System not using all avail. mem.

Hi all, did a lot of forum searching and haven't seen this topic.
I'm using PPCS5(in production Premium) While rendering, the program is not using all available memory. before I go on here is the system I am using:
Win7pro
EVGA X58FTW mobo
I7 970
6x4gig Kingston hyperX 1600 RAM
Quadro fx4000
WD 140gig Raptor sys. drive
2x1TB RAID 0 (3gig SATA) data
2x2TB RAID 0 (6gig SATA) data
see image:
I have 21gigs allocated to the program.
Is the bottleneck the cache memory?
This is what I'm outputting:
Thanks for looking.

Bob Sackter wrote:
I am encoding H.264 640x360
Source is 1920x1080p60 HDV 8 sources, With a timecode window
bitrate set at 2.0 1 pass VBR
I'm making a multicam reference.
There is a little contradiction in the information here, HDV is 1440 x 1080 i60 or possible p30 I do not know of any camera that is 60p

Similar Messages

CS5 not using all available memory/CPU

I'm sure this is the opposite complaint you usually get, but for some reason AME will only sometimes use all available memory/CPU power. I'm on an 8 core Mac Pro, and while AME will sometimes register as using ~%1,000 CPU and just blitz through videos, other times it hovers around %100 and processes at regular speed. Right now, for example, it's using about 600 MB of memory, leaving over 3.6 GB free. Is there any way to assure that it always runs at max speed?

There's another thread with a similar set of issues. Other than the disk subsystem, there is another possibility for the bottleneck. That is, the codecs that are used to decode the input video files may not be efficiently multithreaded. Hence the codec responsible for creating the output file, the CPU and the disk subsystem all could be lightning fast and collectively they may all be waiting for frames to be served up by the decoder. You can check whether the disk subsystem is the bottleneck by creating a RAM disk (assuming that you have enough system RAM) and both putting all input files on and writing the output files to the RAM drive.

Macbook Pro not using all available resources

Hey All,
I have a MacBook Pro with Retina Display (Late 2013) with the 750M and 16 GB RAM. I monitor most of my resource stats with MenuMeters and I've been noticing that it doesn't use all the available power to complete a given task, I assume to save battery life. What I'm wondering is, can i change some settings to allow my processor to run faster (not overclock, just use a higher percentage of available CPU power)? For example, I was updating league of legends, and the launcher was scanning itself to check for discrepancies. It took a minute or two and I noticed that my CPU percentage hovered around 20-25% and my SSD read speeds were not even close to the theoretical maximum (I've got the PCI-e interface). Is it just poor programming that doesn't let my computer work its hardest? I feel like I have a Porsche with governor on it.

Expanding on the above, with 64-bit systems like Mountain Lion, RAM becomes critical. 4GB is a bare minimum. And will fall short if you add a few hungry apps. What happens then? Unix's fallback for low RAM conditions kicks in: virtual memory. The system tries to simulate what it does not have: extra "RAM" in the shape of a chunk of hard disk space where unneded stuff gets dumped to free real RAM. Now the system starts to lag as it desperately tries to guess which part of stuff in RAM can be moved to the disk and waits till the slow disk operation concludes. Worst case is when space runs out in the drive and all comes crashing down.
So, upgrade and give the big cat at least 8GB RAM. Can go up to 16GB. And always leave AT LEAST 10% of the drive empty.
Lastly, if you want to know what your cores and threads are up to, start up Activity Monitor. Click on the CPU tab at the bottom part of the window. Then double-click on the CPU graph. A new window will pop open, showing the load on each thread the CPU can handle concurrently.

Photoshop CS6 not using all available computer memory [was:Hello all]

I have the creative cloud trial version, and when I use photoshop cs6 it will not allow me to use all of the memory. I would love any help that can be offered.

Sound like you starting the 32 bit version of Photoshop on a Windows system. If you have a 64 bit Windows system both the 32bit version and the 64bit version of CS6 is installed. Look in you start button you should sett two CS6 start icons one for each version. Only the 64 Bit version can use more than 4GB of Ram.

2nd monitor not using all available pixels

So am I the only one having this issue? -
I have a Mac Mini that is running Windows 7 in bootcamp. I have 2 monitors. My 2nd monitor is connected with an HDMI to DVI cable. In Windows, the whole screen of both monitors is used (edge to edge, top to bottom). But when I switch over to Yosemite, my second monitor has about a 1 inch bar of black on both sides and a 1/2 inch bar along the top and the bottom. This is literally unused space.
I've talked to Apple Support several times but they don't seem to have an answer. I get transferred to someone but each time I get cut off. (so I gave up trying to fix this over the phone or on line chat). There are no features or selections in the Syncmaster to adjust this. Why does it work perfectly fine in Windows but not when I switch over to Yosemite.
Maybe this doesn't seem like a big deal but it's so frustrating that I'm actually finding myself not wanting to use the Yosemite side.
Does anybody have a solutio

Sorry:
Display TypeLCD monitor / TFT active matrix
Diagonal Size20 in
Aspect RatioWidescreen
Native Resolution1600 x 900
Pixel Pitch0.2768 mm
Brightness300 cd/m2
Contrast Ratio1000:1 / 15000:1 (dynamic)
Color Support16.7 million colors
Response Time5 ms
Horizontal Viewing Angle170
Vertical Viewing Angle160
FeaturesHDCP, MagicBright 3, MagicTune
Dimensions (WxDxH)19.1 in x 7.9 in x 14.7 in
Weight9.7 lbs
ManufacturerSamsung model 2033SW

System service using all CPU w/XP SP1

I have a K7N420Pro and after I install XP SP1 the system service uses all available CPU cycles. If I check the task manager my CPU usage is at 100%!! has anybody else seen this?
By the way, It is the system service not the system idle process.
System specs:
K7N420Pro
Athlon XP 1900
1.5 GB Ram (3x 512 MB)
2.6 BIOS

I pulled EVERYTHING off the MB. Floppy, CD/DVD drives all the memory except one stick, I even disconnected the USB and diagnostic leds. That didn't work. Then I realized that the small sound card addon wasn't actually part of the MB even though it came with it. I powered down and pulled the CNR Sound MAX card and when I rebooted it found some additional sound hardware and the system service was back to no CPU usage. I then shut down and readded the CNR card and when I powered on the system it was still fine. I now have to reconnect all the rest of the stuff I removed and make sure it is still fine but it looks good so far.
Well, It's not fine. When I rebooted the problem was back. I will now pull everything off again and then add it back one piece at a time. :(
OK
Now I finally know what the problem is.
I had both of the additional USB connections filled. One from the diagnostic thing and the other from the front of my case. Well I guess that the cables from my case are bad since when they are connected my problem is there but it goes away when I remove them. I can definitely live with just 4 USB ports. I only have 3 USB devices right now and if I ever get more I can just add a USB hub.

SAP job not using all dialog processes that are available for parallel processing

He Experts,
The customer is running a job which is not using all the dialog processes that are available for parallel processing. It appears to use up the parallel processes (60) for the first 4-5 minutes of the job and then maxes out about 3-5 processes for the remainder of the job.
How do I analyze the job to find out the issue from a Basis perspective?
Thanks,
Zahra

Hi Daniel,
Thanks for replying!
I don't believe its a standard job.
I was thinking of starting a trace using ST05 before the job. What do you think?
Thanks,
Zahra

Premiere Pro CC not using all resources... 4k

I just put together a new workstation machine for editing 1D-C 4k files in Premiere Pro and After Effects.
Specs...
i7 3770 3.4
Gigabyte Z77 Mobo
32gb Corsair Vengance DDR3 1600 RAM
250gb Samsung SSD
4x 2TB Seagate 7200 HDDs in RAID 0 (Yes I know it isn't backed up, we have that part covered)
Nvidia Quadro K4000 (3gb vram)
Anyway, we transfered a project with all the media files to our RAID media drive.
It opened up very quickly and loaded all the media much faster then our old workstation.
Then I hit the spacebar (perview) and the problems started..
It won't play back smoothly at all,
AND it is only running the CPU at 10-20%, GPU 10-50%, ram at 25% and it is not really taxing the drives very hard either...
Why won't PP use all the resources at 100% like I have previously seen it do on other machines?
** The project we are trying to play is 2 layers of 4k .MOV footage in a 1080 timeline... with sharpening, Fast color corrector, and RGB curves.
** It also drops every fourth frame when playing back just one layer of 4k .mov footage in a 1080 timeline with NO Effects applied. (Much smoother, but still not using all resources)
What I am asking, is why would it be giving up so quickly? Before even taxing the resources very hard?

I too have a recent 1D-C project I'm editing. That 1D-C is something, yes? Most filmic images I've ever seen from a DSLR. But I digress.
I'm following a workflow closer to the one used by Philip Bloom and Shane Hurlbut. The Motion Jpeg files will not play well at all on your system. It's strictly a capture medium - not an editing one.
I converted all my 1D-C files to Prores 422 at 4K size using Mpeg Streamclip. Those files imported beautifully and edit well on my Retina Macbook Pro laptop. I usually set playback to 1/2 quality, ps.
I have had problems using CUDA, so I'm sticking to software mode. But I don't see any problem with being able to cut my film and finish on my computer.
Also - my sequence is a 4K sequence right in Premiere. I simply chose a clip and "made a sequence" from that. Why scale when I don't have to? I've exported to 1080p easily from the sequence.
If anyone finds this workflow less than ideal, I'm all ears. Thanks.

HELP: Premiere Pro CC not using all CPU and RAM during rendering and export

Hello,
I am using Premiere Pro CC on a Windows 7. My timeline is quite simple with two videos, one with the movie (mpeg) and the other with the subtitles (avi).
When I render the sequence in PP or export, the rendering time is way too slow and it only uses around 15-20% of the CPU and 3 GB of RAM.
My hardware config is :
- CPU : i7-4770k 3.50Ghz
- RAM : 8 GB
- Disk : 2 x 3 TB SATA (no raid)
RAM is not the bottleneck, neither the disk access.
I have tried rendering and exporting the same project on an iMac (with an i5 2.7 Ghz and 4 GB RAM and only 1 disk) and the result is 4x faster !!!
The CPU usage is close to 100% as well as RAM usage.
So how come PP uses all resources availble on an iMac and not on a Windows 7 ?
Is there any known bug or software bottleneck on Windows 7 ?
My machine is brand new and nothing much installed besides Adobe products.
Any help is very much appreciated.
Thanks,

I just rendered out a a 2 minute sequence with about 100 clips in it and Colorista effects on everything to the Vimeo 1080 H264 preset. It took about 5 minutes to render straight from Premiere, it used all the recourses it could, my CPU was running at near %100, same with my ram and GPU, I was happy.
Then I did another render with Red Giant Denoiser and it now wants to take 30 mins and it is only using about %20 of the recourses available. My problem isn't that its taking longer with Denoiser but that its not using all of my computers CPU and GPU.
Im rendering at maximum render quality and bit dept to H264 (Im happy to wait the extra time), if I try to use VRB 2 it encodes 1 pass at a time and wants to take up to 40 minutes.
I would appreciate some advice on this.
Premiere Pro CC 2013
2.6 GHz Intel Core i7
NVIDIA GeForce GT 750M 2048 MB (CUDA GPU enabled in Premiere)
16 GB 1600 MHz DDR3
OS X 10.9.4 (13E28)

How can I make app use all available space in window?

Hi,
I'm trying to embed my flash app in a browser window and have
it use all available space. I've found plenty of tutorials online
that tell me how to make it take up the whole window, and they
work, but that isn't what I want. I have other content on the page
(a bar of links across the top). I thus want the flash app to take
up the full width and almost all the hight, leaving enough vertical
space for the link bar at the top. Right now, I have it set to 100%
for both height and width in the object tag, and it displays the
link bar, but the bottom of the flash gets chopped off (an amount
exactly equal to the height of the link bar). It seems that setting
height=100% means 100% of the full window height, not the unused
height. Is there any way to make it do what I want?

I believe the 100% will be relative to the parent container
of the Object/Embed tag.
If the Flex app is in say, a DIV that is correctly sized,
then 100% will fill the DIV. So I think you will need to get your
div sizing dynamically. A CSS expression maybe?
Tracy

Syslogd process uses all available cpu & console app won't run.

I have a Mac Mini (G4 power PC) running 10.5.5. Just recently after several minutes the system never wakes. It just shows the SBBOD. All I can do is hold down the power button and reboot. When the system reboots, using the activity monitor, I see that the process named syslogd uses all available cpu. I can still do things, but the cpu is saturated.
I took a snapshot of the syslogd process, and I can post it here if anyone thinks it might help.
If I activate the console application, the window comes up then hangs with the SBBOD.
The syslogd process uses all available cpu right after reboot, and does so regardless of which user (including root) is logged in. Attempting to kill the syslogd process with the activity monitor does nothing

Thanks! It took a long time for the disk utility to fix the permissions, but as soon as it did, the logger process calmed down. Looking at the log file now, I see it was my McAfee virus scan causing the logger to flip-out.
I'm now looking for a new MAC anti-virus program.

CS2 Not reading all available fonts

Hello,
I just purchased a new Dell with an XP Professional Downgrade software package and have installed my CS2 Creative Suite on it.
When I open either Photoshop, Illustrator and InDesign, it appears many standard fonts (found in Control Panel / Fonts) , including 'Arial Black' are not available, though on my Adobe Acrobat Professional they are. (They are also available in my Microsoft Word Software).
I have read a few adobe trouble reports of this being a problem in InDesign, but the problems there are not what I am having.
When I open up say Photoshop and create a document, in the available fonts, my first choice begins with 'Agency FB', followed by 'Algerian', then 'Arial', and then 'Arial Rounded'. This is the same in Illustrator and InDesign.
Yet in Adobe Acrobat, missing fonts such as 'Arial Black', 'Arial Narrow' are available.
Also, in Program Files\Common Files\Adobe\Fonts ..... there are fonts there that are available in Adobe Acrobat, but not in my Photoshop, like Adobe Caslon Pro.
Anyone have any ideas as to why my Photoshop, Illustator or InDesign are not reading all available fonts?
Again, I transferred my CS2 from an older computer to a Dell that is equipped with Windows Vista Business with the Downgrade to Windows XP Professional.
I know CS2 is not compatible with Windows Vista, but I was under the understanding that the Downgrade to Windows XP Pro would give me a Windows XP Pro Operating system, avoiding the problem of my CS2 not being compatible with Windows Vista.
Everything else appears to be working properly (as far as I can see)
Thanks in advance for any help / insight / solutions.
Greg

Have you read this?
http://indesignsecrets.com/hotfix-corrects-arial-narrow-problem-on-windows.php
Bob

MBP not using all memory while rendering video

Hey,
When I do rendering in Adobe Premiere Por CS6, my Mac is not using all the available RAM: 2773 MB used....5416 MB free
Memory Pages:
                              1658 MB active....1099 MB wired
                              5420 MB inactive....11.2 MB free
it also says that:       3 swap files at peak usage
                               256 MB total swap space (20 MB used)
350 GB free storage space( total 750 GB)
I have a MBP (OS x Lion) late 2011 with i7 2.8 GHz and 8 GB RAM
Adobe Premiere Pro is set to use 6.5 GB of RAM but not even while working in the programme it has ever used that much of memory.
During rendering, it is the only app running, except for Google Chrome.
If this info is not enough, just ask what do you need to know...
PLEASE HELP, rendering takes forever.
Thanks,
kund

You never said what model Mac you have. Since this is the MacBook Pro forum, I assume you have some version of the MBP. 390% CPU would indicate CPU-boundedness for a quad-core CPU without active hyperthreading, or a dual-core CPU with hyperthreading active.
Given the high CPU usage and the low swap usage, it seems unlikely that memory usage is the problem, but I'm not a Premiere Pro user, so I couldn't guess what it.
You might try posting your question in an Adobe forum for Premiere Pro.

Can not use all the tools in my drawing markups any ideas on getting them to work?

Can not use all the tools in my drawing markups any ideas on getting them to work?

Hi tonys60181,
Could you please let me know what version of Adobe Acrobat are you using.
What all drawing tools are you unable to access?
Is this issue specific to one PDF file or all?
What exactly happens when you try to use any drawing markup?
Please let me know.
Regards,
Anubha

System Exec use all resources system if "wait until completion" is true !

Hello,
I use the function "System Exe" since a long time to launch various executables since Labview.
The " waint until completion " boolean is true, because I have to wait the end of the external executable to continue.
Big problem: the function " System Exec " use all resources system, by waiting for the end of the external program.
Is it a bug of this function ?
In my example, "System Exec" launches only the notepad (LV 8.2 on XP)
Thank you for your suggestions.
AC
AC
Attachments:
Process.jpg ‏86 KB
Bug system exec.vi ‏17 KB

Thanks to both for your speed.
In fact I had simplified my vi to target the problem.
I use System Exec to launch another executable, made possibly with labview, but with passage of parameter. (Ex: - " / string:init ").
In the literature Labview it was made with the method cmd / x / c start by putting twice the path of the executable.
In this method a waiting time in the recent system exec function was effectively missing.
But effectively, today, it is enough: "c:\myexe.exe" - " / string.init " to launch and to pass a parameter.
You have both reason and I thank you sincérement.
Very cordially.
Sorry for my English....
AC
AC

System not using all avail. mem.

Similar Messages

Maybe you are looking for