System will not boot when Aironet 802.11a/b/g adapter installed

I have an HP 8000 Elite sff that will not boot after installing the adapter. I am running XP sp3. As soon as I remove the adapter, it boots fine.???

Which adapter ? Aironet 350 or CB21 ?
Do you have another similar adapter to put in the laptop to try ?
Is the problem new ? did it suddenly happen ?
Nicolas.
===
Please rate answers that you find useful

Similar Messages

Windows 8 and Canvio Desk 3TB: System will not boot when external hdd is connected

http://h30434.www3.hp.com/t5/Desktop-Operating-Systems-e-g/HP-PAVILION-A6109N-amp-windows-8-System-w...
Hi,
just recently upgraded to Win Pro on my HP PAVILION A6109N. I also bought a toshiba canvio desk 3TB. What I notice is that if I reboot my pc with the extermnal HDD connected, my system will not boot.
I have check my BIOS boot settings and the order of the boot.
I have tried disabling USB Legacy Support in the BIOS
I have reformatted the external HDD
but still my desktop will not boot if the external HDD is connected....If I disconnect the external HDD...the system will boot up ....
I am at a loss....*** scratching my head ***

Update: The only solution for me was to format the drive as ext3 and plug it into one of my Asus RT-N66U USB ports, as most routers don’t yet recognize 3TB drives as NTFS. It’s not much help to people who don’t have a router with this capability, and it also slows transfer rates to ~12MB/s.
Given the short length of the cable, your only other options are to have the 3TB Canvio sitting right next to you so you can unplug from a front USB port before each boot, or place it towards the rear of your desk and crawl under the desk to disconnect it from your PC prior to each boot.
It's a pity because Toshiba produce great internal HDD's, but my experience when it comes to external drives is they're simply junk. I wish I had read the reviews before purchasing.

How do I get recover disc for vista when system will not boot???? For Pavilion pc a6157c

Pavilion pc a6157c How do I get recover disc for vista when system will not boot????

Read THIS HP Support Document concerning ordering recovery discs for your HP a6157c. Go to THIS HP webpage to order the "Vista Home Premium 32bit 73NAv3PrA1 + Supp 4 Recovery Kit" for your computer. If you are not looking to order the recovery discs or have some other issue with your computer, please provide detailed information concerning the problem.
Frank
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

The system will not boot

Hello, I am trying to install windovws after the restart can not install Yosemite because can`t please format the hard disk.Please help because just yesterday bought macbooc

FYI...the top partition is too full. You need free space. You will need to remove the bottom partition then make the top partition larger. Make sure you have 10% or more free space. If you use Parallels or VMware you don't have to partition your drive. If you use the vm software you can run Windows wihtout having to reboot into bootcamp each time you want to use it.
See this link for help after you resize your top partition.
https://www.apple.com/support/bootcamp/
I forgot to ask...
If the system will not boot, how are you seeing Disk Utility. Are you booted from the Recovery Drive? If yes, then you will need to erase the internal drive and reinstall Yosemite on the internal. When you erase, make it one partition. You can add a second partition later that's smaller.
Note: you posted in the OS X 7 Lion instead of the Yosemite forum. In the future, asking on the correct forum gets the best answers.
Parallels http://www.parallels.com/
VMware Fusion http://www.vmware.com/products/fusion/

Operating reference system will not boot.

hi! bought the iphone 4s in Italy and it does not work. Operating reference system will not boot. Change of firmware and restore did not help. How can I change it while in Russia. Can I send in the mail store??

Hi NcBunky,
Are you using Win 7 64 bit? Did you update the Texas Instruments (TI) USB 3.0 XHCI Host Controller?
I have an H8 1380t PC. Updated the TI USB 3.0 driver and had the same problem.
When booting the PC with the USB 3.0 external drive connected to the PC the PC would not boot. When booting the PC with only the mouse, keyboard, and a USB 2.0 external drive attached the PC would boot. Once booted you could attach the USB 3.0 drive and it worked fine.
Solution was to roll back (reinstall) the TI USB 3.0 XHCI Host Controller to the original factory installed driver.
System now boots with the external USB 3.0 drive attached.
Jaco
****I am not an HP employee****
Please give a" Kudos" if advice received is relevant or" Accept as Solution" if your problem has been solved.
+++++++++++++++++++++++++++++++++++++++++++++++++++++
H8 1380t CTO, Intel i7 3820
16 GB DDR3
Pegatron Motherboard- IPIWB-PB (Pittsburgh), Radeon HD 7570 1GB. Win 7 Home Premium upgraded to Windows 8.1 Pro.
Envy Phoenix 810-150se, Intel i7 4820k
16 GB DDR3
Pittsburgh2 Mainboard, NVIDIA GTX 645- 2GB GDDR5. Win 8.1 Pro.
HP 560z CTO AMD Phenom II X6 1090T
16 GB DDR3.
Radeon HD 6570
Win 7 Home Premium upgraded to Win 7 Pro.
HP ENVY 17t-j000 CTO Quad Edition Notebook. I7 4702mq
12 GB DDR3
Nvidia Graphics
Win 8 Pro
Errare humanum est.

System will not boot up

MB: KT6 Delta-LSR
CPU: XP2500 Barton
GFX: Asus V9520 Magic/T 128mb
RAM: 1028 pc3200 ddr400 (2x512) Geil Branded
HDD: Maxtor 40GB 2mb Buffer
Put it all together formatted the HDD, installed windows, network was working perfectly. (on ASUS via600 board)
Next day turn it on and nothing, zilch not even a flashing cursor top left of screen, dont even boot to DOS. screen is completely blank.
Tested CPU, GFX, RAM and PSU in another base unit and they work fine, yet put them all together and nothing.
1st I thought it was the mainboard so I sent the ASUS board back and ordered the KT6 Delta nice looking board. But still exactly the same problem.
Lights on case are lit all fans are turning ect yet still the system will not boot up i dont even get a flashing cursor top right of my screen.
There is no light with this mainboard for some reason.
All components work when fitted to another mainboard in a different case.
NB: one thing I have noticed is that there are two power sockets on this board,
1. The usual 20 pin socket (which I am connected to)
2. A 4 pin socket near to the CPU (whilst my PSU has a plug that will fit this sockect also, I am unsure as to connect instead of/as well as or leave unplugged.

Like I have stated before, it is the compatibility issue related towards your chip fsb and your memory fsb. I know that not everyone has money to go buy another stick of memory, I don't. But maybe you could exchange from the place you bought and say that it was a mistake? The cheapest route without getting the fsb chip to match the fsb of the memory stick is to get PC2700 memory. Have you tried going for this yet? I'm sure that your motherboard may not be shot, my board didn't get shot after trying to the two different fsb. You have to understand, motherboards are picky when it comes to running the hardware. If there is a conflict, it won't run right, I could run at a lower fsb and get it to work fine, but it wasn't at it's full potential, and I wasn't going to waste my time trying to find the fsb that would work correctly. So, I just let my friend have the stick back. This is why I'm asking you to try a lower speed stick of memory, because I have experienced this. But so far you haven't even seemed to notice my replies, could you take a quick overview of what I have said? Sorry if I come off as rude, just I am taking the time to write these replies and really am trying to help from my knowledge base. I have experienced this type of problem of what you are talking about personally.
Ok, so maybe I might not know it all, seeing that other people replying here have the same mb spec and chip fsb and memory like your trying to run, they might know more when it comes to that area for sure, just I didn't have luck trying to run a faster stick of memory compared to my chip, even though my board could run it, I couldn't get it to work, at all. I would just get a black screen, I thought I shot my GPU. Then I reset CMOS and the bios would flash, then when it would start pulling from harddrive, boom, black screen again. I had my friend tinker with my volt. to the right volts of the memory stick, still couldn't get nothing. This is why I am a little skeptical about you being able to run it at all in the long run. Hopefully you can find a way, maybe it is your manufacturer of your stick, but my conclusion is, if it isn't going to work with one, or two of same speed, try lowering it. Like I said, I tried it on this setup right now, and I didn't have to replace the chip or mobo, or gpu, so those should be fine.

System will not boot with Seagate 3Tb expansion drive plugged in.

I have a HP Pavilion HPE h8- 1214 Desktop , I recieved a Seagate 3TB expasion drive as a gift but when plugged in, the system will not boot. It turns on but thats it. It never gets to the boot sequence. I have it plugged into the top 3.0 usb slot and have tried all of the other slots as well with no sucess. But if I leave it unplugged the system boots right up. I can then plug it in and it works fine. I have plugged it into my wifes HP All- In- One and it boots fine and works. I have a WD 2TB drive that works fine as well on my system . I have searched Segates support for hours and all they say is to change the boot sequence. Have tried that, no go. What they dont get is no matter what I do if that drive is plugged in it never gets as far as booting and reading the boot sequence. Please help. Thank you!

Hi NcBunky,
Are you using Win 7 64 bit? Did you update the Texas Instruments (TI) USB 3.0 XHCI Host Controller?
I have an H8 1380t PC. Updated the TI USB 3.0 driver and had the same problem.
When booting the PC with the USB 3.0 external drive connected to the PC the PC would not boot. When booting the PC with only the mouse, keyboard, and a USB 2.0 external drive attached the PC would boot. Once booted you could attach the USB 3.0 drive and it worked fine.
Solution was to roll back (reinstall) the TI USB 3.0 XHCI Host Controller to the original factory installed driver.
System now boots with the external USB 3.0 drive attached.
Jaco
****I am not an HP employee****
Please give a" Kudos" if advice received is relevant or" Accept as Solution" if your problem has been solved.
+++++++++++++++++++++++++++++++++++++++++++++++++++++
H8 1380t CTO, Intel i7 3820
16 GB DDR3
Pegatron Motherboard- IPIWB-PB (Pittsburgh), Radeon HD 7570 1GB. Win 7 Home Premium upgraded to Windows 8.1 Pro.
Envy Phoenix 810-150se, Intel i7 4820k
16 GB DDR3
Pittsburgh2 Mainboard, NVIDIA GTX 645- 2GB GDDR5. Win 8.1 Pro.
HP 560z CTO AMD Phenom II X6 1090T
16 GB DDR3.
Radeon HD 6570
Win 7 Home Premium upgraded to Win 7 Pro.
HP ENVY 17t-j000 CTO Quad Edition Notebook. I7 4702mq
12 GB DDR3
Nvidia Graphics
Win 8 Pro
Errare humanum est.

210-4125 will not boot when windows 7 x64 is installed

i have posted this problem a while ago "210-4125 will not boot when windows 7 x64 is installed"
hoping that some one new might have had the same problem
HP.......................................HP MINI PC 210-4125
model ................................210-4125
Bios ...................................F08
ser no................................ [edited Serial Number by Moderator]
product no.........................A8V56EA#ABU
Ram ..................................4.0 GB
system board ID............... 338d
processor .........................Atom(TM) CPU N2800 1.86GHz
Product configuration ID..0797200000204600000300100
acording to INTEL the cpu is X64 bit, but the bios will not let a X64 boot up only a x32 bit ?
and i get a message on black screen "you are trying to load an opperating system not compatable" or some thing like that
it would seem that the bios is the problem and not the CPU ? the 08 bios update only covers x32 bit and not x64
if any one out there is running x64 bit windows 7 on the 210-400 range of netbook can you tel me
1. model no
2.CPU
3.Ram installed
4 bios No
thank you
JB

thank you George
i will bear that in mind next time
i see that you work for HP ? do you have any suggestion's for my problem ?
as i mentioned before the notebook works faultlessly when X64 windows 7 is installed via the OEM disk in the external DVD drive , but if i disconnect the DVD drive it will not boot, but gets stuck in boot loop , then if i connect the drive with any windows installation disc loaded in it , it loads perfect and works perfect even if i disconnect when loaded , but i can not keep the drive connected ?
i have tried to use a USB flash drive to install X64 windows 7 but it comes back that the present CPU is not compatible ??
when it clearly states on Intel web site that it is and it works perfect when loaded ?? even the Windows update manager confirms that it will run all X64 windows OS
i understand the the bios "InsydeH20" is a very difficult bios to work with, and that Insyde have blocked the "hidden menu" via software ? i have exhausted all the software functions to open the complete bios that i can find at the moment , i think it is locked out from out side the bios and not from inside.?
any pointers in the right direction would be very helpful ,
many thanks
John

W520 will not boot when docked; blue screen

W520 fails to boot 100% of the time when docked. Blue screen shows SYSTEM_SERVICE_EXCEPTION, STOP x0000003B for nvlddmkm.sys
nvlddmkm.sys is the NVIDIA driver, which is version 8.17.12.9620, the latest shown on the NVIDIA and Lenovo websites. BIOS is also the latest.
Systems boots fine if I remove it from the dock, but it will not boot when docked.
Windows 7 PRO SP1
2 external monitors via DVI
Any suggestions?

Boot with Option held down. After the cursor changes to an arrow, Command-. (Command Period) should open and close the optical drive. After you insert the disc, click the curved arrow to have it re-scan the discs for boot volumes. Then select the optical drive and click the straight right-pointing arrow to start.
Try it with the Apple Hardware Test disc first and run Extended Tests.

Reset CMOS, system will not boot

This is a long story but I will try to keep it short:
I just bought a new 875P Neo-FISR and a 3.0 GHz Prescott, which from reading the other posts could have been a mistake. I installed the CPU, memory, and the video card and pressed the power button and received a "CMOS Data Wrong" error. So I tried to correct the problem but when I saved and exited then the system would not boot back up. So, I reset the CMOS via the jumper and tried again. After MANY attempts I change just the month in the date setting. And what do you know...it would not boot back up. The D-Bracket LEDs were: 1-flashing red/green, 2-flashing red/green, 3-red, and 4-red
I must have read almost every post in this forum and tried many things such as:
disconnecting all componets except for video, ram, and cpu
the during boot to recover the BIOS
removing mobo from case, maybe a short
moving the memory to different slots
moving the PSU to a different computer...it works
disconnecting the PSU from the mobo and and removing the battery overnight. The first night I did not disconnecting the PSU from the mobo and I found that did nothing.
Tryed everything that I could think of and some stuff that others thought of but nothing worked. However the last item...removing the battery...did change things some. Now nothing happens, and I mean nothing...no lights, no fans, no buzzing...nothing.
Any ideas would be greatly appreciated. The only recourse I have left is to RMA the board.

I tried one stick in all of the slots with and without the sound card. That did not work either.
The voltage for my memory is 2.6 so that is what I tried. But if I can get it to boot up again I will try 2.7.
Tks.

System will not boot - Arrives at 'Bluetooth Setup Assistant popup &

A Bluetooth Setup Assistant (BSA) pop-up arrived on my screen looking for bluetooth mouse (which I do not have). It is in front of the log-in screen (I can just see it behind the BSA pop-up). I cannot get rid of it. The keyboard and mouse will not work and i cannot reach any of the system tools as the system has not booted. I tried (a) shutting off & restarting. But it always arrives at this same screen. (b) safe mode start with same result. (c) Command Option PR start with same result. (d)Then put in installation disk to start from disk (Holding down 'C') with same result. Now my installation disk will not eject (holding down mouse button on startup). (e) Also tried startup with firmware (Command-Option-O-F) with same result.
Can anyone help get me round this original problem as well as finding a way of ejecting the installation disk?

Note: I assume in the following that your mouse & keyboard are standard USB wired devices -- if not, please say so. Also, if yours are not Apple branded devices, please mention that too.
It sounds like your keyboard & mouse are not being recognized as connected to your Mac so the OS is looking for Bluetooth devices as an alternate source of user input. If this is so, what may help is to unplug them & plug the keyboard into a USB port on your Mac (not on a USB hub attached to it) after restarting, when you see the BSA screen.
If this doesn't work, try unplugging all other USB devices & repeat the above. If that doesn't work, you may have a defective keyboard or mouse. Check for that by substitution.

System will not boot or POST

I have a Pavilion A8 Vision that will not boot or complete POST and does not communicate in any way. Fans are on, sounds from drives seems like beginning of POST. I have removed and replaced RAM with other piece - no change. When RAM is out of motherboard system will report 5 long beeps and repeat the beeps for 4 to 5 times. Need help and/or advice on replacement of components.

Hello , Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I have read your post on how your computer is not able to start up properly, and that it is emitting a BIOS beep code. I would be happy to assist you in this matter! According to the information in this resource on BIOS Beep Codes, 5 long beeps indicate that 'fatal errors related to the operation of critical motherboard components - such as teh CPU' have become defective. To correct this issue, I recommend contacting our technical support for further assistance in this matter by clicking the link below to get the support number for your region.
www.hp.com/contacthp/
I hope this helps!
Regards

Tried to update Mac book pro to maverick now system will not boot

I downloaded the maverick update but something happened during the update and now my Mac book pro will not boot into the os. What should I do?

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

HP Pavilion DV7; System will not boot; Memory Test Failed using Advanced System Diagnostics

Not sure exactly how, but I managed to contracted several variants of the nasty Rovnix virus and now my system will not even boot into Safe Mode after trying to restore to several different restore points. Enabled bootlogging, but not sure how to retrieve the log.
Currently am able to get into HP Advanced Diagnostics and began Start-Up Test. Test failed on Memory Module:
Failure ID: Q0AE6C-5LS79T-MFH15G-406N03
Any next steps or directional assistance would be greatly appreciated. Thank you in advance!

Hello @GarrettBishop,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your notebook computer has failed a memory test in the advanced system, and I would be happy to assist you in this matter!
Since the Failure ID has come up with Q0AE6C-5LS79T-MFH15G-406N03, I recommend contacting our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

New system will not boot up.

I am in the process of building a new system and it will not boot to the post. The power gets to the cpu fan and case fan for about 5 seconds then shguts off. I have to clear cmos to get the same response. Please help, I have pulled everything from the case and tried to boot with just the cpu and memory. Same result.

Quote
Originally posted by FastEddie
The Antec Bug involves their True Power line of psu's and involves a problem with the +5vsb. It's caused quite a few problems with many different boards, from stability issues, to boot issues, to freezing in cmos setup issues. Here's a couple links:
Antec Problems with Neo 2 Platinum
Antec RMA
Read these through.
Would be nice if you guys had different psu's to try.
I recently had the "reboot loop during startup" problem with an Abit AI7 and the Antec TruePower 480. However, the problem didn't start to occur until several months after it was new. After replacing the PS with a 430 amp Enermax the problem went away.

System will not boot when Aironet 802.11a/b/g adapter installed

Similar Messages

Maybe you are looking for