T1/E1 card not detected on the Router
I ordered a router for CME,with a T1/EI (1MFT-T1/E1) card. I have just realized that when I try to run the controller command, it says unrecognized command. When i show run,I dont see the controller interface. How ever, i tried another E1 card (1MFT-E1) on the same router, and it saw it.
Please advice, is there any command to activate the 1MFT-T1/E1 card?
How do confirm if its bad?
I recently ordered a 1MFT-T1/E1 card as well, and was in the same boat. When you do a show running, it will say something like "you must select the card type in slot 0" or whatever. This command is necessary to tell the card what mode to run in since it is both a T1 and E1.
Try this if you haven't already done so.
card type e1
If you've already done this, let us know and we can start helping out.
Lelio
Please rate helpful posts
Similar Messages
-
How long it takes to repair an Apple iPad with the error "sim card not detected". The ipad is in Apple since 19 January and still has the status "Repair in Progress".
There is no way any fellow user here can know anything specific about your repair status. You will need to call Apple and ask them yourself.
-
Hello everyone,
I just updated my 3GS from iOS 5.0.0 to 5.0.1
Since the update, Itunes says that no SIM card is detected, and the iPhone says that it cannot be activated. It also obviously does not detect any network.
I tried restarting the phone several times, removing the SIM card several times, but it did not change anything, the SIM is still not detected.You do not need to keep posting the same thing over and over again.
Look to the right side of this page at "more Like this" or do a forum search. -
Old Airport card not recognizing Apple Airport Router.
Hello there,
I've just been given an old G4 (digital audio) to use for university and after doing some research brought an old Airport card off of ebay.
After putting into the relevant slot and plugging it in, it started to recognize all of my neighbor's networks, but not my own which is run from an Apple Router!
I also have a faster G4 iBook which uses the airport extreme card and it can find it no problem?
Is it a lost cause trying to get such an old card trying to find the router? I'd rather avoid having to 'borrow' my neighbor's connection if I can help it.Hi duane,
Thanks for the prompt reply.
My airport base station has just been reset and is currently using the default channel (which i believe is 2) and the airport card still is refusing to notice it. -
After software Update (2006-07), airport can not connect to the router
Hi,
I installed the software update 2006-07. Afterwards the airport extreme can not connect to the router anymore (NETGEAR). I use a WEP key, but even if I type the WEP Key, the airport does not succeed to the router anymore... I called Apple Care and they wanted that I install the firmware restoration. But even I didn't succeed to install the firmware restoration. On the firmware restoration web page (http://www.apple.com/support/downloads/firmwarerestorationcd12.html) is written that I have to turn on the computer and continue holding down the power button until the LED blinks rapidly followed immediately by a successive series of blinks (3 quick blinks, 3 slow blinks, 3 quick blinks). But after the LED blinks, there is not the successive series of blinks...
I know there is 2 questions in one message, but could you please help?
Thanks in advance.
Best regards,
Eric
MacBook Pro Intel Core 2 Duo Mac OS X (10.4.8)http://forums.macosxhints.com/showthread.php?p=337100
Exactly the same problems as mentioned here kernel panics, etc. How could this have passed Apple Quality Checks?
Tue Dec 5 09:26:34 2006
panic(cpu 0 caller 0x000A8800): Uncorrectable machine check: pc = 000000003931288C, msr = 0000000000149030, dsisr = 40000000, dar = 000000003A207F7E
AsyncSrc = 0000000000000000, CoreFIR = 0000000000000000
L2FIR = 0000000000000000, BusFir = 0000000000000000
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000A8800 0x000A7A90 0x000AB780
Proceeding back via exception chain:
Exception state (sv=0x39D1B780)
PC=0x3931288C; MSR=0x00149030; DAR=0x3A207F7E; DSISR=0x40000000; LR=0x39312858; R1=0x2285BA10; XCP=0x00000008 (0x200 - Machine check)
Backtrace:
0x39312848 0x393139B8 0x39333874 0x393336BC 0x393332F0 0x3933313C
0x002D124C 0x393314AC 0x39332774 0x002EB838 0x0008C6A4 0x0002921C 0x000233F8 0x000ABAAC
0x00000000
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.AppleAirPort2(405.1)@0x392f4000
dependency: com.apple.iokit.IONetworkingFamily(1.5.0)@0x386e6000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x32922000
Exception state (sv=0x39D3A780)
PC=0x9000AB48; MSR=0x0200F030; DAR=0x003B8000; DSISR=0x42000000; LR=0x9000AA9C; R1=0xBFFFCCA0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Just by enabling the airport express card. Now I wonder what triggers the bug. Because I rebooted several times after the update. One thing I did see was the signal strength going less strong in the past days. Since today I cannot use it at all. -
My Z30 just few months old, sim card not detect, can someone help? thanks a lot..
Hello,
Have you tested the SIM in another device? Have you tested another known-good SIM in this device? Is there an error message? Has it ever worked?
Let us know. -
3x GPU Cards on 990FXA-GD80. Third card not detected in OS.
I have three Sapphire Radeon 7950 plugged into each 16x PCIe slot. The third card is not detected by the OS in any way. The two other cards are detected just fine.
What can I do? All items are brand new. I have not used the CrossFireX cable, since I won't be using the cards together, but for individual folding.
Thanks for any helpok so one of 4 things is happening here!
1: you could have a power issue on the board and the 3rd slot is not getting enougth power through the PCI_E slot to use the card (suggestion you remove the Middle Card and see if the 3rd slot comes Online?)
2: your PSU could be too weak to power the card (what PSU do you have? as i would suggest that you need a single +12v rail with 60A and a 750W minimum Rating overall)
3: possible defective Card (have you tried it in one of the other slots to see if its visible there?)
4: your CPU has a issue and is limiting the lanes as AMD GPU's like at least 8 Lanes Available (slim possibility but it should have enougth lanes to use all 3 cards)
i would suggest you run the 3 checks i have suggested in the () above and see what happens! also try to make sure the 3rd card is seated properly as it may look right but may not be connecting to the PCI_E slot Correctly! -
# Question
Since updating to Firefox 3.6.15, I can no longer print coupons from SmartSource. The error message is that Java is not detected. The check box is longer showing in the Options/Content of this version of Firefox, so I can not enable it.Same PC as I used to post the question. When I go to the "plug in check" page, it shows I am up to date and it is not disabled.
Java(TM) Platform SE 6 U24
Next Generation Java Plug-in 1.6.0_24 for Mozilla browsers 1.6.0.24 -
Aironet 1600 - A response was not received from the router or access point
Hi,
I'm trying to set up a wireless network with multiple SSID's. The new network only has CISCO products (router, switches). For the moment I'm trying to connect to 1 SSID (Windekind.Gast). the SSID is visible but when connecting devices have te folowing error message in the log:
Connection status summary
Connection started at: 2015-02-17 09:55:49-951
Profile match: Success
Pre-Association: Success
Association: Fail
Security and Authentication: Not started
Root cause:
Wireless association to "Windekind.Gast" failed
A response was not received from the router or access point.
Detailed root cause:
Wireless association to this network failed. Windows did not receive any response from the wireless router or accesspoint.
The signal is perfect (I'm only a few feet away from the AP).
To make sure there is no dhcp problem I tested the swich port in access mode for vlan 30 which supplied an IP correctly. I'm really not seeing the problem and searched the web for days now! Any help would be very much appreciated!
Below the config of the access point (done via de web interface).
! Last configuration change at 05:30:28 UTC Mon Mar 1 1993
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AP002-C
logging rate-limit console 9
enable secret 5 $1$Bxv3$Of8o5..8v6gzIiAe2tXlh/
no aaa new-model
no ip cef
dot11 syslog
dot11 vlan-name Windekind.Directie vlan 50
dot11 vlan-name Windekind.Gast vlan 30
dot11 vlan-name Windekind.Klasnet vlan 40
dot11 ssid Windekind.Directie
vlan 50
band-select
authentication open
mobility network-id 50
dot11 ssid Windekind.Gast
vlan 30
band-select
authentication open
authentication key-management wpa version 2
mbssid guest-mode
mobility network-id 30
wpa-psk ascii 7 14201B05080121222A2C6A6D63
dot11 ssid Windekind.Klasnet
vlan 40
band-select
mobility network-id 40
crypto pki token default removal timeout 0
username Cisco password 7 112A1016141D
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 2
stbc
beamform ofdm
mbssid
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel 2452
no preamble-short
station-role root
payload-encapsulation dot1h
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 4
no dfs band block
stbc
beamform ofdm
mbssid
speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel dfs
station-role root
payload-encapsulation dot1h
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 spanning-disabled
no bridge-group 30 source-learning
interface GigabitEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 spanning-disabled
no bridge-group 40 source-learning
interface GigabitEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 spanning-disabled
no bridge-group 50 source-learning
interface BVI1
ip address 10.0.0.81 255.255.255.0
no ip route-cache
ip default-gateway 10.0.0.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging facility user
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
endHi Rasika
thanks for the reply! 10.0.0.81 belongs to vlan 1. I changed the config as suggested but no luck.. (same problems are logged in the event viewer). the ap is connected to a switchport in trunk mode and vlan 1 is the native lan (untagged). the port also is joined to vlan 30 (and others).
Below the new config. Hope you can see an error..
! Last configuration change at 22:56:10 UTC Thu Apr 1 1993
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AP002-C
logging rate-limit console 9
enable secret 5 $1$Bxv3$Of8o5..8v6gzIiAe2tXlh/
no aaa new-model
no ip cef
dot11 syslog
dot11 vlan-name Default vlan 1
dot11 vlan-name Windekind.Directie vlan 50
dot11 vlan-name Windekind.Gast vlan 30
dot11 vlan-name Windekind.Klasnet vlan 40
dot11 ssid Windekind.Directie
vlan 50
band-select
authentication open
mobility network-id 50
dot11 ssid Windekind.Gast
vlan 30
band-select
authentication open
authentication key-management wpa version 2
mbssid guest-mode
mobility network-id 30
wpa-psk ascii 7 14201B05080121222A2C6A6D63
dot11 ssid Windekind.Klasnet
vlan 40
band-select
mobility network-id 40
crypto pki token default removal timeout 0
username Cisco password 7 112A1016141D
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 2
stbc
beamform ofdm
mbssid
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
no preamble-short
channel 2452
station-role root
payload-encapsulation dot1h
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 4
no dfs band block
stbc
beamform ofdm
mbssid
speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel dfs
station-role root
payload-encapsulation dot1h
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 spanning-disabled
no bridge-group 30 source-learning
interface GigabitEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 spanning-disabled
no bridge-group 40 source-learning
interface GigabitEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 spanning-disabled
no bridge-group 50 source-learning
interface BVI1
ip address 10.0.0.81 255.255.255.0
no ip route-cache
ip default-gateway 10.0.0.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging facility user
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
end
t -
HPE-475a wireless card not detecting networks
For the last few months, every now and again, my computer would start up but be unable to detect any wireless networks. It seemed that simply shutting it back down for an hour or so would magically resolve it. Some research at the time suggested that it was unable to detect a driver for some reason.
However, today, several hours of the computer being off has not resolved the issue, and the device manager suggests that the card is working fine, without any driver troubles. Perhaps I am looking at the wrong thing.
I have been able to connect using an old wireless dongle, but I don't want that to be the permanent solution.
What can I do to better diagnose and resolve the issue? I've searched a bit but couldn't find anything which seemed specific to this situation.
Product name: HPE-475a
Product number: BU082AA#ABG
Operating system: Windows 7 Home Premium Service Pack 1
Error messages: None.
Recent changes: None.
Troubleshooting performed: Attempted to "Diagnose" through Network Connections. It suggested to check the router. The router is fine, multiple other devices are able to connect. Diagnostics then says it cannot resolve the connectivity issue.
Thanks in advance!
- Phil.
This question was solved.
View Solution.Hi,
If WIFI was working fine using the current router then the mixed mode setting is not the problem.
If Device Manager shows no errors and you cannot connect using wireless then the WIFI adapter card is, most likely, the problem.
Good to hear you have an extended warranty.
Contact HP Support.
Jaco
Errare humanum est. -
VIC3-4FXO/DID module not detect in 2801 Router.
Hi Team,
I have Cisco 2801 router with 2 DSP 16 Channel, 128 MB DRAM and 128 MB flash. I am using IOS c2801-spservicesk9-mz.124-3i but the VIC3-4FXO/DID module is not detected. I tried to upgrade the IOS to 15.0 and 15.1 but the router is not boot up due to insufficient memory. In that IOS the FXO card is detected. I checked the data sheet of both router and FXO card it support 12.4T IOS but when I upload the IOS and try to boot same problem I have faced (router not boot due to insufficient memory). Kindly help me find out the appropriate IOS to resolve the issue.
Thanks in advance.
Regards,
Manas RanjanVIC3-4FXO card is not supported in 2801 according to table4
Table 4. Software and Memory Requirements for Voice/Fax Network Modules and Voice Interface Cards
Product
Cisco 2800 Series
Cisco 3800 Series
Cisco 2900 and 3900 Series
NM-HD-1V
NM-HD-2V
NM-HD-2VE
• Cisco IOS Software
• Release 12.3(8)T4
• "IP Voice" images
• Cisco IOS Software
• Release 12.3(11)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VIC2-2FXO
VIC2-4FXO
VIC2-2BRI-NT/TE
• Cisco IOS Software
• Release 12.3(8)T4
• "IP Voice" images
• Cisco IOS Software
• Release 12.3(11)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VWIC2-xMFT-xx
• Cisco IOS Software
• Release 12.3(14)T
• "IP Voice" images
• Cisco IOS Software
• Release 12.3(14)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VIC3-2E/M
• Cisco IOS Software
• Release 12.4(15)XW or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software
• Release 12.4(15)XW or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VIC3-2FXS/DID
VIC3-2FXS-E/DID
VIC3-4FXS/DID
• Cisco IOS Software
• Release 12.4(15)XZ or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software
• Release 12.4(15)XZ or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images -
[root@kyriotetes ~]# dmesg|grep b43
[root@kyriotetes ~]# dmesg|grep bcm43
bcm43xx driver
HI dear colleagues,
I have an ASUS PCI WLAN card with Broadcom BCM4318 chipset. It works fine with WIndows 7. However, EL5 does not detect it, so I have to connect thru cable to my router modem. According to web sources the correct driver should be b43 for the chipset.
I executed lspci -vnn | grep 14e4 for the device, here are the results. Seemingly bcm43xx is installed, connected but no communication. Do I really need b43? If so, how to get and install it?
Thank you, regards,
Miklos HERBOLY
Command output
bcm43xx: Chip ID 0x4318, rev 0x2
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243
bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243
bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243
bcm43xx: PHY connected
bcm43xx: Detected PHY: Analog: 3, Type 2, Revision 7
bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev: 8)
bcm43xx: Radio initialized
bcm43xx: Radio initialized
[root@kyriotetes ~]#OEL is intended for a server environment and its wireless support is poor. If your card is detected great, but adding wireless support is not a priority. Remember that laptops, especially, use cutting-edge hardware to reduce manufacturing costs and that the whole purpose of an enterprise distribution is to provide stability on its supported platforms: updates are churn.
However, OEL will run perfectly fine as a virtual machine, so run Windows 7 to get the hardware support and then run OEL under maybe VirtualBox. -
PCMCIA Realtek Ethernet card not detected
Hi, I'm trying to use a PCMCIA Etherner Card with Realtek chip.
If the card it's already plugged when booting, Udev takes 180000 ms to finish and the card doesn't work. If it's plugged while booted, dmesg shows that there's a "something" at SmartCardBus but, again, card doesn't get recognized.
"Ifconfig -a" shows nothing, and I know the card works 'cause I've tryed with an Ubuntu cd and the cards works perfect. I've looked for the modules, and 8139too & 8139cp where loaded, wich I've tryed in arch and still doesn't work, It also detects the same hardware with lspci (Arch detects the Cardbus but not the realtek card, Ubuntu detects both) and lspcmcia.
Ubuntu is using kernel 2.6.27-7 and Arch 2.6.28.
hwd -e:
1217:7113 CardBus bridge: 02 Micro, Inc. module:yanta_cardbus
OZ711EC1 SmartCardBus Controller
lspmcia:
Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:02:01.0)
CardBus card -- see "lspci" for more information
Socket 1 Bridge: [yenta_cardbus] (bus ID: 0000:02:01.1)
Socket 1 Device 0: [-- no driver --] (bus ID: 1.0)
lspci:
00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 03)
00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 01)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV250 [Mobility FireGL 9000] (rev 02)
02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5705M Gigabit Ethernet (rev ff)
02:01.0 CardBus bridge: O2 Micro, Inc. OZ711EC1 SmartCardBus Controller (rev 20)
02:01.1 CardBus bridge: O2 Micro, Inc. OZ711EC1 SmartCardBus Controller (rev 20)
02:03.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
dmesg:
int3: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:1e.0/0000:02:03.0/class
Modules linked in: usb_storage joydev ppdev iTCO_wdt iTCO_vendor_support ehci_hcd psmouse uhci_hcd parport_pc lp serio_raw usbcore shpchp pci_hotplug sg video output parport pcspkr ppp_generic intel_agp agpgart pcmcia dcdbas thermal evdev fan button battery ac acpi_cpufreq freq_table processor snd_intel8x0m snd_seq_oss snd_intel8x0 snd_seq_midi_event snd_seq snd_seq_device snd_ac97_codec snd_pcm_oss snd_pcm snd_timer snd_page_alloc snd_mixer_oss snd soundcore ac97_bus ipw2200 ieee80211 ieee80211_crypt tg3 libphy slhc rtc_cmos rtc_core rtc_lib ext3 jbd mbcache sr_mod cdrom yenta_socket rsrc_nonstatic pcmcia_core sd_mod ata_piix ata_generic pata_acpi libata scsi_mod
Pid: 435, comm: pccardd Not tainted (2.6.28-ARCH #1) Inspiron 600m
EIP: 0060:[<c044dce0>] EFLAGS: 00000246 CPU: 0
EIP is at quirk_h12y_1_mmio+0x1/0x26
EAX: de4fc800 EBX: c03cbdc0 ECX: de4fc840 EDX: de4fc800
ESI: c03cc110 EDI: de4fc800 EBP: df8ae400 ESP: df1b9ef4
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process pccardd (pid: 435, ti=df1b8000 task=df1ba000 task.ti=df1b8000)
Stack:
c02192c3 de4fc800 df8ae400 de4fc800 c0216a59 00000200 00000000 c031c93c
de4fc826 c03b3d25 00000000 00000003 00000000 00000000 00000001 df8ae420
de4fc858 00000200 813910ec 00ffffed 00000000 00000000 00000000 df8ae400
Call Trace:
[<c02192c3>] pci_fixup_device+0x63/0xc0
[<c0216a59>] pci_device_add+0x69/0xb0
[<c031c93c>] pci_scan_single_device+0x35c/0x4f0
[<c0216ac3>] pci_scan_slot+0x23/0x80
[<e0bd850f>] cb_alloc+0x1f/0xd4 [pcmcia_core]
[<e0bd4854>] socket_insert+0x124/0x140 [pcmcia_core]
[<e0bd5202>] pccardd+0x202/0x290 [pcmcia_core]
[<e0bd5000>] pccardd+0x0/0x290 [pcmcia_core]
[<c01440f9>] kthread+0x39/0x70
[<c01440c0>] kthread+0x0/0x70
[<c0104d33>] kernel_thread_helper+0x7/0x14
Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
EIP: [<c044dce0>] quirk_h12y_1_mmio+0x1/0x26 SS:ESP 0068:df1b9ef4
---[ end trace 6fe320c81d500dc7 ]---
note: pccardd[435] exited with preempt_count 1
pci 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized radeon 1.29.0 20080528 on minor 0
agpgart-intel 0000:00:00.0: AGP 2.0 bridge
agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
pci 0000:01:00.0: putting AGP V2 device into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 2 usecs
rc.conf:
MODULES=(slhc tg3 ipw2200 ac97_bus snd-mixer-oss snd-pcm-oss snd-page-alloc snd-pcm snd-timer snd snd-ac97-codec snd-intel8x0 snd-intel8x0m soundcore acpi-cpufreq)
DAEMONS=(syslog-ng network netfs dbus hal !crond cpufreq fam avahi-daemon pcmcia)
I've tryed loading: 8139too 8139cp pcmcia_core pcmcia yenta_socket rsrc_nonstatic
The bradcom is the original eth port wich I'm replacing because stop working long time ago (And I also tryed disabling it from BIOS, and it's the same).
I'm mising something that I should load or run? I've googled a lot, but people just plug the card and that's all :-P. Any idea would be welcomed :-).
EDIT: Fix title (PMCIA*)
Last edited by el_zoona (2009-01-22 07:25:00)Nevermind...It's Kernel 2.6.28...I'm a lucky guy, eh? :-(
Booted into Arch Overlod cd and a simple lspci show my shiny new card...Now i'm going to erase my hole system (it was new anyway) and check if a Suy breaks the drivers again. In that case, i should file a bug somewhere, right? -
ATI Graphics card not detected on cold boot, works on warm boot
Hi All,
I hope you can help me out with this.
I'm using Radeon HD7850 with ATI-Catalyst.
The issue is, if I do a cold boot (physically turn off the power, turn back on) the system won't boot into X, only tty.
At this point, a reboot works fine.
Or if I don't turn off the power, just shutdown and reboot (warm boot), it works ok.
Here's the Xorg log on cold boot:
[ 2.226]
X.Org X Server 1.12.4
Release Date: 2012-08-27
[ 2.226] X Protocol Version 11, Revision 0
[ 2.226] Build Operating System: Linux 3.4.8-1-ARCH x86_64
[ 2.226] Current Operating System: Linux dmanPC 3.5.3-1-ARCH #1 SMP PREEMPT Sun Aug 26 09:14:51 CEST 2012 x86_64
[ 2.226] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=3766a71b-dbfe-4cc2-b7bd-948878b5da67 ro nomodeset quiet
[ 2.226] Build Date: 27 August 2012 08:04:39AM
[ 2.226]
[ 2.226] Current version of pixman: 0.26.2
[ 2.226] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 2.226] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 2.226] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Sep 28 05:57:41 2012
[ 2.227] (==) Using config file: "/etc/X11/xorg.conf"
[ 2.228] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 2.228] (==) ServerLayout "aticonfig Layout"
[ 2.228] (**) |-->Screen "aticonfig-Screen[0]-0" (0)
[ 2.228] (**) | |-->Monitor "aticonfig-Monitor[0]-0"
[ 2.229] (**) | |-->Device "aticonfig-Device[0]-0"
[ 2.229] (==) Automatically adding devices
[ 2.229] (==) Automatically enabling devices
[ 2.231] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 2.231] Entry deleted from font path.
[ 2.231] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 2.231] Entry deleted from font path.
[ 2.231] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 2.231] Entry deleted from font path.
[ 2.231] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 2.232] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 2.232] Entry deleted from font path.
[ 2.232] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 2.232] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 2.232] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 2.232] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 2.232] (II) Loader magic: 0x7c8b00
[ 2.232] (II) Module ABI versions:
[ 2.232] X.Org ANSI C Emulation: 0.4
[ 2.232] X.Org Video Driver: 12.1
[ 2.232] X.Org XInput driver : 16.0
[ 2.232] X.Org Server Extension : 6.0
[ 2.232] (--) PCI:*(0:7:0:0) 1002:6819:1462:2730 rev 0, Mem @ 0xe0000000/268435456, 0xf7b00000/262144, I/O @ 0x0000c000/256, BIOS @ 0x????????/131072
[ 2.232] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 2.232] (II) "extmod" will be loaded by default.
[ 2.232] (II) "dbe" will be loaded by default.
[ 2.232] (II) "glx" will be loaded by default.
[ 2.232] (II) "record" will be loaded by default.
[ 2.232] (II) "dri" will be loaded by default.
[ 2.232] (II) "dri2" will be loaded by default.
[ 2.232] (II) LoadModule: "extmod"
[ 2.233] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 2.233] (II) Module extmod: vendor="X.Org Foundation"
[ 2.233] compiled for 1.12.4, module version = 1.0.0
[ 2.233] Module class: X.Org Server Extension
[ 2.233] ABI class: X.Org Server Extension, version 6.0
[ 2.233] (II) Loading extension MIT-SCREEN-SAVER
[ 2.233] (II) Loading extension XFree86-VidModeExtension
[ 2.233] (II) Loading extension XFree86-DGA
[ 2.233] (II) Loading extension DPMS
[ 2.233] (II) Loading extension XVideo
[ 2.233] (II) Loading extension XVideo-MotionCompensation
[ 2.233] (II) Loading extension X-Resource
[ 2.233] (II) LoadModule: "dbe"
[ 2.233] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 2.234] (II) Module dbe: vendor="X.Org Foundation"
[ 2.234] compiled for 1.12.4, module version = 1.0.0
[ 2.234] Module class: X.Org Server Extension
[ 2.234] ABI class: X.Org Server Extension, version 6.0
[ 2.234] (II) Loading extension DOUBLE-BUFFER
[ 2.234] (II) LoadModule: "glx"
[ 2.234] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 2.236] (II) Module glx: vendor="Advanced Micro Devices, Inc."
[ 2.236] compiled for 6.9.0, module version = 1.0.0
[ 2.236] (II) Loading extension GLX
[ 2.236] (II) LoadModule: "record"
[ 2.236] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 2.237] (II) Module record: vendor="X.Org Foundation"
[ 2.237] compiled for 1.12.4, module version = 1.13.0
[ 2.237] Module class: X.Org Server Extension
[ 2.237] ABI class: X.Org Server Extension, version 6.0
[ 2.237] (II) Loading extension RECORD
[ 2.237] (II) LoadModule: "dri"
[ 2.237] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 2.237] (II) Module dri: vendor="X.Org Foundation"
[ 2.237] compiled for 1.12.4, module version = 1.0.0
[ 2.237] ABI class: X.Org Server Extension, version 6.0
[ 2.237] (II) Loading extension XFree86-DRI
[ 2.237] (II) LoadModule: "dri2"
[ 2.238] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 2.238] (II) Module dri2: vendor="X.Org Foundation"
[ 2.238] compiled for 1.12.4, module version = 1.2.0
[ 2.238] ABI class: X.Org Server Extension, version 6.0
[ 2.238] (II) Loading extension DRI2
[ 2.238] (II) LoadModule: "fglrx"
[ 2.238] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
[ 2.262] (II) Module fglrx: vendor="FireGL - AMD Technologies Inc."
[ 2.262] compiled for 1.4.99.906, module version = 8.98.2
[ 2.262] Module class: X.Org Video Driver
[ 2.262] (II) Loading sub module "fglrxdrm"
[ 2.262] (II) LoadModule: "fglrxdrm"
[ 2.262] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[ 2.263] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[ 2.263] compiled for 1.4.99.906, module version = 8.98.2
[ 2.263] (II) AMD Proprietary Linux Driver Version Identifier:8.98.2
[ 2.263] (II) AMD Proprietary Linux Driver Release Identifier: 8.982
[ 2.263] (II) AMD Proprietary Linux Driver Build Date: Jul 27 2012 20:37:56
[ 2.263] (++) using VT number 8
[ 2.264] (WW) Falling back to old probe method for fglrx
[ 2.269] (II) Loading PCS database from /etc/ati/amdpcsdb
[ 2.271] (WW) fglrx: No matching Device section for instance (BusID ) found
[ 2.271] (EE) No devices detected.
[ 2.271]
Fatal server error:
[ 2.271] no screens found
[ 2.271]
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 2.271] Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 2.271]
Here's the same log for warm boot:
[ 2.289] (++) using VT number 8
[ 2.290] (WW) Falling back to old probe method for fglrx
[ 2.295] (II) Loading PCS database from /etc/ati/amdpcsdb
[ 2.296] (--) Chipset Supported AMD Graphics Processor (0x6819) found
[ 2.296] (WW) fglrx: No matching Device section for instance (BusID PCI:0@6:0:1) found
[ 2.297] (II) AMD Video driver is running on a device belonging to a group targeted for this release
[ 2.297] (II) AMD Video driver is signed
[ 2.297] (II) fglrx(0): pEnt->device->identifier=0x82b7a0
[ 2.297] (II) fglrx(0): === [xdl_xs112_atiddxPreInit] === begin
[ 2.297] (II) Loading sub module "vgahw"
[ 2.297] (II) LoadModule: "vgahw"
[ 2.298] (II) Loading /usr/lib/xorg/modules/libvgahw.so
[ 2.298] (II) Module vgahw: vendor="X.Org Foundation"
[ 2.298] compiled for 1.12.4, module version = 0.1.0
[ 2.298] ABI class: X.Org Video Driver, version 12.1
[ 2.298] (**) fglrx(0): Depth 24, (--) framebuffer bpp 32
[ 2.298] (II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[ 2.298] (==) fglrx(0): Default visual is TrueColor
[ 2.298] (**) fglrx(0): Option "OpenGLOverlay" "0"
[ 2.298] (**) fglrx(0): Option "DPMS" "true"
[ 2.298] (==) fglrx(0): RGB weight 888
[ 2.298] (II) fglrx(0): Using 8 bits per RGB
[ 2.298] (==) fglrx(0): Buffer Tiling is ON
[ 2.299] (II) Loading sub module "fglrxdrm"
[ 2.299] (II) LoadModule: "fglrxdrm"
[ 2.299] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[ 2.299] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[ 2.299] compiled for 1.4.99.906, module version = 8.98.2
[ 2.299] ukiDynamicMajor: found major device number 251
[ 2.299] ukiDynamicMajor: found major device number 251
[ 2.299] ukiOpenByBusid: Searching for BusID PCI:6:0:0
[ 2.299] ukiOpenDevice: node name is /dev/ati/card0
[ 2.299] ukiOpenDevice: open result is 11, (OK)
[ 2.299] ukiOpenByBusid: ukiOpenMinor returns 11
[ 2.299] ukiOpenByBusid: ukiGetBusid reports PCI:6:0:0
[ 2.299] (**) fglrx(0): NoAccel = NO
[ 2.299] (**) fglrx(0): AMD 2D Acceleration Architecture enabled
[ 2.299] (--) fglrx(0): Chipset: "AMD Radeon HD 7800 Series " (Chipset = 0x6819)
[ 2.299] (--) fglrx(0): (PciSubVendor = 0x1462, PciSubDevice = 0x2730)
[ 2.299] (==) fglrx(0): board vendor info: third party graphics adapter - NOT original AMD
[ 2.299] (--) fglrx(0): Linear framebuffer (phys) at 0xe0000000
[ 2.299] (--) fglrx(0): MMIO registers at 0xf7c00000
[ 2.299] (--) fglrx(0): I/O port at 0x0000c000
[ 2.299] (==) fglrx(0): ROM-BIOS at 0x000c0000
[ 2.300] (II) fglrx(0): AC Adapter is used
[ 2.303] (II) fglrx(0): Primary V_BIOS segment is: 0xc000
[ 2.303] (II) Loading sub module "vbe"
[ 2.303] (II) LoadModule: "vbe"
[ 2.303] (II) Loading /usr/lib/xorg/modules/libvbe.so
[ 2.304] (II) Module vbe: vendor="X.Org Foundation"
[ 2.304] compiled for 1.12.4, module version = 1.1.0
[ 2.304] ABI class: X.Org Video Driver, version 12.1
[ 2.304] (II) fglrx(0): VESA BIOS detected
[ 2.304] (II) fglrx(0): VESA VBE Version 3.0
[ 2.304] (II) fglrx(0): VESA VBE Total Mem: 16384 kB
[ 2.304] (II) fglrx(0): VESA VBE OEM: AMD ATOMBIOS
[ 2.304] (II) fglrx(0): VESA VBE OEM Software Rev: 15.17
[ 2.304] (II) fglrx(0): VESA VBE OEM Vendor: (C) 1988-2010, Advanced Micro Devices, Inc.
[ 2.304] (II) fglrx(0): VESA VBE OEM Product: PITCAIRN
[ 2.304] (II) fglrx(0): VESA VBE OEM Product Rev: 01.00
[ 2.309] (II) fglrx(0): AMD Video BIOS revision 9 or later detected
[ 2.309] (--) fglrx(0): Video RAM: 2097152 kByte, Type: GDDR5
[ 2.309] (II) fglrx(0): PCIE card detected
[ 2.309] (--) fglrx(0): Using per-process page tables (PPPT) as GART.
[ 2.309] (WW) fglrx(0): board is an unknown third party board, chipset is supported
[ 2.311] (II) fglrx(0): Using adapter: 6:0.0.
[ 2.320] (II) fglrx(0): [FB] MC range(MCFBBase = 0xf400000000, MCFBSize = 0x80000000)
[ 2.458] (II) fglrx(0): Interrupt handler installed at IRQ 48.
[ 2.458] (II) fglrx(0): RandR 1.2 support is enabled!
[ 2.458] (II) fglrx(0): RandR 1.2 rotation support is enabled!
[ 2.458] (==) fglrx(0): Center Mode is disabled
[ 2.458] (II) Loading sub module "fb"
[ 2.458] (II) LoadModule: "fb"
[ 2.458] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 2.461] (II) Module fb: vendor="X.Org Foundation"
[ 2.461] compiled for 1.12.4, module version = 1.0.0
[ 2.461] ABI class: X.Org ANSI C Emulation, version 0.4
[ 2.461] (II) Loading sub module "ddc"
[ 2.461] (II) LoadModule: "ddc"
[ 2.461] (II) Module "ddc" already built-in
[ 2.571] (II) fglrx(0): Finished Initialize PPLIB!
[ 2.577] (II) fglrx(0): Output DFP1 using monitor section aticonfig-Monitor[0]-0
[ 2.577] (II) fglrx(0): Output DFP2 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP3 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP4 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP5 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP6 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP7 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP8 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP9 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP10 has no monitor section
[ 2.577] (II) fglrx(0): Output CRT1 has no monitor section
[ 2.578] (II) Loading sub module "ddc"
[ 2.578] (II) LoadModule: "ddc"
[ 2.578] (II) Module "ddc" already built-in
[ 2.578] (II) fglrx(0): Connected Display0: DFP10
[ 2.578] (II) fglrx(0): Display0 EDID data ---------------------------
[ 2.578] (II) fglrx(0): Manufacturer: SAM Model: 524 Serial#: 1280455218
[ 2.578] (II) fglrx(0): Year: 2009 Week: 20
[ 2.578] (II) fglrx(0): EDID Version: 1.3
[ 2.578] (II) fglrx(0): Digital Display Input
[ 2.578] (II) fglrx(0): Max Image Size [cm]: horiz.: 48 vert.: 27
[ 2.578] (II) fglrx(0): Gamma: 2.20
[ 2.578] (II) fglrx(0): DPMS capabilities: Off
[ 2.578] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 2.578] (II) fglrx(0): First detailed timing is preferred mode
[ 2.578] (II) fglrx(0): redX: 0.648 redY: 0.339 greenX: 0.143 greenY: 0.070
[ 2.578] (II) fglrx(0): blueX: 0.282 blueY: 0.603 whiteX: 0.312 whiteY: 0.329
[ 2.578] (II) fglrx(0): Supported established timings:
[ 2.578] (II) fglrx(0): 640x480@60Hz
[ 2.578] (II) fglrx(0): 800x600@56Hz
[ 2.578] (II) fglrx(0): 800x600@60Hz
[ 2.578] (II) fglrx(0): 1024x768@60Hz
[ 2.578] (II) fglrx(0): Manufacturer's mask: 0
[ 2.578] (II) fglrx(0): Supported standard timings:
[ 2.578] (II) fglrx(0): #0: hsize: 1280 vsize 800 refresh: 60 vid: 129
[ 2.578] (II) fglrx(0): #1: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 2.578] (II) fglrx(0): #2: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 2.578] (II) fglrx(0): #3: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 2.578] (II) fglrx(0): #4: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 2.578] (II) fglrx(0): #5: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2.578] (II) fglrx(0): Ranges: V min: 56 V max: 60 Hz, H min: 30 H max: 81 kHz, PixClock max 175 MHz
[ 2.578] (II) fglrx(0): Monitor name: SyncMaster
[ 2.578] (II) fglrx(0): Serial No: HMBS500385
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1920 h_sync: 2448 h_sync_end 2492 h_blank_end 2640 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 74.2 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 74.2 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1280 h_sync: 1720 h_sync_end 1760 h_blank_end 1980 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 27.0 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 720 h_sync: 732 h_sync_end 796 h_blank_end 864 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 576 v_sync: 581 v_sync_end 586 v_blanking: 625 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 27.0 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0
[ 2.578] (II) fglrx(0): Number of EDID sections to follow: 1
[ 2.578] (II) fglrx(0): EDID (in hex):
[ 2.578] (II) fglrx(0): 00ffffffffffff004c2d24053232524c
[ 2.578] (II) fglrx(0): 1413010380301b782a3851a656241248
[ 2.578] (II) fglrx(0): 9a50542308008100814081809500a940
[ 2.578] (II) fglrx(0): b30001010101023a801871382d40582c
[ 2.578] (II) fglrx(0): 4500dd0c1100001e000000fd00383c1e
[ 2.578] (II) fglrx(0): 5111000a202020202020000000fc0053
[ 2.578] (II) fglrx(0): 796e634d61737465720a2020000000ff
[ 2.578] (II) fglrx(0): 00484d42533530303338350a20200168
[ 2.578] (II) fglrx(0): End of Display0 EDID data --------------------
[ 2.578] (II) fglrx(0): EDID for output DFP1
[ 2.578] (II) fglrx(0): EDID for output DFP2
[ 2.578] (II) fglrx(0): EDID for output DFP3
[ 2.578] (II) fglrx(0): EDID for output DFP4
[ 2.578] (II) fglrx(0): EDID for output DFP5
[ 2.578] (II) fglrx(0): EDID for output DFP6
[ 2.578] (II) fglrx(0): EDID for output DFP7
[ 2.578] (II) fglrx(0): EDID for output DFP8
[ 2.578] (II) fglrx(0): EDID for output DFP9
[ 2.578] (II) fglrx(0): EDID for output DFP10
[ 2.578] (II) fglrx(0): Manufacturer: SAM Model: 524 Serial#: 1280455218
[ 2.578] (II) fglrx(0): Year: 2009 Week: 20
[ 2.578] (II) fglrx(0): EDID Version: 1.3
[ 2.578] (II) fglrx(0): Digital Display Input
[ 2.578] (II) fglrx(0): Max Image Size [cm]: horiz.: 48 vert.: 27
[ 2.578] (II) fglrx(0): Gamma: 2.20
[ 2.578] (II) fglrx(0): DPMS capabilities: Off
[ 2.578] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 2.578] (II) fglrx(0): First detailed timing is preferred mode
[ 2.578] (II) fglrx(0): redX: 0.648 redY: 0.339 greenX: 0.143 greenY: 0.070
[ 2.578] (II) fglrx(0): blueX: 0.282 blueY: 0.603 whiteX: 0.312 whiteY: 0.329
[ 2.578] (II) fglrx(0): Supported established timings:
[ 2.578] (II) fglrx(0): 640x480@60Hz
[ 2.578] (II) fglrx(0): 800x600@56Hz
[ 2.578] (II) fglrx(0): 800x600@60Hz
[ 2.578] (II) fglrx(0): 1024x768@60Hz
[ 2.578] (II) fglrx(0): Manufacturer's mask: 0
[ 2.578] (II) fglrx(0): Supported standard timings:
[ 2.578] (II) fglrx(0): #0: hsize: 1280 vsize 800 refresh: 60 vid: 129
[ 2.578] (II) fglrx(0): #1: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 2.578] (II) fglrx(0): #2: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 2.578] (II) fglrx(0): #3: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 2.578] (II) fglrx(0): #4: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 2.578] (II) fglrx(0): #5: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2.578] (II) fglrx(0): Ranges: V min: 56 V max: 60 Hz, H min: 30 H max: 81 kHz, PixClock max 175 MHz
[ 2.578] (II) fglrx(0): Monitor name: SyncMaster
[ 2.578] (II) fglrx(0): Serial No: HMBS500385
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1920 h_sync: 2448 h_sync_end 2492 h_blank_end 2640 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 74.2 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 74.2 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1280 h_sync: 1720 h_sync_end 1760 h_blank_end 1980 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 27.0 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 720 h_sync: 732 h_sync_end 796 h_blank_end 864 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 576 v_sync: 581 v_sync_end 586 v_blanking: 625 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 27.0 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0
[ 2.578] (II) fglrx(0): Number of EDID sections to follow: 1
[ 2.578] (II) fglrx(0): EDID (in hex):
[ 2.578] (II) fglrx(0): 00ffffffffffff004c2d24053232524c
[ 2.578] (II) fglrx(0): 1413010380301b782a3851a656241248
[ 2.578] (II) fglrx(0): 9a50542308008100814081809500a940
[ 2.578] (II) fglrx(0): b30001010101023a801871382d40582c
[ 2.578] (II) fglrx(0): 4500dd0c1100001e000000fd00383c1e
[ 2.578] (II) fglrx(0): 5111000a202020202020000000fc0053
[ 2.578] (II) fglrx(0): 796e634d61737465720a2020000000ff
[ 2.578] (II) fglrx(0): 00484d42533530303338350a20200168
[ 2.579] (II) fglrx(0): Printing probed modes for output DFP10
[ 2.579] (II) fglrx(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "1920x1080"x50.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1776x1000"x50.0 148.50 1776 2304 2348 2640 1000 1004 1009 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1680x1050"x50.0 148.50 1680 2448 2492 2640 1050 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 2.579] (II) fglrx(0): Modeline "1400x1050"x60.0 162.00 1400 1664 1856 2160 1050 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1400x1050"x50.0 148.50 1400 2448 2492 2640 1050 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1600x900"x60.0 162.00 1600 1664 1856 2160 900 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1600x900"x50.0 148.50 1600 2448 2492 2640 900 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x1024"x50.0 148.50 1280 2448 2492 2640 1024 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1440x900"x50.0 148.50 1440 2448 2492 2640 900 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1440x900"x60.0 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x960"x50.0 148.50 1280 2448 2492 2640 960 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x800"x50.0 148.50 1280 2448 2492 2640 800 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x800"x60.0 83.50 1280 1352 1480 1680 800 803 809 831 -hsync +vsync (49.7 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x768"x50.0 148.50 1280 2448 2492 2640 768 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x768"x60.0 83.50 1280 1352 1480 1680 768 803 809 831 -hsync +vsync (49.7 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x720"x60.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x720"x50.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "1024x768"x50.0 148.50 1024 2448 2492 2640 768 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 2.579] (II) fglrx(0): Modeline "1152x648"x50.0 74.25 1152 1592 1632 1980 648 653 658 750 +hsync +vsync (37.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "800x600"x50.0 148.50 800 2448 2492 2640 600 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "800x600"x60.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 2.579] (II) fglrx(0): Modeline "800x600"x56.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "720x576"x60.0 148.50 720 2008 2052 2200 576 1084 1089 1125 +hsync +vsync (67.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "720x576"x50.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "720x480"x50.0 148.50 720 2448 2492 2640 480 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "720x480"x59.9 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "640x480"x50.0 148.50 640 2448 2492 2640 480 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "640x480"x60.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 2.579] (II) fglrx(0): EDID for output CRT1
[ 2.579] (II) fglrx(0): Output DFP1 disconnected
[ 2.579] (II) fglrx(0): Output DFP2 disconnected
[ 2.579] (II) fglrx(0): Output DFP3 disconnected
[ 2.579] (II) fglrx(0): Output DFP4 disconnected
[ 2.579] (II) fglrx(0): Output DFP5 disconnected
[ 2.579] (II) fglrx(0): Output DFP6 disconnected
[ 2.579] (II) fglrx(0): Output DFP7 disconnected
[ 2.579] (II) fglrx(0): Output DFP8 disconnected
[ 2.579] (II) fglrx(0): Output DFP9 disconnected
[ 2.579] (II) fglrx(0): Output DFP10 connected
[ 2.579] (II) fglrx(0): Output CRT1 disconnected
[ 2.579] (II) fglrx(0): Using exact sizes for initial modes
[ 2.579] (II) fglrx(0): Output DFP10 using initial mode 1920x1080
[ 2.579] (II) fglrx(0): DPI set to (96, 96)
[ 2.579] (II) fglrx(0): Eyefinity capable adapter detected.
[ 2.579] (II) fglrx(0): Adapter AMD Radeon HD 7800 Series has 6 configurable heads and 1 displays connected.
[ 2.579] (==) fglrx(0): PseudoColor visuals disabled
[ 2.579] (II) Loading sub module "ramdac"
[ 2.579] (II) LoadModule: "ramdac"
[ 2.579] (II) Module "ramdac" already built-in
[ 2.579] (==) fglrx(0): NoDRI = NO
[ 2.579] (==) fglrx(0): Capabilities: 0x00000000
[ 2.579] (==) fglrx(0): CapabilitiesEx: 0x00000000
[ 2.579] (==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
[ 2.579] (==) fglrx(0): UseFastTLS=0
[ 2.579] (II) fglrx(0): Desktop Vsync is enabled.
[ 2.579] (--) Depth 24 pixmap format is 32 bpp
[ 2.579] (II) Loading extension ATIFGLRXDRI
[ 2.579] (II) fglrx(0): doing swlDriScreenInit
[ 2.579] (II) fglrx(0): swlDriScreenInit for fglrx driver
[ 2.579] ukiDynamicMajor: found major device number 251
[ 2.579] ukiDynamicMajor: found major device number 251
[ 2.579] ukiDynamicMajor: found major device number 251
[ 2.579] ukiOpenByBusid: Searching for BusID PCI:6:0:0
[ 2.579] ukiOpenDevice: node name is /dev/ati/card0
[ 2.579] ukiOpenDevice: open result is 12, (OK)
[ 2.579] ukiOpenByBusid: ukiOpenMinor returns 12
[ 2.579] ukiOpenByBusid: ukiGetBusid reports PCI:6:0:0
[ 2.579] (II) fglrx(0): [uki] DRM interface version 1.0
[ 2.579] (II) fglrx(0): [uki] created "fglrx" driver at busid "PCI:6:0:0"
[ 2.579] (II) fglrx(0): [uki] added 8192 byte SAREA at 0x2000
[ 2.579] (II) fglrx(0): [uki] mapped SAREA 0x2000 to 0x7f1426d74000
[ 2.579] (II) fglrx(0): [uki] framebuffer handle = 0x3000
[ 2.579] (II) fglrx(0): [uki] added 1 reserved context for kernel
[ 2.579] (II) fglrx(0): swlDriScreenInit done
[ 2.579] (II) fglrx(0): Kernel Module Version Information:
[ 2.579] (II) fglrx(0): Name: fglrx
[ 2.579] (II) fglrx(0): Version: 8.98.2
[ 2.579] (II) fglrx(0): Date: Jul 27 2012
[ 2.579] (II) fglrx(0): Desc: AMD FireGL DRM kernel module
[ 2.579] (II) fglrx(0): Kernel Module version matches driver.
[ 2.579] (II) fglrx(0): Kernel Module Build Time Information:
[ 2.579] (II) fglrx(0): Build-Kernel UTS_RELEASE: 3.5.3-1-ARCH
[ 2.579] (II) fglrx(0): Build-Kernel MODVERSIONS: no
[ 2.579] (II) fglrx(0): Build-Kernel __SMP__: no
[ 2.579] (II) fglrx(0): Build-Kernel PAGE_SIZE: 0x1000
[ 2.579] (II) fglrx(0): [uki] register handle = 0x00004000
[ 2.589] (II) fglrx(0): DRI initialization successfull
[ 2.590] (II) fglrx(0): FBADPhys: 0xf400000000 FBMappedSize: 0x010e0000
[ 2.591] (==) fglrx(0): Backing store disabled
[ 2.591] (II) Loading extension FGLRXEXTENSION
[ 2.591] (**) fglrx(0): DPMS enabled
[ 2.591] (II) fglrx(0): Initialized in-driver Xinerama extension
[ 2.591] (**) fglrx(0): Textured Video is enabled.
[ 2.591] (II) LoadModule: "glesx"
[ 2.591] (II) Loading /usr/lib/xorg/modules/glesx.so
[ 2.601] (II) Module glesx: vendor="X.Org Foundation"
[ 2.601] compiled for 1.4.99.906, module version = 1.0.0
[ 2.601] (II) Loading extension GLESX
[ 2.601] (II) fglrx(0): GLESX enableFlags = 592
[ 2.602] (II) fglrx(0): GLESX is enabled
[ 2.602] (II) LoadModule: "amdxmm"
[ 2.602] (II) Loading /usr/lib/xorg/modules/amdxmm.so
[ 2.603] (II) Module amdxmm: vendor="X.Org Foundation"
[ 2.603] compiled for 1.4.99.906, module version = 2.0.0
[ 2.615] (II) Loading extension AMDXVOPL
[ 2.615] (II) Loading extension AMDXVBA
[ 2.617] (II) fglrx(0): UVD feature is enabled(II) fglrx(0):
[ 2.618] (II) fglrx(0): Enable composite support successfully
[ 2.618] (WW) fglrx(0): Option "VendorName" is not used
[ 2.618] (WW) fglrx(0): Option "ModelName" is not used
[ 2.618] (II) fglrx(0): X context handle = 0x1
[ 2.618] (II) fglrx(0): [DRI] installation complete
[ 2.618] (==) fglrx(0): Silken mouse enabled
[ 2.618] (==) fglrx(0): Using HW cursor of display infrastructure!
[ 2.618] (II) fglrx(0): Disabling in-server RandR and enabling in-driver RandR 1.2.
[ 2.735] (II) fglrx(0): Framebuffer compression enabled: mcAddr=0xf407a40000 width=0xa00 height=0x3267
[ 2.735] (--) RandR disabled
[ 2.735] (II) Initializing built-in extension Generic Event Extension
[ 2.735] (II) Initializing built-in extension SHAPE
[ 2.735] (II) Initializing built-in extension MIT-SHM
[ 2.735] (II) Initializing built-in extension XInputExtension
[ 2.735] (II) Initializing built-in extension XTEST
[ 2.735] (II) Initializing built-in extension BIG-REQUESTS
[ 2.735] (II) Initializing built-in extension SYNC
[ 2.735] (II) Initializing built-in extension XKEYBOARD
[ 2.735] (II) Initializing built-in extension XC-MISC
[ 2.735] (II) Initializing built-in extension SECURITY
[ 2.735] (II) Initializing built-in extension XINERAMA
[ 2.735] (II) Initializing built-in extension XFIXES
[ 2.735] (II) Initializing built-in extension RENDER
[ 2.735] (II) Initializing built-in extension RANDR
[ 2.735] (II) Initializing built-in extension COMPOSITE
[ 2.735] (II) Initializing built-in extension DAMAGE
[ 2.736] ukiDynamicMajor: found major device number 251
[ 2.736] ukiDynamicMajor: found major device number 251
[ 2.736] ukiOpenByBusid: Searching for BusID PCI:6:0:0
[ 2.736] ukiOpenDevice: node name is /dev/ati/card0
[ 2.736] ukiOpenDevice: open result is 13, (OK)
[ 2.736] ukiOpenByBusid: ukiOpenMinor returns 13
[ 2.736] ukiOpenByBusid: ukiGetBusid reports PCI:6:0:0
[ 2.842] (II) AIGLX: Loaded and initialized OpenGL driver(II) GLX: Initialized DRI GL provider for screen 0
[ 2.857] (II) fglrx(0): Enable the clock gating!
[ 2.872] (II) fglrx(0): Desktop Vsync is enabled.
[ 2.872] (II) fglrx(0): Setting screen physical size to 508 x 285
[ 2.901] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 2.901] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 2.901] (II) LoadModule: "evdev"
[ 2.901] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2.902] (II) Module evdev: vendor="X.Org Foundation"
[ 2.902] compiled for 1.12.3.901, module version = 2.7.3
[ 2.902] Module class: X.Org XInput Driver
[ 2.902] ABI class: X.Org XInput driver, version 16.0
[ 2.902] (II) Using input driver 'evdev' for 'Power Button'
[ 2.902] (**) Power Button: always reports core events
[ 2.902] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 2.902] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 2.902] (--) evdev: Power Button: Found keys
[ 2.902] (II) evdev: Power Button: Configuring as keyboard
[ 2.902] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[ 2.902] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 2.902] (**) Option "xkb_rules" "evdev"
[ 2.902] (**) Option "xkb_model" "evdev"
[ 2.902] (**) Option "xkb_layout" "us"
[ 2.902] (**) Option "xkb_variant" "dvp"
[ 2.913] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 2.913] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 2.913] (II) Using input driver 'evdev' for 'Power Button'
[ 2.913] (**) Power Button: always reports core events
[ 2.913] (**) evdev: Power Button: Device: "/dev/input/event1"
[ 2.913] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 2.913] (--) evdev: Power Button: Found keys
[ 2.913] (II) evdev: Power Button: Configuring as keyboard
[ 2.913] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1/event1"
[ 2.913] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 2.913] (**) Option "xkb_rules" "evdev"
[ 2.913] (**) Option "xkb_model" "evdev"
[ 2.913] (**) Option "xkb_layout" "us"
[ 2.913] (**) Option "xkb_variant" "dvp"
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=11 (/dev/input/event14)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=10 (/dev/input/event15)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=9 (/dev/input/event16)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=8 (/dev/input/event17)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=7 (/dev/input/event18)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=3 (/dev/input/event19)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out Surround (/dev/input/event10)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out Front (/dev/input/event11)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line (/dev/input/event4)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Rear Mic (/dev/input/event5)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Front Mic (/dev/input/event6)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event7)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out Side (/dev/input/event8)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out CLFE (/dev/input/event9)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event12)
[ 2.914] (**) Logitech USB Receiver: Applying InputClass "evdev pointer catchall"
[ 2.914] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
[ 2.914] (**) Logitech USB Receiver: always reports core events
[ 2.914] (**) evdev: Logitech USB Receiver: Device: "/dev/input/event12"
[ 2.914] (--) evdev: Logitech USB Receiver: Vendor 0x46d Product 0xc52f
[ 2.914] (--) evdev: Logitech USB Receiver: Found 20 mouse buttons
[ 2.914] (--) evdev: Logitech USB Receiver: Found scroll wheel(s)
[ 2.914] (--) evdev: Logitech USB Receiver: Found relative axes
[ 2.914] (--) evdev: Logitech USB Receiver: Found x and y relative axes
[ 2.914] (II) evdev: Logitech USB Receiver: Configuring as mouse
[ 2.914] (II) evdev: Logitech USB Receiver: Adding scrollwheel support
[ 2.914] (**) evdev: Logitech USB Receiver: YAxisMapping: buttons 4 and 5
[ 2.914] (**) evdev: Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 2.914] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.7/4-1.7:1.0/input/input12/event12"
[ 2.914] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: MOUSE, id 8)
[ 2.914] (II) evdev: Logitech USB Receiver: initialized for relative axes.
[ 2.915] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration profile 0
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[ 2.915] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/mouse0)
[ 2.915] (II) No input driver specified, ignoring this device.
[ 2.915] (II) This device may have been added with another device file.
[ 2.915] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event13)
[ 2.915] (**) Logitech USB Receiver: Applying InputClass "evdev keyboard catchall"
[ 2.915] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
[ 2.915] (**) Logitech USB Receiver: always reports core events
[ 2.915] (**) evdev: Logitech USB Receiver: Device: "/dev/input/event13"
[ 2.915] (--) evdev: Logitech USB Receiver: Vendor 0x46d Product 0xc52f
[ 2.915] (--) evdev: Logitech USB Receiver: Found 1 mouse buttons
[ 2.915] (--) evdev: Logitech USB Receiver: Found scroll wheel(s)
[ 2.915] (--) evdev: Logitech USB Receiver: Found relative axes
[ 2.915] (II) evdev: Logitech USB Receiver: Forcing relative x/y axes to exist.
[ 2.915] (--) evdev: Logitech USB Receiver: Found absolute axes
[ 2.915] (II) evdev: Logitech USB Receiver: Forcing absolute x/y axes to exist.
[ 2.915] (--) evdev: Logitech USB Receiver: Found keys
[ 2.915] (II) evdev: Logitech USB Receiver: Configuring as mouse
[ 2.915] (II) evdev: Logitech USB Receiver: Configuring as keyboard
[ 2.915] (II) evdev: Logitech USB Receiver: Adding scrollwheel support
[ 2.915] (**) evdev: Logitech USB Receiver: YAxisMapping: buttons 4 and 5
[ 2.915] (**) evdev: Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 2.915] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.7/4-1.7:1.1/input/input13/event13"
[ 2.915] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: KEYBOARD, id 9)
[ 2.915] (**) Option "xkb_rules" "evdev"
[ 2.915] (**) Option "xkb_model" "evdev"
[ 2.915] (**) Option "xkb_layout" "us"
[ 2.915] (**) Option "xkb_variant" "dvp"
[ 2.915] (II) evdev: Logitech USB Receiver: initialized for relative axes.
[ 2.915] (WW) evdev: Logitech USB Receiver: ignoring absolute axes.
[ 2.915] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration profile 0
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[ 2.915] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 2.915] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 2.915] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 2.915] (**) AT Translated Set 2 keyboard: always reports core events
[ 2.915] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 2.915] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 2.915] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 2.915] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 2.915] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 2.915] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 10)
[ 2.915] (**) Option "xkb_rules" "evdev"
[ 2.915] (**) Option "xkb_model" "evdev"
[ 2.915] (**) Option "xkb_layout" "us"
[ 2.915] (**) Option "xkb_variant" "dvp"
[ 2.915] (II) config/udev: Adding input device PC Speaker (/dev/input/event3)
[ 2.915] (II) No input driver specified, ignoring this device.
[ 2.915] (II) This device may have been added with another device file.
[ 2.917] (II) fglrx(0): Restoring Recent Mode via PCS is not supported in RANDR 1.2 capable environments
[ 7.513] (II) fglrx(0): EDID vendor "SAM", prod id 1316
[ 7.513] (II) fglrx(0): Using EDID range info for horizontal sync
[ 7.513] (II) fglrx(0): Using EDID range info for vertical refresh
[ 7.513] (II) fglrx(0): Printing DDC gathered Modelines:
[ 7.513] (II) fglrx(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 7.513] (II) fglrx(0): Modeline "1920x1080"x0.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x720"x0.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz e)
[ 7.513] (II) fglrx(0): Modeline "720x576"x0.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz e)
[ 7.513] (II) fglrx(0): Modeline "720x480"x0.0 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 7.513] (II) fglrx(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 7.513] (II) fglrx(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 7.513] (II) fglrx(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x800"x0.0 71.00 1280 1328 1360 1440 800 803 809 823 +hsync -vsync (49.3 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)
[ 10.738] (II) fglrx(0): EDID vendor "SAM", prod id 1316
[ 10.738] (II) fglrx(0): Using hsync ranges from config file
[ 10.738] (II) fglrx(0): Using vrefresh ranges from config file
[ 10.738] (II) fglrx(0): Printing DDC gathered Modelines:
[ 10.738] (II) fglrx(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 10.738] (II) fglrx(0): Modeline "1920x1080"x0.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x720"x0.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz e)
[ 10.738] (II) fglrx(0): Modeline "720x576"x0.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz e)
[ 10.738] (II) fglrx(0): Modeline "720x480"x0.0 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 10.738] (II) fglrx(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 10.738] (II) fglrx(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 10.738] (II) fglrx(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x800"x0.0 71.00 1280 1328 1360 1440 800 803 809 823 +hsync -vsync (49.3 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)
Here's the Xorg.conf:
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection
Section "Module"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
BusID "PCI:6:0:0"
Option "OpenGLOverlay" "0"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
Monitor "aticonfig-Monitor[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
Setting the PCI BusID in Xorg.conf seems to have no effect, even if I set it to 6:0:0 or 7:0:0, its still the same.
Do I need to set AutoAddDevices off?MisterAnderson wrote:Does the same happen with the opensource radeon drivers? (xf86-video-ati)
Thanks for the reply!
The open source driver doesn't support my card yet. I tried installing it first since its the recommended driver, but Xorg couldn't detect any display at all.
It seems the PCI BusID is not being read from the xorg.conf file. There's auto detection everytime the PC boots.
Last edited by hdhiman (2012-10-04 00:43:52) -
Sound Blaster Live 24-bit PCI Sound Card and Creative Sound Blaster PCI Card not detect
Ok here is my problem. I bought a Creative Sound Blaster PCI sound card a while back and it was working fine but recently when I would boot up my computer and try to play music say off of Winamp it says Bad DirectSound Driver. When I check device manager it shows no sound card there and in sounds and audio devices it says no audio device. Now my brother believed this to be a card fault so we went to Frys and bought a Sound Blaster Li've 24-bit PCI card. I uninstalled the old drivers and installed this new one but yet it's the same problem. My assumption was that Windows XP had something conflicting so I reinstalled the OS. It found the card and I installed the latest drivers?off of this site but now it does the same thing yet again with a fresh install of Windows XP. The card has been in all 3 of my PCI slots and it will detect it for a moment but then acts like as if the card was never installed. Like I never installed a sound card into the computer. The onboard audio has been disabled for a while now but I do not know what the problem could be. I did Scan for hardware changes but it doesn't show up. Sometimes when the card is detected if I do scan for hardware changes and the card is there it will just magically disappear from the device manager as if it was never there. Even when I try to load music and I see the card is detected it will not play the music and ends up locking up Winamp to the point that sometimes will go BSOD. Now I would really like to find out what the issue is because I am planning this weekend to swap out my motherboard with a duplicate board to see if that will end up fixing the problem but I want to find out if there is any other way to fix this issue. Thank you.Message Edited by AuXoIs on 02-25-200808:28 PM
Hmm what other options is there for the bios on PCI slots?Also anything you connect to the motherboard can have oxidization (I think its that) build up on the connection. Check the connector on the card and get a eraser (Pen eraser is better) and give it a good cleaning. The connector might have alot of build-up on it and you can see it by a dark yellowy colour. I cleaned my graphics card and ram connectors after they got alot of the build-up on them. On a older computer my graphics stopped working and this fixed it. Also I went away for a while (like a month) and came back to see that my puter didn't display anything. Opened it up and saw that the graphic card had alot of corrosion? on the card connector and in the slot. Does that if you computer is turned of for a long time. Had a heck of time trying to clean the slot out. One other thing that it could be is the sound card is faulty. I had an audigy 2 and it died a while back . It picks it up and then try and use it computer freezes and the after restart it's not there anymore. Hope it's not that problem. Hope this gives you something to go by.
Maybe you are looking for
-
Push notifications not working in ios 7 on iphone 5
Since upgrading to ios 7 on my iphone 5 push notifications are not working, specifically for mail, mailbox, whatsapp and messages. I have checked all settings multiple times, hard reset and restored from back up a number of times with no results. I s
-
TS4002 How can I get a notification sound when an email arrives?
I am using Safari and icloud to manage and check emial. I am not receiving a notification sound. How can I get an audiable sound to alret me?
-
Ihave itune on my laptop and I want to put it on my ipad. The username on my ipad is not the same as mine. Can i use the same adress as the one on my laptop
-
T.code for GL Open Items clearing
Hi all,, Can anyone give the the tcode for clearing the Open items of a GL which is maintained in OIM...!? BR..AJ
-
How to Publish an eBook in PDF Format
Start a New PDF eBook Project From the Create > Create eBooks page click Make Your eBook. Alternatively, go to My Projects > Start a Project > eBook Enter a title, author name and select your project's availability. Click the Save & Continue button.