T30 freezing issues and Touchpad & Trackpoint buttons not working.

Firstly I'll explain the freezing issue (this is now the 3rd time I've typed this, as the first two times my laptop froze before I finished!)
I run my laptop with the battery at 100% and plugged in and that's fine; as is running it on battery. The problem arises when my battery is low and I plug it into recharge. Soon after it's running on a/c the screen will go black and only way to shut down is by holding the power button. If I try to restart it too soon, the indicator lights next to the power button will illuminate, but the screen will stay black. Usually after 5-10 minutes it'll boot to the IBM screen & boot the rest of the way, but not too long into normal operation it'll go black again (sometimes hitting ctrl/alt/del will bring the screen back but it would be very distorted (pixilized) and would go black again and reboot. What could be causing these problems while recharging the battery? I've tried this with a couple different batteries (both OEM IBM) and it does it with both.
 Secondly, both left and right "mouse" buttons are now nonfunctional (though the middle button of the track points works.) I have the latest version of Ultranav Wizard and all the buttons are enabled. The touch pad and trackpoint ball work fine, just the 2 left and 2 right buttons do not. What could be the culprit for this issue? Luckily I have a usb mouse so that's what I'm using for the time being.
Message Edited by GoalieFergy53 on 02-14-2009 02:30 PM

My T42p Touchpad and Trackpoint work fine however,
the buttons are not responding properly.
I'm forced to use an optical mouse to properly maneuver when working on
the screen.
When the well is dry, we'll all know the value of water.

Similar Messages

  • HT4623 Anyone having trouble with App Store install and cloud store buttons not working after 6.1 update?

    Anyone having trouble with App Store install and cloud store buttons not working after 6.1 update? I go to install an app. I hit install and nothing happens. About a minute later it asks me for my password and then it does nothing. The install button goes back to saying install. However the app shows up in my installed list and in cloud but no app installed.

    OK - I found a helpful post - closed app store app and under Settings/General/Date and Time I reset the date and time by switching off "Set Automatically" and then switching it on again. Went back to App Store, launched it and Updatesseems to be working again.
    Go figure? Logical, No!

  • Myi iphone4  microphone not working and the home button not work after IOS6 updat

    Myi iphone4  microphone not working and the home button not work after IOS6 updat

    Did you try another restore and this time not to restore from a backup and see if that makes a difference? This is what Apple would tell you to do next based on my iphone 5 fiasco.
    Make sure all your data is available on your computer for manual syncing later.
    Since you did the hard reset I assume that means your home button isn't broken only that it got frozen before. Were you able to get the Apple logo after the reset? Did it boot?
    And you are using iTunes 10.7?
    I'm just trying to help get you going.

  • My IPhone 4s is freezing up and the wifi will not work. This happened after the update. I have tried to restore it and that did not fix it. Any suggestions?

    My IPhone 4s is freezing up and the wifi will not work. This happened after the update. I have tried to restore it and that did not fix it. Any suggestions?

    Most of your purchases content can be downloaded again via the Purchased tabs in each of the store. I realize that this will be a problem for the iTunes Store on the iPad, but that has nothing to do with apps, since apps are in the App Store.
    If you backed up synced with iTunes before you restored the iPad, your content should be in iTunes on your Mac and you should be able to sync it back again.

  • ★URGENT★ BLACKBERRY TORCH KEYBOARD TRACKPAD AND ALL OTHER BUTTONS NOT WORKING 9810

    MY BLACKBERRY TORCH 9810 KEYBOARD AND CALL,ETC BUTTONS STOPPED WORKING.
    My blackberry got ink at the top of the phone so I got a lightly wet tissue and cleaned the top part of the phone after I finished cleaning it, I recognised the keyboard stopped working. The touch screen still works but the physical keyboard and all other buttons have stopped working. Please help me, I really ened that phone for emergency uses, etc. I do not want to restore my phone so do not suggest that solution.
    UPDATE: Right now I have my phone inside a bowl of uncooked rice. 
    UPDATE 2: 30 minutes later, I took the phone and rebooted it the keyboard still does NOT work but the trackpad can move up and down but when pressing it does nothing.
    PLEASE HELP NEED URGENT HELP.

    Hi and Welcome to the Community!
    30 minutes is not enough...follow EXACTLY the instructions in this FAQ:
    http://www.blackberryfaq.com/index.php/Got_Your_BlackBerry_Wet%3F
    Also, prepare yourself for the worst...the only thing that is predictable about moisture intrusion into a BB is that the results will be unpredictable. Since you have already re-applied power to the BB too soon, it is much more likely that you have totally fried something inside.
    Good luck!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Lock button and lower volume button not working.

    Any advice if a button stops working? I don't know why either

    Did you try resetting/rebooting the iPad by holding down on the lock and home buttons at the same time until the Apple Logo appears on the screen. I realize that involves using the lock/sleep button, but if it is a software issue, it might help. Give it a try.
    Without knowing more about the problem, your next step might be resetting all settings and then restore the iOS software after that. If those fail to help, then a trip to an Apple Store should be the next step for you.
    It could be a hardware issue and since both buttons are on the right side of the iPad, there might be some connection between the two buttons that is causing the problem.

  • [T440p] TrackPoint buttons not working

    Hi,
    I have a weird problem with my T440p's TrackPoint (running Windows 7 Pro, x86) using out-of-the-box settings. Basically, it seems that its buttons do not work at all - the designated upper regions of the TouchPad (which should supposedly function as TrackPoint dedicated buttons) produce no effect upon clicking. Also, if I disable the TouchPad in the Mouse control panel module (ThinkPad tab), I can no longer click anything and have to resort to keyboard navigation to restore mouse functionality.
    What is interesting is that this is the second T440p unit I have tried to use the TrackPoint on and failed. The first one was also running Windows 7, but had a different screen (HD+, while the current one is Full HD) and CPU (2-core i5 vs. current 4-core i7).
    How do I use the TrackPoint buttons, again? Cause it's obvious by now that it does not work the same way as on my trusty X220 machine...
    Solved!
    Go to Solution.

    FOLLOW UP;
    when ultranav driver is installed then i do not seem to have issues with the trackpoint movements, until I start clicking buttons. For example this is a standard event. I am in window , like in  a multipage word document, and i want to scroll down using the slider on the left frame of the window. If I do it by keeping the button pressed and moving the trackpoint - all works fine; but if I want to do it by simply multiple clicks at the bottom part of that slider part of windoe frame (left frame) then after 3 clicks (always ) the track point and buttns freeze forever, or sometimg can be unfreezed by external mouse movements, or by quikcly moving my hand over the touchpad...
    As if quick succession of button clicks created the problem
    When no ultranav driver is installed (and touch pad disabled in BIOS) then occasionally the button do not work and in general harder clicks are needed, and occasionally succesion of clicks also freezes the track point and buttons...some time can be "woken up" by external mouse movements and sometimes not.
    thanks for any help or pointing to a place on www where I can find solution..
    by the way anybody heard of physically putting the old trakcpoint system (like e.g. in T60) to t440. ???

  • Hp DV6 TouchPad Lock Button Not Working Please Help.?

    I just bought my hp dv6 6c4se entertainment notebook. but the touchpad on and off button is not working.please help.yes there is a little white sqaure in the left up corner of the touchpad.but it doesnt work.please help somebody

    Try a Hard Reset to gently "kick" that TouchPad back into operation.
    HP Notebook PCs - Use a Forced Reset to Resolve Hardware and Software Issues on Notebook with a Seal...
    Removable Battery:
    HP Notebook PCs - Use Hard Reset to Resolve Hardware and Software Issues
    Kind Regards,
    Dragon-Fur

  • ThinkPad USB Keyboard with TrackPoint -- Buttons not working (SK-8833)

    The buttons on my trusty Thinkpad USB external keyboard (SK-8855) have suddenly stopped working properly. The right-hand button has ceased functioning most of the time, and now the middle button both scrolls windows (as it is supposed to) but also acts as the right-hand button (showing context menus, etc.). Also, occasionally, the left button stops working too, until I click on the center button, and then it will work fine for a while. There is no real consistency except that they are inconsistent.
    The rest of the keyboard, including the trackpoint, works fine, but the fault happens when the keyboard is plugged into two different machines--my Thinkpad T430 and my Thinkpad x100e (the very first time it was ever plugged into this one).
    I would be happy to see if some dirt has clogged up the button mechanism, but the keyboard is still under warranty and one of the screws is under a label (I think). It looks like some kind of hardware issue since I haven't changed any software on my system, but I guess it could be a driver problem, but Lenovo has made it all but impossible to find the drivers of this keyboard.
    Does anyone have any ideas, or should I just be contacting support for a warranty repair?

    You should get the keyboard changed under warranty.
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • Touchpad Scroll-buttons not working properly

    Hello all,
    I was not sure if this is actually a Desktop Environment or Hardware problem, but since it's hardware related I will post it here.
    The problem:
    On my touchpad (on Acer Aspire 5610Z) I have scroll button for up/down/left/right and until a recent update the scroll buttons need to be clicked repeatably in order to scroll. Before the upgrade and the way I'm expecting to behave is that when I click and hold a button - it should repeat the scroll (I hope you are able to understand it). So basically my problem is that to scroll with the scroll-buttons I have to click it numerous times in order to scroll, instead of just holding the button pressed.
    At the same time all other features like two-finger scrolling, gestures etc. are working, but I'm not used to scroll with two fingers and would like to have my scroll-buttons working.
    Here is some information about the configuration:
    10-synaptics.conf
    Section "InputClass"
    Identifier "touchpad catchall"
    Driver "synaptics"
    Option "SHMConfig" "on"
    MatchIsTouchpad "on"
    MatchDevicePath "/dev/input/event*"
    Option "TapButton1" "1"
    Option "TapButton2" "2"
    Option "TapButton3" "3"
    Option "VertEdgeScroll" "on" # enable vertical scroll zone
    Option "HorizEdgeScroll" "on" # enable horizontal scroll zone
    Option "VertTwoFingerScroll" "on" # vertical scroll anywhere with two fingers
    Option "HorizTwoFingerScroll" "on" # horizontal scroll anywhere with two fingers
    EndSection
    Output of synclient -l
    Parameter settings:
    LeftEdge = 1752
    RightEdge = 5192
    TopEdge = 1620
    BottomEdge = 4236
    FingerLow = 25
    FingerHigh = 30
    FingerPress = 256
    MaxTapTime = 180
    MaxTapMove = 221
    MaxDoubleTapTime = 180
    SingleTapTimeout = 180
    ClickTime = 100
    FastTaps = 0
    EmulateMidButtonTime = 75
    EmulateTwoFingerMinZ = 282
    EmulateTwoFingerMinW = 7
    VertScrollDelta = 100
    HorizScrollDelta = 100
    VertEdgeScroll = 1
    HorizEdgeScroll = 1
    CornerCoasting = 1
    VertTwoFingerScroll = 1
    HorizTwoFingerScroll = 1
    MinSpeed = 1.6
    MaxSpeed = 1.75
    AccelFactor = 0.087
    TrackstickSpeed = 40
    EdgeMotionMinZ = 30
    EdgeMotionMaxZ = 160
    EdgeMotionMinSpeed = 1
    EdgeMotionMaxSpeed = 401
    EdgeMotionUseAlways = 0
    UpDownScrolling = 1
    LeftRightScrolling = 1
    UpDownScrollRepeat = 1
    LeftRightScrollRepeat = 1
    ScrollButtonRepeat = 100
    TouchpadOff = 0
    LockedDrags = 0
    LockedDragTimeout = 5000
    RTCornerButton = 0
    RBCornerButton = 0
    LTCornerButton = 0
    LBCornerButton = 0
    TapButton1 = 1
    TapButton2 = 2
    TapButton3 = 3
    ClickFinger1 = 1
    ClickFinger2 = 1
    ClickFinger3 = 1
    CircularScrolling = 0
    CircScrollDelta = 0.100007
    CircScrollTrigger = 0
    CircularPad = 0
    PalmDetect = 0
    PalmMinWidth = 10
    PalmMinZ = 200
    CoastingSpeed = 20
    CoastingFriction = 50
    PressureMotionMinZ = 30
    PressureMotionMaxZ = 160
    PressureMotionMinFactor = 1
    PressureMotionMaxFactor = 1
    GrabEventDevice = 1
    TapAndDragGesture = 1
    AreaLeftEdge = 0
    AreaRightEdge = 0
    AreaTopEdge = 0
    AreaBottomEdge = 0
    HorizHysteresis = 25
    VertHysteresis = 25
    ClickPad = 0
    Output of xinput list :
    ⎡ Virtual core pointer id=2 [master pointer (3)]
    ⎜ ↳ Virtual core XTEST pointer id=4 [slave pointer (2)]
    ⎜ ↳ SynPS/2 Synaptics TouchPad id=12 [slave pointer (2)]
    ⎣ Virtual core keyboard id=3 [master keyboard (2)]
    ↳ Virtual core XTEST keyboard id=5 [slave keyboard (3)]
    ↳ Power Button id=6 [slave keyboard (3)]
    ↳ Video Bus id=7 [slave keyboard (3)]
    ↳ Power Button id=8 [slave keyboard (3)]
    ↳ Sleep Button id=9 [slave keyboard (3)]
    ↳ USB2.0 Camera id=10 [slave keyboard (3)]
    ↳ AT Translated Set 2 keyboard id=11 [slave keyboard (3)]
    And the last upgrade since the scroll buttons stopped working:
    [2012-03-14 08:15] upgraded chromium (17.0.963.78-1 -> 17.0.963.79-1)
    [2012-03-14 08:15] > Updating desktop mime database...
    [2012-03-14 08:15] upgraded eric (5.1.8-1 -> 5.2.0-1)
    [2012-03-14 08:15] upgraded freetype2 (2.4.8-1 -> 2.4.9-1)
    [2012-03-14 08:15] upgraded git (1.7.9.3-1 -> 1.7.9.4-1)
    [2012-03-14 08:15] upgraded glproto (1.4.14-1 -> 1.4.15-1)
    [2012-03-14 08:15] upgraded grep (2.11-1 -> 2.11-2)
    [2012-03-14 08:15] upgraded gstreamer0.10 (0.10.35-1 -> 0.10.36-1)
    [2012-03-14 08:15] upgraded gstreamer0.10-base (0.10.35-1 -> 0.10.36-1)
    [2012-03-14 08:15] upgraded gstreamer0.10-base-plugins (0.10.35-1 -> 0.10.36-1)
    [2012-03-14 08:15] upgraded gstreamer0.10-good (0.10.30-2 -> 0.10.31-1)
    [2012-03-14 08:15] upgraded gstreamer0.10-good-plugins (0.10.30-2 -> 0.10.31-1)
    [2012-03-14 08:15] upgraded xcb-proto (1.6-2 -> 1.7-2)
    [2012-03-14 08:15] upgraded libxcb (1.7-2 -> 1.8.1-1)
    [2012-03-14 08:15] upgraded libx11 (1.4.4-1 -> 1.4.99.1-1)
    [2012-03-14 08:15] upgraded libxt (1.1.2-1 -> 1.1.2-2)
    [2012-03-14 08:15] upgraded imagemagick (6.7.5.3-1 -> 6.7.6.0-1)
    [2012-03-14 08:15] upgraded inputproto (2.0.2-1 -> 2.2-1)
    [2012-03-14 08:15] upgraded libglapi (7.11.2-1 -> 8.0.1-2)
    [2012-03-14 08:15] upgraded libgl (7.11.2-1 -> 8.0.1-2)
    [2012-03-14 08:15] upgraded intel-dri (7.11.2-1 -> 8.0.1-2)
    [2012-03-14 08:16] upgraded kdebase-runtime (4.8.1-1 -> 4.8.1-2)
    [2012-03-14 08:16] upgraded khrplatform-devel (7.11.2-1 -> 8.0.1-2)
    [2012-03-14 08:16] upgraded libegl (7.11.2-1 -> 8.0.1-2)
    [2012-03-14 08:16] upgraded libgles (7.11.2-1 -> 8.0.1-2)
    [2012-03-14 08:16] Users no longer need to be in the 'camera' group to use camera devices
    [2012-03-14 08:16] upgraded libgphoto2 (2.4.11-1 -> 2.4.13-1)
    [2012-03-14 08:16] upgraded libnids (1.24-1 -> 1.24-2)
    [2012-03-14 08:16] upgraded libpciaccess (0.12.1-1 -> 0.13-1)
    [2012-03-14 08:16] upgraded libtiff (4.0.0-1 -> 4.0.1-1)
    [2012-03-14 08:16] upgraded libxft (2.3.0-1 -> 2.3.0-2)
    [2012-03-14 08:16] upgraded libxi (1.4.5-1 -> 1.6.0-1)
    [2012-03-14 08:16] upgraded man-pages (3.36-1 -> 3.37-1)
    [2012-03-14 08:16] upgraded mesa (7.11.2-1 -> 8.0.1-2)
    [2012-03-14 08:16] upgraded mpfr (3.1.0.p3-1 -> 3.1.0.p7-1)
    [2012-03-14 08:16] upgraded oxygen-gtk2 (1.2.1-1 -> 1.2.2-1)
    [2012-03-14 08:16] upgraded oxygen-gtk3 (1.0.1-1 -> 1.0.2-1)
    [2012-03-14 08:16] upgraded poppler (0.18.3-2 -> 0.18.4-1)
    [2012-03-14 08:16] upgraded poppler-glib (0.18.3-2 -> 0.18.4-1)
    [2012-03-14 08:16] upgraded poppler-qt (0.18.3-2 -> 0.18.4-1)
    [2012-03-14 08:16] upgraded python-configobj (4.7.2-3 -> 4.7.2-4)
    [2012-03-14 08:16] upgraded python-pygments (1.4-5 -> 1.5-1)
    [2012-03-14 08:16] upgraded python2-pygments (1.4-5 -> 1.5-1)
    [2012-03-14 08:16] upgraded ruby (1.9.3_p125-1 -> 1.9.3_p125-2)
    [2012-03-14 08:16] upgraded skype (2.2.0.35-2 -> 2.2.0.35-3)
    [2012-03-14 08:16] upgraded xf86-input-evdev (2.6.0-4 -> 2.7.0-1)
    [2012-03-14 08:16] upgraded xf86-input-synaptics (1.5.0-1 -> 1.5.99-0.2)
    [2012-03-14 08:16] upgraded xf86-input-vmmouse (12.7.0-3 -> 12.8.0-1)
    [2012-03-14 08:16] upgraded xf86-video-intel (2.17.0-2 -> 2.18.0-1)
    [2012-03-14 08:16] upgraded xf86-video-vmware (11.1.0-1 -> 12.0.0-1)
    [2012-03-14 08:16] upgraded xorg-server-common (1.11.4-1 -> 1.12.0-1)
    [2012-03-14 08:16] upgraded xorg-server (1.11.4-1 -> 1.12.0-1)
    [2012-03-14 08:16] upgraded xorg-xinput (1.5.3-2 -> 1.5.99.1-1)
    [2012-03-14 10:51] Running 'pacman -S gimp-devel'
    [2012-03-14 10:52] Running 'pacman -S extra/gimp-devel'
    [2012-03-14 10:52] Running 'pacman -Syy'
    [2012-03-14 10:52] synchronizing package lists
    [2012-03-14 10:54] Running 'pacman -S extra/gimp-devel'
    [2012-03-14 10:55] Updating font cache... done.
    [2012-03-14 10:55] installed gsfonts (1.0.7pre44-3)
    [2012-03-14 10:55] installed libwmf (0.2.8.4-9)
    [2012-03-14 10:55] installed babl (0.1.6-1)
    [2012-03-14 10:55] installed gegl (0.1.8-2)
    [2012-03-14 10:55] installed gimp-devel (2.7.5-1)
    [2012-03-14 11:01] Running 'pacman -U /tmp/yaourt-tmp-vladi/PKGDEST.26J/gimp-photoshop-brush-1.0-1-i686.pkg.tar.xz'
    [2012-03-14 11:02] installed gimp-photoshop-brush (1.0-1)
    [2012-03-14 11:02] Running 'pacman -U /tmp/yaourt-tmp-vladi/PKGDEST.Jc0/gimp-photoshop-brush-1.0-1-i686.pkg.tar.xz'
    [2012-03-14 11:02] upgraded gimp-photoshop-brush (1.0-1 -> 1.0-1)
    [2012-03-14 11:03] Running 'pacman -S --asdeps --needed extra/perl-xml-parser extra/intltool'
    [2012-03-14 11:03] installed perl-xml-parser (2.41-2)
    [2012-03-14 11:03] installed intltool (0.50.1-1)
    [2012-03-14 11:03] Running 'pacman -U /tmp/yaourt-tmp-vladi/PKGDEST.GVM/gimp-plugin-saveforweb-0.29.3-1-i686.pkg.tar.xz'
    [2012-03-14 11:03] installed gimp-plugin-saveforweb (0.29.3-1)
    [2012-03-14 11:04] Running 'pacman -U /tmp/yaourt-tmp-vladi/PKGDEST.OX1/gimpfx-foundry-2.6_1-2-i686.pkg.tar.xz'
    [2012-03-14 11:04] installed gimpfx-foundry (2.6_1-2)
    [2012-03-14 20:27] Running 'pacman -Syy'
    [2012-03-14 20:27] synchronizing package lists
    [2012-03-14 20:30] Running 'pacman -Syu'
    [2012-03-14 20:30] synchronizing package lists
    I thank you in advance for your suggestions

    I'm afraid the problem is in driver.
    I compared sources of input-synaptics 1.6.3 and 1.7.0 and it seems that author has cut off the functionality of "repeating" scrollbuttons
    Here's the announce of this new version:
    http://lists.freedesktop.org/archives/x … 55593.html
    And we can read there: "Purge scrollbuttons (repeat)".
    Strange decision I think...

  • Mute button, low volume button and high volume button not working after upgrade to Win7 Pro

    Hi all, Im using X301. Previously it was shipped with the Vista Business. I was entitled for free upgrade to Win7 since the thinkpad was bought after 25th of June 09. The problem started after I successfully upgraded my Vista to Win7 Pro. My Mute/Unmute button was consistently in amber colour (signal for disabled). the volume button also is not working anymore. On the system side, everything was fine. the drivers is working properly.. the windows also is showing the volume is in a good shape. Unfortunately the button on the thinkpad is always on the disabled mode. Ive been searching for a related drivers that i could download and solve the issue. but till now all the softwares and drivers downloaded from lenovo could not solve my problem. any suggestion or comment is highly appreciated. thanks a million

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:       
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    -  Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar
    When iOS 6.1 comes out I would update.

  • Website payment and shopping cart buttons not working on Windows Phone browser

    A customer shopping on our site notified me that the "add to cart" and "view cart" buttons were taking him to the PayPal main site and not the shopping cart. I tried a Windows Phone at the Verizon store and found the same issue. I have tested the site on multiple Windows desktop browsers, on Android, Linux and iPad and have never seen this issue.  What is going on with IE on Windows Phone?

    I had this problem too, but I found a post burried on the web that said to add " p06- "  (without quotes) before the imap and smpt server names and that worked:
    p06-imap.mail.me.com
    p06-smtp.mail.me.com
    Everything stays checked, SSL for both, authentication and use same username and password checked.

  • Program and Source Monitor buttons not working?

    I need to take a screen capture of my project, but NONE of the Program monitor buttons are working. I click them and it doesn't do anything.
    I'm posting this because none of the suggestions in the other discussions helped me at all.
    Screen Capture worked perfectly when I used it YESTERDAY. Aside from closing the program, I can't find any other changes that have been made to either my computer or PP_CC.
    I have already tried:
    -Reloading PP_CC
    -Restarting my computer
    -Resetting my preferences (Held SHIFT while opening the program)
    -Changing projects and timelines
    -Adding and removing buttons to see if that did anything
    I'm at a complete loss....
    Is there a way to take a screenshot in the meantime while I figure out what's going on with this issue?
    Working on Windows 7 64bit system

    Hi,
    This might help :
    Go to Documents > Adobe > Premiere Pro and rename the 8.0 folder to 'old8.0' and then launch Premiere.
    8.0 is Premiere CC 2014
    7.0 is Premiere CC
    Rename the respective folder.
    Note: By doing this you will lose your customised keyboard shortcuts and custom workspaces.
    Report back if it helps.
    Thanks,
    Rameez

  • Fn shortcuts and blue thinkvantage button not working

    The Fn+F2, Fn+F5, and Fn+F8 shortcuts are not working on my computer, yet the Fn+F3 and Fn+F4 shortcuts are working. The other ones used work as well but now aren't and I'm not sure why. They blue Thinkvantage button up by the volume also used to work and is no longer working as well. Any ideas as to how I get them to work again?

    I thought this was the one place I could rely on for answers, but I guess not. I have given up hope.
    T400
    Intel® Core™2 Duo T9400 2.53 GHz__Windows 7 Professional__3GB Memory__160GB, 7200RPM Hard Drive__14.1” WXGA+TFT-CFL__ATI Mobility Radeon™ HD 3470--

  • Captivate 3 - Continue and Review Quiz Button Not Working

    I have just published a SCORM course in Captivate. It works perfectly fine once I've uploaded it into the LMS except one small part. I've set up the quiz so each learner is required to pass the quiz in order to complete the module. At the end of the quiz, the results page appears with two buttons (Continue and Review Quiz). Those buttons don't work.
    I set up the quiz so that learners have 2 attempts to successfully complete it. If they're unsuccesful, the continue button should direct them to the beginning of the quiz so they could retake it. If they have successfully complete, the continue button should take them to the next slide. That's not working. For some reason, the continue button only works if the learner has failed the quiz. The Review Quiz button also doesn't work. I did select the option allowing them to do so. Can someone please help?

    Hi there
    Please send me a private E-Mail message to rstone75 (at) kc (dot) rr (dot) com and advise of the exact file name of the file you are linking to.
    I'll send you back a file that you can use to test and see if the link works.
    Cheers... Rick
    Helpful and Handy Links
    Captivate Wish Form/Bug Reporting Form
    Adobe Certified Captivate Training
    SorcerStone Blog
    Captivate eBooks

Maybe you are looking for