System not posting

When I turn on the power everthing works except I don't get a VGA, Keyboard, or mouse signal. I can hear the HD spin and I see the HD LED lite up then the CD LED lite up. All the fans work, I've replaced batteries, VGA cards, Power supplies and nothing. The D link lights up as follows: Top two red, bottom two green. I'm going nuts. The monitor, keyboard, and mouse work. I've tested them.  
KT3 Ultra 2
AMD 1800+ MP
Antec truepower 380
768MB samsung registered DDR RAM
120GB HD w/ 8MB cache
ti500 Video
WinTV
linksys 100TX
Audigy
16x pioneer DVD slot load
sony floppy
XP Pro
I don't overclock.
please help.

Same problem here!
I've tried 2 different boards (KT3 Ultra2-R) almost exact same problem, no signal to the monitor.  The second board got a little further with random signal loss to
the monitor. I called tech sup and was told they haven't came across the problem but suggested flashing the bios.  I'm not sure if I want to do that just incase it might crap out during the flashing and kill the bios chip.
Already tried different cpu, memory, video card (pci & agp), power supply. Disconnected everything but same result.
Anyone got any more ideas?
I have just about enough with this board. I'm considering the GA-7VRXP if the vendor let me swap without a restocking fee. This is suck! My system has been down for 2 weeks.  :O

Similar Messages

  • System not allowing to post parked vendor invoice

    Hi gurus,
    Why system not allowing to post parked vendor invoice when workflow is used for gl document?????
    It is saying not released and no one is allowed to post???
    Thank you

    Hi Mohit,
    Post can be possible to next authorized level. Check settings or else go to FBV3 ,enter document number ,company code and year > Enter > where you can see the workflow tab > Click on that where you came to know how may release levels are assigned.
    In same view > Click on system in menu bar > services for object > Click on workflow icon > where you came to know who is the next approver.
    Regards
    Mani

  • System not allowing to post profit center

    HI
    I am doing manual FI posting. system not allowing to post to desired Profit center.
    every time it is taking Dummy profit center. even if i am changing to System throughing message
    (Dummy profit center set )
    i have not assigned the profit center to cost center. because i service ( created as cost center) are used in different profit center,
    i am doing only FI posting but system taking Dummi profitcenter..
    Regards
    Ds

    Hi,
    The concept of dummy profit center is to capture the costs of the transaction where the profit center is not assigned to
    any cost center.  Instead you can define a service profit center and assign in the service cost center so that all the cost are
    accumulated in the service cost center.  If other profit centers are assigned to respective cost centers excepting the
    service cost center, you can manually repost the cost through KB11N.  As a second option you have distribution
    cycle set for profit center for month end processing so that the service profit center will distribute the values to
    the respective receiver profit centers either with fixed amount or fixed percentage.
    Regards,
    Sadashivan

  • PCIe card causes system not to POST

    I cant install because I cant get the system  to POST.  I am trying to use a PCIe x8 raid card in a x16 slot (you can put an x8 card in a x16 slot).  However when the card is in the motherboard will not POST.  Anyone have an suggestions before I chalk it up as a motherboard/card issue and spend some $$?

    About the only thing you can do to fix a failing POST is upgrade the BIOS.  It's unlikely that that would fix an issue with a PCIe card though, to my mind.  If you have a card you know works, you can try it in the same slot to see if it's a motherboard or card issue without spending $$.

  • System does not post after Bios Flash

    After using Live Update to flash my Bios to the new version, the computer does not POST. The Bios Flash was successful - it rebooted and started normally. When I tried to restart it the normal way, it will not boot. The fans run when the "power on" button is pressed but nothing more. I cleared the CMOS using the jumpers but the problem was not solved. Can any one help?
    Can some good Samaritan give me a step by step method to resolve this problem?

    I followed the link you provided and managed to resolved it:
    1) Removed one memory stick and floppy;
    2) Cleared CMOS and rebooted successfully;
    3) Inserted floppy and reverted to the previous BIOS;
    4) Inserted the other memory stick and brought system back to full power again.
    Thank you very much for your assistance. I am sure MSI is aware of the problem and will take steps to rectify it ASAP

  • K7n2 Delta-6570 Will Not Post

    I have k7n2 delta L --6570--amdxp-2500-512 mb pc3200 ram. powmax 400w power .ati 9600 all in wonder. I swapped all parts to a better case to fit a certain location and the system will not post at all. the diagnostic d-bracket has number 1 and 4 in red while 2 and 3 are green. the book only tells me that the processor is initializing with a note saying this will show information regarding the processor (like brand name, system bus. etc. but nothing will show on the monitor. everything was working fine before the swap. i have checked everything i can think of. i would appreciate some advise. sorry if i haven't posted all the proper requrements and spec's. thanks. paul k.

    i reset the memory and cpu and video card. i think i disconnected everything in the case a couple of times to make sure it wasn't a simple blunder. nothing! i have a friend that wants to try look at it i may do that. also tomorrow i will try to post all my info like the rest of you guys have done. i'll give it a try anyway. also i done the other things you mentioned, i forgot what the questions were. you can't see the post info that i am replying to keep checking so i can answer properly and i forget things.
    thanks
    paul k.

  • AMD Athlon XP 2800 (Barton Core) will not post at FSB 166 MHz.

    Per top of the board “stickys” I have read a great number of the post on this board and done my homework to provide as much technical info to help you help me. This should explain some of it’s lengthy nature.
    Aside from Memory, HDD and Video card every thing else has been unplugged from board and power or stripped out of slots to isolate the problem.
    Presently running BIOS: A6712 V. 1B
    *As seen on face of MoBo: KT4V MS-6712   Ver:10A
    *The Original Box bar code label: KT4V-L (601-6712-050)
    K7, KT400. 5.1 chnl. S/W Audio, LAN, D-Bracket 2.
    CPU: AMD Athlon AXDL 2800 DLV4D 
    Q334763K40034  AQYHA 0447APMW
    Chip lable
    Athlon XP (Barton) Low Power Processor (Model 10) 2083 MHz
    OPGA Organic Pin Grid Array 1.50 Volt max. Temp. 85°C
    512 KB L2 Cache 333 MHz System bus (166 MHz FSB) x 12.5
    Memory: x3- PC 2700 512 mb DDR 333 Super Talent
      And shows at post as running 333MHz. MemTested to 1,000% with first 1 stick, then all 3 sticks presently on bios A6712vms.1B0. at fsb 100MHz (aprox. 24hr.) I even installed and ran other AMD utillitys while MemTest was running to “stress” the system memory with zero errors. During this period I checked Windows Task Manager > Performance, CPU usage at 100%, PF usage 1.35gb. No Probs.
    Video card: Removed: MSI AGP-8X Ti4200- VTD8X 128 MB DDR 533MHz
    Replace with: PCI card (to rule out AGP card prob.) Gilmont, nVidia 64mb
    (also tried Matrox AGP 32mb card with no different results then above cards)
    Power Supply: L&C Model: LC-B350 ATX = 350 watt
          115/130v      B/4a      60/50 hz
          +3.3v/+5v   1+12v   -12/-5v    +5vsb
          28a   35a    16a    0.8a    0.3a   2a
       +3.3v combined load 200w
    Cooler: Slim Volcano 10+,   P/N A1671,  rated for up to AMD Athlon CP 3400+ & fresh heat sink compound. Freshly re-seated.
    All PCI  slots empty as I attempt to run bare bones to eliminate problems. (except now running Vido card in 1 slot)
    Floppy Drive: ribbon unplugged from board
    HDD-0: Seagate 8 gb master, (HDD tested w/no errors)
    O/S: Win. XP w/sp2
    HDD-1: slave/  unplugged from ribbon and power
    Sony CD-Rom: Unplugged from PCI slot and power
    SATA/RAID-usb 2.0 card and other HDD’s, removed and not included till Sys. runs at full potential.
    Exterior HDD and Burner beyond the scope here and not attached.
    O/S Win. XP-sp2
    BIOS I have tried: The original; Ver:10A, ran fine on Athlon XP 1600 (1400 MP) 3 years.
    •   Then with MSI Live Update 3: Installed v. 1c which couldn’t run FSB 166MHz (MSI:” Fixes system reports incorrect message for AMD 3200+ CPU.
    - Supports Sempron L2 512K 3000+ CPU.)
    However, v. 1.c did not work and would not post at all with the newly installed Barton AMD-XP 2800. [frankly this attempt was months ago and I do not remember whether it would post at the slower 100 and 133 FSB speeds, and also to muddle my memory further I was upgrading an A7N8X-D with a Barton XP 3000 and having similar problems on the ASUS,,, which is now running fine at full potential. ; - p
    •   Then I selected and flashed A6712 V 1.7 122602, boots and runs Win.XP-sp2 at FSB 100MHz & 133MHZ.  (MSI:” Supports AMD Barton XP2800+ (FSB333) CPU
    -Fixes system sometimes will have IDE CRC error   -Fixes D-bracket2+USB keyboard, cannot use keyboard on DOS mode.)”    which couldn’t run FSB 166MHz.
    I checked with the Tech. at the local shop where I purchased the KT4V MoBo. He suggested I try a different BIOS but he didn’t specify which one. He is a personal friend and admits to some bad luck and dead boards due to flashing bios so reluctant to mess with it.
    •   Now running:  A6712vms.1B0 – MSI hid this BIOS V. found here:
    •   http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=362&kind=1
    •    On a different page than the 2 versions mentioned above. http://www.msicomputer.com/support/bios_result.asp
    •    No wonder people are frustrated and confused about different MoBo versions there ID #’s and the BIOS versions them selves as seen on this news board. MSI’s fault, no fault of anyone here trying to help.
    A6712vms.1B0
    Runs fine at FSB 100 (shows as XP 1250+) and FSB 133 (shows as XP 2200+) Booting to Win. XP-sp2 on CMOS, default setup other than minor tweaks to accommodate MSI Ti 4200 AGP 8X 125mb graphics card or Gilmond PCI card. But which couldn’t run FSB 166MHz .
    No post at FSB 166 mhz (once, it did flash a post screen stating AMD Athlon XP 2800 for about 2 sec. before going blank) Manual power down. Just now I rebooted with FSB 166, and again saw the AMD Athlon XP 2800 at top of the post screen as I hit pause break,,,, then the machine power crashed to Off. Once it even loaded Win.XP-sp2 but crashed to power off with in 2 min.
    I must have booted this beast a dozen times or more after Clear CMOS jumper each time it went to blank screen with mach. still running. Start over; set Default settings and work up with FSB 100, 133, each time to read what POST says and see if it will boot to O/S.
    Btw: I have looked for clear evidence through the not so specific descriptions MSI uses to separate these board model #s and may be part of my current problem with correct board ID = correct BIOS ID.
    Found here:
    [VIA] unofficial FAQ for KT4 series motherboards
    https://forum-en.msi.com/index.php?topic=6090.0
    Eg: - KT4 Ultra (MS-6590), 6-channel hardware audio codec
       • KT4 Ultra (Pure Version)
       • KT4 Ultra-B (Bluetooth ready)
       • KT4 Ultra-BSR (Bluetooth ready + Serial ATA RAID)
       • KT4 Ultra-FISR (Bluetooth ready, Serial ATA RAID, Gigabit LAN, IEEE 1394)
    - KT4V (MS-6712), 6-channel software audio codec
       • KT4V-L, with onboard 10/100 LAN
    - KT4M (MS-6596) micro-ATX board
       • KT4M-L, with onboard 10/100 LAN
    - KT4A Ultra, (MS-6590) NEW!! based on KT400A chipset
       • KT4A Ultra (Standard Version)
       • KT4A Ultra-SR (Serial ATA RAID)
       • KT4A Ultra-FISR (Serial ATA RAID, Gigabit LAN, IEEE 1394)
    And a very similar version of this on Official MSI site. Both seem to try and make a difference between modles with on board Lan, and Blue Tooth ready.
    Take a look at my original box sticker:
    *As seen on face of MoBo: KT4V MS-6712   Ver:10A
    *The Original Box bar code label: KT4V-L (601-6712-050)
    K7, KT400. 5.1 chnl. S/W Audio, LAN, D-Bracket 2.
    Yup, it says all this on the sticker and the in the manual and verified on the MoBo. So I can only guess at all parts of the puzzle as they gave them to me which lead me to the afore mention BIOS versions I ran, or am running. The sticker points to nearly half of the boards above except for the MS-6712 and the Ver:10a which is what I based my BIOS choices on. If someone knows differently and can lead me to official Nfo with a better answer I’m all ears.
    Just saw this: Latest Official BIOS : KT4 MS-6590 (1.4), KT4V  MS-6712 (1.8 ) , KT4M MS-6596 (1.1)>>Here: [VIA] unofficial FAQ for KT4 series motherboards
    « on: 24 October 02, 05:14:04 »  But these links and all but one link in this ‘sticky’ are broken .
    So if  (1.8) is the Latest Official BIOS for KT4V MS-6712  then what is this at the Official MSI SITE ?
    KT4V
    BIOS Type
    AMI® BIOS      File Sizes
    485KB
    Version
    1.C      Update date
    Update Description   -Support Sempron L2 512K 3000+ CPU.
     BIOS Type
    AMI® BIOS      File Size
    Version
    1.B      Update date
    2004-8-9
    Update Description   Support Sempron 2200+/2300+/2400+/2500+/2600+/2800+ CPU.
        BIOS Type
    AMI® BIOS      File Sizes
    485Kb Version
    1.A      Update date
    2004-5-13
    Update Description   - System is unstable to run 3DMark03 with ATI 9600 PRO
    - Add "PS/2 Keyboard Detection" Function.
    - Support AMD 2400+ CPU.
    BIOS Type
    AMI® BIOS      File Sizes
    514KB
    Version
    1.9      Update date
    2003-7-29
    Update Description   -Fixed Adaptec 2100S SCSI card cannot be used
    -Modify CPU temperature detection
    -Support boot from Onboard LAN
    BIOS Type
    AMI® BIOS      File Sizes
    514KB
    Version
    1.8      Update date
    2003-2-12
    Update Description   -Support AMD Barton XP3000+ (FSB333) CPU
    -Add "CPU Halt Command Detection" item in the BIOS Setup
     Please also keep in mind I’m not trying to scuff anyone’s shoes…I just want to get what’s right for my board so that it and the CPU can live up to their full, "as advertised" potential and run with the other 3 big dogs under my desk.
    This seems descriptive enough and rather lengthy. Just doing my homework and reporting my findings so I won’t include actual CMOS settings unless requested. I have notes on all settings I currently use to boot with this problem.
    Other Dogs:
      ASUS A7N8X-D running Athlon XP 3000 barton core 10 (runs fsb 400..whoknew?), Mem:2.5gb Super Talent
       ASUS A7M266-D running Athlon XP 2800 (mp), Mem: 3gb Super Talent
                                                   Athlon XP 2800 (mp)
      I don’t want to boar you with the details.
    Yes, and the above have been upgraded w/new chips GFX cards and BIOS,,, NP.
      Cut to sound track: Down on the BIOS again,,, wasn’t that Creedance Clear Water Revival?
    Any suggestions or insights are much appreciated. 

    Welcome, and thank you for a thorough input! Hope I don't miss something you already said!
    Quick version: Try setting processor voltage to 1,5 volt.
    Long version:
    Posting at wrong FSB can be put down to two things:
    1 The processor isn't what you thought it is, but I think you eliminated that.
    2 The system cannot run the processor at the correct speed. Mainly this has to with overheating, and/or that memory and processor cannot cooperate. This must be it, as you noticed the processor is correctly recognised.
    You have little connected right? Then the best thing would be to pull power cable out. Take the motherboard and redo the seating of the processor, this is much better done with motherboard taken out.
    At the same time, I suggest you clear CMOS. Should always be done when changing processor, and I've noticed on the Internet there are a few 1,5V XP2800 around.
    http://64.233.183.104/search?q=cache:Q4eIa6OhudcJ:forums.amd.com/lofiversion/index.php/t47487.html+AXDL2800DLV4D+problem&hl=sv&gl=se&ct=clnk&cd=1

  • MSI Big Bang Xpower II did not post - Debug LED Code #67

        
    I need HELP...!
    I have a problem my board did not post , did not start and i have the DEBUG LED CODE # 67 displayed.
    There is my build
    MSI Big Bang Xpower II X79 LGA2011
    Intel Core i7 3820 LGA2011 Processor
    Corsair Cooling Hydro Series H100 CPU Cooler System LGA2011
    G.SKILL Ripjaws Z Series memory (F3-12800CL-32GBZL) DDR3 1600 PC3-12800 - CL10-10-10-30 (8192MB X 4) - 32GIG located in DIMM 1-3-5-7
    Gigabyte GTX570 OC Edition video card in slot PCI-E2
    Western Digital Velociraptor 300GB 2.5" SATA 3.0Gb/s 10,000 RPM
    LG BH12LS35 Blu-Ray Writer 12X BD-R 16X
    Ultra LSP-750 Power Supply
    Cooler Master HAF X EATX Tower Case
    When I put the power on, the power supply activated fans and drives spin, all the LEDs on the motherboard light up but nothing appears on the screen.
    No video signal at all and the computer stop and restrart every 15 seconds. When these reset occurs there is no beep on the speaker , nothing at all, no flashing screen either, nothing.
    The DEBUG LED display a sequence of flashing numbers 19 - 60 - 19- 60 - 67 and stop showing still the number # 67 for about ten seconds and then he reset again.
    I carefully followed the instruction manual for the installation, I installed the memory modules in slots 1 3 5 7, i put my video card in slot PCI-E2. all the power wire are connected correctly 1 x 24 pins ATX, 2 x 8 pins ATX, 1 X 6 pins , all the wire from the front panel are correctly connected to the m-connector in JFP1 & 2.
    Did i forget something, I don’t know what the debug led code # 67 exactly mean and what i have to do to fix-it
    Someone has an idea what is wrong or have any suggestion to solve this issue.
     Thank's all for your help.

     
    I followed some advice to remove the memory modules and this is actually caused by the use of memory but you will see I still have a curious bug.
    I referred to the instructions manual to the letter for the choice of DIMM SLOT to put the memory module in single, double, triple and quad channels.
    If I install 1 memory module in the DIMM SLOT  1 to operate in single channel, everything is normal and the motherboard  POST normally and show  the SETUP SCREEN.
    If I install 2 memory modules in  DIMM SLOT  1 & 3 to run in dual channel, everything is normal and the motherboard  POST normally and show  the SETUP SCREEN.
    If I install three memory modules in DIMM SLOT 1 - 3 - 5 to run in triple channel, everything is normal and the motherboard POST normally and show  the SETUP SCREEN.
    As soon as I install four DIMMs modules mémoiredans SLOT 1 - 3 - 5 - 7 to run in quad channel, the motherboard  freezes and does NOT POST and show  code 67 on the debug led and has reset itself every 20 seconds.
    I tried all my RAM modules alternately in both single channel and everything works normally.
    I did the same thing in rotation for both dual and triple channel and everything is still normal with all fourth memory modules individually.
     As soon as I put a fourth memory module it freezes and displays the code 67 or L9 dependent side as you look. 
    So my bug is my motherboard MSI Big Bang Xpower II do  not want  to work in quad channel.
    Do you have any idea where I should look for, is a setting in the BIOS  , I have flashed the bios to the latest version V1.5
    I included the screenshot of the BIOS to see if you can  notice something wrong. 
    Thank you

  • Query on GR/IR Clearing - does Not post to Profit Center.

    Pl refer the business scenario given below.
    Request your help on the following.
    Situation: For a given Purchase Order,  GR (MIGO) is done. But IR (MIRO) is not yet done.
    The FI entries are :
    1. Dr. Stock valuation a/c
        Cr. Gr/ir clearing a/c
    2. At the period end, when we do the GR/IR clearing (F.19) (prog : RFWERE00) for such a PO system will posting the following entry:
    Dr. Gr/ir -recd not invoiced
    Cr. Delivered but not Invoiced a/c
    The second entry is reversed at the beginning of next month.
    Issue:
    the first entry is posted with a Profit Center.
    While the second entry carries the dummy PC (maintained in 3KEH)
    requirement:
    The second entry should carry the PC of the original entry.
    Thanks
    Jai

    Hi  Ramesh.
    Thanks for the response
    1. Why doesn't this happen automatically?  (is it a standard sap behaviour not to post on the  Profit Center of the Original entry)
    2. I had checked substitutions. But this seems to be for Sales Orders rather than for GR /IR.  Moreover we have over 100 Profit centers and Business areas..So this seems impractical at this point in time.
    Pl give your comments/inputs.
    Regards,
    Jai

  • I am using laptop hitting and slow system not working

    i am using laptop hitting and slow system not working and very late opan file browser every think . plez help me

    Hi,
    Shut down the notebook.  Tap away at the esc key as you start the notebook to enter the Start-up Menu.  Select the Bios option ( usually f10 ) and under the Advanced or Diagnostic tab you should find the facility to run tests on both the Hard Drive and Memory.  Post back with the details of any error messages.
    Note:  If the option to run these tests is not available in the Bios Menu, use the f2 diagnostic menu instead.
    Can you also post back with the following details.
    1.  The full Model No. and Product No. of your notebook - see Here for a guide on locating this information.
    2.  The full version of the operating system you are using ( ie Windows 7 64bit ).
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Fixed asset Write up Error. ABZU(Parallel depreciation area 32 is not poste

    Hi Sap Gurus,
          I am running into an error when trying to post a write up via "ABZU". Here is the error message "Parallel depreciation area 32 is not posted". Message no. AA565.
    Diagnosis
    The asset to be posted does not manage parallel depreciation area 32, or transaction type  that you are using is limited to certain depreciation areas, and does not contain depreciation area 32. This is incorrect.
    System Response
    Posting is rejected.
    Procedure
    Check the asset and the transaction type.
    I tried "Limit Transaction Types to Depreciation Areas" in t-code:OAXE for derpeciation area 01 and 32 but still i am getting the same error. I am using ttype:700. When i look into derpeciation tab in asset master record i have depreciation area 32 is there. Is there any configuration piece i am missing. We are using area 32 as IFRS in group which is copy of 01.
    Any help will be appreciate.
    Thanks and Regards,
    Babu

    Hi,
    There are the following reasons:                                                                               
    1) The wrong transaction type is being used.  Please verify that  you are using transaction type in the 700 series for your write-up.     
    2) The transaction type is restricted to certain depreciation areas.   In transaction OAXE the transaction type can be restricted to post  only to certain areas.  If the asset manages a parallel area you  have to extend the posting to include the parallel area.                 
    3) The asset was created before you introduced parallel currencies and  does not manage the parallel area.  In this case, the parallel  area must be created on the asset or the values need to be  transferred to a new asset that manages the parallel area.                       
    4) Transacion types 600 and 601 can only be used for assets that have a  calculation key in their depreciation area that allows no automatic  calculation (for example depr key MANU).  The unplanned transaction types however can be used with assets that  allow automatic calculation.                                                     
    You also need to verify that there are entries in Table ANLB for the  asset in question for the depreciation area. 
    5) Your company code uses parallel currencies (currency types 10-co.code  currency, 50-Index based currency, 30-Group currency...for example).  The assets created in this company code must have the depreciation areas for parallel currencies active. You can only do this in activating the depreciation areas with  parallel currencies for all the asset classes used in this company code.                                                                            
    Check transaction OAYZ to make sure the areas are activated for all  asset classes in the co.code.  If not, you will need to       activate these areas and ensure the asset has all areas assigned.                
    regards Bernhard

  • K8T Master2-Far Will not POST unless CMOS is freshly cleared!

    Hey all, thanks for helping out.
    I came back to my computer one day to find it in a coma. The system was on, but the screen was getting no signal and would not come on by moving the mouse/keyboard like usual. I thought that maybe it had turned off the monitor for power save and then frooze some how. After restarting the computer I found that it was still doing the same thing. I shut down the system and unpluged. After waiting about 5 min i plugged back in and flipped the switch on the powersupply. This started the computer right up (even though i had not pushed th power button) and left it in the same condition as before. It simply would not post. After closer inspection I found that it was not posting because it wasn't getting far enough in the process before it was being restarted. I checked the restart button and even went as far as removing it from the motherboard. This did not help. I knew it was restarting because i could see it checking the optical drives then waiting for about 4 seconds, then a weird noise from the speakers (like a soft cruching so to speak) would happen, then it would do this all over again, non stop. That noise was familliar though, it was the normal noise that I hear when I push the restart button (I'm guessing a release of electricity etc..) so I knew what was going on.
    After switching the memory out and in all orders, I stripped the system down to the bare min. This however did not change anything. I put the system back together and flashed the cmos. This made the system restart once, then "BEEP" it posted. It said CMOS Checksome Error - Defaults Loaded. I first pushed DEL to get into the bios. I changed everything back to how its suppost to be (time, apature, etc...) then saved and exited. This made the system go back into its restarting state. I then flashed the cmos again and pushed F1 to continue. The system booted up just fine. In safemode of course. Then i restarted. It then went back into its restarting state. I flashed the bios again. And after pushing F1 to continue selected it to go into windows normally. Everytime it does this it gets different results. One time it got past the windows xp loading screen and sat at the black screen before you get your curser and welcome screen (sigh... restart... flash..). It also once got in just fine, and after about 5 min got a blue screen about "bad pool caller". It most the time however gets a random blue screen right after you see the welcome screen. These blue screens consist of "bad pool caller", "IRQ Equal or Lesser Value", or No notes, just generic blue screen.
    If i change anything in my bios it will not post. If i dont flash the cmos, it will not post. If i dont change anything in bios and continue, then restart, it will not post. The only way for it to post and for me to see anything on the screen is to flash the cmos. I thought it might be the power supply, but the only extra i have does not have the extra plug to power the 2nd cpu. After thinking about it though. I dont know if it could be a power supply issue, if it was then would it even load up into safe mode? Or why would it not load up into safe mode again after restarting. I have tried an extra stick of memory that i know works in a separate computer, but nothing changed. I have tried a different videocard... nothing changed. I have removed everthing accept the basics (motherboard, cpu's,videocard,memory,psu) and nothing changed.
    I have worked on this for about 1 week now and can not figure it out. I have my useless MCSE/CSE/A+ certifications (I say useless because I dont have a job that uses them) but this one is beyond me. If anyone could help I would appreciate it.
    Thanks,
    Brandon
    P.S. I dont know if this is related, but I did have to change from useing the DVI connection to RGB plug to even see anything once I heard it post. I was useing DVI before, and once i figured out that it would post after flashing cmos, I had to change to RGB to get any visual. The DVI will not work now at all. I have even tried changing cords. The DVI wont work in safemode either. Thanks

    I reckon these mobos have a fault that really needs to be sorted.  You say that your PC was working fine using PC 3200 memory with 240's. I have a similliar problem, I am using 246's with Kingston' PC3200 KVR333X72RC25/512D 2.5 ECC REG.  The PC worked fine for about two weeks and then one day went on a blink, every time I power it up all I get is beeps.  I was forced to order new BIOS, which didn't work everything else has been tested and works fine.
    So I ordered micron memory 2X512 PC 2100 266 ECC REG which I was told by the supplier that it was compartible, that didn't work either.  I then went on to check the battery, to my surprise the battery was low so I thought I had nailed it, went out bought a new battery but the problem still exits.  I must say though after installing the micron memory it did boot up but when I went into BIOS to change settings to boot fro CDROM  the damn thing would not restart I had to switch it off using the power button to restart it and when it restarted all i got was beeps.  After that to  get it to bootup I have to reset CMOS using the jumper and when it boots up it gives a checksum error message.  I have a choice of two at this stage
    (1) To Press F1
    (2) To Press delete o go into BIOS setup
    The F1 option takes me as far as the windows log on screen and that's it cuts off as if it is gonna boot itself backup but just hangs there.
    The Delete option takes into BIOS which when exited the PC does nothing until powered down and powered up again, from here I have to reset CMOS to get it to bootup.
    I have been told that the  kingston memory is not compatible but my question is how did it work the first two weeks?
    Good ol' Bas have helped out on this one quite often but here I am three months on still in a struggle.  I thought of RMAing the board but it would cost me about 160 pounds and with that kind of money I could pick up another boad from kompllete.com and remain with some change for a couple of buds.
    "To bass You said in the last post that the poblem could be the power supply changed it but that has not solved my problem"

  • Accumulated depreciation is not posted at the time of  sale of asset with r

    hi
    all
    i have created a asset with acquisition date 1.4.2011. i have posted the  acquisition value as 20000 inr.
    i have executed the depreciation run in  AFAB t.code  for april2011, may 2011,.. the depreciation is posted. in august i am retiring the asset with revenue in f-92. at this time  the accumulated depreciation is not debited .  the system is taking the difference between the acquisition value and sale proceeds  to loss on sale of asset directly.
    pls suggest me what is to be done
    thanx  in advance

    yes, i have assigned  the GL account for the accumulated depreciation on the asset in AO90.  when i  execute the depreciation run the system is posting the entry
    depreciation a/c     dr
        to  accumulated depreciation on asset a/c
    but at the time of retiring the asset  it is not debiting the accumulated depreciation on asset a/c.
    any how thanx for Ur reply

  • Reports are not posting with report repository webserver configured for Sin

    Hi Everyone,
    We have configured Single Signon on our Test environment (UADB1) using Sun Authentication Manager. Everything went well, we can login using our LDAP accounts except for one thing. The reports are not posting to the report repository.
    Our setup goes like this. We have used only one webserver for login and for report repository purposes. SSL certificate was configured in the webserver and we are using https in the report node. Both URLs https://dv001.test.com:8450 and http://dv001.test.com:8400 were configured for Single Signon.
    Report Node Definition
    Node Name: uadb1
    URL: https://dv001.test.com:8450/psreports/uadb1
    Connection Information
    https
    URI Port: 8450
    URI Host: dv001.test.com
    URI Resource: SchedulerTransfer/uadb1
    Below is the error I am getting. If I will use another webserver which is not the Single Signon configured as report repository the reports are posting. So, I am thinking this has something to do with the Single Signon setup and SSL. ANy idea? Thanks.
    PSDSTSRV.2093190 (10) [06/13/10 01:05:43 PostReport](3) 1. Process Instance: 9499/Report Id: 8465/Descr: Process Scheduler System Purge
    PSDSTSRV.2093190 (10) [06/13/10 01:05:43 PostReport](3) from directory: /psft/pt849/appserv/prcs/UADB1/log_output/AE_PRCSYSPURGE_9499
    PSDSTSRV.2093190 (10) [06/13/10 01:05:44 PostReport](1) (JNIUTIL): Java exception thrown: java.net.SocketException: Unexpected end of file from server
    PSDSTSRV.2093190 (10) [06/13/10 01:05:44 PostReport](3) HTTP transfer error.
    PSDSTSRV.2093190 (10) [06/13/10 01:05:44 PostReport](3) Post Report Elapsed Time: 0.2300
    PSDSTSRV.2093190 (10) [06/13/10 01:05:44 PostReport](1) =================================Error===============================
    PSDSTSRV.2093190 (10) [06/13/10 01:05:44 PostReport](1) Unable to post report/log file for Process Instance: 9499, Report Id: 8465
    PSDSTSRV.2093190 (10) [06/13/10 01:05:44 PostReport](2) Process Name: PRCSYSPURGE, Type: Application Engine
    PSDSTSRV.2093190 (10) [06/13/10 01:05:44 PostReport](2) Description: Process Scheduler System Purge
    PSDSTSRV.2093190 (10) [06/13/10 01:05:44 PostReport](2) Directory: /psft/pt849/appserv/prcs/UADB1/log_output/AE_PRCSYSPURGE_94

    Duplicated thread : Reports not posting if using Single Signon webserver as report repo
    Nicolas.

  • Manual BRS system not picking the doc for clearing the payment

    While processing Manual bank statement if i am  using referance doc no system not picking doc no for clearing the bank payment. So that after finishing BRs I am matching the doc manually, in f-04. This is taking long time for processing. Anyone can tell me why ref doc no not working and to make it to work, or else any problem is there to use the field. please solve my query.
    Edited by: MANISFICO1 on Aug 1, 2011 11:49 AM

    Hi:
           Please follow as given and hopefully you will be able to resolve the issue.
    1...Go to SPRO...Financial Accounting....Bank...Business transactions...Payment Transactions...Manual Bank Statement..Create a new transaction with sign - and do not assign anything in posting rule for now and enter 15 in Algorithm field , save.
    2...In define posting keys and posting rules...create an account symbol for the one you did in step 1..In Assign account to account symbol please use account symbol created earlier and acc mode + and currency should be + too. In GL Account area please list the outgoing GL which you are using for outgoing postings..
    In create key for posting rule define a posting rule and now go back to step 1 and assign the posting rule you created to the transaction type
    In define posting rules please maintain posting rule as define above...in posting area assign 1. give nothing in first posting key.assign account symbol as created earlier...now give give posting key 50..give account credit Bank...and a suitable document you use for posting BRS...In posting type give 4.
    Your Manual Bank statement is ready ....
    Go to FS00 select your bank outgoing GL account there and in create/bank.interest tab double click on Field status group..in general data make assignment number mandatory for posting...
    Go to FB50....post and outgoing transaction using the GL given above it will require you to enter assignment number enter 123 and post.
    In FF67 Select the new statement , proceed with your normal data entry and give the transaction you created in above , enter value date, amount and in bank ref field enter 123 as given in FB50.
    Save and post it. Now it should work.
    Regards

Maybe you are looking for