 8 Recovery NTFS Primary 24GB/26GB [Recovery “D”]
I have Cloned the original hard drive to a new HGST 1TB Hard Drive using four different methods (sector by sector):
Acronis True Image 2015
Acronis Backup for PC
AOMEI Backupper Professional
Macrium Reflect
Each time the cloning process completes successfully and has the same original partition arrangement. The computer works properly except when trying to use the “F11 System Menu” key during boot. It gives the following error message:
“Recovery
Your PC needs to be repaired
A required device isn’t connected or can’t be accessed.
Error code: 0xc0000225
You need to use the recovery tools on your installation media. If you don’t have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. “
Any suggestions why the F11 System Recovery does not work during boot and how to fix the problem would be appreciated. I have does various disk checking and file checking on both the original and new hard drive with no errors.
Thank you in advanced.

Hi,
How did you clone the HDD ? One-for-one or different method ?
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Can't recover my system after a hard drive crash.

Hello
My hp DV6-3123tx's hard drive crashed because of a collision
Steps i did:
Got a new hard drive and fit it in.
Using recovery DVDs tried to format it.
Everything was good but when the system reboots to install drivers it just gets stuck at the starting page (on which hp is written). I waited for hours together but it doesn't recover from that state
P.S: I had removed CMOS too after my hard drive crashed but restored and saved it's default settings in BIOS before the above mentioned steps.
This question was solved.
View Solution.

Hi,
Assuming this is just a problem with the recovery media, here's an alternative option you could try.
Before trying the following, make sure you can still read the 25 Character Product Activation key on your Windows COA label ( 5 blocks of 5 alpha/numeric sets ).
An example of a COA Label can be seen Here.
You can create an installation disc yourself using another PC - just download the correct Disc Image ( this must be the exact same version that originally came with your notebook ) from the link below and use an application such as ImgBurn to burn the ISO correctly to a blank DVD - a guide on using ImgBurn to write an ISO to a disc is Here. These Images are clean and from a well-respected source, however there are only limited versions available.
Windows-7 sp1-iso-official-32-bit-and-64-bit
Use the disc to perform the installation, enter the Windows activation key found on the COA Label when requested and when the installation has completed, use the 'Phone Method' detailed in the link below to activate the OS - this method supported by Microsoft and is popular with people who just want a clean installation of Windows 7 without the additional software load normally bundled with OEM installations.
http://www.kodyaz.com/articles/how-to-activate-windows-7-by-phone.aspx
Any additional drivers and software you may need can be found starting Here.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

How do i repair or recover data from a corrupt USB external hard drive that does not show up on my Mac desktop or disk utility

How do i repair or recover data from a corrupt USB external hard drive that does not show up on my Mac desktop or disk utility?
Last night i was using my external hard drive, for some reason the folder just closed and i couldn't find it on my desktop.
After googling solutions, i found it in the disk utilities, i clicked on the 'repair' button many times, but it said the 'error...' message.
So i ejected it to try again, now when i connect the USB external hard drive it doesn't show up on my desktop or disk utilities.
I really just want to either repair or recover the data on it because it literally has everything (documents, work files, photos etc) on it,
I downloaded an application to recover my files but it needs the USB to at least show up.recognise it which mine doesn't.
I know i should've backed it up on another USB, this definitely teaches me for next time to back up all my files.
Are the files lost forever or can i recover them by going to a shop or using a software?

Thank you for responding.
This might sound stupid since i'm not really knowledgeable with Macs,
but since all my files were moved from my mac computer to the external hard drive,
is it possible to recover those files through my Mac - like recovering deleted files?

Humming sound like a ground loop with added hard drives

I get a humming low freq Hum from my MacPro from adding or added hard drives. I am using Seagates 320's ( 3 - non raid ). The MP is under my desk and I think some may not hear what I do if sitting on a desktop.
I can't figure out if it's a ground loop issue, more than one drive spinning at the same speed or some mechanical isssue, like metal to metal contact.
Just one drive with the OS. The Hum if still there is not something I am aware of or bothers me. But your room must be quiet to hear ir best.

As I mentioned before, some people will not hear the "hum" if the MP is sitting on your desk ( or one hard drive ) . Mine is under a large desk that is 6' long, which kinda amplifies the sound and creates a sound box for the low freq hum. Some what like adding a subwoofer. But when you add one or more drives it will Hum and I think I know the cause.
One is there is no isolation ( ie rubber ) between the hard drive mounting system, the (metal) inside frame and outer (metal) case. This causes the MP to become or act like a tuning fork.
For those who do hear the hum sound, you can take both hands on either side of the MP and "squeeze" the sides and hear the sound get lower. Take your hands off and hear it louder. So the whole MP is vibrating or creating "noise" or low freq Hum ( tuning fork) .
The problem is some what resolved with using 2 drives if you mount one in bay 1 and the second in bay 4. ( not side by side ) In other words, the sound is amplified to a higher degree if you have matching drives ( non raid ) next to eachother.
This issue will drive you nuts if you have it or can hear it. The MP stock 2.66 thats a month old is what I have. Maybe some other Macs don't show this same sound.
Whats interesting is the metal case, both outer and inter being connected as a "rigid unit" is causing or lets say, making matters worse. The other of which I have not plotted the freq, I think is around 60hz which just so happens to be the same as your " AC power". So the humming could sound like a ground loop, when in fact the sound originates from the hard drive and is being magnfied by the rigid non insulated MP that might be inhancing it's own "resonate frequency"and acting like a tuning fork.
Now if I am right and the MP is reacting as a tuning fork. What is the solution? I don't really know. And I have not tried any so called fixes other than switching bays. I have some ideas. But only those that would not cause a warrenty issue.
I hope Apple will take a look at the issue and see if a real engineer can first identify the issue and come up with a solution.

Recovering after a hard drive crash and restore

I have a question before I sync my iPod again;
I had a operating system hard drive crash a little while ago, and I reimaged my drive with a three month old backup, basically I rolled back my computer's state a couple months, and with it, the state of my iTunes library.
Now, my library is going to be missing songs that my iPod has, does this mean when I sync my iPod again iTunes is going to delete those songs it doesn't know about anymore? I don't recall seeing the option to "manually manage" the iPod anymore, but even in that case does this mean I can't automatically sync again?
I understand that I can't use iTunes to pull songs off my iPod but thats not what I want. Essentially I want to rebuild my iTunes library list from what the iPod has, even if it can't find the songs on the local disk anymore, I just don't want them deleted.
Maybe I'm approaching this problem the wrong way..

Hi there,
I'm struggling with the exact same issue, so I'm hoping you get a response soon from someone who knows what the g-o may be... I did sync my iPod after my hard drive crashed, but I had iTunes already configured to 'manually manage' my music, so it didn't clear my entire iPod. I'm just scared of accidentally deleting certain music off my iPod playlist that I didn't burn onto disc & so I'd lose it for good.
Let's hope someone's got an idea...

How do I keep photos and videos on an external hard drive and run the application on the macbook

I am running out of space on my Macbook and would like to move all my photos and videos to an external hard drive to free up disk space. How do I designate those drives as the destination drive when running the application (iPhoto, iMovie) on the Macbook.

Moving your iTunes Music folder   http://support.apple.com/kb/HT1449
Moving your iPhoto library    http://support.apple.com/kb/HT1229
Moving iMovie footage to another drive    http://support.apple.com/kb/HT1026

I have copied videos onto an external hard drive. to free memory on my macbook. When I try to delete these I am warned that I will not be able to use this video in existing projects How do I point iMovie to events in my external hard drive so I can pl

I have copied videos onto an external hard drive. to free memory on my macbook. When I try to delete these I am woarned that I will not be able to use this video in existing projects
How do I point iMovie to events in my external hard drive so I can play projects which use them?
MacBook, iMovie 9.0.4

Hi
You can do this - by not doing it the way You describe as it will not work.
a. the external hard disk - MUST BE - Mac OS extended (hfs) formatted -
UNIX/DOS/FAT32/Mac OS Exchange - will work for most things - BUT NOT FOR VIDEO (iMovie, iDVD or FinalCut doesn't matter)
b. Do not alter or move any folder named
• iMovie Event's - or -
• iMovie Project's
on DeskTop/Finder - at all
All moving's of Events and Projects must be done within the iMovie Application - then connections will not break.
(move them back and see if iMovie remembers them - then do move as described above)
Yours Bengt W

Trying to restore my Mac OS after a hard drive failure and my password is no longer recognized, however I can log in by double clicking on the Lion Icon? How can I reset my password

I am trying to restore my Mac OS after a hard drive failure and my password is no longer recognized, however I can log in by double clicking on the Lion Icon? How can I reset my password

First, make sure caps lock is not on.
Another reason why your password might not be recognized is that the keyboard layout (input source) has been switched without your realizing it. At the login screen, you can cycle through the available layouts by pressing the key combinationcommand-space or command-option-space. See this support article.
If the user account is associated with an Apple ID, and you know the Apple ID password, then maybe the Apple ID can be used to reset your user account password.
Otherwise*, boot into Recovery mode. When the OS X Utilities screen appears, select
Utilities ▹ Terminal
from the menu bar. In the window that opens, type this:
res
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window opens. Close the Terminal window to get it out of the way.
Select your boot volume ("Macintosh HD," unless you gave it a different name) if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Follow the prompts to reset the password. It's safest to choose a password that includes only the characters a-z, A-Z, and 0-9.
Select
 ▹ Restart
from the menu bar.
You should now be able to log in with the new password, but your Keychain will be reset (empty.) If you've forgotten the Keychain password (which is ordinarily the same as your login password), there's no way to recover it.
*Note: If you've activated FileVault, this procedure doesn't apply. Follow instead these instructions.

I am having sporadic issues after new hard drive install and recovery using Time Machine. The same sluggish response, start up screen pixelating...If I reinstall Lion will it wipe out other applications? My HD was formatted and partitioned correctly, I ha

I am having sporadic issues after new hard drive install and recovery using Time Machine. The same sluggish response, start up screen pixelating...If I reinstall Lion will it wipe out other applications? My HD was formatted and partitioned correctly, I have a late 2009 iMac.

Use the trackpad to scroll, thats what it was designed for. The scroll bars automatically disappear when not being used and will appear if you scroll up or down using the trackpad.
This is a user-to-user forum and most people will post on here if they have problems. You very rarely get people posting to say there update went smooth. The fact is the vast majority of Mountain Lion users will not be experiencing any major problems with the OS, or maybe with apps which are not compatible, but thats hardly Apple's fault if developers don't update their apps.

HT1751 My win8 pc hard drive failed. After the hard drive was replaced, I copied iTunes Media backupfiles from external hard drive (Karen's Replicator was used). ITunes does not recognize the back up files - help! (it does show cloud & recently burned m

My win8 pc hard drive failed. After the hard drive was replaced, I copied iTunes Media backupfiles from external hard drive (Karen's Replicator backup software was used). ITunes does not recognize these back up files even though the location is the same as cloud & recently burned music that does show- help! The backup files consist of 34,000+ songs; almost all burned from my own CD collection. I do have most of the songs on an ipod classic but hesitate to try to restore from that. Can someone tell me how to get these 34,000 songs to show up in iTunes? Thanks!!

This diagram shows how a typical iTunes library ought to be set out (click on it to enlarge)
The red outline highlights the media folder and its contents, the various subfolders are only created if that kind of content is in your library. The right-hand side shows the files that should be found in the iTunes library folder; sentinel is normally hidden so may not be visible. The core of your iTunes library is the file iTunes Library.itl, you need to restore this, the other library files and the Album Artwork folder, as well as the media folder, to restore your library.
tt2

MacBook Pro does not boot past apple screen after replacing hard drive

After replacing hard drive on MacBook Pro 13 inch early 2011 model, the screen only boots to the apple logo. Do I need to re-install the OS?

The problem is that the OS is not in any where else of the MacBook Pro than in the HD / SSD. If you replace the Hard Drive, then you will need to Re-install OSX into that hard drive, it's pretty easy.
1) Power up your Macbook Pro, as fast as you can press and hold the Option key (ALT). You'll see that it opens the bootable-devices you have, you'll see a Recovery partition, click it.
(If the Hard Drive contains data do the following)
2) In the menu select Disk Utility.
3) In Disk Utility go ahead and select the Hard Drive that is inside the MBP.
4) Erase the content.
(If the Hard Drive contains no data continue with the following jumping the last 3 steps).
5) Select Re-install OSX.
6) Select the Hard Drive in which you want to install it.
Follow the steps of everything else (it should take approximately 1 hour to do the whole thing).
Hope this helps!
Later.

Not solved with Blinking Folder with Question Mark after Erasing Hard Drive

Before asking, I found someone had asked exact the same question, but that was actually an unsolved thread.
Re: Blinking Folder with Question Mark after Erasing Hard Drive to try to restore to Factory Settings
Level 1(0 points)sdc3gJul 5, 2013 6:24 PM Re: Blinking Folder with Question Mark after Erasing Hard Drive to try to restore to Factory Settings
Re: Blinking Folder with Question Mark after Erasing Hard Drive to try to restore to Factory Settings
in response to Niel
Thanks for the reply, held command+R again and it is trying to pick up WiFi, but it's not picking up my network and won't accept the password even when I try to put it in manually. Any thoughts on that?
Me too had tried the command+R and failed to manually connect to my network. Can anyone help?

Well, it was solved. I shifted to other place and tried other WIFis. One of the WiFi had the 2002f problem and another was fine, so the reinstall worked smoothly eventually.
On the apple support page it says that Supported network configurations and protocols includs both WPA/WPA2, not matter what they are, but it might not be true.

System lockups/video corruption after adding hard drive

Similar Messages

Maybe you are looking for