System won't boot with incorrect date/time

Hey, I setup a computer back home for VNC, however there was a power outage and now the BIOS has reset. Unfortunately it defaults the date to 2099 for some reason, anyway now the computer won't boot (I can't remember the exact error). Anyway the trouble is I can't access that computer now, and it has no monitor hooked up, is there anyway I can force a boot with just keyboard and without setting the correct date in the BIOS (no one with access to the computer could do this).
Appreciate any help.

You can try to just press F1.
I have a similar issue with my home server, the battery on the motherboard is dead so when the pc is powered off for a while it will not remember the clock. When trying to boot the system in such a case it spits out an error where it offers to "ignore" the error if you press F1.
In my case I need to wait until my pc beeps before pressing F1, basically you need to get past the BIOS stage.
With a bit of luck it might work for you too.
Also I hope you have some ntp service running on your system to make sure the date gets set correctly on your system on bootup.
Last edited by Neburski (2014-02-19 12:35:00)

Similar Messages

System won't boot with PCI-6014 installed

I am using multiple PCI-6014 boards in several systems. One of the systems now fails to boot. By trial and error with parts from other sytems, I have determined that I have a PCI-6014 board which if I place it in any system, the system it is in will not boot. If I remove this particular PCI-6014 board, then the system will boot. These same systems will boot and operate properly with any of my other PCI-6014 boards installed as well.

It appears that there is a problem with the board that prevents the systems from booting up. If you have tried the board in different slots and different machines with the same results, the next step is to request an RMA (Return Merchandise Authorization) for that board by calling our customer service number: 1-866-275-6964.
-Alan A.

System won't boot up

Help please. I have a kt6 delta running an athlon 2700+ xp chip, 512 mb ddr 400.
When I set the fsb at the correct speed for the chip (166) the system won't boot hard drive led lights up constant. dvd drive and cd-r drive each run but the system won't boot. system seems to run fine at default and 133 mhz but the chip is incorrectly identified in windows (xp pro sp1) Any Ideas whats wrong?

Hi - I have the same board with the same processor, I have not problems rebooting after changing the bus speed. But I have had problems rebooting after adding in any card PCI or AGP. the system seems to have trouble clearing the Cmos, I would try clearing the CMOS with the JBAT. it doesn’t always seem to work but I have had some luck, though I have also pulled out the battery a couple of time too..
Good luck!

[865PE NEO2 PFISR] Won't boot with added memory

Recently I upgraded a few items on my PC which has been running fine for 18 months or so. I changed out the video card and bought double the memory of the same brand and type it had in it. I went from 1gig (2 sticks) and added two more sticks. But now it won't boot. The power is on but no output whatsoever.
I RMA'd the memory thinking that might be the problem but it's the same with the new set. I tried all sorts of memory/slot combos. Basically, the new memory works fine if you swap it out in bank A with the old stuff. That's how it's running right now, so I know all of the sticks are good. I can take a third and put it in either slot bank B and it'll boot, but obviously not run properly. But any combination of these four sticks and the system won't boot!
Please help!
I'm running this system:
Win XP (SP1 I believe)
865PE NEO2 PFISR
P4/3.0CGHz, 800M 478P/512K HT
DDR Corsair 512MB X4 (400)
Dual 80gb samsung HDs running SATA
Sapphire X800GTO 256M video card
Antec Sonata case
TruePower 380Watt ATX12V

What brand, model, and speed are the RAM sticks. Did you check your Test Report booklet which came with the mobo. If you can't find it, you can go to the MSI website and look for your MOBO and get the test report that way. Some brands/models will that have been tested are shown in the report to be okay in all 4 slots, some only test okay in 2 or 3. Check this report and if it is one of the brands/model/speed tested you will see how it fared. It may well be you the MOBO doesn't like your RAM in 3 or 4 slots.
Maybe I missed it, but did you try each slot with only one stick at a time? You may also have a bad RAM slot.

Biege G3 won't boot with OS 9.2

I purchased a biege G3 MT with OS 8.6 on eBay. Unfortunately, the OS is in French. I upgraded that to OS 9.2 and now it won't boot. No chime and it stops after the first icon during startup. It won't boot with extensions off nor with the CD. I tried resetting pram, etc. without any luck. Loaded it with 8.5 and it works. Took another HD with 10.2 from another biege G3 and it works. It just doesn't like 9.2, but I have 9.2 running in another biege G3. Are there G3 that won't work with 9.2? Please help.
biege g3 Mac OS 9.2.x

Hi elpro,
Here's a bunch of stock responses you'll hear on the G3 forum.
Is the 9.2 CD a universal installer (gold color), or a gray machine-specific CD, and if it is gray, is it the right one for your machine? Apple made gold CDs for general retail to work with all machines, and gray ones that were usually distributed with a machine with the components just for that machine. Unless you have a universal installer CD, the version of OS 9 you are trying to install may not have the right components for your system unless you happen to have one that matches your type of G3. If the 8.5 CD is the right one, and the OS X you say is from an identical machine then that may explain why they boot up but not your OS 9.
If you post your problem on the G3 forum you'll almost be sure to get this question. How old is the battery in this machine? G3s exhibit all kinds of weird and unexpected symptoms when the batteries are weak, and they go through them pretty quickly, especially if they have been unplugged for a long time. The battery helps preserve basic machine configuration information between bootups so if you're having problems with your monitor it might even be related to the battery. If in doubt, replace the battery.
The PRAM reset and extensions off are the other stock replies but you've tried those.
Brian

PC won't boot with X-fi XtremeMusic

# This is my first post, so please tell me if I'm not giving enough info or anything..
I bought a X-fi XtremeMusic and wanted to try out.. So I plugged it into a free PCI slot to find out it wasn't working: I couldn't boot. The only thing that would happen were the casefans spinning, but my screen remained black.
I then tried to boot without the soundcard in the PCI slot, but my screen was still black.. Then I removed the onboard battery from the mainboard and waited a minute or two and put it back in: I was now able to boot again. I tried this one more time and exactly the same happened.
Now I read something about X-fi soundcards and nForce4 chipsets not meshing very well, but I have a gigabyte MA-790XT-UD4P mainboard, so this doesn't apply to me I assume.
Other specs: AMD Phenom II 720
XFX Radeon HD 4870
CoolerMaster 620w power supply
My question is: what could be causing this problem? Or is it possible that my card is broken?
Thanks!

'Re: PC won't boot with X-fi XtremeMusic? Yeah I tried it in both PCI slots, but none worked. Still I wonder about one thing, which I forgot to mention: When I replace the onboard battery and boot I get an error (which I resolve by using the last known good option instead of putting everything to stock value as I'm overclocking in the bios) that the bios checksum is incorrect, so putting in the card changes some value in the bios.. But what value? And does this imply that maybe updating my bios might solve the problem?
Also might I ask what bios revision you are currently using (I'm using the F4 bios)
About the case thing you might also be right: I do have some difficulty putting in the card as it doesn't fit perfectly. I have a CoolerMaster CM690 case which has tool-free fittings, but I can't get the fitting which holds the card down without using substantial force. This also causes the card to be in the PCI slot at a slight angle, I thought this wouldn't matter as the pins still connect, but may this be a problem? I already tried starting up without the case fitting holding the card in place and instead using my fingertips to hold in postion, though to no avail.
Oh and exactly what bracket should I look at (the one you referred to in your post)?

Btrfs: System won't boot anymore after unclean shutdown

Hi,
I have a problem with my ArchLinux (kernel 3.19.2-1-ARCH).
I have my root partition as BTRFS and no /boot partition.
After an unclean shutdown the system won't boot anymore.
GRUB loads the kernel and the kernel starts but it hangs saying: Mounted /dev/sda3 on real root.
Then, I have to start a Live CD and do:
btrfsck /dev/sda3
After that the system boots correctly.
I've tried adding fsck to the HOOKS in the mkinitcpio.conf file and in fact it tries to fsck the filesystem (but with BTRFS, fsck.btrfs doesn't work...)
What can I do?
Thanks

I'm also having this problem. I tried booting up the netinstall image to debug it, but I can't mount my btrfs volume from there either: mount just hangs. After a while, the kernel goes:
[...] INFO: task mount:612 blocked for more than 120 seconds.
[...] Not tainted 3.19.2-1-ARCH #1
[...] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[...] INFO: task btrfs-transacti:636 blocked for more than 120 seconds.
[...] Not tainted 3.19.2-1-ARCH #1
[...] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
From this post I guessed that I might just need to wait so that I could defrag the volume once it was mounted, but it's been hanging for over 15min now (the message above continues to come up periodically).
Like the OP in the thread I linked to above, my btrfs volume is inside an LVM volume (which is on dm-crypt). Don't know whether that's relevant.
Output of btrfs-check:
Checking filesystem on /dev/pixie/btrfs
UUID: e04cc661-e31a-4dbf-870d-664bc913e34a
found 76855677062 bytes used err is 1
total csum bytes: 72928436
total tree bytes: 2092515328
total fs tree bytes: 1888452608
total extent tree bytes: 104644608
btree space waste bytes: 357251032
file data blocks allocated: 181197139968
referenced 109440282624
btrfs-progs v3.19
dmesg output:
[ 36.824998] Btrfs loaded
[ 36.826713] BTRFS: device fsid e04cc661-e31a-4dbf-870d-664bc913e34a devid 1 transid 98618 /dev/dm-3
[ 46.219014] BTRFS info (device dm-3): disk space caching is enabled
[ 46.259830] BTRFS: detected SSD devices, enabling SSD mode
[ 240.333313] INFO: task mount:539 blocked for more than 120 seconds.
[ 240.335542] Not tainted 3.19.2-1-ARCH #1
[ 240.337795] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.340263] mount D ffff8800cf2837f8 0 539 453 0x00000000
[ 240.340277] ffff8800cf2837f8 ffff8800cf2331b0 0000000000013f00 ffff8800cf283fd8
[ 240.340286] 0000000000013f00 ffffffff81818540 ffff8800cf2331b0 ffff8802094f67a8
[ 240.340291] 0000000000000004 ffff8800cf283758 ffffffffa0a2fc91 ffff8802094f67a8
[ 240.340298] Call Trace:
[ 240.340335] [<ffffffffa0a2fc91>] ? set_extent_buffer_dirty+0x71/0xc0 [btrfs]
[ 240.340357] [<ffffffffa0a05796>] ? btrfs_buffer_uptodate+0x56/0x80 [btrfs]
[ 240.340366] [<ffffffff8155e999>] schedule+0x29/0x70
[ 240.340389] [<ffffffffa0a47745>] btrfs_tree_lock+0x65/0x200 [btrfs]
[ 240.340396] [<ffffffff810b4380>] ? wait_woken+0x90/0x90
[ 240.340410] [<ffffffffa09e5cd9>] btrfs_search_slot+0x799/0xaa0 [btrfs]
[ 240.340425] [<ffffffffa09e79f5>] btrfs_insert_empty_items+0x75/0xd0 [btrfs]
[ 240.340446] [<ffffffffa0a47a37>] btrfs_insert_orphan_item+0x67/0xa0 [btrfs]
[ 240.340465] [<ffffffffa0a4a12e>] insert_orphan_item+0x5e/0x90 [btrfs]
[ 240.340482] [<ffffffffa0a4c531>] replay_one_buffer+0x361/0x380 [btrfs]
[ 240.340504] [<ffffffffa0a2f244>] ? alloc_extent_buffer+0x34/0x370 [btrfs]
[ 240.340523] [<ffffffffa0a488f3>] walk_down_log_tree+0x1d3/0x410 [btrfs]
[ 240.340540] [<ffffffffa0a48bfb>] walk_log_tree+0xcb/0x1d0 [btrfs]
[ 240.340558] [<ffffffffa0a507f7>] btrfs_recover_log_trees+0x1e7/0x490 [btrfs]
[ 240.340575] [<ffffffffa0a4c1d0>] ? replay_one_dir_item+0xf0/0xf0 [btrfs]
[ 240.340596] [<ffffffffa0a08b3e>] open_ctree+0x17ae/0x2030 [btrfs]
[ 240.340609] [<ffffffffa09dd633>] btrfs_mount+0x843/0x920 [btrfs]
[ 240.340618] [<ffffffff8117b7aa>] ? pcpu_alloc+0x35a/0x680
[ 240.340628] [<ffffffff811d5d68>] mount_fs+0x38/0x1c0
[ 240.340634] [<ffffffff8117bb05>] ? __alloc_percpu+0x15/0x20
[ 240.340641] [<ffffffff811f116b>] vfs_kern_mount+0x6b/0x120
[ 240.340647] [<ffffffff811f4184>] do_mount+0x224/0xb40
[ 240.340653] [<ffffffff811f4dae>] SyS_mount+0x7e/0xe0
[ 240.340661] [<ffffffff81562809>] system_call_fastpath+0x12/0x17
[ 240.340671] INFO: task btrfs-transacti:561 blocked for more than 120 seconds.
[ 240.342927] Not tainted 3.19.2-1-ARCH #1
[ 240.345175] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.348473] btrfs-transacti D ffff88020b88bd98 0 561 2 0x00000000
[ 240.348483] ffff88020b88bd98 ffff880211edc590 0000000000013f00 ffff88020b88bfd8
[ 240.348491] 0000000000013f00 ffff8802162289f0 ffff880211edc590 ffff8802094a70c8
[ 240.348496] ffff8802094d8000 ffff880200000000 ffff8802094d8000 ffff880200000033
[ 240.348501] Call Trace:
[ 240.348511] [<ffffffff811b5d1a>] ? kmem_cache_alloc+0x16a/0x180
[ 240.348525] [<ffffffffa09e07ca>] ? btrfs_free_path+0x2a/0x40 [btrfs]
[ 240.348543] [<ffffffffa0a64213>] ? __btrfs_run_delayed_items+0xf3/0x1d0 [btrfs]
[ 240.348550] [<ffffffff8155e999>] schedule+0x29/0x70
[ 240.348568] [<ffffffffa0a0b555>] btrfs_commit_transaction+0x2a5/0xbe0 [btrfs]
[ 240.348573] [<ffffffff810b4380>] ? wait_woken+0x90/0x90
[ 240.348590] [<ffffffffa0a06fc5>] transaction_kthread+0x1d5/0x240 [btrfs]
[ 240.348605] [<ffffffffa0a06df0>] ? btrfs_cleanup_transaction+0x5a0/0x5a0 [btrfs]
[ 240.348611] [<ffffffff81091748>] kthread+0xd8/0xf0
[ 240.348617] [<ffffffff81091670>] ? kthread_create_on_node+0x1c0/0x1c0
[ 240.348624] [<ffffffff81562758>] ret_from_fork+0x58/0x90
[ 240.348629] [<ffffffff81091670>] ? kthread_create_on_node+0x1c0/0x1c0
Last edited by ouroboros8 (2015-04-02 12:37:25)

Won't boot with external display connected

My MacBook Pro (circa 1997) won't boot with the external display connected. I can connect the external display (20in flat planel) after it has started, and it works just fine.
I have tried two different DVI cables (one of which I think is a DVI-A cable) and the DVI-to-VGA cable. The result is the same.
During the boot phase I get the tone, the apple logo and the progress wheel. After 30 seconds to one minute those disappear to be replaced by an empty blue screen.

In case anyone wonders, my "solution" was to change to a WB Elements Desktop 3TB (only USB 2.0 is currently available for this model). I miss the speed of USB 3.0, but it's much nicer to not have to remember to unplug and plug in the hard drive each time I boot.
Still hoping to see a proper solution to this (since I don't have the WB My Book anymore, I can't test adaher's suggestion).

System won't boot-no chime.

Despite repeated attempts and resetting the CUDA button, the system won't boot when start button is pressed. In the first few seconds it seems to make normal sounds; but no chime and settles into simply fan noise. This is true even if using C (with an Install CD). or Shift key. Is there anything else I can try? (I know it's actually a G3 B&W Motherboard; but I had nowhwere else to post it)

I do not remember exactly what was happening when it stopped. It may have been executing something , hung up, and wouldn't respond to the Command-Opt-Esc or I do remember one incident when it was booting up and stopped when it was partly thru "searching for local discs.
I checked the ref. article and tried to measure the voltages on the power connector. I was never quite sure what pin was what, since the colors did not jive with those in the article. At any rate 2 were approx. + 5 V (one was 4.85), the rest were essentially zero (I believe 1 or 2 were about 300 mv). I did notice that when the power connector is reconnected and start up is attempted, 3 little green lights come on on the motherboard. One goes off after a while.
I have tried the old Sonnet upgrade and have tried reseating all the RAM modules. All to no avail.
The Hard drive and all other parts seemed to be working fine prior to the failure.

Upgrade from snow leopard 10.6.8 to montain lion on a iMac system won't boot getting a crossed out circle

Upgrade from snow leopard 10.6.8 to montain lion on a iMac system won't boot getting a crossed out circle

Clean install OS.10.6.8 update it completly. May be you ignored some firmware update.
I have two incedents.
My thunderbolt port stopped working after upgrading to ML 10.8. I booted from external 10.6 , 10.7 still didnt work. Then i clean installed 10.6.8 and ran software update it updated the thunderbolt firmware and all is well now. This firmware update for some reason didnt show up in ML 10.8.
Secondly , when i upgraded my Brother's Macbook from 10.5 to 10.6.3 it would install but stuck with crossed out circle. Then i downgraded checked for update found an efi update , then the 10.6.3 worked fine.

[SOLVED] Switch to systemd - Now system won't boot

I saw that todays update upgrade included the installation of systemd. I looked the wiki and did the necessary changes (I already had made the /etc/hostname etc. files). So I added the
init=/bin/systemd
line to grub and now my system won't boot. I get an error saying something about syslog service not enabled and then a black screen. I can boot my machine fine without the "init=/bin/systemd" line but I want to run a pure systemd system since Arch is moving to it anyway. In the wiki it mentions to install systemd-sysvcompat but it conflicts with initscripts it says. What am I doing wrong or missing?
Last edited by fettouhi (2013-12-08 14:42:04)

fettouhi wrote:
Thanks for the clarification about the DAEMONS list. My DAEMONS list is:
DAEMONS=(!hwclock ntpd syslog-ng !network netfs crond @alsa dbus networkmanager ufw cupsd avahi-daemon samba)
when I try to enable alsa and dbus I get this
[root@andre ~]# systemctl enable alsa-store.service
The unit files have no [Install] section. They are not meant to be enabled using systemctl.
[root@andre ~]# systemctl enable alsa-restore.service
The unit files have no [Install] section. They are not meant to be enabled using systemctl.
[root@andre ~]# systemctl enable dbus.service
The unit files have no [Install] section. They are not meant to be enabled using systemctl.
Is LVM handled automatically by systemd? The reason I ask is because I have the USELVM= set to YES in rc.conf.
I made the permanent transition to systemd and did not start alsa at all - sound works fine - so I never bothered with the alsa-store/alsa-restore service files at all - it just works! Also dbus gets handled by default in systemd so you don't need any starting of dbus service at all... it just works.

E450 won't boot with 4 cpus

E450, 4x300 CPU's all identical, will boot with any one, any two or any three of the five CPU's I have (one extra) but won't boot with any four installed.
When I do I get (transcribed from terminal - no ethernet) is sth like:
CPU0 has assumed the role of boot CPU
Online: CPU0: Ultra-II (V2.0) 3:1 2048kb 2-2 ECache MCap 13
Offline: CPU1:
Online: CPU2: unknown code (code 15) v15.15) ?:? 262080kb ?-? (type 15) ECache MCap 255Incompatable CPU Type -- DISABLED!]
Offline: CP
Hangs right there.
I have latest OP 3.30. Otherwise machine is perfect on three legs!
All points to me to being the top CPU slot maybe? I have a spare board so I'm going to try that.....
In the meantime, any ideas?
Steve

<table border="0" align="center" width="90%" cellpadding="3" cellspacing="1"><tr><td class="SmallText"><b>haroldkarl wrote on Sun, 22 January 2006 12:03</b></td></tr><tr><td class="quote">
the little riser are for is for a sound card... the same one that the Sparc 4 uses... hard to find... the others are "Elite3D-m6 assembly <=540-3058-06 is not compatible with the A20." a horizontal version of the Elite3D-M6... also hard to find.
you do know about this site??? http://sunsolve.sun.com/handbook_pub/Systems/E450/E450.html
haroldkarl
</td></tr></table>
Yes HaroldKarl I know Sunsolve, I work in Sun, but not for Sun!
This is my home E450, I just got it, trying to max it out. I bought four bare ones for 99p, ie about 1.50 Euro....
I used memory from my old Ultra 60, which I thought where 128mb sets, turns out they where 256mb, which the U60 sees as 128mb it seems. Anyway, 3gb RAM now!!
Actually it's quiter than that the U60, a more satisfying low hum of quality iron. I want to take it bed with me!
Steve
PS I have a girlfriend but she's not interested in a threesome with the E450 :(

Macbook pro won't boot with two new 4GB RAM sticks.

I have a mid 2010 Macbook Pro. It came with two 2GB RAM sticks. After downloading Lion, my computer started to get sluggish so I thought I would upgrade the ram. I bought two 4GB Corsair RAM sticks and tried to install them. My computer will boot up if I install one of the new 4GB sticks and leave an old 2GB stick; but it won't boot with both of the new 4GB sticks. Any ideas?

rdsvs wrote:
all specs are the same. old and new has code as below
pc2-5300 ddr2 667 200pin
Unless I misread your reply, that is not quite accurate.
Late 2008 Macbooks uses DDR3 1066MHz 204 PIN.
Late 2011 Macbooks uses DDR3 1333MHz 204 PIN.
Late 2012 Macbooks uses DDR3 1600MHz 204 PIN.

System won't boot. INIT: No inittab file found Enter runlevel:

After the latest update that changed how intel ucode is updated, my system won't boot.
I think I missed a line when I edited "/etc/grub.d/10_linux" and ran grub-mkconfig -o /boot/grub/grub.cfg.
Any ideas on how to fix this?
I can't run grub-mkconfig from another machine, as it uses the live kernel info.
Any help would be greatly appreciated. Otherwise I'll have to reinstall

TheSaint wrote:
SyXbiT wrote:
But I still get the error:
system won't boot. INIT: No inittab file found
Enter runlevel:
It seems to me that you've an old Arch version. inittab is deprecated AFAIK.
What is the Arch iso version?
That would probably be mid-2012 at the very latest I think as that's when I remember completely moving over to systemd...
@SyXbiT: Are you using the current Arch install ISO?

Sawtooth won't boot with anything plugged into it.

My G4 450 won't boot with anything plugged into it at all. The power will go on but no boot. If I unplug everything (except the power cord) it will boot with a chime. Anyone know what the problem could be?

rs6er:
Well, it's likely to be a problem with the video card, the monitor, or the monitor cable. (I assume that this is your normal monitor which was just recently working on your Mac.)
Some thoughts... Have you tried reseating the video card? Does the monitor power on? Do you have another monitor and cable you can swap and try? Will it boot to Safe Mode ("s" key depressed at startup) with the monitor attached?
Gary
Message was edited by: Majordadusma

System won't boot with incorrect date/time

Similar Messages

Maybe you are looking for