T420 line cord international compatibility with 220v

I recently purchased a T420 and the line cord to the AC power adapter has two white tags; one saying 3A 125V for US and the other saying 3A 127V for Saudi Arabia. On the end of the cord which you plug into the AC adapter it is written in raised letters VAC7S 3A 125V-. The AC adapter it self is rated for 110-240V. My concern is the line cord as I figure there is a reason for noting the 125V and 127V usage.
I called Lenovo tech support who sent me to post-sales support who sent me back to tech support who sent me back to post-sales support who sent me to pre-sales support. No one could assure me that the line cord was compatible with 220V. One person advised me to carry an adapter, another told me to purchase a 220 to 120 power converter, another told me he thought the line cord would work but could not guarantee that it would function correctly (my thinking is it might melt down and cause a short or fire) and another person suggested I visit the Lenovo website and purchase a line cord and AC adapter for international use.
Has anyone purchased a Thinkpad T420 in the US with a North American Country pack power supply (no other choice given at the time of purchase) with the 125V tag attached and then used that equipment in a country with 220 voltage? Any problems?

KMF wrote:
My concern is the line cord as I figure there is a reason for noting the 125V and 127V usage.
The reason for the notice is to specifically advise you that the AC cord is safety compliance rated for those voltages. If you need to use the power adapter for the higher AC voltages that the adapter is safety compliance rated for, and you are concerned about regulatory compliance issues, or other possible OH&S risks, you need to use an AC cord which is safety compliance rated for the AC main voltages concerned.
The AC power cords used for ThinkPad power adapters are standard types and cords safety compliance rated to suit local voltages are readily available, usually at quite modest cost, from electronics (and similar) stores in most countries.
If regulatory compliance issues or other possible safety risks are not significant issues for you, then in practice the 125V cords do appear to work OK with up to 240V AC mains power....... but you need to understand that you are running them outside of their safety compliance rating and no one should ever officially recommend that you do that.
My personal solution is toI carry 240V AC rated power cords with my Thinkpads and use adapters at the power outlet end of the cord to access the local mains voltage from the outlet..... that way I can be confident that there will be no latent safety issues with possible insulation failure in any location that I may need to use my ThinkPads.
Cheers,
Bill
I don't work for Lenovo

Similar Messages

Internal table with header line

Hi All,
I want to declare a internal table with headerline as page attribute.
i am having to fields in the internal table ( firstname and lastname ). how to do that?
helpful answers will be rewarded.
Regards,
Azaz Ali.

Azaz,
Why do you need a header line?
Header lines are a no-no in an object context and if you need to loop at the table you can always declare a line type or an field symbol to process the table.
If you need an table as a page parameter the best way to do it is to create a table type. This is based of a line type (another name for structure ) and this may well be based off a database (transparent) table.
If you need to do special things to the table I would look at tableview iterators.
Let me dig out a blog reference for that...
... ahh here it is
<a href="/people/thomas.jung3/blog/2004/06/17/bsp-150-a-developer146s-journal-part-i-introduction View Iterator blog</a>
HTH,
N

Internal table with out header line

Hi friends,
Can u send me code for internal table with out header line : how to declare ,how to populate data and how to access the data
Regards,
vijay

Hi Vijay
There are several ways to declare an internal table without header line:
A) You can define a type table
TYPES: BEGIN OF TY_ITAB OCCURS 0,
        INCLUDE STRUCTURE ZTABLE.
TYPES: END   OF TY_ITAB.
and then your intrnal table:
DATA: ITAB TYPE TY_ITAB.
B) DATA: ITAB TYPE/LIKE STANDARD TABLE OF ZTABLE.
C) DATA: ITAB TYPE/LIKE ZTABLE OCCURS 0.
All these ways create a STANDARD TABLE
You can create other types of internal table, for example SORTED TABLE or HASHED TABLE.
These kinds of table can allow to improve the performance because they use different rules to read the data.
When it wants to manage a table without header line, it need a work area, it has to have the same structure of table.
DATA: WA LIKE ZTABLE.
DATA: T_ZTABLE LIKE STANDARD TABLE OF ZTABLE.
A) To insert the record:
If you use INTO TABLE option you don't need workarea
SELECT * FROM ZTABLE INTO TABLE T_ZTABLE
                                  WHERE FIELD1 = 'Z001'
                                    AND FIELD2 = '2006'.
but if you want to append a single record:
SELECT * FROM ZTABLE INTO wa WHERE FIELD1 = 'Z001'
                               AND FIELD2 = '2006'.
APPEND WA TO T_ZTABLE.
ENDSELECT.
Now you need workarea.
B) To read data: you need always a workarea:
LOOP AT T_ZTABLE INTO WA WHERE ....
WRITE: / WA-FIELD1, WA-FIELD2, WA-FIELD3.
ENDLOOP.
or
READ T_ZTABLE INTO WA WITH KEY FIELD3 = '0000000001'.
IF SY-SUBRC = 0.
WRITE: / WA-FIELD1, WA-FIELD2, WA-FIELD3.
ENDIF.
Anyway if you want to know only if a record exists, you can use the TRANSPORTING NO FIELDS option, in this case it doesn't need a workarea.
READ T_ZTABLE WITH KEY FIELD3 = '0000000001'
                                  TRANSPORTING NO FIELDS.
IF SY-SUBRC = 0.
WRITE 'OK'.
ENDIF.
C) To update the data: it always needs a workarea
LOOP AT T_ZTABLE INTO WA WHERE FIELD3 = '0000000001'.
WA-FIELD3 = '0000000002'.
MODIF T_ZTABLE FROM WA.
ENDLOOP.
or
READ T_ZTABLE INTO WA WITH KEY FIELD3 = '0000000001'.
IF SY-SUBRC = 0.
WA-FIELD3 = '0000000002'.
MODIF T_ZTABLE FROM WA INDEX SY-TABIX
ENDIF.
AT the end you can use the internal table to update database:
MODIFY/UPDATE/INSERT ZTABLE FROM T_ZTABLE.
See Help online for key words DATA, you can find out more details.
Max
Message was edited by: max bianchi

How to sort an internal table with a header line?

hi all,
i have declared table i_bseg type standard table of bseg with header line.
now i have populated data in i_bseg.
now i am sorting it by bukrs
ie i am writing sort i_bseg by bukrs.
before sorting all i_bseg-belnrs were populated...
but after sorting the contents of the i_bseg is changing.
some of the belnrs are getting deleted..
is there any special way to sort an internal table with header line...?

hi,
SORT <itab> [ASCENDING|DESCENDING] [AS TEXT] [STABLE].
The statement sorts the internal table <itab> in ascending order by its key. The statement always applies to the table itself, not to the header line.
If you have an internal table with a structured line type that you want sort by a different key, you can specify the key in the SORT statement:
SORT <itab> [ASCENDING|DESCENDING] [AS TEXT] [STABLE]
BY <f1> [ASCENDING|DESCENDING] [AS TEXT]
<fn> [ASCENDING|DESCENDING] [AS TEXT].
this is your sort statement: sort i_bseg by bukrs.
you try with this statement: sort i_bseg by bukrs STABLE.
regards,
Ashokreddy

Getting error of Defining an internal table with header line, SELECT-OPTIO

Hi all,
i have a coding for my smart form,In this coding i have define an structure which being used,but when i execute it it give me
error of Defining an internal table with header line, SELECT-OPTIONS, and RANGES is not allowed within a structure.Even tough you can see that in my coding im not using SELECT-OPTION or RANGES,but can't understand why it gives me this error.
Following are the code:
DATA: BEGIN OF traptab OCCURS 50.
        INCLUDE STRUCTURE mseg.
DATA: vgart LIKE mkpf-vgart,
        blart LIKE mkpf-blart,
        blaum LIKE mkpf-blaum,
        bldat LIKE mkpf-bldat,
        budat LIKE mkpf-budat,
        cpudt LIKE mkpf-cpudt,
        cputm LIKE mkpf-cputm,
        aedat LIKE mkpf-aedat,
        usnam LIKE mkpf-usnam,
        tcode LIKE mkpf-tcode,
        xblnr LIKE mkpf-xblnr,
        bktxt LIKE mkpf-bktxt,
        frath LIKE mkpf-frath,
        frbnr LIKE mkpf-frbnr,
        wever LIKE mkpf-wever,
      END OF traptab.
Thanks & Regards,
sappk25

thanks

BADI cant use an internal table with header line

hi,
In BADI, we cant use an internal table with header line, and I am calling a function module which requires internal table as import parameter, now, the table I am passing is without a header line, So how to solve this problem ?

You can use a type and then create an internal table of that type.
types :
begin of t_<example>
*field list
end of t_<example>
data :
gt_<table> type standard table of t_<example>
pass this to the FM

Dynamicly creating an internal table with header line

Hi experts,
I am trying to do a read on an internal table using field symbols of type any table. To be able to read more than one row at once, I'd like to read it into another internal table (instead of just one line and instead of looping through them one by one).
So far the following line rendered an error that the target internal table doesn't have a header line
read table <fs_v_tab> WITH KEY (<fs_comp>) = <fs_param>-low INTO <fs_v_tab>.
(also attempted using "<fs_v_tab>->*" & "<fs_v_tab>[]" to be silly)
Based on the following article, I was wondering if it were possible to dynamicly create an internal table with header line.
[http://help-abap.blogspot.com/2008/09/dynamic-internal-table-creation.html|http://help-abap.blogspot.com/2008/09/dynamic-internal-table-creation.html]
Any help or tips on how to dynamicly filter an internal table field-symbol is greatly appreciated!

Just read the online help:
This statement reads a row from internal table itab.
Or more exact:
This statement reads one row from internal table itab.
Therefore you can not read multiple lines into another table. The header line is needed to put the result in. And this is not what you intended, the result will be in the header line, not in the table itself.
If the row to be read is not uniquely specified, the first suitable row is read. In the case of index tables, this row has the lowest table index of all matching rows.
At least you have to do what you dont wanna do: looping.

Line Cord Error when connect to Sky+ Box with BT65...

Bought a new Panasonic TV and had to re sort cables took photos and replaced exactly as before. Did connect the new TV to splitter that works fine.
BT 6500 shows Line Cord error as soon as Sky box connected on own, with micro filter, with splitter. No errors prior to today so wonder if doing something daft.
We have 3x 6500s in house is it REN related? But as worked previously a bit odd.
Extension socket behind TV to micro filter - to spliter as before. Plug in cable to SKY plus box and get a line chord error showing on handset. Disconect and fault goes but noticed this fault reported on many forums BT, Virgin ....ANY advice welcome.

make sure you have connected the cable to Sky box into correct port.... the sky box has 2... an ethernet port for a cat5 cable ( rj45 bigger port ) and an rj11 port for the phone cord.... the problem is this will fit in both!! but if connected to the ethernet port it will put a loop on line and cause fault on phone line...

Dynamic Creation of Internal table WITH HEADER LINE

Dear,
Please show me the way of creating Internal table WITH HEADER LINE dynamically..
Thanks,
Nirav

Hi Parekh,
Have a look at the sample program for Dynamic internal table
This program has been developed to update any table data in the dictionary. We give table name and File name as Input fields.
<pre>
REPORT znpmmm0201.
*Types
TYPES:
 BEGIN OF ty_file,
 data(4096) TYPE c,
 END OF ty_file.
*Type-pools
TYPE-POOLS:
 truxs.
*Work areas
DATA:
 wa_file TYPE ty_file.
*Internal tables
DATA:
 it_file TYPE STANDARD TABLE OF ty_file,
 it_data TYPE truxs_t_text_data.
DATA:
 gv_dref TYPE REF TO data,
 file_name TYPE string.
*FIELD-SYMBOLS
FIELD-SYMBOLS:
 <gf_itab> TYPE STANDARD TABLE,
 <wa> TYPE ANY.
*& Selection-screen
PARAMETERS:
 p_table TYPE rsrd1-tbma_val,
 p_file TYPE ibipparms-path.
AT SELECTION-SCREEN ON VALUE-REQUEST FOR p_file.
PERFORM f4_for_p_file CHANGING file_name .
*& START-OF-SELECTION
START-OF-SELECTION.
CREATE DATA gv_dref TYPE TABLE OF (p_table).
ASSIGN gv_dref->* TO <gf_itab>.
PERFORM upload_data USING file_name.
MODIFY (p_table) FROM TABLE <gf_itab>.
*& Form UPLOAD_DATA
FORM upload_data USING file.
CALL FUNCTION 'GUI_UPLOAD'
 EXPORTING
 filename = file
 filetype = 'ASC'
 TABLES
 data_tab = it_file.
APPEND LINES OF it_file TO it_data.
CLASS cl_abap_char_utilities DEFINITION LOAD.
DATA: l_field_seperator.
l_field_seperator = cl_abap_char_utilities=>horizontal_tab.
REPLACE ALL OCCURRENCES OF '|' IN TABLE it_data WITH l_field_seperator.
CALL FUNCTION 'TEXT_CONVERT_TEX_TO_SAP'
 EXPORTING
 i_field_seperator = l_field_seperator
 i_tab_raw_data = it_data
 TABLES
 i_tab_converted_data = <gf_itab>.
ENDFORM. " UPLOAD_DATA
*& Form F4_FOR_p_file
FORM f4_for_p_file CHANGING file.
DATA:
 l_field_name LIKE dynpread-fieldname VALUE 'P_FILE'.
CALL FUNCTION 'F4_FILENAME'
 EXPORTING
 program_name = syst-cprog
 dynpro_number = syst-dynnr
 field_name = l_field_name
 IMPORTING
 file_name = p_file.
file = p_file.
ENDFORM. " F4_FOR_p_file </pre>
Thanks,
Venkat.O

Sorting internal table with line types

Hi,
I have internal table juts for an example with four entries as below:
A[]
Line.....Line Types
444001.....P
New York...C
Evershine..B
Mary.......N
I want to sort the internal table with line types in order of lin types NBCP.
How can i do this ?
Please help.
Note: Above example is just with four entries, there might be internal table with ten entries and ten defined sorting order for line types.

Hi Tushar,
Please note that we can't changes the mandatory sequence of the address format as defined in the country specif address format. We can change the sequence of others fields by line_priority.
Try to change the address type :
ADDRESS_TYPE - Address type (from 3.0C)
There are three types of address:
Address type '1': addresses of firms or organizations; the address structure which is used in most SAP applications as 'Address'.
Address type '2': address of a person
Address type '3': work address, usually the address of a contact person in a company
Please use T/code "OY01"> Select Country> Example :AU"--> Display --> Select address key and press F1. You will find SAP 's Address format configuration .
sap help:
Formatting Routine Key for Printing Addresses
For printing addresses, there are country-specific routines which in each case copy the correct postal formatting of the address.
The three-character "Address Layout Key" for the recipient country controls which of the routines available for formatting addresses in the relevant country is used.
These routines are programmed into the ADDRESS_INTO_PRINTFORM function module.
They are based on different national and international guidelines and norms, including:
ISO 11180,
contracts of the World Postal Union (Seoul 1994),
international address samples from the World Postal Union
as well as the available rules of the individual countries.
Below you will find an overview of the country-specific formats currently implemented.
Customers can program their own formatting routines using a customer exit. The SZAD0001 SAP enhancement has been defined in the package SZAD for this (-> transaction CMOD).
General formatting rules
The following parameters are used depending on the transaction:
whether the company address (street/house number) or the P.O. Box address is printed if both exist,
how many lines are available for printing,
which is the sender country.
If there are not enough lines, then lines are left out according to a standard sequence.
The address format depends on whether the sender country is the same as, or different from, the recipient country. The country is always specified from abroad, either as a text name, or as an identification code of up to three characters (license plate code or country key).
Where the country name is written out in full, it is written in the language of the sender country. If a language is not specified for the sender country, or the sender country itself is not specified, the logon language is used instead.
Exception: the language for the country code can be explicitly overwritten by a parameter in the print program (e.g. when the country code for customs transit papers is always to be specified in a particular language, such as English). if the "Print country name in recipient language" flag is set in the print program, the recipient language is used.
Other language-dependent components such as the title and the word 'PO Box' are printed in the recipient language or the recipient country language. If this cannot be determined, the logon language is again used.
For all formats except Great Britain (006), Japan (013), and South Korea (017), the core of the address is formatted as follows (without empty lines, except for the compulsory empty line:)
title line (if applicable)
name block (differs depending on the address type, see below)
street address or PO Box
(compulsory empty line, if applicable)
city line with postal code
country code (if applicable)
The city line and the country name are always printed in upper case for foreign addresses (only for the complete address, not for short forms).
The name block generally consists of the following:
"Normal" addresses (address type SPACE and address type 1):
NAME1
NAME2
NAME3
NAME4
Personal addresses (address type 2):
Title of person and name of person
Business address with department and contact person (address type 3):
NAME1
NAME2
NAME3
NAME4
department
title of person and name of person
In addresses entered using Business Address Services (central address management) (see Release notes Central Address Management for Release 4.0 and Central Address Management for Release 4.5 ), the street address can comprise several lines (see Print street address), otherwise street and house number are maintained in the Street field.
Some countries do not have a compulsory empty line (see notes below). The city and district are printed in the city line, connected by a hyphen (exceptions: 004 USA, 006 Great Britain/Ireland, 013 Japan, 015 Germany, 017 South Korea, 019 Denmark), provided that the total length does not exceed 35 characters. If a different city is specified for the PO Box (PFORT), this is used in the PO Box address.
In all formats which use a country code (currently 001 European standard format 002 Italy, 011 Switzerland and 014 Austria ), the license plate code for that country is used. If this is not maintained, the country key in table T005 is used.
If the "Print country name in foreign addresses" flag is set for the sender country in table 005, the country code is not used; the country name is printed in the last line of the address.
Formats 004 (USA), 005 (Canada) and 008 (Singapore) contain a line ('F') for the function of the contact person in the company (if address type = '3'). This line comes immediately after the line 'N' (Name (and title) of the natural person).
In formats 002 (Italy), 004 (USA), 005 (Canada), 006 (Great Britain), 007 (Brazil) and Australia (009), the REGIO field (Region, State, Province, County) is formatted. For the USA, Canada, Brazil and Australia, the key from table T005S is used; for Great Britain the text name from table T005U.
In all countries for which no "Address structure key" is maintained, a standard format is used which corresponds to format "010".
Hope this may help you.
Lanka

Audio Compatibility with iHome

Hey everyone,
You all have been so helpful in the past, so I'm coming to all you Apple support forum gurus for two very puzzling audio questions:
1) I have an iHome Bluetooth/Alarm Clock (see here: http://www.ihomeaudio.com/products.asp?productid=10460&deptid=1006), which was working fine with my MacBook Pro in terms of Bluetooth until one day I shut the computer while it was still connected to the speakers. Now, the two won't seem to pair (and yes, I'm using the 1234 code)--any ideas on how to get them to pair now? I've tried rebooting the computer and everything.
2) Because of this issue, I bought a very long auxiliary cord so that I can use the line in to the speakers from my headphones port on the MacBook Pro. Problem: it seems like the audio is only playing mono, not stereo, because I'm definitely not getting the full song out of the speakers. I tried tampering with the audio settings on my computer with no luck. Any ideas on this one, either?
Any help would be GREATLY appreciated! Thanks so much everyone!!

Hi Brian:
iChatAV is compatable with PC AIM users utilzing AIM 5.9 for video chat.
The key is into your set-up. Being at a hotel, MAY hinder you connection activities.
The key is to focus on your set-up first. Are you able to connect to a user that has no known issues? You can find auto-responders and other people to test with here: http://www.ralphjohnsuk.dsl.pipex.com/ContactTesters.html
There is even a PC that is set-up to auto respond with a picture of a Windows XP box when your connected. IF you are able to connect with other users and the auto responders, it's a good chance the issue is with the user on the other end.
Here's a good sight to review for your windows friend to ensure they are set-up correctly: http://www.mvldesign.com/videoconferencetutorial.html
If everything is set-up correctly, you should be able to conduct a one way video chat with an PC AIM user with no issues. (I've done it many times)
Since you are in a hotel, you may receive varied results depending on how they have their network set-up. Try connecting to the testers and go from there.
I hope this helps! Have a safe visit in Canada.

Itunes 9.1 not compatable with XP?

Tried to download 9.1 and keep getting error message that says: The software you are installing has not passed Windows Logo testing to verify its compatibility with Windows XP. Continuing installation of this software may impair or destabilize operation of your system either immediately or in the future.
I have reboot computer several times, etc. Have never had a problem with any updates to itunes or iphone till now.
Thoughts?

Itunes 9.1 is definitely NOT compatible with Windows XP at this time. The culprit appears to be the Bonjour services package. I recently attempted to install via 3 methods: through Apple Update, via direct download over wireless and via direct download over wired connection. The result was the same in all three instances: when attempting to start itunes 9.1, it would immediately crash with a message "Itunes has encountered a problem and needs to close...". Upon checking the application event viewer (control panel > performance & maintenance > administrative tools > event viewer) I was able to determine that the itunes crashes were due to Bonjour in all but one instance. Bottom line: steer clear of itunes 9.1 until Apple gets their comparability issues corrected.

Budgeting thru Internal Order with Account assignment category 'A'

Dear All
I want Budgeting thru Internal Order with Account assignment category 'A'
i.e
Created Assets with Tcode As01
Created Internal Order and assigned budget amount to IO with Tcode KO01 and KO22
Created Purhcase Requisition with Account assignment catg as 'A' i.e asstes. Also given Internal Order No and Asset code in PR.
Releases PR with ME54N
Created Purchase Order with Account assignemnt catg as 'A' i.e asstes. In Purchase Order it displays Internal Order No. and Asset code which i have given in PR in Account assignemnt tab on Item level
Released Purchase Order.
Now i am checking budget detail in Tcode : S_ALR_87013019 -> List: Budget/Actual/Commitments , Here it gives message , "No line item were selected " in Commitment line items.
Actually my requirement is , i want budgeting thru internal order and want to use Account assignment category as 'A' (Assets) in PR and PO.
Why it's not showing detail in report S_ALR_87013019 .
What is solution for my requirement. Is it possible with some configuration or by other options.
Thanx & Regards
Swati Shah

Hi Swati,
You can do this in Asset Accounting. By standard MIGO Posting Date is taken as capitalization date for asset. You can configure to make it 'Document Date'.
So, whenever user is posting thru MIGO, he will have better control on deciding capitalization date by inputting appropriate date in Document Date Field in MIGO.
Check this thread..
Re: Depreciation start date for asset thru MIGO
Regards,
Sayujya

How to convert internal table with dynamic fields to XML

Dear all,
I met a problem like the following:
The aim is to transform the following parameter to XML
IT_FIELD stores the dynamic filed name of the internal table,with these fields, the dynamic internal can be created by cl_abap_tabledescr=>create(it_field)
IT_VALUE stores the value of the internal table dynamically created with dynamic fields.
For example
IT_FIELD =>
line1: FIELD1
line2: FIELD2
line3: FIELD3,
three lines in this internal table.
dynamically created internal table structure FIELD1 FIELD2 FIELD3
And IT_VALUE=>
1 2 3 (First line)
11 22 33
two lines of data.
Do you have any idea about how to transform the IT_VALUE to XML here? And also the transformed XML to the IT_VALUE.( we may need remember IT_FIELD here for later XML to IT_VALUE.)
Hope I describe the problem clearly.
Any inputs will be appreciated.
Edited by: Max Tang on Jan 12, 2009 3:46 PM
Edited by: Max Tang on Jan 12, 2009 4:14 PM

Hi,
you need to implement a bit of coding for that.
With the 'do varying' statement abap provides a loop over those fields. Within this loop you can build up a new internal table with one entry for each period and amount.
kind regards
Siggi
PS: I am not very familiar with CO, but I guess there will be a standard extractor for that.

Excel data transfer into SAP internal table with GUI_UPLOAD

hi all,
i m using SRM4 system and i wanted to develop one report which will upload data from excel and convert it into IT.
i know that many threads are posted on this topic.
but my requirement is slight different. in the system only one function module is available that is "GUI_UPLOAD" and we want that user shd not save file as tab delimited before calling this fm. instead, program shd take care of all these things...
please suggest something asap..
helpful ans will be rewarded..
thanks,
jigs.

Dear Jigs,
Please go though the following lines of code:
D A T A D E C L A R A T I O N *
TABLES: ANEP,
BKPF.
TYPES: BEGIN OF TY_TABDATA,
MANDT LIKE SY-MANDT, " Client
ZSLNUM LIKE ZSHIFTDEPN-ZSLNUM, " Serial Number
ZASSET LIKE ZSHIFTDEPN-ZASSET, " Original asset that was transferred
ZYEAR LIKE ZSHIFTDEPN-ZYEAR, " Fiscal Year
ZPERIOD LIKE ZSHIFTDEPN-ZPERIOD, " Fiscal Period
ZSHIFT1 LIKE ZSHIFTDEPN-ZSHIFT1, " Shift No. 1
ZSHIFT2 LIKE ZSHIFTDEPN-ZSHIFT1, " Shift No. 2
ZSHIFT3 LIKE ZSHIFTDEPN-ZSHIFT1, " Shift No. 3
END OF TY_TABDATA.
Declaration of the Internal Table with Header Line comprising of the uploaded data.
DATA: BEGIN OF IT_FILE_UPLOAD OCCURS 0.
INCLUDE STRUCTURE ALSMEX_TABLINE. " Rows for Table with Excel Data
DATA: END OF IT_FILE_UPLOAD.
S E L E C T I O N - S C R E E N *
SELECTION-SCREEN: BEGIN OF BLOCK B1 WITH FRAME,
BEGIN OF BLOCK B2 WITH FRAME.
PARAMETERS: P_FNAME LIKE RLGRAP-FILENAME OBLIGATORY.
SELECTION-SCREEN: END OF BLOCK B2,
END OF BLOCK B1.
E V E N T : AT S E L E C T I O N - S C R E E N *
AT SELECTION-SCREEN ON VALUE-REQUEST FOR P_FNAME.
CALL FUNCTION 'KD_GET_FILENAME_ON_F4'
EXPORTING
PROGRAM_NAME = SYST-REPID
DYNPRO_NUMBER = SYST-DYNNR
FIELD_NAME = ' '
STATIC = 'X'
MASK = '.'
CHANGING
FILE_NAME = P_FNAME
EXCEPTIONS
MASK_TOO_LONG = 1
OTHERS = 2
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
E V E N T : S T A R T - O F - S E L E C T I O N *
START-OF-SELECTION.
Upload Excel file into Internal Table.
PERFORM UPLOAD_EXCEL_FILE.
Organize the uploaded data into another Internal Table.
PERFORM ORGANIZE_UPLOADED_DATA.
E V E N T : E N D - O F - S E L E C T I O N *
END-OF-SELECTION.
*& Form UPLOAD_EXCEL_FILE
text
--> p1 text
<-- p2 text
FORM UPLOAD_EXCEL_FILE .
CALL FUNCTION 'ALSM_EXCEL_TO_INTERNAL_TABLE'
EXPORTING
FILENAME = P_FNAME
I_BEGIN_COL = 1
I_BEGIN_ROW = 3
I_END_COL = 7
I_END_ROW = 32000
TABLES
INTERN = IT_FILE_UPLOAD
EXCEPTIONS
INCONSISTENT_PARAMETERS = 1
UPLOAD_OLE = 2
OTHERS = 3
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
ENDFORM. " UPLOAD_EXCEL_FILE
*& Form ORGANIZE_UPLOADED_DATA
text
--> p1 text
<-- p2 text
FORM ORGANIZE_UPLOADED_DATA .
SORT IT_FILE_UPLOAD BY ROW
COL.
LOOP AT IT_FILE_UPLOAD.
CASE IT_FILE_UPLOAD-COL.
WHEN 1.
WA_TABDATA-ZSLNUM = IT_FILE_UPLOAD-VALUE.
WHEN 2.
WA_TABDATA-ZASSET = IT_FILE_UPLOAD-VALUE.
WHEN 3.
WA_TABDATA-ZYEAR = IT_FILE_UPLOAD-VALUE.
WHEN 4.
WA_TABDATA-ZPERIOD = IT_FILE_UPLOAD-VALUE.
WHEN 5.
WA_TABDATA-ZSHIFT1 = IT_FILE_UPLOAD-VALUE.
WHEN 6.
WA_TABDATA-ZSHIFT2 = IT_FILE_UPLOAD-VALUE.
WHEN 7.
WA_TABDATA-ZSHIFT3 = IT_FILE_UPLOAD-VALUE.
ENDCASE.
AT END OF ROW.
WA_TABDATA-MANDT = SY-MANDT.
APPEND WA_TABDATA TO IT_TABDATA.
CLEAR: WA_TABDATA.
ENDAT.
ENDLOOP.
ENDFORM. " ORGANIZE_UPLOADED_DATA
In the subroutine --> ORGANIZE_UPLOADED_DATA, data are organized as per the structure declared above.
Regards,
Abir
Don't forget to award points *

T420 line cord international compatibility with 220v

Similar Messages

Maybe you are looking for