SYSTEM RECOVERY (F11) is inaccessible after dual-booting Windows 7 and Windows 8.

I dual booted Windows 8 with Windows 7 and now the RECOVERY partition (F is not loading upon pressing F11. It gives me the boot configuration data error. I have it marked as Healthy (Primary Partition) and I am able to access the files via. My Computer in both OS, but not through F11 System Recovery.
The bcdedit log is here: http://pastebin.com/b0Y5Hd1F
My partition letters:
C: Windows 7
D: Windows 8
F: RECOVERY
H: SYSTEM
In Visual BCD, One WRE is set to D: and the other is set to F:. Should i set both to F, which is the actual RECOVERY partition?
[2] The UEFI boot setup is unable to create HP_TOOLS parition because 4 partitions already exist. I don't remember having the SYSTEM partition earlier so maybe that repalced HP_TOOLS?
[3] When I try to create a recovey media, the orange circle filter keeps of going even after I have inserted the an external USB hard drive for it to detect. Does it usually take this long? I am guessing once the recovery media is made I could do system repair from there and get RECOVERY to work?

What is the p/n? Remove the battery and look for it. Post all alphanumeric characters.
CTO means configure to order. That means only you and HP know the notebook's configuration.
The problem you are going to run into is that there is a maximum of four primary partitions allowed by Windows. That is by design. It appears that you removed the HP_TOOLS partition, which was a requisite for the UEFI diagnostics.
Frankly it looks like what you will have to do is put the UEFI environment on a USB stick.
I would create the recovery media on a high quality 16GB USB drive.
The partition schema must be as follows:
1) C: (NTFS)
2) HP_Tools F: (must be FAT32)
3) RECOVERY D: (NTFS)
4) SYSTEM (NTFS) created by the Windows install process
I am not aware of a dual-boot or more schema that allows a UEFI environment with the Recovery Manager accessible from F11. I wish I had better news for you. Perhaps our forum Provost DavidPK knows how it can be done.
I do recommend that you copy the RECOVERY partition to an external disk for safety sake.
If you are able to boot into the recovery manager I strongly suggest that you create your recovery media. If you do not do that you will not have a copy of your operating system and drivers for a plan B. I did not go with the option you used and did not create problems to deal with later.
When I play around with my loaner notebook and configure it to dual/triple boot, I always install a different hard disk and put the original one aside. You can still return your system to its original configuration and then take the hard disk out and use another one to play with. I believe that would be the wisest path to follow.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Similar Messages

Dual Boot - Win 7 and Windows 10TP | HDD Prep and layout help

Hi,
This is my first time actually submitting a question in the forum. I've spent so much of my time on here reading for solutions but now hope for some help of my own.
My first attempt at installing Windows 10 Tech Preview (as an additional OS), rather than a 7<10 upgrade went ok until I completed the first platform update.
After that update, neither OS would load and using a Windows 7 recovery CD/start-up repair. It advised the MBR was corrupt.
I attempted many "fixed" found on this site, such as; CMD - MBR[repair,rebuild] etc. System restore was not an option due to the fact that when the RE booted, it could not load drivers for the HDD..possibly? Also, could not locate any existing
Windows installs.
I am now attempting to start again from square one.
I have since learnt the boot/volume table partitioning is different for each OS, MBR/MBT as opposed to GPT(GUID). Could this have caused corruption on the System boot volume (small vol, 600Mb approx).
Should I,
A. Perhaps create a VHD using disk manangment - if so, will the PC boot giving both OS options as previously?
Or B:
Someone please give me a better option :)
>
>
Many thanks in advance.
James

Hi, whatever you decide to do, It's best to install the oldest OS first, in your case, Windows 7. When you boot from your Windows 7 DVD, select advanced installation, from there you can setup your disk partitions for Windows 7 and another partition for
Windows 10. While your at it you can setup additional partitions for your data if so desired. Once you have your Windows 7 installed, you will need to boot from your Windows 10 DVD and select advanced setup so you can tell Windows 10 which other partition
to install into as not to wipe out your Windows 7 installation. Doing this will give you the multi-boot configuration and Windows 10 will install it's own Boot Manager. Hopefully you won't have the problem with the Boot Manager bug Windows 10 has. The
bright side is there is a work-a-round to that problem. Having a Multi-Boot setup gives each OS direct access to your hardware resources. A VHD setup is good for testing software and to see what an OS will be like to use, but suffers from
performance issues for some applications as it is an emulation. The up side of a VHD install, is your system is isolated from any problems you may have with a guest OS plus you can easily delete it if you do not like it or have problems with it. If run
into similar problems in a multi-boot scenario, you actually have to re-format and/or delete partitions and do a re-install to fix problems.

Dual-Booting Arch Linux and Windows 7

Hello,
I am attempting to set up a dual-boot configuration with Windows 7 (installed first), and Arch Linux. When I went to install, I read in the documentation that the AIF doesn't support installing GRUB to a separate partition other than the MBR on the drive. I want to install GRUB separate from the Windows MBR so I can use Easy BCD to chainload the two bootloaders (i.e. installing GRUB on /dev/sda5 instead of /dev/sda). I went through the installation process and tried to install GRUB manually via the instructions given in the documentation. But when I went to boot Arch, I was greeted with the GRUB shell instead of the boot menu. What did I do wrong? And is there any easier way to install Arch this way given that I do not want to overwrite the Windows bootloader? I went ahead and wiped the Linux partitions on my drive, so I am going to do the install again once I have some suggestions.
Thanks!

joshuawagner147 wrote:
hyperreal_logic wrote:
To the original poster:
If you want to chainload both Windows and Arch Linux using your preferred boot manager, you'd have to create a separate 'boot' partition when installing Arch Linux. When you are in the Arch installation, create a separate partition of about 500 MB, then create the root partition of whatever size you need, and then create swap partition if necessary. So your HD would resemble something like this: /dev/sda5=boot partition of 500 MB; /dev/sda6=root partition of ## MB/GB; and /dev/sda7=swap partition of (RAM * 2) GB. Then continue with the Arch installation procedure until you get to the end where you are prompted to install a boot loader. Choose GRUB, and install it to the 'boot' partition on /dev/sda5. This will allow you to chainload Arch via Easy BCD. What happens is Easy BCD will pass the message to GRUB on /dev/sda5, and GRUB will then load your Arch root system on /dev/sda6.
I hope this helps. I support your choice in using Easy BCD to chainload Windows and Linux. Software is, after all, about choice. Furthermore, you've presented a good reason to use Easy BCD as the main boot loader, which is to save you from unnecessary tinkering with the GRUB shell or Live CDs and whatnot. However, if you don't want to create the separate 'boot' partition, then you'll have no other choice but to use GRUB or syslinux on the MBR.
Thanks. Yes...I followed the procedure just like you described. I figured that my problem was that I didn't create a separate /boot partition, so I reformatted the partitions I created and redid the install. However, I was not able to install GRUB in the AIF; I had to reboot into the Live CD and install GRUB to my boot partition manually. All is good now as I have a working dual-boot now. Arch Linux has been a sort of learning curve for me, but I have gained valuable knowledge and experience by using this distro.
Yes. I didn't want to mess with GRUB or NTLDR. I know that reinstalling NTLDR is not that difficult, but I didn't want to mess with it at all. It just seemed easier to chainload GRUB to NTLDR using EasyBCD. I'm a sort of "distro-hopper" anyhow, and using this method allows me to cleanly remove any distro I install without having to mess with GRUB or reinstalling NTLDR.
Thanks!
Glad to hear! Yes, Arch Linux is a wonderful distribution, and one of my favorites. It's great for not-so-newbie beginners to learn from. pacman is one of my favorite package managers, as there is always the latest stable software available in the Arch repos. Glad everything worked out. Have fun with Arch!

Just loaded windows 7 on a macbook pro - how do you dual boot OS X and windows 7

Hi successfully loaded windows 7 and partitioned drive (I need windows for work Microsoft crm system)
All ok but a pain to have to keep logging off and on between OS X & Windows
I understand that there is a way to dual boot - I am running Snow Leopard on a macbook pro lap top OS x 10.6.7
Can anyone help please
Ian

You can install Parallels or Fusion, either will work. When you setup either Parallels or fusion you can tell it to use your already installed Boot Camp installation of Windows as its target guest operating system.
You would then just boot into OSx, start your VM (Parallels or Fusion), then you'll have access to both OSx and Windows without having to reboot.
I have this setup and two monitors. I have my Windows running on my external monitor and OSx running on my Macbook Pro monitor at the same time.
Beware that you will need to re-register Windows to get a second key. This is free and easily done either online or by calling the Microsoft registration number. The reason for needing a second key is that Windows, although only installed once in your Boot Camp partition sees the virtual hardware created by your virtual machine and thinks it has been reinstalled on a new computer.

Dual boot Solaris 8 and Windows XP

Hello. I currently have windows xp as my OS. I would like to install Solaris 8 as a secondary OS. I have a separate hard drive I would like to put Solaris on. My question is, will the solaris installation allow me to choose which drive to install solaris to? Also, how can I set up my system to boot windows if I do nothing, but boot solaris if I choose to? Thanks for any help, I'm new to solaris and to dual-booting.

Try this URL:
http://sun.pmbc.com/faq/9.html
Hope it helps.
Senthilkumar
Developer Technical Support
Sun Microsystems, Inc.
http://www.sun.com/developers/support

Ultra 40-M2: How to dual boot Solaris 10 and Windows XP?

I have an Ultra 40-M2 with 3 300-GB SAS drives.
First two drives I will use for Solaris 10 and mirror them using Solaris Volume Manager.
The 3rd hard drive contains Windows XP. I want to be given the option of booting into Windows. By default, I want to boot into Solaris 10.
How do I enable all this? Is there a configuration file I need to edit in Solaris to create this dual boot?

You don't need to configure GRUB. If the third drive is XP only, you can setup the boot order in your BIOS and when you boot the system you can hit the F8 key and select to boot from your XP drive.
It works very well for me.

Dual Booting Ubuntu Linux and Windows on a RAID 1 setup

Hi,
I just bought a Lenovo W530 with Windows 7 and two 500GB hard drives in a RAID 1 setup, is there a way for me to install Linux with dual boot while maintaing my RAID 1 setup?
Thanks.

Hi
Welcome To Lenovo Community
if you want both in a raid on two drives, there is no way simpler than using fakeraid.
Windows simply has only the fakeraid as a software raid and can't be run from a linux software raid. An Ubuntu 10.10 install to fakeraid is relatively simple but should not be undertaken without some understanding of what a raid install looks like or behaves.
As a starter, some simple rules have to be followed:
1) Install Win 7 first
2) If Win 7 occupies the whole raid drive, use Win 7 disk manager to shrink it to make room for Ubuntu.
3) Use gparted on a live cd to place all your unallocated space for installing Ubuntu into an extended partition. This will insure that you will not likely exceed the 4 primary partition limit and thus bar an Ubuntu install.
Once prepared as above you should be able to install Ubunto to the largest unallocated space, as long as the partitioner recognizes the raid (ie the win 7 partitions will show in gparted). You should plan to run the install from the live cd so that you have determined beforehand that 10.10 will run on your system.
http://ubuntuforums.org/showthread.php?t=1600991
Hope This Helps
Cheers!!!
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
How to send a private message? --> Check out this article.
English Community Deutsche Community Comunidad en Español

Dual boot with archlinux and windows issue

Hi again!
This is what i did from the beginning :
windows was already installed and then i installed archlinux after shrinking the windows partition . I made a partition for boot , one for swap and one for root(i wanted to do for home too , but only 4 primary partitions are allowed) . I made the boot partition bootable , and so was windows bootable and i got the message that there are two bootable partitions so it couldn't write the partition table . So removed the bootable tag from windows and left only the boot partition bootable . I then installed the grubloader to boot partition and then i edited that grubmenu and uncomment the part where windows was like it says in wiki. After restarting i could see the menu to choose between archlinux and windows , i chose windows , i succesfully logged in and after restarting again i couldn't see the grubloader and i automatically logged in windows .
Does anyone know what might be the issue ??
Thanks !
Last edited by shak (2009-03-27 20:20:30)

yes i only have one hard rive , i managed to find a solution not that elegant though , i 've installed acronis os selector from windows and i can choose between windows and linux with acronis on boot . If i choose linux i get to the grub menu and i can choose between arch linux and windows . So it seems that the grub menu is still there but it doesn't appear when i boot for some reason .
Last edited by shak (2009-03-27 20:34:40)

Dual boot arch linux and windows

I recently installed arch linux. However, I have a windows 7 installation on a separate hard drive (/dev/sdb), and it is not detected by grub. I have tried to use os-prober, and grub-mkconfig to generate my configuration file, but I think these programs are in grub2-common, and this conflicts with the package grub. When I do uninstall grub, and replace with grub2-common, I can generate the config file, but grub brings me to the grub prompt, and will not boot. Can I use grub-mkconfig without uninstalling grub, or do I have to create grub.cfg and edit it manually? Thank you in advance!

skunktrader wrote:
grub reads /boot/grub/menu.lst. You need to edit this file manually to add windows 7
Read this
It works! You are a genius!!!!!!! Thank you so much!!

Dual booting win 7 and arch: cannot install grub to partition

I have read the arch wiki page on dual booting and several other sources on line, but I am still struggling to get this to work.
I am trying to dual boot arch and windows 7 on my lenovo ideapad s205. the machine comes with windows 7 pre-installed.
I shrank the win 7 partition and added an extended partition with 3 logical partions for /boot, swap, and /.
I am able to install and run arch by installing grub to the mbr. when I do this, though, I cannot boot windows. (the windows section of grub menu.lst is uncommented and points toward hda0,0. I have tried hda 0,1 as well).
I have also tried to use the windows boot loader to load arch, as described in the arch wiki page on dual booting. The problem here is that, taking this approach, I should install grub to my /boot partition, but when I try to do this, the installer only allows me to install grub to sda or sdb (the usb stick).
I have read that grub should be able to boot linux from a logical partition. Is this so?
Is there something wrong with the arch installer that it is not giving me the option of installing to a partition rather than the mbr, or is this a problem with my partition scheme, or something else?
I am tempted to remove lenovo's recovery system, but on the other hand, I have already needed to use it several times while monkeying around with installing arch.
Thanks for any help.
UPDATE:
I now have the laptop dual-booting win 7 and arch. My solution ( adapted from here: http://helms-deep.cable.nu/~rwh/blog/?p=177) was to:
1. installed arch on the partitions I had created for it, but skipped the "install bootloader" stage.
2. in win 7, I downloaded and installed EasyBCD and made an entry for arch in it. I checked the option to "Use EasyBCD's copy of GRUB"
3. When I restarted, I got a grub error because the entry in grub's menu.lst was pointing at the wrong partitions for the kernel and root.
4. So I went back into the arch live disk, mounted the boot partition and edited menu.lst.
Now when I start the laptop, the windows boot loader starts and I can choose between win 7 and arch. when I select arch, grub4dos starts and gives me the option to start arch. this is not particularly elegant (nor is it fast), so I think this solution is less than ideal, but it does work.
I'd be interestd in any thoughts about what went wrong and what a better solution would be.
thanks.
Last edited by ratchet (2011-10-10 19:09:16)

ratchet wrote:II am able to install and run arch by installing grub to the mbr. when I do this, though, I cannot boot windows. (the windows section of grub menu.lst is uncommented and points toward hda0,0. I have tried hda 0,1 as well).
Is this a typo in your post or how it was in menu.lst? Surely it should be hd0,0 and not hda0,0? The entry I have in my menu.lst is as follows:
# (2) Windows
title Windows
rootnoverify (hd0,0)
makeactive
chainloader +1
What was yours?
Last edited by JHeaton (2011-10-10 20:18:22)

Dual boot for lion and SL

BHow do I set up the dual boot for Lion and snow leopard oon the same internal hard disK
What does Time machine do under the dual boot?

I am also considering putting Lion and SL on separate hard drives.
Since this is an iMac forum, I assume you will use an external drive as the second drive. Use one that connects via firewire, not via USB.
Both on a single drive -
OK. Doing it on a single drive means you will need to partition the internal drive. Although this is straight forward, it is always best to back up the existing drive first, just in case. It's a good idea to have a backup on a different drive, anyway.
To do that, clone the entire internal drive to the external drive.
I would suggest, though, that you first partition the external drive. I would suggest four equal-size partitions, provided the drive is big enough - at least 1.0TB, though a 2.0TB drive might be better. You can use OS X's disk utility to do that. Go to the Partition page in Disk Utility, select your external driv in the list on the left, then use the Partition Layout menu to select the number of partitions. Set the format to Mac OS Extended (journaled) GUID for all partitions. Click the Apply button.
The easy way to do the cloning is to use a cloning utility such as Carbon Copy Cloner. Clone the entire internal drive to one of the partitions on the external drive. Then test boot to it (use Startup Disk in System Preferences to do that) to verify the integrity of the clone. At that time I would suggest you change the background design/picture for the desktop to aomething other than the one used on the original drive - this can be a handy visual reminder of which volume you are booted to.
Then add a partition to the internal drive. To do that, run Disk Utility. Go to the Partition page, select your internal drive in the list on the left, but do not use the Partition Layout menu this time. Instead, click the existing volume in the graphic display, then click the plus ("+") button underneath that display -
This will add a partition without erasing the existing information - i.e., the drive will end up with two partitions, one of which will contain your original boot volume.
Use Startup Disk to re-select your original boot violume, and restart back into it.
Now, clone the original drive again using CCC, but this time to the second partition of the internal drive, the one you just added.
Boot to that freshly cloned volume to verify it. Then, while still booted to it, install OS X 10.7 Lion onto it.
This will result in your original Snow Leopard on the first partition of the internal drive, and Lion on the second partition of the internal drive.
The external drive will have Snow Leopard on one partition, one partition will be empty (available for a clone of Lion if you wish, or use it for extra storage). The remaining two partitions can be used for Time Machine backups - one for Snow Leopard, one for Lion.
If you want to have each OS on its own hard drive, then you can use the first clone of Snow Leopard to the external to be upgraded to Lion, or upgrade the orignal on the internal drive to Lion. Be sure to boot to the volume to be used for Lion before installing it so that Lion is installed onto the correct boot volume.
You can then use the empty partition on the internal drive as the backup (or Time Machine) volume for the OS on the external drive, and vice versa. In this arrangement you may need only partition the external into two volumes.
If you have a different scheme in mind for partitioning, feel free to do that. I don't use Time Machine, so don't have the need to make space for it. Carbon Copy Cloner can be used to do incremental backups after the initial backup - but I don't use that, either. I'm old school - after the inital cloning for backup, I do manual backups of files on the fly.
Comments -
* I would suggest keeping both Snow Leopard and Lion on the internal drive. Reason - even though firewire 800 is fast, it is still noticeably slower than an internal drive. OS's on an external drive will run slower than those on an internal drive.
• I don't like the concept of Time Machine. Amongst other things, it seems to want more space on the target volume than it actually needs; and it is not a bootable replication. A clone of a bootable volume is bootable.
• It was just a few days ago that I went through the same process as you are planning. One slight difference - I used a 1.0TB external partitioned into 3 equal volumes, since I had no need to allow space for Time Machine. I have Snow Leopard and Lion each on its own partition of the internal drive; and cloned backups of each on the external drive, plus one GP partition on the external drive.
• If you have not yet downloaded Lion, be prepared for it to take a while; it's almost 4GB in size. Probably be a good idea to defeat sleep for the duration.
• Cloning takes a while, but not that long - it took 30 minutes to clone 45GB to the external drive, and 45 minutes to clone it to the second internal partition.

Dual boot kali linux with windows 8

i have ideapad y510p and i want to dual boot kali linux with windows 8
i want a full guide to do it please !!help!!!

Hello,
if you got problems with the kernel, you can try backbox-linux. The kernel there is newer. It is based on Ubuntu 12.04 LTS.
Have a nice day
thoschi
LENOVO IDEAPAD Z710 59403383,i7-4700MQ,8 GB DDR3-RAM,1.920 x 1.080 Pixel,NVIDIA® GeForce® GT 740M,Hybrid (1 TB S-ATA + 8GB SSD)

Can I dual boot snow leopard and mountain lion if I've installed boot camp on my drive

Can I dual boot snow leopard and mountain lion if I've installed boot camp on my drive

Yes as I said before. If your model Mac came with Snow Leopard and you are now running Mt Lion and have Windows installed in a Boot Camp Partition all you have to do is make the Mt Lion partition smaller, take the free space and make it another Mac partition and you should be able to install Snow Leopard into that partition.
I have Snow Leopard, Lion and Mt Lion installed on my MBP. No Windows in a Boot Camp partition because I run Windows XP in a Virtual Machine on both Lion and Mt Lion.

Can I dual boot Mountain Lion and OSX10.6.8

Can I dual boot Mountain Lion and OSX 10.6.8. I just upgraded to Mountain Lion and my InDesign CS2 no longer works. If yes, how does one do it.
Thanks all,

Yes, as long as your computer shipped with 10.6.8 or earlier. Insert the Mac OS X 10.6 DVD, restart with the C key held down, and install it onto a separate partition or drive; if you use Boot Camp, repartitioning the internal drive may disable it.
(75122)

Can I erase the boot camp partition and dual boot snow leopard and mountain lion instead

Can I erase the boot camp partition and dual boot snow leopard and mountain lion instead

Please don't double post. Look at your other thread.
If you want to get rid of Windows and the BC partition use the Boot Camp assistant program to remove the Win/BC partition. Don't do it manually with Disk Utility Use the BC A program.

SYSTEM RECOVERY (F11) is inaccessib​le after dual-booti​ng Windows 7 and Windows 8.

Similar Messages

Maybe you are looking for

SYSTEM RECOVERY (F11) is inaccessible after dual-booting Windows 7 and Windows 8.