T410 will not boot with new SSD

I've cloned my HDD to a new SSD, but it will not boot. It goes into a Lenovo Think Bios splash screen / Black screen loop. I booted off a repair disk and performed a repair, but it is still doing the bios loop thing. This has happened with both an OCZ and a Kingston SSD. Any ideas? Thanks...
Solved!
Go to Solution.

I'm going to venture a guess that the drive was not cloned properly.
The "new" drive must be in the machine's HDD bay, and the "old" one in the USB enclosure.
I always use Clonezilla for the rare occasions that I actually clone something, but Acronis should do just fine as well.
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Similar Messages

Windows 8 will not activate with new SSD (second) hard drive

I added a new SSD drive in the second hard drive bay. I used the HP restoration media to install Windows 8 on the new SSD drive. Windows 8 will not activate. After spending 90 minutes on the phone with HP support (and paying $150), they told me to contact Microsoft. After spending some time with Microsoft, they told me that the Windows product key is being locked by HP, and there is nothing they can do.

Hi badgerbuzz,
I have brought your issue to the attention of an appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publically post ( serial numbers and case details).
If you are unfamiliar with how the Forum's private message capability works, you can learn about that here.
Regards,
George
I work for HP

Snow Leopard will not boot on new SSD

I purchased a 120 GB SSD for my 2007 MBP (A1226) and installed it. The old drive crashed and I am looking for a clean install - not time machine. I have tried to boot from the OSX 10.6 Install Disk but it keeps getting stuck!
1. I power on the MBP
2. When the chime sounds, I hold down the option button
3. The screen gives me the option to select the disk
4. The apple logo is displayed and the little spinning wheel thing goes on for a while
5. It goes to a light blue/gray screen and then doesn't do anything.
I'd really appreciate some guidance. I am not proficient at computer repairs. I'm just trying to get this machine spun up for my wife and kids to use for email/internet.
Thanks!
Finch

Hello,
First, you have to erase (format) the new SSD drive before installation.
I first watched this video:
https://www.youtube.com/watch?v=cfiGF_pjqvM
Here it is also step by step:
Upgrading Your MacBook Pro with a Solid State Drive
Good luck!

Will not boot with new hard drive

I used a SATA drive with adaptor as a boot drive in an MDD for most of the past year. I just got a MacPro 5,1 and wanted to use this SATA drive as a data drive in the new computer. I pulled it out of the MDD and put it in the MacPro. On start up I get the message You need to hold the power button or press restart. Since it has a boot volume I thought this might be a problem. I held down the Option key during start up to select a boot drive. Here it shows both the this drive and the OEM MacPro drive. Which ever I select I still get the error message. I can put this back in the MDD and get the same error even though it shows up as a boot volume when holding the Option Key. This drive does not seem to be totally dead since it can be seen during start up but it wont let the computer finish booting. It gets to the Apple logo but no farther. Can I salvage this drive? Data on it is unimportant.

You really need to use FW case; reformat the drive to use GPT partition table.
When booting the system's EFI polls all drives to look for valid system paths and to see which is blessed. A corrupt directory can even prevent booting from any drive or DVD.
I tell G5 owners to reformat as soon as possible once data is recovered, even though if they were running 10.5.8 their SATA drive may be okay.
Nuke the drive one way or another, I'd assume you have a spare FW case. And try booting from OS X DVD - you can install a fresh OS as backup/emergency system drive.
Any new SATA II or III drive are fine, WD Black are popular and 640 $69 or 1TB $89.
Have fun, I went from G4 MDD to Mac Pro over 4 yrs ago and it is still running strong -- and quiet!

T43 – Model 1871-FU1: Will not boot with blank screen. Only Fan is running. Any ideas?

T43 – Model 1871-FU1: Will not boot with blank screen. Only Fan is running. Any ideas?
Solved!
Go to Solution.

What lead_org is referring to is commonly known as "re-balling" which involves unsoldering the Southbridge chip from the planar, replacing all (6-700) solder balls with new ones and then re-attaching it under heat/pressure.
This is the place that you need:
http://www.theboardroom.info/index.html
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Cannot boot with new SSD

Installed new OWC 240G SSD in 2007 iMac. Started up with old HD in external case running OS 10.10.2. Initialized SSD with Disk Utilities, and it mounted on the desktop. Transferred contents from old HD to new SSD. Computer boots fine from old HD in external case, but does not boot with internal SSD. After displaying Apple symbol for a few seconds of the startup process, computer goes to a kernel panic and gets into a loop of retry message-Apple symbol-message-etc. The SSD shows on the desktop, but does not show as a startup disk in System Preferences pane. Disk Utilities shows drive is fine, but repair of permissions is grayed out. Window says permissions repair is only permitted on OS installed with an Apple installer. System folder on the SSD does not show the "blessed" symbol. Have tried recloning using Time Machine backup - same result. Installed eDrive on SSD with TechToolsPro, and can start up in eDrive thru TTP window, thus verifying all cabling. After booting with original internal HD installed in external case, SSD will show on desktop, but will disappear in a few minutes after a message says it was improperly ejected. Suggestions? Is there a way to access OS 10 software purchased and downloaded from Apple site?

Many possibilities here. Maybe a bad connection when you installed the drive. Maybe a bad drive. Maybe a bad SATA cable.
How did you format the drive? Should be Mac OS Extended Journaled. When you boot into the recovery drive, access disk utility from there and see if you can access the drive.
I have the same drive as you. What I did is use Disk Utility from the recovery drive of TM. I first re-formatted the SSD drive. Then I used Disk Utility to restore the whole drive of my original to the new SSD drive.
You can still download the Yosemite installer from the App Store in your purchases providing you downloaded it from the App Store already.

HP G62 Will Not Boot With Power Cord Plugged In

I have an HP G62 laptop that is about four years old. I've had a couple of problems with it before that were resolved relatively satisfactorily, however five or six months ago I started having a new issue. The laptop will not boot with the charging cord plugged in, whether there is a battery in it or not. Nor will it return from sleep mode (screen black, status light on the power button flashing) with the charging cord plugged in, whether there is a battery in it or not. It simply shuts down and I end up with an error screen the next time I boot up. I have tried other charging cords and it has been the same, however the cord will still charge the battery. This means I have to charge the battery, unplug the cord, boot up the computer. This annoyance is worsened by the fact that the battery is old and unable to hold charge for very long at all and I fear one day even the battery won't be enough to boot the computer.Can I fix the power cord issue? Should I buy a new battery? Or let my computer give up the ghost and scrounge for a new one? Any help would be greatly appreciated.

the charger input could possibly need replaced and/or the charger

My ipod 5.1.1 (9B206) will not sync with new Itunes version 12.0.1.26. Can anyone help

My ipod touch 3rd generation OS 5.1.1 (9B206) will not sync with new Itunes version 12.0.1.26. Can anyone help

What exactly happens when you try to sync?
Does iTunes see the iPod?
Was the iPod previous synced to another iTunes library/computer?
Have you successfully synced from this iTunes library/computer before?
If so have you done anything like update iTunes on the computer since it last successfully synced?
Do the songs play in iTunes?
Does any media now sync to the iPod?
Do you have the right boxes checked to sync?
iTunes: Syncing media content to iOS devices and iPod
Try syncing using the manual method
Managing content manually on iPhone, iPad, and iPod
If iTunes does not see the iPod:
iOS: Device not recognized in iTunes for Mac OS X
Or
See
iOS: Device not recognized in iTunes for Windows
- I would start with
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
or
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
- Then do the other actions of:
iOS: Device not recognized in iTunes for Windows
paying special attention to item #5
- New cable and different USB port
- Run this and see if the results help with determine the cause
iTunes for Windows: Device Sync Tests
Also see:
iPod not recognised by windows iTunes
Troubleshooting issues with iTunes for Windows updates
- Try on another computer to help determine if computer or iPod problem

More detail and a reply for the CQ50 - 130US will not boot with 8gb ram post

The specs, on the web site say that the max memory supported is 3GB DDR2 because the notebook was built with the OS Vista(32 bit) installed so that’s why the manual has the 3 GB max. memory supported limit. The 32 bit OS can’t address memory over 3.12 GB. To my mind that is not a spec. but rather a tech. writer who made a mistake and copied the sales literature. With Windows 7(64 bit) Pro. installed the OS can address up to192GB of memory if the system supports it. Other Compaq and HP Notebooks can deal with 8GB of memory installed. That’s why I would think HP’s could easily fix this with a patch or use one of their other BIOS’s.
The difference between 4GB and 6GB is that with 6GB system runs faster and the display quality has improved. I have set the cache size to large and the executive paging is set to off in the registry. The menu(System Properties - Performance Options – Advanced – Virtual Memory) is set to automatically manage the paging file size.

You should keep it in the original; thread you started.
http://h30434.www3.hp.com/t5/Notebook-Hardware/CQ50-130US-will-not-boot-with-8gb-ram/m-p/490157

MBP15 1.83 GHz Will Not Boot With 3GB Upgrade

I'm trying to increase my MBP's ram to the 3GB limit. This is a 1.83 GHz 15" model.
It will not boot with 2GB & 1GB sticks of identical mfg & specs. It will boot with one or the other...
Any ideas?
Thanks,
Stradioti

Hi
according to the Apple specs for the 1.83GHz mbp's - 2Gig of memory is the limit......
512MB (single SODIMM) of PC2-5300 (667MHz) DDR2 memory on 1.83GHz configuration; and 1GB (single SODIMM) on 2.0GHz configuration; two SODIMM slots support up to 2GB
Crucial Memory says the same.

I forgot my password and ipod will not sync with new computer

I forgot my password and ipod will not sync with new computer

You'll need to connect the iPod Touch to your iTunes library in recovery mode and restore it factory settings. There is no other way.
Here are instructions for getting your iPod touch into recovery mode.
http://support.apple.com/kb/ht1808
B-rock

X79A-GD65 (8D) will not boot with 4930K or 3930K

Short version:
My system will not boot but gets stuck at "09 Power on South Bridge Initialization"
Detailed description:
I just bought this system and am when I tried to start it it got stuck at "09 Power on South Bridge Initialization". I have removed everything that is not necessary (gfx-card, HDDs, etc.) and only have the CPU and one memory stick inserted (in slot 1 as per the manual). I have also unplugged and put back all power cables from the PSU several times. I have also tried using BIOS A and B.
As I read on this forum that a BIOS update was needed for IVY-Bridge CPUs I bought a 3930K today to see if I could get the system up and running but it still gives me the same error code.
My board serial number is 601-7760-010B1312109204, assuming it is manufactured 1312 = December 2013.
I don't know the BIOS revision as I have never managed to get past the 09 status code.
Any ideas on what the problem could be?
Bought this monster PC as I have a delivery for a client in need of some RAM-heavy processing, so am really starting to feel stressed out about this by now.
Thanks in advance!
System details:
- MSI X79A-GD65 (8D) X79 S-2011 ATX
- INTEL CORE I7 4930K 3.4GHZ 12MB S-2011
- INTEL 530 80GB SATA SSD MLC RESELLER KIT
- INTEL 530 480GB SATA SSD MLC BULK (4 of these)
- FRACTAL DESIGN INTEGRA R2 750W
- ASUS GEFORCE GT 210 1GB DDR3 PCI-E VGA/DVI/HDMI SILENT
- KINGSTON 64GB 1600MHZ DDR3 ECC REG CL11 DIMM (4X16GB) W/TS (two kits, 128GB in total, don't really need ECC but that's what I could find needing 16GB sticks)

even compared to just 10 years ago sales staff have became really dumb as there just hiring people who do not care about anything as long as they get there cut of a sale (usually all they know is basic Consumer parts they stock) and nearly non of them unless they specialize in that level of equipment will have 0 idea what they work with on a pro level part (ECC memory tends to be used on servers and Professional workstations so if they do not use that type of gear then they probably have no idea what ECC really is at all)!
also in that time some major things have happened especially with computer parts like the memory controller moved from the Chipset to the CPU same with the SATA controller , onboard GPU (thats now on the CPU and some have it some don't) and alot of other things and I guess that the people you dealed with had no idea the memory support has very little to do with the board (all the board can do is have BIOS Timing sets now and lists of parts it supports) and is now to do with the CPU alot more as it has the important stuff on it (there very close to a SOC (System On Chip) now)!
if you plan on building another computer remember to do some research yourself before you get a CPU as it is nearly the most important thing of all and they have different features tied to them and do not expect sales guys to have a idea unless there also a Technical support staff member too and work on computers that are of the same class your trying to make and have at least used the same level gear (usually if your doing something like that find a friend who is a computer nerd tell him what your trying to do and get him to help you choose all the parts)!
let me know how it goes when you get the Xeon and have it installed?

Airport extreme will not boot with USB hard disk plugged in.

Hi there,
I'm using the Airport Extreme Base Station, and I find that if I have a USB hard disk plugged into it, it will not boot up, it only hang-ups with an amber light, and stays there indefinitely. It's not a terrible issue because it can be overcome by unplugging the disk then rebooting, but it's irritating, especially when I'm not home and there is a power temporary outage and my wife can no longer access the internet or I can no longer access my disks over the internet.
Is there a solution to this problem?
Thanks,
Marc

I'm going to have to replace the unit, as I'm unable to turn off DHCP services, which is wreaking havoc on my server based environment.
Considering THIS issue *AND* the major DHCP show stopper, frankly, I'm debating etiher the fire pit or tossing the damned thing into the intersection and watching it be reduced to the trash that it is.
Either way, there'll be 7 feet of pack ice in **** before I buy another Apple networking product.
I'll decide later, with a jaundiced eye, regarding our XServe unit. Might reformat it to Linux...

T61 will not boot with nvidia quadro 140m driver

Hi all,
A couple of weeks ago, after allowing MS update to install some FTDI driver updates, my system will not boot up and hangs shortly after the initial vista loading screen. The screen goes black with some HD activity and eventually reboots. After trying a couple of restore points with no luck, I started to remove the latest driver updates and other software to my system again with no luck.
If I uninstall the nvidia driver and use the Standard VGA driver, it will boot and come up properly. I've done a bunch of web searches and searches on this site and can't find my exact circumstances. Its hard to believe that it could be a hardware issue since it started after a software update, but since it hasn't been a problem for anyone else, I'm just not sure at this point.
I've tried earlier versions of the nvidia driver, removing other drivers and services trying to find a coincidence, but nothing seems to work. I'm kind of at a loss at this point. Does anyone have some suggestions?
Thanks in advance,
Dave

More info on my system:
OS Name    Microsoft® Windows Vista™ Business
Version    6.0.6001 Service Pack 1 Build 6001
System Model    6459CTO
System Type    x64-based PC
Processor    Intel(R) Core(TM)2 Duo CPU     T8300 @ 2.40GHz, 2401 Mhz, 2 Core(s), 2 Logical Processor(s)
BIOS Version/Date    LENOVO 7LETC5WW (2.25 ), 11/14/2008
SMBIOS Version    2.4
Installed Physical Memory (RAM)    4.00 GB
Also, does anyone know if using the Standard VGA Display driver without problems on this system means that the video card hardware is working? In other words, I'm trying to rule out a hardware problem with my nvidia quadro 140m card, so if the system works fine with the standard vga driver, would that mean the hardware on the card is ok?
Thanks,
Dave

System will not boot with Seagate 3Tb expansion drive plugged in.

I have a HP Pavilion HPE h8- 1214 Desktop , I recieved a Seagate 3TB expasion drive as a gift but when plugged in, the system will not boot. It turns on but thats it. It never gets to the boot sequence. I have it plugged into the top 3.0 usb slot and have tried all of the other slots as well with no sucess. But if I leave it unplugged the system boots right up. I can then plug it in and it works fine. I have plugged it into my wifes HP All- In- One and it boots fine and works. I have a WD 2TB drive that works fine as well on my system . I have searched Segates support for hours and all they say is to change the boot sequence. Have tried that, no go. What they dont get is no matter what I do if that drive is plugged in it never gets as far as booting and reading the boot sequence. Please help. Thank you!

Hi NcBunky,
Are you using Win 7 64 bit? Did you update the Texas Instruments (TI) USB 3.0 XHCI Host Controller?
I have an H8 1380t PC. Updated the TI USB 3.0 driver and had the same problem.
When booting the PC with the USB 3.0 external drive connected to the PC the PC would not boot. When booting the PC with only the mouse, keyboard, and a USB 2.0 external drive attached the PC would boot. Once booted you could attach the USB 3.0 drive and it worked fine.
Solution was to roll back (reinstall) the TI USB 3.0 XHCI Host Controller to the original factory installed driver.
System now boots with the external USB 3.0 drive attached.
Jaco
****I am not an HP employee****
Please give a" Kudos" if advice received is relevant or" Accept as Solution" if your problem has been solved.
+++++++++++++++++++++++++++++++++++++++++++++++++++++
H8 1380t CTO, Intel i7 3820
16 GB DDR3
Pegatron Motherboard- IPIWB-PB (Pittsburgh), Radeon HD 7570 1GB. Win 7 Home Premium upgraded to Windows 8.1 Pro.
Envy Phoenix 810-150se, Intel i7 4820k
16 GB DDR3
Pittsburgh2 Mainboard, NVIDIA GTX 645- 2GB GDDR5. Win 8.1 Pro.
HP 560z CTO AMD Phenom II X6 1090T
16 GB DDR3.
Radeon HD 6570
Win 7 Home Premium upgraded to Win 7 Pro.
HP ENVY 17t-j000 CTO Quad Edition Notebook. I7 4702mq
12 GB DDR3
Nvidia Graphics
Win 8 Pro
Errare humanum est.

T410 will not boot with new SSD

Similar Messages

Maybe you are looking for