T43 Touch Pad not working after Window 7 installation.

The Touch Pad on my T43 is not working with Window 7. I have tried several drivers without success; any suggestions??
Solved!
Go to Solution.

Did you try to install system update 4.0 to get all the correct drivers?
You can also enable/disable the touchpad in BIOS so you could doublecheck it's actually enabled. You can also enable/disable touchpad by going into the control panel, mouse and the Ultranav tab if you have the correct driver installed. Another options is to press Fn-F8 to enable/disable touchpad, but this one also require some drivers and software from Lenovo to work.
-gan

Similar Messages

  • Touch screen not working after windows 10

    Touch screen is not working after windows 10 was down loaded.  Also the zoom keeps changing on it's own.  Does anyone know how to fix this?

    Could you provide the unit's Model name/number?

  • Keyboard and Touch-Pad Not Working After Having to Install New Hard Drive

    I had to install a new hard drive in my HP Pavillion DV9700t that has Vista Home Premium 64-bit.  After going through the recovery process with backup disk the built in keyboard and touch-pad do not work.  During the installation, an error message came up saying something along the lines of "the drivers are not supported by this verison of windows because they are unsigned."  The drivers that had that error were "hpqkbfiltr keyboard filter driver," "HP remote control HID Device," and "hpqkdfilter driver."  I tried to update the drivers for the keyboard from the hp website, but the keyboard and touch-pad still do not work.
    My question is, where do I find the digitally signed drivers for the keyboard and touch-pad that Vista won't flag and disable?
    Help please!

    Sparkles,
    Thanks for the suggestions.
    When dealing with MS Fix It, I was choosing run.  Upon further investigation on that site, there really isn't a scan that applies to my issue anyways I tried the .NET Framework repair tool, and that seemed to work.  It told me to try re-running what I was having issues with, so I tried running the Windows PowerShell again, but again was faced with the following message "windows update standalone installer encountered an error: 0xc8000247." I went back to the .NET screen and hit "Next" because it didn't work, and that responded by saying they were going to submit logs to Microsoft.  I won't hold my breath on that one.
    I'm to the point where I honestly don't care anymore.  I have no idea what to do, because doing a clean install with the discs HP sent me isn't going to help because they are just recovery discs, and not an actual Windows disk.  This is the second hard drive I have had to put into my laptop and use those recovery disks on in the last 3-years.  The built-in keyboard hasn't worked during that time frame on either hard drive.  I don't think the recovery disks I was sent install properly.  Not sure where to go from here.  I spent way too much money on this laptop years ago having it custom built to handle all of my drafting programs, so I don't want to just kick it to the curb.  I was looking into the possibility of just replacing it, but I cannot stand the Windows 8 interface.
    I guess I should have fixed the issue with the keyboard on this hard drive before loading all of my programs.  Between the recovery disk install, formatting of the hard drive, and installing all of my programs it took well over 12 hours.  Not really looking forward ot that again Then there's shockwave and flash and all of the other goodies that my recovery disks won't restore anyways.
    Sorry if this seems like a negative post, but I'm just tired of trying to no avail.  Maybe I should just take it somewhere to get it looked at, but I can't see them being successful if the recovery disks won't help anyways.
    Thanks for you help,
    MadBuch

  • All button and touch pad not working except power button

    I face the problems that all button and touch pad not working after power on or wake up from sleep state except power button. And i have make the system sleep and wake again so that the mac book air can working as normal( mouse can move and button got response).

    Sometimes electrical components needs to have all power sources removed and reintroduced to work properly.  Try performing a hard reset first, if it doesn't work then we'll move to the next step.
    To Perform A Hard Reset
    Shut down the computer by going to the Start menu and selecting shut down. (If you have no display, hold the power button down for  5 seconds); (if the computer doesn't power on, move to the next step)
    Disconnect the AC Adapter from the notebook.
    Remove the battery from the bottom of the notebook.  There will be a switch/button to eject the battery.
    Wait at least 1 minute with all power sources disconnected.
    Re-insert the battery and reconnect the AC Adapter and then attempt to power on the notebook.

  • Touch pad not working with HP G60 operating on Windows 7

    I have a HP G60 operating on Windows 7 (not sure bit) and have problems with touch pad not working.
    I was using touch pad and wireless mouse interchangeably for past year.
    No recent changes made to system. Suddenly not work one evening. Have tried shutting down and left overnight which has not resolve problems.  On one occasion, i was not even able to type and that resolved after re-starting computer.
    There is a button between space bar and top of touch pad which is white. Even when i press and turn red, it has not changed situation. Therefore I have to use my wireless mouse to operate for the moment. 
    Would appreciate any advice about what is the problem and ways to resolve it.
    Thanks a lot!
    Mo

    Hi,
    The numbers are fine
    Try the following.
    First, ensure the Touchpad is switched on ( the light between the Touchpad and the Spacebar should be white ), then download the latest Synaptics driver installer on the link below and save it to your Downloads folder.
    http://ftp.hp.com/pub/softpaq/sp44501-45000/sp44940.exe
    Next, open windows Control Panel, open Programs and Features, right click the entry 'Synaptics Pointing Device Driver' and select Uninstall.
    When this has completed, shut down the notebook, remove any external devices connected to the notebook, unplug the AC Adapter and then remove the battery.  Hold  down the Power button for 30 seconds.  Re-insert the battery and plug in the AC Adapter.
    Tap away at the esc key as you start the notebook to launch the Start-up Menu and then select f10 to enter the bios menu.  Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter.  Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
    When windows has fully reloaded - it will automatically load a generic driver for the Touchpad, but just let it do this.  Then open your Downloads folder, right click the Synaptics installer and select 'Run as Administrator' to start the installation.  When this has completed, restart the notebook.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • HP Pavilion Volume Touch-Pad NOT WORKING | NO SOUND HELP

    HP Pavilion Volume Touch-Pad NOT WORKING
    I have an HP Pavilion dv3t - 2000, Windows Vista computer. 
    SOMEONE DID ALREADY HELP ME HERE WITH THIS PROBLEM BUT THEY STOPPED RESPONDING | Please check that link out!
    The volume touchpad above the keyboard is not working properly (There is no sound coming out of the speakers or the headphone jack) , If you touch the megaphone part of the touchpad above the keyboard then it stays red, however the sound icon on the taskbar changes from mute to unmuted when you touch the red megaphone. The volume slider on the touchpad works suprisingly.
    I don't know if I uninstalled something or what but I need this problem fixed!
    Thanks!

    Hi,
    Shut down the notebook, unplug the AC Adapter and remove the battery.
    Follow the procedure detailed on Page 63 of your Maintenance & Service Guide to remove the RTC battery.  Hold down the power button for 30 seconds.
    Leave the notebook for 10 minutes and then re-insert the RTC battery, re-assemble and replace the cover, insert the battery, plug in the AC Adapter and start the notebook.  Tap away at f10 as soon as you start the notebook to enter the bios menu.  Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter.  Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
    If you still have no audio and the installer you downloaded previously still doesn't detect the Hardware, it would start to look like a Hardware failure, but to try and rule out any further software cause, try the following.
    Follow the procedure on the link below to create a bootable Ubuntu CD and follow the steps in Part 3 to 'Try it' to see if this OS will run.  The 'Try it' option runs the OS from the CD without the need to install on your HDD.  If this runs Ok ( it will be slow running from a CD ) and you still have no audio output, this would tend to confirm a Hardware issue.
    http://www.ubuntu.com/desktop/get-ubuntu/download
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • HP Pavilion Volume Touch-Pad NOT WORKING | NO SOUND

    HP Pavilion Volume Touch-Pad NOT WORKING
    I have an HP Pavilion dv3t - 2000, Windows Vista computer. 
    The volume touchpad above the keyboard is not working properly (There is no sound coming out of the speakers or the headphone jack) , If you touch the megaphone part of the touchpad above the keyboard then it stays red, however the sound icon on the taskbar changes from mute to unmuted when you touch the red megaphone. The volume slider on the touchpad works suprisingly.
    I don't know if I uninstalled something or what but I need this problem fixed!
    Thanks!
    This question was solved.
    View Solution.

    Hi,
    Shut down the notebook, unplug the AC Adapter and remove the battery.
    Follow the procedure detailed on Page 63 of your Maintenance & Service Guide to remove the RTC battery.  Hold down the power button for 30 seconds.
    Leave the notebook for 10 minutes and then re-insert the RTC battery, re-assemble and replace the cover, insert the battery, plug in the AC Adapter and start the notebook.  Tap away at f10 as soon as you start the notebook to enter the bios menu.  Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter.  Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
    If you still have no audio and the installer you downloaded previously still doesn't detect the Hardware, it would start to look like a Hardware failure, but to try and rule out any further software cause, try the following.
    Follow the procedure on the link below to create a bootable Ubuntu CD and follow the steps in Part 3 to 'Try it' to see if this OS will run.  The 'Try it' option runs the OS from the CD without the need to install on your HDD.  If this runs Ok ( it will be slow running from a CD ) and you still have no audio output, this would tend to confirm a Hardware issue.
    http://www.ubuntu.com/desktop/get-ubuntu/download
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Synaptics Touch pad not working

    Hi there,
    My Synaptics Touch pad not working.
    System:  HP ProBook 4540S, MS Win8 x64 Ent.
    Please advise.
    Thanks in advance!

    Hello needsnow,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I understand that your Touchpad on the HP ProBook 4540s running Windows 8 is not working. I am sorry, but to get your issue more exposure, I would suggest posting it in the commercial forums, since this is a commercial product. You can do this at Notebook - HP ProBook, EliteBook, Compaq, Slate/Tablet PC, Armada, LTE.
    I hope this helps. Thank you for posting on the HP Forums. Have a great day!
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    Dunidar
    I work on behalf of HP
    Find out a bit more about me by checking out my profile!
    "Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

  • My hp 430 pc touch pad not working

    my hp 430 pc touch pad not working. please help me

    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • Touch pad not working of my laptop 48510s help for the same

    touch pad not working of my laptop 48510s help for the same

    Make sure you have the Current Version of iTunes Installed on your computer
    iTunes free download from www.itunes.com/download
    Then See Here  >  http://support.apple.com/kb/HT1808
    You may need to try this More than Once...  Be sure to Follow ALL the Steps...
    Take your time... Pay particular attention to Steps 3 and 4.
    After you have Recovered your Device...Re-Sync your Content
    Note:
    To remove a forgotten Restrictions passcode you will need to  Restore the Device as New...
    OR... From a Backup created Before the Restrictions Code was set....

  • My laser jet 100 color MFP M175nw is not working after windows 8.1 upgrade,

    my laser jet 100 color MFP M175nw is not working after windows 8.1 upgrade, driver on your website fails to setup at 83 % with an error message

    Welcome to the HP Forums  MillaMagia,
    I see by your post that the USB isn't being recognized.
    I can help you with this issue.
    Are you using the same USB cable? (known good USB cable)
    You want to use the normal USB slot 2.0 cable and not the latest USB 3.0.
    USB 3.0 are supposed to be backwards compatible.
    Try another USB port on the Laptop, some of the USB ports are more powered then others.
    I have provided a document to see if the printer is partially recognized in the device manager, which is causing the printer not to be recognized again. (the uninstall from the CD should have removed the entry and the printer from the registry)
    Leave the printer turned on and the USB cable connected directly to the computer and the printer's power cord directly into a wall outlet.
    How do I get into Windows Device Manager?
    Here is a document for Identifying problems in Windows Device Manager.
    Check to see if there are any hardware driver conflicts, you might see a ! mark or a red x beside a device with a conflict or unknown device, look under universal serial bus controllers, look for USB printing support or mass storage device, delete the entry by right clicking and select uninstall, OK.
    Let me know how it was listed. (screen shots welcome)
    If this is a Laptop then check the power management settings.
    Access the device manager. Windows 8-How do I access the Device Manager.
    Select universal serial bus controllers from the list, for each USB root hub, right click and left click on properties, for power management remove the check mark for "Allow the computer to turn off this device to save power". It allows the computer to limit or turn off power for this device.
    Disconnect the USB, run the full uninstall and reinstall the printer software again.
    If you need further assistance, let me know.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Lenovo A1 - Touch screen not working after digitizer replacemen​t

    After dropping my tablet and breaking the digitzer, I ordered a replacement digitzer from a company in China. (It took about a month to get it) After watching this video, I was able to install my new digitizer and it finally looked new again....well at least the screen!
    But.....when I powered up my tablet, the touch screen wasn't working..... I emailed back and forth with the company and they told me to install drive program, and send me a link to a site with a video, this site may have contained more than the video, but it was all in Chinese and I couldn't figure it out even with Google Translate. So I started researching. I thought I would try and load ICS on it, I thought, "Whats the worst thing that could happen?" it wasn't much more than a brick at this point anyways. 
    I found this website that let me through installing ICS on it. I had absolutly no expectations...but IT WORKED!!!! MY TOUCH SCREEN IS NOW WORKING!!!! I COULDN'T BELIEVE IT!!!
    When I was researching for this problem, there was absolutly no posts anywhere for "Touch screen not working after new digitizer". So I wanted to share my experience.

    Yea you are correct.....it must be a hardware problem. You must contact service centre of Lenovo and get help from there.
    You can say thank you by pressing the star left to my post IF I HELPED YOU

  • Ciscowork 3.2.1 daemon manager is not working after patch installation

    Hi Team
    Ciscowork 3.2.1 daemon manager is not working after patch installation.
    C:\Documents and Settings\Administrator>net start crmdmgtd
    The CiscoWorks Daemon Manager service is starting.
    The CiscoWorks Daemon Manager service could not be started.
    The service did not report an error.
    More help is available by typing NET HELPMSG 3534.
    Also I checked syslog.log and it is showing below error
    an 17 14:39:34 127.0.0.1 100: <28>   dmgt[1316]: 2507(W):Daemon manager anonymous user has not been set up: 00000569
    Please suggest.
    With Regards,
    neena

    During installation, an user casuser is created with certian security settings and if those are modified\removed, DM will not start.
    Following message will be seen in /log/syslog.log
    Daemon manager anonymous user has not been set up: 00000775
    To solve the issue, run resetcasuser.exe located under /setup.support  to  recreate the settings.
    Make sure casuser account is not locked out. Make sure casuser is a member of casusers group and is set to "password never expires".
    Additionally you can try to make casuser a member of adiministrators group.
    -Thanks

  • Ciscowork3.2.1 daemon manager is not working after patch installation

    Ciscowork 3.2.1 daemon manager is not working after patch installation
    Hi Team
    Ciscowork 3.2.1 daemon manager is not working after patch installation.
    C:\Documents and Settings\Administrator>net start crmdmgtd
    The CiscoWorks Daemon Manager service is starting.
    The CiscoWorks Daemon Manager service could not be started.
    The service did not report an error.
    More help is available by typing NET HELPMSG 3534.
    Also I checked syslog.log and it is showing below error
    an 17 14:39:34 127.0.0.1 100: <28>   dmgt[1316]: 2507(W):Daemon manager anonymous user has not been set up: 00000569
    I reset the casuser password and restarted the service but still no luck....
    Please suggest.
    With Regards,
    neena

    Neena,
    Check the properties of casuser under Start > Settings > Control Panel > Administrative Tools > Computer Management > Local Users and Groups > Users and make sure it is not disabled or locked out.  The only thing checked should be "Password never expires".  Change anything required and reset casuser.

  • Fingerprint Reader not working after windows password reset

    Hi There
    I was using windows login (single admin user) and fingerprint reader to login to my Thinkpad T510. Yesterday night I changed windows password and I didn't update finger print. Unfortunately I am not able to login when I tried to login using windows login today, I forgot the password and when I tried finger print reader it is just throwing error.
    Why finger print is not working after windows password reset? What should I do to login?
    Help would be appreciated!!

    I just called the tech support just now? I just asked the 'why the finger print reader not recognizing the finger print after changing windows password?', and he gave the following answers
    1. You should change fingerprint while changing windows password.  I don't understand the reason behind it, btw is this true?
    2. We can't do anything for this issue.

Maybe you are looking for