System User Problems +

My G5 is having issues and I can't seem to get things back up to normal operation. A short while ago, users under my admin became unable to access our printer. I thought it was a printer issue only, but now users cannot burn CD's. As the users are my kids they are most unhappy about this. I have checked all their accounts and they should be able to do these things. I have run disk first aid and it says the machine is fine. I can't verify my permissions because I get a lost contact error when I run disk aid, and I can't seem to get it to reconnect (yes I trashed chess). I have disk warrior 3.0, but my computer won't boot from the disk and of course it can't repair the start up drive, when it being used as start up. I have run fsck but it also says all is fine. Now my machine is taking longer and longer to boot up (it sticks at the grey apple screen with spinning circle-clock thing). I think its sick, but I can't seem to do anything to help. Short of reinstalling my system, does anyone have suggestions.

I am wondering if there could be a problem with the hard drive. I suggest that you start Disk Utility from the Utilities menu and then select your disk, which should be the top item at the left of the Disk Utility window. Then, look at the bottom of the window to see what your S.M.A.R.T. status is. If it does not say "verified", then you may well have a hardware problem.

Similar Messages

Login problem with Oracle 10g Express Edition as system user

I have installed Oracle Database 10g Express Edition, but I can not login inside. I use the following:
user: system
password: ****** the password witch I put during the installation.
As I click Login, the page returns to the same state and wants username and password again. As I write wrong user and pass it yields an error, as I write the right user and pass it returns to the same page again. I used uppercase for system and lower case, but the problem goes on. I read the documentation, but I didn't find a solution.
Eventully I may be miss something. Can anyone help me?

Hi,
Are you try to connect sys user on sql command prompt and alter system user password then try to connect
regards
Taj

Problem with "Application lanucher and run as an system user

Hi
Im trying to distribute
Application Lanucher NT Service was not found to run the application as system user.

Mossbrant,
> Im trying to distribute
>
> Application Lanucher NT Service was not found to run the application as
> system user.
>
I guess this is a duplicate of the one below? I will anser that one.
- Anders Gustafsson (Sysop)
The Aaland Islands (N60 E20)
Novell has a new enhancement request system,
or what is now known as the requirement portal.
If customers would like to give input in the upcoming
releases of Novell products then they should go to
http://www.novell.com/rms

System Copy -- database PRR conains user object belongs to system user dbo

Hi all,
I am having an issue while performing the system copy for the sql server.
Actions taken so far.
1.Detached the database.
2.Installed central instance in the target system .
3.Attached the database using attach as option.
4.Then used STM coll for the conversion.
5.Bought sap in Up condition.
Before detaching the database made export for java addin abap in source system
Then I am trying to import the java add in abap using sapinst(system copy option)..In the half of the way i am getting the below message as ..
DATABASE QAS containus user object belongs to system user dbo.
I have performed the 551915 , 151603 but the still the same message is dispalying.
In log files. inserting
TRACE [iaxxejsexp.cpp:208]
EJS_Installer::writeTraceToLogBook()
- Database XIA contains user objects belonging to system user dbo
TRACE [iaxxbjsmod.cpp:301]
CJSlibModule::showMessageBox_impl()
<html> <head></head> <body> <b>Problems were found after checking configuration of database server b><br>- Database XIA contains user objects belonging to system user dbo<br><br>SOLUTION: Fix these problems to continue the installation. </body> </html>
TRACE [iaxxgenimp.cpp:845]
showDialog()
waiting for an answer from gui
TRACE [iaxxdlghnd.cpp:180]
CDialogHandler::doHandleDoc()
ACTION_OK received
ERROR 2009-01-09 12:52:31 [iaxxinscbk.cpp:289]
abortInstallation
MDB-05919 Errors were found when checking connection to or configuration of database server (listed above in the log file).
TRACE [iaxxejsbas.hpp:270]
EJS_Base::dispatchFunctionCall()
JS Callback has thrown std::ESAPinstException: ESAPinstException: error text undefined
TRACE [syxxcfsmgt.cpp:430]
CSyFileSystemMgtImpl::getFile(iastring,bool)
lib=iamodmssql module=CIaNtMssDmo
WARNING: THE FUNCTIONALITY YOU ARE USING IS DEPRECATED: getFile(const iastring & sFullName, bool bCaseSensitive) const. Use getFile(const PSyFSPath &) const instead.
TRACE [syxxcfsmgt.cpp:195]
CSyFileSystemMgtImpl::getNode(iastring,bool)
lib=iamodmssql module=CIaNtMssDmo
WARNING: THE FUNCTIONALITY YOU ARE USING IS DEPRECATED: getNode(const iastring & sFullName, bool bCaseSensitive) const. Use getNode(const PSyFSPath &) const instead.
TRACE [syxxcfsmgt.cpp:921]
CSyFileSystemMgtImpl::isExisting(iastring,bool)
lib=iamodmssql module=CIaNtMssDmo
WARNING: THE FUNCTIONALITY YOU ARE USING IS DEPRECATED: CSyFileSystemMgtImpl::isExisting(const iastring & , bool , ISyNode::eNodeType ) const. Use CSyFileSystemMgtImpl::isExisting(const CSyPath & , ISyNode::eNodeType ) const instead.
WARNING 2009-01-09 12:52:31 [iaxxccntrl.cpp:477]
CController::stepExecuted()
The step dSetActionUnattended with step key J2EE_EngineEnterprise_Addin_OneHost|ind|ind|ind|WebAS|630|0|J2EE_EngineEnterpriseDialogs|ind|ind|ind|WebAS|630|0|J2EE_Engine|ind|ind|ind|J2EE_Engine|630|0|MssJ2eeDBSetup|ind|ind|ind|ind|ind|0|MssDatabaseInfo|ind|ind|ind|ind|ind|0|dSetActionUnattended was executed with status ERROR.
TRACE [iaxxcsihlp.hpp:301]
main()
An error occurred during the installation of component SAP NetWeaver '04 SR1> SAP System Installation> Java Add-In for ABAP> MS SQL Server> Central / Distributed System> Java System Finalization. Press the log view button to get extended error information or press OK to terminate the installation. Log files are written to SAP NetWeaver '04 SR1> SAP System Installation> Java Add-In for ABAP> MS SQL Server> Central / Distributed System> Java System Finalization.
TRACE [iaxxgenimp.cpp:845]
showDialog()
waiting for an answer from gui
TRACE [iaxxdlghnd.cpp:180]
CDialogHandler::doHandleDoc()
ACTION_OK received
WARNING 2009-01-09 12:52:33 [iaxxcsihlp.hpp:250]
main()
An error occurred during the installation.
Regadrs
Vijay

Hi,
what do you get executing this statement:
use <SID>
go
select * from sys.objects where schema_id =
(select schema_id from sys.schemas where name = 'dbo')
go
Sven

How to use the SYSTEM user in hana cloud

Hello guys, I started with HANA cloud trial, but I havent been able to activate any projects due to an error with permissions,
Repository operation failed
Repository request failed. Cause: Repository: User is not authorized to execute specified operation;User 'DEV_7UKVVFEAC54C2E59OZZQSHXEN' has no authorization, privilege: 'REPO.EDIT_IMPORTED_OBJECTS', package: 'hello'!, code: 40,156, argument:
Now I believe the problem is obvious is that I dont have enough privileges, I went to the Users view and tried to add permissions to my user but I found out other error:
SAP DBTech JDBC: [7]: feature not supported: grantor and grantee are identical
Now I saw in several threads that if we want to add more privileges we should add them using SYSTEM user, but I just dont know how to log in with the SYSTEM user or how to switch to that user.
Any ideas or steps on how to do it?
Greetings!

I just tried performing the exact same steps as described in the tutorial and I can confirm that I get the same error. I get the same error from the Web IDE when trying to activate folders created via the sharing wizard of the Studio.
The problem would seem to be with the Studio version that is currently available from the HANA Tools update site. When packages are created from the project explorer (either directly or through project sharing), they are marked incorrectly as foreign projects (the little blue arrow on the icon).
However if you create the packages via the Content folder of the Systems view (as I did above for the hello package) or via the Web IDE; they are created correctly. I was able to setup a project in the Studio by pre-creating the package in such a way and then creating/sharing the project into the existing package. I still got an error on the .settings sub-folder, but I could ignore it and still activate the other objects.
Therefore I would suggest this approach or using the Web IDE.

File Permissions on Oracle Directories for other Operating System Users

Hi,
I am trying to export the table data to flat file using a pl/sql function using UTL_FILE package and directories created using 'CREATE DIRECTORY' command. The function is called from a stored procedure which in-turn is called from a Java program using JDBC and the Java process runs as different operating system user. The problem for me is the file exported is being written as 'ORACLE' user with 'OINSTALL' group and '-rw-r--r--' linux file permissions. When I try to read this exported file from the java program it throws me a file access error.
I would like to know if we can specify any additional parameters either in
1) Database parameter file
2) UTIL_FILE.FOPEN function
3) CREATE DIRECTORY command
so that the files written to the DIRECTORY have a read write access.

Since you attempting to read the file from Java, you are constrained by the OS.
Write a stored proc to read the file, since PL/SQL does have the correct permissions to read/write to files.
P;

Outputting System User Name in Ad Hoc Query (S_PH0_48000513)

I am trying to create an HR Ad Hoc Query and one of the fields that I am trying to output is System User Name from infotype 0105 Communications. If I choose this field and do not choose the Communication Type, I get two records per employee - one record with the System User Name populated and one record with a blank value for System User Name.
If I choose the System User Name field for output and also make a selection on Communication Type (= subtype 0001), employees with no System User Name (i.e. no Infotype 0105, subtype 0001) are eliminated from the report.
I want the report to show all selected employees, including those without a System User Name; however, I do not want the same employee to appear on the report twice.
Has anyone else experience this problem? If so, have you figured out how to eliminate the extraneous record for each employee when you do not select the Communication Type?
Thanks in advance.

Hi,
Love to know if you managed to find a solution for this issue as I'm experiencing the same problem. However I'm reporting on both system user and email address which are distinct fields and would prefer to see this information only on a single line. With my report I get communication system user on one line and then email address on the another, I'd also like to be able to include those users where the info types have not been maintained.
With the query I have created I also included logon data from the USR02 table.
Cheers
Bill

After sql server 2012 installation, I have changed sql server database engine service account from network service user to system user. What is disadvantages of this process?

     After
sql server 2012 installation, I   attached my production db. Because of some reasons, i
changed sql engine account from network service user to system user by means of sql server configuration manager.
     Now , there isn’t
a problem at sql server running system. But
I have doubts that
this can produce problems later. Because sql server database engine account must have privileges that listed below;
Log on as a service (SeServiceLogonRight)
Replace a process-level token (SeAssignPrimaryTokenPrivilege)
Bypass traverse checking (SeChangeNotifyPrivilege)
Adjust memory quotas for a process
(SeIncreaseQuotaPrivilege)
Permission to start SQL Writer
Permission to read the Event Log service
Permission to read the Remote Procedure Call service
While sql server installation, setup gives these
privileges to network service user automatically, but changing user by means of sql confugarition manager does not give these
privileges.
Now, system user has privileges listed below. And sql server has been running for 1,5 months without any problems.
Log on as a service (SeServiceLogonRight)
     Bypass traverse checking
(SeChangeNotifyPrivilege) (Everyone user has his privileges. So i think that system user has this privilege also)
What problems can occur because of this situation? Shall i give other privileges to system user and restart sql server or not? And how can i give these privileges to system user listed below;
Replace a process-level token (
this can be set from user rights assignments)
Adjust memory quotas for a process
(this can be set from user rights assignments)
Permission to start SQL Writer (
? - give advice )
Permission to read the Event Log service (
? - give advice )
Permission to read the Remote Procedure Call service (
? - give advice )

Our server is windows server 2008 r2 enterprise edition. I have looked the bunch of permissions in user rights menu that is in local security policy settings gui.
And i have seen those permissions below were not granted to system user;
Bypass traverse checking (SeChangeNotifyPrivilege)
Adjust memory quotas for a process
(SeIncreaseQuotaPrivilege)
So, briefly you say, don't panic ?

Not able to connect to orcl database other than system user

Hi,
I am getting the following error when I am trying to connect to orcl database.
I had created a user 'jeff' on oracle and oracle_sid is already set and database is up.listener is started, tnsnames.ora, listenrer.ora are configured.What other problem can be?
The point is that I am able to connect to orcl using "system" user but not "jeff".
If possible can you send me the snippet of commands to create user , granting privilege to orcl. I had refered oracle guide but may be I am doing some silly mistake.
sqlplus /nolog;
SQL>connect /@orcl;
SQL*Plus: Release 10.2.0.1.0 - Production on Mon Feb 12 10:11:24 2007
Copyright (c) 1982, 2005, Oracle. All rights reserved.
ERROR:
ORA-12154: TNS:could not resolve the connect identifier specified
Enter user-name: jeff
Enter password:
ERROR:
ORA-01034: ORACLE not available
ORA-27123: unable to attach to shared memory segment
Linux Error: 13: Permission denied
Thanks,
Sayantani

Are you working on the same machine where you installed the database and created the user ? If yes, then there is no need of giving @tnsname option. You can directly use sqlplus scott/tiger command to login from the prompt.
If from another machine and provided you have configured oracle networking, you can login as follows.
C:\>sqlplus scott/tiger@yourtnsname
SQL*Plus: Release 9.2.0.1.0 - Production on Mon Feb 12 08:10:06 2007
Copyright (c) 1982, 2002, Oracle Corporation. All rights reserved.
Connected to:
Oracle9i Enterprise Edition Release 9.2.0.1.0 - Production
With the Partitioning, OLAP and Oracle Data Mining options
JServer Release 9.2.0.1.0 - Production
SQL>

Can't Start WLi server, Need info on System User Rights

Hi:
System
WIN 2K Professional
Laptop Dell Latitude
No matter what system/Administrator user I try to use I can't start the WLserver
for WLi. Error message is at end of posting
What am I missing? or what rights should be assigned system user for WL to start?
A system user name and password. WebLogic Server user names and passwords can
contain any character from the JDK supported character sets, including international
characters.
Thank You
David L. Wasler
[email protected]
ERROR MEssage
<Feb 10, 2003 1:37:51 PM CST> <Notice> <Management> <140005> <Loading configuration
D:\bea\user_projects\wlidomain\confi
g.xml>
<Feb 10, 2003 1:38:15 PM CST> <Notice> <Security> <090093> <No configuration data
was found on server myserver_wli for r
ealm CompatibilityRealm.>
<Feb 10, 2003 1:38:16 PM CST> <Notice> <Security> <090082> <Security initializing
using realm CompatibilityRealm.>
<Feb 10, 2003 1:38:16 PM CST> <Critical> <WebLogicServer> <000364> <Server failed
during initialization. Exception:java.
lang.SecurityException: Authentication for user administrator denied
java.lang.SecurityException: Authentication for user administrator denied
at weblogic.security.service.SecurityServiceManager.doBootAuthorization(SecurityServiceManager.java:1078)
at weblogic.security.service.SecurityServiceManager.initialize(SecurityServiceManager.java:1216)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:723)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:594)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:282)
at weblogic.Server.main(Server.java:32)

Igore this message please. my machine was not having IPC resources that
is why this problem was comming. I removed some of the IPC keys and it
started to work.
thanks,
Abhishek.
Abhishek Srivastava wrote:
Hello All,
I was successfully using tuxedo on my Red hat linux machine.
Now I changed my linux to Mandrake. Now I cannot start tuxedo
anymore. my ULOG is showing the following error
110622.nt10172!BBL.3682.1024.0: LIBTUX_CAT:756: ERROR: Cannot get status
for server files /apps/Tuxedo/bin/BBL and /apps/tuxedo/bin/BBL
110622.nt10172!BBL.3682.1024.0: LIBTUX_CAT:248: ERROR: System init
function failed, Uunixerr = : stat: No such file or directory
110622.nt10172!tmboot.3681.1024.-2: 06-21-2002: Tuxedo Version 7.1
110622.nt10172!tmboot.3681.1024.-2: CMDTUX_CAT:825: ERROR: Process BBL
at hello failed with /T tperrno (TPEOS - operating system error)
110622.nt10172!tmboot.3681.1024.-2: WARN: No BBL available on site hello.
Will not attempt to boot server processes on that site.
110622.nt10172!BBL.3682.1024.0: CMDTUX_CAT:26: INFO: The BBL is exiting
system
regards,
Abhishek.

Roles for the System user

Hi All,
Currently, I am working on AII 5.1 Slap and Ship Outbound scenario and got the document from the service marketplace under http://service.sap.com/rfid -> SAP AII 2007.
Under Activating HTTP Services(Page no: 9 - 9th step) section , we have to provide the System user. May I know what all roles we have to assign for that user?
Regards
Sara

Hi Sara,
We need to use a System/Communications User in there. Though there is no clear thought on what authorizations are required for the same.
You can ask your basis guys to give a Systems user for restrictive access. This might be based on the policy of the basis team of what auths are generally given for a System user for a restricted use. You can use the same.
If this causes problems you can assign the user, the AIN related admin roles mentioned in the same document. This will work.
I have created a user called ALEREMOTE which is of the type Communications data with profile assigned SAP_ALL. This works for me perfectly.Though if you want you can give in a restricted access to as i have already mentioned.

Second system User cannot see files for first system User

For reasons too complex to go into, I had to set up a second system User. (Okay, an Apple tech at the Apple Genius Bar did this, to fix corrupted Apple Mail)
I am both Users. Both are admins.
According to the documentation, User2 should be able to see files belonging to User1 (and vice versa, I presume), but this is not happening. It looks like I have to manually transfer files from User1 to User2. (Once I do this, I will abandon User1, so I don't have to keep them in sync.)
How to set up so User2 has access to User1's files (and vice versa)?

Once you enable sharing, you use the Finder window to go to the other user home folder/directory. For example, if you're logged in as user1 and you want to see the user2 tree, just tell Finder to open /Users/user2 (via the Go command). This assumes that all your user folders are located in /Users - if you have for example a separate disk for user folders then you would substitute that volume name - for example you have all your user home directories on /Volumes/Users, you would tell the Go command /Volumes/Users/user2
Also, just to make something clear - don't spread your files across the two user accounts - copy all the stuff from both into one of the user accounts and then when you have everything you need, you can get rid of the account that is no longer needed. The only problem you might run into is that you have files owned by an account that is different from where they are physically located. But if you copy things (don't move them - copy them) you should not run into this issue. But if you do run into this issue, it is easily resolved with a couple of Terminal commands usually. Do you know how to copy things with Finder as opposed to move them?
Does that help?

System User access?

Hi Friends,
We are having some access problem to System user ALEREMOTE in BW system.
We know suitable roles for this problem.
But i would like to know if any precautions (or) points need to be considered before giving more access to the System User?
Please give me your comments.
Thanks
Tony

Hi,
I don't think there is any harm in giving more access to System user because it's a background user and no dailog can abuse the authorizations.
Hope this tip helps.
Cheers
Bala Koppuravuri

Install Error (Operating System User Error)

Hello,
I am having a problem installing Oracle 9ias application server. I installed it once and then thought I messed the install up because I couldn't log on to the application manager. Anyway I deinstalled it using the product installer software they supply and then I rebooted and now I continue to get the following error. I am the only user who has ever tried to install the software.
All Oracle 9iAS installations on a host must be installed by the same operating system user. The initial Oracle 9iAS installation located at C:\ora9ias was installed by a different operating system user. Please exit the install, log in as the user who installed the inital Oracle 9iAS installation and restart the install.
Any ideas?

Hi,
you must drop manually the references in regedit to old iAs orcle home. Then you must drop the key 'em_loc' in regedit located in HKEY_LOCAL_MACHINE>Software>ORACLE if this key is pointing to Oracle 9iAS home.
I have done this and I've installed my ias instance right in W2K.

System user passowrd expired - how to reset?

Hello, I've got a problem with 'Expired password' issue for SYSTEM user in APEX. When I try to login using my old password I get a prompt saying the password is expired and I have no idea where I can change it. Could you please give me a piece of advice? I'm pretty sure there already may be a response on the forum, but cannot track it...
Thank you in advance!
A.

Log in with any user account that has DBA-level access and issue *ALTER USER SYSTEM IDENTIFIED BY [newpassword];*
If nothing else (assuming you have access to an OS account with sysdba privs), you can issue SQLPLUS / AS SYSDBA to connect as SYS in order to reset the SYSTEM password.

System User Problems +

Similar Messages

Maybe you are looking for