T420 Build Issues

My T420 (4177 CTO) is still under factory warrenty, so it is less than a year old. There are two build issues that I have so far ignored, but I am wondering if they are "normal."
The laptop does not rest level on a flat surface. Three of the rubber grips on the underside touch the surface, but the front, left grip is so far off the surface that you can slide a piece of paper under it without resistence. When I rest my left hand on the palmrest, the chassis audibly "creaks" and visibly moves as the rubber grip comes to rest on the surface.
Just recently permanent friction marks have appeared on the left half of my screen, clearly caused by months of rubbing against the keyboard. I have tried cleaning them per Lenovo's instructions, to no avail.
I am beginning to think that the chassis is deformed, and that it has been this way since I received the machine. Both issues have been present since the start, but the marks on the screen could be easily wiped off until recently.
Are these issues "normal," or am I suffering from a defective machine?
Thanks for your opinion or any information!

My T420 has spent its life in a backpack, as did the T400 and T61 before it. I've never noticed this kind of problem.
Have you taken a careful look at the sides of the laptop to verify that the keyboard bezel and bottom plastic are snapped together correctly? Any gaps or bulges?
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Similar Messages

Week 25 Whine, Heat, Build Issues Finally Fixed!

I received a week 25 MBP yesterday and I can say that Apple has finally got it right.
I have had numerous problems with previous machines ranging from bad video cards, dropped wifi connections, broken latches and the infamous heat and whine problems.
This new machine is absolutely perfect. Here are my observations:
- Absolutely no whine under battery or while plugged in (even when the machine is idle)
- Heat does not exceed 42c on normal tasks and the machine idles at 37c-40c.
- The case is barley warm to the touch.
- Wifi range and performance is excellent.
- No cosmetic build issues such as warped lid or broken latch.
I wholehartedly recommdend people who have been waiting to go ahead and make your purchases.

it appears apple has fianlly figured out new power cicutry for the mobo to cpu that no longer whines. there's an article about a macintouch editor (or writer i forget, he works for them) who just got it back with a letter, and no longer has any whine, at all.
I'm going to talk to my apple place this week adn see if i can get htem to replace it again, its clearly a whine on my new logic board, so i don't see why they wouldnt - i'll jsut tell them ti is loud as they know, just hopw they wont say something like 'no, we already did it'.
anyway, good luck everyone ill wait a week ro so to try to help get the very newest rev of mobo
edit: forgot the link! http://macdailynews.com/index.php/weblog/comments/10076/

Release Build Issue

Hello!
I'm stuck on something pertaining to my release build. It's not working. I know there could be a lot of reasons for this, most related to path dependencies within my code. In my troubleshooting, however, I've stumbled across an issue that I think is at the root of the problem. I'm hoping someone has a solution!
Here it is:
I'm using Flex Builder 3, and it's an AS3 project. Running the project is no problem. Works great from the bin-debug folder. As soon as I pull the files in the bin-debug folder into another folder, however, it no longer runs. I'm doing this in the most basic way possible. Here are the steps I'm taking:
1. create a new folder at the same level as bin-debug. Calling it, creatively, bin-debug2.
2. copying all the files in bin-debug and pasting them in bin-debug2.
3. opening my browser and surfing to bin-debug/project.html - works perfect.
4. opening my browser and surfing to bin-debug2/project.html - doesn't work.
How is it possible for the exact same files not to work just because the parent folder has a different name?
I believe answering this will solve my release build issues.
Thanks!!

Hi Greg,
Thank you for taking time to help me troubleshoot this.
Running the bin-debug version of the projects main .html page in a browser works. Meaning, the page loads, I see the default background color I've set in the compiler, and the opening animation starts.
Then I copy and paste all of the files in bin-debug to bin-debug2. Try running the exact same .html file. The page opens in the browser and I see the default background color I've set in the compiler. The opening animation never starts.
Thanks,
Jake

T420s Optimus Issues

Greetings,
I have a T420s that is an Optimus capable model. I am trying to achieve a 3 monitor set up and I have the correct docking station (the plus model), however, my optimus does not work properly, I have a monitor hooked up to almost every port in hopes of detecting them (2 DVI, 1 VGA, 1 Display port):
1) In Optimus Graphics Mode (Via the BIOS), when I log in to Windows, I can open up Device manager and watch the NVS 4200M drop off of the device manager and either give a generic graphics card name and indicate there is an issue with it or not appear at all
A) The NVIDIA Control panel will not load as it indicates I do not have an NVIDIA GPU installed
B) No NVIDIA Context menus are available
2) In Discrete Graphics Mode (Via the BIOS), the Intel GPU does not appear in device manager, however the NVIDIA GPU Works fine
A) NVIDIA Optimus Graphics settings do not appear under "Manage 3D Settings" on the NVIDIA control panel
B) I do not have a "View" menu on NVIDIA control panel from which I can check the feature to add GPU selection to the
right click context menu when dealing with applications
C) I somewhat expect this to be the behavior using Discrete Graphics mode
3) In integrated graphics mode (via the bios), the NVIDIA GPU does not appear under device manager, however the Intel GPU works fine.
A) I assume this is the correct behavior
NVIDIA Details:
NVS 4200M
NVIDIA Control Panel Version : 4.3.980.0
NVIDIA Driver: 276.58
Intel Details:
HD3000
I've reinstalled all GPU related drivers for both cards, and reinstalled using the generic package that lenovo provides. This has not corrected the issue. I used the ones dated April 2012, from this site.
I've reinstalled everything again, attempted to install the drivers directly from NVIDIA and it states I must install an Intel driver first before allowing me to proceed
Any ideas?

I don't think its in the list it may be somewhere else. Only current ones are listed usually. Go to the support website and see what is listed for your machine type and build number.
You may have to call support but why did the OEM image get replaced if there wasn't a customized tested image made for it. Clearly if you need this driver as well you're just starting with collection of likely issues that they may not be able to resolve. Support may say to put the image back on and then call if you have problems.
Not knowing what was done requires hands on by a seasoned tech who may be able to resolve it in time. There are machine specific which need to addressed and without them installed and the lenovo tools and Thinkvantage installed you could be in for long weekend working on it.
Good luck.
T520 Model 4239 Intel(R) Core(TM) i7-2860QM CPU @ 2.50GHz
Intel Sandy Bridge & Nvidia NVS 4200M graphics Intel N 6300 Wi-Fi adapter
Windows 7 Home Prem - 64bit w/8GB DDR3

Report Service And Report Builder Issue

SQL SERVE 2012
In our web site project we use ReportingService2010 Methods to show and operate folder and report which stored in Report Service, in our project configuration file, we use windows authentication mode for Report Service.
In requirement
User can show and operate folder “A” and folder “B” (we can create and delete report or folder) in web site.
User can’t use “Report Builder” to save reports which created by Report Builder to folder “B”, Reports which created by Report Builder only can be saved in folder “A”.
[User click “Report Builder” button in our web page to start Report Builder, use
“Report Builder” to create report, if user want to save report, we need to hidden folder “B” in “Report Builder” or we need to remove some operate right from folder “B”.]
We have no solution for this requirement, could you help us?

Thank you for your replay, but I don't understand it very clearly.
Please check the first requirement:
User can show and operate folder “A” and folder “B” (we can create and delete report or folder) in web site.
For example, I login my PC with account "lfang", in report server, we grand "Browse" permission on both folder and grand only "Publish" permissions for folder "A", report builder can't save report into folder "B",
it's correct.
But our web site has create report function, that means in our web site we want to create report for both folder "A" and "B", that is the issue, if we don't give "Publish" permissions to folder
"B", we can't create report in our web site.
Is there any method to run "report builder" use specified account? then we can only give folder "A" "Publish" permissions with specified account.

Multiple columns (named the same originally) and mapped to the same lookup table are causing a Cube Build issue

Hey folks, looking for some insight here.
I've an implementation that contains some custom Enterprise columns mapped to lookup tables. In the instance I'm working with now, it looks like there was/is an issue with one of those columns. In this scenario, I have a column named
ProjectType, created initially with that name, mapped to a lookup table. This field's name was then changed to
Project Type. After that, it looks like another column was created, also called
ProjectType. So now, we have what I would have originally thought was two distinct columns, even though the names used are the same.
Below is the error we're currently getting during the Cube Build Process...
PWA:http://ps2010/PWA, ServiceApp:Project Web App, User:DOMAIN\user, PSI: SqlException occurred in DAL: <Error><Class>1</Class><LineNumber>1</LineNumber><Number>4506</Number><Procedure>MSP_EpmProject_OlapView_B8546719-4D4C-473A-84B1-89DEDA2307E0</Procedure>
<Message> System.Data.SqlClient.SqlError: Column names in each view or function must be unique. Column name 'ProjectType' in view or function 'MSP_EpmProject_OlapView_B8546719-4D4C-473A-84B1-89DEDA2307E0' is specified more than once. </Message>
<CallStack>
at System.Data.SqlClient.SqlConnection.OnError(SqlException exception, Boolean breakConnection)
at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj)
at System.Data.SqlClient.TdsParser.Run(RunBehavior runBehavior, SqlCommand cmdHandler, SqlDataReader dataStream, BulkCopySimpleResultSet bulkCopyHandler, TdsParserStateObject stateObj)
at System.Data.SqlClient.SqlCommand.FinishExecuteReader(SqlDataReader ds, RunBehavior runBehavior, String resetOptionsString)
at System.Data.SqlClient.SqlCommand.RunExecuteReaderTds(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, Boolean async)
at System.Data.SqlClient.SqlCommand.RunExecuteReader(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, String method, DbAsyncResult result)
at System.Data.SqlClient.SqlCommand.InternalExecuteNonQuery(DbAsyncResult result, String methodName, Boolean sendToPipe)
at System.Data.SqlClient.SqlCommand.ExecuteNonQuery()
at Microsoft.Office.Project.Server.DataAccessLayer.DAL.SubDal.ExecuteStoredProcedureNoResult(String storedProcedureName, SqlParameter[] parameters) </CallStack> </Error>
I've tried deleting the one column, but the build still gives the above error.
Any thoughts as to how the above could be resolved?
Thanks! - M
Michael Mukalian | Jan 2010 - Dec 2010 MVP SharePoint Services | MCTS: MOSS 2007 Configuration | http://www.mukalian.com/blog

We tried taking it out of the cubes, and it builds fine. The challenge we're having is in building the cubes with that custom field "ProjectType". It's as if the cubes still hold some reference to it even when it's deleted.
Since the OLAP View ('MSP_EpmProject_OlapView_{guid}') is recreated, would it be as simple as deleting that View, and trying to recreate?
Thanks - M
Michael Mukalian | Jan 2010 - Dec 2010 MVP SharePoint Services | MCTS: MOSS 2007 Configuration | http://www.mukalian.com/blog

Labview 2012 Installer builder issues with Windows 7 64 bit

I have a clients project application program I am working on and am having a lot of trouble getting installed applications to work on Windows 7 properly. The Labview Installer sets the default installation directory to "c:\Program Files\" on Windows Xp and on Windows 7 64bit this defaults to "C:\Program Files (x86). When I install the application on Windows 7 and run it, because Windows 7 64 bit unreasonably protects this directory and every folder under it, if you try to write file to any subdirectory under it (like a reports directory), windows 7 will not let the file write to the directory and the file(s) disappear and you get permission errors. This has been difficult to address. Even logging in as administrator, I have difficulty changing the folder permissions. In addition, when I am in the file write process, if the default directory is coded to come up in the file Open/Save dialog, will not properly
go to and display these protected directories. So thinking that OK, I'll just chage the install directory to something direct to the C: drive and not the Program Files (x86) directory, so I have better control of the folder permissions. Now the Installer build gives errors. It built, but the install fails. Looks like National did not test this for Windows 7 very well. I have run into just about every issue possible with Windows 7 and Labview. Clearly Labview was not very well tested with Windows 7 6 bit. I do not have the Internet toolkit added to the application, only the VISA 5.2 driver. Anyone else having application issues with Labview and Windows 7 and have ideas how to work around this??
Attachments:
BuildErrors.txt ‏11 KB

It's no NI's fault and has nothing to do with 64 Bit either. It is something MS changed starting with Vista, namely tightening security of the whole system to a similar level as was usual on more professional OSes like Unix 20 years earlier. A user has not rights anymore to write into the location where applications are installed. This is for one reason to protect installed applications from being modified by malicious code.
Instead every application should write its runtime data in one of the user writable loacations such as the user's Documents directory for data files, or in the user's or the machine's configuration directory for configuration settings. For single installations you could always set the directory which your application got installed into to be user writable by changing the rights of that directory afterwards but for applications that get installed on normal user computers this is a VERY hacky and discouraged move. Same about installing your application into the root of your system drive. I think it was an oversight by MS to not protect that directory too from user modifications, but was most likely unavoidable to allow DOS application installations to still work.
LabVIEW has functions to retrieve a whole bunch of those preconfigured and user writeable locations and you really should change your application to make use of those locations, instead of trying to write into the installation directory or installing the application into the root location of the system drive, if you want to be compatible with Windows Vista/7/8.
Windows 7 also requires for a number of actions such as installing programs or drivers so called elevated rights. This means that even if you are logged in as administrator you have to explicitedly provide the admin password again to be able to perform the action. This can be done by starting the program as administrator, when this is available in the right click pop-up menu, and is also sometimes done automatically for applications that Windows determines to need those rights such as setup programs for installations.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

Multi Source execution plan build issue

Hi,
I am trying to create/build a multi source (homogenous) execution plan in DAC from 2 containers for 2 of the same subject areas (Financial Payables) from 2 different EBS sources. I successfully built each individual subject area in each container and ran an executin plan for each individually and it works fine. Now I am trying to create 1 execution plan based on the DAC steps. So far I have done the following:
- Configured all items for both subject areas in the DAC (tables, tasks, task groups, indexesconnections, informatica logical, physical folders, etc)
- Assigned EBS system A a sifferent priority than EBS system B under Setup->Physical Data Sources
- I noticed that I have to change the Physical Folder priorities for each informatica folder (SDE for Container A versus SDE for Container B). I assigned system A a higher priority
- Build the Execution plan..
I am able to build the execution plan successfully but I have the following issues/questions:
1) I assumed that by doing the steps above..it will ONLY execute the extract (SDE) for BOTH system containers but only have ONE Load (SIL and PLP)..and I do see that the SDEs are ok..but I see the SIL for Inder Row in RunTABLE running for BOTH...why is this? When I run the EP...I get an unique constraint index error..since its entering two records for each system. Isnt the DAC suppose to include only one instance of this task?
2) When I build the execution PLAN, it is including the SILOS and PLP tasks from BOTH source system containers (SILOS and PLP folders exist in both containers)...why is this? I thought that there is only one set of LOAD tasks and only SDE are run for each (as this is a homogenous load).
3) What exactly does the Physical folder Priority do? How is this different than the Source System priority? When I have a multi source execution plan, do I need to assign physical folder priorites to just the SDE folders?
4) When we run a multi source execution plan, after the first full load, can we somehow allow Incremental loads only from Container A subject area? Basically, I dont want to load incrementally from source sytem A after the first full load.
4) Do I have to set a DELAY? In my case, my systems are both in the same time zone..so I assume I can leave this DELAY option blank. Is that correct?
Thanks in advance
Edited by: 848613 on May 26, 2011 7:32 AM
Edited by: 848613 on May 26, 2011 12:24 PM

Hi
you are having 2 sources like Ora11510 and OraR1211 so you will be having 2 DAC containers
You need these below mandatory changes
for your issue
+++++++++++++++++++++++++++++++++
Message: Database errors occurred:
ORA-00001: unique constraint (XXDBD_OBAW.W_ETL_RUN_S_U2) violated while inserting into W_ETL_RUN_S
You need to Inactivate 2 tasks in R12 container.
#1 Load Row into Run Table
#2 Update Row into Run Table
+++++++++++++++++++++++++++++++++
There are other tasks that has to be executed only once
(ie Inactivate the Below in One of the container)
SIL_TimeOfDayDimension
SIL_DayDimension_GenerateSeed
SIL_DayDimension_CleanSeed
SIL_TimeOfDayDimension
SIL_CurrencyTypes
SIL_Stage_GroupAccountNumberDimension_FinStatementItem
SIL_ListOfValuesGeneral_Unspecified
PLP_StatusDimension_Load_StaticValues
SIL_TimeDimension_CalConfig
SIL_GlobalCurrencyGeneral_Update <dont Inactivate this> <check for any issues while running>
Update Parameters <dont Inactivate this> <check for any issues while running>
+++++++++++++++++++++++++++++++++++
Task :SDE_ORA_EmployeeDimension_Addresses
Unique Index Failure on "W_EMP_D_ADR_TMP_U1"
As you are load from 11.5.10 & R12 , for certain data which is common across the systems the ETL index creation Fails.
Customize the Index Creation in DAC with another unique columns (data_source_numID).
++++++++++++++++++++++++++++++++++++
Task :SDE_ORA_GeoCountryDimension
Unique Index Failure on "W_GEO_COUNTRY_DS_P1 " As you are loading from 11.5.10 & R12 , for certain data which is common across the systems the ETL index creation Fails.
Option1) Customize the Index Creation in DAC with another unique columns (data_source_numID)
++++++++++++++++++++++++++++++++++
This changes were mandate
Regards,
Kumar

Folio Builder issues

Hi,
We are having troubles uploading to Folio Builder. We've tried different computers, different networks, different InD versions (CS6, CC, CC 2014).... we can only get 4-6 articles in on a multiple article upload before it crashes InDesign (no error message). Is anyone else having issues?
Any help greatly appreciated. Thanks

I am experiencing the exact same issue. Trying to update or upload articles and it just crashes out. I also have some bizarre flickering box appearing in the middle of my folio builder window!? Yesterday, initially I was getting to upload/update about 5 articles before it would crash out and by the end of the day I couldn't get any.

Build Issue

Hi Experts,
We are having issue with the local build of DC in NWDS.
We are having a Track which contains few SCs, now a new SC has been created and further new DCs in the newly created SC. Now when I am trying to build the new DC it is giving me the below error.
No 'default' JDK defined, will use running VM.
Error: com.sap.tc.buildplugin.util.BuildPluginException: No 'javac' found for JDK home path 'C:\Java\SAPJVM6\sapjvm_6\jre'.
    at com.sap.tc.buildplugin.JavaMacroContextProvider.setupJavaCompiler(JavaMacroContextProvider.java:276)
    at com.sap.tc.buildplugin.JavaMacroContextProvider.setupJavaEnvironment(JavaMacroContextProvider.java:186)
    at com.sap.tc.buildplugin.JavaMacroContextProvider.execute(JavaMacroContextProvider.java:40)
    at com.sap.tc.buildplugin.PrepareContextBuildStep.prepareTechnologySpecificData(PrepareContextBuildStep.java:193)
    at com.sap.tc.buildplugin.PrepareContextBuildStep.setupBuildFileCreatorContext(PrepareContextBuildStep.java:95)
    at com.sap.tc.buildplugin.PrepareContextBuildStep.execute(PrepareContextBuildStep.java:56)
    at com.sap.tc.buildplugin.DefaultPlugin.handleBuildStepSequence(DefaultPlugin.java:196)
    at com.sap.tc.buildplugin.DefaultPlugin.performBuild(DefaultPlugin.java:168)
    at com.sap.tc.buildplugin.DefaultPluginV3Delegate$BuildRequestHandler.handle(DefaultPluginV3Delegate.java:66)
    at com.sap.tc.buildplugin.DefaultPluginV3Delegate.requestV3(DefaultPluginV3Delegate.java:48)
    at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
    at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
    at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
    at java.lang.reflect.Method.invoke(Method.java:597)
    at com.sap.tc.buildtool.v2.impl.PluginHandler2.maybeInvoke(PluginHandler2.java:350)
    at com.sap.tc.buildtool.v2.impl.PluginHandler2.request(PluginHandler2.java:99)
    at com.sap.tc.buildtool.v2.impl.PluginHandler2.build(PluginHandler2.java:73)
    at com.sap.tc.buildtool.PluginHandler2Wrapper.execute(PluginHandler2Wrapper.java:59)
    at com.sap.tc.devconf.impl.DCProxy.make(DCProxy.java:1750)
    at com.sap.tc.devconf.impl.DCProxy.make(DCProxy.java:6004)
    at com.sap.ide.eclipse.component.provider.actions.dcproject.BuildAction.buildDCsForDevConfig(BuildAction.java:307)
    at com.sap.ide.eclipse.component.provider.actions.dcproject.BuildAction.access$200(BuildAction.java:58)
    at com.sap.ide.eclipse.component.provider.actions.dcproject.BuildAction$1.run(BuildAction.java:212)
    at org.eclipse.jface.operation.ModalContext$ModalContextThread.run(ModalContext.java:101)
Error: Build stopped due to an error: No 'javac' found for JDK home path 'C:\Java\SAPJVM6\sapjvm_6\jre'.
I have checked the build variant for the track in SLD and it is maintained as :
com.sap.jdk.home_path_key = JDK1.5.0_HOME.
I have also maintained the Installed JRE in NWDS as JDk 1.5.
Strange part is now if I create the DCs in the old(already present) SC it is working fine and getting built without any error.
Please help!
Regards,
Pankaj

what's the version of your nwds?
you have specify the jdk path not the jre
put the following in your ini file which is located in the nwds installation folder
-vm
C:/jdk1.6x86/bin/javaw.exe (your jdk path)
the following configuration should also help.

Dispatching GridSelectionEvent throw exception at runtime - A build issue with FB 4.5

This is a strang probelm I am facing with.
My code dispatches GridSelectionEvent after setting girds' selected item in one logic path. Following is code lines -
myDataGrid.selectedItem = instanceTag;
myDataGrid.dispatchEvent(new GridSelectionEvent(GridSelectionEvent.SELECTION_CHANGE));
Flash player throws following error on above statements encounter -
TypeError: Error #1009: Cannot access a property or method of a null object reference.
    at spark.accessibility::DataGridAccImpl/eventHandler()
    at flash.events::EventDispatcher/dispatchEventFunction()
    at flash.events::EventDispatcher/dispatchEvent()
    at mx.core::UIComponent/dispatchEvent()
I am saying it is a strang for me because when I use swf file generated by Flex Builder (4.5)'s export to release build, it does not throw error and code works fine as expected.
But, when I user swf file generated by Ant script, I face the above issue.
The Flex builder settings is as shown in following image -
Ant mxmlc script is as follow -
<mxmlc
           file="${basedir}/src/AppMonConfigWizard.mxml"
            static-rsls="false"
           keep-generated-actionscript="false"
           output="${basedir}/bin-release/AppMonConfigWizard.swf" >
     <locale>en_US</locale>
      <load-config filename="${FLEX_HOME}/frameworks/flex-config.xml"/>
      <source-path path-element="${FLEX_HOME}/frameworks"/>
      <source-path path-element="${basedir}/src/locale/{locale}"></source-path>
      <compiler.library-path file="${basedir}/../wizard_framework/bin/wizard_framework.swc" append="true"/>
     <compiler.library-path file="${basedir}/../../utils/bin/utils.swc" append="true"/>
      <include-resource-bundles>ErrorMessages</include-resource-bundles>
      <include-resource-bundles>Strings</include-resource-bundles>
</mxmlc>
As mentioned earlier that following statements cause exception -
     myDataGrid.selectedItem = instanceTag;
     myDataGrid.dispatchEvent(new GridSelectionEvent(GridSelectionEvent.SELECTION_CHANGE));
If I change it to
     myDataGrid.setSelectedIndex(<some index value>)   /*selectedItem replaced with setSelectedIndex*/
     myDataGrid.dispatchEvent(new GridSelectionEvent(GridSelectionEvent.SELECTION_CHANGE));
it does not throw exception. I would like to mention that myDataGrid.selectedItem = instanceTag; does sets the selected item but then in that case issue arises when dispatching event.
I my application, similar statemetns were lot at many places (as there were no such issue with SDK 3.1 which was using earlier) so instead of making changes there, it would be better to imitate the build that Flex builder uses when exported the release build.
Thanks in advance,
Prithveesingh Zankat.

Solved it: had set the only public surface contracts checkbox by mistake and the cosntructor was protected...
Luis Abreu

LV2010 SP1 Installer Build Issue- Cannot find the file it need on requesyed disk

I am migrating a project from LV8.6.1 to 2010SP1 and had issues building the installer that I was finally able to overcome, but something is amiss with the process.
Brand new development PC, running XP SP3, fresh install of LV2010SP Dev Suite and also installed VDM2010 SP1 (even though the project does not use any vision modules).
-          Copied 8.6.1 project to the PC, did a mass compile of it and built the exe from scratch without issues.
-          Now it’s time to build the installer from scratch. Additional Installers were:
LV2010 RTE, MAX 4.7, NI-DAQmx Full App Devel Support 9.2.3, and NI-VISA 5.03.
-          Get the message that it will need some disks to build it which I have on hand:
Dev Suite DVD#2, Drivers DVD, and VDM DVD (huh, why VDM?)
-          The installer build progresses through the first two disks fine but will not find the files it needs on the VDM DVD (it is looking for “NI System Components”).
-          Installer build bails out with a message box and no installer is created (1st attachment). The installer logs are also attached.
-          Try the build process gain, same result.
-          Copied the VDM DVD to my hard drive and point it to that folder to get the files, same result.
-          Try again saying I don’t have the disks on hand. It lists some alternate disks to use but to get all the files it still wants the VDM DVD to complete it. Not much use, the build still fails.
-          Try one last time again selecting that I don’t have the disks on hand. I now notice that the folder the VDM was copied to on the hard drive is an option to select. Select that one and lo and behold the installer is built successfully.
So I guess it boils down to:
            - Why does it need the VDM DVD when there are no components of vision used?
            - Why can’t the installer find the files it needs on the VDM DVD or a copy of the DVD on the hard drive?
            - Why will it only work if I choose that I do not have the disks and point it to a copy of the DVD that resides on the hard drive?
-AK2DM
~~~~~~~~~~~~~~~~~~~~~~~~~~
"It’s the questions that drive us.”
~~~~~~~~~~~~~~~~~~~~~~~~~~
Attachments:
MessageDuringVDMCopyForInstaller2010.JPG ‏127 KB
TowersSPCv225Installer_build.log ‏3126 KB
TowersSPCv225Installer_edit.log ‏915 KB

Che:
It gave no specific indication of what it was looking for, the only message that came up was in the screenshot jpg I originally posted.
The only other vague clue I had was it needed NI System Component from the VDM DVD.
Does not make sense that it required the VDM DVD since there were no vision components in the project. I presume it would have taken VISA off of the Dev Suite DVD's.
I can't replicate the problem since I had the build cache the system components required for the project. I'd rather not start deleting folders at this point since I have a viable installer at this time (after many hours of troublshooting expended).
Thanks
-AK2DM
~~~~~~~~~~~~~~~~~~~~~~~~~~
"It’s the questions that drive us.”
~~~~~~~~~~~~~~~~~~~~~~~~~~

WLI Application Build issues - The apt.factory.path was not set

Hi,
I have been trying to execute the Workshop exported Ant Script on Remote machine. In my local machine where i have access to workshop i am able to run the ant script whithout any issues. But when i try the same script on Remote machine (unix) I ma getting the below exception.
In my application, there are two projects. One web application and one EJB project, and i am trying to makr Ear file out of this.
If any of you have faced this issue or if you have any inputs pl help me out.
/opt/buildserver/home/e0271019/WFM_1031_migrated_Source/Migrated_Code_With_AntScript/wfm/build.xml:340: The following error occurred while executing this line:
/opt/buildserver/home/e0271019/WFM_1031_migrated_Source/Migrated_Code_With_AntScript/wfm/build.xml:690: The apt.factory.path was not set, but the beehive annotation processors must be on the apt factory path.
at org.apache.tools.ant.ProjectHelper.addLocationToBuildException(ProjectHelper.java:508)
at org.apache.tools.ant.taskdefs.MacroInstance.execute(MacroInstance.java:397)
at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:288)
at sun.reflect.GeneratedMethodAccessor1.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at org.apache.tools.ant.dispatch.DispatchUtils.execute(DispatchUtils.java:106)
at org.apache.tools.ant.Task.perform(Task.java:348)
at org.apache.tools.ant.Target.execute(Target.java:357)
at org.apache.tools.ant.Target.performTasks(Target.java:385)
at org.apache.tools.ant.Project.executeSortedTargets(Project.java:1337)
at org.apache.tools.ant.Project.executeTarget(Project.java:1306)
at org.apache.tools.ant.helper.DefaultExecutor.executeTargets(DefaultExecutor.java:41)
at org.apache.tools.ant.Project.executeTargets(Project.java:1189)
at org.apache.tools.ant.Main.runBuild(Main.java:758)
at org.apache.tools.ant.Main.startAnt(Main.java:217)
at org.apache.tools.ant.launch.Launcher.run(Launcher.java:257)
at org.apache.tools.ant.launch.Launcher.main(Launcher.java:104)
Thanks
Chandran

Hi,
I have been trying to execute the Workshop exported Ant Script on Remote machine. In my local machine where i have access to workshop i am able to run the ant script whithout any issues. But when i try the same script on Remote machine (unix) I ma getting the below exception.
In my application, there are two projects. One web application and one EJB project, and i am trying to makr Ear file out of this.
If any of you have faced this issue or if you have any inputs pl help me out.
/opt/buildserver/home/e0271019/WFM_1031_migrated_Source/Migrated_Code_With_AntScript/wfm/build.xml:340: The following error occurred while executing this line:
/opt/buildserver/home/e0271019/WFM_1031_migrated_Source/Migrated_Code_With_AntScript/wfm/build.xml:690: The apt.factory.path was not set, but the beehive annotation processors must be on the apt factory path.
at org.apache.tools.ant.ProjectHelper.addLocationToBuildException(ProjectHelper.java:508)
at org.apache.tools.ant.taskdefs.MacroInstance.execute(MacroInstance.java:397)
at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:288)
at sun.reflect.GeneratedMethodAccessor1.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at org.apache.tools.ant.dispatch.DispatchUtils.execute(DispatchUtils.java:106)
at org.apache.tools.ant.Task.perform(Task.java:348)
at org.apache.tools.ant.Target.execute(Target.java:357)
at org.apache.tools.ant.Target.performTasks(Target.java:385)
at org.apache.tools.ant.Project.executeSortedTargets(Project.java:1337)
at org.apache.tools.ant.Project.executeTarget(Project.java:1306)
at org.apache.tools.ant.helper.DefaultExecutor.executeTargets(DefaultExecutor.java:41)
at org.apache.tools.ant.Project.executeTargets(Project.java:1189)
at org.apache.tools.ant.Main.runBuild(Main.java:758)
at org.apache.tools.ant.Main.startAnt(Main.java:217)
at org.apache.tools.ant.launch.Launcher.run(Launcher.java:257)
at org.apache.tools.ant.launch.Launcher.main(Launcher.java:104)
Thanks
Chandran

T420: Network Issues

I installed a new hard drive today in my lenovo T420. I installed Windows 7 ultimate, but it won't recognize the internal network card. I can't find the driver anywhere, and when I try to download any kind of driver that I think would help, When i hit f5, it responds with "no network adapter found" and it also doesn't show up under computer management. I'm using a USB adapter right now, but I would like the internal card to work. Also, when I tried to install the bluetooth adapter driver, it told me that the installation couldn't complete because there was no supportable hardware. I really need help on this!
I am very tech savvy, I built my own PC and run a technology repair company, but I typically don't work with software, mainly hardware. I still know my way around, so don't be afraid to get technical when helping and don't use the cliche "have you tried turning it off and back on" answer please
Thanks again!
Moderator note: corrected subject line. Was: Z585 Network Issues

Hi,
Welcome to Lenovo Community Forums!
I’m sorry to hear that network adapter is not getting detected in your Lenovo ThinkPad T420.
Check in BIOS -> Security -> I/O port access if network adapter is enabled.
Hope this helps!
Best regards,
Mithun.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

T420 Keyboard issues

I have a T420s and have keyboard issues.
G and H keys are not working at all. also when you press 2 keys together you get a beep and a delayed output of the letters you pressed.
also if you hold a key eg 'y' then press eg 't' nothing happens except a 'beep'
please help as I am a reseller and have to deliver this tomorrow morning.
lenovo tech support wont talk to me without paying till monday morning
ash

http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS014954
use the above software to do a test on the keyboard to determine whether it is hardware or software issue.
Unfortunately the support line is open only between 8 to 5 weekday, there is no afterhour or weekend support.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

T420 Build Issues

Similar Messages

Maybe you are looking for