T400 with ATI Radeon HD 3400. Driver not found after running ImageX.exe /Capture

Hello,
I was able to reproduce the following problem on a T400.
- unattended installation of WXP-SP3 (slipstreamed)
- reboot
- install latest ATI driver from Lenovo/IBM site (8.503.2.2-080818a-069536C)
- reboot
At this point, the video driver is well configured.
- Reboot once or twice, video driver still good.
- Boot the T400 on WinPE 2.0
- Capture the C:\ to a network file share using ImageX.exe (from Microsoft's WAIK 1.1)
- Shutdown the T400, and reboot on C:\
- At this point, video driver is "lost". The Hardware Wizard says "new driver found", but stick with default VGA.
Then I get an ATI error telling the driver is missing or not well installed.
- When rebooting several times, suddenly the card is back in the device manager as a Radeon HD 3400.
(without re-installing the driver ...)
Anyone has an explanation ?
Please not I did not run "sysprep.exe" before capturing with ImageX.exe
stefan

Update on this problem.
After running "sysprep.exe -mini -quiet -reseal -shutdown", I ran the "ImageX.exe /capture".
After rebooting the T400, the ATI driver was fine.
Either is a coincidence (but I could repeat it 3 times...) or it is not advised to run "ImageX.exe /Capture" on a non-syspreped Windows XP.
I know that a non-syspreped Vista system has a limitation if captured with ImageX.exe. But I am not aware on any limitation with XP.
Stefan

Similar Messages

PPC G5 with ATI Radeon 9600 Pro monitors not getting signal

hi there.
I have a PPC G5 with ATI Radeon 9600 Pro graphics card and I cannot get a monitor to work properly. I am trying an old Apple Studio Display (circa 2001) and a Viewsonic VA520.
It seems like the Apple display should work, but all I get is a black screen. I ran it through a DVI to ADC adapter and had it working for a short period of time, but for some unknown reason it went back to the black screen.
The Viewsonic gives a 'NO SIGNAL' screen and not much else.
Both of these monitors have worked on other G5's. I am guessing this is a graphics card issue.
I appreciate any kind or helpful words! Thank you.

I'm having a similar problem with the G5 not recognizing a VGA monitor on either video out. I have no problem using two monitors with the DVI inputs but I need to use a VGA video splitter for a third screen. It worked at the beginning of this week, and now it refuses any VGA out, even without the splitter, just going into directly into the VGA in of one of my working monitors via a DVI-VGA adapter(i've tried different ones). I read another post about trashing "displays" and "windowserver" preference files but i haven't yet tried that..any clues??

Graphic Corruption with ATI Radeon Open Source Driver

Hello!
Using the latest "radeon" driver from the Arch repo I get weird blue stripes moving diagonally all across the screen as soon as the driver is loaded. KMS is on, without KMS I get no graphical issues.
I'm a former Catalyst user, fglrx is disabled and xorg.conf is deleted.
GPU: ATI Radeon HD4570
Any ideas?
Last edited by CHPE (2011-04-12 18:21:41)

I seem to have no problems at all with kernel versions <= 2.6.37-5. Seems to be a problem with the newer kernels?

C:\lib not found after run asant

I found result that was C:\lib not found. After run asant build the exercise date and bookstore, I can see the result C:\lib not found in dos prompt.Why? What lib I need ? It worked for hello1 and hello3.I think I installed the javahome and j2ee home probably.If someone know,Could you show me the right way?
After I run like.. asant build.xml .. the result was build.xml file doesnt exit in this project.
Show me the right way pls.
Thanks

try specifying the j2ee.home explicitly in examples/common/build.properties:
for example:
j2ee.home=H:\Sun\\AppServer

Express Card Driver Not found after upgrade to 10.6.7

I upgraded my macbook pro to version 10.6.7 recently and later found out that the express card 34 slot drive was missing and could not access my Sony SxS cards. After some extensive search I found the site where I could retrieve the driver from. It is listed below. Worked for me! It should work for you also.
http://support.sonybiz.ca/esupport/Navigation.do?filetype=Drivers
SxS Device driver Ver. 1.0.52020 forMAc (Oct 2010)

Hi,
I need to configure a copier konica minolta 7145 with IP-432 on Mac OS X 10.6.7.
the copier has never been used before on this computer, can you tell me how to print with the Konica on mac, which drivers to install, what kind of cables and which procedure.
Thanks a lot!

Windows XP drive not found after install

After installing Windows XP on boot camp, I have found that the computer will restart and then fail to find the drive I have just installed windows on giving me an error message something like "Cannot locate boot disk". If i restart into OSX then it finds the drive but i cannot boot into windows because it will just display the error message. If i try installing Vista this works fine but Vista is shockingly awful and i would sooner have XP. Any ideas??

Evening all
Have you disabled any Norton, KAS, antivirus anti spyware programs?
Did you set a restore point prior to installing the Sp3?
Which method did you install the Sp3 from? full adminstrator account or apply the subinacl program and reset.cmd ?
There may be other problems prior to install of Sp3, Are the bios,of the systems you are using, the latest version?
What type of system are you using?
Are you using the latest W.H.Q.L. Microsoft signed drivers video available for your system? 174.74 from Nvidia, 8.4 catylst for ATI/AMD?
If you are using X2 processor both the processor driver and the dual core optimizer. You cannot depend on the Sp2 driver for proper operation.
What about chipset drivers?
And the mouse, and other perpherials?
If you have any unsigned drivers you will have endless reboots.
If you check the system to see if safe mode is available you can trouble shoot what is happening
*Press f8 prior to the Windows splash screen*
Log in as adminstrator *Full one*
If you are using an AMD machine, check the regedit for the following key
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Intelppm\Start
If this key exists change it to 04 Hexdecimal and reboot.
as seen here
http://forums.microsoft.com/TechNet/ShowPost.aspx?PostID=3072752&SiteID=17
If you are still having problems see follow the advice at the end of this posting and add what problems you are having. And send the logs after a MSFT team member responds with an address.

CD drive not found after installing Itunes

When I install Itunes on my computer - the computer can not find or open my CD drive at all. If I uninstall and reboot the CD drive shows up and operates. I have tried to reinstall, update drivers, etc with no luck. Any thoughts??

I have seen several other people with the same issue. The problem seems to be some level of incompatibility between the Gear Software CD/DVD filter driver used by iTunes and some CD/DVD drives under Vista. I too have a Dell with the same problem, but I'm not holding my breath for a fix. The only workaround I know of is to to remove the GearAspiWDM filter driver from the registry. If you do this and reboot, your DVD drive will show up again, and iTunes will work except for burning CDs or DVDs. ITunes will also complain about drivers being installed incorrectly whenever you open it.
Here's the registry key to remove:
HKEYLOCALMACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E965-E325-11CE-BFC1-08002BE1 0318}\UpperFilters=GearAspiWDM
I'm not sure whether the problem is with Vista, Gear Software, iTunes, or the Dell DVD drive firmware. But, getting all the parties working together to resolve this one will be next to impossible in my opinion.

USB drives not found after erasing them: iMac.

I had a couple of USB drives that showed empty but had almost zero capacity. I erased them via Utilities. Fine. (didn’t get to the part about emptying Trash….doh.
Now my iMac does not show the drives in Finder (although I get a reminder to eject msg when I remove it).
The drive is recognized on my Macbook.
So now I can’t use my memory sticks in my iMac.
How can I get the iMac to recognise the sticks?

Finder preferences not shown, but see attached. The stick is seen in finder and is mounted, but not in Devices.

MDD upgrade conflict with ATI Radeon 9800

does anyone out there have my specs; Sonnettech MDX Dual 1.6gh processor with ATI Radeon 9800 Pro VGA card? After installing the processor, i now get weird lines all over the screen at bootup and then i get a bunch of green speckles all over my desktop after the computer boots. i can work on my computer, but the screen images, speckles and other artifacts are annoying. i have dropped the hz to 66 and the screen resolution to 800x600 because higher resolutions would cause the computer to freeze. does anyone have any catalyst settings or ATI display panel suggestions ? i wish i could attach the pictures i took of the display.
Dual Power Mac G4 867 & Macbook Pro 2gig Mac OS X (10.4.9) FCP Studio 5.1.2

Well, i tried your idea, bought the iceberq5, installed it with ease and things just got worse. 1st, my MDD Dual 867 mac's AGP slot is right next to my fourth RAM slot. So with the Iceberq5 installed, i had to lose 512mb of RAM. it just wont fit. the new cooler cover the RAM slot. so instead of 2gigs of RAM, i'm down to 1.5. 2nd, with the icebeq5 on the ATI card, the door will not close. the iceberq runs into the case holding my DVD drives. After booting the computer up with the case open, the screen still loaded with the screen defects. I'm thinking I have a bad card, yet it worked when the Sonnettech dual processor upgrade was not installed. these weird color lines only occur with the sonnettech md/1.6 dual upgrade and the ATI 9800 Pro installed. I then used TechTool pro to scan and check my AGP card VRAM and it gave me an error. So here is my question, is there another powerful AGP card out there for my mac dual 867 that has a powerful fan on it that is also small enough to allow my case to close and for me to have all my RAM installed ? Thanks

Mac Pro 5.1 (Mid 2010) with Ati Radeon 5870, I can't install Maverick, don't support the graphic driver

I have a Mac Pro with Ati radeon hd 5870 1024 MB, after the first reboot in the installation of Maverick, the screen does strange things as if the driver does not support.

Hello pitin,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573
You can reset the Mac's parameter RAM and SMC.
Best of luck,
Mario

PE 13 crashes due to incompatible video driver detected. Running on Win 7 SP1 with ATI 540v video card/driver. Deleting bad driver file in adobe program data does not fix the problem, it simply replaces the text file and crashes again. My video driver

PE 13 crashes due to incompatible video driver detected. Running on Win 7 SP1 with ATI 540v video card/driver. Deleting bad driver file in adobe program data does not fix the problem, it simply replaces the text file and crashes again. My video driver is just fine. Any help out there?

rb
Your video card driver may be fine for something, but just not compatible with Premiere Elements 13/13.1.
For those with the display card error, the answers include
a. assure your video card/graphics card driver version is up to date according to the web site of the manufacturer of the card -
if necessary consider a driver roll back.
b. determine in Device Manager/Display Adapters if the computer is using 2 cards instead of 1
c. delete the BadDrivers.txt file
the rationale for that deletion is found in post 10 of the following older post...principle applies to 13 as well as 9.
Re: Premiere Elements 9 Tryout Serious Display Problem
Have you looked for computer ATI card settings that might be more compatible with Premiere Elements 13/13.1?
When is the program crashing - just opening a new project or rather crashing if editing a particular video format at the Timeline level?
ATR

[Athlon64] Anybody has any experience with ATI Radeon XPRESS 200P chip sets?

Anybody has any experience with ATI Radeon XPRESS 200P chip sets?
I am looking to purchase a computer for my wife who does not require major computing power. And looks like ATI is a cheaper option. Any recommendations?
Any info is greatly appreciated.

Quote from: dannol48 on 23-June-05, 02:25:47
The RS480M2-IL haa a CnQ option in Bios.
Installing the AMD driver and setting the Power Scheme to "Minimal Power Management" in Power Options is required to enable CnQ in XP.
Danno
Hello Danno ^^¿''
Well, I just bought the RS480M2-IL with a Venice 3000+ and 1 GB DDR, I've tested the Video onboard(all the newest drivers installed) with the 3DMARK 2001, and I just can get 3052 ptos...so .. please tell if you has made some time ...and how's your score?
Oh man please tell me...maybe I made a bad choise but I was specting something better from this Mobo!!!...
thanks and enjoy the time
PD: Another thing: my modo comes with the bios ver. 3.4 ...and have "The Normals falis" son I don't really know wich ver, could be better....cya..

Problem with ati radeon in 4530s

hi ....i have problem with ati radeon graphic in hp 4530s ....
when i install graphic driver apear black screen and i dont see anything ....
i change windows and load that properly but when install graphic driver black screen apear again..
driver download is corectly i download driver from hp this problom is not from driver..but i dont what's problem
Please Help Me....Thnx
Sorry my english language is weak...:manvery

Nimestä päätellen oletan että oot varmaan suomesta
Eli suomeksi sanottuna osnavi sanoo että ongelma voi johtua liian heikkotehoisesta virtalähteestä, sitä ei voi säätää tehokkaammaksi mistään biosista vaan jos se on alitehoinen pitää hommata uusi tehokkaampi virtalähde. Eli nuo arvot löytyy todennäköisesti sen virtalähteen kupeessa olevasta tarrasta. Se 12 volttia pitäisi olla vähintään 12 amppeeria että se riittäisi kunnolla radeonin näytönohjaimelle. Yleensä 300 wattinen poweri on riittävä, eli siinä tarrassa pitäisi olla maininta ainakin siitä kokonaistehosta, esim total output 300w tai jotain vastaavaa. Vika voi aivan hyvin olla jossain muuallakin, mutta yleensä täällä aina ensimmäiseksi syylliseksi arvellaan virtalähdettä, itselläni kyllä toisessa koneessa radeon 9200se näytönohjain toimii vaikka virtalähde on vain 200 wattinen. Niin ja muuten... eikö olisi helpompaa kysyä neuvoa ensin joltain suomenkieliseltä sivustolta

K7D Master-L with ATI Radeon 7000

Is anyone using K7D Master-L with ATI Radeon 7000? I am not able to use this
combination. When I switch on the power, the screen doesn't show antying. It is just
blank. Even though the monitor doesn't show up, if I don't press any key then the
system goes further till I see all the 4 leds as green and it tries to read from the
floppy drive. However, if I press a key after the keyboard is initialized, then the
d-bracket stops at Testing VGA BIOS. I haven't installed my hard drive at this stage.
MSI support asked me to try with another graphics card. They also suggested clearing
CMOS. I cleared the CMOS and the problem still exists. In addition, now the d-bracket
stops at "Initializing hard drive controller" though I didn't install hard drive. So, I went
ahead and installed my 200GB hard drive and no change. I think, to fix this issue, I
should first be able to fix my VGA issue. Also note that as I can't see the monitor from
the beginning, I don't know what my BIOS version is and if I can flash it with the latest
version.

I just tried with Creative Lab's "3D Blaster Savage4 32MB AGP (32MB SDRAM) " CT6900 which I borrowed from a friend. It didn't work either though this card is supposed to support AGP 2x/4x. I need to see what other cards I can get hold of
and try.
However, as I mentioned, initially the sequence was complete and I could see the 4 leds showing green. But after the advice from MSI tech support to try clearing CMOS for this problem, now the sequence stops at "Initiating Hard Drive Controller" (red red green green). Could this be because the BIOS doesn't know the HDD details after resetting CMOS? If so, once I get my VGA problem resolved will I be able to solve this problem
by entering into BIOS setup? At what stage does the BIOS setup screen show up when I press 'Del' key? If it is after the entire POST sequence then I will be stuck at the hard drive initialization. Also, I read that AMI BIOS supports Ins key which will bypass CMOS setup in the case. Does AWARD BIOS has any such functionality?

Problems with ATI Radeon HD 2600, electrical interference or flickering pix

Problems with ATI Radeon HD 2600, electrical interference or flickering pixels
I have a Macro 8 core purchased just 4 months ago with the ATI Radeon HD 2600. Just started getting what looks like electrical interference or flickering pixels all over the screen. It gets worse and worse to the point where i see and cant work then clears up for an hour and then comes back.
If I change the resolution from 1680x1050 to 1600x1200 everything looks fine and the problem goes away.
Monitor works fine on two other computers, driver is up to date.
Would like to upgrade at some point just disappointed that I’m already having problems.
Any suggestions would be very helpful, in the mean time I’ll searching the forums.
Thanks,

When you called Applecare or went to a Genius bar were they of no help?

T400 with ATI Radeon HD 3400. Driver not found after running ImageX.exe /Capture

Similar Messages

Maybe you are looking for