System temperature at 90C in Portege R700

When I switch on my Portege R700 and immediately open the Toshiba PC health program (monitoring the sensors) it shows the CPU temperature to be very low, of course, while the System temperature is already at 90C.
As a consequence (I think but I might be wrong) the fan spins at almost maximal speed.
The situation does not change in time: the CPU temperature stays typically under 40C, System temperature at 90C, fan always spinning fast.
Is this normal? The Cooling test program says everything is fine.
Daniele

Hi
First of all I have to say that many 3rd party tools does not read the temperature values correctly. If the notebook does not shut down automatically, then the temperature is not too high. There is a internal hardware protection which would shut down the notebook to prevent the hardware from damage.
But of course, the fan might run faster if the temperature is higher. This is nothing unusual. As suggested by Jeka. Try to clean the cooling vents using compressed air spray.
In very rare cases the temperature might be higher if fresh air cannot circulate due to clogged cooling grilles.

Similar Messages

  • Portege R700 - after Java update UMTS/3G is not found

    Portege R700 Win 7 Prof.Pro x64.
    After updating from java 6u20 to 6u23 the wireless manager isn't able to find the UMTS/3G device. Afterswitching back to pref system recovery point, the UMTS/3G device was detected by the wireless manager correctly and everthing works fine, but the recovered java 6u20 doesn't work in the system and even in the browser (ff 3.6.13 32bit).
    What can I do to get back correct function?

    Hey,
    >but the recovered java 6u20 doesn't work in the system
    What does this mean exactly? Do you get an error message?
    Maybe you have to update the 3G driver with new Java version. Have you already tried that?

  • Portege R700 -- disabling Intel AMT in BIOS causes fan to run constantly

    I recently purchased a Portege R700-1321, which shipped with BIOS 1.40.  I'm running Windows 7 Pro x64.  I have attempted to disable Intel Active Management Technology (AMT) on this machine by going into the ME BIOS (via ctrl-P at bootup), setting an admin password, and then disabling ME completely.  However, when I reboot after disabling ME, the fan starts to run at high speed and runs continually so long as the machine is powered on.  Re-enabling ME in the BIOS and rebooting again causes the fan to behave normally.
    I believe this is a BIOS rather than Windows problem because upon booting the machine, the fan steps up from low to high speed over the course of about a second before the Windows startup screen appears.  Windows appears to be fine despite the continually running fan, so AFAIK this is not the freezing-up issue that has been reported for R700s, despite the similar involvement of the fan.
    Is anyone else seeing a similar issue?

    I noticed that when battery is charging the miniPCI temperature spikes to 50 degrees. Unplugging the AC or reaching the charging threshold causes sudden drop in the temperature. The interesting thing is that the minipci sensor is near the southbridge (near the ram) and the battery sensor itself stays stable at 30 degrees. 

  • Portege R700 - freeze & fan

    Hi,
    I've a two day old Portege R700 and it has developed a freeze and fan issue. Actually it kicked in on day one.
    Basically the screen freezes and the cooling fan kicks into gear and nothing else responds until you do the off & on again thing. Its happened a couple of times now on two different days.
    Any ideas?
    Send it back?
    Download an amazing bit of software I currently know nothing about?
    Persevere on the toshiba website until I find out how to contact Toshiba directly rather than you good folk?
    Ignore it and hope it goes away?
    Any advice welcome. Though please make it as basic as possible as I'm a bit of a novice when it comes to the technical stuff.
    R
    (Just in case you're thinking about overheating, based in the UK and it isn't a hot day and there is free air circulation around the laptop. The second freeze happened after only ~2h30 of use.)

    Hi,
    Apologies for the lack of details & thanks for taking the time to respond.
    OS:
    Windows 7 32 bit.
    CONFIG:
    As it originally was, I have made no modifications other than loading any updates when I first switched the laptop on.
    SOFTWARE:
    Office professional 2010
    itunes
    Mendeley (An academic paper management system)
    internet explorer 8
    (+any prepackaged stuff that came with the laptop that I haven't opened or explored.)
    McAfee antivirus
    POWER SUPPLY:
    So far I've only run the laptop off the AC power supply. So I do not know if it will also happen on battery power.
    On a positive note, it hasn't happened for the last 3 hours. I will however hunt out the nearest authorized service and ask a few questions.
    Thanks.

  • Portege R700 - Missing rubber stopper, replacements?

    Hi all
    I have a Portege R700, and the rubber stopper on the bottom left hand corner, the one nearest the intake fan, has come off.
    Other than the aesthetics, this has more serious consequences, as it is impeding the airflow for the system, and potentially leading to higher temps and/or throttling.
    My question is, is it possible to get replacements?
    Thanks in advance

    I dont know for sure but I think it can be replaced. The question is where you can get it.
    Try to contact nearest Toshiba service and ask if they can order it for you. To be honest I dont think you can buy it as separately part.

  • Portege R700 - Issues with video playback with resolution over 360p

    I've got this video playback issue from day one. While for instance on YouTube, videos with resolution above 360p freeze up while the sound is ok.
    I've contacted Toshiba through which I got a linke to the latest bios and drivers. After the upgrade issue persists. I sometimes get a green screen while watching flash video as well. I'm guessing this is a graphic card hardware issue. Any ideas? Thanks! (Portege R700 19L, win7 pro 64)

    Hello
    Have you tried watching videos in high performance mode and tested different Internet browsers?

  • Portege R700 - fonts in main window of AuthenTec Truesuite has changed

    Hello,
    I have pre-installed on my Toshiba Portege R700 AuthenTec Truesuite version 3.0.1.149. After couple of days of good performance the font from the main window has changed becoming impossible to read. Probably I change some settings in Windows and also this font changed because for sure I did not change anything in your application. Having in mind that my OS is Windows XP Professional, SP3, pelse be so kind and help me with a solution to revert to standard fonts.
    I have deinstalled application, cleaned registries, reinstalled application from software package downloaded from Toshiba site,
    thank you,
    Best regards,
    Cristian

    Can you please tell me which language do you use?
    The whole story is somehow strange. I use Toshiba notebooks almost 10 years, have installed different stuff numerous times but I never saw something like this.

  • WXP Sound Driver install problems on Portege R700

    Hello
    Have installed Windows XP on a new Portege R700 PT310E. Have managed to reinstall all the other drivers but cannot for the life of me get the sound drivers installed. Installed the sound drivers from the website but still no audio device is detected. The unknown device in device manager is showing as VEN 8086 DEV 3B56 but theres not really any useful info on the PCI database.
    Any suggestions on how I can sort. Cost me a few frustrating hours today !!
    Cheers

    Do you have XP Service Pack 3 installed?
    You must have SP3 installed for the HD Audio drivers to work properly. SP3 added low level HD Audio support.
    http://www.microsoft.com/downloads/en/details.aspx?FamilyID=5b33b5a8-5e76-401f-be08-1e1555d4f3d4&displaylang=en
    Also ensure you have installed the Intel Chipset Utility.

  • Portege R700 - Installed Power Saver on Windows 7 64bit

    Hi,
    I was looking for a way to reduse fan noise on a Win7 Portege R700-174 and read to install "Power Saver" from the Toshiba support site.
    Installation was OK, but I cannot use ist because Common Module is not installed. I get an error "Code: 0x2". I already understand that "Power Saver" and "Common Module" is not intended for windows 7. Why have I been able to install it anyway?
    Now when I try to remove "Power Saver" i get yet another error and uninstall fails.
    What can I do? Any help is appreciated!
    Regards
    Michael

    Hey,
    Toshiba Common Modules and Power Saver are designed for Windows XP only! This software isnt compatible to Vista and Windows 7. In this case you have to install Value Added Package.
    Anyway, not its too late and you must remove the installed software. If you get an error while uninstalling I would recommend using CCleaner to remove the programs. CCleaner can also uninstall all software that you have installed and its freeware tool. Do a Google search to download it and try uninstalling the Toshiba tools again.
    Check this!!!

  • Portege R700 - fonts in main Window has changed

    Hello,
    I have pre-installed on my Toshiba Portege R700 AuthenTec Truesuite version 3.0.1.149. After couple of days of good performance the font from the main window has changed becoming impossible to read. Probably I change some settings in Windows and also this font changed because for sure I did not change anything in your application. Having in mind that my OS is Windows XP Professional, SP3, pelse be so kind and help me with a solution to revert to standard fonts.
    thank you,
    Best regards,
    Cristian

    Hi
    I assume you are speaking about the fonts in the Internet Explorer window.
    Right?
    Please check the option View in the menubar. Zoom should be set to 100% and Textsize should be set to medium.
    Furthermore you can check the settings in control panel -> display -> Appearance tab
    There you will find option called Font size. In my case its set to Normal.
    Try it out.

  • What exactly does "system temperature" mean in bios?

    Hi.
    I have a Ne0 FIS2R PCB 1 with frequent game crashes & i recently installed asetek´s watercooling kit wich is cooling the cpu & Northbridge.
    The bios says the CPU is 34 Degrees Celsius which is perfectly fine.
    But the system temperature says 52 Degrees.
    Is system temperature the air temperature inside the case? The manual doesn´t say.
    Thanks in advance.
    /Owe
    sys spec:
    MSI Ne0 FIS2R
    P4 Northwood 3,2 GHz
    2*512 Dualchannel PC3200 PNY memory
    Sapphire Radeon 9800 Pro
    Soundblaster Audigy 2 ZS

    The sys temp in the basic temp arround your mobo. (or Inside you case)
    That's kinda warm, mine is 35deg/ c and the air temp is 23.

  • Portege R700-15Q- Usage of SSD as 2nd drive

    Hi,
    I would like to install a small SSD as a second drive in my r700-15q, in order to experience the SSD renaissance.
    I see others have done this using a caddy that is installed in the optical drive bay.
    My laptop does not come with an optical drive, or a bay for an optical drive. It only came with an internal 7200 RPM traditional drive. here is the full spec http://www.toshiba.co.uk/discontinued-products/portege-r700-15q/
    Is there anyway to install a second drive in my laptop (r700-15Q)?
    In the worst case, is there enough connectors and space to fit a small SSD inside using electrical tape!
    Thanks!

    Hi MasterG,
    Thanks for that!
    That link you found nicely details how to replace the main HDD. But, my question is more complex than a normal HDD replacement. As SSD is relatively expensive per MB, I would rather have a 32GB SSD drive installed for OS, applications, and some workspace, and keep my existing hard drive just for storage.
    Your confirmation that the physical size of the laptop is the same with and without the optical drive, would lead me to hope that I can install a drive in the space that is normally occupied by the ODD.
    My proposal is to remove all the screws and taking the complete back off the laptop (and/or maybe front), to access the physical space where the ODD normally is, and try to put a second drive in that physical space. In the worst case you electrical insulating tape, but maybe managing to mount a caddy for the drive somehow.
    Four issues I see
    1. is there physical space
    2. is there a method of securing the drive in place (less of an issue with SSD I imagine)
    3. Can I get a sata cable to the new drive location
    4. Can I get power to the new drive location.
    Message was edited by: SSDperformance change three to four

  • Portege R700 - original recovery image re-installation failed

    Hello
    I have a Toshiba Portege R700 for years.
    As i already have some trouble, i did a reinstallation few years ago, from recovery partition. Directly.
    But, few days ago, i had some issues with my portege.
    HDD seems to be broken as it make some noise and was really, really, really, ..., really slow.
    So, after making some data backup during hours and hours (remember, it was really, ..., really slow), i lauch a complete re-installation from "recovery partition". It seems to be good, but .. never finished the process, with same HDD noise, and again slow HDD I/O.
    OK, my own diadnostic: change HDD.
    This done, and using the Toshiba recovery DVD just bought (yes impossible to find the earlied burn DVD), i have ... the same issue. The recovery process does not end even if 'im waiting for days ...
    And i have the same HDD noise. With the new one!!
    So having a MSDN licence, i installed a Win7 Pro 32bits, but not the Toshiba one.
    And it's running for days without any issue!
    But i have to reinstall all drivers, and software delivered by Toshiba.
    Obviouly i will prefer to find what is the exact issue with this Portege, and reinstall the Toshiba version of Windows 7 Pro.
    So, if someonre read the story until, the question is: ANY IDEA?
    How to make a HW diagnostic? How to identify the exact problem?
    Thanks for your help.
    Jol

    Hi Dr Lamp.
    Remember that i
    - did a successfull recovery from recovery partition few years ago
    - tried 2 recovery recently
    try 1, from recovery with initial HDD.
    I'm not REALLY sure, but i think that the recovery failled during step "recovery image installation from copied data step 50/52"
    I'm not sure.
    As it take hours during this step, if it go to the next step or not, as i let it run for hours and hours (yes, i'm persistent)
    try 2, from original Toshiba DVD i ordered (35)
    I'm sure it fail during an additionnal step you forgot.
    Because after "installed OS will be prepared for usage", which configure a lot of things using numerous reboot, there is the final step which is "first launch of win7"
    Note that not the exact term, but is something like that.
    Thanks for your help
    Jol

  • Power manager improve system temperature rating

    Hi
    I am running my t61p on Windows 7. How can I improve my system temperature rating?
    AT the moment it is stuck at 5/7 green dots. I cannot find any options to improve this. Is it actually possible to change this? If so, how is it done?

    Hello adante,
    please try to click on you battery symbol once, the a menu will open, a slider you can move it to the left, then power consumption will be reduced to minimum.
    Follow @LenovoForums on Twitter! Try the forum search, before first posting: Forum Search Option
    Please insert your type, model (not S/N) number and used OS in your posts.
    I´m a volunteer here using New X1 Carbon, ThinkPad Yoga, Yoga 11s, Yoga 13, T430s,T510, X220t, IdeaCentre B540.
    TIP: If your computer runs satisfactorily now, it may not be necessary to update the system.
     English Community       Deutsche Community       Comunidad en Español

  • Portege R700-14J - Compatible with Express Port Replicator II?

    Today I received my TOSHIBA Express Port Replicator II (PA3680E-1PRP) to be used with my TOSHIBA Portege R700-14J (PT311E-023006DU). I seem to be unable to fit the notebook easily into the docking station.
    Please let me knwo whether this port replicator docking station is *the right model* for the Portege R700-14J.
    Thank you
    Bert van Loon

    Hi mostlymedia,
    I have a little bit searched using Google and I found that Port Replicator II is compatible with Portg M750 and Tecra A/M/R/S Series but no information about Portege R700 :(
    In my opinion you should ask the ASP in your country if its the correct part or not before you do something wrong.

Maybe you are looking for

  • Stock transport order requiremnet date does not match in tranRRP3) &MD04

    STO delivery date does not match in transaction MD04 (ECC 6.0) and RRP3 (SCM5.1). This situation occurs when delivery date in STO is past due.  During Shipment Scheduling & avaibilty check, materail staging/availability date(EKET-MBDAT) get updated w

  • Missing fonts in flash menu

    i'm wondering if anyone else has encountered this issue. i've got a collection of fonts in various formats all installed on my pc. several key fonts however, are not included in the flash font menu when i launch flash. they range in format (truetype,

  • In Firefox, bullet graphics not indented; ok in IE

    I am using RoboHelp 6. I have three levels of bulleted lists. In Firefox, all the bullets display flush left. The text is indented correctly. It displays correctly in IE.

  • Mass performance " Tech Closing" pp-orders with mistakes in cogi

    Good afternoon. It would be desirable to realize program mass Those closing pp-orders at which there are mistakes in cogi. Batch input for co02 does not allow to perform such operation, since in it check on a mode of processing (whether Batch input)

  • NW04S WebDispatcher Installation with SAPINST?

    Hi, We have the webdispatcher running under NW04.  The setup was straightforward and worked fine. Now, with NW04S, the WD install manual mentions to use SAPINST.  The SAPINST promts for the SID and we specify the existing real SAP SID that we want th