T3 Oracle´s proprietary tunneling protocol and Cisco ACE
Does anybody know if it is possible to load balance the T3 Oracle´s proprietary tunneling protocol supported by Oracle Weblogic with Cisco ACE?
TIA,
Claudio Uemura
HI Claudio,
I don't know much about T3 protocol, in short you can load balance almost anything really, the issue becomes to how granular and if you can do any intelligent inspection besides source and dest ip and if there are multiple different connections on different ports. These last points sort of decide whether it's worth it.
- If you find the specifics about the connection ( port, type of protocol and type of connection ( long-lived or short lived) you should be able to setup a basic rule to test. A sniffer trace will give you the most information if oracle website does not explain T3 in detail.
- From a quick search there also looks to be a method to encapsulate T3 inside a http packet on weblogic servers, if this were the case then you could do some deep packet inspection with regex etc to get more granular load balancing
http://forums.oracle.com/forums/thread.jspa?threadID=706909
I would think it's defintely worth looking at both options
cheers,
Chris
Similar Messages
-
TACACS and Cisco ACE Load Balancers authentication ?
Is there a need to have user accounts locally on the Cisco ACE Load Balancers as well as the User accounts on TACACS where it is being authenticated ?
Many thanks
FlorrieYes.
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA3_1_0/configuration/security/guide/aaa.html#wpmkr1517596 -
Site-to-Site VPN between Cisco ASA 5505 (8.4) and Cisco Router (IOS 15.2)
Hi, I'm trying to create Site-to-Site VPN between Cisco ASA 5505 and Cisco Router 3945.
I've tried create configuration with and without ASA wizard, but anyway it doesn't work.
Please help me to find where is the issue.
I have two sites and would like to get access from 192.168.83.0 to 192.168.17.0
192.168.17.0 --- S1.S1.S1.S1 (IOS Router) ==================== S2.S2.S2.S2 (ASA 5505) --- 192.168.83.0
Here is my current configuration.
Thanks for your help.
IOS Configuration
version 15.2
crypto isakmp policy 1
encr aes 256
authentication pre-share
group 2
crypto isakmp key cisco address 198.0.183.225
crypto isakmp invalid-spi-recovery
crypto ipsec transform-set AES-SET esp-aes esp-sha-hmac
mode transport
crypto map static-map 1 ipsec-isakmp
set peer S2.S2.S2.S2
set transform-set AES-SET
set pfs group2
match address 100
interface GigabitEthernet0/0
ip address S1.S1.S1.S1 255.255.255.240
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map static-map
interface GigabitEthernet0/1
ip address 192.168.17.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
access-list 100 permit ip 192.168.17.0 0.0.0.255 192.168.83.0 0.0.0.255
ASA Configuration
ASA Version 8.4(3)
interface Ethernet0/0
switchport access vlan 2
interface Vlan1
nameif inside
security-level 100
ip address 192.168.83.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address S2.S2.S2.S2 255.255.255.248
ftp mode passive
same-security-traffic permit intra-interface
object network inside-network
subnet 192.168.83.0 255.255.255.0
object network datacenter
host S1.S1.S1.S1
object network datacenter-network
subnet 192.168.17.0 255.255.255.0
object network NETWORK_OBJ_192.168.83.0_24
subnet 192.168.83.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any log
access-list outside_cryptomap extended permit ip 192.168.83.0 255.255.255.0 object datacenter-network
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn_pool 192.168.83.200-192.168.83.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic inside-network interface
nat (inside,outside) source static inside-network inside-network destination static inside-network inside-network no-proxy-arp route-lookup
nat (inside,outside) source static inside-network inside-network destination static datacenter-network datacenter-network no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.83.0_24 NETWORK_OBJ_192.168.83.0_24 destination static datacenter-network pdatacenter-network no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 DEFAULT_GATEWAY 1
crypto ipsec ikev1 transform-set vpn-transform-set esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set vpn-transform-set mode transport
crypto ipsec ikev1 transform-set L2L_SET esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set L2L_SET mode transport
crypto dynamic-map dyno 10 set ikev1 transform-set vpn-transform-set
crypto map vpn 1 match address outside_cryptomap
crypto map vpn 1 set pfs
crypto map vpn 1 set peer S1.S1.S1.S1
crypto map vpn 1 set ikev1 transform-set L2L_SET
crypto map vpn 20 ipsec-isakmp dynamic dyno
crypto map vpn interface outside
crypto isakmp nat-traversal 3600
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
group-policy GroupPolicy_S1.S1.S1.S1 internal
group-policy GroupPolicy_S1.S1.S1.S1 attributes
vpn-tunnel-protocol ikev1
group-policy remote_vpn_policy internal
group-policy remote_vpn_policy attributes
vpn-tunnel-protocol ikev1 l2tp-ipsec
username artem password 8xs7XK3To4s5WfTvtKAutA== nt-encrypted
username admin password rqiFSVJFung3fvFZ encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool vpn_pool
default-group-policy remote_vpn_policy
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group S1.S1.S1.S1 type ipsec-l2l
tunnel-group S1.S1.S1.S1 general-attributes
default-group-policy GroupPolicy_S1.S1.S1.S1
tunnel-group S1.S1.S1.S1 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f55f10c19a0848edd2466d08744556eb
: endThanks for helping me again. I really appreciate.
I don't hve any NAT-exemptions in Cisco IOS Router. Transform-set I will change soon, but I've tried with tunnel mode and it didn't work.
Maybe NAT-exemptions is the issue. Can you advice me which exemptions should be in Cisco IOS Router?
Because on Cisco ASA I guess I have everything.
Here is show crypto session detail
router(config)#do show crypto session detail
Crypto session current status
Code: C - IKE Configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
X - IKE Extended Authentication, F - IKE Fragmentation
Interface: GigabitEthernet0/0
Session status: DOWN
Peer: 198.0.183.225 port 500 fvrf: (none) ivrf: (none)
Desc: (none)
Phase1_id: (none)
IPSEC FLOW: permit ip 192.168.17.0/255.255.255.0 192.168.83.0/255.255.255.0
Active SAs: 0, origin: crypto map
Inbound: #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0
Should I see something in crypto isakmp sa?
pp-border#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id status
IPv6 Crypto ISAKMP SA
Thanks again for your help. -
Site to Site VPN between ASA 5505 and Cisco 800 router
Evening all,
Hoping that someboy can see the error of my ways. It seems very like the problem that i read here: https://supportforums.cisco.com/thread/2016300
We have a cisco 800 in a remote site which we wanted to use for a site to site vpn. Went through the steps on the ASA 5505 and the 800 and have got to the stage were the tunnel is up and connected. Getting traffic through it is another matter. Remote network is 172.20.224.0/20 and the server network behind the ASA is 192.168.168.0/24. The tunnel does intiate when you send traffic from 172 ......to 192....... Both the ASA and 800 report the tunnel is up. If i look at the stats using ccp on the 800 i can see the encapsulation packets graph shooting up but nothing cominbg back. I did packet captures on the 5505 and could not see anything coming from the tunnel so i dont belive its making it to the ASA. Here is the config from the 800:
Building configuration...
Current configuration : 6488 bytes
version 12.4
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname hhp-sty-backup
boot-start-marker
boot-end-marker
logging message-counter syslog
logging buffered 4096
enable secret 5 $1$jI1i$/kZbRk2WHD5h0HtfuQVej1
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa authorization auth-proxy default local
aaa session-id common
crypto pki trustpoint TP-self-signed-1347488939
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1347488939
revocation-check none
rsakeypair TP-self-signed-1347488939
crypto pki certificate chain TP-self-signed-1347488939
certificate self-signed 02
30820255 308201BE A0030201 02020102 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31333437 34383839 3339301E 170D3032 30333031 30313336
33375A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 33343734
38383933 3930819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100E714 7B0ADB41 19F60528 A8A5C43B 5CD2D1CD DCCF2E08 8B38D444 36EAB9B7
0E93CEF7 660F979E E27915B9 E44812A5 794EA03D BA66752B FD0F7EBF D6342513
D6410E4E 098CE838 C3BADD0A 5F3505FE 22CA776F 89B19510 F0852225 3600F046
4D57D2E2 FE4AAD1E 8BE4BF80 7B27369E BFA65160 BC769BC9 00A13741 E336D0EA
8A810203 010001A3 7D307B30 0F060355 1D130101 FF040530 030101FF 30280603
551D1104 21301F82 1D686870 2D737479 2D626163 6B75702E 796F7572 646F6D61
696E2E63 6F6D301F 0603551D 23041830 168014FA 4A8C4DF6 629638DE 87D7B60A
0F5BB40F EA6AED30 1D060355 1D0E0416 0414FA4A 8C4DF662 9638DE87 D7B60A0F
5BB40FEA 6AED300D 06092A86 4886F70D 01010405 00038181 00BBE577 6EF63FE7
789766D5 37841812 298D4885 1CD06D07 4C625369 C3403106 89EE1398 73495432
66C49CB1 36A5B2F8 D77A8C46 5AFE4112 EA5917D9 81542640 80EF2D36 54A85CC6
C3FFFFB8 39A648DD 2ABA2B13 4137BE07 760E46C0 74401DA7 482E3FA2 A64B70FF
447AA1B2 52E37240 29987085 532BBE3B C2E2E54A 54CA1D13 0E
quit
dot11 syslog
ip source-route
ip dhcp excluded-address 10.10.10.1
ip dhcp pool inside
ip dhcp pool lan_network
network 172.20.224.0 255.255.240.0
dns-server 8.8.8.8 8.8.4.4
default-router 172.20.224.1
lease 7
ip cef
no ip domain lookup
ip domain name yourdomain.com
password encryption aes
username pix privilege 15 secret 5 $1$Z.wA$lBmj36AJx/cbK1RjmfGJh1
username admin privilege 15 password 0 434Zaty
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp key password address 217.36.32.222
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto map SDM_CMAP_1 1 ipsec-isakmp
description Tunnel to217.36.32.222
set peer 217.36.32.222
set transform-set ESP-3DES-SHA
match address 100
archive
log config
hidekeys
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 0/38
encapsulation aal5mux ppp dialer
dialer pool-member 1
dsl operating-mode auto
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 172.20.224.1 255.255.240.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
interface Dialer0
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
no cdp enable
ppp authentication chap callin
ppp chap hostname B6*******.btclick.com
ppp chap password 0 H*******
crypto map SDM_CMAP_1
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source route-map SDM_RMAP_1 interface Dialer0 overload
access-list 1 remark CCP_ACL Category=16
access-list 1 permit 172.4.0.0 0.240.255.255
access-list 10 permit 195.12.1.35
access-list 10 permit 172.4.0.0 0.240.255.255
access-list 100 remark CCP_ACL Category=4
access-list 100 remark IPSec Rule
access-list 100 permit ip 172.20.224.0 0.0.15.255 192.168.168.0 0.0.0.255
access-list 101 remark CCP_ACL Category=2
access-list 101 remark IPSec Rule
access-list 101 deny ip 172.20.224.0 0.0.15.255 192.168.168.0 0.0.0.255
access-list 101 permit ip 172.4.0.0 0.240.255.255 any
route-map SDM_RMAP_1 permit 1
match ip address 101
control-plane
banner exec ^C
% Password expiration warning.
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you
want to use.
^C
banner login ^C
Cisco Configuration Professional (Cisco CP) is installed on this device.
This feature requires the one-time use of the username "cisco" with the
password "cisco". These default credentials have a privilege level of 15.
YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE
PUBLICLY-KNOWN CREDENTIALS
Here are the Cisco IOS commands.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want
to use.
IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL
NOT BE ABLE TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
For more information about Cisco CP please follow the instructions in the
QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
^C
line con 0
no modem enable
stopbits 1
line aux 0
line vty 0 4
access-class 10 in
privilege level 15
password 434Zaty
transport input telnet ssh
scheduler max-task-time 5000
end
Any help will be most gratefully recieved.Rick,
Thanks for replying. Here is the output from the 800 Show Crypto command:
interface: Dialer0
Crypto map tag: SDM_CMAP_1, local addr 81.136.160.237
protected vrf: (none)
local ident (addr/mask/prot/port): (172.20.224.0/255.255.240.0/0/0)
remote ident (addr/mask/prot/port): (192.168.168.0/255.255.255.0/0/0)
current_peer 217.36.32.222 port 500
PERMIT, flags={origin_is_acl,}
#pkts encaps: 10928, #pkts encrypt: 10928, #pkts digest: 10928
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0
#pkts not decompressed: 0, #pkts decompress failed: 0
#send errors 2, #recv errors 0
local crypto endpt.: 81.136.160.237, remote crypto endpt.: 217.36.32.222
path mtu 1500, ip mtu 1500, ip mtu idb Virtual-Access2
current outbound spi: 0x0(0)
inbound esp sas:
inbound ah sas:
inbound pcp sas:
outbound esp sas:
outbound ah sas:
outbound pcp sas:
interface: Virtual-Access2
Crypto map tag: SDM_CMAP_1, local addr 81.136.160.237
protected vrf: (none)
local ident (addr/mask/prot/port): (172.20.224.0/255.255.240.0/0/0)
remote ident (addr/mask/prot/port): (192.168.168.0/255.255.255.0/0/0)
current_peer 217.36.32.222 port 500
PERMIT, flags={origin_is_acl,}
#pkts encaps: 10928, #pkts encrypt: 10928, #pkts digest: 10928
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0
#pkts not decompressed: 0, #pkts decompress failed: 0
#send errors 2, #recv errors 0
local crypto endpt.: 81.136.160.237, remote crypto endpt.: 217.36.32.222
path mtu 1500, ip mtu 1500, ip mtu idb Virtual-Access2
current outbound spi: 0x0(0)
inbound esp sas:
inbound ah sas:
inbound pcp sas:
outbound esp sas:
outbound ah sas:
outbound pcp sas:
and this is the running config frm our ASA at HQ:
Result of the command: "sh run"
: Saved
ASA Version 8.2(1)
hostname secure-access
domain-name hhp.com
enable password UWWykvGjAPmxufUo encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.168.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group BT
ip address 217.36.32.222 255.255.255.255 pppoe
interface Vlan12
nameif DMZ
security-level 50
ip address 192.168.169.1 255.255.255.0
interface Vlan22
nameif Wireless_HHP
security-level 100
ip address 172.16.36.1 255.255.254.0
interface Vlan32
nameif CNES
security-level 100
ip address 187.187.168.1 255.255.0.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
switchport access vlan 12
interface Ethernet0/3
switchport access vlan 22
interface Ethernet0/4
switchport access vlan 32
interface Ethernet0/5
switchport access vlan 12
interface Ethernet0/6
switchport access vlan 12
interface Ethernet0/7
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
dns domain-lookup DMZ
dns domain-lookup Wireless_HHP
dns domain-lookup CNES
dns server-group DefaultDNS
name-server 192.168.168.2
domain-name hhp.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network NET-cnes_HHP-Sty
network-object 172.20.224.0 255.255.240.0
object-group network NET-cnes_HHP-Balivanich
network-object 172.20.192.0 255.255.240.0
object-group network Oak-DC1
network-object 192.168.168.2 255.255.255.255
object-group network Maple-DC2
network-object 192.168.168.3 255.255.255.255
object-group network HHP_Domain_Controllers
group-object Oak-DC1
group-object Maple-DC2
object-group network PC-Support
network-object 187.187.60.1 255.255.255.255
network-object 187.187.60.2 255.255.255.254
network-object 187.187.60.4 255.255.255.254
network-object 187.187.60.6 255.255.255.255
object-group network ELM-ActiveH
network-object 192.168.168.6 255.255.255.255
object-group network Pine-GP
network-object 192.168.168.12 255.255.255.255
object-group network HHP_Application_Servers
group-object ELM-ActiveH
group-object Pine-GP
object-group network Fern-TS1
network-object 192.168.168.4 255.255.255.255
object-group network Fir-TS2
network-object 192.168.168.5 255.255.255.255
object-group network HHP_Terminal_Servers
group-object Fern-TS1
group-object Fir-TS2
object-group service Global_Catalog_LDAP
description (Generated by Cisco SM from Object "Global Catalog LDAP")
service-object tcp eq 3268
object-group service Global_Catalog_LDAP_SSL
description (Generated by Cisco SM from Object "Global Catalog LDAP SSL")
service-object tcp eq 3269
object-group service UDP-389
description UDP port for LDAP
service-object udp eq 389
object-group service TCP-88
description TCP Port 88
service-object tcp eq 88
object-group service TCP-445
description SMB
service-object tcp eq 445
object-group network John_-_Laptop
description John's Laptop
network-object 187.187.10.65 255.255.255.255
object-group network Graham_-_PC
description Graham Morrison's PC
network-object 187.187.10.90 255.255.255.255
object-group network john_test
network-object 187.187.40.7 255.255.255.255
object-group network Iain_PC
description Iain Macaulay IT
network-object 187.187.10.19 255.255.255.255
object-group network John_-_PC
description John MacPhail's PC
network-object 187.187.10.7 255.255.255.255
object-group network it-alahen-lap
network-object 187.187.10.230 255.255.255.255
object-group network Catriona_-_Laptop
description Catriona's Laptop
network-object 187.187.10.60 255.255.255.255
object-group network Graham_-_Laptop
network-object 187.186.10.120 255.255.255.255
object-group network it-innive-xp
description Innes MacIver's PC
network-object 187.187.10.14 255.255.255.255
object-group network it-alahen-xp
description Desktop
network-object 187.187.10.229 255.255.255.255
object-group network Cat_-_PC
description Catriona Macmillan's PC
network-object 187.187.10.4 255.255.255.255
object-group network it-davdon-xp
description Desktop
network-object 187.187.160.7 255.255.255.255
object-group network cat-laptop
description Catriona's Laptop addresses
network-object 187.187.77.81 255.255.255.255
network-object 187.187.77.82 255.255.255.255
object-group network Catriona_old_pc
network-object 187.187.10.44 255.255.255.255
object-group network cat-tablet
description Catriona's Tablet ip address's
network-object 187.187.77.78 255.255.255.254
object-group network DSO-SQLServer
description Task Database Server
network-object 187.187.1.33 255.255.255.255
object-group network it-finfernew-xp
description Findlay Ferguson PC
network-object 187.187.10.153 255.255.255.255
object-group network PC_Support
group-object John_-_Laptop
group-object Graham_-_PC
group-object john_test
group-object Iain_PC
group-object John_-_PC
group-object it-alahen-lap
group-object Catriona_-_Laptop
group-object Graham_-_Laptop
group-object it-alahen-xp
group-object Cat_-_PC
group-object it-davdon-xp
group-object cat-laptop
group-object Catriona_old_pc
group-object cat-tablet
group-object it-innive-xp
network-object 187.187.1.128 255.255.255.255
network-object 187.187.10.76 255.255.255.255
group-object DSO-SQLServer
network-object 187.187.15.234 255.255.255.255
network-object 187.187.4.60 255.255.255.255
network-object 187.187.10.134 255.255.255.255
network-object 172.18.194.22 255.255.255.255
group-object it-finfernew-xp
object-group network Entire_CNE
description Entire CNE range
network-object 187.0.0.0 255.0.0.0
object-group network NET-cnes_HHP-Sty-Staff
network-object 172.20.225.0 255.255.255.0
object-group network NET-cnes_HHP-Balivanich-staff
network-object 172.20.193.0 255.255.255.0
object-group network Alder-Intranet
network-object 192.168.168.13 255.255.255.255
object-group network Aspen-ISA
network-object 192.168.168.10 255.255.255.255
object-group service tcp-8080
description TCP Port 8080
service-object tcp eq 8080
object-group network Beech-External
network-object 217.36.32.210 255.255.255.255
object-group network it-csm
description cisco security manager
network-object 187.187.1.72 255.255.255.255
object-group network Juniper-External
description Internet Server
network-object 217.36.32.211 255.255.255.255
object-group network HHP_Server_Network
network-object 192.168.168.0 255.255.255.0
object-group network Messagelabs_Incoming_HHP
network-object 67.219.240.0 255.255.240.0
network-object 95.131.104.0 255.255.248.0
network-object 193.109.254.0 255.255.254.0
network-object 195.245.230.0 255.255.254.0
network-object 216.82.240.0 255.255.240.0
network-object 85.158.136.0 255.255.248.0
network-object 117.120.16.0 255.255.248.0
network-object 194.106.220.0 255.255.254.0
object-group network Angus-Maclean-PC
network-object 187.187.10.250 255.255.255.255
object-group service RDP
service-object tcp eq 3389
object-group network it-dbserver
description Database Server (Live)
network-object 187.187.1.65 255.255.255.255
object-group network it-sql-test
description Test SQL / database server
network-object 187.187.1.81 255.255.255.255
object-group service DNS-Resolving
description Domain Name Server
service-object tcp eq domain
service-object udp eq domain
object-group network Beech-Exchange
network-object 192.168.168.91 255.255.255.255
object-group network Messagelabs_-_Incoming
description List of MessageLab addresses that SMTP connections are accepted from
network-object 212.125.75.0 255.255.255.224
network-object 216.82.240.0 255.255.240.0
network-object 195.216.16.211 255.255.255.255
network-object 194.205.110.128 255.255.255.224
network-object 194.106.220.0 255.255.254.0
network-object 193.109.254.0 255.255.254.0
network-object 62.231.131.0 255.255.255.0
network-object 62.173.108.208 255.255.255.240
network-object 62.173.108.16 255.255.255.240
network-object 212.125.74.44 255.255.255.255
network-object 195.245.230.0 255.255.254.0
network-object 85.158.136.0 255.255.248.0
object-group network MIS_Support
network-object 192.168.168.250 255.255.255.254
object-group network it-donadon-xp
description Donald Macdonald's PC
network-object 187.187.10.13 255.255.255.255
object-group network Angela_PC
network-object 187.187.10.155 255.255.255.255
object-group network Katie_PC
network-object 187.187.10.151 255.255.255.255
object-group network Pauline_PC
network-object 187.187.10.12 255.255.255.255
object-group network it-paye-net
network-object 187.187.1.92 255.255.255.255
object-group network MessageLabs-Towers
description Message Labs IP Address ranges
network-object 216.82.240.0 255.255.240.0
network-object 67.219.240.0 255.255.240.0
network-object 85.158.136.0 255.255.248.0
network-object 95.131.104.0 255.255.248.0
network-object 117.120.16.0 255.255.248.0
network-object 193.109.254.0 255.255.254.0
network-object 194.106.220.0 255.255.254.0
network-object 195.245.230.0 255.255.254.0
network-object 62.231.131.0 255.255.255.0
network-object 212.125.75.16 255.255.255.240
object-group network NET_cnes-castlebay-staff
network-object 172.19.17.0 255.255.255.0
object-group network NET_cnes_tarbert_staff
description NET_cnes_tarbert_staff
network-object 172.19.33.0 255.255.255.0
object-group network Juniper
network-object 192.168.169.5 255.255.255.255
object-group network HHP_DMZ_Network
network-object 192.168.169.0 255.255.255.0
object-group network Ash
network-object 192.168.168.100 255.255.255.255
object-group service UDP-445
service-object udp eq 445
object-group service tcp-udp-135-139
service-object tcp-udp range 135 139
object-group network HHP-ELM
description HHP's ELM ActiveH server
network-object 187.187.1.203 255.255.255.255
object-group network CNES-Ext-GW
description CNES External Address
network-object 194.83.245.242 255.255.255.255
object-group service IPSEC
description IPSEC
service-object 57
service-object ah
service-object esp
service-object udp eq isakmp
object-group network Alamur-PC
network-object 187.187.10.15 255.255.255.255
object-group network Iain-Nicolson-PC
network-object 187.187.10.159 255.255.255.255
object-group network HHP_Remote_Access_Pool
network-object 192.168.168.200 255.255.255.248
network-object 192.168.168.208 255.255.255.240
network-object 192.168.168.224 255.255.255.252
network-object 192.168.168.228 255.255.255.254
object-group network Holly-AV
network-object 192.168.168.9 255.255.255.255
object-group service AVG_Ports
description For AVG server to HHP PCs
service-object tcp-udp eq 6150
service-object tcp-udp eq 6051
service-object tcp-udp eq 445
service-object tcp-udp eq 138
service-object tcp-udp eq 135
service-object tcp-udp eq 6054
service-object tcp-udp eq 4158
service-object tcp-udp eq 139
service-object tcp-udp eq 137
object-group network CNES_Access
network-object 192.168.168.230 255.255.255.254
network-object 192.168.168.232 255.255.255.248
network-object 192.168.168.240 255.255.255.248
network-object 192.168.168.248 255.255.255.254
object-group network HHP-068
description BACS PC
network-object 172.20.225.6 255.255.255.255
object-group network Banyan
network-object 192.168.168.105 255.255.255.255
object-group service TCP81
description TCP Port 81
service-object tcp eq 81
object-group network Gavin_-_new_PC
network-object 187.187.10.150 255.255.255.255
object-group network Secudoors
network-object 172.20.224.4 255.255.255.255
access-list outside_access_in remark Time sync to external ntp server
access-list outside_access_in extended permit udp host 192.108.114.23 object-group HHP_Domain_Controllers eq ntp
access-list outside_access_in extended permit tcp object-group MessageLabs-Towers object-group Beech-External eq smtp
access-list outside_access_in extended permit ip host 81.136.160.237 object-group HHP_Server_Network
access-list outside_access_in extended permit ip object-group CNES_Access object-group HHP_Server_Network
access-list outside_access_in extended permit ip object-group MIS_Support object-group HHP_Server_Network
access-list outside_access_in extended permit ip object-group HHP_Remote_Access_Pool object-group HHP_Server_Network
access-list outside_access_in extended permit tcp any object-group Juniper-External eq www
access-list outside_access_in extended permit tcp any object-group Juniper-External eq https
access-list outside_access_in extended deny ip any any
access-list outside_access_in_1 extended permit ip any any
access-list CSM_FW_ACL_Wireless_HHP extended permit ip object-group NET-cnes_HHP-Balivanich object-group HHP_Server_Network
access-list CSM_FW_ACL_Wireless_HHP extended permit ip object-group NET-cnes_HHP-Sty object-group HHP_Server_Network
access-list CSM_FW_ACL_Wireless_HHP extended permit tcp object-group HHP-068 any eq www
access-list CSM_FW_ACL_Wireless_HHP extended permit tcp object-group HHP-068 any eq domain
access-list CSM_FW_ACL_Wireless_HHP extended permit udp object-group HHP-068 any eq domain
access-list CSM_FW_ACL_Wireless_HHP extended permit tcp object-group HHP-068 any eq https
access-list CSM_FW_ACL_Wireless_HHP extended permit object-group DNS-Resolving object-group HHP-068 any
access-list CSM_FW_ACL_Wireless_HHP extended permit object-group tcp-8080 object-group HHP-068 any
access-list CSM_FW_ACL_Wireless_HHP extended permit ip host 172.20.193.53 object-group CNES-Ext-GW
access-list CSM_FW_ACL_Wireless_HHP extended permit ip object-group Secudoors any
access-list CSM_FW_ACL_inside extended permit ip object-group HHP_Server_Network object-group NET-cnes_HHP-Balivanich
access-list CSM_FW_ACL_inside extended permit ip object-group HHP_Server_Network object-group NET-cnes_HHP-Sty
access-list CSM_FW_ACL_inside extended permit ip object-group HHP_Application_Servers object-group PC_Support
access-list CSM_FW_ACL_inside extended permit ip object-group HHP_Domain_Controllers object-group PC_Support
access-list CSM_FW_ACL_inside extended permit ip object-group HHP_Terminal_Servers object-group PC_Support
access-list CSM_FW_ACL_inside extended permit tcp object-group Oak-DC1 any eq domain
access-list CSM_FW_ACL_inside extended permit udp object-group Oak-DC1 any eq domain
access-list CSM_FW_ACL_inside extended permit object-group DNS-Resolving object-group Oak-DC1 any
access-list CSM_FW_ACL_inside extended permit tcp object-group Maple-DC2 any eq domain
access-list CSM_FW_ACL_inside extended permit udp object-group Maple-DC2 any eq domain
access-list CSM_FW_ACL_inside extended permit object-group DNS-Resolving object-group Maple-DC2 any
access-list CSM_FW_ACL_inside extended permit tcp object-group Aspen-ISA any eq www
access-list CSM_FW_ACL_inside extended permit tcp object-group Aspen-ISA any eq domain
access-list CSM_FW_ACL_inside extended permit udp object-group Aspen-ISA any eq domain
access-list CSM_FW_ACL_inside extended permit tcp object-group Aspen-ISA any eq https
access-list CSM_FW_ACL_inside extended permit object-group DNS-Resolving object-group Aspen-ISA any
access-list CSM_FW_ACL_inside extended permit object-group tcp-8080 object-group Aspen-ISA any
access-list CSM_FW_ACL_inside remark For Symantec Liveupdates
access-list CSM_FW_ACL_inside extended permit tcp object-group Banyan any eq ftp
access-list CSM_FW_ACL_inside extended permit tcp object-group Banyan any eq www
access-list CSM_FW_ACL_inside extended permit tcp object-group Banyan any eq https
access-list CSM_FW_ACL_inside remark IPSec VPN access from ELm to CNES
access-list CSM_FW_ACL_inside extended permit object-group IPSEC object-group ELM-ActiveH object-group CNES-Ext-GW
access-list CSM_FW_ACL_inside extended permit udp object-group ELM-ActiveH object-group CNES-Ext-GW eq 4500
access-list CSM_FW_ACL_inside extended permit tcp object-group ELM-ActiveH object-group CNES-Ext-GW eq 4500
access-list CSM_FW_ACL_inside extended permit icmp object-group HHP_Server_Network object-group HHP_DMZ_Network
access-list CSM_FW_ACL_inside remark Time sync to external ntp server
access-list CSM_FW_ACL_inside extended permit udp object-group HHP_Domain_Controllers host 192.108.114.23 eq ntp
access-list CSM_FW_ACL_inside extended permit tcp object-group Beech-Exchange object-group Messagelabs_-_Incoming eq smtp
access-list CSM_FW_ACL_inside extended permit tcp object-group Aspen-ISA object-group Juniper eq www
access-list CSM_FW_ACL_inside extended permit tcp object-group Aspen-ISA object-group Juniper eq https
access-list CSM_FW_ACL_inside extended permit ip object-group Holly-AV object-group Juniper
access-list CSM_FW_ACL_inside extended deny ip any any
access-list CSM_FW_ACL_CNES extended permit ip object-group PC_Support object-group HHP_Server_Network
access-list CSM_FW_ACL_CNES extended permit ip object-group PC_Support object-group HHP_DMZ_Network
access-list CSM_FW_ACL_CNES extended permit ip object-group PC_Support object-group NET-cnes_HHP-Balivanich
access-list CSM_FW_ACL_CNES extended permit ip object-group PC_Support object-group NET-cnes_HHP-Sty
access-list CSM_FW_ACL_CNES extended permit tcp object-group it-csm any eq ssh
access-list CSM_FW_ACL_CNES extended permit tcp object-group it-csm any eq www
access-list CSM_FW_ACL_CNES extended permit tcp object-group it-csm any eq https
access-list CSM_FW_ACL_CNES remark Aim's access to Active H server: DSO SQL
access-list CSM_FW_ACL_CNES remark server's access (Task)
access-list CSM_FW_ACL_CNES remark IT Ops - mapped drive for FTP transfer to and from E450/Elm of Entitlement Adjustments
access-list CSM_FW_ACL_CNES remark and Tenancy Changes
access-list CSM_FW_ACL_CNES extended permit ip object-group it-sql-test object-group ELM-ActiveH
access-list CSM_FW_ACL_CNES extended permit ip object-group DSO-SQLServer object-group ELM-ActiveH
access-list CSM_FW_ACL_CNES extended permit ip object-group it-paye-net object-group ELM-ActiveH
access-list CSM_FW_ACL_CNES extended permit ip object-group Angela_PC object-group ELM-ActiveH
access-list CSM_FW_ACL_CNES extended permit ip object-group Katie_PC object-group ELM-ActiveH
access-list CSM_FW_ACL_CNES extended permit ip object-group Pauline_PC object-group ELM-ActiveH
access-list CSM_FW_ACL_CNES remark donald and Findlay RDP access to Active H
access-list CSM_FW_ACL_CNES extended permit object-group RDP object-group it-donadon-xp object-group ELM-ActiveH
access-list CSM_FW_ACL_CNES extended permit object-group RDP object-group it-donadon-xp object-group HHP_Terminal_Servers
access-list CSM_FW_ACL_CNES extended permit object-group RDP object-group it-finfernew-xp object-group ELM-ActiveH
access-list CSM_FW_ACL_CNES extended permit object-group RDP object-group it-finfernew-xp object-group HHP_Terminal_Servers
access-list CSM_FW_ACL_CNES extended permit ip object-group Angus-Maclean-PC object-group Alder-Intranet
access-list CSM_FW_ACL_CNES extended permit ip object-group Angus-Maclean-PC host 192.168.168.17
access-list CSM_FW_ACL_CNES extended permit ip object-group Angus-Maclean-PC object-group Juniper
access-list CSM_FW_ACL_CNES extended permit ip object-group Iain-Nicolson-PC object-group Alder-Intranet
access-list CSM_FW_ACL_CNES extended permit ip object-group Iain-Nicolson-PC host 192.168.168.17
access-list CSM_FW_ACL_CNES extended permit ip object-group Iain-Nicolson-PC object-group Juniper
access-list CSM_FW_ACL_CNES extended permit ip object-group it-davdon-xp object-group Alder-Intranet
access-list CSM_FW_ACL_CNES extended permit ip object-group it-davdon-xp host 192.168.168.17
access-list CSM_FW_ACL_CNES extended permit ip object-group it-davdon-xp object-group Juniper
access-list CSM_FW_ACL_CNES extended permit ip object-group Alamur-PC object-group Alder-Intranet
access-list CSM_FW_ACL_CNES extended permit ip object-group Alamur-PC host 192.168.168.17
access-list CSM_FW_ACL_CNES extended permit ip object-group Alamur-PC object-group Juniper
access-list CSM_FW_ACL_CNES extended permit ip object-group Gavin_-_new_PC object-group Alder-Intranet
access-list CSM_FW_ACL_CNES extended permit ip object-group Gavin_-_new_PC host 192.168.168.17
access-list CSM_FW_ACL_CNES extended permit ip object-group Gavin_-_new_PC object-group Juniper
access-list CSM_FW_ACL_CNES extended permit object-group RDP object-group NET_cnes-castlebay-staff object-group HHP_Server_Network
access-list CSM_FW_ACL_CNES extended permit object-group RDP object-group NET_cnes_tarbert_staff object-group HHP_Server_Network
access-list MIS_splitTunnelAcl standard permit 192.168.168.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object-group HHP_Server_Network 192.168.168.250 255.255.255.254
access-list inside_nat0_outbound extended permit ip object-group HHP_Server_Network 192.168.168.224 255.255.255.224
access-list CSM_FW_ACL_DMZ extended permit ip object-group HHP_DMZ_Network object-group PC_Support
access-list CSM_FW_ACL_DMZ extended permit icmp object-group HHP_DMZ_Network object-group HHP_Server_Network
access-list CSM_FW_ACL_DMZ extended permit ip object-group Juniper object-group Angus-Maclean-PC
access-list CSM_FW_ACL_DMZ extended permit ip object-group Juniper object-group Holly-AV
access-list CSM_FW_ACL_DMZ extended permit tcp object-group Juniper object-group Beech-Exchange eq smtp
access-list CSM_FW_ACL_DMZ extended permit tcp object-group Juniper object-group HHP_Domain_Controllers eq domain
access-list CSM_FW_ACL_DMZ extended permit udp object-group Juniper object-group HHP_Domain_Controllers eq domain
access-list CSM_FW_ACL_DMZ remark for backups to USB drive on ASH
access-list CSM_FW_ACL_DMZ extended permit object-group TCP-445 object-group Juniper object-group Ash
access-list CSM_FW_ACL_DMZ extended permit object-group UDP-445 object-group Juniper object-group Ash
access-list CSM_FW_ACL_DMZ extended permit object-group tcp-udp-135-139 object-group Juniper object-group Ash
access-list CSM_FW_ACL_DMZ extended deny ip any any
access-list CNES_Support_splitTunnelAcl standard permit 192.168.168.0 255.255.255.0
access-list RemoteAccess_splitTunnelAcl standard permit 192.168.168.0 255.255.255.0
access-list outside_cryptomap extended permit ip object-group HHP_Server_Network object-group NET-cnes_HHP-Sty
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1492
mtu DMZ 1500
mtu Wireless_HHP 1500
mtu CNES 1500
ip local pool CNES_Access 192.168.168.230-192.168.168.249
ip local pool MIS_Support 192.168.168.250-192.168.168.251
ip local pool OLM-VPN-Pool 192.168.168.252
ip local pool HHP_Remote_Access_Pool 192.168.168.200-192.168.168.229
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
nat (Wireless_HHP) 1 172.20.193.53 255.255.255.255
nat (Wireless_HHP) 1 172.20.225.0 255.255.255.0
static (inside,CNES) 192.168.168.0 192.168.168.0 netmask 255.255.255.0
static (CNES,inside) 187.187.0.0 255.255.0.0 netmask 255.255.0.0
static (Wireless_HHP,inside) 172.20.224.0 172.20.224.0 netmask 255.255.240.0
static (inside,Wireless_HHP) 192.168.168.0 192.168.168.0 netmask 255.255.255.0
static (CNES,Wireless_HHP) 187.187.0.0 187.187.0.0 netmask 255.255.0.0
static (inside,outside) 217.36.32.210 192.168.168.91 netmask 255.255.255.255
static (DMZ,outside) 217.36.32.211 192.168.169.5 netmask 255.255.255.255
static (inside,DMZ) 192.168.168.0 192.168.168.0 netmask 255.255.255.0
static (CNES,DMZ) 187.0.0.0 187.0.0.0 netmask 255.0.0.0
access-group CSM_FW_ACL_inside in interface inside
access-group outside_access_in_1 in interface outside control-plane
access-group outside_access_in in interface outside
access-group CSM_FW_ACL_DMZ in interface DMZ
access-group CSM_FW_ACL_Wireless_HHP in interface Wireless_HHP
access-group CSM_FW_ACL_CNES in interface CNES
route outside 0.0.0.0 0.0.0.0 81.148.0.157 1
route Wireless_HHP 172.20.192.0 255.255.240.0 172.16.36.3 1
route Wireless_HHP 172.20.224.0 255.255.240.0 172.16.36.2 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server HHP protocol ldap
aaa-server HHP (inside) host 192.168.168.2
timeout 5
ldap-base-dn dc=hhp,dc=com
ldap-scope subtree
ldap-naming-attribute sAMAccountName
ldap-login-password *
ldap-login-dn cn=gramor,cn=users,dc=hhp,dc=com
server-type microsoft
aaa-server HHP_1 protocol ldap
aaa-server HHP_1 (inside) host 192.168.168.2
timeout 5
ldap-base-dn dc=hhp,dc=com
ldap-scope subtree
ldap-naming-attribute sAMAccountName
ldap-login-password *
ldap-login-dn cn=administrator,cn=users,dc=hhp,dc=com
server-type microsoft
aaa-server HHP_3 protocol ldap
aaa-server HHP_3 (inside) host 192.168.168.2
timeout 5
ldap-base-dn dc=hhp,dc=com
ldap-scope subtree
ldap-naming-attribute sAMAccountName
ldap-login-password *
ldap-login-dn cn=administrator,cn=users,dc=hhp,dc=com
server-type microsoft
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 192.168.168.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 outside
http 194.83.245.242 255.255.255.255 outside
http 187.187.1.72 255.255.255.255 CNES
http 187.187.10.90 255.255.255.255 CNES
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map outside_map_dynamic 2 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 81.136.160.237
crypto map outside_map 1 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 30001 ipsec-isakmp dynamic outside_map_dynamic
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ca trustpoint ASDM_TrustPoint0
enrollment terminal
fqdn none
subject-name O=Hebridean Housing Partnership Limited,CN=secure-access.hebrideanhousing.co.uk,L=Isle of Lewis,ST=Scotland,C=GB
keypair SSL_Certificate
crl configure
crypto ca trustpoint ASDM_TrustPoint1
enrollment terminal
fqdn none
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate 0100000000012790a5c005
30820530 30820418 a0030201 02020b01 00000000 012790a5 c005300d 06092a86
4886f70d 01010505 00306a31 23302106 0355040b 131a4f72 67616e69 7a617469
6f6e2056 616c6964 6174696f 6e204341 31133011 06035504 0a130a47 6c6f6261
6c536967 6e312e30 2c060355 04031325 476c6f62 616c5369 676e204f 7267616e
697a6174 696f6e20 56616c69 64617469 6f6e2043 41301e17 0d313030 33323431
34313835 385a170d 31333033 32343134 31383534 5a308197 310b3009 06035504
06130247 42311130 0f060355 04081308 53636f74 6c616e64 31163014 06035504
07130d49 736c6520 6f66204c 65776973 312e302c 06035504 0a132548 65627269
6465616e 20486f75 73696e67 20506172 746e6572 73686970 204c696d 69746564
312d302b 06035504 03132473 65637572 652d6163 63657373 2e686562 72696465
616e686f 7573696e 672e636f 2e756b30 82012230 0d06092a 864886f7 0d010101
05000382 010f0030 82010a02 82010100 def181d9 c34c58a8 9abcc849 7d8ad0a9
3c64c77f f3126c81 30911f41 5903a92c 81fb374b 2fe2680e 10b26dce 81ca0c23
af2c9f9a 52295e8c d2223fa6 7c4c386d 51c6fb16 a47688e6 e47e2410 b0283503
fd72abd3 e59d3b02 cd47706e babf948c 4e0282a3 5f789ff7 8041b2db ceac64eb
3e163b38 3a8ecc25 0c4802a8 d17fecd9 f1a36288 29202df4 b20ae891 f95ce055
6e670559 3d075024 7f3ac7ef 26218154 a7f6a399 34c43c4a 97c2c88c c4588ee4
77cc2ad8 b1bd868d d55c2b9b 727e9904 66d0fb52 c212abd7 a06f28f1 ad2aa04b
3d7b3094 c59c00d4 cf51fefb d8bfa101 8ba9c4ba 5cf629ff c50716d3 71019a98
8fa55b83 6b158b6d 1043f092 646ef07d 02030100 01a38201 a7308201 a3301f06
03551d23 04183016 80147d6d 2aec66ab a75136ab 0269f170 8fc4590b 9a1f3049
06082b06 01050507 0101043d 303b3039 06082b06 01050507 3002862d 68747470
3a2f2f73 65637572 652e676c 6f62616c 7369676e 2e6e6574 2f636163 6572742f
6f726776 312e6372 74303f06 03551d1f 04383036 3034a032 a030862e 68747470
3a2f2f63 726c2e67 6c6f6261 6c736967 6e2e6e65 742f4f72 67616e69 7a617469
6f6e5661 6c312e63 726c301d 0603551d 0e041604 14d398d5 ddf29355 15b04750
baccc6b3 0f97a6c9 94302f06 03551d11 04283026 82247365 63757265 2d616363
6573732e 68656272 69646561 6e686f75 73696e67 2e636f2e 756b3009 0603551d
13040230 00300e06 03551d0f 0101ff04 04030205 a0302906 03551d25 04223020
06082b06 01050507 03010608 2b060105 05070302 060a2b06 01040182 370a0303
304b0603 551d2004 44304230 4006092b 06010401 a0320114 30333031 06082b06
01050507 02011625 68747470 3a2f2f77 77772e67 6c6f6261 6c736967 6e2e6e65
742f7265 706f7369 746f7279 2f301106 09608648 0186f842 01010404 030206c0
300d0609 2a864886 f70d0101 05050003 82010100 8af3be01 c4830d83 9b347355
de7496ef bd76b86c ee92f32f 1157ef11 6ad949b6 611537ad 81f06408 73ec6fe2
6466675c cf31a80f bead422d ec574f95 55fe0b7a 97e271e7 0220c7b1 53376843
ff7f7280 f9bfdee6 3584e123 00c37d9f 5004b766 9469ead5 f002744c fd50271c
6bcdb54c e5db85aa 9760a330 d72464a2 bc8ecdff d80bbc27 7551e97c ee9b7078
9207f9d6 b969a47a 6df722b6 14ce803d 8d4bb9e9 4695e8e6 d453950e 06506594
ec7652ea 365cdf94 90e2f7ee 855dadb5 c0459d73 bb6d01a8 3c076718 7f80de40
c5eb9e0e 17c93087 fd5c5fc1 fd6401fe 7e5038b1 3da1d250 01ccd8be 964d5557
b320c4c1 0015d1b7 daad7527 930b0c90 7711704f
quit
crypto ca certificate chain ASDM_TrustPoint1
certificate ca 0400000000011e44a5f52a
30820467 3082034f a0030201 02020b04 00000000 011e44a5 f52a300d 06092a86
4886f70d 01010505 00305731 0b300906 03550406 13024245 31193017 06035504
0a131047 6c6f6261 6c536967 6e206e76 2d736131 10300e06 0355040b 1307526f
6f742043 41311b30 19060355 04031312 476c6f62 616c5369 676e2052 6f6f7420
4341301e 170d3037 30343131 31323030 30305a17 0d313730 34313131 32303030
305a306a 31233021 06035504 0b131a4f 7267616e 697a6174 696f6e20 56616c69
64617469 6f6e2043 41311330 11060355 040a130a 476c6f62 616c5369 676e312e
302c0603 55040313 25476c6f 62616c53 69676e20 4f726761 6e697a61 74696f6e
2056616c 69646174 696f6e20 43413082 0122300d 06092a86 4886f70d 01010105
00038201 0f003082 010a0282 010100a1 2fc4bcce 8703e967 c189c8e5 93fc7db4
ad9ef663 4e6ae89c 2c7389a2 01f48f21 f8fd259d 58166d86 f6ee4957 757e75ea
22117e3d fbc74241 dcfcc50c 9155807b eb64331d 9bf9ca38 e9abc625 43512540
f4e47e18 556aa98f 103a401e d65783ef 7f2f342f 2dd2f653 c2190db7 edc981f5
462cb423 425e9d13 0375ecea 6afc577c c936973b 98dc1313 ecec41fa 5d34eab9
93e71016 65cc9c92 fdf5c59d 3e4ab909 fce45f1e 695f4df4 567244b1 1d2303c8
36f66588 c8bf3916 458e1e26 6c5116c5 2a0038c5 a4136995 7dab013b a8c414b4
80daac1a 4420d5fe a9067b14 27afe030 21dd90f4 a9d52319 2e1e03e6 c1df9529
e4c19443 dd3e90aa cb4bc9be 8ad33902 03010001 a382011f 3082011b 300e0603
551d0f01 01ff0404 03020106 30120603 551d1301 01ff0408 30060101 ff020100
301d0603 551d0e04 1604147d 6d2aec66 aba75136 ab0269f1 708fc459 0b9a1f30
4b060355 1d200444 30423040 06092b06 010401a0 32011430 33303106 082b0601
05050702 01162568 7474703a 2f2f7777 772e676c 6f62616c 7369676e 2e6e6574
2f726570 6f736974 6f72792f 30330603 551d1f04 2c302a30 28a026a0 24862268
7474703a 2f2f6372 6c2e676c 6f62616c 7369676e 2e6e6574 2f726f6f 742e6372
6c301106 09608648 0186f842 01010404 03020204 30200603 551d2504 19301706
0a2b0601 04018237 0a030306 09608648 0186f842 0401301f 0603551d 23041830
16801460 7b661a45 0d97ca89 502f7d04 cd34a8ff fcfd4b30 0d06092a 864886f7
0d010105 05000382 01010079 47fc15d7 4c79df0f 7a9eced4 7c4b63c9 89b57b3f
9912e89c 8c9a492f e04e954a edc7bcbe f1a2db8e 931dba71 54aa4bd9 89222487
c504a8ac 8252a052 f8b8e14f a1276663 214a39e7 c7c54e5f b2d61d13 6d30e9ce
d7a21cbc 290a733c 5b2349fe d6ffcab0 4ff5f267 98c04711 f8b748a6 9009d642
beeab1b9 5342c39c 20c9fba1 5bb5566d 8781c860 acc4b972 270a8e1e a8b12ecd
32a27857 b09cf895 bb438e8c 31866e53 0dc61205 ba416ea8 35300918 1d0261ff
fdee35de 6ac33bd0 4d4b4e50 b256360c 445dda1a 652ae698 56a96333 2e04e7ae
e8f48eb7 b2da7dc0 c8e2aea6 282fe3c9 73bdfc07 4134b7aa 6eeea7db d1933ced
90ec3292 88d9c823 6c7421
quit
crypto isakmp identity hostname
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash sha
group 1
lifetime 86400
telnet 0.0.0.0 0.0.0.0 inside
telnet timeout 5
ssh 187.187.1.41 255.255.255.255 inside
ssh 187.187.1.72 255.255.255.255 inside
ssh 187.187.77.81 255.255.255.255 inside
ssh 187.187.10.19 255.255.255.255 inside
ssh 187.187.10.229 255.255.255.255 inside
ssh 187.187.160.7 255.255.255.255 inside
ssh 187.187.1.41 255.255.255.255 outside
ssh 187.187.1.72 255.255.255.255 outside
ssh 187.187.77.81 255.255.255.255 outside
ssh 187.187.10.19 255.255.255.255 outside
ssh 187.187.10.229 255.255.255.255 outside
ssh 187.187.160.7 255.255.255.255 outside
ssh timeout 15
console timeout 0
vpdn group BT request dialout pppoe
vpdn group BT localname B*******.btclick.com
vpdn group BT ppp authentication chap
vpdn username B*******@hg39.btclick.com password *********
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl trust-point ASDM_TrustPoint0 outside
ssl trust-point ASDM_TrustPoint0 outside vpnlb-ip
webvpn
enable inside
enable outside
group-policy HHP_Remote_Access_1 internal
group-policy HHP_Remote_Access_1 attributes
wins-server value 192.168.168.2 192.168.168.2
dns-server value 192.168.168.2 192.168.168.3
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value CNES_Support_splitTunnelAcl
group-policy HHP_Remote_Access internal
group-policy HHP_Remote_Access attributes
wins-server value 192.168.168.2 192.168.168.2
dns-server value 192.168.168.2 192.168.168.3
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value CNES_Support_splitTunnelAcl
group-policy Omfax internal
group-policy Omfax attributes
wins-server value 192.168.168.2 192.168.168.3
dns-server value 192.168.168.2 192.168.168.3
vpn-tunnel-protocol IPSec webvpn
webvpn
svc ask none default webvpn
group-policy MIS_1 internal
group-policy MIS_1 attributes
wins-server value 192.168.168.2 192.168.168.3
dns-server value 192.168.168.2 192.168.168.3
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value MIS_splitTunnelAcl
default-domain value hhp.com
group-policy RemoteAccess internal
group-policy RemoteAccess attributes
wins-server value 192.168.168.2 192.168.168.3
dns-server value 192.168.168.2 192.168.168.3
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value RemoteAccess_splitTunnelAcl
group-policy CNES_Access internal
group-policy CNES_Access attributes
wins-server value 192.168.168.2 192.168.168.3
dns-server value 192.168.168.2 192.168.168.3
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value CNES_Support_splitTunnelAcl
group-policy HHP internal
group-policy HHP attributes
dhcp-network-scope none
vpn-access-hours none
vpn-idle-timeout none
vpn-session-timeout none
vpn-filter none
vpn-tunnel-protocol IPSec webvpn
password-storage disable
ip-comp disable
re-xauth disable
group-lock none
pfs disable
ipsec-udp disable
split-tunnel-policy tunnelall
split-tunnel-network-list none
split-dns none
secure-unit-authentication disable
user-authentication disable
user-authentication-idle-timeout none
ip-phone-bypass disable
leap-bypass disable
nem disable
backup-servers keep-client-config
client-firewall none
webvpn
url-list value Severs
filter none
homepage none
port-forward disable
http-proxy disable
sso-server none
svc dtls none
svc keep-installer none
svc rekey time none
svc rekey method none
svc dpd-interval client none
svc dpd-interval gateway none
svc compression none
svc modules none
svc profiles none
svc ask none default webvpn
customization none
http-comp none
user-storage none
storage-key none
hidden-shares none
smart-tunnel disable
activex-relay disable
file-entry disable
file-browsing disable
url-entry disable
deny-message none
group-policy MIS internal
group-policy MIS attributes
wins-server value 192.168.168.2 192.168.168.3
dns-server value 192.168.168.2 192.168.168.3
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value MIS_splitTunnelAcl
username test password Kg/Rgy23do7gPGTv encrypted privilege 0
username test attributes
vpn-group-policy HHP_Remote_Access
username catneil password yOgiHCGobUNIkjcN encrypted privilege 0
username omfax password pvUaCLwilGmQVifd encrypted privilege 0
username backup password IHQbl.JAoESlM9Jv encrypted privilege 0
username misadmin password 8IZXmHa67HIJYHK1 encrypted
username misadmin attributes
service-type remote-access
username gramor password ne829U0rGFVEedhY encrypted privilege 15
username gramor attributes
vpn-group-policy HHP_Remote_Access
webvpn
url-list value Severs
username aim_user password 5OQaWCdB18qiHlOn encrypted privilege 0
username aim_user attributes
vpn-group-policy CNES_Support
username katask password 2WsX.HoqKXuiqkDk encrypted privilege 0
username katask attributes
vpn-group-policy CNES_Support
username janboyd password ZEUyykwzME6hII2i encrypted privilege 0
username marmor password C5n48AiRLXwxAeBQ encrypted privilege 0
username marste password amwTL584WdiT87Tb encrypted privilege 0
username helmah password RvU8c.3w0H3/MJz4 encrypted privilege 0
username anglea password wGlUJDBrmJI.uz./ encrypted privilege 0
username anglea attributes
vpn-group-policy CNES_Support
username fiobuc password 5Uispw90wqvDYerQ encrypted privilege 0
tunnel-group DefaultRAGroup general-attributes
authentication-server-group HHP_1
tunnel-group DefaultWEBVPNGroup general-attributes
authentication-server-group HHP_1
default-group-policy HHP
tunnel-group DefaultWEBVPNGroup webvpn-attributes
nbns-server 192.168.168.2 timeout 2 retry 2
nbns-server 192.168.168.3 timeout 2 retry 2
tunnel-group WebVPN type remote-access
tunnel-group WebVPN general-attributes
authentication-server-group HHP_3
default-group-policy HHP
username-from-certificate UID
tunnel-group CNES_Access -
Connectivity Issue between ASA 5520 firewall and Cisco Call Manager
Recently i have installed ASA 5520 firewall, Below is the detail for my network
ASA 5520 inside ip: 10.12.10.2/24
Cisco Switch 3560 IP: 10.12.10.1/24 for Data and 10.12.110.2/24 for Voice
Cisco Call Manager 3825 IP: 10.12.110.2/24
The users and the IP phone are getting IP from the DHCP server which configured on cisco 3560 Switch.
the Default Gateway for Data user is 10.12.10.2/24 and
for the voice users is 10.12.110.2/24
now the problem is that the users is not able to ping 10.12.110.2 call manager. please if somebody can help in this regard. i will appreciate the prompt response against this issues.Actually i don't wana to insert new subnet and complicate the nework. i need a simple way to solve the problem. below is the details for the asa 5520 config.
ASA Version 8.2(1)
name x.x.x.x Mobily
interface GigabitEthernet0/0
nameif inside
security-level 99
ip address 10.12.10.2 255.255.255.0
interface GigabitEthernet0/1
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.252
object-group service DM_INLINE_SERVICE_1
service-object tcp-udp
service-object ip
service-object icmp
service-object udp
service-object tcp eq ftp
service-object tcp eq www
service-object tcp eq https
service-object tcp eq ssh
service-object tcp eq telnet
access-list RA_VPN_splitTunnelAcl_1 standard permit Inside-Network 255.255.255.0
access-list RA_VPN_splitTunnelAcl standard permit Inside-Network 255.255.255.0
access-list inside_nat0_outbound extended permit ip Inside-Network 255.255.255.0 10.12.10.16 255.255.255.240
access-list inside_nat0_outbound extended permit object-group DM_INLINE_SERVICE_1 10.12.10.16 255.255.255.240 Inside-Network 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip Inside-Network 255.255.255.0 10.12.10.16 255.255.255.240
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu mgmt 1500
ip local pool VPN-Pool 172.16.1.1-172.16.1.30 mask 255.255.255.0
ip local pool VPN-Users 10.12.10.21-10.12.10.30 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-641.bin
asdm history enable
arp timeout 14400
global (inside) 2 interface
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound_1
nat (inside) 1 Inside-Network 255.255.255.0
route outside 0.0.0.0 0.0.0.0 Mobily 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http Mgmt-Network 255.255.255.0 mgmt
http Inside-Network 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet Inside-Network 255.255.255.0 inside
telnet timeout 5
ssh Inside-Network 255.255.255.255 inside
<--- More ---> ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy RA_VPN internal
group-policy RA_VPN attributes
dns-server value 86.51.34.17 8.8.8.8
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value RA_VPN_splitTunnelAcl
username admin password LPtK/u1LnvHTA2vO encrypted privilege 15
tunnel-group RA_VPN type remote-access
tunnel-group RA_VPN general-attributes
address-pool VPN-Users
default-group-policy RA_VPN
tunnel-group RA_VPN ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:e5a64fa92ae465cd7dabd01ce605307d
: end -
IPSEC between Fortinet and Cisco SA540
Hi,
We have done the site to site VPN between Fortinet and Cisco SA540. Everything is configured at both ends but the tunnel is not establised. Can you help me out to resolve the issue.
Regards,
Satish.Hello Venkatasatish,
I gonna send you an example of VPN between Cisco ASA 8.2 version and Fortigate mr4.
In my example i gonna use the following environments:
Cisco ASA "Zones"
Inside: 192.168.1.0/24 "Asa inside interface Ip address 192.168.1.1"
Outside: 200.200.200.0/29 "Asa outside interface Ip address 200.200.200.1"
Fortigate "Zones"
inside: 172.16.1.0/24 "Asa inside interface Ip address 172.16.1.1"
outside: 201.201.201.0/29 "Asa outside interface Ip address 201.201.201.1"
=================================> VPN Script of ASA <=================================
access-list inside_access_in remark Firewall rule from ASA to Fortigate
access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 172.16.1.0 255.255.255.0 log notifications
access-group inside_access_in in interface inside
access-list VPN_NONAT remark Nonat to VPN traffic over VPN
access-list VPN_NONAT extended permit ip 192.168.1.0 255.255.255.0 172.16.1.0 255.255.255.0
access-list CryptoMap_ASA_to_Fortigate remark VPN Site-to-Site to Fortigate Site
access-list CryptoMap_ASA_to_Fortigate extended permit ip 192.168.1.0 255.255.255.0 172.16.1.0 255.255.255.0
nat (inside) 0 access-list VPN_NONAT
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto map OUTSIDE_map 1 match address CryptoMap_ASA_to_Fortigate
crypto map OUTSIDE_map 1 set peer 201.201.201.1
crypto map OUTSIDE_map 1 set transform-set ESP-3DES-SHA
crypto map OUTSIDE_map 1 set security-association lifetime seconds 3600
crypto map OUTSIDE_map interface outside
group-policy GP_TO_FORTIGATE internal
group-policy GP_TO_FORTIGATE attributes
vpn-idle-timeout none
vpn-tunnel-protocol IPSec
tunnel-group 201.201.201.1 type ipsec-l2l
tunnel-group 201.201.201.1 general-attributes
default-group-policy GP_TO_FORTIGATE
tunnel-group 201.201.201.1 ipsec-attributes
pre-shared-key cisco123
=================================> VPN Script for Fortigate ==============================
Phase 1:
FORTIGATE# config vpn ipsec phase1-interface "enter"
FORTIGATE (phase1-interface) # edit 200.200.200.1 "enter"
set interface "outside"
set keylife 86400
set mode main
set dhgrp 2
set proposal 3des-sha1
set remote-gw 200.200.200.1
set psksecret ENC cisco123
next "to apply the configuration"
Phase 2
FORTIGATE# config vpn ipsec phase2-interface
edit 200.200.200.1
set keepalive enable
set pfs disable
set phase1name "200.200.200.1"
set proposal 3des-sha1
set dst-subnet 192.168.1.0 255.255.255.0
set keylifeseconds 3600
set src-subnet 172.16.1.0 255.255.255.0
next "to apply the configuration"
Config route to VPN: I am using 100 entry, you need to take a look at your firewall.
FORTIGATE# config router static "enter"
FORTIGATE (static) # edit 100 "enter"
FORTIGATE (100) # set device "200.200.200.1"
set distance 1
set dst 192.168.1.0 255.255.255.0
Create a Rule: in my example I´m using any to any over VPN, but you can to filter based on network environments.
FORTIGATE # config firewall policy "enter"
FORTIGATE (policy) # edit 100 "enter"
config firewall policy
edit 100
set srcintf "200.200.200.1"
set dstintf "inside"
set srcaddr "all"
set dstaddr "all"
set action accept
set schedule "always"
set service "ANY"
set logtraffic enable
set comments "Access from VPN ASA site"
FORTIGATE (policy) # edit 101 "enter"
config firewall policy
edit 101
set srcintf "inside"
set dstintf "200.200.200.1"
set srcaddr "all"
set dstaddr "all"
set action accept
set schedule "always"
set service "ANY"
set logtraffic enable
set comments "Access to VPN ASA Site"
After that, please start a traffic between private network, 192.168.1.0 and 172.16.1.0/24.
Please let me know about it!
Good luck.
Fabio Jorge Amorim -
Can i use same address pool for different remote access VPN tunnel groups and policy
Hi all,
i want to create a different remote access VPN profile in ASA. ihave one RA vpn already configured for some purpose.
can i use the same ip address pool used for the existing one for the new tunnel-group (to avoid add rotuing on internal devices for new pool) and its a temporary requirement)
thanks in advance
ShnailThanks Karsten..
but still i can have filtering right? iam planning to create a new group policy and tunnelgroup and use the existing pool for new RA and i have to do some filetring also. for the new RA i have to restrict access to a particualr server ,my existing RA have full access.
so iam planning to create new local usernames for the new RA and new group policy with vpn-filter value access-list to apply for that user as below, this will achive waht i need right??
access-list 15 extended permit tcp any host 192.168.205.134 eq 80
username test password password test
username test attributes
vpn-group-policy TEST
vpn-filter value 15
group-policy TEST internal
group-policy TEST attributes
dns-server value 192.168.200.16
vpn-filter value 15
vpn-tunnel-protocol IPSec
address-pools value existing-pool
tunnel-group RAVPN type ipsec-ra
tunnel-group RAVPN general-attributes
address-pool existing-pool
default-group-policy TEST
tunnel-group Payroll ipsec-attributes
pre-shared-key xxx -
Split Tunnel VPN and routing public ip traffic
Hi Everyone,
I have my split tunnel vpn working well but I need to make an adjustment. We have a few systems in the "cloud" and we only allow access from our corporate WAN IP to those servers. I need to be able to access those servers via VPN connection to the office. I added that public IP subnet to my interesting traffic and the vpn client is sending the traffic across the VPN as expected. The issue is that it somehow drops out inside the firewall it seems. Almost like it doesn't know how to route that request back out to the internet using it's own default gateway. Any thoughts as to what I may be missing, here is some of the relevant code
same-security-traffic permit intra-interface
----Interesting Traffic------
access-list vpnpool standard permit 10.1.1.0 255.255.255.0
access-list vpnpool standard permit 10.31.26.0 255.255.255.0
access-list vpnpool standard permit 10.31.61.0 255.255.255.0
access-list vpnpool standard permit 10.31.3.128 255.255.255.192
access-list vpnpool standard permit 10.31.40.128 255.255.255.240
access-list vpnpool standard permit 10.31.40.64 255.255.255.192
access-list vpnpool standard permit 50.57.0.0 255.255.0.0 -- Network of cloud servers
---Natting----------
global (outside) 1 71.174.57.78
global (dmz) 1 interface
nat (inside) 0 access-list 101
nat (inside) 1 10.1.1.0 255.255.255.0
nat (qa) 1 200.200.200.0 255.255.255.0
nat (dmz) 1 10.1.11.0 255.255.255.0
nat (dmz2) 1 192.168.1.0 255.255.255.0
---Rules and Gateway-------
access-group inbound in interface outside
access-group dmz in interface dmz
route outside 0.0.0.0 0.0.0.0 71.174.57.1 1
---VPN-----
group-policy xxx-remote internal
group-policy xxx-remote attributes
wins-server value 10.1.1.5
dns-server value 10.1.1.5 10.1.1.6
vpn-idle-timeout 60
vpn-tunnel-protocol IPSec l2tp-ipsec webvpn
ipsec-udp enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpnpool
default-domain value xxx.local
split-dns value xxxx.local
service-type remote-access
tunnel-group xxx-vpn type remote-access
tunnel-group xxx-vpn general-attributes
address-pool vpnpool
authentication-server-group (outside) RADIUS
authentication-server-group (dmz) RADIUS
default-group-policy xxx-remote
tunnel-group xxx-vpn ipsec-attributes
pre-shared-key xxxxxThat was my mistake, I am mixing up code here. The fun of switching between new and old ASA code as well as routers
Let's do it this way, this should fix the problem. Put the NAT command the way it was as follows:
nat (Outside) 1 10.1.10.0 255.255.255.0
Now we add a NAT0 for the Outside interface. You can reuse the ACL we made if you want or make a new one, your call since you have to administrate it.
no access-list VPN-NAT
access-list VPN-NAT0 permit ip 10.1.10.0 255.255.255.0 10.0.0.0 255.0.0.0
nat (Outside) 0 access-list VPN-NAT0
Now, this should properly NAT the traffic going to the Internet while excluding the traffic destined for your 10.0.0.0/8 subnet using the Nat 0.
Sorry for the round about fix, but that should take care of it. -
Oracle performance, slow for larger and more complex results.
Hello Oracle forum,
At the moment i have a Oracle database running and i'm specifically interested in the efficiency spatial extension for webmaps and GIS.
I've been testing the database with large shape files (400mb - 1gigabyte) loaded them into the database with shp2sdo->sql*loader.
Using Benchmark factory i've test the speed of transactions an these drop relatively quickly. I've started with a simple query:
SELECT id FROM map WHERE id = 3 when I increase the amount of id's to 3-10000 the performance decreases drastically.
so :
SELECT id FROM map WHERE id >=3 and id <= 10000
The explain plan shows the second query , both query's use the index.
| Id | Operation | Name | Rows | Bytes | Cost (%CPU)| Time |
| 0 | SELECT STATEMENT | | 9828 | 49140 | 22 (0)| 00:00:01 |
|* 1 | INDEX RANGE SCAN| SYS_C009650 | 9828 | 49140 | 22 (0)| 00:00:01 |
Statistics
0 recursive calls
0 db block gets
675 consistent gets
0 physical reads
0 redo size
134248 bytes sent via SQL*Net to client
7599 bytes received via SQL*Net from client
655 SQL*Net roundtrips to/from client
0 sorts (memory)
0 sorts (disk)
9796 rows processed
The statistics does not show very weird stuff, but maybe i'm wrong. Nothing changed in the explain plan except for the range scan instead of a unique scan.
The query returns lots of results and this is I think the reason why my measured time of the query is large. The time it takes returning large amount of rows increases quickly for more rows.
. Can this be solved? The table has been analyzed before starting the query.
The parameters of the database are not really changed from standard, I increased the amount of memory used by Oracle 11g to 1+ gigabyte.
and let the database itself decide how it uses this memory.
The system specs are and db_parameters are:
Oracle 11G
Memory Processor # of CPUs OS OS Version OS B
1.99 gb Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz 2 Microsoft WindowsXP 5.2600
0=Oracle decides which value will be given
cursor_sharing EXACT
cursor_space_for_time FALSE
db_block_size 8192
db_recovery_file_dest_size 2147483648
diagnostic_dest C:\DBBENCHMARK\ORACLE
dispatchers (PROTOCOL=TCP) (SERVICE=gistestXDB)
hash_area_size 131072
log_buffer 5656576
memory_max_target 1115684864
memory_target 1048576000
open_cursors 300
parallel_max_servers 20
pga_aggregate_target 0
processes 150
resumable_timeout 2162688
sort_area_size 65536
Sga=632mb
PGA=368mb
javapool=16mb
largepool=8mb
other=8mb
So I indexed and analyzed the data what did i forget? I can speed it up with soft parsing, but the problem remains . Hopefully this enough information for some analysis, does anyone experienced the same problems ? I tested with SQLdeveloper the speed and is shows the same speed as Benchmark factory. What could be wrong with the parameters?
Thanks,
Jan Martijn
Edited by: user12227964 on 25-jan-2010 4:53
Edited by: user12227964 on 26-jan-2010 2:20Sand wrote:
select count(id) , resulted in 3669015 counted id's.
The database counted 18,345,075 rows per second without binded variables , which is ten times slower as your result. This can be possible because of hardware but my question is specifically about the number of rows returned thus large amount of results. The idea was not to compare the speed of "+select count(*)+" statements - but to illustrate that even when dealing with a huge number of rows, one can decrease the amount of I/O that needs to be performed to deal with that number of rows.
Select id from map where id <= 1
4000 rows per second are selected, Rows/sec is a meaningless measurement - due to physical I/O (PIO) versus logical I/O (LIO). You can select a 100 rows and these require PIO. Resulting in an elapsed time of 1 sec. You can select a 1000 rows that require only LIO. With an an elapsed time of 0.5 sec.
Is the 2nd method better or faster? No. It simply needed less time to be spend on I/O as the data blocks were in the buffer cache (memory) and did not require very slow and expensive disk access.
Another database i testes returns 6 times 25425 rows back per second for the same query (100 ids). What could be a parameter that limits the output speed of multiple rows in a query?.Every single row that needs to be read/processed by a SQL statement has a cost associated with it. This cost is not consistent! It differs depending on how that row can reached - what I/O paths are available to find that rows? Does the full table need to be scanned? Does an index need to be scanned? Is there a unique index that can be used? Is the table partitioned and can partitioning pruning be applied and local partition indexes used? Are there are user functions that need to be applied to the row's data? Etc. Etc.
All these together determine how fast the client gets a row from the cursor executing that SQL.
The more rows you want to process, the bigger the increase in the cost/expense - specifically more I/O. As I/O is the biggest expense (slowest ito elapsed time).
So you want to do as little I/O as possible and read as little data as possible. For example, instead of a full table scan, a fast full index scan. For example, instead of reading the complete contents of a 10GB table, reading the complete contents of a 12MB index for that table.
I suggest that you read the Oracle Performance Guide to familiarise yourself with basic performance concepts. Use http://tahiti.oracle.com for finding the the guide for your applicable Oracle version. -
What is the difference in the features between Cisco prime 1.2 and Cisco prime 1.4 ?
Dears,
Please i need to know what is the difference in the features between Cisco prime infrastructure 1.2 and Cisco prime 1.4.
Already i see the release note for each one but the release indicate only the New feature for every one. so i need to know the difference between them not new features.
Wait your kind feedback plz
Regards,Hi,
New Features and Enhancements
The following topics describe new features and enhancements in Cisco Prime Infrastructure 1.4.
Management Support for WLC Release 7.5
Support for 802.11ac Module
Support for Cisco AP 700
Policy Classification Engine
FlexConnect Audit Support
Autonomous AP Support
Client Stateful Switchover
Cable Modem Monitoring
Support for Secure File Transfer Protocol
and please go through the link and check the data sheet for further clearance.
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-infrastructure/datasheet-c78-729879.html -
Anyconnect tunnel-group and group-policy from LDAP
Recently we've changed from LOCAL to LDAP authentication and added additional group-policies for different users to increase security.
To prevent users from selecting an incorrect group-policy, the LDAP server provides a IETF-Radius-Class value which matches the different group-policy names.
It is my understanding that the authentication method is provided by the tunnel-group.
tunnel-group DefaultWEBVPNGroup general-attributes
authentication-server-group LDAP_AD
This all works, but for _one_ of the group policies i'd like to enable (external) two factor authentication. Two enable two factor auth a 'secondary-authentication-server-group' needs to be set in the tunnel-group.
Creating a tunnel-group which maches the name of the group-policy doesn't seem to have any effect. When listing the connected users via "show vpn-sessiondb anyconnect", it always states the correct Group Policy but also always DefaultWEBVPNGroup.
When enabling the listing of tunnel-groups for webvpn, thus allowing users to select their own tunnel-group, the two factor auth does work.
To summarize, is it possible to let LDAP decide which tunnel-group is used or is there another way to have different group policies without users being able to choose ?Fabian,
Your connection lands on a tunnel group and picks a group policy.
A typical way to overcome the problem you're indicating is by using group-url.
a URL is bound to a specific tunnel-group and allows you to land directly on the one you desire.
vide:
http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/98580-enable-group-dropdown.html
M. -
NAC-L2-802.1x (EAP-FAST) and Cisco Secure Services Client 5.0 in wired net
Hi!
(Sorry, if this is a wrong forum.)
Does anybody have any success with Cisco SSC and EAP-FAST in the wired network?
I'm going to use NAC, so I'm trying to set up EAP-FAST. I see the pop-up window on the client to enter user credentials and I see a lot of "debug radius" messages on my 3750 12.2(44)SE switch:
Access-Requests with User-Name="anonymous"
Access-Challenges (I see certificate is sent from ACS)
Access-Reject
CS ACS Failed Attempts Report shows "ACS user unknown" failure for "anonymous".
So far as I understood, EAP-FAST is a tunneled method and it uses "anonymous" to protect user's identity during phase 0 / phase 1 transactions. The actual username is sent in phase 2 transaction.
The following is excerpt from the CS ACS documentation:
"EAP-FAST can protect the username in all EAP-FAST transactions. ACS does not perform user authentication based on a username that is presented in phase one; however, whether the username is protected during phase one depends on the end-user client. If the end-user client does not send the real username in phase one, the username is protected. The Cisco Aironet EAP-FAST client protects the username in phase one by sending FAST_MAC address in place of the username. After phase one of EAP-FAST, all data is encrypted, including username information that is usually sent in clear text."
SSC 5.0 is indeed set up with "Unprotected Identity Pattern"=anonymous and "Protected Identity Pattern"=[username] using sscManagementUtility.exe
So, the question is: Why is ACS 4.1 trying to authenticate username "anonymous" if it knows that the user is fake? Does anybody have working configuaration for EAP-FAST in a wired network?
Any help is greatly appreciated.Correct, ACS database wasn't selected on the NAP Authentication page. It works now, but I constantly get the following message in the Windows event log: "The Cisco Secure Services Client service hung on starting". This is Windows 2000 Advanced Server system with SP4. SSC was set up with no domain authentication, no machine authentication, single sign-on. After some time the SSC service starts, but at that time my PC is already put into the guest VLAN by the switch (the tx-period is 10 seconds):
POD1-SW#sh run int fa1/0/1
Building configuration...
Current configuration : 378 bytes
interface FastEthernet1/0/1
switchport access vlan 999
switchport mode access
dot1x mac-auth-bypass
dot1x pae authenticator
dot1x port-control auto
dot1x timeout reauth-period server
dot1x timeout tx-period 10
dot1x reauthentication
dot1x critical
dot1x critical recovery action reinitialize
dot1x guest-vlan 91
dot1x critical vlan 11
spanning-tree portfast
end
After all the VLAN is reassigned by the switch, but the delay is too high. How can I troubleshoot this?
Thx. -
Cisco IP 7960 and Cisco Router 2611....
Greetings,
I currently have 2 IP phones and a 2611 series router running 2600-ik902s2-mz.122-15.t5 IOS... Can anyone point me in the right direction on where/or how to start building a mini voice network? Any links, tutorials, info, advice would be greatly appreciated.
Thanks,
GabeHi
The best thing to setup a mini voip network would be to use the ITS solution where your IP phones will register directly with the 2611 router. The 2611 would act as a mini call manager where these ip phones talk to the router through skinny protocol and your outgoing calls can still go out through your FXO or digital port to the PSTN.
I would suggest to review the following doc. It is fairly complete.
http://www.cisco.com/en/US/products/sw/iosswrel/ps1839/products_feature_guide_book09186a008017fd13.html
If you dont have voice mail, you dont have to worry about that. The above URL is for ITS version 2.1. If you want to run the lates ITS version (3.0) you would need 12.2.15ZJ1 IOS on the router and the information can be found at:
http://www.cisco.com/en/US/products/sw/iosswrel/ps5012/products_feature_guide_book09186a00801812e4.html
Hope that helps. -
Oracle OVM 3.1.1 with Cisco 4948 - link aggregation ?
I have two Dell R710's in a lab that I am attempting to create a 2 node OVM cluster.
I am specifically looking for assistance with the Cisco etherchannel setup and OVM bonding on the interfaces.
I have configured bonding with Cisco and VMWare many times, I am looking for assistance with OVM.
A document, an email or any information I would gladly accept.
Thanks.I actually was wrong. I am running 2960s. We considered 4948s but opt for the 2900 series. Should be similar if not identical as far as lacp is concerned.
lacp is a option for ether channels. As well as pagp. Portchannels are by default lacp.
Oracle VM can use LACP and is not compatible with pagp. At least not that I know of.
Below is an example of the traffic on a working lacp link.
Channel group: 1
Gi1/0/35 13087824 405144 0 0 0 0 0
Gi1/0/36 13088080 405143 0 0 0 0 0
Nice and even :)
My portchannel groups include only layer 2 ports. They can contain either layer 2 or 3 ports. I'm just using layer 2 ports.
Not using vlan tagging. The native vlan tagging command assumes untagged traffic received is for "native vlan".
Oracle VM does have the ability to do vlan tagging but I do not use it and its a little tricky to setup on the default bond0. Been a little while since I considered it. Hope this makes sense. -
When I migrate CLOB datas from Oracle 10g to PostgreSQL 9.0,and the target data type is text,the replicat process abend,and it reports as following:
WARNING OGG-03056 Oracle GoldenGate Delivery, repdb2.prm: Source table SDCMNET.T_INFO_SUPERIOR_PROGRAM column PRO_CONTENT_CLOB data size exceeds the maximum target table sdcmnet.t_info_superior_program column pro_content_clob size. Automatic truncation is enabled for all tables/columns without further warnings.
WARNING OGG-00869 Oracle GoldenGate Delivery, repdb2.prm: [SQL error 0 (0x0)][Oracle][ODBC PostgreSQL Wire Protocol driver]String data, right truncated.
WARNING OGG-01004 Oracle GoldenGate Delivery, repdb2.prm: Aborted grouped transaction on 'sdcmnet.t_info_superior_program', Database error 0 ([SQL error 0 (0x0)][Oracle][ODBC PostgreSQL Wire Protocol driver]String data, right truncated.
But,according to the SEQNO and RBA,I find the records have been migrated,and the length of records is equal to what is in oracle.Then I try to use the odbc driver of postgresql 9.3 to replace,although I can login the database ,but it warns again.
Can anyone help me?This forum is for Oracle Maven Repository. You might have more luck posting your question in an forum for GoldenGate - you are more likely to find someone who knows about that product in its own forums.
Maybe you are looking for
-
ITunes deleted all my apps after I clicked "Cancel" to sync apps
I'm at work and I wanted to do some serious app re-arranging. Rather than doing it manually on my iPhone5, I luanched iTunes. Note: I do *not* sync my iPhone with my work computer, but I thought maybe it could still rearrange the apps since I can s
-
Can't pass event from WebDynPro to JspDynPage - why?
I Created JSP project and embedded in main page script (in its title), which subscribes to event by EPCM API, EPCM.subscribeEvent("urn:ru.intertech.common.wd.component", "save", go); and created WebDynPro page that fires event using, when pressing
-
What is the best approach for different roles to be able to access relevant content
I am working on a project with the following requirements: - - a calendar, FAQ list, downloads document library and Service Request log developed from a custom list - I have three roles - employee, line manager and Senior Executive - For each of the
-
Using Personal LaserWriter 300 w/eMac, OS X 2
Did anyone ever come up with a driver to allow a PLW 300 to work with Mac OS X? Along with the appropriate serial to USB adapter, I'm assuming. My one last query before I bite the bullet and buy a cheap Brother model, I guess....thanks for any help..
-
Hello! I deleted the recovery partition for getting more hard disk space... now I want it back. Is there any way? Maybe there's recovery DVD, but I've seen only 620 recovery DVD. Can I get help in a hp service center? Please help