T420s hard drive noise / speed /battery life trade off and Screen Roll Cage Info

I know this is a brand new laptop but has anyone over at lenovo spent enough time with both the 7200 rpm and the 5400 rpm version of the 320GB hard drive in this laptop? I am trying to decide between ordering one and would like to get the 7200 rpm but I really dislike hard drive spinning noises in quiet environments. I am currently using the t400 with the 5400 RPM 320Gb drive (which I realize may be different from the drives in the new t420s) and do not find the noise objectionable but would like to get the 7200 in the t420s if there is no noise penalty and very little battery life penalty. Also, does the T420s have a "screen" roll cage like my current T400. I had heard that the T410 did away with the screen roll cages....
Thank You for any assistance.
Solved!
Go to Solution.

The T420s's rollcage is made of a hybrid carbon fibre reinforced plastic. It's not metal since that interferes with the wireless signal.
It's apparently a bit better than the one the T510 has right now (which is the same carbon-reinforced plastic)- and the T410, with a "weaker" roll cage, should pass a 1.6 metre drop anyways.
I can vouch for that plastic's use since you can step on another laptop who's lid (I'm pretty sure it's made from this) is made from that (an old 600E) and it will survive.
Also, the noise isn't all that different for 5400 RPM vs 7200 RPM. The fan will be louder if you are using it.
And if you really hate hard drive sound and want a bigger boost than just an RPM bump, consider an SSD. That'll blow any hard drive out of the water in terms of speed, but will do the same to your wallet if you need anything larger than 40-60 GB. And, if you choose to do this, be aware that the T420s only takes SSD's that are 7mm high- so you'll probably need to get an X25-M or Intel 320 to accommodate that.

Similar Messages

Why my Mac Pro hard drive noise and too slow?

Why my Mac Pro hard drive noise and too slow? Totally 8 gb speed system but now very slow . Please give some suggestions

Another thing you can do in Lion (and ML) is click on the "Info" button in Disk Utility to get the SMART status of the drive.It's more detailed now than it used to be and it might tell you if something is wrong.
A lot can go wrong with a hard drive which is why I tend to point people to the downloads section of the following web site:
http://scsc-online.com
They have a free hard drive troublleshooting download book there. I reccommend people download that before asking questionis because there are tons of problems that can act like hard drive problems when there's nothing wrong with the system at all. For example, how full is the drive? How many applications are running? What's the status of Spotlight indexing? How many apps are you running? How much memory do you have?
I could probably think up 20 or 30 more if needed.

Disharging with USB, Freezing on Sync, Hard Drive noise on Line Out

I have been dealing with three issues with my 60GB iPod click wheel with color display (Photo).
The first is something that slowly creeped in, which is hard drive noise that is audible through the line out when the iPod is charging in a dock. I'd like to say it's like a ground loop issue, but it's in my car, on my iHome, and on my apple dock when plugged into power on a stereo system. It sounds like the spinning of the hard drive is correlated to the noise.
Second, over the past year or so, I've noticed that when I have the iPod plugged into any mac using USB, the iPod discharges. My friend has noticed the same problem on her 40GB 3rd generation iPod. We've tried them on several computers. Firewire connection, no problem, only USB when plugged into a computer, not the power adapter.
Just recently, the iPod froze up iTunes and the rest of my Mac (G4 MDD Dual 1gHz, OS X 10.4.10, iTunes 7.4.2) during sync. I made reformatted the iPod using Disk Utility, Restored to iPod, making sure to plug into power to finish the restore, then attempted to resync. Two attempts of this and I get the same result, a freeze.
The first two issues, I've adapted with, but this last one is just frustrating. I will attempt to sync using a firewire cable, but that should not be the solution. This iPod came with a USB cable, it should charge and sync with one. If anyone has any ideas, please let me know. Thank you!

ok I went here for instruction on how to take it apart since I wasn't having much luck on my own:
http://www.flexbeta.net/forums/index.php?act=ST&f=20&t=8269
his tip worked for me so far. hopefully this won't be just a temporary fix:
Good tip: if your iPod seems dead and the hard drive is throwing errors pull out the connection at the bottom of the ipod mainboard and plug it back in, this will hard reset your ipod and worked a few times for me

Hard Drive noise on iMac

Seems if I tilt the monitor down more the hard drive noise gets louder... Is this a common issue with the new Intel based iMacs? I will have to check but computer was also in sleep mode for awhile so not sure if this still happens... It isn't too loud... but if it says like this it will be annoying...

Happened today on my new Macbook Pro, 15-inch i7 while editing in final cut. Has happened several times before this, as well. Never had this problem while editing on other computers, including an older Macbook Pro and also a 2.26 Ghz dual Quad Core tower.
The clip that caused the blowout had the following audio: 16-bit integer (Big Endian), Stereo, 19.2 Khz.
My sequence settings for audio are currently 16-bit, 48 Khz, Channel grouped.
Please get around to fixing this, folks at Apple. I work as an editor and I currently can't wear headphones for fear of blowing out my eardrums.

Lacie 500GB External Hard Drive Fan speed / heat issues?

I have a 500gb Lacie Mini hard drive with the 1394/usb2.0 hub and for some reason when it is connected to my mac mini in the office, it works totally fine, doesnt spin really fast or anything. When I take it home and hook it up to my other mac mini, after 10-15 minutes the fan starts to blow at full speed on the Lacie. The mac mini at home is from March 2005 and its a 1.66 Core Duo, and the one at the office is from March 2007, and is also a 1.66 Core Duo, both with 2gb of ram.
I have noted at the bottom of my home mac mini is very warm to the touch after feeling between the drive and the computer, but it seems odd to me that both computers dont get just as hot considering they are virtually identical aside from the build date. Has anyone else experienced this problem with their Lacie mini drive? The fan spins so high on the drive that its annoying to even use it, and I'd like to take care of it if theres a remedy.
Thanks!

I agree, the link you posted is strangely inaccurate. I have been trying to post the attempts on this link: http://www.123macmini.com/forums/viewtopic.php?p=109630#109630 but as you can tell I have been frustrated with the whole process. The posts may be confusing because they are step by step. The lacie drive is loud under the mini but not when it is by itself.
As of now the test seem to be inconclusive. It is so strange that I would be convinced if someone told me the fan in the lacie has a temperature sensor inside. But the only thing I can come up with is that the mini gets hot on the bottom, while the lacie gets hot on top. Their combined heat seems to be too much for the lacie's fan to cool. I will also mention that I have fan control software installed on the mini, but this doesn't seem to have any effect as I am not changing the settings during my tests.
The fan having a temperature sensor is just crazy... I removed the fan from the lacie (fan still plugged in) and set up the stack. The lacie bottom was removed for this test. The lacie fan never turned on, and the drive increased in temperature that I felt was too hot. This is where sensing strips would assist in further data.
So here is my next step: Since the fan didn't turn on when the lacie bottom was removed, it seems that the open back and open bottom (the back and bottom is one piece) was enough to keep the sensor from turning on the fan. But as said before, I felt the drive was still too hot. So maybe the lacie case needs more ventilation. Two ways I have thought to do this:
----- cut the fan one large hole instead of a bunch of little ones, allowing more air out.
- or -
----- cut the bottom vents out (maybe not all of them) to allow more air intake.
I think the first one would solve the problem, but I don't currently have the time to do it. I am going to cut the fan hole first, once I get the time.
I will tell you that the lacie drive is mounted closest to the top of the case. I have thought of purchasing some thermal sensing strips to determine what is hot and when; haven't yet.
AndyO, you said everything right except one part... the mini's air-intake is the vents on the bottom, and the air is obviously pushed out the back by the horizontal fan (there is a special plastic mold that the fan sits horizontally in). Which you would lead us to believe that the mini would heat up with the lacie underneath, but I haven't noticed any drastic changes in the mini fan speed or temperature. Instead the lacie drive gets hot or at least the fan goes crazy.
Hope this helps, I'll let you know when I get the scalpel (really sharp knife) out.
-p13th0r4

Is your mpb 17" c2d hard drive noise acceptable?

I got 17" mbp two days ago, i even couldn't notice the hard drive noise while daily using since I either turned my tv on or playing music. But in the mid night, I have to turn off the TV, trun off the music or at least turn down the volumn, then I noticed that the hard drive noise. While downloading files, or opening some big files, it just sounds scary and horrible, I have the stocked 5400rpm 160GB hitatchi hard drive. Do you guys get the same issue? Is that acceptable?
btw, I'd use a compaq laptop for 3 years, no that sound at all. Just dont know why Apple couldn't put a quiet hard drive into the mbp.

Unfortunately not all drives are quiet, or in extreme cases even quiet. There is even variance within the same model drives. The thing is, what you need to determine is what is considered "reasonable". Drive noise, which is normally head chatter (the drive head moving backa and forth) is inevitable and to some degree we all have to live with it.
If you are truly concerned over the noise your drive makes then I would contact AppleCare and discuss it with them. I had a drive replaced due to noise although that wasn't "head chatter" rather a squealing spindle.

Intermittent Hard Drive Noise (crackling) Only While Surfing the Web

Any thoughts on this? It's just an annoying sound, crackling every 30 seconds at most, sometimes every few minutes. I've got a 200GB 7200 Hitachi HTS722020K9SA00 Revision DC4AC77A.
Thanks for your help!

It is always wise to worry about any unusual noise from a hard drive. Do back up your data and keep it backed up, just in case.
If you want a more detailed look into your hard drive, you can download S.M.A.R.T. Utility and run it several times for free:
http://www.versiontracker.com/dyn/moreinfo/macosx/32454
This may be nothing more than a normal if annoying sound. You might want to talk to Hitachi about it to see if it is a known issue with that drive and if they have any suggestions for eliminating the noise.
Good luck!

My 7th generation ipod classic is making some hard drive noises...it makes me feel so worried that it might be a hard drive issue!

Please help me and advise if i should be changing my ipod.
is there any ipod 7th generation that does not make this hard drive noises? or is this the case with all the ipods???
I'm not feeling well about this issue, as i just noticed while surfing through my songs!

What you are hearing is the sound of the iPod's internal hard drive spinning up to read data from disk for playback. So basically, what you are hearing is completely normal for the iPod Classic. If you still feel that it is unusually loud, find another person with an iPod Classic and compare them. If your iPod is louder, it could be signs of a faulty/damage drive, but don't be sure quick to jump to conclusions.
B-rock

IMac 2009 (21 inch) making hard drive noises during sleep mode - normal??

Hi there guys,
I have an iMac 21 inch (2009) , 3ghz C2D, 4GB Ram, 1TB hard drive (the hard drive was upgraded straight thru apple, when i bought it i paid extra for a 1tb hard drive, its not a DIY hard drive upgrade)
aniways, I recently noticed that during sleep mode, occasionally (not all the time) I can hear some faint clicking / hard drive noise, which is really weird because i put the imac in sleep mode and it really shouldnt be doing that no?
My 13 inch macbook pro 2010 never does this in sleep mode, its always dead silent
Im just wondering if this hard drive accessing / clicking noise during sleep mode is normal in imacs??

Im just wondering if this hard drive accessing / clicking noise during sleep mode is normal in imacs?
No it should not be doing anything but sleeping. The SMC controls sleep, try resetting it.
Reset the SMC
• Shut down the computer.
• Detach the computer's power cord.
• Press and hold the power button for 5 seconds.
• Release the power button.
• Reattach the computers power cable.
• Turn on the computer.
Dah•veed

IPhone 4S Battery Life: Best solutions and procedures for 1st time user: 1-Do you have a battery life issue (learn first what the usage time spec is about) 2-What can you try to remedy the situation without reading 500 pages of posts

What follows is a grouping of some of the most fruitful procedures - from what I've seen in the biggest battery life issue thread - and some background information and discussion for solving or improving the battery life with the iPhone 4S and may be applicable also to devices on which iOS 5.0/5.0.1 has been applied. Credit goes to the respective users who contributed this information to the forum and they should be commended for doing so. This is not a final listing. The goal here is to provide a first stop sort of knowledge base document for newcomers instead of having them perusing the never ending threads where the wheel is reinvented on every page...
Please don't post your questions, usage screenshots, or claims that it worked or not for you or anything here except PROCEDURES/DEBUG STEPS/SOLUTIONS or improvements to the procedures already listed here. Try to use point form and to be as concise and clear as possible. Hope all this helps.
Thank you and good luck!
General info and specs
First, take a look Apple's battery tips, info and specs(obligatory reading for all Iphone 4S users - read it once and for all):
http://www.apple.com/batteries/iphone.html
http://www.apple.com/batteries/
... you didn't read it? loll Always remember this i.e. the definition of "usage":
Usage: Amount of time iPhone has been awake and in use since the last full charge. The phone is awake when you’re on a call, using email, listening to music, browsing the web, or sending and receiving text messages, or during certain background tasks such as auto-checking email.
I'm still not convinced you read the links so here's what Apple has to say in terms of fine tuning your battery life:
Optimize your settings
Depending on how they are configured, a few features may decrease your iPhone battery life. For example, the frequency with which you retrieve email and the number of email accounts you auto-check can both affect battery life. The tips below apply to an iPhone running iOS 5.0 or later and may help extend your battery life.
Minimize use of location services: Applications that actively use location services such as Maps may reduce battery life. To disable location services, go to Settings > General > Location Services or use location services only when needed.
Turn off push notifications: Some applications from the App Store use the Apple Push Notification service to alert you of new data. Applications that extensively rely on push notifications (such as instant messaging applications) may impact battery life. To disable push notifications, go to Settings > Notifications and set Notifications to Off. Note that this does not prevent new data from being received when the application is opened. Also, the Notifications setting will not be visible if you do not have any applications installed that support push notifications.
Fetch new data less frequently: Applications such as Mail can be set to fetch data wirelessly at specific intervals. The more frequently email or other data is fetched, the quicker your battery may drain. To fetch new data manually, from the Home screen choose Settings > Mail, Contacts, Calendars > Fetch New Data and tap Manually. To increase the fetch interval, go to Settings > Mail, Contacts, Calendars > Fetch New Data and tap Hourly. Note that this is a global setting and applies to all applications that do not support push services.
Turn off push mail: If you have a push mail account such as Yahoo! or Microsoft Exchange, turn off push when you don’t need it. Go to Settings > Mail, Contacts, Calendars > Fetch New Data and set Push to Off. Messages sent to your push email accounts will now be received on your phone based on the global Fetch setting rather than as they arrive.
Auto-check fewer email accounts: You can save power by checking fewer email accounts. This can be accomplished by turning off an email account or by deleting it. To turn off an account, go to Settings > Mail, Contacts, Calendars, choose an email account, and set Account to Off. To remove an account, go to Settings > Mail, Contacts, Calendars, choose an email account, and tap Delete Account.
Turn off Wi-Fi: If you rarely use Wi-Fi, you can turn it off to save power. Go to Settings > Wi-Fi and set Wi-Fi to Off. Note that if you frequently use your iPhone to browse the web, battery life may be improved by using Wi-Fi instead of cellular data networks.
Turn off Bluetooth: If you rarely use a Bluetooth headset or car kit, you can turn off Bluetooth to save power. Go to Settings > General > Bluetooth and set Bluetooth to Off.
Use Airplane Mode in low- or no-coverage areas: Because your iPhone always tries to maintain a connection with the cellular network, it may use more power in low- or no-coverage areas. Turning on Airplane Mode can increase battery life in these situations; however, you will be unable to make or receive calls. To turn on Airplane Mode, go to Settings and set Airplane Mode to On.
Adjust brightness: Dimming the screen is another way to extend battery life. Go to Settings > Brightness and drag the slider to the left to lower the default screen brightness. In addition, turning on Auto-Brightness allows the screen to adjust its brightness based on current lighting conditions. Go to Settings > Brightness and set Auto-Brightness to On.
Turn off EQ: Applying an equalizer setting to song playback on your iPhone can decrease battery life. To turn EQ off, go to Settings > iPod > EQ and tap Off. Note that if you’ve added EQ to songs directly in iTunes, you’ll need to set EQ on iPhone to Flat in order to have the same effect as Off because iPhone keeps your iTunes settings intact. Go to Settings > iPod > EQ and tap Flat.
Usage specs for the 4S - http://www.apple.com/iphone/specs.html:
Talk time: Up to 8 hours (12.5% per hour drain) on 3G, up to 14 hours (7.1% per hour drain) on 2G (GSM)
Standby time: Up to 200 hours (0.5% per hour drain)
Internet use: Up to 6 hours on 3G (16.6% per hour drain), up to 9 hours (11.1% per hour drain) on Wi-Fi
Video playback: Up to 10 hours (10% per hour drain)
Audio playback: Up to 40 hours (2.5% per hour drain)
So a scenario of normal usage could be for example: 4 heavy hours of 3G internet browsing (66.4%), with one hour of call on 3G (12.5%) and 22 hours of standby (11%) = 100%
A battery life issue is a problem where the drain is really out of spec either during usage or standby or both. For example, multi-% per minute drain during usage or a 10% drain per hour during standby is problematic. Browsing the internet on 3G during one hour and losing 16-17% is not.
Apple's test methodology for claiming the specs:
http://www.apple.com/iphone/battery.html
Procedures
davidch tips (reset+full discharge recharge):
Go through these steps to address the battery after updating to iOS 5.0.1:
1. Reset all settings (settings app-> general-> reset)
2. Go through initial setup steps (lang, wifi, siri, enable location, etc) and choose setup as new phone (don't worry your apps, data, contacts, mail will still be there). Do NOT restore from iCloud or iTunes (It can copy back corrupt settings)
3. Turn off system location services timezone and iAd
4. Fully discharge battery (tilll it shuts off with the spinning wheel)
5. Fully recharge battery (overnight if possible)
In my experience this improves the Standby battery drain issue significantly in most cases. It reduces drain from 2-4% or more per hr to 0.5% or less. It has worked for many, many users now. If it does not work after a few try's you may have a real battery or hardware issue and should contact Apple. Good Luck!
ram130's variant of davidch i.e. additional steps:
Now using davidch original steps and attaching the tweaks I made to get me more usage. As shown on page 29.
Go through these steps to address the battery after updating to iOS 5.0.1:
1. Reset all settings (settings app-> general-> reset)
2. Go through initial setup steps (lang, wifi, siri, enable location, etc) and choose setup as new phone (don't worry your apps, data, contacts, mail will still be there). Do NOT restore from iCloud or iTunes (It can copy back corrupt settings)
3. Turn off system location services timezone and iAd
4. Fully discharge battery (till it shuts off with the spinning wheel)
5. Fully recharge battery (overnight if possible)
6. Disable Siri 'Raise To Speak' and REBOOT *( if possible use another camera to verify the                 infrared is off after the reboot).
7. Set emails, icloud and calendars to fetch. ** test. Mines on hourly.
8. If your in a no signal and your phone is saying "Searching..." even after 10mins, reboot while in that area and after 1-2min it should say "No Service". This mainly applies to Verizon customers and improve battery life in these areas.
9. *optional* Goto Settings > General > Network and you will see "Hotspot.." loading something, wait a few seconds and it should say "setup personal hotspot" then exit out.
* I notice a great improvement after disabling this and rebooting. This increased my "screen on" usage or at least helped it. Make the change.
** I have not tested push yet to narrow down the drain but I had this change on my phone. I believe exchange push is responsible for some stand by drain. As for icloud, haven't notice much of a difference. Just try it for a day. My email still came in fast most times. Again still testing, will report back on these..
buxbuster tips(wifi sync, iCloud):
These are my own tested workarounds that worked for my iPhone 4S and seemed to have worked for others as well :
Workaround number 1. Deselect wifi-sync in iTunes and press sync.
If that doesn't work try :
Workaround number 2 : Remove iCloud, reset network settings. ( I guess this won't work for you since you don't have it enabled ).
If both workarounds fail, you can always try to completely wipe your phone. That also solved some of the cases out there.
rolandomerida tips - i.e. buxbuster and additional steps:
Finally, I solved the syncing error loop. My contacts are syncing flawessly again between my devices and iCloud, and yes, the battery stopped draining, which is the main topic here.
I followed instructions from buxbuster (check his workaround a few pages up!) and an additional BIG step to restore contacts and syncing, as seen in a MacRumors forum.
This is what I did:
1. Make a backup of your Address Book, using the vCard option (or both, it doesn't hurt). Save it for later.
2. In your iPhone, delete iCloud account. When it asks, accept both: delete AND delete from my iPhone.
3. Reset network settings. The iPhone will restart, then will ask you to unlock the SIM card.
4.Turn Wi-Fi on.
5. Add the iCloud account again.
That's for Buxbuster's workaround. For some, it might work just like that. My iPhone repopulated from iCloud after step 5, but I still had that "server error" on iCloud. I had to do some extra steps, since my Mac was not syncing to iCloud and couldn't edit anything on my Mac or iCloud. Syncing back had to be fixed, too. If not, the syncing loop would continue from my iPhone, and the battery would drain awfully again.
1. In System Preferences -> iCloud, I turned Contacts off. I chose "keep on My Mac" those contacts, but I got an empty Address Book after a while. And a few minutes later, iCloud contacts were empty and my iPhone also. It is scary at first! Now, before importing that vCard backup...
2. Turn Wi-Fi off. This is important, since your contact-empty iCloud will attempt to wipe your Address Book from your Mac in seconds after importing.
3. Import your vCard backup to Address Book. Just drag it to your blank Address Book window; it asks if you want to import "x" number of cards. Of course, say yes.
4. Turn Wi-Fi on, and then iCloud contacts on again (System Preferences -> iCloud). It will offer to merge your newly populated Address Book with iCloud (which is empty at this point). It should upload every single contact to iCloud, and then to your iDevices. If not, a fifth step would be to import the vCard file to iCloud, but it shouldn't be necessary.
So, with iCloud syncing working correctly, there is no battery draining! Again, that was my particular issue.
I can't tell if this is the single answer to the widely spread battery draining problem, but it sure can be fixed with these workarounds, and yes, Apple should address the problem with a future update, for we affected customers don't need workarounds in the first place
This is the MacRumors discussion:
http://forums.macrumors.com/showthread.php?t=1256807
And dont' forget to check buxbuster's fix, video, and THANK him!
Miless tips (full 800mb release of 5.0.1 and sanitizing a restore):
As for 4S battery life. Try doing this,
1. Settings>Location Service ... disable all location services you do not need. In particularly Facebook because it drains the battery a lot.
Scroll down to the bottom at Settings>Location services>System Services ... Disable Setting Time zone, location based iAds, Diagnostic & Usage.
2. Settings>Notification>Calendar ... turn off the Notification Centre.
3. Settings>General>Reset ... do Reset All Settings. Doing this will not wipe out your iPhone. It will just Reset the network settings, location warning, keyboard dictionary, etc... but it will clear up some corrupted data there. Generally this will help.
Try these 3 steps first... if it still drains a lot, try the following,
4. Drain your battery down to 1%. Then charge it up using USB from PC ... not the charger. The charger output 1.0 A ( x 5V from USB ... you get 5W power). From PC, output is only 0.5A x 5V = 2.5W power. Charging is slower but trickle charge 4S helps the battery retain its charge better. I think it takes about 3-3.5 hours to charge full from USB/PC compared to slightly below 2 hours using iPhone charger.
If after doing the above still could not solve your battery issues (mine with iOS 5.0 was ok up to step 4, but not iOS 5.0.1).... plug you iPhone to a charger (any charger), from iPhone, access your iCloud ... set it up if you havent. Back up your iPhone data to iCloud. if you do not have enough storage (only 5GB is free), go to details and select the apps you need its data backup, choose only those you really need and leave those unnecessary ones out. Back up your camera roll to your PC/Mac manually as it could be too big to backup to iCloud.... once you have it setup, make sure you are on Wifi ... tap backup to iCloud from your iPhone. It will take a while if the file is huge.
Once backup to iCloud is completed, plug your iPhone to PC/Mac and launch iTunes 10.5.1 (make sure you have 10.5.1)
Click Restore. It will automatically initiate a download of iOS 5.0.1 ipsw for iPhone 4S. Wait for the whole process to finish, ie. download, restore software/firmware.
Once its done, do not set up your iPhone from iTunes. Set it up on your iPhone. Go through the selection. When prompted, select restore from iCloud (from your iphone backup earlier). Keep your iphone plugged into iTunes while restoring backup from iCloud. Because while restoring from iClouds, some data will be synced from iTunes if you plug in, e.g. music, video, etc... unless you bought these content from iTunes store. Apps will be downloaded from App Store from the cloud.
Once it's all done restored. Turn off your iPhone,.. and turn it on again.
Now, hopefully your battery wont be draining so fast anymore. Usually it wont after this. But you need to charge your battery at least 4-5 cycles to stabilize the charge on the battery. I dont know why... but battery life seems to get better and better for me after a few charge cycles after all the above work.
Good luck. Let us know if it works for you.
W. Raider tips (Sirii):
Bottom line for me of things that helped battery life are:
1. Turing off Siri and Rebooting the phone by holding the Home button and Top button down, ignoring the slider, until the phone shut down. (turn off Siri, reboot, and check top front of iPhone 4S against a lesser camera like the front-facing camera on an iPad2 - making sure the IR sensor is off)
2. Fully draining the battery, meaning using the phone until it shuts itself off from a drained battery and then recharging it to 100% about 4, maybe 5 times. I charged it both with a Mac and a wall charger.
Hope this is helpful!
Comments
jmm514 remarks (Twitter):
I may have found something. I had Twitter disabled in my notifications, but got a tweet today that popped up on my home screen. Didn't know I had this enabled. At the bottom of the Twitter notification settings is the home scrren toggle. Since disabling this, battery life seems better. Considering there is no setting for frequency of checking for tweets, it appears the phone is continually connecting to wifi to check for new tweets.
tmksnyder comments (notifications, corrupt data in iCloud):
For me, I found my iphone on wifi mysteriously connecting to my mac. I eventually narrowed it down to the Apple Move Trailers app which keeps a file in iCloud. The phone was trying to sync the file with the mac in the background even when the Movie Trailers app was closed (hitting the red x). Based on my macosx logs the iCloud process that was trying to sync was working directly between the phone and the mac without using itunes by connecting to an https address hosted on the phone. It was connecting every 3 minutes and failing (while phone was awake or awake during during a notification). I also found that iCloud control panel on OSX would error if I tried to delete the file. I fixed it by removing the App and doing a hard reset which stopped the sync. I probably could have turned off iCloud document sync in the phone but didn't think of that. My battery life has greatly improved while at home on wifi.    I am now at 28 hrs standby, 2 hrs 20 minutes of usage, and 68% battery. It was ok before where I could get 20-30 hrs standby and 6 -8 hrs usage. My usage today was phone calls, 3g surfing, and music via bluetooth in the car.
I also found even with Itunes iMatch, if I mass updated tages, art work etc, it would hit the phone on wifi even in standby. I was amazed.   Granted if I am not doing updates, Match won't hot the phone so this was a once in awhile event. I could drop my percentage by 5-10% in a matter of minutes when doing updates.   I think a lot of our problems are background processes, associated with iCloud, notification, and apps. More features means more battery.   I think the key thing is to keep track of what has recently been added or changed if battery life gets worse all of a sudden.   It may be an app that was recently installed and if possible you may want to completely remove it and not just quit it.
With twitter, i think it uses push notifications so it doesn't need to be running and actively poll on the phone. For instance , if i quit the mail app, i still will get mail notifications and can swipe the message and load mail. Apple Push Notifications servics maintain the connection to the phone and there are likely pings or connection checks that occur for the service on an os level not an app level. This minimizes the load so there arent a bunch of apps all runing and constantly checking. The notification service , if it is contacted from twitter or another service with data, will check the settings you have registered to the with the apple push service and send the notification to your phone. No matter what, there is a drain with notifications. M hunch is once one application is configured to receive notifications, connection checking occurs betwen the push service and the phone so it knows where it is on the network. If it is implemented correctly, these checks arent frequent if you are still and more frequent as you move. The other drain is for when the noification hits and is processsed. If i get 9 emails over night, my screen just popped up for 20 seconds or so to process each message using battery. I would even think that just go from low power to turning n the screen uses more juice than if the device was already on and i get the message. On nights I get no notifications, I see a 3 or 4 percent drop. On nights with a number of notifications, i have seen up to a 10 percent drop. Besides notifications, wifi sync and icloud will poll on the local network and use up battery if the host computer is on and running itunes or trying to sync a data file that is corrupt (which i had with the apple movie trailers app causing my phone to drain). For me turning off wifi sync and remving a corrupt file in icloud solved my battery issues and I get over 24 hrs of standby with 6 to 9 hrs of use and this is with all the normal location services and push serivices turned on.
See http://developer.apple.com/library/mac/ipad/#documentation/NetworkingInternet/Co nceptual/RemoteNotificationsPG/ApplePushService/ApplePushService.html for more info. I think it has a good overview of how the notifications work.

Well seems like that rumor of iOS 5.0.1 is finally gone the way of the dogs since developers got a beta of 5.1. So as stated earlier in the master discussion-> I suspect if you are filling up this thread with false post or creating a master set of links to various post that are unreliable you are wasting your time. Press is not going to touch the story due to poor or inaccurate sources which may be links from the master thread. This can include inaccurate information, combination of conflicting post or postings from users which may not own the device. Reputable press organizations have policies that require discloser and strict rules about what is a reliable source for a story. It is clear that many of the post in the master thread, which are links presented here are questionable.
Sorry to say that postings taken without any analysis of their totality have been propagated via various sites, for example sites such as http://www.2012federalbudget(dot)com. (Do not visit but I suspect that this is not the 2012 federal-budget site you would expect based on analysis of the records. There are plenty of sites like http://www.2012federalbudget(dot)com propagating questionable post in these threads.) One site for example in the discussion thread used a self signed certificate, the site had a log in to allow users to enter their OpenID. Seems many of these sites are pop and drop drupel configurations.
So remember this is how the really bad rumor of iOS 5.0.2 got started, the 5.1 memory leak issue, iCloud Issues, call quality, address book, etc.
Some of the postings have been very comical, I think the latest now is a dropbox issue. Seems that the length of the previous thread has resulted in various app engines of some proxy servers/tools reaching their limits.
So I would make sure to know the source of any information you link to. Make sure you avoid entering any information to outside links such as OpenID or Apple ID, these are big prize items for anyone with malicious intent. If you have issues and are a valid user contact APPLE CARE. (Note link is using McAfee Secure Short URL Service, and is https.)
http://mcaf.ee/ricdt
The original solution still represents a high level of success for users having any battery issues.
Install 5.0.1 on your iPhone 4s. Some users posting they are still using older versions, bad fake serial numbers, etc.
Make sure your device can run iOS 5.0.1 and is not altered.
Make sure you use a new Sim, not some cut down version which many users admit to doing. (Again, worth confirming what people are posting.)
Reset the device doing a hard reset and software reset.
Let battery drain and then charge for the full cycle, which is 24 hours.
I think you will find you will get the battery usage that APPLE has stated for the device.
Best of luck, stay safe and thanks

Is there a way that i can downgrade my iOS 7.1 on my iPhone 4 to iOS 6xx? battery life not good, and performance isn't better than iOS 6.. Please apple i am really disappointed with iOS 7 on my iPhone 4

Is there a way that i can downgrade my iOS 7.1 on my iPhone 4 to iOS 6xx? battery life not good, and performance isn't better than iOS 6.. Please apple i am really disappointed with iOS 7 on my iPhone 4, it can runs great on iPhone above 4 such as 5/5s/etc.. iPhone 4 just good with iOS 6...

No.

My hard drive crashed on my Mac Book Pro and I just had it replaced yesterday. After restoring my data, Safari will not open. The error message I continue to receive is "Safari quit unexpectedly" Should I just delete the application and download a new?

My hard drive crashed on my Mac Book Pro and I just had it replaced yesterday. After restoring my data, Safari will not open. The error message I continue to receive is "Safari quit unexpectedly" Should I just delete the application and download a new one?

http://swcdn.apple.com/content/downloads/37/23/041-5058/lr5tynbldi18zcrqo8a8uq88 rnjushqliu/Safari6Lion.pkg
Here you go.....

Hi, I got my Mac in 2009 with photoshop elements on it - it's recently been wiped, however before the process we put Photoshpp onto a hard drive, we then copied it back over and it no longer works, I'm getting error code 150:30 and I'm being asked for a p

Hi, I got my Mac in 2009 with photoshop elements on it - it's recently been wiped, however before the process we put Photoshop onto a hard drive, we then copied it back over and it no longer works, I'm getting error code 150:30 and I'm being asked for a password... any ideas how to get it working again?

You can never, never migrate an installed copy of PSE. It's just too complex and you can't get to all the bits and bobs.
First you will have to download and run this:
Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6
which will not seem to do anything, but is necessary to break the links within PSE so that you can pitch the bits manually. Then you will have to go around, not only to applications, but also to your username>library>preferences and most importantly to the library at the top level of your hard drive>application support>adobe, and remove everything you can find. Spotlight will not help with this kind of search, so don't try that.
Then you can install PSE from scratch.

Optimizing iPhone battery life: Between charges and before replacement

FYI. An excellent iPhone battery care article by iPhoneAtlas.com:
Optimizing iPhone battery life: Between charges and before replacement
http://www.iphoneatlas.com/2007/07/09/optimizing-iphone-battery-life-between-cha rges-and-before-replacement/

OK, I agree that is a completely false statement. The rest of the article is pretty good.
If you assume a linear decrease in battery charge for each full cycle (which it really isn't, but much easier to model in a spreadsheet). Then 80% of original charge after 400 full cycles is approximately 0.8% loss in battery charge per full charge cycle (again this is a simplification, stay with me). This means that after 400 cycles, you are at approximately 80% of your original total charge level. As stated by Apple.
So, extrapolating that out to EOL (end of life) which Apple assumes to be 50% battery charge, it would take approximately 1,000 full charge cycles for your battery to be EOL (according to Apple). It would actually be slightly less than that since it won't be a linear function.
For me, that's 2 to 4 years of use depending on whether or not I continue using the iPhone as much as I have this first full week.

I have an external hard drive that was formatted by a PC and has files and directories etc. I want to format it and use it on my IMAC for backup but I can't seem to write to it nor can I delete current content. How do I initialize it for use with the MAC?

I have an external hard drive that was formatted by a PC and has files and directories copied to it etc. I want to use it on my IMAC for backup. I see it on my my IMAC . I can open files etc. But I can't seem to write to it nor can I delete current content. I don't care if I lose current content. How do I initialize it for use with the MAC?

You can't write to it because it's formatted as NTFS which OS X will read but not write to. If you want to continue using the drive with both a PC and OS X you will need to download and install NTFS-3G so you can then write to it from your Mac. You can get NTFS-3G at:
http://www.macupdate.com/app/mac/24481/ntfs-3g
If you want to use the drive exclusively with your Mac then move the data off it and reformat it in Disk Utility (Applications - Utilities - Disk Utilities) as Mac OS Extended (Journaled.)

T420s hard drive noise / speed /battery life trade off and Screen Roll Cage Info

Similar Messages

Maybe you are looking for