Systemd graphical.target leads to black screen

Using a pure systemd setup, I'm trying to boot directly to a display manager.
If I enable the gdm, slim, or lightdm services, the system will drop to a black screen after boot. This does not seem to be an "empty screen," but rather that the system is shutting off my laptop screen.
To regain control of the system, I must reboot and add "systemd.unit=mutli-user.target" to the boot command and drop down to the terminal. From there I can either call "systemctl start display-manager.service" or "systemctl isolate graphical.target" successfully and boot into any of the display managers.
My graphics hardware is an AMD r600 chipset on the FOSS drivers.
I haven't been able to find any messages in any logs (xorg, dmesg, journalctl, etc.) that mention why this is happening.

No ideas whatsoever? I've googled all over the damn place, read through lots and lots of forums that are almost helpful. I'm at a loss here.
What would cause something to not work when it's at the end of the systemd boot process but work fine when run from the command line?

Similar Messages

Linux-lts leads to black screen on rebooting even for linux (solved)

I'd like to mention a problem I faced when trying linux-lts (kernel 3.14). I had the "linux" kernel installed (4.0). If someone has an idea on what happened, please share.
sudo pacman -S linux-lts
, then
grub-mkconfig -o /boot/grub/grub.cfg
, reboot, choose the lts-kernel. I can login to the desktop (lxde, lxqt and i3 are all working). Then reboot, pick any of linux or linux-lts kernels. And here the problem starts: black screen.
I tried to debug the booting process by following https://wiki.freedesktop.org/www/Softwa … Debugging/. I couldn't resolve anything.
By luck I thought "what if it's the login manager (lxdm) that's black?", and so I tried to aim at the middle of the screen with the mouse on the 100% black screen, I entered my password and "boom" I was on the lxqt desktop!
I rebooted, same problem. But by trying to guess where the password box was, I could login to my desktop. To fix the problem at first, I did remove linux-lts, reinstalled linux with pacman, removed lxdm and its systemd service, installed sddm and enabled its service, regenerated the grub.cfg file. Rebooting worked, no black screen.
At that point I thought "well it might just have been lxdm not working well with linux-lts so let's try to install it again, since now I have sddm". Huge mistake... After reinstalling linux-lts, booting in it, rebooting lead again to a black screen on boot up. This time however trying to aim at the box to enter my password was impossible: I was not used to sddm so I didn't know where to click. I tried the "tab" key around 20 times, entering my password each time, without success. So I ended up using the live Arch.iso version on a usb flash drive to remove the linux-lts, sddm (yeah I went for lxdm again), etc. by chrooting. This worked again: no more black screen.
The irony is that I installed that kernel thinking of increasing the stability of Arch on my laptop. It ended up breaking the booting process of both kernels!
And since I want to understand Linux in general, I am posting this in hopes that it could help someone else facing this problem and also in hopes that someone can explain me what could have happened. Because as of now I don't understand how lxdm and sddm could appear black in both kernels when rebooting from the linux-lts kernel.
Thanks for any pointer.
Last edited by linux_dream (2015-05-28 15:57:02)

OK just to confirm that enabling the testing repository solved the problem for me as well.
These were the updated packages (excluding dbus which I manually upgraded before enabling the repo):
Targets (18): device-mapper-2.02.98-3 filesystem-2012.12-1 isl-0.11-1 libpulse-2.99.2-1 libquvi-0.4.1-2 libssh2-1.4.3-1 linux-3.6.9-1
linux-headers-3.6.9-1 lua-5.2.1-2 lua51-5.1.5-3 lvm2-2.02.98-3 mkinitcpio-0.12.0-1 nmap-6.25-2 pulseaudio-2.99.2-1 talloc-2.0.8-1
vlc-2.0.4-5 xorg-server-1.13.0.901-1 xorg-server-common-1.13.0.901-1
It might be any of those but most likely could be either the kernel or xorg-server* (just for future reference).
Cheers, Elisiano

Win 7/Z580: Black screen on boot up, before login screen?

Win 7/Z580: Black screen on boot up, before login screen?
=======================================
I find some interesting posting in this forum. Thanks for keeping this forum to help windows/Lenovo community. I like to pick up the brain of this forum to resolve the black screen issue. I am not sure, whether it caused by virus. I use Microsoft Security Essentials. I am not able to run this in command prompt.
I started my laptop this morning & login screen showed up. Once I entered my login credentials, I heard the sound that usually plays once a login is successful, but I ended up with a black screen. After this occurred, I had to hold down the power button to manually shut down the computer. Once I started it up again, I was prompted to do a system repair, which eventually ended up with all successful outcomes, but I now have a black screen with a cursor before the login screen now. I have no idea what caused this to happen. My laptop is a Lenovo Ideapad Model Z580 (500 GB HD, 6GB RAM).
I am not able to get into safe mode or any other mode, which all leads to a black screen described above. I am able to use the "Repair Your computer" tools after pressing F8 during booting only . All other options leads to Black screen with cursor in the middle
Last Known Good Configuration leads to same
Enable Low Resolution Video (640x480) leads to same My Z580 is not responding to CTRL+ALT+DEL Windows Logo keys as well.
**** I tried SAFE Mode. It loaded couple of drivers and paused at CLASSPNP.SYS load. It went to Black screen with cursor at center.
I am able to invoke control pannel from Command prompt of working PC by typing control.
Z580 PC is not responding to control from command prompt (under Repair Your computer) either.
Z580 is able to use the "Repair Your computer" tools after pressing F8 during booting .
Under local user login it provided Start Repair option. As I pick this option, I got the following. Problem signature
Startup repair offline
1 - 6.1.7600.16385
2 -
6.1.7600.16385
3 - unknown
4 - 21200332
5 - autofailover
6 -
4
7 - NoRootCause
os v - 6.1.7600.2.1.0.2561
locale id – 1033
Under Admin user login, it provided system recovery options. It is not picking up the recovery point created a while ago.
Windows Memory Diagnostics is not launching and shows a black screen without cursor.
I am able to get into command prompt. I tried the following there.
I am not able to run cmd as admin
I reviewed the past posting of this forum on this subject.
Windows 7 boots to an unresponsive black screen with mouse cursor...
System File Checker: Run sfc /scannow & analyze its logs in Windows 7 / 8
Windows Resource Protection could not start the repair service
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program generates in Windows Vista
Force SFC to Run in Windows 7
Windows Resource Protection found corrupt files but was unable to fix some of them
SFC /SCANNOW showed up
"Windows Resource Protection could not start the repair service
I did "net start trustedinstaller"
"Windows Resource Protection detected pending repair restart the computer"
I ran repair options using sfc /scannow /offbootdir=x:\ /offwindir=D:\windows
and got "Windows Resource Protection found corrupt files but was unable to fix some of them "
I did findstr /c:"[SR]" %windir%\logs\cbs\cbs.log >sfcdetails.txt I will be glad to attach the zip file that contain CBS.LOG & [SR] tag extract (xxx.txt).
I did not any find ERRORS there, SFC ended with message saying "found corrupt files but was unable to fix some of them" . It is misleading. There is no [SR] tag pointing to corrupt files. Does SFC through false positive like this?
I ran chkdsk. ResultsFile verification completed.
0 bad file records processed.
0 EA records processed.
CHKDSK is verifying indexes (stage 2 of 5)...
Index verification completed.
0 unindexed files scanned.
0 unindexed files recovered.
Windows has checked the file system and found no problems.
0 KB in bad sectors.
Failed to transfer logged messages to the event log with status 50.
It is puzzling me.
Thanks for helping.

I tried these steps 8/7/2015. I ran chkdsk. Results for D:\
File verification completed.
0 bad file records processed.
0 EA records processed.
CHKDSK is verifying indexes (stage 2 of 5)...
Index verification completed.
0 unindexed files scanned.
0 unindexed files recovered.
Windows has checked the file system and found no problems.
0 KB in bad sectors.
Failed to transfer logged messages to the event log with status 50.
Updated on 8/7
============
Here are my HDD config:
Volume ### Ltr Label Fs Type Status Info
Volume 0 F WDO_Media64 UDF DVD- Healthy
Volume 1 C NTFS Partition Healthy
Volume 2 D Windows7_OS NTFS Partition Healthy
Volume 3 E LENOVO NTFS Partition Healthy
Volume 4 G FAT Removable Healthy
Volume 5 LENOVO_PART NTFS Partition Healthy Hidden
I ran CHKDSK /F /X for C, D, E. All resluted to "Windows has checked the file system and found no problems."
F8 ===> Repair Computer===> Command Prompt ===> Works OK
F8 ===> Repair Computer===> Start up Repair ==> Results into "Startup repair could not detect a problem"
F8 ===> Repair Computer===> System Restore ===> "No restore points has been created on yout computer system drive"
F8 ===> Repair Computer===> System Image Recovery ===> "Windows cannot find a system impage on this computer"
F8 ===> Repair Computer===> windows Memory Diagnostiyics ===> "Black screen with Cursor in the middle"
After getting into Command prompt
I run net user
User accounts for \\
Administrator Guest
The command completed with one or more errors
It did not list other users in my laptop. I do not know why? I tried under F8 ===> Repair Computer===> Command Prompt ===> Works OK
Here is the result:
- Boot with Last Known Good Configuration (F8 menu) ===> Black screen with cursor in the middle
- Restore to a prior date (System Restore) - System Restore ====> Already reported in previous reply
- Try a clean startup Troubleshoot Application Conflicts by Performing a Clean Startup results in
Clean Start up
D:\Windows\System32>runas /user:administrator msconfig
Enter the password for administrator:
Attempting to start msconfig as user "MININT-84TH5FG\administrator" ...
RUNAS ERROR: Unable to run - msconfig
1060: The specified service does not exist as an installed service.
- Try loading defaults in BIOS - F2 ==> f9 ==> f10 ===> Black screen with cursor in the middle
Check if explorer.exe is running and start from CTRL+ALT+DEL (task manager - new task) ===> CTRL+ALT+DEL not responding
Is anybody in this forum point me to fix? Thanks for looking into this issue.

R9 270x Gaming 2G with B84-G43 Gaming Black Screen running win 8.1

Hi,
My system was win 7, upgrade to win 8.1 clean install with AMD Catalyst™ 14.4 for a day then problem occur the same way which many are having "Black Screen" even restart in normal mode but not to Safe Mode.
so i decide to downgrade the system to win 7 clean install, with no display driver install/update "Microsoft Standard VGA Graphic Adapter" in high resolution the system work fine but not with MSI Graphics Driver 13.101, "Black Screen' occur during driver installation detecting VGA card.
which i believe got to be some bios malfunction during the upgrading OS & Driver. by following here i attach the link below as technical details for assistance in advance for this troubleshooting.
here is the picture for the S/N
dropbox.com/s/nglgvrh05thyppf/20140828_091530.jpg?dl=0
and
here is the current vbios version
dropbox.com/s/arrzzrbf46icpoz/Pitcairn.rom?dl=0
*(Sorry, you are not allowed to post external links.)
Thanks.

even i tried it on downgrade and upgrade motherboard bios for both OS by getting a clean/clear default setting.
by using these method, clean OS installation with each of these driver "AMD Catalyst™ 14.4, MSI Graphics Driver 13.101, and the older link by previous post" and on-board vga as main display output;
OS win7 as a result the MSI Graphics driver both version successfully install, process for reboot after the installation of the driver and log into desktop "Black Screen" meanwhile the AMD Catalyst™ 14.4 "Black Screen" during the installation of detecting VGA card.
on the other side of;
OS win8.1 as a result three of these three driver "Screen Freeze" during the installation driver process of detecting VGA card even mouse pointer can't move. picture as link below capture using smartphone;
dropbox.com/s/529wgfjya3rwsik/20140829_155756.jpg?dl=0

MSI N580GTX Lightning Extreme Edition (Black Screen / Reboot)

Hi everyone !
Here's my computer specs :
CPU: Intel I7 870 (2.93 Ghz)
MoBo: Micro ATX from my Dell XPS Studio 8000
Memory: 6Go DDR 667 Mhz
PSU: Corsair HX750(w)
Windows 7 Pro 64 Bits
My problem :
80% of my games (Crysis 1 & 2, Bulletstorm,...) & benchs (3DMark 11, MSI Kombustor, ...) crashes after few seconds. My graphic card goes off, black screen, and then my computer automatically reboot. I've tried another PSU, same pb, and my Corsair HX750 is new. So I wonder if the problem is from my graphics card or my (dell) motherboard ? But my config has the minimum required by MSI.
My temporary solution
After few tests with differents drivers, I've try to change the Core Voltage, no result... So I decided to downclock the GPU freqs.
In order to have something stable to 100%, and be able to run all the games and benchs, i've to downclock the GPU like :
Core Clock : 600 Mhz (Original : 772 Mhz)
Shader Clock : 1200 Mhz (Original : 1544 Mhz)
Memory Clock : 1730 Mhz (Original : 2004 Mhz)
Its a big loss frequency!
Hope a new bios will come out to fix the bug.

Quote
Display driver : ForceWare 280.26
have you tried MSI's drivers for your card?
==> http://www.msi.com/product/vga/N580GTX-Lightning-Xtreme-Edition.html#/?div=Driver&os=All
Remove current driver with >>Driver Sweeper<< in 'Safe Mode' before install the new one
Quote from: Frakatchoo on 07-September-11, 22:13:04
It's only unstable when i'm use the GPU (Games & benchs), not HD videos.
Most games/bench crashes with default clock @ 1.031v. I tried to overvolted & undervolted the GPU, but my tests were not conclusive. The only way i've found to have all games/benchs stable is to downclock the GPU as I explained in my first post.
Maybe i need a more accurate GPU voltage ? Is it important to change Memory & Aux voltage too ?
have you tested with 1050mV for core?
Quote
Is it important to change Memory & Aux voltage too ?
normally not, but depend what exactly is unstable
But it should work fine by default as is

[SOLVED] linux-3.13.6-1 and systemd-210-3 causes black screen

My computer boots into total black screen after recent update, including linux-3.13.6-1, xf86-video-intel-2.99.910-1 and systemd-210-3. I have tried all combinations of rollback, I find linux-3.12.7-2 + systemd-208-2 resolves my problem.
As I dig on, I find it a problem with systemd-backlight. With running kernel-3.13 and systemd-{210,211}, disabling systemd-backlight service either through kernel parameter systemd.restore_state=0 or by masking systemd-backlight service can fix my problem.
Still, I am not the only one experiencing black screen and unresponsive X input with 3.13 kernel: several radeon user seem to have similar phenomenon but cannot be fixed by disabling backlight restore. I would suspect restoring backlight is just one of many ways to trigger this issue, I not experienced in kernel, but I will try to debug the problem. Help will be appreciated.
There seems nothing wrong with X, but a problem with power management.
[ 458.859]
X.Org X Server 1.15.0
Release Date: 2013-12-27
[ 458.859] X Protocol Version 11, Revision 0
[ 458.859] Build Operating System: Linux 3.12.5-1-ARCH x86_64
[ 458.859] Current Operating System: Linux goshawk 3.13.6-1-ARCH #1 SMP PREEMPT Fri Mar 7 22:47:48 CET 2014 x86_64
[ 458.859] Kernel command line: root=/dev/sda6 resume=/dev/sda7 ipv6.disable=1 acpi_osi=Linux i915.modeset=1
[ 458.859] Build Date: 09 January 2014 08:47:24AM
[ 458.859]
[ 458.859] Current version of pixman: 0.32.4
[ 458.859] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 458.859] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 458.860] (==) Log file: "/var/log/Xorg.1.log", Time: Thu Mar 13 15:15:34 2014
[ 458.860] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 458.860] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 458.860] (==) No Layout section. Using the first Screen section.
[ 458.860] (==) No screen section available. Using defaults.
[ 458.860] (**) |-->Screen "Default Screen Section" (0)
[ 458.860] (**) | |-->Monitor "<default monitor>"
[ 458.860] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 458.860] (**) | |-->Device "Intel Graphics"
[ 458.860] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 458.860] (==) Automatically adding devices
[ 458.860] (==) Automatically enabling devices
[ 458.860] (==) Automatically adding GPU devices
[ 458.860] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 458.860] Entry deleted from font path.
[ 458.860] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/
[ 458.860] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 458.860] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 458.860] (II) Loader magic: 0x804c80
[ 458.860] (II) Module ABI versions:
[ 458.860] X.Org ANSI C Emulation: 0.4
[ 458.861] X.Org Video Driver: 15.0
[ 458.861] X.Org XInput driver : 20.0
[ 458.861] X.Org Server Extension : 8.0
[ 458.861] (II) xfree86: Adding drm device (/dev/dri/card1)
[ 459.667] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 459.669] (--) PCI:*(0:0:2:0) 8086:0046:1025:0365 rev 24, Mem @ 0xf0000000/4194304, 0xd0000000/268435456, I/O @ 0x00001800/8
[ 459.669] (--) PCI: (0:2:0:0) 1002:68c1:1025:0365 rev 0, Mem @ 0xb0000000/268435456, 0xafee0000/131072, I/O @ 0x00002000/256, BIOS @ 0x????????/131072
[ 459.670] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 459.670] Initializing built-in extension Generic Event Extension
[ 459.670] Initializing built-in extension SHAPE
[ 459.670] Initializing built-in extension MIT-SHM
[ 459.670] Initializing built-in extension XInputExtension
[ 459.670] Initializing built-in extension XTEST
[ 459.670] Initializing built-in extension BIG-REQUESTS
[ 459.670] Initializing built-in extension SYNC
[ 459.670] Initializing built-in extension XKEYBOARD
[ 459.670] Initializing built-in extension XC-MISC
[ 459.670] Initializing built-in extension SECURITY
[ 459.670] Initializing built-in extension XINERAMA
[ 459.670] Initializing built-in extension XFIXES
[ 459.670] Initializing built-in extension RENDER
[ 459.670] Initializing built-in extension RANDR
[ 459.670] Initializing built-in extension COMPOSITE
[ 459.670] Initializing built-in extension DAMAGE
[ 459.670] Initializing built-in extension MIT-SCREEN-SAVER
[ 459.670] Initializing built-in extension DOUBLE-BUFFER
[ 459.670] Initializing built-in extension RECORD
[ 459.670] Initializing built-in extension DPMS
[ 459.670] Initializing built-in extension Present
[ 459.670] Initializing built-in extension DRI3
[ 459.670] Initializing built-in extension X-Resource
[ 459.670] Initializing built-in extension XVideo
[ 459.670] Initializing built-in extension XVideo-MotionCompensation
[ 459.670] Initializing built-in extension XFree86-VidModeExtension
[ 459.670] Initializing built-in extension XFree86-DGA
[ 459.670] Initializing built-in extension XFree86-DRI
[ 459.670] Initializing built-in extension DRI2
[ 459.670] (II) "glx" will be loaded by default.
[ 459.670] (II) LoadModule: "dri2"
[ 459.670] (II) Module "dri2" already built-in
[ 459.670] (II) LoadModule: "glamoregl"
[ 459.670] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[ 459.673] (II) Module glamoregl: vendor="X.Org Foundation"
[ 459.673] compiled for 1.15.0, module version = 0.6.0
[ 459.673] ABI class: X.Org ANSI C Emulation, version 0.4
[ 459.673] (II) LoadModule: "glx"
[ 459.673] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 459.674] (II) Module glx: vendor="X.Org Foundation"
[ 459.674] compiled for 1.15.0, module version = 1.0.0
[ 459.674] ABI class: X.Org Server Extension, version 8.0
[ 459.674] (==) AIGLX enabled
[ 459.674] Loading extension GLX
[ 459.674] (II) LoadModule: "intel"
[ 459.674] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 459.674] (II) Module intel: vendor="X.Org Foundation"
[ 459.674] compiled for 1.15.0, module version = 2.99.910
[ 459.674] Module class: X.Org Video Driver
[ 459.674] ABI class: X.Org Video Driver, version 15.0
[ 459.674] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
[ 459.675] (II) intel: Driver for Intel(R) HD Graphics: 2000-5000
[ 459.675] (II) intel: Driver for Intel(R) Iris(TM) Graphics: 5100
[ 459.675] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics: 5200
[ 459.675] (++) using VT number 1
[ 459.676] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics
[ 459.676] (--) intel(0): CPU: x86-64, sse2, sse3, ssse3, sse4.1, sse4.2
[ 459.676] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 459.676] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 459.676] (==) intel(0): RGB weight 888
[ 459.676] (==) intel(0): Default visual is TrueColor
[ 459.676] (**) intel(0): Option "AccelMethod" "sna"
[ 459.676] (**) intel(0): Framebuffer tiled
[ 459.676] (**) intel(0): Pixmaps tiled
[ 459.676] (**) intel(0): "Tear free" disabled
[ 459.676] (**) intel(0): Forcing per-crtc-pixmaps? no
[ 459.676] (II) intel(0): Output LVDS1 has no monitor section
[ 459.703] (--) intel(0): found backlight control interface acpi_video1 (type 'firmware')
[ 459.703] (II) intel(0): Output VGA1 has no monitor section
[ 459.703] (II) intel(0): Output VIRTUAL1 has no monitor section
[ 459.703] (--) intel(0): Output LVDS1 using initial mode 1366x768 on pipe 0
[ 459.703] (==) intel(0): DPI set to (96, 96)
[ 459.703] (II) Loading sub module "dri2"
[ 459.703] (II) LoadModule: "dri2"
[ 459.703] (II) Module "dri2" already built-in
[ 459.703] (==) Depth 24 pixmap format is 32 bpp
[ 459.703] (II) intel(0): SNA initialized with Ironlake (gen5) backend
[ 459.704] (==) intel(0): Backing store enabled
[ 459.704] (==) intel(0): Silken mouse enabled
[ 459.704] (II) intel(0): HW Cursor enabled
[ 459.704] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 459.704] (==) intel(0): DPMS enabled
[ 459.704] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[ 459.704] (II) intel(0): [DRI2] Setup complete
[ 459.704] (II) intel(0): [DRI2] DRI driver: i965
[ 459.704] (II) intel(0): [DRI2] VDPAU driver: i965
[ 459.704] (II) intel(0): direct rendering: DRI2 Enabled
[ 459.704] (==) intel(0): hotplug detection: "enabled"
[ 459.704] (--) RandR disabled
[ 459.712] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 459.712] (II) AIGLX: enabled GLX_ARB_create_context
[ 459.712] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 459.712] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 459.712] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 459.712] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 459.712] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[ 459.712] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[ 459.712] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 459.712] (II) AIGLX: Loaded and initialized i965
[ 459.712] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 459.720] (II) intel(0): switch to mode [email protected] on LVDS1 using pipe 0, position (0, 0), rotation normal, reflection none
[ 459.786] (II) intel(0): Setting screen physical size to 361 x 203
[ 459.913] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 459.913] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 459.913] (**) Power Button: Applying InputClass "Acer Keyboard"
[ 459.913] (II) LoadModule: "evdev"
[ 459.913] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 459.913] (II) Module evdev: vendor="X.Org Foundation"
[ 459.913] compiled for 1.15.0, module version = 2.8.2
[ 459.913] Module class: X.Org XInput Driver
[ 459.913] ABI class: X.Org XInput driver, version 20.0
[ 459.913] (II) Using input driver 'evdev' for 'Power Button'
[ 459.913] (**) Power Button: always reports core events
[ 459.913] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 459.913] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 459.913] (--) evdev: Power Button: Found keys
[ 459.913] (II) evdev: Power Button: Configuring as keyboard
[ 459.913] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[ 459.913] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 459.913] (**) Option "xkb_rules" "evdev"
[ 459.913] (**) Option "xkb_model" "acer_laptop"
[ 459.913] (**) Option "xkb_layout" "us"
[ 459.936] (II) config/udev: Adding input device Video Bus (/dev/input/event4)
[ 459.936] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 459.936] (**) Video Bus: Applying InputClass "Acer Keyboard"
[ 459.936] (II) Using input driver 'evdev' for 'Video Bus'
[ 459.936] (**) Video Bus: always reports core events
[ 459.936] (**) evdev: Video Bus: Device: "/dev/input/event4"
[ 459.936] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 459.936] (--) evdev: Video Bus: Found keys
[ 459.936] (II) evdev: Video Bus: Configuring as keyboard
[ 459.936] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input4/event4"
[ 459.936] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 459.936] (**) Option "xkb_rules" "evdev"
[ 459.936] (**) Option "xkb_model" "acer_laptop"
[ 459.936] (**) Option "xkb_layout" "us"
[ 459.936] (II) config/udev: Adding input device Video Bus (/dev/input/event3)
[ 459.936] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 459.936] (**) Video Bus: Applying InputClass "Acer Keyboard"
[ 459.936] (II) Using input driver 'evdev' for 'Video Bus'
[ 459.936] (**) Video Bus: always reports core events
[ 459.936] (**) evdev: Video Bus: Device: "/dev/input/event3"
[ 459.936] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 459.936] (--) evdev: Video Bus: Found keys
[ 459.936] (II) evdev: Video Bus: Configuring as keyboard
[ 459.936] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input3/event3"
[ 459.936] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)
[ 459.936] (**) Option "xkb_rules" "evdev"
[ 459.936] (**) Option "xkb_model" "acer_laptop"
[ 459.936] (**) Option "xkb_layout" "us"
[ 459.937] (II) config/udev: Adding input device Lid Switch (/dev/input/event0)
[ 459.937] (II) No input driver specified, ignoring this device.
[ 459.937] (II) This device may have been added with another device file.
[ 459.937] (II) config/udev: Adding input device Sleep Button (/dev/input/event1)
[ 459.937] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 459.937] (**) Sleep Button: Applying InputClass "Acer Keyboard"
[ 459.937] (II) Using input driver 'evdev' for 'Sleep Button'
[ 459.937] (**) Sleep Button: always reports core events
[ 459.937] (**) evdev: Sleep Button: Device: "/dev/input/event1"
[ 459.937] (--) evdev: Sleep Button: Vendor 0 Product 0x3
[ 459.937] (--) evdev: Sleep Button: Found keys
[ 459.937] (II) evdev: Sleep Button: Configuring as keyboard
[ 459.937] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1/event1"
[ 459.937] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[ 459.937] (**) Option "xkb_rules" "evdev"
[ 459.937] (**) Option "xkb_model" "acer_laptop"
[ 459.937] (**) Option "xkb_layout" "us"
[ 459.937] (II) config/udev: Adding drm device (/dev/dri/card1)
[ 459.938] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=3 (/dev/input/event13)
[ 459.938] (II) No input driver specified, ignoring this device.
[ 459.938] (II) This device may have been added with another device file.
[ 459.938] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 459.938] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event10)
[ 459.938] (II) No input driver specified, ignoring this device.
[ 459.938] (II) This device may have been added with another device file.
[ 459.938] (II) config/udev: Adding input device HDA Intel MID Mic (/dev/input/event12)
[ 459.938] (II) No input driver specified, ignoring this device.
[ 459.938] (II) This device may have been added with another device file.
[ 459.938] (II) config/udev: Adding input device HDA Intel MID Headphone (/dev/input/event11)
[ 459.938] (II) No input driver specified, ignoring this device.
[ 459.938] (II) This device may have been added with another device file.
[ 459.939] (II) config/udev: Adding input device Logitech Unifying Device. Wireless PID:401b (/dev/input/event6)
[ 459.939] (**) Logitech Unifying Device. Wireless PID:401b: Applying InputClass "evdev pointer catchall"
[ 459.939] (II) Using input driver 'evdev' for 'Logitech Unifying Device. Wireless PID:401b'
[ 459.939] (**) Logitech Unifying Device. Wireless PID:401b: always reports core events
[ 459.939] (**) evdev: Logitech Unifying Device. Wireless PID:401b: Device: "/dev/input/event6"
[ 459.939] (--) evdev: Logitech Unifying Device. Wireless PID:401b: Vendor 0x46d Product 0xc52b
[ 459.939] (--) evdev: Logitech Unifying Device. Wireless PID:401b: Found 20 mouse buttons
[ 459.939] (--) evdev: Logitech Unifying Device. Wireless PID:401b: Found scroll wheel(s)
[ 459.939] (--) evdev: Logitech Unifying Device. Wireless PID:401b: Found relative axes
[ 459.939] (--) evdev: Logitech Unifying Device. Wireless PID:401b: Found x and y relative axes
[ 459.939] (II) evdev: Logitech Unifying Device. Wireless PID:401b: Configuring as mouse
[ 459.939] (II) evdev: Logitech Unifying Device. Wireless PID:401b: Adding scrollwheel support
[ 459.939] (**) evdev: Logitech Unifying Device. Wireless PID:401b: YAxisMapping: buttons 4 and 5
[ 459.939] (**) evdev: Logitech Unifying Device. Wireless PID:401b: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 459.939] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.2/0003:046D:C52B.0003/input/input7/event6"
[ 459.939] (II) XINPUT: Adding extended input device "Logitech Unifying Device. Wireless PID:401b" (type: MOUSE, id 10)
[ 459.939] (II) evdev: Logitech Unifying Device. Wireless PID:401b: initialized for relative axes.
[ 459.939] (**) Logitech Unifying Device. Wireless PID:401b: (accel) keeping acceleration scheme 1
[ 459.939] (**) Logitech Unifying Device. Wireless PID:401b: (accel) acceleration profile 0
[ 459.939] (**) Logitech Unifying Device. Wireless PID:401b: (accel) acceleration factor: 2.000
[ 459.939] (**) Logitech Unifying Device. Wireless PID:401b: (accel) acceleration threshold: 4
[ 459.939] (II) config/udev: Adding input device Logitech Unifying Device. Wireless PID:401b (/dev/input/mouse0)
[ 459.939] (II) No input driver specified, ignoring this device.
[ 459.939] (II) This device may have been added with another device file.
[ 459.939] (II) config/udev: Adding input device Logitech Unifying Device. Wireless PID:4101 (/dev/input/event7)
[ 459.939] (**) Logitech Unifying Device. Wireless PID:4101: Applying InputClass "evdev pointer catchall"
[ 459.939] (**) Logitech Unifying Device. Wireless PID:4101: Applying InputClass "evdev keyboard catchall"
[ 459.939] (**) Logitech Unifying Device. Wireless PID:4101: Applying InputClass "Acer Keyboard"
[ 459.939] (II) Using input driver 'evdev' for 'Logitech Unifying Device. Wireless PID:4101'
[ 459.940] (**) Logitech Unifying Device. Wireless PID:4101: always reports core events
[ 459.940] (**) evdev: Logitech Unifying Device. Wireless PID:4101: Device: "/dev/input/event7"
[ 459.940] (--) evdev: Logitech Unifying Device. Wireless PID:4101: Vendor 0x46d Product 0xc52b
[ 459.940] (--) evdev: Logitech Unifying Device. Wireless PID:4101: Found 20 mouse buttons
[ 459.940] (--) evdev: Logitech Unifying Device. Wireless PID:4101: Found scroll wheel(s)
[ 459.940] (--) evdev: Logitech Unifying Device. Wireless PID:4101: Found relative axes
[ 459.940] (--) evdev: Logitech Unifying Device. Wireless PID:4101: Found x and y relative axes
[ 459.940] (--) evdev: Logitech Unifying Device. Wireless PID:4101: Found absolute axes
[ 459.940] (II) evdev: Logitech Unifying Device. Wireless PID:4101: Forcing absolute x/y axes to exist.
[ 459.940] (--) evdev: Logitech Unifying Device. Wireless PID:4101: Found keys
[ 459.940] (II) evdev: Logitech Unifying Device. Wireless PID:4101: Configuring as mouse
[ 459.940] (II) evdev: Logitech Unifying Device. Wireless PID:4101: Configuring as keyboard
[ 459.940] (II) evdev: Logitech Unifying Device. Wireless PID:4101: Adding scrollwheel support
[ 459.940] (**) evdev: Logitech Unifying Device. Wireless PID:4101: YAxisMapping: buttons 4 and 5
[ 459.940] (**) evdev: Logitech Unifying Device. Wireless PID:4101: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 459.940] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.2/0003:046D:C52B.0003/input/input8/event7"
[ 459.940] (II) XINPUT: Adding extended input device "Logitech Unifying Device. Wireless PID:4101" (type: KEYBOARD, id 11)
[ 459.940] (**) Option "xkb_rules" "evdev"
[ 459.940] (**) Option "xkb_model" "acer_laptop"
[ 459.940] (**) Option "xkb_layout" "us"
[ 459.940] (II) evdev: Logitech Unifying Device. Wireless PID:4101: initialized for relative axes.
[ 459.940] (WW) evdev: Logitech Unifying Device. Wireless PID:4101: ignoring absolute axes.
[ 459.940] (**) Logitech Unifying Device. Wireless PID:4101: (accel) keeping acceleration scheme 1
[ 459.940] (**) Logitech Unifying Device. Wireless PID:4101: (accel) acceleration profile 0
[ 459.940] (**) Logitech Unifying Device. Wireless PID:4101: (accel) acceleration factor: 2.000
[ 459.940] (**) Logitech Unifying Device. Wireless PID:4101: (accel) acceleration threshold: 4
[ 459.940] (II) config/udev: Adding input device Logitech Unifying Device. Wireless PID:4101 (/dev/input/mouse1)
[ 459.940] (II) No input driver specified, ignoring this device.
[ 459.940] (II) This device may have been added with another device file.
[ 459.941] (II) config/udev: Adding input device Logitech Unifying Device. Wireless PID:4003 (/dev/input/event8)
[ 459.941] (**) Logitech Unifying Device. Wireless PID:4003: Applying InputClass "evdev keyboard catchall"
[ 459.941] (**) Logitech Unifying Device. Wireless PID:4003: Applying InputClass "Acer Keyboard"
[ 459.941] (II) Using input driver 'evdev' for 'Logitech Unifying Device. Wireless PID:4003'
[ 459.941] (**) Logitech Unifying Device. Wireless PID:4003: always reports core events
[ 459.941] (**) evdev: Logitech Unifying Device. Wireless PID:4003: Device: "/dev/input/event8"
[ 459.941] (--) evdev: Logitech Unifying Device. Wireless PID:4003: Vendor 0x46d Product 0xc52b
[ 459.941] (--) evdev: Logitech Unifying Device. Wireless PID:4003: Found 1 mouse buttons
[ 459.941] (--) evdev: Logitech Unifying Device. Wireless PID:4003: Found scroll wheel(s)
[ 459.941] (--) evdev: Logitech Unifying Device. Wireless PID:4003: Found relative axes
[ 459.941] (II) evdev: Logitech Unifying Device. Wireless PID:4003: Forcing relative x/y axes to exist.
[ 459.941] (--) evdev: Logitech Unifying Device. Wireless PID:4003: Found absolute axes
[ 459.941] (II) evdev: Logitech Unifying Device. Wireless PID:4003: Forcing absolute x/y axes to exist.
[ 459.941] (--) evdev: Logitech Unifying Device. Wireless PID:4003: Found keys
[ 459.941] (II) evdev: Logitech Unifying Device. Wireless PID:4003: Configuring as mouse
[ 459.941] (II) evdev: Logitech Unifying Device. Wireless PID:4003: Configuring as keyboard
[ 459.941] (II) evdev: Logitech Unifying Device. Wireless PID:4003: Adding scrollwheel support
[ 459.941] (**) evdev: Logitech Unifying Device. Wireless PID:4003: YAxisMapping: buttons 4 and 5
[ 459.941] (**) evdev: Logitech Unifying Device. Wireless PID:4003: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 459.941] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.2/0003:046D:C52B.0003/input/input9/event8"
[ 459.941] (II) XINPUT: Adding extended input device "Logitech Unifying Device. Wireless PID:4003" (type: KEYBOARD, id 12)
[ 459.941] (**) Option "xkb_rules" "evdev"
[ 459.941] (**) Option "xkb_model" "acer_laptop"
[ 459.941] (**) Option "xkb_layout" "us"
[ 459.941] (II) evdev: Logitech Unifying Device. Wireless PID:4003: initialized for relative axes.
[ 459.941] (WW) evdev: Logitech Unifying Device. Wireless PID:4003: ignoring absolute axes.
[ 459.941] (**) Logitech Unifying Device. Wireless PID:4003: (accel) keeping acceleration scheme 1
[ 459.941] (**) Logitech Unifying Device. Wireless PID:4003: (accel) acceleration profile 0
[ 459.941] (**) Logitech Unifying Device. Wireless PID:4003: (accel) acceleration factor: 2.000
[ 459.941] (**) Logitech Unifying Device. Wireless PID:4003: (accel) acceleration threshold: 4
[ 459.941] (II) config/udev: Adding input device 1.3M WebCam (/dev/input/event15)
[ 459.941] (**) 1.3M WebCam: Applying InputClass "evdev keyboard catchall"
[ 459.941] (**) 1.3M WebCam: Applying InputClass "Acer Keyboard"
[ 459.941] (II) Using input driver 'evdev' for '1.3M WebCam'
[ 459.941] (**) 1.3M WebCam: always reports core events
[ 459.941] (**) evdev: 1.3M WebCam: Device: "/dev/input/event15"
[ 459.941] (--) evdev: 1.3M WebCam: Vendor 0x4f2 Product 0xb1d8
[ 459.941] (--) evdev: 1.3M WebCam: Found keys
[ 459.941] (II) evdev: 1.3M WebCam: Configuring as keyboard
[ 459.941] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.0/input/input16/event15"
[ 459.941] (II) XINPUT: Adding extended input device "1.3M WebCam" (type: KEYBOARD, id 13)
[ 459.941] (**) Option "xkb_rules" "evdev"
[ 459.941] (**) Option "xkb_model" "acer_laptop"
[ 459.941] (**) Option "xkb_layout" "us"
[ 459.942] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event5)
[ 459.942] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 459.942] (**) AT Translated Set 2 keyboard: Applying InputClass "Acer Keyboard"
[ 459.942] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 459.942] (**) AT Translated Set 2 keyboard: always reports core events
[ 459.942] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event5"
[ 459.942] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 459.942] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 459.942] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 459.942] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input5/event5"
[ 459.942] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 14)
[ 459.942] (**) Option "xkb_rules" "evdev"
[ 459.942] (**) Option "xkb_model" "acer_laptop"
[ 459.942] (**) Option "xkb_layout" "us"
[ 459.942] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event14)
[ 459.942] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[ 459.942] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 459.942] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "Default clickpad buttons"
[ 459.942] (II) LoadModule: "synaptics"
[ 459.943] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 459.943] (II) Module synaptics: vendor="X.Org Foundation"
[ 459.943] compiled for 1.15.0, module version = 1.7.4
[ 459.943] Module class: X.Org XInput Driver
[ 459.943] ABI class: X.Org XInput driver, version 20.0
[ 459.943] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[ 459.943] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 459.943] (**) Option "Device" "/dev/input/event14"
[ 460.036] (II) synaptics: SynPS/2 Synaptics TouchPad: ignoring touch events for semi-multitouch device
[ 460.036] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5822 (res 79)
[ 460.036] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4766 (res 141)
[ 460.036] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[ 460.036] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 15
[ 460.036] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left right double triple
[ 460.036] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7
[ 460.037] (**) Option "TapButton1" "1"
[ 460.037] (**) Option "TapButton2" "2"
[ 460.037] (**) Option "TapButton3" "3"
[ 460.037] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 460.037] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 460.090] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input11/event14"
[ 460.090] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 15)
[ 460.090] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[ 460.090] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MaxSpeed is now 1.75
[ 460.090] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) AccelFactor is now 0.036
[ 460.090] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 460.090] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[ 460.090] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 460.090] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 460.090] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 460.090] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse2)
[ 460.090] (**) SynPS/2 Synaptics TouchPad: Ignoring device from InputClass "touchpad ignore duplicates"
[ 460.090] (II) config/udev: Adding input device PC Speaker (/dev/input/event9)
[ 460.090] (II) No input driver specified, ignoring this device.
[ 460.090] (II) This device may have been added with another device file.
[ 464.074] (II) intel(0): EDID vendor "AUO", prod id 12844
[ 464.074] (II) intel(0): Printing DDC gathered Modelines:
[ 464.074] (II) intel(0): Modeline "1366x768"x0.0 69.50 1366 1414 1446 1466 768 771 777 790 -hsync -vsync (47.4 kHz eP)
[ 1616.997] (II) intel(0): switch to mode [email protected] on LVDS1 using pipe 0, position (0, 0), rotation normal, reflection none
[ 1617.370] (II) intel(0): switch to mode [email protected] on LVDS1 using pipe 0, position (0, 0), rotation normal, reflection none
There is no manual setting file for graphics of X, and here is my lspci result:
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18)
00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 18)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05)
00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05)
00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05)
00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5)
00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05)
00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05)
02:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Madison [Mobility Radeon HD 5650/5750 / 6530M/6550M] (rev ff)
02:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Redwood HDMI Audio [Radeon HD 5000 Series] (rev ff)
03:00.0 Ethernet controller: Qualcomm Atheros AR8151 v1.0 Gigabit Ethernet (rev c0)
05:00.0 Network controller: Intel Corporation Centrino Advanced-N 6235 (rev 24)
ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05)
ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05)
ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05)
ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05)
ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05)
ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05)
Last edited by yuanjie.huang (2014-04-02 11:56:21)

Hello! I seem to be having a similar problem to what is being discussed here. So I figured I would add what is going on with me.
I will try to keep it short but I apologize in advance for it being a bit long.
Hardware: 2006 Imac with Radeon mobility x1600
For me there was no problem before the systemd upgrade to 210 and the upgrade to 211 did not fix the problem of black screen on boot.
Also I upgraded my kernel from 3.13.5-1 to 3.13.6-1 after the problem with systemd started.
Downgrading systemd to 208.10 ( the kernel had been upgraded already) got the system working properly again.
I have since gone back to 211 and have found that:
If I wait for 5 - 10 minutes after the computer boots when I move the mouse the screen wakes up and I can unlock the screen and the computer works as normal.
Note: I am using gdm and gnome3. I think from this that my problem is a brightness/screen not being turned on issue?
If I add nomodeset to the kernel boot parameters the computer works but the Radeon drivers are not loaded.
and after booting with nomodeset if I use "sudo modprobe radeon modeset=1" my computer screen blacks and I have no response.
With both 210 and 211 I can press ctrl+alt+F2 type my username and password into the blind and give commands like "sudo reboot followed by the password" blindly to the computer and the computer will execute them.
I hope that this can be fixed soon... It is annoying at best.
EDIT
I tried "sudo modprobe radeon modeset=1" again and found that I can press ctrl+alt+F2 and get a terminal login prompt that I can use and see! Although gdm login/gnome is still a black screen...
Last edited by BirdOfPray (2014-03-26 21:42:04)

[Xorg] Black screen with 2nd graphic card

Hi !
I'm a french (Sorry for my English) and new on ArchLinux.
I have a problem with my laptop, he have 2 graphics cards, the first one is an ATI Mobility Radeon HD4200 series and the second it's an ATI Radeon HD 5650.
The problem is when I want to use the second card, I have a black screen when I start X. It's the same problem with ATI driver and xf86-video-ati driver even if my card is detected with "lspci" and by "aticonfig --list-adapters" with catalyst driver.
If you need, this is my Xorg log :
Xorg.log with catalyst
Xorg.log with free driver
And if you want my xorg.conf , very basic.
Thanks for your help.

https://bbs.archlinux.org/viewtopic.php … 6#p1133766 FGLRX Configuration
I use one card and found I needed catalyst-dkms pkg as well as catalyst & catalyst-utils
Hope this helps.
Last edited by ackt1c (2012-11-27 15:37:05)

Black screen on startup - Radeon graphics driver or EDID issue?

Having installed Arch, I am only able to boot into Linux (console mode) when I pass the option "nomodeset" in GRUB to disable KMS. If I try to boot with KMS enabled then the screen goes black almost immediately upon boot. There appears to be no further activity from the system: I can't even reboot using CTRL-ALT-DEL. Nor is there any log activity that I can find. The system appears to just hang.
My graphics card is a Radeon 9200. From a general websearch, other people have reported a similar issue with this card on other distros, but the "solution" they get is usually "it now works with the updated version of $(DISTRO)". My next move should probably be to try the Catalyst driver, but there's one other thing that suggests to me that the problem is more to do with the monitor (specifically, with the EDID provision) than the driver....
Running "vbeinfo" at the GRUB command line shows the default resolution as 1280x1024x32. When I run "vbetest" at the GRUB command line, I initially get the graphics test pattern displayed correctly. However, when I press enter to end that test pattern I don't return to the GRUB command line. Instead I get a black screen with a blinking white cursor. No input from the keyboard is displayed if I type, but pressing CTRL-ALT-DEL to reboot does work from here.
I've looked at the section on the Wiki about Forcing Modes and EDID, but this area's still very much a mystery to me, and the Wiki itself says that this secition is still "a WIP". I guess I'm just wondering if, from the behaviour above, if the problem with using KMS is due to an issue with the graphics card itself or if I should be trying to generate my own custom EDID file, which sounds painful . Passing the built-in resolution 1280x1024 via the drm_kms_helper.edid_firmware option, as suggested on the Wiki, made no difference in behaviour at all. Trying to pass 1024x768 in the same way did make snowy artefacts appear on the monitor, but didn't get me to a point where the system appeared any closer to actually booting up.
Any advice would be appreciated. I've currently got the X running fine using the VESA driver (no custom Xorg.conf file needed), but it's more than a little slow. I'd like to have 2D acceleration available at the very least.

logix wrote:
If its a laptop, your screen brightness might be getting set to 0 on boot. If so, try attaching an external monitor to test the theory and set the brightness from a terminal.
export DISPLAY=:0
xbacklight -set 100
Unfortunately it's a desktop with a flat-screen monitor; VGA cable connection. The only information on model that I have is from the monitors' configuration menu: "Dell E248WFP".
More detail on the graphics card: "lspci|grep VGA" gives "01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV280 [Radeon 9200 PRO] (rev 01)"

Black screen after login while on battery with graphics switching enabled

Getting a black screen after entering my password while logging into my account while on battery with graphics switching enabled. Everything is up and running, I just can't see it.
I can log into the guest account on battery
I can log into my account while plugged into power
I can log into my account on battery if graphics switching is disabled
I believe something that is starting up in my account is causing the system to switch from integrated to discrete graphics on login, and that switch isn't working correctly on battery power.
As a work around for now, I can run with graphics switching disabled, but I'd like to solve this so I get longer battery life.
MacBook Pro Retina 15"
Mountain Lion
All updates applied

I had the same issue and managed to reslove it.
Shut down your machine.
Power it back on while holding the 'shift' key (left or right, doesn't matter)
You will see a greay progress bar go across the screen while you boot in to 'safe boot'
Once booted, login, and go to Energy Saver and turn on 'Automatic Graphics Switching'.
Reboot back in to normal mode, and you should be able to log back in and see again.
I did this without being plugged into AC power.
Hope it helps!
Cheers!

Intel hd graphics, black screen on tty switch and more

Hi,
This is my first post on the arch forums, after having used this wonderful distro for half a year. I look forward to being a more active user in the future.
Last week, my laptop HD crashed and i had to re-install arch on a new one. With this came the 3.14 kernel, which I had been holding back at 13.12 previously.
At first I expected something was off with the KMS, but now I am not sure anymore. I can start the system just fine, problems arise when I try to start X, then the screen goes black. Same problem arises if i issue lspci (odd huh?). If I use vgaswitcheroo to switch to the discrete readon, and then back again I can start X and issue lspci just fine. When X is started, I cannot turn it off again (black screen), or change into a vc (same black screen).
I realize this is little to go on, but I would greatly appreciate pointers to what the problem could be and where to look for useful log/debugging information.
Graphics hardware:
Intel hd 3000
Mobility Radeon hd 5470
EDIT:
Here is the Xorg.0.log file from a failing session:
[ 223.612]
X.Org X Server 1.15.1
Release Date: 2014-04-13
[ 223.612] X Protocol Version 11, Revision 0
[ 223.612] Build Operating System: Linux 3.14.0-4-ARCH x86_64
[ 223.612] Current Operating System: Linux lillkalle 3.14.6-1-ARCH #1 SMP PREEMPT Sun Jun 8 10:08:38 CEST 2014 x86_64
[ 223.612] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=c14b180c-886c-4b56-8cbb-0fe1ea9571e5 rw acpi_backlight=vendor acpi_osi=Linux radeon.audio=1 quiet
[ 223.612] Build Date: 14 April 2014 08:39:09AM
[ 223.612]
[ 223.612] Current version of pixman: 0.32.4
[ 223.612] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 223.612] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 223.612] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Jun 12 13:07:40 2014
[ 223.663] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 223.663] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 223.697] (==) No Layout section. Using the first Screen section.
[ 223.697] (==) No screen section available. Using defaults.
[ 223.697] (**) |-->Screen "Default Screen Section" (0)
[ 223.697] (**) | |-->Monitor "<default monitor>"
[ 223.698] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 223.698] (==) Automatically adding devices
[ 223.698] (==) Automatically enabling devices
[ 223.698] (==) Automatically adding GPU devices
[ 223.747] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 223.747] Entry deleted from font path.
[ 223.761] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 223.761] Entry deleted from font path.
[ 223.761] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 223.762] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 223.762] Entry deleted from font path.
[ 223.762] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 223.762] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 223.762] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 223.762] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 223.762] (II) Loader magic: 0x804c80
[ 223.762] (II) Module ABI versions:
[ 223.762] X.Org ANSI C Emulation: 0.4
[ 223.762] X.Org Video Driver: 15.0
[ 223.762] X.Org XInput driver : 20.0
[ 223.762] X.Org Server Extension : 8.0
[ 223.762] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 223.763] (II) xfree86: Adding drm device (/dev/dri/card1)
[ 223.777] (--) PCI:*(0:0:2:0) 8086:0046:1025:0365 rev 18, Mem @ 0xf0000000/4194304, 0xd0000000/268435456, I/O @ 0x00001800/8
[ 223.777] (--) PCI: (0:2:0:0) 1002:68e0:1025:0365 rev 0, Mem @ 0xb0000000/268435456, 0xafee0000/131072, I/O @ 0x00002000/256, BIOS @ 0x????????/131072
[ 223.777] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 223.777] Initializing built-in extension Generic Event Extension
[ 223.778] Initializing built-in extension SHAPE
[ 223.778] Initializing built-in extension MIT-SHM
[ 223.778] Initializing built-in extension XInputExtension
[ 223.778] Initializing built-in extension XTEST
[ 223.778] Initializing built-in extension BIG-REQUESTS
[ 223.778] Initializing built-in extension SYNC
[ 223.778] Initializing built-in extension XKEYBOARD
[ 223.778] Initializing built-in extension XC-MISC
[ 223.778] Initializing built-in extension SECURITY
[ 223.778] Initializing built-in extension XINERAMA
[ 223.778] Initializing built-in extension XFIXES
[ 223.778] Initializing built-in extension RENDER
[ 223.778] Initializing built-in extension RANDR
[ 223.778] Initializing built-in extension COMPOSITE
[ 223.778] Initializing built-in extension DAMAGE
[ 223.778] Initializing built-in extension MIT-SCREEN-SAVER
[ 223.778] Initializing built-in extension DOUBLE-BUFFER
[ 223.778] Initializing built-in extension RECORD
[ 223.778] Initializing built-in extension DPMS
[ 223.778] Initializing built-in extension Present
[ 223.778] Initializing built-in extension DRI3
[ 223.778] Initializing built-in extension X-Resource
[ 223.778] Initializing built-in extension XVideo
[ 223.778] Initializing built-in extension XVideo-MotionCompensation
[ 223.778] Initializing built-in extension XFree86-VidModeExtension
[ 223.778] Initializing built-in extension XFree86-DGA
[ 223.778] Initializing built-in extension XFree86-DRI
[ 223.778] Initializing built-in extension DRI2
[ 223.778] (II) "glx" will be loaded by default.
[ 223.778] (II) LoadModule: "dri2"
[ 223.778] (II) Module "dri2" already built-in
[ 223.778] (II) LoadModule: "glamoregl"
[ 223.779] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[ 223.891] (II) Module glamoregl: vendor="X.Org Foundation"
[ 223.891] compiled for 1.15.0, module version = 0.6.0
[ 223.891] ABI class: X.Org ANSI C Emulation, version 0.4
[ 223.891] (II) LoadModule: "glx"
[ 223.891] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 223.906] (II) Module glx: vendor="X.Org Foundation"
[ 223.906] compiled for 1.15.1, module version = 1.0.0
[ 223.906] ABI class: X.Org Server Extension, version 8.0
[ 223.906] (==) AIGLX enabled
[ 223.906] Loading extension GLX
[ 223.906] (==) Matched intel as autoconfigured driver 0
[ 223.906] (==) Matched ati as autoconfigured driver 1
[ 223.906] (==) Matched intel as autoconfigured driver 2
[ 223.906] (==) Matched modesetting as autoconfigured driver 3
[ 223.906] (==) Matched fbdev as autoconfigured driver 4
[ 223.906] (==) Matched vesa as autoconfigured driver 5
[ 223.906] (==) Assigned the driver to the xf86ConfigLayout
[ 223.906] (II) LoadModule: "intel"
[ 223.916] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 223.954] (II) Module intel: vendor="X.Org Foundation"
[ 223.954] compiled for 1.15.0, module version = 2.99.911
[ 223.954] Module class: X.Org Video Driver
[ 223.954] ABI class: X.Org Video Driver, version 15.0
[ 223.954] (II) LoadModule: "ati"
[ 223.954] (II) Loading /usr/lib/xorg/modules/drivers/ati_drv.so
[ 223.955] (II) Module ati: vendor="X.Org Foundation"
[ 223.955] compiled for 1.15.0, module version = 7.3.0
[ 223.955] Module class: X.Org Video Driver
[ 223.955] ABI class: X.Org Video Driver, version 15.0
[ 223.955] (II) LoadModule: "radeon"
[ 223.955] (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
[ 223.972] (II) Module radeon: vendor="X.Org Foundation"
[ 223.972] compiled for 1.15.0, module version = 7.3.0
[ 223.972] Module class: X.Org Video Driver
[ 223.972] ABI class: X.Org Video Driver, version 15.0
[ 223.972] (II) LoadModule: "modesetting"
[ 224.011] (WW) Warning, couldn't open module modesetting
[ 224.011] (II) UnloadModule: "modesetting"
[ 224.011] (II) Unloading modesetting
[ 224.011] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 224.011] (II) LoadModule: "fbdev"
[ 224.012] (WW) Warning, couldn't open module fbdev
[ 224.012] (II) UnloadModule: "fbdev"
[ 224.012] (II) Unloading fbdev
[ 224.012] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 224.012] (II) LoadModule: "vesa"
[ 224.012] (WW) Warning, couldn't open module vesa
[ 224.012] (II) UnloadModule: "vesa"
[ 224.012] (II) Unloading vesa
[ 224.012] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 224.012] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
[ 224.013] (II) intel: Driver for Intel(R) HD Graphics: 2000-5000
[ 224.013] (II) intel: Driver for Intel(R) Iris(TM) Graphics: 5100
[ 224.013] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics: 5200
[ 224.013] (II) RADEON: Driver for ATI Radeon chipsets:
ATI Radeon Mobility X600 (M24) 3150 (PCIE), ATI FireMV 2400 (PCI),
ATI Radeon Mobility X300 (M24) 3152 (PCIE),
ATI FireGL M24 GL 3154 (PCIE), ATI FireMV 2400 3155 (PCI),
ATI Radeon X600 (RV380) 3E50 (PCIE),
ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
ATI FireGL X2 AK (AGP), ATI Radeon 9600 AP (AGP),
ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP), ATI Radeon 9650,
ATI FireGL RV360 AV (AGP), ATI Radeon 7000 IGP (A4+) 4237,
ATI Radeon 8500 AIW BB (AGP), ATI Radeon IGP320M (U1) 4336,
ATI Radeon IGP330M/340M/350M (U2) 4337,
ATI Radeon Mobility 7000 IGP 4437, ATI Radeon 9000/PRO If (AGP/PCI),
ATI Radeon 9000 Ig (AGP/PCI), ATI Radeon X800 (R420) JH (AGP),
ATI Radeon X800PRO (R420) JI (AGP),
ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
ATI Radeon Mobility 9800 (M18) JN (AGP),
ATI Radeon X800 SE (R420) (AGP), ATI Radeon X800XT (R420) JP (AGP),
ATI Radeon X800 VE (R420) JT (AGP), ATI Radeon X850 (R480) (AGP),
ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP),
ATI Radeon Mobility M7 LW (AGP),
ATI Mobility FireGL 7800 M7 LX (AGP),
ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
ATI FireGL Mobility 9000 (M9) Ld (AGP),
ATI Radeon Mobility 9000 (M9) Lf (AGP),
ATI Radeon Mobility 9000 (M9) Lg (AGP), ATI FireMV 2400 PCI,
ATI Radeon 9700 Pro ND (AGP), ATI Radeon 9700/9500Pro NE (AGP),
ATI Radeon 9600TX NF (AGP), ATI FireGL X1 NG (AGP),
ATI Radeon 9800PRO NH (AGP), ATI Radeon 9800 NI (AGP),
ATI FireGL X2 NK (AGP), ATI Radeon 9800XT NJ (AGP),
ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
ATI Radeon Mobility 9600 (M10) NQ (AGP),
ATI Radeon Mobility 9600 (M11) NR (AGP),
ATI Radeon Mobility 9600 (M10) NS (AGP),
ATI FireGL Mobility T2 (M10) NT (AGP),
ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon QD (AGP),
ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
ATI Radeon 9100 QM (AGP), ATI Radeon 7500 QW (AGP/PCI),
ATI Radeon 7500 QX (AGP/PCI), ATI Radeon VE/7000 QY (AGP/PCI),
ATI Radeon VE/7000 QZ (AGP/PCI), ATI ES1000 515E (PCI),
ATI Radeon Mobility X300 (M22) 5460 (PCIE),
ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R423) UH (PCIE),
ATI Radeon X800PRO (R423) UI (PCIE),
ATI Radeon X800LE (R423) UJ (PCIE),
ATI Radeon X800SE (R423) UK (PCIE),
ATI Radeon X800 XTP (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 (R430) (PCIE),
ATI FireGL V7100 (R423) (PCIE), ATI FireGL V5100 (R423) UQ (PCIE),
ATI FireGL unknown (R423) UR (PCIE),
ATI FireGL unknown (R423) UT (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility Radeon X700 XL (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Radeon X550XTX 5657 (PCIE), ATI Radeon 9100 IGP (A5) 5834,
ATI Radeon Mobility 9100 IGP (U3) 5835,
ATI Radeon XPRESS 200 5954 (PCIE),
ATI Radeon XPRESS 200M 5955 (PCIE), ATI Radeon 9250 5960 (AGP),
ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
ATI ES1000 5969 (PCI), ATI Radeon XPRESS 200 5974 (PCIE),
ATI Radeon XPRESS 200M 5975 (PCIE),
ATI Radeon XPRESS 200 5A41 (PCIE),
ATI Radeon XPRESS 200M 5A42 (PCIE),
ATI Radeon XPRESS 200 5A61 (PCIE),
ATI Radeon XPRESS 200M 5A62 (PCIE),
ATI Radeon X300 (RV370) 5B60 (PCIE),
ATI Radeon X600 (RV370) 5B62 (PCIE),
ATI Radeon X550 (RV370) 5B63 (PCIE),
ATI FireGL V3100 (RV370) 5B64 (PCIE),
ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
ATI Radeon Mobility 9200 (M9+) 5C63 (AGP),
ATI Mobility Radeon X800 XT (M28) (PCIE),
ATI Mobility FireGL V5100 (M28) (PCIE),
ATI Mobility Radeon X800 (M28) (PCIE), ATI Radeon X850 5D4C (PCIE),
ATI Radeon X850 XT PE (R480) (PCIE),
ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
ATI Radeon X850 XT (R480) (PCIE),
ATI Radeon X800XT (R423) 5D57 (PCIE),
ATI FireGL V5000 (RV410) (PCIE), ATI Radeon X700 XT (RV410) (PCIE),
ATI Radeon X700 PRO (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X1800,
ATI Mobility Radeon X1800 XT, ATI Mobility Radeon X1800,
ATI Mobility FireGL V7200, ATI FireGL V7200, ATI FireGL V5300,
ATI Mobility FireGL V7100, ATI Radeon X1800, ATI Radeon X1800,
ATI Radeon X1800, ATI Radeon X1800, ATI Radeon X1800,
ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
ATI Mobility Radeon X1400, ATI Radeon X1300/X1550,
ATI Radeon X1550 64-bit, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Radeon X1300, ATI Radeon X1300,
ATI RV505, ATI RV505, ATI FireGL V3300, ATI FireGL V3350,
ATI Radeon X1300, ATI Radeon X1550 64-bit, ATI Radeon X1300/X1550,
ATI Radeon X1600, ATI Radeon X1300/X1550, ATI Mobility Radeon X1450,
ATI Radeon X1300/X1550, ATI Mobility Radeon X2300,
ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
ATI Mobility Radeon X1350, ATI Mobility Radeon X1450,
ATI Radeon X1300, ATI Radeon X1550, ATI Mobility Radeon X1350,
ATI FireMV 2250, ATI Radeon X1550 64-bit, ATI Radeon X1600,
ATI Radeon X1650, ATI Radeon X1600, ATI Radeon X1600,
ATI Mobility FireGL V5200, ATI Mobility Radeon X1600,
ATI Radeon X1650, ATI Radeon X1650, ATI Radeon X1600,
ATI Radeon X1300 XT/X1600 Pro, ATI FireGL V3400,
ATI Mobility FireGL V5250, ATI Mobility Radeon X1700,
ATI Mobility Radeon X1700 XT, ATI FireGL V5200,
ATI Mobility Radeon X1700, ATI Radeon X2300HD,
ATI Mobility Radeon HD 2300, ATI Mobility Radeon HD 2300,
ATI Radeon X1950, ATI Radeon X1900, ATI Radeon X1950,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI AMD Stream Processor, ATI Radeon X1900, ATI Radeon X1950,
ATI RV560, ATI RV560, ATI Mobility Radeon X1900, ATI RV560,
ATI Radeon X1950 GT, ATI RV570, ATI RV570, ATI FireGL V7400,
ATI RV560, ATI Radeon X1650, ATI Radeon X1650, ATI RV560,
ATI Radeon 9100 PRO IGP 7834, ATI Radeon Mobility 9200 IGP 7835,
ATI Radeon X1200, ATI Radeon X1200, ATI Radeon X1200,
ATI Radeon X1200, ATI Radeon X1200, ATI RS740, ATI RS740M, ATI RS740,
ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 XT,
ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro, ATI Radeon HD 2900 GT,
ATI FireGL V8650, ATI FireGL V8600, ATI FireGL V7600,
ATI Radeon 4800 Series, ATI Radeon HD 4870 x2,
ATI Radeon 4800 Series, ATI Radeon HD 4850 x2,
ATI FirePro V8750 (FireGL), ATI FirePro V7760 (FireGL),
ATI Mobility RADEON HD 4850, ATI Mobility RADEON HD 4850 X2,
ATI Radeon 4800 Series, ATI FirePro RV770, AMD FireStream 9270,
AMD FireStream 9250, ATI FirePro V8700 (FireGL),
ATI Mobility RADEON HD 4870, ATI Mobility RADEON M98,
ATI Mobility RADEON HD 4870, ATI Radeon 4800 Series,
ATI Radeon 4800 Series, ATI FirePro M7750, ATI M98, ATI M98, ATI M98,
ATI Mobility Radeon HD 4650, ATI Radeon RV730 (AGP),
ATI Mobility Radeon HD 4670, ATI FirePro M5750,
ATI Mobility Radeon HD 4670, ATI Radeon RV730 (AGP),
ATI RV730XT [Radeon HD 4670], ATI RADEON E4600,
ATI Radeon HD 4600 Series, ATI RV730 PRO [Radeon HD 4650],
ATI FirePro V7750 (FireGL), ATI FirePro V5700 (FireGL),
ATI FirePro V3750 (FireGL), ATI Mobility Radeon HD 4830,
ATI Mobility Radeon HD 4850, ATI FirePro M7740, ATI RV740,
ATI Radeon HD 4770, ATI Radeon HD 4700 Series, ATI Radeon HD 4770,
ATI FirePro M5750, ATI RV610, ATI Radeon HD 2400 XT,
ATI Radeon HD 2400 Pro, ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000,
ATI RV610, ATI Radeon HD 2350, ATI Mobility Radeon HD 2400 XT,
ATI Mobility Radeon HD 2400, ATI RADEON E2400, ATI RV610,
ATI FireMV 2260, ATI RV670, ATI Radeon HD3870,
ATI Mobility Radeon HD 3850, ATI Radeon HD3850,
ATI Mobility Radeon HD 3850 X2, ATI RV670,
ATI Mobility Radeon HD 3870, ATI Mobility Radeon HD 3870 X2,
ATI Radeon HD3870 X2, ATI FireGL V7700, ATI Radeon HD3850,
ATI Radeon HD3690, AMD Firestream 9170, ATI Radeon HD 4550,
ATI Radeon RV710, ATI Radeon RV710, ATI Radeon RV710,
ATI Radeon HD 4350, ATI Mobility Radeon 4300 Series,
ATI Mobility Radeon 4500 Series, ATI Mobility Radeon 4500 Series,
ATI FirePro RG220, ATI Mobility Radeon 4330, ATI RV630,
ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
ATI FireGL V3600, ATI Radeon HD 2600 LE,
ATI Mobility FireGL Graphics Processor, ATI Radeon HD 3470,
ATI Mobility Radeon HD 3430, ATI Mobility Radeon HD 3400 Series,
ATI Radeon HD 3450, ATI Radeon HD 3450, ATI Radeon HD 3430,
ATI Radeon HD 3450, ATI FirePro V3700, ATI FireMV 2450,
ATI FireMV 2260, ATI FireMV 2260, ATI Radeon HD 3600 Series,
ATI Radeon HD 3650 AGP, ATI Radeon HD 3600 PRO,
ATI Radeon HD 3600 XT, ATI Radeon HD 3600 PRO,
ATI Mobility Radeon HD 3650, ATI Mobility Radeon HD 3670,
ATI Mobility FireGL V5700, ATI Mobility FireGL V5725,
ATI Radeon HD 3200 Graphics, ATI Radeon 3100 Graphics,
ATI Radeon HD 3200 Graphics, ATI Radeon 3100 Graphics,
ATI Radeon HD 3300 Graphics, ATI Radeon HD 3200 Graphics,
ATI Radeon 3000 Graphics, SUMO, SUMO, SUMO2, SUMO2, SUMO2, SUMO2,
SUMO, SUMO, SUMO2, SUMO, SUMO, SUMO, SUMO, SUMO, ATI Radeon HD 4200,
ATI Radeon 4100, ATI Mobility Radeon HD 4200,
ATI Mobility Radeon 4100, ATI Radeon HD 4290, ATI Radeon HD 4250,
AMD Radeon HD 6310 Graphics, AMD Radeon HD 6310 Graphics,
AMD Radeon HD 6250 Graphics, AMD Radeon HD 6250 Graphics,
AMD Radeon HD 6300 Series Graphics,
AMD Radeon HD 6200 Series Graphics, PALM, PALM, PALM, CYPRESS,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter, AMD Firestream 9370,
AMD Firestream 9350, ATI Radeon HD 5800 Series,
ATI Radeon HD 5800 Series, ATI Radeon HD 5800 Series,
ATI Radeon HD 5800 Series, ATI Radeon HD 5900 Series,
ATI Radeon HD 5900 Series, ATI Mobility Radeon HD 5800 Series,
ATI Mobility Radeon HD 5800 Series,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter,
ATI Mobility Radeon HD 5800 Series, ATI Radeon HD 5700 Series,
ATI Radeon HD 5700 Series, ATI Radeon HD 6700 Series,
ATI Radeon HD 5700 Series, ATI Radeon HD 6700 Series,
ATI Mobility Radeon HD 5000 Series,
ATI Mobility Radeon HD 5000 Series, ATI Mobility Radeon HD 5570,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter, ATI Radeon HD 5670,
ATI Radeon HD 5570, ATI Radeon HD 5500 Series, REDWOOD,
ATI Mobility Radeon HD 5000 Series,
ATI Mobility Radeon HD 5000 Series, ATI Mobility Radeon Graphics,
ATI Mobility Radeon Graphics, CEDAR,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter, ATI FirePro 2270, CEDAR,
ATI Radeon HD 5450, CEDAR, CEDAR, CAYMAN, CAYMAN, CAYMAN, CAYMAN,
CAYMAN, CAYMAN, CAYMAN, CAYMAN, CAYMAN, CAYMAN,
AMD Radeon HD 6900 Series, AMD Radeon HD 6900 Series, CAYMAN, CAYMAN,
CAYMAN, AMD Radeon HD 6900M Series, Mobility Radeon HD 6000 Series,
BARTS, BARTS, Mobility Radeon HD 6000 Series,
Mobility Radeon HD 6000 Series, BARTS, BARTS, BARTS, BARTS,
AMD Radeon HD 6800 Series, AMD Radeon HD 6800 Series,
AMD Radeon HD 6700 Series, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS,
TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS,
TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS,
CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS,
CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, ARUBA, ARUBA,
ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA,
ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA,
ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA,
ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, TAHITI, TAHITI, TAHITI, TAHITI,
TAHITI, TAHITI, TAHITI, TAHITI, TAHITI, TAHITI, TAHITI, TAHITI,
TAHITI, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN,
PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN,
VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE,
VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE,
VERDE, VERDE, VERDE, OLAND, OLAND, OLAND, OLAND, OLAND, OLAND, OLAND,
OLAND, OLAND, OLAND, OLAND, OLAND, OLAND, HAINAN, HAINAN, HAINAN,
HAINAN, HAINAN, HAINAN, BONAIRE, BONAIRE, BONAIRE, BONAIRE, BONAIRE,
BONAIRE, BONAIRE, BONAIRE, KABINI, KABINI, KABINI, KABINI, KABINI,
KABINI, KABINI, KABINI, KABINI, KABINI, KABINI, KABINI, KABINI,
KABINI, KABINI, KABINI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI,
KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI,
KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI,
HAWAII, HAWAII, HAWAII, HAWAII, HAWAII, HAWAII, HAWAII, HAWAII,
HAWAII, HAWAII, HAWAII, HAWAII
[ 224.023] (++) using VT number 1
[ 224.044] (II) [KMS] Kernel modesetting enabled.
[ 224.046] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics
[ 224.046] (--) intel(0): CPU: x86-64, sse2, sse3, ssse3, sse4.1, sse4.2
[ 224.046] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 224.046] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 224.046] (==) intel(0): RGB weight 888
[ 224.046] (==) intel(0): Default visual is TrueColor
[ 224.046] (**) intel(0): Framebuffer tiled
[ 224.046] (**) intel(0): Pixmaps tiled
[ 224.046] (**) intel(0): "Tear free" disabled
[ 224.046] (**) intel(0): Forcing per-crtc-pixmaps? no
[ 224.046] (II) intel(0): Output LVDS2 has no monitor section
[ 224.047] (--) intel(0): Found backlight control interface acer-wmi (type 'platform') for output LVDS2
[ 224.047] (II) intel(0): Output VGA2 has no monitor section
[ 224.047] (II) intel(0): Output VIRTUAL1 has no monitor section
[ 224.047] (--) intel(0): Output LVDS2 using initial mode 1366x768 on pipe 0
[ 224.047] (==) intel(0): DPI set to (96, 96)
[ 224.047] (II) Loading sub module "dri2"
[ 224.047] (II) LoadModule: "dri2"
[ 224.047] (II) Module "dri2" already built-in
[ 224.047] (==) RADEON(G0): Depth 24, (--) framebuffer bpp 32
[ 224.047] (II) RADEON(G0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[ 224.047] (==) RADEON(G0): Default visual is TrueColor
[ 224.047] (==) RADEON(G0): RGB weight 888
[ 224.047] (II) RADEON(G0): Using 8 bits per RGB (8 bit DAC)
[ 224.047] (--) RADEON(G0): Chipset: "ATI Mobility Radeon HD 5000 Series" (ChipID = 0x68e0)
[ 224.047] (II) Loading sub module "dri2"
[ 224.047] (II) LoadModule: "dri2"
[ 224.047] (II) Module "dri2" already built-in
[ 224.047] (II) Loading sub module "exa"
[ 224.047] (II) LoadModule: "exa"
[ 224.047] (II) Loading /usr/lib/xorg/modules/libexa.so
[ 224.068] (II) Module exa: vendor="X.Org Foundation"
[ 224.068] compiled for 1.15.1, module version = 2.6.0
[ 224.068] ABI class: X.Org Video Driver, version 15.0
[ 224.068] (II) RADEON(G0): KMS Color Tiling: enabled
[ 224.068] (II) RADEON(G0): KMS Color Tiling 2D: enabled
[ 224.068] (II) RADEON(G0): KMS Pageflipping: enabled
[ 224.068] (II) RADEON(G0): SwapBuffers wait for vsync: enabled
[ 224.070] (II) RADEON(G0): Output LVDS-1-0 has no monitor section
[ 224.073] (II) RADEON(G0): Output HDMI-1-0 has no monitor section
[ 224.200] (II) RADEON(G0): Output VGA-1-0 has no monitor section
[ 224.202] (II) RADEON(G0): EDID for output LVDS-1-0
[ 224.202] (II) RADEON(G0): Printing probed modes for output LVDS-1-0
[ 224.202] (II) RADEON(G0): Modeline "1366x768"x60.0 69.50 1366 1414 1446 1466 768 771 777 790 -hsync -vsync (47.4 kHz eP)
[ 224.203] (II) RADEON(G0): Modeline "1280x720"x59.9 74.50 1280 1344 1472 1664 720 723 728 748 -hsync +vsync (44.8 kHz)
[ 224.203] (II) RADEON(G0): Modeline "1152x768"x59.8 71.75 1152 1216 1328 1504 768 771 781 798 -hsync +vsync (47.7 kHz)
[ 224.203] (II) RADEON(G0): Modeline "1024x768"x59.9 63.50 1024 1072 1176 1328 768 771 775 798 -hsync +vsync (47.8 kHz)
[ 224.203] (II) RADEON(G0): Modeline "800x600"x59.9 38.25 800 832 912 1024 600 603 607 624 -hsync +vsync (37.4 kHz)
[ 224.203] (II) RADEON(G0): Modeline "848x480"x59.7 31.50 848 872 952 1056 480 483 493 500 -hsync +vsync (29.8 kHz)
[ 224.203] (II) RADEON(G0): Modeline "720x480"x59.7 26.75 720 744 808 896 480 483 493 500 -hsync +vsync (29.9 kHz)
[ 224.203] (II) RADEON(G0): Modeline "640x480"x59.4 23.75 640 664 720 800 480 483 487 500 -hsync +vsync (29.7 kHz)
[ 224.205] (II) RADEON(G0): EDID for output HDMI-1-0
[ 224.330] (II) RADEON(G0): EDID for output VGA-1-0
[ 224.330] (II) RADEON(G0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 224.330] (II) RADEON(G0): mem size init: gart size :3fdee000 vram size: s:20000000 visible:1fba0000
[ 224.330] (II) RADEON(G0): EXA: Driver will allow EXA pixmaps in VRAM
[ 224.330] (==) RADEON(G0): DPI set to (96, 96)
[ 224.330] (II) Loading sub module "fb"
[ 224.330] (II) LoadModule: "fb"
[ 224.330] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 224.340] (II) Module fb: vendor="X.Org Foundation"
[ 224.341] compiled for 1.15.1, module version = 1.0.0
[ 224.341] ABI class: X.Org ANSI C Emulation, version 0.4
[ 224.341] (II) Loading sub module "ramdac"
[ 224.341] (II) LoadModule: "ramdac"
[ 224.341] (II) Module "ramdac" already built-in
[ 224.341] (==) Depth 24 pixmap format is 32 bpp
[ 224.341] (II) RADEON(G0): [DRI2] Setup complete
[ 224.341] (II) RADEON(G0): [DRI2] DRI driver: r600
[ 224.341] (II) RADEON(G0): [DRI2] VDPAU driver: r600
[ 224.342] (II) RADEON(G0): Front buffer size: 3072K
[ 224.342] (II) RADEON(G0): VRAM usage limit set to 465004K
[ 224.350] (==) RADEON(G0): Backing store enabled
[ 224.350] (II) RADEON(G0): Direct rendering enabled
[ 224.350] (II) EXA(256): Driver allocated offscreen pixmaps
[ 224.350] (II) EXA(256): Driver registered support for the following operations:
[ 224.350] (II) Solid
[ 224.350] (II) Copy
[ 224.350] (II) Composite (RENDER acceleration)
[ 224.350] (II) UploadToScreen
[ 224.350] (II) DownloadFromScreen
[ 224.350] (II) RADEON(G0): Acceleration enabled
[ 224.350] (==) RADEON(G0): DPMS enabled
[ 224.350] (==) RADEON(G0): Silken mouse enabled
[ 224.351] (II) RADEON(G0): Set up textured video
[ 224.351] (II) RADEON(G0): [XvMC] Associated with Radeon Textured Video.
[ 224.351] (II) RADEON(G0): [XvMC] Extension initialized.
[ 224.351] (II) RADEON(G0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 224.369] (II) intel(0): SNA initialized with Ironlake (gen5) backend
[ 224.369] (==) intel(0): Backing store enabled
[ 224.369] (==) intel(0): Silken mouse enabled
[ 224.369] (II) intel(0): HW Cursor enabled
[ 224.369] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 224.369] (==) intel(0): DPMS enabled
[ 224.369] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[ 224.369] (II) intel(0): [DRI2] Setup complete
[ 224.369] (II) intel(0): [DRI2] DRI driver: i965
[ 224.369] (II) intel(0): [DRI2] VDPAU driver: i965
[ 224.369] (II) intel(0): direct rendering: DRI2 Enabled
[ 224.369] (==) intel(0): hotplug detection: "enabled"
[ 224.369] (--) RandR disabled
[ 224.493] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 224.493] (II) AIGLX: enabled GLX_ARB_create_context
[ 224.493] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 224.493] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 224.493] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 224.493] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 224.493] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[ 224.493] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[ 224.493] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 224.493] (II) AIGLX: Loaded and initialized i965
[ 224.493] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 224.906] (II) intel(0): switch to mode [email protected] on LVDS2 using pipe 0, position (0, 0), rotation normal, reflection none
[ 231.373] (II) intel(0): Setting screen physical size to 361 x 203
[ 231.680] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[ 231.680] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 231.680] (II) LoadModule: "evdev"
[ 231.680] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 231.703] (II) Module evdev: vendor="X.Org Foundation"
[ 231.703] compiled for 1.15.1, module version = 2.9.0
[ 231.703] Module class: X.Org XInput Driver
[ 231.703] ABI class: X.Org XInput driver, version 20.0
[ 231.703] (II) Using input driver 'evdev' for 'Power Button'
[ 231.703] (**) Power Button: always reports core events
[ 231.703] (**) evdev: Power Button: Device: "/dev/input/event3"
[ 231.703] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 231.703] (--) evdev: Power Button: Found keys
[ 231.703] (II) evdev: Power Button: Configuring as keyboard
[ 231.703] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event3"
[ 231.703] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 231.703] (**) Option "xkb_rules" "evdev"
[ 231.703] (**) Option "xkb_model" "pc104"
[ 231.703] (**) Option "xkb_layout" "us"
[ 231.740] (II) config/udev: Adding input device Video Bus (/dev/input/event14)
[ 231.740] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 231.740] (II) Using input driver 'evdev' for 'Video Bus'
[ 231.740] (**) Video Bus: always reports core events
[ 231.740] (**) evdev: Video Bus: Device: "/dev/input/event14"
[ 231.740] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 231.740] (--) evdev: Video Bus: Found keys
[ 231.740] (II) evdev: Video Bus: Configuring as keyboard
[ 231.740] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input15/event14"
[ 231.741] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 231.741] (**) Option "xkb_rules" "evdev"
[ 231.741] (**) Option "xkb_model" "pc104"
[ 231.741] (**) Option "xkb_layout" "us"
[ 231.742] (II) config/udev: Adding input device Video Bus (/dev/input/event13)
[ 231.742] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 231.742] (II) Using input driver 'evdev' for 'Video Bus'
[ 231.742] (**) Video Bus: always reports core events
[ 231.742] (**) evdev: Video Bus: Device: "/dev/input/event13"
[ 231.742] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 231.742] (--) evdev: Video Bus: Found keys
[ 231.742] (II) evdev: Video Bus: Configuring as keyboard
[ 231.742] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input14/event13"
[ 231.742] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)
[ 231.742] (**) Option "xkb_rules" "evdev"
[ 231.742] (**) Option "xkb_model" "pc104"
[ 231.742] (**) Option "xkb_layout" "us"
[ 231.743] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[ 231.743] (II) No input driver specified, ignoring this device.
[ 231.743] (II) This device may have been added with another device file.
[ 231.743] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)
[ 231.743] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 231.743] (II) Using input driver 'evdev' for 'Sleep Button'
[ 231.743] (**) Sleep Button: always reports core events
[ 231.743] (**) evdev: Sleep Button: Device: "/dev/input/event2"
[ 231.743] (--) evdev: Sleep Button: Vendor 0 Product 0x3
[ 231.743] (--) evdev: Sleep Button: Found keys
[ 231.743] (II) evdev: Sleep Button: Configuring as keyboard
[ 231.743] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3/event2"
[ 231.743] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[ 231.743] (**) Option "xkb_rules" "evdev"
[ 231.743] (**) Option "xkb_model" "pc104"
[ 231.743] (**) Option "xkb_layout" "us"
[ 231.744] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 231.744] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=3 (/dev/input/event8)
[ 231.744] (II) No input driver specified, ignoring this device.
[ 231.744] (II) This device may have been added with another device file.
[ 231.744] (II) config/udev: Adding drm device (/dev/dri/card1)
[ 231.744] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event9)
[ 231.744] (II) No input driver specified, ignoring this device.
[ 231.744] (II) This device may have been added with another device file.
[ 231.745] (II) config/udev: Adding input device HDA Intel MID Mic (/dev/input/event11)
[ 231.745] (II) No input driver specified, ignoring this device.
[ 231.745] (II) This device may have been added with another device file.
[ 231.745] (II) config/udev: Adding input device HDA Intel MID Headphone (/dev/input/event10)
[ 231.745] (II) No input driver specified, ignoring this device.
[ 231.745] (II) This device may have been added with another device file.
[ 231.745] (II) config/udev: Adding input device 1.3M WebCam (/dev/input/event5)
[ 231.745] (**) 1.3M WebCam: Applying InputClass "evdev keyboard catchall"
[ 231.745] (II) Using input driver 'evdev' for '1.3M WebCam'
[ 231.745] (**) 1.3M WebCam: always reports core events
[ 231.745] (**) evdev: 1.3M WebCam: Device: "/dev/input/event5"
[ 231.745] (--) evdev: 1.3M WebCam: Vendor 0x4f2 Product 0xb1d8
[ 231.745] (--) evdev: 1.3M WebCam: Found keys
[ 231.745] (II) evdev: 1.3M WebCam: Configuring as keyboard
[ 231.745] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.0/input/input7/event5"
[ 231.745] (II) XINPUT: Adding extended input device "1.3M WebCam" (type: KEYBOARD, id 10)
[ 231.745] (**) Option "xkb_rules" "evdev"
[ 231.745] (**) Option "xkb_model" "pc104"
[ 231.745] (**) Option "xkb_layout" "us"
[ 231.746] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 231.746] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 231.746] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 231.746] (**) AT Translated Set 2 keyboard: always reports core events
[ 231.746] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 231.746] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 231.746] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 231.746] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 231.746] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 231.746] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 11)
[ 231.746] (**) Option "xkb_rules" "evdev"
[ 231.746] (**) Option "xkb_model" "pc104"
[ 231.746] (**) Option "xkb_layout" "us"
[ 231.746] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event12)
[ 231.746] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[ 231.746] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 231.746] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "Default clickpad buttons"
[ 231.746] (II) LoadModule: "synaptics"
[ 231.746] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 231.754] (II) Module synaptics: vendor="X.Org Foundation"
[ 231.754] compiled for 1.15.1, module version = 1.8.0
[ 231.754] Module class: X.Org XInput Driver
[ 231.754] ABI class: X.Org XInput driver, version 20.0
[ 231.754] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[ 231.754] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 231.754] (**) Option "Device" "/dev/input/event12"
[ 231.930] (II) synaptics: SynPS/2 Synaptics TouchPad: ignoring touch events for semi-multitouch device
[ 231.930] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5822 (res 79)
[ 231.930] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4766 (res 141)
[ 231.930] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[ 231.930] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 15
[ 231.930] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left right double triple
[ 231.930] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7
[ 231.930] (**) Option "TapButton1" "1"
[ 231.930] (**) Option "TapButton2" "2"
[ 231.930] (**) Option "TapButton3" "3"
[ 231.930] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 231.930] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 232.010] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input6/event12"
[ 232.010] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 12)
[ 232.010] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[ 232.010] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MaxSpeed is now 1.75
[ 232.010] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) AccelFactor is now 0.036
[ 232.010] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 232.010] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[ 232.010] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 232.010] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 232.010] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 232.010] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse0)
[ 232.010] (**) SynPS/2 Synaptics TouchPad: Ignoring device from InputClass "touchpad ignore duplicates"
[ 232.011] (II) config/udev: Adding input device PC Speaker (/dev/input/event4)
[ 232.011] (II) No input driver specified, ignoring this device.
[ 232.011] (II) This device may have been added with another device file.
[ 232.011] (II) config/udev: Adding input device Acer WMI hotkeys (/dev/input/event6)
[ 232.011] (**) Acer WMI hotkeys: Applying InputClass "evdev keyboard catchall"
[ 232.011] (II) Using input driver 'evdev' for 'Acer WMI hotkeys'
[ 232.011] (**) Acer WMI hotkeys: always reports core events
[ 232.011] (**) evdev: Acer WMI hotkeys: Device: "/dev/input/event6"
[ 232.012] (--) evdev: Acer WMI hotkeys: Vendor 0 Product 0
[ 232.012] (--) evdev: Acer WMI hotkeys: Found keys
[ 232.012] (II) evdev: Acer WMI hotkeys: Configuring as keyboard
[ 232.012] (**) Option "config_info" "udev:/sys/devices/virtual/input/input8/event6"
[ 232.012] (II) XINPUT: Adding extended input device "Acer WMI hotkeys" (type: KEYBOARD, id 13)
[ 232.012] (**) Option "xkb_rules" "evdev"
[ 232.012] (**) Option "xkb_model" "pc104"
[ 232.012] (**) Option "xkb_layout" "us"
[ 232.013] (II) config/udev: Adding input device Acer BMA150 accelerometer (/dev/input/event7)
[ 232.013] (II) No input driver specified, ignoring this device.
[ 232.013] (II) This device may have been added with another device file.
[ 232.013] (II) config/udev: Adding input device Acer BMA150 accelerometer (/dev/input/js0)
[ 232.013] (II) No input driver specified, ignoring this device.
[ 232.013] (II) This device may have been added with another device file.
[ 239.383] (II) AIGLX: Suspending AIGLX clients for VT switch
[ 240.099] (II) evdev: Acer WMI hotkeys: Close
[ 240.099] (II) UnloadModule: "evdev"
[ 240.099] (II) UnloadModule: "synaptics"
[ 240.099] (II) evdev: AT Translated Set 2 keyboard: Close
[ 240.099] (II) UnloadModule: "evdev"
[ 240.099] (II) evdev: 1.3M WebCam: Close
[ 240.099] (II) UnloadModule: "evdev"
[ 240.099] (II) evdev: Sleep Button: Close
[ 240.099] (II) UnloadModule: "evdev"
[ 240.099] (II) evdev: Video Bus: Close
[ 240.099] (II) UnloadModule: "evdev"
[ 240.099] (II) evdev: Video Bus: Close
[ 240.099] (II) UnloadModule: "evdev"
[ 240.099] (II) evdev: Power Button: Close
[ 240.099] (II) UnloadModule: "evdev"
[ 240.101] (WW) xf86CloseConsole: KDSETMODE failed: Input/output error
[ 240.101] (WW) xf86CloseConsole: VT_GETMODE failed: Input/output error
[ 240.101] (EE)
Fatal server error:
[ 240.102] (EE) xf86CloseConsole: VT_ACTIVATE failed: Input/output error
[ 240.102] (EE)
[ 240.102] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 240.102] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 240.102] (EE)
[ 240.102] (EE)
[ 240.102] (EE) Backtrace:
[ 240.102] (EE) 0: /usr/bin/X (xorg_backtrace+0x48) [0x584b08]
[ 240.102] (EE) 1: /usr/bin/X (0x400000+0x1887f9) [0x5887f9]
[ 240.102] (EE) 2: /usr/lib/libpthread.so.0 (0x7f82116cb000+0xf4b0) [0x7f82116da4b0]
[ 240.102] (EE)
[ 240.102] (EE) Segmentation fault at address 0x0
[ 240.102] (EE)
FatalError re-entered, aborting
[ 240.102] (EE) Caught signal 11 (Segmentation fault). Server aborting
[ 240.102] (EE)
EDIT2:
I downgraded to 3.12. Now everything works like a charm, but I wouldn't call downgrading a fix. I am still open for suggestions.
Last edited by Hylleman (2014-06-12 12:16:40)

beneix wrote:
but it just doesn't feel like doing it the way I want...
You should go into the "Display" settings in the Win 7 control panel and have a thorough look through all the settings available there!
Cheers,
Bill
I don't work for Lenovo

My ipad is frozen with a black screen with a picture of a cord leading to the itunes logo.i tried to shut it down and the app;e icon comes out but again the cord leading to the itunes icon keeps on coming out. what should i do ?

My ipad is frozen with a black screen with a picture of a cord leading to the itunes icon. i tried to shut down my ipad but the turn off icon wont show instead the itunes icon with the cord keeps coming out everytime i open my ipad. what should i do ? and i dont want to lose my pictures, videos and other documents in my ipad please help me ....

I hope you have a backup if you don't want to lose your iPad contents. You have to restore the iPad now using iTunes on your computer. That's what the message on the screen means.
Take a look at this.
http://support.apple.com/kb/ht1808

Safari has no graphics just a black screen

Safari has no graphics just a black screen,
This is from launch, the button and window frame are ok but the text look a bit odd on the bookmark bar and the url field is black and the content of the window are just black. I have reinstalled it with a fresh copy from apple.
Help

This is from launch, the button and window frame are ok but the text look a bit odd on the bookmark bar and the url field is black and the content of the window are just black.
Okay ... that is usually caused by a problem that also makes the iTunes Store go black too. So even though Drgoo's post about fixing it in the following post is about fixing the iTunes issue, fingers crossed it should also help with your Safari problem too:
http://discussions.apple.com/message.jspa?messageID=10390276#10390276

Boot Camp Windows 7 Black Screen After Graphic Driver Installation

Hi,
I have MacBook air (2012 model i think). I tried to install windows 7 64 bit using bootcamp. On the first windows boot and before installing boot camp drivers windows was fine. After installing bootcamp drivers and windows restart the windows came up to a black screen and stuck forever. When I uninstall graphic driver (intel HD 4000), windows is good again. Tried to reinstall different graphic drivers versions - didn't work. searched internet everywhere and didn't find any solution.
please help!

I have solved this issue now but seem to have encountered another one. I solved the above issue simply by keep on trying time and time again, partitioning the hard drive and trying to install windows 7.
Anyway, I have encountered this error: windows setup could not apply the configuration set. The WINDOWS folder cannot be found.
Please help!

Onboard and PCI-E Graphics shows blinking black screen on 8.1

I have a homebrewed 3rd Gen Core i5 on an Intel DQ77MK motherboard which has onboard graphics. I also have an nVidia Quadro FX 3500 PCI-E graphics cards.
The Quadro has two DVI outputs connected to two monitors, I connected a third to the onboard graphics. So I have three monitors.
This worked fine with Windows 7. I go to install windows 8.1 and I turned off auto-updates and all the auto device driver junk. I installed the Intel drivers and the nVidia Drivers and three monitors working fine. I go to update to grab a package to remove
that stupid "SecureBoot isn't configured properly" watermark and I reboot to black screens with a cursor and nothing else. I reboot to the BIOS and turn off the integrated graphics and I can get back in - but I really want my triple monitors.

black screens with a cursor and nothing else.
So, if there is a cursor, it's not really "black", just blank. But to be really clear "cursor" means an underscore at the top of the screen, or something else? I have seen the former myself but don't really know what it means. Also it has
only happened occasionally and I can't remember whether it shows on both of my monitors when it happens? I think that when I have seen that I have had to unplug some other USB devices to get past that symptom. E.g. my usual tricks with Win-P or
Ctrl-Alt-Delete or Shift-F10 etc. did nothing--no beeps and no drive light activity.
A reason that it could be important to know if the underscore appears on all monitors is that sometimes the boot seems to get confused about which monitor is primary, so if both monitors have different attributes (as mine do) then perhaps the symptom
could be understood as the wrong monitor getting the controls that were meant for another?
reboot to the BIOS and turn off the integrated graphics and I can get back in
That sounds like a driver problem but I don't know for which component, e.g. WinPE? Boot Manager? OS? So instead of doing that have you tried using the Advanced Boot Option to use low resolution video (AKA VGA mode)? The BCD allows even
other video related settings. While you are having problems it would be a good idea to turn on the Boot menu prompt, even if you don't have multiple partitions to boot, just to make it easier to use those options. FWIW a surprise for me when I
tried this is that we are not restricted to what drivers the OS can use later. E.g. I just used Win-P once in the OS and could make everything work normally after that.
Another thing that you could try is tracing your boot activity with xbootmgr and then finding out what is different for your two cases.
Good luck
Robert Aldwinckle

HP Pavilion DV3 41700-EE Problem-Black Screen after installing graphic card driver

Hi,
Laptop Model : HP Pavilion DV3 41700-EE Entertainment series.
I download the latest official driver for my lap top from this link : http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-93326-1&cc=us&dlc=en&lc=en&...
After the installation i rebooted my device and after the windows loading i got a black screen ! i went to safe mode and unistall the video card and also it's driver from device manager and when i came back the black screen was gone but i have only my onboard Integ graphic which is very slow.
also i went to AMD web site and get AMD Catalyst from their web site but nothing happened after the installation and i think they don't provide an appropriate driver for my lap top.
i also tries to go to device manager and with right click on my display adapter and update driver point to the display driver location on my syste but this time it does not take time the black screen after restart, and in the middle of installation i got a black screen.
Also i upgraded my BIOS Firmware from 16 to 24, but nothing changed.
i just wanna know is it a software problem or hardware problem ? how can i find out that ?
also i don't want this switchy manner and i don't care about the power efficency. i just want to my device work on maximum performance.
What you suggest i do ?

Use the recovery manager to reinstall the original AMD graphics driver and Catalyst Control center.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Systemd graphical.target leads to black screen

Similar Messages

Maybe you are looking for