System restore is not working

System restore is not working for my Itouch. I am getting a picture of a white cord and and arrow pointing to Itunes logo... any suggestions?

It sounds like there is definitely a system problem. The whole OS seems to be messed up.
Do you have an MS Windows 7 disk?
In such case you could start the Windows 7 Startup Repair process using the MS Win 7 disk.
Boot from Win 7 disk, after the temporal files has been load, you should get and window where you could choose between the OS installation and other options. The second option called Repair you Computer is the one which would be needed to get the system repaired.
Then wait for System Recovery Options to locate Windows 7 on the HDD.
Then choose the Windows 7 installation and then the next window should appear providing the option to repair the system Startup Repair
But in case this workaround would not help you, the system should be reinstalled once again using Toshiba Recovery disk

Similar Messages

System Restore does not work (Windows 7)

I believe that my internal wireless network card has died although the laptop is only 8 months old, but that's another issue.
I'm running Windows 7, and I tried to have system restore backup to a few days ago. There have been no changes to the computer in this time other than Windows update. After performing system restore and rebooting, I have a message that system restore was cancelled because there was a file in use. It suggested I disable anti-virus protection. After disabling that, I tried system restore once again. The computer seemed to be doing it right, but after reboot, I got the same message that it could not be performed due to a file in use.
I've turned off everything I can think of, does anybody know why might be causing system restore to stop and how it could be corrected?
Thanks

If you cannot do a System Restore from the Recovery Environment (as Archie suggested), then probably the restore points have become corrupt. That's not uncommon.
To repair that, turn System Restore off and then on again. Unfortunately, that removes all the previous restore points.
Turn System Restore on or off
If you post again, tell us which computer you have.
-Jerry

System restore does not work!

I am running Windows 7 upgraded from Vista and I am having issues in the little flag that pops up in the task bar on the right side.
It says that disk errors are detected, when i try to fix it nothing happens. I tried to restore my computer and I keep getting this message that
"Windows has detected file system corruption on (my hd). You must check disk for errors before it can be restored"
I go to run the disk check and when I do not have automatic fix it actually scans, but tells me after a while that I need to click the automatic fix file system.
I do that and it says "Windows can't check disk while in use. Do you want to check for hard disk errors the next time you start your computer?"
I click schedule but nothing happens when computer restarts.
Any help would be appreciated.

Ill post you some screen shots can you over here ill try to link them.
I go to restore 1.
http://i25.tinypic.com/2wdxboz.jpg
2. I go next and select a point to restore
http://i28.tinypic.com/1zwhopz.jpg
[IMG]http://i28.tinypic.com/1zwhopz.jpg[/IMG]
3. I get error
http://i26.tinypic.com/29vn95.jpg
[IMG]http://i26.tinypic.com/29vn95.jpg[/IMG]
4. I check for errors and get this
http://i28.tinypic.com/64nl3b.jpg
[IMG]http://i28.tinypic.com/64nl3b.jpg[/IMG]
5. the schedule thing pops up
http://i32.tinypic.com/11m84nk.jpg
[IMG]http://i32.tinypic.com/11m84nk.jpg[/IMG]
MarantzI tried that earlier and it still did not run after restart.
I searched these forums and they had a vista fix I tried to use that since my original windows was vista but that didnt work for me. In that they had the chkdsk r and stuff nothing worked

Hello, all of a sudden I fell down my system and completely erased all bookmarks. Your progress with restoration does not work, send me ansver,please

Hello, all of a sudden I fell down my system and completely erased all bookmarks. Your progress with restoration does not work, write me of bookmarks could not be loaded. Please advice on everything because I came and they seriously need it.

Did your computer crash or did Firefox crash causing the loss of the bookmarks?
You can check for problems with the places.sqlite database file in the Firefox Profile Folder.
*http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
*https://support.mozilla.org/kb/Bookmarks+not+saved#w_fix-the-bookmarks-file
See also:
*http://kb.mozillazine.org/Lost_bookmarks
*http://kb.mozillazine.org/Firefox_crashes
*https://support.mozilla.org/kb/Firefox+crashes

HP Pavilion dv6-6181TX. System Recovery is not working From HP Recovery Manager.

HP Pavilion dv6-6181TX
Product No. A3U49PA
Genuine Windows 7 Home Premium 64
(but i upgraded it to windows 7 ultimate)
System Recovery is not working From HP Recovery Manager. so i cant restore my laptop to its original factory condition. (Genuine Windows 7 Home Premium).
so when i restart my computer and press Esc and then choose F11 i get this message :
"Windows failed to start. A recent hardware or software change might be the
cause. To fix the problem:
1. Insert your Windows installation disc and restart your computer.
2. Choose your language settings, and then click "Next."
3. Click "Repair your computer."
If you do not have this disc, contact your system administrator or computer
manufacturer for assistance.
File: \Boot\BCD
Status: 0xc0000225
Info: An error occured while attempting to read the boot configuration data."
i saw this from the forum
http://h30434.www3.hp.com/t5/Notebook-Recovery/Hp-recovery-manager-problems/m-p/2395473/highlight/tr...
Had the C partition been split/shrunk to form a new partition previously?
Does disk management show the HDD as basic or dynamic? (Start>Right-click Computer>Manage>disk management on the left).
If it has been switched to dynamic (Windows does this automatically when more than 4 partitions are present on the disk), then the F11 recovery partition won't function until it is restored to basic, but I would like to confirm that is the scenario before providing those steps.
The Disk management shows that my HDD as Dynamic, what should i do then if this is the case and the possible solution to my problem?
please help me & Thank you for your time,
This question was solved.
View Solution.

If you have more than 4 partitions you will need to delete the extra partition/partitions, then convert the hdd back to Basic.
Older versions of Partiton Wizard Free work:
http://www.sevenforums.com/tutorials/26829-convert-dynamic-disk-basic-disk.html
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

Not able to sign into Blackberry Protect. Backup and Restore function not working. "Your device isn't associated with a Blackberry ID"

Not able to sign into Blackberry Protect. Backup and Restore function not working. Message is: "Your device isn't associated with a Blackberry ID." My Blackberry Messenger and Blackberry World is working fine so I am sure its not an ID issue on the phone. I can sign into Link, Blackberry.com and Protect. I see my device in Protect but cannot send messages or view it on a map. Times out with cannot reach device message. BB Protect on Device has a swirling circle beside the on/of switch. Cannot turn off.
I have deleted Link and re-installed.
I have reset phone to default(factory) and signed in.
OS level is 10.2.1.3062
BB Link is 1.2.3.56
Solved!
Go to Solution.

I managed to figure this out myself. I had to delete the device from the Blackberry Protect website. protect.blackberry.com. I wiped my device again and signed in with my Blackberry ID. I dont know if the step of wiping was necessary as I did not try my backup with the current configuration on the device following the delete. Restore is in progress for me!

System.out.println not working in Tomcat-4.1.x

System.out.println not working in Tomcat-4.1.24. Any settings has to be enabled??? I am using tomcat for Solaris

I think u can use ServletContext.log() to output info instased.

HT1414 my ipad shut off while using my battery is charged and i did itunes restore did not work what now

itunes restore did not work what do i do now

Error 13, 14, 35 and 50 (or -50)
These errors are typically resolved by performing one or more of the steps listed below:
Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.
Put a USB 2.0 hub between the device and the computer.
Try a different USB 30-pin dock-connector cable.
Eliminate third-party security software conflicts.
There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.
Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.
Try to restore from another known-good computer and network.
The copy above was copied from this website.
http://support.apple.com/kb/TS3694#error14

Systems preferences does not work

My Systems Preferences does not work, either reminders and messages... since Mavericks(10.9) Programs do not respond and Macbook air is not responding.... Help.....

Well, you are certainly correct that the fact that the "wired" machines work sure doesn't rule out a faulty router....But that's why (as part of a process of elimination troubleshooting scheme) I hooked up my old Linksys Router, and got the same results. Now...What are the odds of 2 separate routers acting the same way? Especially when both worked fine on my TIPB and even on my MBP until a few months ago. Plus, my 12 year old son can pull a wireless signal from the router on his console games (xbox360, Wii, PS3) with no problem
Believe me, my first thought was to go out and buy another router, but when I swapped routers and got the same problem, I began to look elsewhere, eventually coming here for help and knowledge.
I did the SMC reset to no avail. I'm not sure about the stuff in System Configuration....By "pull" do you mean to delete all the files in this folder? Move them to a temporary folder? Should I just deal with the folders that have "IP" in the "bundle" file name?
Any help would be greatly appreciated!
G5 Dual / G4 TiPB / MBP 2.0 / 2.0 Mac OS X (10.4.8) 23" Cinema Display and 8 gig on G5 Dual
G5 Dual / G4 TiPB / MBP 2.0 / 2.0 Mac OS X (10.4.7) 23" Cinema Display and 8 gig on G5 Dual

HT201412 Restore did not work.The ipad mini says it is disabled, connect to itunes.When connected, it says that it is locked! After Recovery/Restore completed, device still malfunctions. The slide image keeps dancing around the screen.Device types on its

What if you have a situation where Restore did not work. I do. The ipad mini says it is disabled, connect to itunes. When connected, it says that it is locked! I have tried using Recovery/Restore but after it completed, the ipad mini still malfunctions. It does not allow you to start the device. The slide image keeps dancing around the screen. The opening page keeps changing in size and the keyboard types on its own! What can be done to fix this????????

Maybe a reset would help, to be followed by trying the recovery again.
To reset, hold the on/off and home buttons together for about 10 seconds till the Apple logo appears. Then do the recovery.
If this doesn't solve it, I recommend visiting an Authorized Apple Service Center.

In my system facebook is not working plz hepl me out fast

sir in my system Facebook is not working plz sir help me out fast plllzz

At 1st click the Facebook
button in the toolbar
and select Remove
from Firefox.
Then You will see a
confirmation dialog
asking if you are sure
you want to remove
the feature. Click
Remove Facebook
Messenger to
completely disable it.
After that Messenger should be
completely disabled.
Then Log in to your
Facebook account at
facebook.com and Visit facebook.com/
about/messenger-
for-firefox
then Click the green Turn
On button. The
messenger sidebar
will open and
confirmation
message will be
shown.and Click OK in the
confirmation
message to turn the
feature on.

Adobe Flash will not update to a W-2000 system and will not work? Is there a fix? Mozilla has disabled Flash. Do I have to go back to Explore?

Adobe Flash will not update to a W-2000 system and will not work in Firefox? Is there a fix? Mozilla has disabled Flash. Do I have to go back to Explore?

have you tried to install flash
restart imac
go to web site which require flash

HT1766 I backed up to my PC and attempted restore but I keep getting an error message that "iTunes could not restore the iPhone because not enough free space is available." I have a 32GB iPhone; only 13GB used!!! HELP! iCloud backup/restore did not work

I backed up to my PC and attempted restore but I keep getting an error message that "iTunes could not restore the iPhone because not enough free space is available." I have a 32GB iPhone; only 13GB used!!! HELP! iCloud backup/restore did not work either! How can I resolve this problem to restore from back up.

If you're not a developer then you really should not have upgraded.
I'm unsure how you can fix this as you have already done a back-up on iOS 7 and apple don't support firmware downgrades.

DB Restore does not work on MSSMS 2014 under WIndows8.1

When attempting to restore a DB which was backed up on a different machine (same names but SQL EXPRESS 2012) under MS 2014 running on WIndows 8.1 into a SQL Express DB, the following happens:
1. Open Restore task
2. Select Device to get 'Select backup devices"
3. Invoke "Add" and expect to see a browser. Instead, a backup file location is indicated and no browsing is permitted in the "Locate Backup File" Even when the path and file names are just typed in, the Restore will not work.
Any help is appreciated.

Hi,
SQL Server does not allow you to restore or attach a database from a higher version of SQL Server to a lower version of SQL Server in your case from SQL 2014 to SQlL 2012, however you can generate script in SQL 2014 and execute it on SQL 2012.
How to migrate a SQL Server database to a lower version
Please mark solved if I've answered your question, vote for it as helpful to help other users find a solution quicker
Praveen Dsa | MCITP - Database Administrator 2008 |
My Blog | My Page

After system restore CS3 stopped working and can not be uninstalled

I did a system restore (W7) and my CS3 apps stopped working with the message "Licensing for this product stopped functioning. Currently you cannot use this product. Solve this problem by uninstalling and reinstalling or contact support." I tried to uninstall but the installation manager returns a list of applications with red X and "unsuccessful" next to it. Reinstalling it from the dvd returns: "Installation error, can not continue. Contact support. Internal error 2739". I do not really want to reinstall the whole system since other Adobe applications (PS CS6) work just fine.

Try using the Cleaner Tool
Adobe Creative Suite Cleaner Tool
helps resolve installation problems for CS3 thru CS6 and for Creative Cloud
http://www.adobe.com/support/contact/cscleanertool.html

System restore is not working

Similar Messages

Maybe you are looking for