T1500 + Quadro FX 580 = Won't boot?

As above, I *think* so. It was updated recently for a different reason but I will re-check when next have phys access to machine. Thanks.
Assuming the BIOS is up to date, what else can this be? Has anyone seen anything similar? Could it be a bad card?
Thanks

Hey all,Have a user w/ a T1500 that originally came with an nVidia quadro FX 380 vid card. Wanted to upgrade user to dual 28" monitors and this required DisplayPort. So a quadro FX 580 looked good and works but only partially:System works and runs normally with one monitor connected to DVISystem work and runs normally with one mon on DVI and another on DPSystems *fails to POST* with no monitors on DVI. One or two monitors (daisy-chain) on DP, no diff. Seems to me it doesn't even enter POST. I get blue power button light, gentle response from fan(s), not much else.Same port, monitor and cable that won't boot, works well once in Windows (W7 64) but only if at least one mon is DVI.So? What gives? Any thoughts on what to do next? Kinda head scratching. Drivers are the lates from nVidia btw and *I THINK* the machine bios is latest but...
This topic first appeared in the Spiceworks Community

Similar Messages

Mac LC 580 won't boot

My Mac LC 580 won't boot. I have tried the following in a attempt to get it to work:
Reset the logic board. Replaced the hard drive. Cleaned the logic board's end connector with contact cleaner. Cleaned the RAM modules with contact cleaner. The only thing I know for sure is that Apple's service manual for the LC 580 keeps pointing towards a bad logic board or analog board or both as the cause of death. I'm not even getting a bong from the Mac. The only thing I hear when I turn it on is the sound of the Mac running. Maybe the hard drive too. No video appears on screen either. The original hard drive was a Apple OEM Connor 800 MB OEM drive. Personally I've heard far too many horror stories about Connor hard drives from the PC world online to trust it as being reliable. It even said right on the drive that it was made in Malaysia of all places. Not a good sign if you ask me. I have managed to locate a replacement logic board on eBay if that turns out to be the cause of the Mac's death. What's the next step in getting this old Mac up & running?

Update: I have more info on what's been going on with the LC 580. I finally figured out that the 33MHz Motorola 68040 processor I installed may be defective. After switching the the original Motorola 33MHz 68LC040 & removing the RAM the Mac booted but I got a Quizzical Floppy on screen indicating the Mac couldn't find a valid System Folder. After that I figured out that the Apple SCSI 4X CD-ROM drive was defective. I replaced it with a known good Apple 8X SCSI CD-ROM drive. I then attempted to boot from a Mac OS 7.6.1 CD-ROM. I got a error type 41 & restarted with extensions off like the error told me to. I then attempted to boot from a Mac OS 8.1 CD-ROM but I got a Sad Mac error code. The error code looked like this:
0000000F
00000001. Just now I tried to boot from the Mac OS 7.6.1 CD-ROM. Again I got a error type 41. After that I booted with extensions off from the Mac OS 7.6.1 CD-ROM. I still got a error type 41 too. I then restarted & got the following Sad Mac error code:
0000000F
00000033. I also have a Mac OS 8.0 CD-ROM that I haven't tried to boot from yet. What does all of this mean & what should my next move be?

Quad PPC won't boot--near wit's end

I have a fun little mystery on my hands. At work, we have a Quad-Core PPC (I don't remember which flavor it is, but it's about 2 years old or so now, I believe) which stopped booting up. Here's the skinny: I sat down to the computer (which is barely used anymore, btw, since our graphics guy left last summer) to launch iTunes, and it kept unexpectedly quitting. Launched After Effects 7, unexpectedly quit. So, I figured I'd restart.
After restart, I got the grey screen w/Apple logo & the spinning gear. After maybe 30 seconds, the fans kicked into high gear (though not quite as high as when you go into Single User Mode on this box). That's been the running symptom throughout my repair attempts. Here's what I did to try and recover:
DiskWarrior - wouldn't replace the directory the first two times due to overlapped files. After running FSCK 3 times, DiskWarrior (supposedly) replaced the directory. However, running a 4th time yielded .rsrc & .plist files which could not be repaired (most of which were DVD Studio Pro & After Effects 7 related, but there were three that were users prefs related). I went through the list and deleted the problematic files.
*Repaired permissions from the Install Disk (repaired a few things, then was ok)
*Disk Repair from Install Disk (came out ok)
*Reset PRAM
*Reset NV-RAM
*unplugged the computer for 5 minutes to let it sit w/o power
*Installed 10.4.10 (which is the OS it was running) combo update via Target Mode (after doing this, the Quad still came to the same grey screen, except the fans stopped kicking into high gear)
Used "Preferential Treatment" to look at preferences via Target Mode. Nothing found.
*Re-seated RAM (4x1GB)
*unplugged everything from the Mac except keyboard/mouse & two monitors.
I don't have a usable copy of TechTool (the AppleCare version I have won't boot on this machine for some reason). Safe boot will not work last time I tried (grey screen with hyper fans). Single User Mode still works. Booting from the install disc still works. All RAM is from Apple. Video card is an NVIDIA Quadro (not sure which flavor nor how to tell). This Mac is set to come to the log in screen, so it does not automatically go into a user account upon booting.
Though I'm not completely knowledgeable, I didn't see anything out of the ordinary in the Startup Items folder (while in Target Mode), and if this box came with a Hardware Test Disc, I can't find it.
I've already cloned over the boot drive for safety (incidentally, if you ever have interest in cloning 383GB of data to a disk image, be prepared to wait 3 or 4 hours for that disk image to verify after you've asked it to mount). I went through similar problemswith this Quad last September, though I didn't go through all these steps last time. I ended up doing the Archive and Install, which worked. Didn't know that time either what had gone wrong.
At this point, I'm about ready to zero the drive and start all over, fresh--no restoring from the back up clone. Any recommendations before I go to that step? We do have AppleCare on it, but I really don't want to go there unless it is absolutely the last thing to do (I'd rather try wiping the drive and starting over than send the thing in for "repair"). Right now, I've asked it to boot since re-seating the RAM, so I'm just going to let it spin all night and see what I find in the morning.
Also, if I wanted to try clearing the cache, is it ok to go into the cache folder and just wipe it out completely or are there certain things that must remain? If you'd like me to try clearing the cache manually, please give me the file path so I know I'm going to the right place.
Message was edited by: MyKidsDad

Hi! The directory is corrupt and the only way to resolve it it using Diskwarrior which has already failed or reinstalling. You can try an archive and install and if that fails you'll have to erase and install. DON'T use a clone because cloning an unstable system with problems rarely if ever yields one in better shape. Most likely DW wasn't used regularly and the directory corruption got worse and worse until the boot failure and hence DW inability to resolve the problem. Tom

Laptop won't boot after installing iPod Shuffle

I got a new iPod Shuffle and I installed the software from the CD provided onto my laptop (Sony VAIO running Windows 2000). Now the PC won't boot at all, not even in safe mode.
The boot starts out ok, but hangs forever with the Windows 2000 splash screen showing and the progress bar for starting up displayed.
In safe mode, the last system driver loaded was mup.exe. I followed some suggestion found on other web sites but nothing seems to help.
What has the iPod shuffle software done to my lpatop? How do I get the laptop to boot?
I can boot from a floppy. I can run the recovery from the Windows 2000 CD, but still the laptop will not boot.
Help!
Thanks
Chuck
Sony VAIO Laptop Windows 2000 PCG-FX190K - 800 MHz

As in 1st post, there is no last 'good' configuration as it is a fresh install of XP. Rolling back will just get back the default windows driver which cannot support the Nvidia NVS card. My goal is to successfully install the Lenovo Nvidia Quadro NVS 140m driver.
That said, could my problem lie with the XP version? The fresh install is XP SP0. If I update to SP3 do you think that will solve the problem (i.e. the graphics driver is written for later versions of XP)?

W520 won't boot with eSATA RAID disks attached to Mini Dock 3 Plus

Hoping there is a simple fix to this. My month-old W520 (i7 2720QM, 16GB, Intel 80GB mSATA, 500 GB Seagate installed) sits in a Mini Dock 3 Plus. There have been absolutely no problems booting in or out of the dock.
I recently installed a 2 TB RAID 1 box in the Mini Dock 3 Plus's eSATA port (Raidon 2-disk enclosure, 2x 2 TB Hitachi 5K3000.) It performs well (great speed, very reliable so far.) Everything was fine until I shut down and rebooted--then it hung at the Think screen. Removing the eSATA connection and rebooting led to a normal boot.
I can always take the W520 out of the dock to reboot, but this is a bit of a pain. Does anybody know a way to fix this?
Thanks for any pointers.

There are similar issues with WD HDDs during boot, look at http://forums.lenovo.com/t5/W-Series-ThinkPad-Laptops/W520-won-t-boot-when-docked-in-mini-dock/td-p/... Unfortunately, there is no solution at this moment. I'd like to know whether it was properly reported as an issue or at least if there is some progress in resolving it, but it seems the only thing we can do is hope it will be resolved in the next BIOS/UEFI release. By the way, do you use BIOS or UEFI? When I was using BIOS, the issue was exactly the same as you describe. Then I moved to UEFI and now it doesn't freeze on Think screen, but tries to load the OS and during that process it fails and reboots.
Lenovo ThinkPad W520 15.6" 1920x1080, UEFI 1.42, Intel Core i7-2820QM 2.3GHz, Intel HD3000 + nVidia Quadro 2000M 2GB, Kingston PNP 16GB (4x4GB) 1600MHz RAM, Crucial m4 040H 256GB SSD, Lenovo TP Drive Adapter UltraBay 12,7mm + WD Blue 1TB 5400rpm HDD, Intel Centrino Ultimate-N 6300 AGN, Gobi 3000, Lenovo TP Port Mini Dock Plus Series 3, Windows 8.1 Pro 64bit

Computer Won't Boot Up

Here is my issue, my computer one day was working fine and the next it won't boot properly.
System Specs: Satellite T235D-S1345RD (Laptop) - Windows 7 (64bit) - BIOS 1.7 - 4gb RAM -
I have gotten the computer booted one time. I am unsure why it did that time but did not do it another time.
Since that one time I put the computer in hibernate and when I tried to bring it out it told me it failed when coming out of hibernate so it went to reboot and now won't boot.
Here are the few steps I have done to try and get it working. When it boots up it gives me an error message (says that power failed or for some reason it did not boot)
I have ran "Repair Computer" and it does not do anything. I try start windows normally and it goes no where.
So I then tried F8 and got into the Advanced Boot Menu. First one I tried was Start Windows From Last Known Good Configuration. (or something like that I forget the exact wording)
When it does that the computer will start to boot up go to the "Windows Loading" screen and then it flashes a blue screen (there are words there but it flashes so quickly I cannot read it) and it goes back to the boot screen and acts like it is restarting and continues in that loop.
Next step - Enter F8 again tried "Repair Computer" and it loads to a black screen with a Cursor but nothing ever happens. I have given it over 30 min and nothing happens.
So next step- I enter F8 again and try to boot up in safe mode and again when it loads it flashes a blue screen and then nothing.
EDIT - I found how to show the blue screen. It says UNMOUNTABLE_BOOT_VOLUME. Not sure what else I should do after I get that error message. Message Reads:
It reads UNMOUNTABLE_BOOT_VOLUME and says if it's the first time I've seen the error screen, to restart the computer. Then it tells me if it appears again, to check and make sure any new hardware or software is properly installed.
"If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode."
END EDIT
Next Step: I come to you guys here on this forum. I am a bit perplexed and lost at what to do. I wonder if this is a virus but I cannot get the computer to respond to try to get into it to check.
Ideas? Advice? What should I try? I can get into the F8 menu but not sure what else I should try. I will try anything to get this computer up and running!
Thanks for any and all help.
Lynda

Hi:
The 24 character failure ID usually indicates HDD is failing/has failed. You need to replace it with a new one.
Specs: http://support.hp.com/in-en/product/HP-Pavilion-dv6-Entertainment-Notebook-PC-series/5191856/model/5...
Manual: http://h10032.www1.hp.com/ctg/Manual/c03099531
Check warranty: http://h10025.www1.hp.com/ewfrf/wc/weInput?cc=us&lc=en
Order recovery USB: http://support.hp.com/in-en/product/HP-Pavilion-dv6-6c13cl-Entertainment-Notebook-PC/5191856/model/5...
Contact HP: https://support.hp.com/in-en/contact-hp/product/HP-Pavilion-dv6-6c00-Entertainment-Notebook-PC-serie...
If you're under warranty, HP would send you replacement HDD.
If you're not, buy any branded 2.5" SATA 9.5mm thick internal laptop HDD and replace it yourself. But HDD of at least same capacity HDD as the one that came with your laptop (640gb) so that recovery media would work -
Go through page 56-58 in the Manual for replacement procedure. It's quite simple DIY job.
Something like this:
http://m.newegg.com/Product/index?itemnumber=N82E16822236561
If you've not yet created the Recovery media to restore the factory settings after replacement, you have to order a set of Recovery USB from HP.
For salvaging the data from old HDD, I suggest you take out the drive. Connect it to another PC using SATA to USB adapter - copy all the files you need.
http://www.amazon.com/Anker®-Converter-Adapter-Cable-included/dp/B005B3VO24
Regards
Visruth
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP**

Satellite m300 won't boot! please help!

Hi,
I've got a bit of an issue here.. I have a Satellite m300.. a white one..
and it won't boot... I've had this very issue before but it turned out to be an external USB HDD that stopped it from booting up but now even with everything removed it still won't boot.
And it was fine until yesterday, it just gave up.. I am away from home for work so I have all the work stuff and unfortunately without my recovery cd, but my guess is that it won't even read it..
So this is what happens..
turn on..
all light come on.. including power and all the white lights around the keypad..
and then maybe 5 sedconds later caplock and numlock(?) green lights flash..
then it's a dead still.. no HDD activities or sound.. just dead quite..
the screen remains black blank through out..
it seems to get stuck here before reaching the post screen.
i thought the power button usually took more than just a push to turn off? it instantly swithces off with a single push of the power button..
I think this laptop is like on sleep or something and can't seem to wak up.. maybe?
And it has vista.
Please help.. I have some important work files I need to recover at least before formatting..
and that has to wait till I get home which won't be for a month or so..
which also lets me take it back for warranty as well..
any help appreciated!!!
cheers,
Min

Quote
Originally posted by syar2003
If running a LCD display with DVI connection , try to hook it up with
an analog VGA cable.
Can also be that the motherboard fails to initialize the vga AGP card.
Turn off all power incl. AC .
Disconnect all devices from motherboard : AGP/memory/drives/floppy/USB/PCI cards etc. take out the 20pin & 4pin PSU connectors and reset the motherboards
cmos .
Assemble PSU connectors ,only one DIMM module and graphics card and turn it on and se if you get a post .
Just removed all components. I reset the CMOS. I then reconnected the 20pin and 4pin, 1 stick ram, and the video card (no ide devices, no mouse, keyboard cd drives) and the monitor doesn't show up. I also tried another monitor so it isn't the monitor.
Could it have a bad AGP port?
Any other suggestions? I am thouroughly stumped. Also the power and reset buttons don't work no matter what configuaration I put the front panel connectors in. The Power LED is lit up and it doesn't work and the reset light is off and it doesn't work.
Also noticed one of my fans connected to one of the two other fan pins on the motherboard isn't working.
What a nightmare.

Mid 2010 MacBook Pro won't boot past blue screen

I've been having problems booting up my MacBook. I can't get past the blue screen. It went from booting slow at the grey apple logo screen to not booting up at all. Is it a problem with my hard drive? I also have boot camp running as well, but I can still see the boot camp drive for windows and my OS X drive, as well as my installation disk when I have it inserted when I hold the option key at start up.
I'm still able to run windows on it without any problems when I pick the windows drive. I tried different methods from different forums but I'm just not getting through. I tried holding 'c' to boot up from cd and I let it run over night but it never got past the grey apple screen with the gradient wheel (still spinning). I had already used time machine to back everything up before this happened since I was able to boot up properly (but slowly). Can anyone help? It's driving me nuts, and I can't remember what os/firmware version I'm running.

n your signature you said you are running 10.6.3. So let’s assume you are running Snow Leopard.
It sounds like your diagnosis of disk problems is correct. The OS X partition may be corrupt.
Try booting in Safe Mode.
http://support.apple.com/kb/HT1564
Try again to boot in normal mode.
If it will boot in Safe Mode but not in normal mode then you could have some 3rd-party software preventing the boot or you could have a corrupt disk or OS.
Boot as from the startup manager (Boot - option) and then select the installation disk.
Hopefully that will work better than starting with the Boot-C option.
Then try to repair the system disk.
Start the Disk Utility.
Perform the steps in http://support.apple.com/kb/PH5836.
If it repairs OK but still won’t boot reinstall OS X.
Installing Mac OS X 10.6 SnowLeopard
http://kb.iu.edu/data/akav.html

MacBook Pro Retina 15" mid-2012 won't boot in clamshell mode with an external display attached

I have a 15" MBPr mid-2012 running OS X 10.10.1. The system won't boot in clamshell mode (power is connected, lid shut) with an external display attached via an Apple Thunderbolt->DVI adapter. it boots fine if the lid is open. It isn't the adapter or the display since my 15" MBPr mid-2014 boots up just fine connected to the same adapter and monitor. And this system used to boot like this just fine some while ago (probably before it was upgraded to Yosemite). I've reset the NVRAM (twice) to no avail.
Has anyone encounter this? Anyone have a solution? Should I try an SMC reset (always a bit nervous about that)? Might it be a driver issue in Yosemite?
Thanks.

I have a 15" MBPr mid-2012 running OS X 10.10.1. The system won't boot in clamshell mode (power is connected, lid shut) with an external display attached via an Apple Thunderbolt->DVI adapter. it boots fine if the lid is open. It isn't the adapter or the display since my 15" MBPr mid-2014 boots up just fine connected to the same adapter and monitor. And this system used to boot like this just fine some while ago (probably before it was upgraded to Yosemite). I've reset the NVRAM (twice) to no avail.
Has anyone encounter this? Anyone have a solution? Should I try an SMC reset (always a bit nervous about that)? Might it be a driver issue in Yosemite?
Thanks.

IMac shut down suddenly and won't boot back up

This morning my iMac shut down suddenly. All I had open was Google Chrome and I was just on Facebook and that's it. When I tried to boot it back up, it wouldn't load past the startup sound, wherein it would appear to shut back down,or at the very least the screen would go black (my mouse has lights that stay on when the computer is on, and the light kept going on and off while the screen remained black). This was the case for at least a half hour until it suddenly booted itself back up all on its own. I had it on throughout the day, just browsing the internet and watching Youtube. It shut itself down twice during the day, and both times it restarted on its own right away after showing me a grey screen with the Apple logo and a progress bar. Now it just shut itself down again and it won't make it past the progress bar screen - if it even makes it that far, sometimes it shuts off right after it makes the startup sound. It keeps trying to boot up on its own over and over again, but it keeps shutting down right away. All the fixes I've searched for so far require a computer that actually boots up all the way so I don't think I could run any reports if I tried!
I'm running the latest version of Yosemite (10.10.2?).
Model number A1311
Not entirely sure what specs are useful to know so I'm just gonna write some of what's on the box it came in:
3.2 GHz Intel i3 processor, 4MBshared level 3 cache
4GB of 1333MHz DDR SDRAM
1TB serial ATA hard drive
ATI Radeon HD 5670 graphics processor with 512 MB of GDDR3 memory
Bought it around fall of 2010. Not sure if it's worth trying to get it fixed (I live nowhere near an Apple store) or if I should just get a new computer, but I would like to know what's wrong, if possible.

Try to boot into the Recover Partition by holding down the Command + R keys on startup. If it still won't boot then the HD has probably crashed. The is likely a AASP in your area, you can locate one by clicking AASP Locator, take it to one to be professional diagnosed. If it's only the HD, assuming you have been backing up, restoring to a new HD is pretty simple.

[865PE NEO2 PFISR] Won't boot with added memory

Recently I upgraded a few items on my PC which has been running fine for 18 months or so. I changed out the video card and bought double the memory of the same brand and type it had in it. I went from 1gig (2 sticks) and added two more sticks. But now it won't boot. The power is on but no output whatsoever.
I RMA'd the memory thinking that might be the problem but it's the same with the new set. I tried all sorts of memory/slot combos. Basically, the new memory works fine if you swap it out in bank A with the old stuff. That's how it's running right now, so I know all of the sticks are good. I can take a third and put it in either slot bank B and it'll boot, but obviously not run properly. But any combination of these four sticks and the system won't boot!
Please help!
I'm running this system:
Win XP (SP1 I believe)
865PE NEO2 PFISR
P4/3.0CGHz, 800M 478P/512K HT
DDR Corsair 512MB X4 (400)
Dual 80gb samsung HDs running SATA
Sapphire X800GTO 256M video card
Antec Sonata case
TruePower 380Watt ATX12V

What brand, model, and speed are the RAM sticks. Did you check your Test Report booklet which came with the mobo. If you can't find it, you can go to the MSI website and look for your MOBO and get the test report that way. Some brands/models will that have been tested are shown in the report to be okay in all 4 slots, some only test okay in 2 or 3. Check this report and if it is one of the brands/model/speed tested you will see how it fared. It may well be you the MOBO doesn't like your RAM in 3 or 4 slots.
Maybe I missed it, but did you try each slot with only one stick at a time? You may also have a bad RAM slot.

Lenovo G560 - Issue with won't boot and black screen after HDD upgrade

Lenovo G560 - Issue with won't boot and black screen after HDD upgrade.
What happen: My laptop was working fine, no blue screen issue, no funny business at all. I bought a new SSD Intel 120 GB and thought it would be a good idea to replace the HDD. I shutdown and disconnected the power adapter, waited a couple of minutes and removed the battery. I opened up the back case and replaced the HDD. And put all the screws back and put the battery back in.
Problem: The very first time I turned the power on, nothing happens besides a black screen. I pressed the dvd drive it works and opens up and closes. I waited for about 30 mins and still has blac screen. When I mean black screen, no bios menu, no logo, just a black screen with the fan sound on.
I have tried these:
1. Unplugged everything - battery, adapter, and pressed the power on button for about 60 seconds, nothing, the laptop turns on with the LED display on for both on and battery LED's. But nothing but black screen, no sound of windows loading just the fan and black screen.
2. I tried putting back my old 2.5" and nothing but black screen.
Thoughts and suggestions?
Solved!
Go to Solution.

Hi Autoexit173,
Welcome to Lenovo Community!
As per the query we understood that you are facing issue with system not booting in your Lenovo G560 laptop.
As you have mentioned that the system not booting, please try to remove the RAM and turn on the system and check if you can hear any beep sound. Also try to clean the RAM slots and check for the issue.
Click here for the steps to remove the RAM and refer page number 40.
Hope this helps. Do post back if issue persists!
Best regards,
Ashwin.S
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

My Macbook Pro won't boot up, I don't have any discs...bought from Craigslist

I bought my Macbook Pro (2012 model) from Craigslist and only had it about a week, but this morning I couldnt boot it up. I didnt get any discs with this computer. Only the powercord. What can I do to get it to boot up and where can I go from there? There was a software update last night and this morning it won't boot up. Is my only option going to Apple Store? Is there anything else I can try to at least get it to boot up?? Thanks so much.

Yea, it has Mountain Lion on it. I have tried starting while holding down Command-R, and also the Comand R, Option P, and still won't let me boot up. I made an appointment for a Genius Bar... Is this who I make the appointment with for help with this? We checked the seriel number from "About this Mac" and we went to view that it had a few years left of apple care. It happened right after a software update. Wonder if that caused it. Is there viruses out there for Mac's and should I have a program to clean it up after I get it going or IF I get it going tonight? Thanks,
Curt

Hi guys I'm really in need of some help. I have an IMac I3 for a while now I've been having a problem of my machine refusing it shut down , it goes to a blue screen with a spinning wheel but doesn't shut down. And now won't boot from install DvD

Please some one help me ...
A) my mac won't shut down with external HD connected (if it's been used)
B) there are disk permissions that can't be fixed SUID stuff ..
C) I have now verified the Mac HD and it tells me it's corrupt in bold red writing and to start up from install DVD
D) it won't boot from DVD so I cannot run the repair , initially the machine was spitting it out on start up , now it appears to be attempting to boot off DVD , well it sounds like it is .... BUT it's hanging with the Mac Logo and a wheel ... For um .... 30min now...
E) weirdly when OSX is booted off the hard drive , it won't recognise the Install DvD or the applications one... It just spits them out....
I had an old PPC 17" and it was a beaut .... Never had a single problem with it ...
I bought this one December 2010 and it's been nothing but issues for a computer in excess of £1000 I'm extremely disappointed ... And weirdly the shutting down issue started when it was a week out of warrantee ... I feel conned and am almost at the point of throwing it at a wall and buying a PC

Ok so I've done what you said and this is what it's come back ....
I don't know that these are the errors , but they're the things which don't look right ...
Throughout the shut down there is a recurring line ;
It says ;
Com.apple.launchd 1 0x100600e70.anonymous.unmount 301 PID still valid
Then there are 2 more which I think are related ;
Com.apple.securityd 29 PID job has I overstayed its welcome , forcing removal.
Then the same with fseventd 48 and diskarbitrationd 13
Oh and on Launchd1 : System : stray anonymous job at shut down : PID 301 PPID13 PGID 13 unmount...
Then the last process says "about to call: reboot (RB_AUTOBOOT).
Continuing...
And stops ...
Hope this means something to you ... Thanks again for your help so far :-)

FileMaker Server problem on Mac Mini Server - Mac Mini won't boot

I just installed a brand new Mac Mini Server today, and also FileMaker Server 11. A first-timer for both Mac OS X Server and FileMaker Server, I made an error as explained below, and right now I don't know how to get back on track with the system. It won't boot.
So, how did this happen?
At first everything was proceeding according to plan. I configured the pre-installed Mac OS X Server on the Mac Mini with users, groups and services. This was tested from clients and this seemed to work just fine. Then I installed and configured FileMaker Server. This was also tested from a client, and the example database that came with FMS was served up just fine.
The problem arose when I tried to install my existing FileMaker databases. I simply checked to see where in the file system the example database was located, and then copied my old databases to that location (I think it was Library > FileMaker Server > Data > Databases or something close to it - can't check it now...). I had the FileMaker Server Admin Console running, and hit the Refresh button hoping that this would make FileMaker Server find the databases.
This was my first error. I should have read ahead in the instructions to see that one is supposed to use an Upload Database assistant instead...
What happened when I hit refresh was that the FileMaker Server Admin Console became completely unresponsive with a spinning ball as cursor. I left it for about an hour hoping it would terminate, but gave up and tried to shut it down. It wouldn't close, so I force quit it from the Finder. Then I tried to shut down FileMaker Server, but I needed to force quit this as well. After this I thought it would be best to reboot the Mac Mini, so I shut it down, but now it won't even boot, it just stays on the screen with the spinning wheel for ever!
I have tried all the keyboard options while booting, but nothing seems to help. In safe mode, the grey progress bar just grows to about one third, then disappears and leaves the eternally spinning wheel.
The server version of the Mac Mini doesn't have an optical drive, only two internal hard drives. I tried to reinstall from scratch using the optical drive on another Mac on the network. The startup disk appeared when I tried to boot the Mac Mini holding down the option key, and after about 20 minutes or so of the spinning wheel I could actually access the discs. I started by running Disk Utility to check disk permissions. There were a lot of repairs concerning permissions and groups, especially on "Library". It said "ACL differs on Library", I don't know what this is but this was repaired. I then ran Repair Disk. The volume appeared to be OK.
When I tried to reinstall Mac OS X Server however, this failed with the message
"You can't upgrade this version of Mac OS X because a newer version is installed. Mac OS X Server couldn't be installed on this disk." I don't know how this can be, but I may have run software update earlier today.
What should I try next? Should I erase the primary HD and try to install again? Or should I install the system software on the secondary HD? Or should I just try to reboot as is in the hope that the disk permission repairs did the trick...?
Any helpful pointers would be greatly appreciated!

Hello there, I came across your post when browsing the forum for passive advice. I am in the same boat as you and am a first timer for both of these tools. I work for a company who now needs to expand its network and database capabilities. I have been assigned this task and these are the tools i have opted for. I have not yet purchased them and i am pleased to find someone who has my desired setup. Could you please advise on the simplicity of the setup and whether an advanced knowledge is required.
I want to use it in a mixed operating system environment. Is this possible?
Regards
Matthew

T1500 + Quadro FX 580 = Won't boot?

Similar Messages

Maybe you are looking for