T400 won't start

Hello,
My t400 all of a sudden won't start. The battery and power lights turn on for a half a sec then off and then on again and so on. Tried disconnecting battery, cmos battery. But problem presists.
Any ideas?
Thank you

Pleaase do not post serial numbers here in the publicly visible boards.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Similar Messages

Thinkpad T400 won't start just beep 1-3-3-1

I have a thinkpad T400. Couple of months ago the problem started. I could not shut it down it just keep re-booting. I had to press and hold the start button to shut it. Now it won't boot at all. It beeps 1-3-3-1 and just sits there. When I press start button all lights come ON for a while and after only battery , AC and Ready lights stay ON. Here are few things I did so far without any luck:
1. Removed battery and AC adaptor waited few minutes put it back - same problem
2. Removed CMOS battery. DIMM cards waited for ten minutes replaced - same problem
tried with swapping DIMM cards - when I put only one card on top slot it says put the card on zero "bottom" position. After placing the Mem card on the bottom slot no thing happens. It beeps again and sit.
When I checked in the manual it says either DIMM or System board. I do not know which one is giving me the problem. I just do not want to replace all parts without knowing. Can any body help please or had similar issue and solutions if you managed to solve it. Thank you.
Roshni

Could you post your model number from under the laptop? It should be of the form 1234-ABC.
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

T400 Won't Start Up, Getting 1-3-3-1 Beep Pattern

Here's the issue:
One day I was on my computer and it ran out of batteries and the screen went dark. So I plugged it in and turned it back on. It started booting--the icon showed up and it was loading and everything, but all of a sudden the picture got really weird and pixelated and it just froze. So I turned it off and gave it some time to charge. Then I tried to turn it back on--for about 3 seconds it starts making noises and looks like its going to start, but then all the lights turn off. About a second later, it starts up again, and makes the 1-3-3-1 beeping pattern. It remains on, with the battery and power lights on, but the screen doesn't show anything. I've tried booting it up several times now with that same result.
IBM's website claims that the 1-3-3-1 pattern means there's something wrong with the DIMM or the System Board, but I have no idea what to do about either of those.
The product number is 7417 20V.
Thanks a lot for your help.

RAM dies. Just replace it.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Jane
2015 X1 Carbon, ThinkPad Slate, T410s, X301, X200 Tablet, T60p, HP TouchPad, iPad Air 2, iPhone 5S, IdeaTab A2107A, Yoga Tablet, Yoga 3 Pro
I am not a Lenovo Employee.
I AM one of those crazy ThinkPad zealots!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!

Thinkpad T400 with Vista OS won't start up

Hello all,
I'm a relatively non-proficient computer user with a T400 that is having some issues with starting up all the way. For some background, this is a pretty old computer obviously, and has had its share of trouble already. It has had one battery die and one hard drive die. Lately, it has been sporadically over-heating and turning itself off. I wouldn't be surprised if my present dilemma is the result of multiple interacting problems, but I would really appreciate if anyone could help me out.
My laptop is set to hibernate when it's closed, and today when I opened it up it was just a black screen - not a black screen like the computer was off, but like the black screen shown during start-up when no words are shown. This wasn't alarming to me because I often have to turn the computer off via the power button and then turn it back on, because opening the screen sometimes doesn't seem to force it out of hibernation. But when I did it today, I started getting this problem.
If I press the power button and then do nothing, it goes through the initial boot stages and eventually comes to a "Windows failed to start" Windows Error Recovery screen, suggesting that I launch Startup Repair. If I do launch startup repair, I get to the "System Recovery Options" window but there are no operating systems listed. When I click "Next" I'm informed I must log in to access System Recovery Options, and then I'm forced to restart, repeating the process. On the other hand, if I select to Start Windows Normally, I get that same blank black screen.
I am able to access BIOS. Here's what I have tried so far -
1. Burning Lenovo Diagnostics (http://support.lenovo.com/en_US/downloads/detail.page?&DocID=DS025448) to a bootable CD and attempting to run it on the T400. The T400 won't boot from the CD. I definitely burned it as an .iso file, and I sent the DVD-RAM drive up to the front of the boot order, and I also tried pressing F12 and selecting the drive specifically. I also changed SATA Controller Mode to "Compatability" - I don't know what that means, but I read it as a possible solution. No matter what I have tried, I hear some whirring from the CD drive during start-up, but then it stops and I end up at the same Windows Error Recovery screen.
2. HDD diagnostic program in BIOS. When I do this, the test doesn't progress at all and I get "Error code 0000: Read verification failed."
Any ideas? I've been thinking it may be time for a new laptop, but if there's a possibility of prolonging this laptop's life then I feel I might as well. Thanks in advance for your help.
Edit: Another thing I noticed is that a lot of people have T400 start-up issues due to a broken USB port. I do have a broken port, but I made sure that none of the pins are touching each other or either side. So I don't think that's the problem either.
Solved!
Go to Solution.

That drive is going bad, and fast. Read verification failure usually indicates a rather deadly flaw.
You *might* be able to insert the drive into an USB enclosure and get the files from it on another PC, but it should be done sooner than later.
Time to start shopping for a new hard drive or SSD.
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

SAP won't start after recabeling sap system

Hi, 
 
I have recently recabled my sap system (from wireless to wired) and now my sap instance won't start anymore. The weird thing is that nothing major was changed. When i read the logs from the work directory it seems it cannot load dbsdbslib.dll. I have updated to the latest version of the kernel and maxdb (kernel=7.00 patch 221, maxdb=7.6.06.07) and i made very sure i got the right kernel (NT AMD64). I also checked the environment settings for the <sid>adm user. The weird part is that it seems SAP cannot connect to the database, but the databse starts just fine and r3trans -d also returns no errors. Does anyone have an idea what could be wrong? 
 
Kind regards, 
Bas 
 
 
trc file: "dev_disp", trc level: 2, release: "700" 
 
 
command line arg 0: D:\usr\sap\IDE\DVEBMGS00\exe\disp+work.EXE 
command line arg 1: pf=D:\usr\sap\IDE\SYS\profile\IDE_DVEBMGS00_sap 
 
ERROR => DlLoadLib()==DLENOACCESS - LoadLibrary("D:\usr\sap\IDE\SYS\exe\uc\NTAMD64\dbsdbslib.dll") 
Error 126 = "The specified module could not be found." [dlnt.c 255] 
sysno 00 
sid IDE 
systemid 562 (PC with Windows NT) 
relno 7000 
patchlevel 0 
patchno 221 
intno 20050900 
make: multithreaded, Unicode, 64 bit, optimized 
pid 3252 
 
kernel runs with dp version 243000(ext=110000) (@(#) DPLIB-INT-VERSION-243000-UC) 
length of sys_adm_ext is 576 bytes 
SWITCH TRC-HIDE on *** 
***LOG Q00=> DpSapEnvInit, DPStart (00 3252) [dpxxdisp.c 1287] 
ShmProtect( 5, 3 ) 
SigIInit: ok (whoami=1) 
Thread handle for mainthread created 
SigIRegisterRoutine: handler for signal 11 installed (SigISegv) 
Pipe created:
.\pipe\SAP3252 
SigIInit: Create Message Thread 
SigIRegisterExitRoutine: exithandler installed (DpHalt) 
SigIRegisterTerminateRoutine: terminatehandler installed (DpHalt) 
 shared lib "dw_xml.dll" version 221 successfully loaded 
 shared lib "dw_xtc.dll" version 221 successfully loaded 
 shared lib "dw_stl.dll" version 221 successfully loaded 
 shared lib "dw_gui.dll" version 221 successfully loaded 
 shared lib "dw_mdm.dll" version 221 successfully loaded 
dp_loc_queue_max_blk: 40000 
mshost: >sap< 
DpSetCancelStrat: set timeout 0 at level 0 
DpSetCancelStrat: set timeout 5 at level 1 
DpSetCancelStrat: set timeout -1 at level 2 
DpSetCancelStrat: set timeout -1 at level 3 
rdisp/softcancel_sequence : -> 0,5,-1 
softcancel_sequence: >0,5,-1< 
use internal message server connection to port 3900 
msserv: >3900< 
dp_bufreftime: 120 sec 
dp_btctime: 60 sec 
dp_autoabaptime: 300 sec 
dp_autothtime: 60 sec 
dp_autojavatime: 300 sec 
dp_vm_alarm_time: 100 msec 
dp_calldelayed_time: 60 sec 
dp_startup_time: 20 
dp_noptime: 0 sec 
dp_keepalive: 1200 sec 
dp_keepalive_timeout: 60 sec 
dp_ms_keepalive: 60 sec 
dp_ms_keepalive_timeout: 300 sec 
switch off dp-keep-alive for old temus 
dp_gui_auto_logout: 0 sec 
dp_spoolalrm: 60 sec 
dp_softcancel_timeout: 5 sec 
rdisp/wp_restart_interval : 300 sec 
DpISetTrcLog: trc logging active, max size = 20971520 bytes 
dp_rfc_check_active: 1 
dp_rfc_check_all_rfcs: 0 
dp_http_check: 1 
check_master_slave: 0 
NiHsLGetServNo: got service name 'sapdp00' from operating system 
NiIGetServNo: servicename 'sapdp00' = port 0C.80/3200 
NiHsLGetServNo: got service name 'sapgw00' from operating system 
NiIGetServNo: servicename 'sapgw00' = port 0C.E4/3300 
NiIMyHostName: hostname = 'sap' 
NiHsLGetNodeAddr: got hostname 'sap' from operating system 
NiIGetNodeAddr: hostname 'sap' = addr 192.168.2.250 
NiHsLGetHostName: found address 192.168.2.250 in cache 
NiIGetHostName: addr 192.168.2.250 = hostname 'sap' (fq) 
Mon Oct 26 16:14:29 2009 
NiHsLGetNodeAddr: hostname 'www.doesnotexist0190.qqq.nxst' not found by operating system 
WARNING => DpNetCheck: NiHostToAddr(www.doesnotexist0190.qqq.nxst) took 12 seconds 
Mon Oct 26 16:14:45 2009 
NiHsLGetHostName: address 1.0.0.1 not found by operating system 
WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 16 seconds 
NiHsLGetServNo: got service name 'http' from operating system 
NiIGetServNo: servicename 'http' = port 00.50/0080 
NiHsLGetServName: port 1F.90/8080 not found by operating system 
NiHsLGetServName: port FC.2B/64555 not found by operating system 
NiHsLGetServNo: service name 'sapdp9988' not found by operating system 
***LOG GZZ=> 2 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 5521] 
SigIRegisterRoutine: handler for signal 16 installed (DpTrcOnOff) 
SigIRegisterRoutine: handler for signal 17 installed (DpTrcOnOff) 
SigIRegisterRoutine: alarm handler installed (DpSigAlrm) 
SigIRegisterRoutine: handler for signal 2 installed (DpSigInt) 
SigIRegisterRoutine: handler for signal 15 installed (DpSigInt) 
SigIRegisterRoutine: handler for signal 3 installed (DpSigQuit) 
MtxInit: 30000 0 0 
DpInitMtx: MtxInit o.k. 
PPID environment not found 
Thread handle for mainthread created 
SigIRegisterRoutine: handler for signal 19 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 18 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 24 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 0 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 21 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 22 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 23 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 25 installed (DpSigPrivDisp) 
 
 
trc file: "dev_w0", trc level: 2, release: "700" 
 
* 
ACTIVE TRACE LEVEL 2
ACTIVE TRACE COMPONENTS all, MJ
M
M command line arg 0: D:\usr\sap\IDE\DVEBMGS00\exe\disp+work.EXE
M command line arg 1: pf=D:\usr\sap\IDE\SYS\profile\IDE_DVEBMGS00_sap
M command line arg 2: wp_id=0
M
B create_con (con_name=R/3)
B Loading DB library 'D:\usr\sap\IDE\SYS\exe\uc\NTAMD64\dbsdbslib.dll' ...
M *** ERROR => DlLoadLib()==DLENOACCESS - LoadLibrary("D:\usr\sap\IDE\SYS\exe\uc\NTAMD64\dbsdbslib.dll")
Error 126 = "The specified module could not be found." [dlnt.c 255]
B *** ERROR => Couldn't load library 'D:\usr\sap\IDE\SYS\exe\uc\NTAMD64\dbsdbslib.dll'
[dbcon.c 4905]
M sysno 00
M sid IDE
M systemid 562 (PC with Windows NT)
M relno 7000
M patchlevel 0
M patchno 221
M intno 20050900
M make: multithreaded, Unicode, 64 bit, optimized
M pid 4000
M
M kernel runs with dp version 243000(ext=110000) (@(#) DPLIB-INT-VERSION-243000-UC)
M length of sys_adm_ext is 576 bytes
M ***LOG Q0Q=> tskh_init, WPStart (Workproc 0 4000) [dpxxdisp.c 1349]
M Mon Oct 26 16:14:47 2009
M SigIInit: ok (whoami=2)
M Thread handle for mainthread created
M SigIRegisterRoutine: handler for signal 11 installed (SigISegv)
M Pipe created:
.\pipe\SAP4000
M SigIInit: Create Message Thread
M SigIRegisterExitRoutine: exithandler installed (wp_halt)
M SigIRegisterTerminateRoutine: terminatehandler installed (wp_halt)
M SigIRegisterRoutine: handler for signal 16 installed (DpTrcOnOff)
M SigIRegisterRoutine: handler for signal 17 installed (DpTrcOnOff)
M SigIRegisterRoutine: alarm handler installed (DpSigAlrm)
M SigIRegisterRoutine: handler for signal 2 installed (DpSigInt)
M SigIRegisterRoutine: handler for signal 15 installed (DpSigInt)
M SigIRegisterRoutine: handler for signal 3 installed (DpSigQuit)
I MtxInit: 30000 0 0
M DpInitMtx: MtxInit o.k.
M WaitParent Thread 3252 start
M WaitParent Thread 3252 created
M Thread handle for mainthread created
M SigIRegisterRoutine: handler for signal 19 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 18 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 24 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 0 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 21 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 22 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 23 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 25 installed (DpSigPrivDisp)
 
 
trc file: "trans.log" 
 
 
4 ETW000 r3trans version 6.14 (release 700 - 12.06.09 - 15:20:00).
4 ETW000 unicode enabled version
4 ETW000 ===============================================
4 ETW000
4 ETW000 date&time : 21.10.2009 - 15:06:04
4 ETW000 control file: <no ctrlfile>
4 ETW000 R3trans was called as follows: r3trans -d
4 ETW000 trace at level 2 opened for a given file pointer
4 ETW000 [dev trc ,00000] Wed Oct 21 15:06:06 2009 0 0.000000
4 ETW000 [dev trc ,00000] db_con_init called 0 0.000000
4 ETW000 [dev trc ,00000] create_con (con_name=R/3) 0 0.000000
4 ETW000 [dev trc ,00000] Loading DB library 'dbsdbslib.dll' ... 0 0.000000
4 ETW000 [dev trc ,00000] DlLoadLib success: LoadLibrary("dbsdbslib.dll"), hdl 0, addr 0000000188C00000
4 ETW000 7580 0.007580
4 ETW000 [dev trc ,00000] using "D:\usr\sap\IDE\SYS\exe\uc\NTAMD64\dbsdbslib.dll" 16 0.007596
4 ETW000 [dev trc ,00000] Library 'dbsdbslib.dll' loaded 19 0.007615
4 ETW000 [dev trc ,00000] function DbSlExpFuns loaded from library dbsdbslib.dll 38 0.007653
4 ETW000 [dev trc ,00000] Version of 'dbsdbslib.dll' is "700.08", patchlevel (0.211) 307 0.007960
4 ETW000 [dev trc ,00000] function dsql_db_init loaded from library dbsdbslib.dll 26 0.007986
4 ETW000 [dev trc ,00000] function dbdd_exp_funs loaded from library dbsdbslib.dll 24 0.008010
4 ETW000 [dev trc ,00000] } DbSlSdbControl(rc=0) 46 0.008056
4 ETW000 [dev trc ,00000] { DbSlSdbControl(con_hdl=-1,command=39,arg_p=0000000000000000) 21 0.008077
4 ETW000 [dev trc ,00000] } DbSlSdbControl(rc=0) 15 0.008092
4 ETW000 [dev trc ,00000] { DbSlSdbControl(con_hdl=-1,command=10,arg_p=0000000003B4F920) 20 0.008112
4 ETW000 [dev trc ,00000] } DbSlSdbControl(rc=0) 15 0.008127
4 ETW000 [dev trc ,00000] New connection 0 created 17 0.008144
4 ETW000 [dev trc ,00000] 000: name = R/3, con_id = -000000001, state = DISCONNECTED, tx = NO , hc = NO , perm = YES,
4 ETW000 reco = NO , frco = NO , timeout = 000, con_max = 255, con_opt = 255, occ = NO
4 ETW000 50 0.008194
4 ETW000 [dev trc ,00000] { DbSlSdbControl(con_hdl=-1,command=10,arg_p=0000000001A01768) 31 0.008225
4 ETW000 [dev trc ,00000] } DbSlSdbControl(rc=0) 17 0.008242
4 ETW000 [dev trc ,00000] db_con_connect (con_name=R/3) 13 0.008255
4 ETW000 [dev trc ,00000] find_con_by_name found the following connection for reuse: 16 0.008271
4 ETW000 [dev trc ,00000] 000: name = R/3, con_id = 000000000, state = DISCONNECTED, tx = NO , hc = NO , perm = YES,
4 ETW000 reco = NO , frco = NO , timeout = 000, con_max = 255, con_opt = 255, occ = NO

Edited by: B. v. d. Lienden on Oct 26, 2009 5:18 PM

<div class=Section1>
Natalia,
 
To answer your questions:
1. Did you create the SAP ticket, where this problem is
reported?
I didn't report it to SAP because it is just an IDES test
system. I can easily do a reinstall, but i would like to know the cause and
solution to this problem.
 
2. Do you have dbsdbslib.dll at this location? What version?
Yes, i have the dbsdbslib.dll at location
D:\usr\sap\IDE\DVEBMGS00\exe and also D:\usr\sap\IDE\SYS\exe\uc\NTAMD64
Version is 7000.221.16.41497 (kernel 7.00 SP 221)
 
your requested output:
 
----

disp+work information
----

 
kernel releaseu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 700
 
kernel make variantu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 700_REL
 
compiled onu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 NT 5.2 3790 Service Pack 2 x86
MS VC++ 14.00
 
compiled foru00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 64 BIT
 
compilation modeu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 UNICODE
 
compile timeu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 Aug 23 2009 23:15:57
 
update level u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A00
 
patch numberu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 221
 
source idu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 0.221
 
 
----

supported environment
----

 
database (SAP, table SVERS)u00A0u00A0 700
u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 
operating system
Windows NT 5.0
Windows NT 5.1
Windows NT 5.2
Windows NT 6.0
ALLUSERSPROFILE=C:\Documents and Settings\All Users
APPDATA=C:\Documents and Settings\ideadm\Application Data
CLIENTNAME=BSF02
ClusterLog=C:\WINDOWS\Cluster\cluster.log
CommonProgramFiles=C:\Program Files\Common Files
CommonProgramFiles(x86)=C:\Program Files (x86)\Common Files
COMPUTERNAME=SAP
ComSpec=C:\WINDOWS\system32\cmd.exe
DBMS_TYPE=ada
DIR_LIBRARY=D:\usr\sap\IDE\SYS\exe\uc\NTAMD64
DIR_PROFILE=D:\usr\sap\IDE\SYS\profile
FP_NO_HOST_CHECK=NO
HOMEDRIVE=C:
HOMEPATH=\Documents and Settings\ideadm
JAVA_HOME=C:\j2sdk1.4.2_21-x64
LOGONSERVER=
SAP
NUMBER_OF_PROCESSORS=2
OS=Windows_NT
Path=D:\sapdb\programs\bin;D:\sapdb\programs\pgm;C:\j2sdk1.4.2_21-x64\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Program
Files\Intel\DMIX;D:\usr\sap\IDE\SYS\exe\uc\NTAMD64
PATHEXT=.COM;.EXE;.BAT;.CMD;.VBS;.VBE;.JS;.JSE;.WSF;.WSH
PROCESSOR_ARCHITECTURE=AMD64
PROCESSOR_IDENTIFIER=EM64T Family 6 Model 15 Stepping 13,
GenuineIntel
PROCESSOR_LEVEL=6
PROCESSOR_REVISION=0f0d
ProgramFiles=C:\Program Files
ProgramFiles(x86)=C:\Program Files (x86)
PROMPT=$P$G
SAPEXE=D:\usr\sap\IDE\SYS\exe\uc\NTAMD64
SAPLOCALHOST=sap
SAPSYSTEMNAME=IDE
SESSIONNAME=RDP-Tcp#47
SystemDrive=C:
SystemRoot=C:\WINDOWS
TEMP=C:\WINDOWS\TEMP\2
TMP=C:\WINDOWS\TEMP\2
USERDOMAIN=SAP
USERNAME=ideadm
USERPROFILE=C:\Documents and Settings\ideadm
windir=C:\WINDOWS
 
----

disp+work information
----

 
kernel releaseu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 700
 
kernel make variantu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 700_REL
 
compiled onu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 NT 5.2 3790 Service Pack 2 x86
MS VC++ 14.00
 
compiled foru00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 64 BIT
 
compilation modeu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 UNICODE
 
compile timeu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 Aug 23 2009 23:15:57
 
update levelu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 0
 
patch numberu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 221
 
source idu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 0.221
 
 
----

supported environment
----

 
database (SAP, table SVERS)u00A0u00A0 700
u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 
operating system
Windows NT 5.0
Windows NT 5.1
Windows NT 5.2
Windows NT 6.0
 
 
</div>

My iPhone 5 won't start!

My Iphone 5 won't start and tells me to connect the phone to ITunes but nothing happens when I do. The phone doesn´t show up in ITunes. What to do?

Apologies, 11.0.4 is the most recent of course...
You'll need to enter DFU mode.
Connect the iPhone to your computer and launch iTunes
Turn the iPhone off (hold down the power button at the top of the iPhone)
Hold down the sleep/power button and home button together for exactly 10 seconds, then release the power button
Continue to hold down the Home button until a message appears in iTunes telling you an iPhone in recover mode has been detected
Hopefully this should work, with you being able to restore the device in iTunes.
However, be warned that this will erase all content on the iPhone, content you can restore if you have saved backups on your Mac/PC or on iCloud.

Ok so I updated to iOS 7 on my iPod (5th) it let me update my apps but I cannot download new apps thanks to the terms and conditions. Also my iTunes won't start it just blank, I tried everything I need help

Ok so I updated to iOS 7 on my iPod (5th) it let me update my apps but I cannot download new apps thanks to the terms and conditions. Also my iTunes won't start it just blank, I tried everything I need help

Did you download the new iTunes update that was also released this afternoon? That might be the problem. The new iTunes update came out today as well as the new iOS 7 update and if you haven't downloaded the new iTunes update it may be a compatibility problem so if you didn't, first update to the new iTunes and try again.

All of a sudden Photoshop won't start [on a Macbook Air]

Dear all,
I'm on a MacBook Air with OS X 10.10.2, and I use Photoshop about once a month, but now I really need it, and it won't start:
- Immediately after I click on the Photoshop icon I get "Adobe Photoshop CS5.1 cannot be opened because of a problem." And when I click on the "Report..." button I get a very technical message (see below).
- I've used Photoshop on this machine for about a year with no problem, but recently I had a problem and needed to restore from my TimeMachine backup.
- I don't know if the problem occurred immediately after the restore or not.
- I've read innumerable threads on various forums, but nothing describes my problem exactly. I suspect a problem with my paths and permissions (since I read a report that restoring from a TimeMachine causes such problems occasionally), but I don't know which path is corrupted/missing/unreadable.
- I've tried creating a new admin account and starting Photoshop from there. It didn't work.
- I don't mind reinstalling, but I don't have an installer image. I started with Photoshop 6, then updated to CS2, CS4 and eventually CS5. I do have all the serial numbers but not all update-images.
I would appreciate any hints on how to further diagnose and some the problem.
Thanks a lot in advance!
Bojidar
And now here is my exact error message:
Process: Adobe Photoshop CS5.1 [12426]
Path: /Applications/Bildbearbeitung/*/Adobe Photoshop CS5.1.app/Contents/MacOS/Adobe Photoshop CS5.1
Identifier: com.adobe.Photoshop
Version: ???
Code Type: X86-64 (Native)
Parent Process: ??? [1]
Responsible: Adobe Photoshop CS5.1 [12426]
User ID: 501
Date/Time: 2015-05-03 21:53:39.840 +0200
OS Version: Mac OS X 10.10.1 (14B25)
Report Version: 11
Anonymous UUID: A0DC6EA7-1973-1B68-EFC7-5D60106F084D
Sleep/Wake UUID: 1FA6367C-EEB2-4F46-8773-EBB176EAEAC7
Time Awake Since Boot: 230000 seconds
Time Since Wake: 2900 seconds
Crashed Thread: 0
Exception Type: EXC_BREAKPOINT (SIGTRAP)
Exception Codes: 0x0000000000000002, 0x0000000000000000
Application Specific Information:
dyld: launch, loading dependent libraries
Dyld Error Message:
Library not loaded: @executable_path/../Frameworks/adobe_caps.framework/Versions/A/adobe_caps
Referenced from: /Applications/Bildbearbeitung/*/Adobe Photoshop CS5.1.app/Contents/MacOS/Adobe Photoshop CS5.1
Reason: image not found
Binary Images:
 0x7fff6f1c1000 - 0x7fff6f1f7837 dyld (353.2.1) <4696A982-1500-34EC-9777-1EF7A03E2659> /usr/lib/dyld
Model: MacBookAir6,2, BootROM MBA61.0099.B18, 2 processors, Intel Core i5, 1.3 GHz, 4 GB, SMC 2.13f15
Graphics: Intel HD Graphics 5000, Intel HD Graphics 5000, Built-In
Memory Module: BANK 0/DIMM0, 2 GB, DDR3, 1600 MHz, 0x80AD, 0x483943434E4E4E384A544D4C41522D4E544D
Memory Module: BANK 1/DIMM0, 2 GB, DDR3, 1600 MHz, 0x80AD, 0x483943434E4E4E384A544D4C41522D4E544D
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x117), Broadcom BCM43xx 1.0 (7.15.124.12.10)
Bluetooth: Version 4.3.1f2 15015, 3 services, 19 devices, 1 incoming serial ports
Network Service: Wi-Fi, AirPort, en0
Serial ATA Device: APPLE SSD SM0256F, 251 GB
USB Device: Internal Memory Card Reader
USB Device: BRCM20702 Hub
USB Device: Bluetooth USB Host Controller
Thunderbolt Bus: MacBook Air, Apple Inc., 23.6

Did tou try resetting the preferences usins the Photoshop keys as your tryind to start Photoshop. Toy cab also use Windows explored or Mac finder deleteor rename you userid Photoshop preferende if you change you OS preferences to be able to see hiddeb files and folders. Do you read the link I posted?
Restore preference files to default
In this video, learn the two methods of resetting your preference files back to default: Manual preference file removal and Keyboard Shortcut method (starts at 5:05)
by Julieanne Kost
To restore preferences quickly using a keyboard short cut:
Press and hold Alt+Control+Shift (Windows) or Option+Command+Shift (Mac OS) as you start Photoshop. You are prompted to delete the current settings. The new preferences files are created the next time you start Photoshop.
Note: Using the keyboard shortcut, preference files for custom shortcuts, workspaces, and color setings will also be reset to default.

X11 won't start anymore!

Hello,
this is a desperate call: I am at a conference with my MBP, (10.6.7, all updates done). I need Matlab for my presentation, which needs X11.
X11 (and XQuartz) decided that they won't start anymore: the icon bounces in the dock for a while, then sits there without the little light underneath, and X11 is "non responding".
The logs show something like this.
I have googled and searched: similar problems once in a while appear but no posted solution.
I tried:
1) reinstalling XQuartz (I would reinstall X11, but how? I do not have the disks with me, I am away!)
2) from an admin account
3) create a new account.
4) repair permissions.
5) reinstall the font update from Apple that was recently issued.
HELP PLEASE!!!
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     X11.app: DISPLAY ("/tmp/launch-bHvQen/org.macosforge.xquartz:0") does not match our id ("org.x"), unsetting.
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     X11.app: main(): argc=2
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]      argv[0] = /Applications/Utilities/X11.app/Contents/MacOS/X11.bin
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]      argv[1] = -psn_0_278596
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     Waiting for startup parameters via Mach IPC.
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     X11.app: Could not connect to server (DISPLAY is not set). Starting X server.
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     X11.app: Launching /usr/X11/bin/startx:
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]      argv[0] = /bin/sh
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]      argv[1] = -c
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]      argv[2] = /usr/X11/bin/startx
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     font_cache: Scanning user font directories to generate X11 font caches
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     font_cache: Updating FC cache
11-05-16 5:02:01 PM     org.x.privileged_startx[20781]     font_cache: Scanning system font directories to generate X11 font caches
11-05-16 5:02:01 PM     defaults[20791]
The domain/default pair of (org.x.X11, dpi) does not exist
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     Couldn't create cookie
11-05-16 5:02:02 PM     org.x.privileged_startx[20781]     font_cache: Updating FC cache
11-05-16 5:02:04 PM     [0x0-0x44044].org.x.X11[20759]     font_cache: Done
11-05-16 5:02:04 PM     org.x.privileged_startx[20781]     font_cache: Done

Here is the solution: there was nothing wrong with x11 per se!
The problem was that about 30 files in /usr/bin (like gzip, egrep, hexdump etc) had been hosed (they had 0 file size). The puzzling messages was due to the fact that startx uses hexdump, which was simply silently doing nothing (since it had 0 size!).
I do not know what or when these files were zeroed: I suspect a recent OSX update which did not complete and I had to forcefully reboot.
I have fixed it enough to work (copying those files from another mac), but who knows what else lurks beneath the surface of apparent serenity!
I am actually surprised that the whole system did not stop functioning completely.
MORALE: if something looks strange in the logs with x11 or other apps, check the file sizes in your /usr/bin, you may be surprised too!

24" iMac won't start when iPod is connected

My 24" iMac won't start up/restart if my iPod is already connected to it. If I restart with the iPod connected, I just get a gray screen (with no apple logo) forever. Has anyone else experienced this problem? If so, any solution? I have Windows installed with boot camp, don't know if that's the problem, but I tried reseting the p-ram, but to no avail...
Intel iMac 24", 7600 GT, 500GB, 2GB. Titanium Powerbook 667 MHz G4, loaded. Mac OS X (10.4.7) 30 GB iPod Video

My suggestion would be disconnect the iPod. That's just me though.
http://docs.info.apple.com/article.html?artnum=93953
I'm guessing Boot Camp is the culprit. Whatever emulated BIOS it's using doesn't like the iPod as a startup disk.

I was messing around with .kext files in the MacintoshHD and now my MacBook Pro won't start up.

I was messing around with .kext files in the MacintoshHD and moved the system.kext and two others to my desktop and deleted the originals and now the MacBook Pro won't start up. All I get at start up is the apple icon then a bunch of text shows up part of which says Mac OS version: not yet set. then the apple icon turns into the power icon and tells me to turn off the computer. I've tried reinstalling from the install DVD by holding down option when powering on and selecting the install DVD and it just goes to a white screen with the apple icon and stays like that. I didn't have the disk utility on my Mac before this happened because I deleted it to make room on my computer a while ago so I'm not sure if that's why it won't load the install DVD but anyone who knows the solution to this with out going to get it repaired would be greatly appreciated. Thank you!

Never mind my dad just found the original install DVD and that worked. Before I was using an install disc that Apple sent me for another issue I was having, but thanks for replying so quickly and trying to help on this Thanksgiving day!!!

I deleted my extensions manager and now my Mac won't start up. Please Help!!

I have an IMac, 24" model, running OS X. For the past several days, little warning windows have been popping up with this annoying beep, telling me that my computer was infected with various viruses. 4, to be exact. Also, while on the internet, random pop-up windows have appeared, so I thought I did have a virus. So, to correct the matter (or attempt to), I deleted my preferences folder from the system folder, as well as the extensions manager.
Now, the computer won't start up past the white logo screen with the turning gear thingy. I've tried resetting the PRAM, and starting in safe mode, and safe mode with the progress screen, and even something there while holding the option key (that one gave me an icon of my HD, but clicking on it took me back to an endless wait on the white screen). I've tried starting from the disk that came with the computer (I held the C key) but not only doesn't the computer start from the disk, it spits the disk out. I don't understand. The computer was fine until I deleted the ext. mgr and preferences, so it can't be that the computer went bad or something.
I don't know what else to do here. I do have an extended service warranty with Best Buy, but I wanted to see if there was some way to fix this before hauling this thing off to the store. Any suggestions? I'm desperate here, because anything and everything I've tried (based on all the try-this and try-thats I found on the internet), nothing has worked.
Please help.
Thanks in advance.

Well done! You've succeeded in turning your Mac into a useless brick.
Deleting the System/Library/extensions folder and the associated manager removed most of the functionality from your OS.
And all to get rid of what sounds like the MacDefender trojan or a variant.
ref; http://support.apple.com/kb/HT4650 and http://support.apple.com/kb/HT4651
You may have a slim chance of recovering if it will still boot in Target Disc Mode; in which case you can use another Mac to install the system remotely.
And I doubt your warranty with Best Buy is going to cover user "error."
Message was edited by: noondaywitch

After reboot firefox won't start. runs in task manager, but won't pop up. reset, safe mode and uninstall/re-install won't help. ok if no reboot.

win7 Pro. has been running firefox ok. but lately with 25 and now 26, the firefox won't start. I can see firefox is running in task manager. but it just won't pop up.
if I download it again and install it, it will run, but every time I reboot the system, it just won't run again.
try: reset, safe mode, uninstall & reinstall, new/clean profile, none of those work.

There may be a corrupted file on Firefox. 
Please attempt to perform a clean reinstall. [https://support.mozilla.org/en-US/kb/forum-response-clean-reinstall (More Details)] This is different than a regular uninstall.
If a clean reinstall does not fix the issue, please try starting your operating system in safe mode. 
To do so, please do the following:
#Ensure that your computer is shut down completely
#Press the power button
#Tap the <code>F8</code> key repeatedly before the Windows logo and startup screen is displayed
#Select Safe Mode With Networking for the advanced startup options list
Please report back with the results of both solutions.

I am upgrading to Calendar Server 4.0 on NT with more than 9 nodes (or I already have) and my server won't start

I am upgrading to Calendar Server 4.0 on NT with more than 9 nodes
(or I already have) and my server won't start.

The steps are the same whether you have already upgraded or are about to.

Calendar Server 4.0 on the Windows NT platform can only support up to nine
nodes on one server, while 3.51 supported up to 14. If you have a Calendar
Server 3.51 with more than 9 nodes that you want to upgrade to Calendar Server
4.0, Netscape recommends that you migrate the extra nodes to another Calendar
Server 3.51 on another Windows NT system. To accomplish this:
<OL>
<LI>Install Calendar Server on another Windows NT machine and configure it to
use the same directory server as your current Calendar Server.
<LI>Stop and backup your current Calendar Server.
<LI>Individually zip up the node directories you want to move to the new
server. (drive:\unsers\unison\db\Nx
where "x" is the number of the node you want to use.)
<LI>Stop the new Calendar Server.
<LI>Unzip the files into the new Calendar Server in the same place as they
were on the old server.
<LI>Edit the unison.ini
file on the new server to add the nodes you have just migrated.
<LI>Edit the unison.ini
file on the old server to remove the nodes you have moved to the new server.
<LI>Edit the nodes.ini
file on the old server to remove the nodes you just moved and then add them
with the new hostname. Keep in mind that you will only be able to modify the
node network from the old host.
<LI>Run unidbfix -export
on both servers for all nodes.
<LI>Edit the remotenodes.ini
file on both servers to reflect your node topology.
<LI>Run unidbfix -import
to import the changes into the node databases.
<LI>Run unidbfix -c,
then -f,
then -c
again on both servers for all the nodes.
<LI>If you don't get any errors, run uninode -test all
to test if your nodes connections are set properly. If they are not, do not
start either of the servers; instead, fix the errors and try again.
<LI>Start both servers.
<LI>Log in and check to see if you can see people on remote nodes.
<LI>Notify the users on the moved nodes of their new calendar host.
<LI>If you did this in preparation of an upgrade, you can now run the upgrade to
4.0 since both servers contain fewer than 9 nodes.
</OL>

Use Disk Utility whihc is in the Utilities Folder.
Select your Boot Disk on the left.
Select Verify Permissions
If any errors the do Reapir permissions.
You might have to repeat the process.
see this:
Steve

Password service won't start

Following an unplanned hard restart of our server (Mac OS X 10.9.5, Server 3.2.2), the password service won't start, so our staff can't log into mail, calendars or file sharing.
When I launch Open Directory, the main window has the message "Unable to load replica list", then it switches itself off after a minute or so.
I've looked at the certificates in Server and they have the green tick so presumably are OK.
DNS is working OK and running the command "sudo changeip -checkhostname" reports success.
Here's the section of log that repeats every few seconds as PasswordService repeatedly starts up and exits:
13/03/2015 20:55:00.617 com.apple.launchd[1]: (com.apple.PasswordService[5890]) Exited with code: 1
13/03/2015 20:55:00.617 com.apple.launchd[1]: (com.apple.PasswordService) Throttling respawn: Will start in 10 seconds
13/03/2015 20:55:02.540 xscertd[249]: Failed sending LookupCRLByCARecordName command to com.apple.xscertd.helper: The operation couldn’t be completed. (com.apple.certificateserver error 42005.)
13/03/2015 20:55:08.708 com.apple.launchd[1]: (org.openldap.slapd[5894]) Exited with code: 1
13/03/2015 20:55:08.708 com.apple.launchd[1]: (org.openldap.slapd) Throttling respawn: Will start in 7 seconds
13/03/2015 20:55:10.206 xscertd-helper[5897]: ldap_search_ext_s returned -1 - Can't contact LDAP server when searching for bdb suffix, exiting
13/03/2015 20:55:10.207 com.apple.launchd[1]: (com.apple.xscertd-helper[5897]) Exited with code: 1
13/03/2015 20:55:10.207 com.apple.launchd[1]: (com.apple.xscertd-helper) Throttling respawn: Will start in 10 seconds
13/03/2015 20:55:10.639 PasswordService[5901]: -[PasswordServerPrefsObject getSearchBase]: Unable to locate search base: -1 Can't contact LDAP server
13/03/2015 20:55:10.639 PasswordService[5901]: -[PasswordServerPrefsObject loadXMLData]: Unable to locate passwordserver config record's plist attribute: -1 Can't contact LDAP server
13/03/2015 20:55:10.640 PasswordService[5901]: -[PasswordServerPrefsObject getSearchBase]: Unable to locate search base: -1 Can't contact LDAP server
13/03/2015 20:55:10.640 PasswordService[5901]: -[PasswordServerPrefsObject saveXMLData]: ldap_modify_ext_s of the passwordserver config record's plist attribute: -1 Can't contact LDAP server
13/03/2015 20:55:10.684 PasswordService[5901]: int pwsf_GetPublicKey(char *): ldap_search_ext_s cn=authdata for Public Key returned -1
13/03/2015 20:55:10.687 com.apple.launchd[1]: (com.apple.PasswordService[5901]) Exited with code: 1
I have backups (both Time Machine and clones of the hard drive) that I could use to restore the corrupted bit of the configuration, if necessary, but I don't know what to restore.

Many Open Directory problems can be resolved by taking the following steps. Test after each one, and back up all data before making any changes.
1. The OD master must have a static IP address on the local network, not a dynamic address. It must not be connected to the same network with more than one interface; e.g., Ethernet and Wi-Fi.
2. You must have a working DNS service, and the server's hostname must match its fully-qualified domain name. To confirm, select the server by name in the sidebar of the Server application window, then select the Overview tab. Click the Edit button on the Host Name line. On the Accessing your Server sheet, Domain Name should be selected. Change the Host Name, if necessary. The server must have at least a three-level name (e.g. "server.yourdomain.com"), and the name must not be in the ".local" top-level domain, which is reserved for Bonjour.
3. The primary DNS server used by the server must be itself, unless you're using another server for internal DNS. The only DNS server set on the clients should be the internal one, which they should get from DHCP if applicable.
4. If you have accounts with network home directories, make sure the URL's are correct in the user settings. A return status of 45 from the authorizationhost daemon in the log may mean that the URL for mounting the home directory was not updated after a change in the hostname.
5. Only if you're still running Mavericks server, follow these instructions to rebuild the Kerberos configuration on the server.
6. If you use authenticated binding, check the validity of the master's certificate. The common name must match the hostname and domain name. Deselecting and then reselecting the certificate in Server.app has been reported to have an effect in some cases. Otherwise delete all certificates and create new ones.
7. Unbind and then rebind the clients in the Users & Groups preference pane. Use the fully-qualified domain name of the master.
8. Reboot the master and the clients.
9. Don't log in to the server with a network user's account.
10. Disable any internal firewalls in use, including third-party "security" software.
11. If you've created any replica servers, delete them.
12. If OD has only recently stopped working when it was working before, you may be able to restore it from the automatic backup in /var/db/backups, or from a Time Machine snapshot of that backup.
13. As a last resort, export all OD users. In the Open Directory pane of Server, delete the OD server. Then recreate it and import the users. Ensure that the UID's are in the 1001+ range.
If you get this far without solving the problem, then you'll need to examine the logs in the Open Directory section of the log list in the Server app, and also the system log on the clients.

T400 won't start

Similar Messages

Maybe you are looking for